650 PHOENIX CONTACT Courtesy of Power/mation Energy Lane, Saint Paul, MN

Transcription

1 650 PHOENIX CONTACT

2 Monitoring relays, timer relays, function blocks The requirements pertaining to safety and system availability are constantly increasing regardless of the industry. Processes are becoming more and more complex, not only in mechanical engineering and the chemical industry but also in plant and automation technology. The requirements for power engineering are also constantly on the rise. A trouble-free and thus cost-effective operation can be achieved only with continuous monitoring of significant network and system parameters. Electronic monitoring relays of the EMD series are available for a wide variety of monitoring tasks to avoid the consequences of errors or to keep them within limits. The operating states are signaled using cololed reds, and errors that may occur can be sent to a controller through a floating contact or can switch off a section of the system. Some device versions are equipped with startup and response delays in order to briefly tolerate measured values outside the set monitoring range. The compact timer relays in the narrow 6.2 mm housing or multi-functional timer relays can be used in order to control time sequences in production and process technology. Program overview Electronic monitoring relay Single-phase current monitoring 652 Single-phase voltage monitoring 653 Three-phase voltage monitoring 654 Voltage indication modules 656 Load monitoring 657 Phase monitoring 657 Temperature monitoring (motor winding) 658 Level monitoring 659 Electronic timer relay Compact timer relay in just 6.2 mm 660 Multifunctional timer relay 662 Function blocks Diode modules 664 Lamp testing modules 665 Display modules 666 Motor attenuation modules 667 Monitoring relays The monitoring relays of the EMD series offer a cost-effective solution for monitoring tasks such as current, voltage, phase parameters, coil temperature, motor load and fluid level. Timer relays Compact timer relays in the narrow 6.2 mm housing with an adjustable time range and a function as well as multifunction timer relays are available. Function blocks In the function blocks, simple functions down to the component level are packaged for industrial use and provided with professional connection technology. Examples: diode modules, lamp testing modules, display modules, motor attenuation modules. PHOENIX CONTACT 651

3 Electronic monitoring relay Single-phase current monitoring The monitoring relays EMD-...V... monitor the direct and alternating currents from ma to A. The times for starting override (only for EMD-FL-...) and response delay can be set using the potentiometer. The operating states are displayed by LEDs. Floating PDT contacts are available as signal outputs. EMD-FL-C-10 Overcurrent/undercurrent monitoring, Window function, error memory EMD-SL-C-...C-10 Overcurrent/undercurrent monitoring I1 I2 I3 100 ma 1A 10 A I1 I2 I3 100 ma 1A 10 A Screw connection GND GND 15 = VAC/DC POWER MODLE =24VDC V AC Description Electronic monitoring relay for single-phase current with settable threshold value and delay EMD-FL-C EMD-SL-C-OC EMD-SL-C-C Power module, pluggable, please order at the same time! Supply voltage V DC EMD-SL-PS- 24DC Supply voltage V AC EMD-SL-PS- 24AC Supply voltage V AC EMD-SL-PS-110AC Supply voltage V AC EMD-SL-PS-120AC Supply voltage V AC EMD-SL-PS-230AC Technical data EMD-SL-C-OC-10 EMD-SL-C-C-10 Functions Overcurrent, undercurrent, window Overcurrent ndercurrent Input Input ranges 0 ma ma AC/DC (connection terminals: I1 and GND) 0 A... 1 A AC/DC (connection terminals: I2 and GND) 0 A A AC/DC (connection terminals: I3 and GND) 0 ma ma AC/DC (connection terminals: I1 and GND) 0 A... 1 A AC/DC (connection terminals: I2 and GND) 0 A A AC/DC (connection terminals: I3 and GND) Input resistance 470 mω (at I N = 100 ma) ; 47 mω (at I N = 1 A) ; 5 mω (at I N = 10 A) 470 mω (at I N = 100 ma) ; 47 mω (at I N = 1 A) ; 5 mω (at I N = 10 A) Min. setting range 5%... 95% (from I N ) 5%... 95% (from I N ) Max. setting range 10% % (from I N ) 10% % (from I N ) Setting range for response delay 0.1 s s 0.2 s s Setting range for starting delay 0 s s - Basic accuracy ± 5% (of scale end value) ± 5% (of scale end value) Setting accuracy 5% (of scale end value) 5% (of scale end value) Repeat accuracy 2% 2% Temperature influence < 0.1%/K < 0.1%/K Relay output Contact type 2 floating PDT contacts 1 floating PDT Switching capacity Electrical service life 2 x 10 5 cycles at ohmic load, 1000 VA 2 x 10 5 cycles at ohmic load, 1000 VA Mechanical life Approx. 2 x 10 7 cycles Approx. 2 x 10 7 cycles Output fuse 5 A (fast-blow) 5 A (fast-blow) Supply voltage 24 V AC V AC -15% % 24 V DC V DC -20% % 24 V AC V AC (see Power modules) 24 V DC (see Power modules) Nominal power consumption 4.5 VA (1.5 W) 2 VA (1.5 W) Recovery time 500 ms 500 ms Rated surge voltage 4 kv (basic insulation) 4 kv (basic insulation) Degree of protection IP40 (housing) / IP20 (connection terminal blocks) IP40 (housing) / IP20 (connection terminal blocks) Ambient temperature range -25 C C -25 C C Housing material Polyamide PA, self-extinguishing Polyamide PA, self-extinguishing Dimensions W / H / D 22.5 / 90 / 113 mm 22.5 / 90 / 113 mm Conformity CE compliant CE compliant L, SA / Canada L/C-L listed L 508 L/C-L listed L PHOENIX CONTACT

4 Single-phase voltage monitoring INTERFACE Monitoring Electronic monitoring relay The monitoring relays EMD-...C... monitor the direct and alternating current voltages from V to V. The times for starting override (only for EMD-FL-...) and response delay can be set using the potentiometer. The operating states are displayed by LEDs. Floating PDT contacts are available as signal outputs. EMD-FL-V-300 ndervoltage/overvoltage monitoring, Window function, error memory EMD-SL-V-V-300 ndervoltage monitoring V 1 30 V Screw connection GND 60 V 300 V GND 60 V 300 V 15 = VAC/DC POWER MODLE =24VDC V AC Description Electronic monitoring relay for single-phase voltages with settable threshold value and response delay EMD-FL-V EMD-SL-V-V Power module, pluggable, please order at the same time! Supply voltage V DC EMD-SL-PS- 24DC Supply voltage V AC EMD-SL-PS- 24AC Supply voltage V AC EMD-SL-PS-110AC Supply voltage V AC EMD-SL-PS-120AC Supply voltage V AC EMD-SL-PS-230AC Technical data Functions ndervoltage, overvoltage, window ndervoltage Input Input ranges Input resistance 0 V V AC/DC (connection terminal blocks: 1 and GND) 0 V V AC/DC (connection terminal blocks: 2 and GND) 0 V V AC/DC (connection terminal blocks: 3 and GND) 47 kω (connection terminal blocks: 1 and GND) 100 kω (connection terminal blocks: 2 and GND) 470 kω (connection terminal blocks: 3 and GND) 0 V V AC/DC (connection terminal blocks: 1 and GND) 0 V V AC/DC (connection terminal blocks: 2 and GND) 0 V V AC/DC (connection terminal blocks: 3 and GND) 47 kω (connection terminal blocks: 1 and GND) 100 kω (connection terminal blocks: 2 and GND) 470 kω (connection terminal blocks: 3 and GND) Min. setting range 5%... 95% (from N ) 5%... 95% (from N ) Max. setting range 10% % (from N ) 10% % (from N ) Setting range for response delay 0.1 s s 0.2 s s Setting range for starting delay 0 s s - Basic accuracy ± 5% (of scale end value) ± 5% (of scale end value) Setting accuracy 5% (of scale end value) 5% (of scale end value) Repeat accuracy 2% 2% Temperature influence < 0.1%/K < 0.1%/K Relay output Contact type 2 floating PDT contacts 1 floating PDT Switching capacity Electrical service life 2 x 10 5 cycles at ohmic load, 1000 VA 2 x 10 5 cycles at ohmic load, 1000 VA Mechanical life Approx. 2 x 10 7 cycles Approx. 2 x 10 7 cycles Output fuse 5 A (fast-blow) 5 A (fast-blow) Supply voltage 24 V AC V AC -15% % 24 V DC V DC -20% % 24 V AC V AC (see Power modules) 24 V DC (see Power modules) Nominal power consumption 4.5 VA (1.5 W) 2 VA (1.5 W) Recovery time 500 ms 500 ms Rated surge voltage 4 kv (basic insulation) 4 kv (basic insulation) Degree of protection IP40 (housing) / IP20 (connection terminal blocks) IP40 (housing) / IP20 (connection terminal blocks) Ambient temperature range -25 C C -25 C C Housing material Polyamide PA, self-extinguishing Polyamide PA, self-extinguishing Dimensions W / H / D 22.5 / 90 / 113 mm 22.5 / 90 / 113 mm Conformity CE compliant CE compliant L, SA / Canada L/C-L listed L 508 L/C-L listed L 508 PHOENIX CONTACT 653

5 Electronic monitoring relay Three-phase voltage monitoring The monitoring relays EMD-...-3V... monitor interlinked AC voltages. The voltage monitoring device EMD-SL- 3V-400-N monitors the voltage of the individual phases in the three-phase 400 V system for overvoltage or undervoltage in relation to the neutral conductor. The response delay time can be set via the potentiometer. The operating states are displayed by LEDs. Floating PDT contacts are available as signal outputs. EMD-FL-3V-400(230) ndervoltage monitoring, window function, monitoring for asymmetry, phase sequence, phase failure Screw connection (N) = VAC/DC Description Electronic monitoring relay for three-phase voltages with settable threshold value and response delay Power module, pluggable, please order at the same time! Supply voltage V DC Supply voltage V AC Supply voltage V AC Supply voltage V AC Supply voltage V AC Supply voltage V AC EMD-FL-3V EMD-FL-3V Technical data EMD-FL-3V-400 EMD-FL-3V-230 Functions ndervoltage, window, asymmetry, phase sequence, phase failure ndervoltage, window, asymmetry, phase sequence, phase failure Input Input ranges 3 N ~ 400/230 V 3 N ~ 230/132 V Input resistance 1 MΩ 470 kω Min. setting range -30%... 20% (from N ) Max. setting range -20%... 30% (from N ) Setting range for response delay 0.1 s s Basic accuracy ± 5% (of scale end value) Setting accuracy 5% (of scale end value) Repeat accuracy 2% Temperature influence < 0.1%/K Relay output Contact type 2 floating PDT contacts Switching capacity N 24 V~ 0V 654 PHOENIX CONTACT N max. 20A Connection example Electrical service life 2 x 10 5 cycles at ohmic load, 1000 VA Mechanical life Approx. 2 x 10 7 cycles Output fuse 5 A (fast-blow) Supply voltage 24 V AC V AC -15% % 24 V DC V DC -20% % Nominal power consumption 4.5 VA (1.5 W) Recovery time 500 ms Rated surge voltage 4 kv (basic insulation) Degree of protection IP40 (housing) / IP20 (connection terminal blocks) Ambient temperature range -25 C C Housing material Polyamide PA, self-extinguishing Dimensions W / H / D 22.5 / 90 / 113 mm Conformity CE compliant L, SA / Canada L/C-L listed L 508

6 Electronic monitoring relay EMD-FL-3V-690(500) ndervoltage monitoring, window function, monitoring for asymmetry, phase sequence, phase failure EMD-SL-3V-400 Window function EMD-SL-3V-400-N Window function Housing width N 15 POWER MODLE = V AC POWER MODLE =24VDC V AC POWER MODLE =24VDC V AC EMD-FL-3V EMD-SL-3V EMD-SL-3V-400-N EMD-FL-3V EMD-SL-PS- 24DC EMD-SL-PS- 24DC EMD-SL-PS- 24AC EMD-SL-PS- 24AC EMD-SL-PS45-110AC EMD-SL-PS-110AC EMD-SL-PS-110AC EMD-SL-PS45-120AC EMD-SL-PS-120AC EMD-SL-PS-120AC EMD-SL-PS45-230AC EMD-SL-PS-230AC EMD-SL-PS-230AC EMD-SL-PS45-400AC EMD-FL-3V-690 EMD-FL-3V-500 ndervoltage, window, asymmetry, phase sequence, phase failure ndervoltage, window, asymmetry, phase sequence, phase failure Window Window 3 ~ 690 V 3 ~ 500 V 3 ~ 400 V 3 N ~ 400/230 V 1 MΩ 1 MΩ 1 MΩ 1 MΩ -30%... 20% (from N ) -30%... 20% (from N ) -30%... 20% (from N ) -20%... 30% (from N ) -20%... 30% (from N ) -20%... 30% (from N ) 0.1 s s 0.2 s s 0.2 s s ± 5% (of scale end value) ± 5% (of scale end value) ± 5% (of scale end value) 5% (of scale end value) 5% (of scale end value) 5% (of scale end value) 2% 2% 2% < 0.1%/K < 0.1%/K < 0.1%/K 2 floating PDT contacts 1 floating PDT 1 floating PDT 2 x 10 5 cycles at ohmic load, 1000 VA 2 x 10 5 cycles at ohmic load, 1000 VA 2 x 10 5 cycles at ohmic load, 1000 VA Approx. 2 x 10 7 cycles Approx. 2 x 10 7 cycles Approx. 2 x 10 7 cycles 5 A (fast-blow) 5 A (fast-blow) 5 A (fast-blow) 110 V AC V AC (see Power modules) 24 V AC V AC (see Power modules) 24 V DC (see Power modules) 24 V AC V AC (see Power modules) 24 V DC (see Power modules) 4.5 VA (1.5 W) 2 VA (1.5 W) 2 VA (1.5 W) 500 ms 500 ms 500 ms 6 kv (basic insulation) 4 kv (basic insulation) 4 kv (basic insulation) IP40 (housing) / IP20 (connection terminal blocks) IP40 (housing) / IP20 (connection terminal blocks) IP40 (housing) / IP20 (connection terminal blocks) -25 C C -25 C C -25 C C Polyamide PA, self-extinguishing Polyamide PA, self-extinguishing Polyamide PA, self-extinguishing 45 / 90 / 113 mm 22.5 / 90 / 113 mm 22.5 / 90 / 113 mm CE compliant CE compliant CE compliant L/C-L listed L 508 L/C-L listed L 508 L/C-L listed L 508 PHOENIX CONTACT 655

7 Electronic monitoring relay Voltage indication modules Correct invoicing on the basis of a measuring instrument is guaranteed only if the three phases,, and are available. The voltage indicating modules IEG-45-3LA/.../21 are used for monitoring, for example on a tariff changing board. These modules indicate all three phases with highaccuracy reading even in case of reverse voltages. These modules also have a floating PDT contact, thereby offering the convenience of voltage monitoring through remote querying. IEG 45-3LA/.../21 Voltage indication module with relay contact output Housing width 45 P Screw connection M3 11 Description Voltage indication module, with relay contact output, one PDT Operating voltage 400 V AC IEG 45-3LA/400/ Technical data Input Operating voltage N 400 V AC ±10% Display area 100 V AC Display elements Glow lamp (green cover) Current required per light indicator 5.3 ma (for N, ) 5.3 ma (for N, ) 7.9 ma (for N, ) Relay output Contact type Single contact, 1 PDT Contact material AgSnO Maximum switching voltage 250 V AC/DC Limiting continuous current 6 A Interrupting rating (ohmic load) max. 144 W (for 24 V DC) 1500 VA (for 250 V AC) Mechanical life Approx. 2 x 10 7 cycles Ambient temperature range -20 C C Standards/regulations IEC IEC A DIN VDE 0110 DIN VDE , draft Pollution degree / Surge voltage category 2 / III Mounting position Any Assembly In rows with zero spacing Dimensions W / H / D 45 / 79 / 74 mm Conformity CE compliant 656 PHOENIX CONTACT

8 Load monitoring INTERFACE Monitoring Electronic monitoring relay The monitoring relay EMD-FL-PF-400 is a cos ϕ monitor for load monitoring in one or three-phase networks with adjustable threshold values, separately adjustable starting override and response delay. Phase monitoring The monitoring relay EMD-SL-PH-400 monitors linked AC voltages with and without neutral conductors for phase sequence, phase failure and asymmetry. The value for asymmetry is set to 30%. EMD-FL-PF-400 Load monitoring EMD-SL-PH-400 Phase sequence, phase failure, asymmetry I Screw connection K (N) = VAC/DC Description Electronic monitoring relay for load monitoring in single-phase or three-phase networks with adjustable threshold values, separately adjustable starting override and response delay EMD-FL-PF Electronic monitoring relay for phase monitoring in three-phase voltage systems EMD-SL-PH Technical data Functions nderload, overload, Window Phase sequence, phase failure, asymmetry Input Input ranges 3 N ~ 415/240 V 400 V (3 N ~ 400/230 V) Input resistance 1 MΩ 15 kω Input ranges 0.5 A A (connection terminal blocks: i and k) - Overload capacity 12 A permanent - Input resistance 5 mω - Setting range for response delay 0.1 s s 350 ms (fixed setting) Setting range for starting delay 1 s s 500 ms (fixed setting) Switching threshold cos ϕ Min Max Asymmetry - Fixed, approx. 30% Basic accuracy ± 5% (At cos ϕ = 0.8) - Setting accuracy 5% (At cos ϕ = 0.8) - Repeat accuracy ± 1.8% - Temperature influence 0.1%/K - Relay output Contact type 2 floating PDT contacts 2 floating PDT contacts Switching capacity Electrical service life 2 x 10 5 cycles at ohmic load, 1000 VA 2 x 10 5 cycles at ohmic load, 1000 VA Mechanical life Approx. 2 x 10 7 cycles Approx. 2 x 10 7 cycles Output fuse 5 A (fast-blow) 5 A (fast-blow) Supply voltage 24 V AC V AC -15% % (from the measured voltage) 24 V DC V DC -20% % Nominal power consumption 4.5 VA (1.5 W) 9 VA Recovery time 500 ms 100 ms Rated surge voltage 4 kv (basic insulation) 4 kv (basic insulation) Degree of protection IP40 (housing) / IP20 (connection terminal blocks) IP40 (housing) / IP20 (connection terminal blocks) Ambient temperature range -25 C C -25 C C Housing material Polyamide PA, self-extinguishing Polyamide PA, self-extinguishing Dimensions W / H / D 22.5 / 90 / 113 mm 22.5 / 90 / 113 mm Conformity CE compliant CE compliant L, SA / Canada L/C-L listed L 508 L/C-L listed L 508 PHOENIX CONTACT 657

9 Electronic monitoring relay Temperature monitoring (motor winding) The monitoring relay EMD-SL-PTC monitors the motor winding temperatures by means of PTC (PTC thermistor resistance) as per DIN If the PTC total resistance is less than 3.6 kω (normal temperature of the motor) when the supply voltage is applied, the output relay picks up. If the total resistance rises above 3.6 kω (at least one of the PTCs has reached the nominal switch-off temperature), the output relay drops out. The output relay picks up again when the total resistance has dropped below 1.8 kω again after the PTC has cooled down, and either an internal or external reset button has been pressed or the power supply interrupted. EMD-SL-PTC Temperature monitoring of motor windings T T2 Screw connection R POWER MODLE =24VDC V AC Description Electronic monitoring relay for temperature monitoring of motor windings as per DIN N N PTC T1 T2 R Monitoring of motor winding temperatures PTC T1 T2 R EMD-SL-PTC Power module, pluggable, please order at the same time! Supply voltage V DC EMD-SL-PS- 24DC Supply voltage V AC EMD-SL-PS- 24AC Supply voltage V AC EMD-SL-PS-110AC Supply voltage V AC EMD-SL-PS-120AC Supply voltage V AC EMD-SL-PS-230AC Technical data Functions Winding temperature monitoring Input Total cold resistance < 1.5 kω Response value 3.6 kω (relay drops out) Release value 1.8 kω (relay picks up) Short circuit detection < 20 Ω Basic accuracy ± 10% (of scale end value) Repeat accuracy 2% Temperature influence < 0.1%/K Relay output Contact type 2 floating PDT contacts Switching capacity Electrical service life Mechanical life Output fuse Supply voltage 2 x 10 5 cycles at ohmic load, 1000 VA Approx. 2 x 10 7 cycles 5 A (fast-blow) 24 V AC V AC (see Power modules) 24 V DC (see Power modules) Nominal power consumption 2 VA (1.5 W) Recovery time 500 ms Rated surge voltage 4 kv (basic insulation) Degree of protection IP40 (housing) / IP20 (connection terminal blocks) Ambient temperature range -25 C C Housing material Polyamide PA, self-extinguishing Dimensions W / H / D 22.5 / 90 / 113 mm Conformity CE compliant L, SA / Canada L/C-L listed L 508 Shutdown and message in case of overload 658 PHOENIX CONTACT

10 Filling level monitoring INTERFACE Monitoring Electronic monitoring relay The monitoring relay EMD-SL-LL-230 monitors the level of electrically conductive liquids with the help of conductive probes (not included in the scope of supply). The sensitivity can be set from kω. The rotary switch can be used to select the following functions: Pump up: Pump up or minimum monitoring Pump down: Pump down or maximum monitoring A switch-on and release delay can be set using the rotary switch for sense wave and foam formation. EMD-SL-LL-230 Filling level monitoring Screw connection E1 E2 E =230VAC Description Electronic monitoring relay for level monitoring of conductive liquids Technical data Functions Input Measuring input Max. probe voltage Max. probe current Length of probe cable EMD-SL-LL Pumping up (minimum monitoring), pumping down (maximum monitoring) Conductive probe, type: SK1, SK2, SK3 16 V AC 7 ma < 1000 m Set value < 50% (Capacity 100 nf/km) < 100 m Set value 100% (Capacity 100 nf/km) Switching threshold Relay output Contact type Switching capacity Electrical service life Mechanical life Output fuse Supply voltage 0.25 kω kω (4 ms... 1 µs) 2 floating PDT contacts 2 x 10 5 cycles at ohmic load, 1000 VA Approx. 2 x 10 7 cycles 5 A (fast-blow) 230 V AC -15% % AC Nominal power consumption 2 VA (1.5 W) Recovery time 500 ms Rated surge voltage 4 kv (basic insulation) Degree of protection IP40 (housing) / IP20 (connection terminal blocks) Ambient temperature range -25 C C Housing material Polyamide PA, self-extinguishing Dimensions W / H / D 22.5 / 90 / 113 mm Conformity CE compliant PHOENIX CONTACT 659

11 Electronic timer relay Compact timer relays in just 6.2 mm The compact timer relays ETD-BL-1T-... with a design width of just 6.2 mm save up to 70% space in the control cabinet as compared to the conventional timer relays. With an adjustable time and a pre-defined function, this compact timer relay is ideal for simple applications. The supply of 24 V DC voltage and a PDT in the output result in a wide usage range. ETD-BL-1T-ON-... Time relay with switch-on delay (voltage controlled) and an adjustable time range Housing width 6.2 Ex: X Screw connection Spring-cage connection t =24VDC 11 Description Compact time relay, with screw connection Time range s ETD-BL-1T-ON- 10S Time range s ETD-BL-1T-ON-300S Time range min ETD-BL-1T-ON- 30MIN Time range min ETD-BL-1T-ON-300MIN Compact time relay, with spring-cage connection Time range s ETD-BL-1T-ON- 10S-SP Time range s ETD-BL-1T-ON-300S-SP Time range min ETD-BL-1T-ON- 30MIN-SP Time range min ETD-BL-1T-ON-300MIN-SP Technical data Functions ON: With switch-on delay N 24 VDC B Conveyor belt 1 starts immediately 1 Control contact Connection - Control pulse length Min. 50 ms Relay output Contact type 1 floating PDT Switching capacity 1500 VA (6 A / 250 V AC) Mechanical life Approx. 2 x 10 7 cycles Supply voltage 24 V DC (19,2 V DC...30 V DC) Nominal current typ. 15 ma (relay ON) 7 ma (relay OFF) Impulse withstand voltage 6 kv (according to EN 50178) Degree of protection IP20 Ambient temperature range -20 C C Housing material Polyamide PA, self-extinguishing Dimensions W / H / D 6.2 / 80 / 86 mm Conformity CE compliant ATEX Ex nac IIC T4 X N 24 VDC B Conveyor belt 2 stars with a time delay 660 PHOENIX CONTACT

12 Electronic timer relay ETD-BL-1T-ON-CC-... Timer relay with switch-on delay (with control contact) and an adjustable time range ETD-BL-1T-OFF-CC-... Timer relay with off delay (with control contact) and an adjustable time range ETD-BL-1T-F-... Timer relay with flasher function (beginning with the pulse) and an adjustable time range Housing width 6.2 Ex: X Housing width 6.2 Ex: X Housing width 6.2 Ex: X B B t t t =24VDC 11 =24VDC 11 =24VDC 11 ETD-BL-1T-ON-CC- 10S ETD-BL-1T-OFF-CC- 10S ETD-BL-1T-F- 10S ETD-BL-1T-ON-CC-300S ETD-BL-1T-OFF-CC-300S ETD-BL-1T-F-300S ETD-BL-1T-ON-CC- 30MIN ETD-BL-1T-OFF-CC- 30MIN ETD-BL-1T-F- 30MIN ETD-BL-1T-ON-CC-300MIN ETD-BL-1T-OFF-CC-300MIN ETD-BL-1T-F-300MIN ETD-BL-1T-ON-CC- 10S-SP ETD-BL-1T-OFF-CC- 10S-SP ETD-BL-1T-F- 10S-SP ETD-BL-1T-ON-CC-300S-SP ETD-BL-1T-OFF-CC-300S-SP ETD-BL-1T-F-300S-SP ETD-BL-1T-ON-CC- 30MIN-SP ETD-BL-1T-OFF-CC- 30MIN-SP ETD-BL-1T-F- 30MIN-SP ETD-BL-1T-ON-CC-300MIN-SP ETD-BL-1T-OFF-CC-300MIN-SP ETD-BL-1T-F-300MIN-SP ON-CC: With switch-on delay with control contact OFF-CC: Off delay with control contact F: Flashing beginning with pulse Non-floating, terminals -B1 Non-floating, terminals -B1 - Min. 50 ms Min. 50 ms Min. 50 ms 1 floating PDT 1 floating PDT 1 floating PDT 1500 VA (6 A / 250 V AC) 1500 VA (6 A / 250 V AC) 1500 VA (6 A / 250 V AC) Approx. 2 x 10 7 cycles Approx. 2 x 10 7 cycles Approx. 2 x 10 7 cycles 24 V DC (19,2 V DC...30 V DC) 24 V DC (19,2 V DC...30 V DC) 24 V DC (19,2 V DC...30 V DC) 15 ma (relay ON) 7 ma (relay OFF) 15 ma (relay ON) 7 ma (relay OFF) 15 ma (relay ON) 7 ma (relay OFF) 6 kv (according to EN 50178) 6 kv (according to EN 50178) 6 kv (according to EN 50178) IP20 IP20 IP20-20 C C -20 C C -20 C C Polyamide PA, self-extinguishing Polyamide PA, self-extinguishing Polyamide PA, self-extinguishing 6.2 / 80 / 86 mm 6.2 / 80 / 86 mm 6.2 / 80 / 86 mm CE compliant CE compliant CE compliant Ex nac IIC T4 X Ex nac IIC T4 X Ex nac IIC T4 X PHOENIX CONTACT 661

13 Electronic timer relay Multifunctional timer relays The four variants of the multifunctional timer relays ETD completely cover the range of classic applications. Each of these devices is a practical combination of functionality with extremely simple operation. The adjustable time ranges have been kept as wide as possible to allow them to be used in universal applications. The timer relay applications are therefore to be found not only in the ms range, but also in the range of days. The desired function can be set using the rotary switch. ETD-FL-2T-DTI Multifunctional timer relay with two settable times Y1 Y Screw connection t Z2 Z = VAC/DC Description Electronic timer relay with settable times Power module, pluggable, please order at the same time! Supply voltage V DC Supply voltage V AC Supply voltage V AC Supply voltage V AC Supply voltage V AC Technical data Functions ETD-FL-2T-DTI lp: Switched-mode beginning with the pause li: Switched-mode beginning with the pulse ER: With switch-on and release delay with control contact EWu: With switch-on delay and passing make contact, voltage controlled EWs: With switch-on delay and passing make contact with control contact WsWa: With switch-on delay and passing break contact with control contact Wt: Pulse sequence evaluation (retriggerable release delay) Y1 25 Y2 T<T1 Time ranges Setting range Control contact Connection Load capacity 50 ms h (10 time end ranges) Floating, basic isolation between connection and input/output/bridge Y1-Y2 Cannot carry load WATCHDOG Function: Pulse sequence evaluation Y1 25 Y2 WATCHDOG T<T1 T> T1 Message for incorrect pulse Cable length Control pulse length Relay output Contact type Switching capacity Max. 10 m Min. 50 ms (only with Wt function: > 7 ms) 2 floating PDT contacts Mechanical life Approx. 2 x 10 7 cycles Supply voltage 24 V DC V DC -20% % 24 V AC V AC -15% % Nominal power consumption 2.5 VA (1 W) Recovery time 500 ms Rated surge voltage 4 kv (basic insulation) Degree of protection IP40 (housing) / IP20 (connection terminal blocks) Ambient temperature range -25 C C Housing material Polyamide PA, self-extinguishing Dimensions W / H / D 22.5 / 90 / 113 mm Conformity CE compliant L, SA / Canada L/C-L listed L PHOENIX CONTACT

14 Electronic timer relay ETD-SL-1T-DTF Multifunctional timer relay with one settable time ETD-SL-2T-I Impulse encoder with settable pulse and pause times ETD-SL-1T-S Star/delta timer relay B t t t = VAC/DC = VAC/DC POWER MODLE =24VDC V AC ETD-SL-1T-DTF ETD-SL-2T-I ETD-SL-1T-S EMD-SL-PS- 24DC EMD-SL-PS- 24AC EMD-SL-PS-110AC EMD-SL-PS-120AC EMD-SL-PS-230AC E: With switch-on delay R: With release delay and control contact Es: With switch-on delay and control contact Wu: With passing make contact, voltage controlled Ws: With passing make contact and control contact Wa: With passing break contact and control contact Bi: Flashing beginning with pulse Bp: Flashing beginning with pause lp: Switched-mode beginning with the pause li: Switched-mode beginning with the pulse S: Star/delta startup 50 ms h (7 time end ranges) 50 ms h (7 time end ranges) 500 ms... 3 min (4 time end ranges) Non-floating, terminals -B1 - - Parallel switched minimum load current 1 VA (0.5 W), terminals B1 Max. 10 m - - Min. 70 ms floating PDT contacts 2 floating PDT contacts 2 floating PDT contacts Approx. 2 x 10 7 cycles Approx. 2 x 10 7 cycles Approx. 2 x 10 7 cycles 24 V DC V DC -20% % 24 V AC V AC -15% % 24 V DC V DC -20% % 24 V AC V AC -15% % 24 V DC (see Power modules) 24 V AC V AC (see Power modules) 2.5 VA (1 W) 2.5 VA (1 W) 2.5 VA (1 W) 500 ms 500 ms 500 ms 4 kv (basic insulation) 4 kv (basic insulation) 4 kv (basic insulation) IP40 (housing) / IP20 (connection terminal blocks) IP40 (housing) / IP20 (connection terminal blocks) IP40 (housing) / IP20 (connection terminal blocks) -25 C C -25 C C -25 C C Polyamide PA, self-extinguishing Polyamide PA, self-extinguishing Polyamide PA, self-extinguishing 22.5 / 90 / 113 mm 22.5 / 90 / 113 mm 22.5 / 90 / 113 mm CE compliant CE compliant CE compliant L/C-L listed L 508 L/C-L listed L 508 L/C-L listed L 508 PHOENIX CONTACT 663

15 Function blocks Diode modules Diode circuits fulfill the most varied requirements in electrical and, above all, electronic control systems, for example: The electrical decoupling of messages in fault warning systems or As spark arrester diodes for damping surge voltages of inductive consumers, e.g. solenoid valves, direct voltage relays etc. Due to these requirements, diode modules are available as "diode gates" with common anode or cathode or as diodes for free assignment. EMG...-DIO With diode type 1 N 4007 EMG...-DIO With diode type 1 N 5408 Note: Further circuit diagrams can be found in the data sheet at P P Screw connection M Description Housing width Diode module, can be individually wired 4 diodes 22.5 mm EMG 22-DIO 4E EMG 22-DIO 4E-1N diodes 45 mm EMG 45-DIO 8E EMG 45-DIO 8E-1N diodes 90 mm EMG 90-DIO 17E Diode module, with P polarity (common cathode) 4 diodes 22.5 mm EMG 22-DIO 4P-1N diodes 22.5 mm EMG 22-DIO 7P diodes 45 mm EMG 45-DIO 8P-1N diodes 45 mm EMG 45-DIO14P diodes 90 mm EMG 90-DIO 32P Diode module, with M polarity (common anode) 4 diodes 22.5 mm EMG 22-DIO 4M-1N diodes 22.5 mm EMG 22-DIO 7M diodes 45 mm EMG 45-DIO 8M-1N diodes 45 mm EMG 45-DIO14M diodes 90 mm EMG 90-DIO 32M Equipment marker EMG-GKS EMG-GKS Technical data 4E / 8E / 17E / 7P / 7M 14P / 14M / 32P / 32M 4E-... / 4P-... / 4M-... / 8E-... 8P-... / 8M-... Diodes Max. operating voltage max 250 V AC 250 V AC 250 V AC 250 V AC Peak reverse voltage per diode 1300 V 1300 V 1000 V 1000 V Reverse current per diode 5 µa 5 µa 10 µa 10 µa Conducting state voltage per diode Approx. 0.8 V Approx. 0.8 V Approx. 0.8 V Approx. 0.8 V Conducting state current per diode with single load 0.7 A 0.7 A 1.5 A 2.5 A with simultaneous loads 0.5 A 0.2 A 1 A 0.3 A Ambient temperature range -20 C C -20 C C Standards/regulations IEC 664 IEC 664 A DIN VDE DIN VDE 0160 IEC 664 IEC 664 A DIN VDE DIN VDE 0160 Pollution degree / Surge voltage category 2 / III 2 / III Mounting position Any Any Assembly In rows with zero spacing In rows with zero spacing Dimensions H / D 75 / 55 mm 75 / 55 mm Conformity CE compliant CE compliant 664 PHOENIX CONTACT

16 Lamp testing modules INTERFACE Monitoring Function blocks Lamp test circuits, which decouple signals so that they are non-interacting, can be designed with two module versions: The diodes are connected in pairs, and circuit connections can be freely made to the anodes, For each diode pair, one anode is connected to a common point. Note: Further circuit diagrams can be found in the data sheet at EMG /LP EMG /LP Housing width 45 P Housing width 90 P Screw connection M Description Lamp testing module, two diodes each with common cathode: Version: with 4 pairs, for individual wiring EMG 45-DIO 8E/LP Version: with 7 pairs, with common triggering EMG 45-DIO14M/LP Lamp testing module, two diodes each with common cathode: Version: with 8 pairs, for individual wiring EMG 90-DIO 16E/LP Version: with 16 pairs, with common triggering EMG 90-DIO 32M/LP Equipment marker EMG-GKS EMG-GKS Technical data EMG 45-DIO 8E/LP EMG 45-DIO14M/LP EMG 90-DIO 16E/LP EMG 90-DIO 32M/LP Diodes Max. operating voltage max 250 V AC 250 V AC 250 V AC 250 V AC Peak reverse voltage per diode 1300 V 1300 V 1300 V 1300 V Reverse current per diode 5 µa 5 µa 5 µa 5 µa Conducting state voltage per diode Approx. 0.8 V Approx. 0.8 V Approx. 0.8 V Approx. 0.8 V Conducting state current per diode with single load 0.7 A 0.7 A 0.7 A 0.7 A with simultaneous loads 0.4 A 0.2 A 0.4 A 0.2 A Ambient temperature range -20 C C -20 C C Standards/regulations IEC 664 IEC 664 A DIN VDE DIN VDE 0160 IEC 664 IEC 664 A DIN VDE DIN VDE 0160 Pollution degree / Surge voltage category 2 / III 2 / III Mounting position Any Any Assembly In rows with zero spacing In rows with zero spacing Dimensions W / H / D 45 / 75 / 55 mm 90 / 75 / 55 mm Conformity CE compliant CE compliant PHOENIX CONTACT 665

17 Function blocks Display modules Light indicator modules facilitate the monitoring of sequences of electronic control systems and are a useful troubleshooting tool. The LEDs can be labeled individually. EMG 22-LED Display module with seven LEDs/glow lamps EMG 45-LED Display module with 14 LEDs P Housing width 45 P Screw connection M Description Display module, with LED reds and common return line Input voltage 24 V DC EMG 22-LED 7S/ EMG 45-LED 14S/ Display module, with glow lamps and common return line Input voltage V AC EMG 22-LA 7S/ Equipment marker EMG-GKS EMG-GKS Technical data EMG 22-LED 7S/24 EMG 22-LA 7S/230 Input Display elements 7 LEDs 7 glow lamps 14 LEDs Current required per light indicator Approx. 3 ma Approx. 1 ma Approx. 3 ma Ambient temperature range -20 C C -20 C C Standards/regulations IEC 664/IEC 664 A/DIN VDE : , Gr. B for 5, 12, 24, 60 V AC, Gr. C for 250 V AC DIN VDE 0160 IEC 664/IEC 664 A/DIN VDE : , Gr. B for 5, 12, 24, 60 V AC, Gr. C for 250 V AC DIN VDE 0160 Pollution degree / Surge voltage category 2 / III 2 / III Mounting position Any Any Assembly In rows with zero spacing In rows with zero spacing Dimensions W / H / D 22.5 / 75 / 47.5 mm 45 / 75 / 47.5 mm Conformity CE compliant CE compliant 666 PHOENIX CONTACT

18 Motor attenuation modules (RC modules) Inductivities of motors or contactor coils can superimpose DC and AC circuits with dangerous voltages. RC elements have proven to be suitable for attenuation. The compact motor attenuation modules for star-connected circuits can be installed in the terminal boxes on-site, i.e. far away from electrical control systems. Suitable RC elements for ranges from 4 to 7.5 kw are selected according to: Operating voltage, Three-phase performance. INTERFACE Monitoring Function blocks EMG 17-RC/.../S Motor attenuation module for star circuit Housing width 17.5 P Screw connection M3 N Description Motor attenuation module, for star-connected three-phase motors Motor capacity 4 kw EMG 17-RC/0,22MYF/220R/S Motor capacity 7.5 kw EMG 17-RC/0,47MYF/220R/S Equipment marker EMG-GKS Technical data EMG 17-RC/0,22MYF/220R/S EMG 17-RC/0,47MYF/220R/S Input Nominal voltage N 500 V AC 500 V AC Power dissipation 0.5 W 0.5 W Frequency range 50 Hz (60 Hz) 50 Hz (60 Hz) Resistor in RC combination 220 Ω 220 Ω Capacitor in RC combination 0.22 µf 0.47 µf Ambient temperature range -20 C C Mounting position Any Assembly In rows with zero spacing Dimensions W / H / D 17.5 / 75 / 100 mm Conformity CE compliant PHOENIX CONTACT 667