EMC TEST REPORT Model: 053-EMC-TR_ING, rev. 12 del 15/05/08. Laboratory identification: L.E.M. S.r.l. UNI CEI EN ISO/IEC EMC Laboratory

Transcription

1 L.E.M. S.r.l. Notified Body (ID 2034) EMC TEST REPORT Model: 053-EMC-TR_ING, rev. 12 del 15/05/08 Laboratory identification: L.E.M. S.r.l. UNI CEI EN ISO/IEC EMC Laboratory recognized by Ministry of Communication (ID 2034) Number: RP Issue date: 12/12/2008 Revision: 0 Customer: Model: ALBERTO SASSI SpA G300L1 Test performed: From 09/12/2008 on 10/12/2008 This Test Report has been issued according to specific model approved by the Laboratory Director. The results reported are valid only for the sample(s) tested. All rights reserved: no part of this report may be reproduced or distributed in any form or by any means without prior written authorization of L.E.M. S.r.l. Written by: Eng. Danilo Paolino Laboratory Technician Signature: Approved by: Eng. Alessandro Peluso Laboratory Director Signature: L.E.M. S.r.l. Via Caduti Di Melissa Casalecchio di Reno (BO) Telefono: Fax: notified-body@lem-emc.it Registro Imprese di Bologna e Codice Fiscale P.IVA IT R.E.A.Bologna n N Mecc. BO Capitale Sociale Euro ,00 i.v Date 12/12/2008 Page 1 of 19

2 CONTENTS 1. TEST PLANNING SCOPE DEVICE(S) CRITERION OF SELECTION PERFORMANCE CRITERIA FOR TEST EVALUATION 3 2. EQUIPMENT UNDER TEST SPECIFICATION EUT DESCRIPTION PORTS IDENTIFICATION E.U.T. OPERATING MODE DURING THE TESTS 4 3. STANDARD REFERENCE 5 4. TESTS PERFORMED AND RESULT SUMMARY CONTENTS OF THE ENCLOSURES 6 5. REFERENCE TEST EQUIPMENT TESTING AND CALIBRATIONS MEASUREMENT UNCERTAINTY 8 6. DETAILS OF THE TESTING PROCEDURE RADIATED EMISSION ELECTROSTATIC DISCHARGE IMMUNITY (ESD) RADIO FREQUENCY ELECTROMAGNETIC FIELD - (AM) ELECTRIC FAST TRANSIENT IMMUNITY (BURST) RADIO FREQUENCY COMMON MODE TEST SET UP RESULT OF ELECTROMAGNETIC EMISSION 17 Date 12/12/2008 Page 2 of 19

3 1. TEST PLANNING 1.1 Scope The aim of the tests is to determine the EUT behavior according to current standard requirements. 1.2 Device(s) criterion of selection A random sample was chosen for the test at the end of the production range. 1.3 Performance criteria for test evaluation The performance criteria evaluation of the results of the Emission test considers the fact that the level of the disturbance output of the device must not exceed the required limit according to the classification of the standard. The device is subject to generated disturbances during the Immunity test according to the procedure requirements of the standard. Its behavior is classified in criteria which are defined by the standard itself and listed below: Performance criterion A : The apparatus/ assembly of apparatus shall continue to operate as intended. No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer, when the apparatus or assembly of apparatus is used as intended. In some cases the performance level may be replaced by a permissible loss of performance. If the minimum performance level or the permissible performance loss is not specified by the manufacturer then either of these may be derived from the product description and documentation and what the user may reasonably expect from the apparatus or assembly of apparatus if used as intended. Performance criterion B: The apparatus/ assembly of apparatus shall continue to operate as intended after the test. No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer, when the apparatus or assembly of apparatus is used as intended. In some cases the performance level may be replaced by a permissible loss of performance. During the test, degradation of performance is however allowed. No change of actual operating state or stored data is allowed. If the minimum performance level or the permissible performance loss is not specified by the manufacturer than either of these may be derived from the product description and documentation and what the user may reasonably expect from the apparatus or assembly of apparatus if used as intended. Performance criterion C: Not used. Performance criterion D: The apparatus/ assembly of apparatus and the associated safety component(s) shall continue to operate as intended. No degradation of performance or loss of function is allowed other than a failure into a safe mode. Date 12/12/2008 Page 3 of 19

4 2. EQUIPMENT UNDER TEST SPECIFICATION 2.1 EUT description - Manufacturer: ALBERTO SASSI S.p.a. - Customer: ALBERTO SASSI S.p.a. - Customer address: Via Guido Rossa 1 - Crespellano (BO) - Contact person: Eng. Scarpetti - Person present during the tests: Mr. Albertazzi Eng. Scarpetti - Device: MOTOR AND BRAKING SYSTEM FOR LIFT - Model: G300L1 - Serial number: 08A09725/1 - Rated voltage: 400 VAC - Rated power: 11.4 KW - Rated current: A - Auxiliary device(s): CONTROL UNIT PROVIDED BY ALBERTO SASSI S.P.A. - Classification of EUT: LIFT APPARATUS ACCORDING TO UNI EN Ports Identification Description Enclosure composition Dimensions (mm) Enclosure Metallic container 560 x 330 x 480 Port Description Connection Point Length AC Power Port 400 Vac L1/ L2/ L3/ Pe Shielded cable Enclosure > 3 m DC Power Port 207 Vdc Positive/ Negative Pole Enclosure > 3 m Signal Port Signal from encoder Shielded cable Enclosure > 3 m Signal Port Sensors from motor Shielded cable Enclosure > 3 m 2.3 E.U.T. operating mode during the tests The EUT test has been configured under normal working conditions as manufacturer intended. Date 12/12/2008 Page 4 of 19

5 3. STANDARD REFERENCE Standard Description Year CEI IEC CEI EN CEI IEC CEI EN CISPR 16-1 UNI EN UNI EN Electromagnetic compatibility (EMC). Part 4: Testing and measurement techniques- Section 2: Electrostatic discharge immunity test - Basic EMC publication Electromagnetic Compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test Electromagnetic compatibility (EMC) - Part 4: Testing and measurement techniques - Section 4: Electrical fast transient/burst immunity test - Basic EMC Publication Electromagnetic Compatibility (EMC) - Part 4: Testing and measurement techniques - Section 6: Immunity to conducted disturbance, inducted by radio frequency fields Specification for radio disturbance and immunity measuring apparatus and methods - Part 1: Radio disturbance and immunity measuring apparatus Electromagnetic compatibility (EMC) Product family standard for lifts, escalators and moving walks: Emission Electromagnetic compatibility (EMC) Product family standard for lifts, escalators and moving walks: Immunity A1 (99)+ A2 (01) A1 (01) TESTS PERFORMED AND RESULT SUMMARY This is the report of the tests performed on the device to determine the Emission and Immunity electromagnetic interference requirements listed below: PRODUCT FAMILY STANDARD REFERENCE UNI EN UNI EN This product family standard indicates which tests the EUT is subject to; these tests are present in the basic EMC publications listed below: EMISSION requirements Type of Test Basic Standard Result Conducted emission UNI EN NAB (1) Radiated emission UNI EN C Harmonic current emissions CEI EN NAB (2) Voltage fluctuations and flicker CEI EN NAB (3) IMMUNITY requirements Type of Test Basic Standard Result Immunity to electrostatic discharge (ESD) CEI IEC C Immunity to radio frequency electromagnetic field-(am) CEI EN C Immunity to electric fast transient (BURST) CEI IEC C Immunity to high voltage pulse (Surge) CEI EN NAB (4) Immunity to radio frequency common mode CEI EN C Immunity to voltage dips and short interruptions CEI EN NAB (5) Date 12/12/2008 Page 5 of 19

6 Result LEGEND C : The EUT complied with the test specification limit NC : The EUT did not comply with the test specification limit NE : Test not executed NAB : The test is not applicable because: (1) The AC/ DC output power ports have shielded cables. (2-3) Equipment not connected to public low-voltage network. (4) No input ports are present. (5) Equipment not connected to 50 Hz or 60 Hz AC network. 4.1 Contents of the enclosures - ENCLOSURES F1 : Radiated emission test set - up - ENCLOSURES F2 : Immunity to electrostatic discharge (ESD) test set - up - ENCLOSURES F3 : Immunity to radio frequency electromagnetic field-(am) test set - up - ENCLOSURES F4 : Immunity to electric fast transient (BURST) test set - up - ENCLOSURES F5 : Immunity to radio frequency common mode test set - up - ENCLOSURES G1 : Radiated emission test result Date 12/12/2008 Page 6 of 19

7 5. REFERENCE TEST EQUIPMENT LIST A Ref. L.E.M. TYPE MANUFACTURER Signal Analyzer PMM 802 L3/25-3 phase line impedance stabilization network PMM 803 PL-01 - Pulse limiter PMM 805 NSG EMC Burst generator SHAFFNER 806 NSG ESD Simulator SHAFFNER EMI Spectrum analyzer and preselector TEKTRONIX 809 EM phase line impedance stabilization network ELECTROMETRICS 811 FC W RF power amplifier KALMUS 812 EMCA 230/10A - 10W Ultra wide band RF amplifier DRESSLER Electromagnetic field strength meter PMM 815 BA-05 - Isotropic field sensor probe PMM 816 SMY 01 - Signal generator R & S 817 SHC 01 Voltage probe PMM 818 UCS 500 Surge and voltage dips generator EM TEST Ultra wide band antenna EMCO 820 OR 01 - Optical repeater PMM 821 CDN 801-M3/16 CDN for AC power lines FCC 822 CDN AF/4 CDN for signal lines DRESSLER 824 EM 7600 Transient limiter with 10 db attenuator ELECTROMETRICS 825 ACF 01 - Absorbing clamp FRANKONIA 829 CDN Capacitive coupling clamp SHAFFNER 839 FLH 75 75W RF amplifier FRANKONIA 840 BTA L Wide band antenna FRANKONIA 841 ER 55CR - EMI receiver AFJ 842 Semi-anechoic chamber FRANKONIA 843 Signal Squarer for SMY 01 / 02 L.E.M. 844 IEC 725 Decoupling network L.E.M Capacitive coupling probe L.E.M. 847 PMM 6600 RF power meter PMM 848 F120-9A - Current clamp FCC 849 F Current probe FCC 850 Shielded chamber COSTAN 851 ESM 100- Electromagnetic field meter MASCHEK 853 BA 01 Isotropic field sensor probe PMM A Signal generator HP 880 PM 6625 Counter frequency PHILIPS AMPL 2160 Wide band antenna SPIN AMPL 0926 Wide band antenna SPIN 887 SRG 3P32 3 phase coupling network surge test L.E.M. 888 CDN M4/32A CDN for AC power lines EM TEST 889 CDN M5/32A CDN for AC power lines EM TEST 891 SRG-N4S3 Signal coupling network for surge test L.E.M. 892 DIPS 3P-25A - 3 phase voltage dips generator S.P.E. 898 LISN 50 - CISPR 25 line impedance stabilization network L.E.M. 899 RFH W RF power amplifier SPIN 902 TDS Scope meter TEKTRONIX 903 IFR 2031 Signal generator MARCONI F 15W RF power amplifier OPHIR 911 LEM-IMM-16 Programmable generator L.E.M. 912 CDN 16-M3-12 CDN for AC power lines L.E.M. 914 CDN 16-T4-6 CDN for signal lines L.E.M db 25W - Power attenuator DICONEX 921 CDN M2/16A CDN for AC power lines L.E.M. 922 CDN M1/16A CDN for AC power lines L.E.M. 924 SRG-NS1 Signal coupling network for surge test L.E.M. 925 T2.C2 Filter Inductance TISCI 927 Antenna Doble Ridge Horn BBHA-9120A SCHWARZBECK Date 12/12/2008 Page 7 of 19

8 5.1 Testing and Calibrations All the equipment has been regularly checked and calibrated with timing and modalities issued by internal manual SCHEDE APPARECCHIATURE DI PROVA according to UNI EN ISO Measurement uncertainty All the measurement uncertainty values have been calculated as indicated in NAMAS NIS 81 The treatment of Uncertainty in EMC Measurements and SINAL DT-0002 Guida per la dichiarazione dell incertezza di Misura ( Guide for the declaration of uncertainty of Measurements ). The values below refer to testing equipment present in LIST A TYPE OF TEST UNCERTAINTY Radiated emission in Semi-anechoic chamber MHz db P.H. ± 3, P.V. ± 3, P.H. ± 3, P.V. ± 3,5 Radiated emission in O.A.T.S. MHz db P.H. ± 3, P.V. ± 3, P.H. ± 3, P.V. ± 3,9 Conducted emission ± 3,00 db Radiated power ± 3,68 db Harmonic current emissions ± 0,2 % Voltage fluctuations and flicker ± 0,2 % Electromagnetic field in the range khz ± 8 % Radio frequency electromagnetic field Uniformity field 0-6 db Electrostatic discharge immunity (ESD) 7 % Electric fast transient immunity (BURST) 10 % Power frequency magnetic field ± 0,5 A/m since 30 A/m ± 1 A/m since 1000 A/m Date 12/12/2008 Page 8 of 19

9 6. DETAILS OF THE TESTING PROCEDURE 6.1 Radiated Emission Test specifications Reference Standard : UNI EN Classification : Lift apparatus Test method and set up : According to internal procedure IP-04 See enclosure F1 Port : Enclosures Environmental testing conditions Temperature: 23 C Humidity: 45 % Pressure : 1005 hpa Frequency Limits MHz 40 db(µv/m) at 10 m MHz 47 db(µv/m) at 10 m Test result RESULT ENCLOSURE NOTE The measure was performed at 3 m in semi-anechoic chamber. COMPLY G1 Test performed with 2 KHz sampling frequency of the control unit inverter. Control unit placed out of semi-anechoic chamber. Alteration(s) performed Test equipment none LIST A - Ref. LEM Date 12/12/2008 Page 9 of 19

10 6.2 Electrostatic discharge immunity (ESD) Test specifications Reference Standard : CEI IEC Required performance criterion : B Test method and set up : According to internal procedure IP-08 See enclosure F2 Port : Enclosures Environmental testing conditions Temperature: 23 C Humidity: 45 % Pressure : 1005 hpa Test result TYPE OF DISCHARGE LEVEL POLARITY N. APPLICATION POINTS CRITERIA Contact discharge 4 KV ± 20 Screws of motor enclosure; screws of brake enclosure; screws of electronic board enclosure. A Indirect VCP 8 KV ± 20 VCP A HCP: Horizontal coupling plane VCP: Vertical coupling plane RESULT ENCLOSURE NOTE COMPLY / / Alteration(s) performed none Test equipment LIST A - Ref. LEM 806 Date 12/12/2008 Page 10 of 19

11 6.3 Radio frequency electromagnetic field - (AM) Test specifications Reference Standard : CEI EN Required performance criterion : A Test method and set up : According to internal procedure IP-11 See enclosure F3 Port : Enclosure Environmental testing conditions Temperature: 23 C Humidity: 45 % Pressure : 1005 hpa Interfering signal requirements SIGNAL CHARACTERISTIC Frequency range: MHz Frequency range: MHz Frequency range: MHz Level (UNMOD): 10 V/m Level (UNMOD): 10 V/m Level (UNMOD): 3 V/m Modulation: AM Modulation depth: 80% Modulation freq.: 1 KHz Polarization: H / V Step size: 1% DWT: 3000 ms Test result RESULT ENCLOSURE NOTE COMPLY - Criteria A / / Alteration(s) performed none Test equipment LIST A - Ref. LEM Date 12/12/2008 Page 11 of 19

12 6.4 Electric fast transient immunity (BURST) Test specifications Reference Standard : CEI IEC Required performance criterion : B Test method and set up : According to internal procedure IP-09 - See enclosure F4 Port : - AC power port - Ports for signal lines Environmental testing conditions Temperature: 23 C Humidity: 45 % Pressure : 1005 hpa Test result COUPLED TYPE LEVEL POLARITY TEST DURATION LINES CRITERIA Capacitive clamp 1 KV ± 1 minute AC power A Capacitive clamp 0,5 KV ± 1 minute Encoder signal A Capacitive clamp 0,5 KV ± 1 minute Sensors signal A RESULT ENCLOSURE NOTE COMPLY / / Alteration(s) performed none Test equipment LIST A - Ref. LEM Date 12/12/2008 Page 12 of 19

13 6.5 Radio frequency common mode Test specifications Reference Standard : CEI EN Required performance criterion : A Test method and set up : According to internal procedure IP-13 - See enclosure F5 Port(s) : - AC/DC power ports - Ports for signal lines Environmental testing conditions Temperature: 23 C Humidity: 45 % Pressure : 1005 hpa Interfering signal requirements TEST PARAMETERS PORTS LEVEL V RMS UNMOD FREQUENCY RANGE (MHZ) MODULATION DWT ms STEP % COUPLING DEVICE CRITERIA AC POWER AM 80% 1KHz CLAMP A DC POWER AM 80% 1KHz CLAMP A Signal encoder cable AM 80% 1KHz CLAMP A Signal sensors cable AM 80% 1KHz CLAMP A Test equipment RESULT ENCLOSURE NOTE COMPLY / / Alteration(s) performed none Test equipment LIST A - Ref. LEM Date 12/12/2008 Page 13 of 19

14 7. TEST SET UP ENCLOSURE F1 - Radiated emission test set - up (1 photograph) ENCLOSURE F2 - Immunity to electrostatic discharge (ESD) test set - up (1 photograph) Date 12/12/2008 Page 14 of 19

15 ENCLOSURE F3 - Immunity to radio frequency electromagnetic field-(am) test set - up (1 photograph) ENCLOSURE F4 - Immunity to electric fast transient (BURST) test set - up (1 photograph) Date 12/12/2008 Page 15 of 19

16 ENCLOSURE F5 - Immunity to radio frequency common mode test set - up (1 photograph) Date 12/12/2008 Page 16 of 19

17 8. RESULT OF ELECTROMAGNETIC EMISSION ENCLOSURE G1 Radiated emission test result 2 graphs Date 12/12/2008 Page 17 of 19

18 AFJ ER 55CR 9 Khz 1 GHz EMI RECEIVER 6.39 FIRMWARE VERSION: 8.15 OPERATOR: Eng. Danilo Paolino TITLE: G300L1 ON - VERTICAL POLARIZATION OF ANTENNA - PEAK DETECTOR SN: CORR. FACTOR: INPUT ATTENUATOR: INT. ATTENUATOR: DETECTOR: LIMIT 1: LIMIT 2: MODE: STEP FREQ.: IF BW: ANTENNAE CAVO 01 NONE AUTO PEAK UNI EN QP SWEEP 80 khz 120 khz Date 12/12/2008 Page 18 of 19

19 AFJ ER 55CR 9 Khz 1 GHz EMI RECEIVER 6.39 FIRMWARE VERSION: 8.15 OPERATOR: Eng. Danilo Paolino TITLE: G300L1 ON - HORIZONTAL POLARIZATION OF ANTENNA - PEAK DETECTOR SN: CORR. FACTOR: INPUT ATTENUATOR: INT. ATTENUATOR: DETECTOR: LIMIT 1: LIMIT 2: MODE: STEP FREQ.: IF BW: ANTENNAE CAVO 01 NONE AUTO PEAK UNI EN QP SWEEP 80 khz 120 khz Date 12/12/2008 Page 19 of 19