MP2305 2A, 23V Synchronous Rectified Step-Down Converter
|
|
- Anthony Morris
- 5 years ago
- Views:
Transcription
1 The Future of Analog IC Technology MP305 A, 3 Synchronous Rectified Step-Down Converter DESCRIPTION The MP305 is a monolithic synchronous buck regulator. The device integrates 30mΩ MOSFETS that provide A continuous load current over a wide operating input voltage of 4.75 to 3. Current mode control provides fast transient response and cycle-by-cycle current limit. An adjustable soft-start prevents inrush current at turn-on. Shutdown mode drops the supply current to µa. This device, available in an 8-pin SOIC package, provides a very compact system solution with minimal reliance on external components. EALUATION BOARD REFERENCE Board Number Dimensions E305DS-00A.0 X x.5 Y x 0.5 Z FEATURES A Output Current Wide 4.75 to 3 Operating Input Range Integrated 30mΩ Power MOSFET Switches Output Adjustable from 0.93 to 0 Up to 93% Efficiency Programmable Soft-Start Stable with Low ESR Ceramic Output Capacitors Fixed 340KHz Frequency Cycle-by-Cycle Over Current Protection Input Under oltage Lockout APPLICATIONS Distributed Power Systems Networking Systems FPGA, DSP, ASIC Power Supplies Green Electronics/ Appliances Notebook Computers MPS and The Future of Analog IC Technology are Trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION PUT 4.75 to EN SS GND 4 BS 3 SW MP305 5 FB COMP C6 (optional) 6 C3 3.3nF C5 0nF D B30 (optional) PUT 3.3 A MP305-TAC0 EFFICIENCY (%) Efficiency vs Load Current = = LOAD CURRENT (A) MP305-EC0 MP305 Rev /3/005 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. 005 MPS. All Rights Reserved.
2 MP305 A, 3 SYNCHRONOUS RECTIFIED, STEP-DOWN CONERTER PACKAGE REFERENCE BS SW GND 3 4 TOP IEW SS EN COMP FB MP305_PD0 Part Number* Package Temperature MP305DS SOIC8 40 to 85 C * For Tape & Reel, add suffix Z (eg. MP305DS Z) For Lead Free, add suffix LF (eg. MP305DS LF Z) ABSOLUTE MAXIMUM RATGS () Supply oltage to 6 Switch oltage SW... to 0.3 Boost oltage BS... SW 0.3 to SW 6 All Other Pins to 6 Junction Temperature...50 C Lead Temperature...60 C Storage Temperature C to 50 C Recommended Operating Conditions () Input oltage to 3 Output oltage to 0 Ambient Operating Temperature C to 85 C Thermal Resistance (3) θ JA θ JC SOIC C/W Notes: ) Exceeding these ratings may damage the device. ) The device is not guaranteed to function outside of its operating conditions. 3) Measured on approximately square of oz copper. ELECTRICAL CHARACTERISTICS =, T A = 5 C, unless otherwise noted. Parameter Symbol Condition Min Typ (4) Max Units Shutdown Supply Current EN = µa Supply Current EN =.0; FB = ma Feedback oltage FB Feedback Overvoltage Threshold. Error Amplifier oltage Gain A EA 400 / Error Amplifier Transconductance G EA I C = ±0µA 800 µa/ High Side Switch On Resistance R DS(ON) 30 mω Low Side Switch On Resistance R DS(ON) 30 mω High Side Switch Leakage Current EN = 0, SW = 0 0 µa Upper Switch Current Limit Minimum Duty Cycle 3.4 A Lower Switch Current Limit From Drain to Source. A COMP to Current Sense Transconductance G CS 3.5 A/ Oscillation Frequency F osc 340 KHz Short Circuit Oscillation Frequency F osc FB = 0 00 KHz Maximum Duty Cycle D MAX FB =.0 90 % Minimum On Time 0 ns EN Shutdown Threshold oltage EN Rising..3.5 EN Shutdown Threshold oltage Hysterisis 0 m EN Lockout Threshold oltage..5.7 EN Lockout Hysterisis 0 m MP305 Rev /3/005 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. 005 MPS. All Rights Reserved.
3 MP305 A, 3 SYNCHRONOUS RECTIFIED, STEP-DOWN CONERTER ELECTRICAL CHARACTERISTICS (continued) =, T A = 5 C, unless otherwise noted. Parameter Symbol Condition Min Typ (4) Max Units Input Under oltage Lockout Threshold Rising Input Under oltage Lockout Threshold Hysteresis 0 m Soft Start Current SS = 0 6 µa Soft Start Period C SS = 0.µF 5 ms Thermal Shutdown 60 C Note: 4) Guaranteed by design, not tested. P FUNCTIONS Pin # Name Description BS High-Side Gate Drive Boost Input. BS supplies the drive for the high-side N-Channel MOSFET switch. Connect a 0.0µF or greater capacitor from SW to BS to power the high side switch. Power Input. supplies the power to the IC, as well as the step-down converter switches. Drive with a 4.75 to 3 power source. Bypass to GND with a suitably large capacitor to eliminate noise on the input to the IC. See Input Capacitor. 3 SW Power Switching Output. SW is the switching node that supplies power to the output. Connect the output LC filter from SW to the output load. Note that a capacitor is required from SW to BS to power the high-side switch. 4 GND Ground. 5 FB 6 COMP 7 EN 8 SS Feedback Input. FB senses the output voltage to regulate that voltage. Drive FB with a resistive voltage divider from the output voltage. The feedback threshold is See Setting the Output oltage. Compensation Node. COMP is used to compensate the regulation control loop. Connect a series RC network from COMP to GND to compensate the regulation control loop. In some cases, an additional capacitor from COMP to GND is required. See Compensation Components. Enable Input. EN is a digital input that turns the regulator on or off. Drive EN high to turn on the regulator, drive it low to turn it off. Pull up with 00kΩ resistor for automatic startup. Soft-Start Control Input. SS controls the soft start period. Connect a capacitor from SS to GND to set the soft-start period. A 0.µF capacitor sets the soft-start period to 5ms. To disable the soft-start feature, leave SS unconnected. MP305 Rev /3/005 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. 005 MPS. All Rights Reserved.
4 MP305 A, 3 SYNCHRONOUS RECTIFIED, STEP-DOWN CONERTER TYPICAL PERFORMANCE CHARACTERISTICS =, O = 3.3, L = 0µH, C = 0µF, C = µf, T A = 5 C, unless otherwise noted. Steady State Test =, = 3.3, I = 0A, I =8. ma Start-up through Enable =, = 3.3, I = A (Resistance Load) Shut-down through Enable =, = 3.3, I = A (Resistance Load) MP305-TPC0 ms/div. MP305-TPC0 ms/div. MP305-TPC03 Heavy Load Operation A Load Medium Load Operation A Load Light Load Operation No Load,AC 00m/div.,AC 00m/div.,AC 0m/div. O,AC 0m/div. O,AC 0m/div. O,AC 0m/div. A/div. A/div. A/div. SW 0/div. SW 0/div. SW 0/div. MP305-TPC04 MP305-TPC05 MP305-TPC06 Short Circuit Protection Short Circuit Recovery Load Transient /div. /div. O,AC 00m/div. A/div. A/div. A/div. OAD A/div. MP305-TPC07 MP305-TPC08 MP305-TPC09 MP305 Rev /3/005 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. 005 MPS. All Rights Reserved.
5 MP305 A, 3 SYNCHRONOUS RECTIFIED, STEP-DOWN CONERTER OPERATION FUNCTIONAL DESCRIPTION The MP305 is a synchronous rectified, current-mode, step-down regulator. It regulates input voltages from 4.75 to 3 down to an output voltage as low as 0.93, and supplies up to A of load current. The MP305 uses current-mode control to regulate the output voltage. The output voltage is measured at FB through a resistive voltage divider and amplified through the internal transconductance error amplifier. The voltage at the COMP pin is compared to the switch current measured internally to control the output voltage. The converter uses internal N-Channel MOSFET switches to step-down the input voltage to the regulated output voltage. Since the high side MOSFET requires a gate voltage greater than the input voltage, a boost capacitor connected between SW and BS is needed to drive the high side gate. The boost capacitor is charged from the internal 5 rail when SW is low. When the MP305 FB pin exceeds 0% of the nominal regulation voltage of 0.93, the over voltage comparator is tripped and the COMP pin and the SS pin are discharged to GND, forcing the high-side switch off. FB OP OSCILLATOR 00/340KHz RAMP CLK S CURRENT SENSE AMPLIFIER Q 5 BS SS ERROR AMPLIFIER R Q CURRENT COMPARATOR 3 SW COMP 6.5 EN OK. EN 4 GND OP < 4.0 LOCK COMPARATOR EN 7.3 SHUTDOWN COMPARATOR TERNAL REGULATORS 5 MP305_F0_BD0 Figure Functional Block Diagram MP305 Rev /3/005 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. 005 MPS. All Rights Reserved.
6 MP305 A, 3 SYNCHRONOUS RECTIFIED, STEP-DOWN CONERTER APPLICATIONS FORMATION COMPONENT SELECTION Setting the Output oltage The output voltage is set using a resistive voltage divider from the output voltage to FB pin. The voltage divider divides the output voltage down to the feedback voltage by the ratio: R FB = R R Where FB is the feedback voltage and is the output voltage. Thus the output voltage is: R R = 0.93 R R can be as high as 00kΩ, but a typical value is 0kΩ. Using the typical value for R, R is determined by: R = 0.83 ( 0.93) (kω) For example, for a 3.3 output voltage, R is 0kΩ, and R is 6.kΩ. Inductor The inductor is required to supply constant current to the output load while being driven by the switched input voltage. A larger value inductor will result in less ripple current that will result in lower output ripple voltage. However, the larger value inductor will have a larger physical size, higher series resistance, and/or lower saturation current. A good rule for determining the inductance to use is to allow the peak-to-peak ripple current in the inductor to be approximately 30% of the maximum switch current limit. Also, make sure that the peak inductor current is below the maximum switch current limit. The inductance value can be calculated by: L = fs IL Where is the output voltage, is the input voltage, f S is the switching frequency, and is the peak-to-peak inductor ripple current. Choose an inductor that will not saturate under the maximum inductor peak current. The peak inductor current can be calculated by: P = ILOAD fs L Where OAD is the load current. The choice of which style inductor to use mainly depends on the price vs. size requirements and any EMI requirements. Optional Schottky Diode During the transition between high-side switch and low-side switch, the body diode of the lowside power MOSFET conducts the inductor current. The forward voltage of this body diode is high. An optional Schottky diode may be paralleled between the SW pin and GND pin to improve overall efficiency. Table lists example Schottky diodes and their Manufacturers. Table Diode Selection Guide Part Number oltage/current Rating endor B30 30, A Diodes, Inc. SK3 30, A Diodes, Inc. MBRS30 30, A International Rectifier Input Capacitor The input current to the step-down converter is discontinuous, therefore a capacitor is required to supply the AC current to the step-down converter while maintaining the DC input voltage. Use low ESR capacitors for the best performance. Ceramic capacitors are preferred, but tantalum or low-esr electrolytic capacitors may also suffice. Choose X5R or X7R dielectrics when using ceramic capacitors. Since the input capacitor absorbs the input switching current it requires an adequate ripple current rating. The RMS current in the input capacitor can be estimated by: I C = I LOAD MP305 Rev /3/005 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. 005 MPS. All Rights Reserved.
7 MP305 A, 3 SYNCHRONOUS RECTIFIED, STEP-DOWN CONERTER The worst-case condition occurs at =, where I C = OAD /. For simplification, choose the input capacitor whose RMS current rating greater than half of the maximum load current. The input capacitor can be electrolytic, tantalum or ceramic. When using electrolytic or tantalum capacitors, a small, high quality ceramic capacitor, i.e. 0.µF, should be placed as close to the IC as possible. When using ceramic capacitors, make sure that they have enough capacitance to provide sufficient charge to prevent excessive voltage ripple at input. The input voltage ripple for low ESR capacitors can be estimated by: ILOAD = C fs Where C is the input capacitance value. Output Capacitor The output capacitor is required to maintain the DC output voltage. Ceramic, tantalum, or low ESR electrolytic capacitors are recommended. Low ESR capacitors are preferred to keep the output voltage ripple low. The output voltage ripple can be estimated by: = RESR f S L 8 fs CO Where C O is the output capacitance value and R ESR is the equivalent series resistance (ESR) value of the output capacitor. In the case of ceramic capacitors, the impedance at the switching frequency is dominated by the capacitance. The output voltage ripple is mainly caused by the capacitance. For simplification, the output voltage ripple can be estimated by: = 8 fs L CO In the case of tantalum or electrolytic capacitors, the ESR dominates the impedance at the switching frequency. For simplification, the output ripple can be approximated to: = R fs L ESR The characteristics of the output capacitor also affect the stability of the regulation system. The MP305 can be optimized for a wide range of capacitance and ESR values. Compensation Components MP305 employs current mode control for easy compensation and fast transient response. The system stability and transient response are controlled through the COMP pin. COMP pin is the output of the internal transconductance error amplifier. A series capacitor-resistor combination sets a pole-zero combination to control the characteristics of the control system. The DC gain of the voltage feedback loop is given by: A DC = RLOAD GCS A EA FB Where A EA is the error amplifier voltage gain; G CS is the current sense transconductance and R LOAD is the load resistor value. The system has two poles of importance. One is due to the compensation capacitor (C3) and the output resistor of the error amplifier, and the other is due to the output capacitor and the load resistor. These poles are located at: f f P P GEA = π C3 A = π C R O EA LOAD Where G EA is the error amplifier transconductance. The system has one zero of importance, due to the compensation capacitor (C3) and the compensation resistor (R3). This zero is located at: f Z = π C3 R3 The system may have another zero of importance, if the output capacitor has a large capacitance and/or a high ESR value. The zero, due to the ESR and capacitance of the output capacitor, is located at: f ESR = π C R O ESR MP305 Rev /3/005 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. 005 MPS. All Rights Reserved.
8 MP305 A, 3 SYNCHRONOUS RECTIFIED, STEP-DOWN CONERTER In this case (as shown in Figure ), a third pole set by the compensation capacitor (C6) and the compensation resistor (R3) is used to compensate the effect of the ESR zero on the loop gain. This pole is located at: f P 3 = π C6 R3 The goal of compensation design is to shape the converter transfer function to get a desired loop gain. The system crossover frequency where the feedback loop has the unity gain is important. Lower crossover frequencies result in slower line and load transient responses, while higher crossover frequencies could cause system instability. A good rule of thumb is to set the crossover frequency below one-tenth of the switching frequency. To optimize the compensation components, the following procedure can be used.. Choose the compensation resistor (R3) to set the desired crossover frequency. Determine the R3 value by the following equation: π CO fc π CO 0. fs R 3 = < GEA GCS FB GEA GCS FB Where f C is the desired crossover frequency which is typically below one tenth of the switching frequency.. Choose the compensation capacitor (C3) to achieve the desired phase margin. For applications with typical inductor values, setting the compensation zero, f Z, below one-forth of the crossover frequency provides sufficient phase margin. Determine the C3 value by the following equation: 4 C3 > π R3 f C 3. Determine if the second compensation capacitor (C6) is required. It is required if the ESR zero of the output capacitor is located at less than half of the switching frequency, or the following relationship is valid: π C O R f < S ESR If this is the case, then add the second compensation capacitor (C6) to set the pole f P3 at the location of the ESR zero. Determine the C6 value by the equation: C RESR C6 = R3 External Bootstrap Diode It is recommended that an external bootstrap diode be added when the system has a 5 fixed input or the power supply generates a 5 output. This helps improve the efficiency of the regulator. The bootstrap diode can be a low cost one such as 448 or BAT54. MP305 BS SW O 5 0nF MP305_F0 Figure External Bootstrap Diode This diode is also recommended for high duty cycle operation (when >65%) and high output voltage ( >) applications. Where R3 is the compensation resistor. MP305 Rev /3/005 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. 005 MPS. All Rights Reserved.
9 MP305 A, 3 SYNCHRONOUS RECTIFIED, STEP-DOWN CONERTER PACKAGE FORMATION SOIC8 P IDENT. 0.9(5.80) 0.44(6.00) 0.50(3.80) 0.57(4.000) (0.9) (0.49) SEE DETAIL "A" 0.03(0.330) 0.00(0.508) 0.050(.70)BSC 0.0(0.80) 0.00(0.508) x 45o 0.053(.350) 0.068(.730) 0.89(4.800) 0.97(5.004) 0.049(.50) 0.060(.54) 0.00(0.030) 0.004(0.0) SEATG PLANE 0 o -8 o 0.06(0.40) DETAIL "A" 0.050(.70) NOTE: ) Control dimension is in inches. Dimension in bracket is millimeters. NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MP305 Rev /3/005 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. 005 MPS. All Rights Reserved.
MP1482 2A, 18V Synchronous Rectified Step-Down Converter
The Future of Analog IC Technology MY MP48 A, 8 Synchronous Rectified Step-Down Converter DESCRIPTION The MP48 is a monolithic synchronous buck regulator. The device integrates two 30mΩ MOSFETs, and provides
More informationMP2307 3A, 23V, 340KHz Synchronous Rectified Step-Down Converter
The Future of Analog IC Technology TM TM MP307 3A, 3, 340KHz Synchronous Rectified Step-Down Converter DESCRIPTION The MP307 is a monolithic synchronous buck regulator. The device integrates 00mΩ MOSFETS
More informationMP1484 3A, 18V, 340KHz Synchronous Rectified Step-Down Converter
The Future of Analog IC Technology MP484 3A, 8, 340KHz Synchronous Rectified Step-Down Converter DESCRIPTION The MP484 is a monolithic synchronous buck regulator. The device integrates top and bottom 85mΩ
More informationMP1482 2A, 18V Synchronous Rectified Step-Down Converter
The Future of Analog IC Technology DESCRIPTION The MP48 is a monolithic synchronous buck regulator. The device integrates two 30mΩ MOSFETs, and provides A of continuous load current over a wide input voltage
More informationMP1570 3A, 23V Synchronous Rectified Step-Down Converter
Monolithic Power Systems MP570 3A, 23 Synchronous Rectified Step-Down Converter FEATURES DESCRIPTION The MP570 is a monolithic synchronous buck regulator. The device integrates 00mΩ MOSFETS which provide
More informationMP1472 2A, 18V Synchronous Rectified Step-Down Converter
The Future of Analog IC Technology MP472 2A, 8 Synchronous Rectified Step-Down Converter DESCRIPTION The MP472 is a monolithic synchronous buck regulator. The device integrates a 75mΩ highside MOSFET and
More informationMP2355 3A, 23V, 380KHz Step-Down Converter
The Future of Analog IC Technology MP2355 3A, 23, 380KHz Step-Down Converter DESCRIPTION The MP2355 is a step-down regulator with a built in internal Power MOSFET. It achieves 3A continuous output current
More informationMP2303 3A, 28V, 340KHz Synchronous Rectified Step-Down Converter
MP2303 3A, 28V, 340KHz Synchronous Rectified Step-Down Converter TM The Future of Analog IC Technology DESCRIPTION The MP2303 is a monolithic synchronous buck regulator. The device integrates power MOSFETS
More informationFEATURES DESCRIPTION APPLICATIONS PACKAGE REFERENCE
DESCRIPTION The is a monolithic synchronous buck regulator. The device integrates 100mΩ MOSFETS that provide 2A continuous load current over a wide operating input voltage of 4.75V to 25V. Current mode
More informationMP1482 2A, 18V Synchronous Rectified Step-Down Converter
The Future of Analog IC Technology MP48 A, 8V Synchronous Rectified Step-Down Converter DESCRIPTION The MP48 is a monolithic synchronous buck regulator. The device integrates two 30mΩ MOSFETs, and provides
More informationMP2307 3A, 23V, 340KHz Synchronous Rectified Step-Down Converter
The Future of Analog IC Technology MP2307 3A, 23V, 340KHz Synchronous Rectified Step-Down Converter DESCRIPTION The MP2307 is a monolithic synchronous buck regulator. The device integrates 00mΩ MOSFETS
More informationMP A, 28V, 1.4MHz Step-Down Converter
The Future of Analog IC Technology MP8373 3A, 8,.MHz Step-Down Converter DESCRIPTION The MP8373 is a.mhz step-down regulator with a built-in power MOSFET. It achieves 3A continuous output current over
More informationTechcode. 1.6A 32V Synchronous Rectified Step-Down Converte TD1529. General Description. Features. Applications. Package Types DATASHEET
General Description Features The TD1529 is a monolithic synchronous buck regulator. The device integrates two 130mΩ MOSFETs, and provides 1.6A of continuous load current over a wide input voltage of 4.75V
More informationMP2363 3A, 27V, 365KHz Step-Down Converter
The Future of Analog IC Technology MP363 3A, 7, 365KHz Step-Down Converter DESCRIPTION The MP363 is a non-synchronous step-down regulator with an integrated Power MOSFET. It achieves 3A continuous output
More informationMP A, 15V, 800KHz Synchronous Buck Converter
The Future of Analog IC Technology TM TM MP0.5A, 5, 00KHz Synchronous Buck Converter DESCRIPTION The MP0 is a.5a, 00KHz synchronous buck converter designed for low voltage applications requiring high efficiency.
More informationMP2303A 3A, 28V, 360kHz Synchronous Rectified Step-Down Converter
The Future of Analog IC Technology DESCRIPTION The MP33A is a monolithic synchronous buck regulator. The device integrates a 5mΩ high-side MOSFET and a 8mΩ low-side MOSFET that provide 3A continuous load
More informationMP2354 2A, 23V, 380KHz Step-Down Converter
The Future of Analog IC Technology MP2354 2A, 23V, 380KHz Step-Down Converter DESCRIPTION The MP2354 is a monolithic step down switch mode converter with a built in internal power MOSFET. It achieves 2A
More informationSGM6130 3A, 28.5V, 385kHz Step-Down Converter
GENERAL DESCRIPTION The SGM6130 is a current-mode step-down regulator with an internal power MOSFET. This device achieves 3A continuous output current over a wide input supply range from 4.5 to 28.5 with
More informationSGM6232 2A, 38V, 1.4MHz Step-Down Converter
GENERAL DESCRIPTION The is a current-mode step-down regulator with an internal power MOSFET. This device achieves 2A continuous output current over a wide input supply range from 4.5V to 38V with excellent
More informationidesyn id8802 2A, 23V, Synchronous Step-Down DC/DC
2A, 23V, Synchronous Step-Down DC/DC General Description Applications The id8802 is a 340kHz fixed frequency PWM synchronous step-down regulator. The id8802 is operated from 4.5V to 23V, the generated
More informationMP A, 15V, 800kHz Synchronous Buck Converter
The Future of Analog IC Technology MP206.5A, 5, 800kHz Synchronous Buck Converter DESCRIPTION The MP206 is a.5a, 800kHz synchronous buck converter designed for low voltage applications requiring high efficiency.
More informationMP2362 Dual 2A, 23V, 380KHz Step-Down Converter with Frequency Synchronization
The Future of Analog IC Technology MP36 Dual A, 3, 380KHz Step-Down Converter with Frequency Synchronization DESCRIPTION The MP36 is a dual monolithic step-down switch mode converter with built-in internal
More informationSGM6132 3A, 28.5V, 1.4MHz Step-Down Converter
GENERAL DESCRIPTION The SGM6132 is a current-mode step-down regulator with an internal power MOSFET. This device achieves 3A continuous output current over a wide input supply range from 4.5V to 28.5V
More informationAnalog Technologies. ATI2202 Step-Down DC/DC Converter ATI2202. Fixed Frequency: 340 khz
Step-Down DC/DC Converter Fixed Frequency: 340 khz APPLICATIONS LED Drive Low Noise Voltage Source/ Current Source Distributed Power Systems Networking Systems FPGA, DSP, ASIC Power Supplies Notebook Computers
More informationMP MHz, 18V Step-Up Converter
The Future of Analog IC Technology DESCRIPTION The MP540 is a 5-pin thin TSOT current mode step-up converter intended for small, low power applications. The MP540 switches at.mhz and allows the use of
More informationMP4458 1A, 4MHz, 36V Step-Down Converter
The Future of Analog IC Technology DESCRIPTION The MP4458 is a high frequency step-down switching regulator with an integrated internal high-side high voltage power MOSFET. It provides A output with current
More informationLSP5502 2A Synchronous Step Down DC/DC Converter
FEATURES 2A Output Current Wide 4.5V to 27V Operating Input Range Integrated 20mΩ Power MOSFET Switches Output Adjustable from 0.925V to 24V Up to 96% Efficiency Programmable Soft-Start Stable with Low
More informationMP1430 3A, 28V, 385KHz Step-Down Converter
TM MP0 A, 8, 85KHz tep-down Converter TM The Future of Analog IC Technology PRELIMARY RELEAE PECIFICATION UBJECT TO CHANGE DECRIPTION The MP0 is a step-down regulator with an internal Power MOFET. It achieves
More informationMP1495 High Efficiency 3A, 16V, 500kHz Synchronous Step Down Converter
The Future of Analog IC Technology DESCRIPTION The MP1495 is a high-frequency, synchronous, rectified, step-down, switch-mode converter with built-in power MOSFETs. It offers a very compact solution to
More informationMP A, 24V, 1.4MHz Step-Down Converter
The Future of Analog IC Technology DESCRIPTION The MP8368 is a monolithic step-down switch mode converter with a built-in internal power MOSFET. It achieves 1.8A continuous output current over a wide input
More informationHM1410 FEATURES APPLICATIONS PACKAGE REFERENCE HM1410
DESCRIPTION The is a monolithic step-down switch mode converter with a built in internal power MOSFET. It achieves 2A continuous output current over a wide input supply range with excellent load and line
More informationAT V,3A Synchronous Buck Converter
FEATURES DESCRIPTION Wide 8V to 40V Operating Input Range Integrated 140mΩ Power MOSFET Switches Output Adjustable from 1V to 25V Up to 93% Efficiency Internal Soft-Start Stable with Low ESR Ceramic Output
More informationAME. 40V CC/CV Buck Converter AME5244. n General Description. n Typical Application. n Features. n Functional Block Diagram.
5244 n General Description n Typical Application The 5244 is a specific 40 H buck converter that operates in either C/CC mode supports an put voltage range of 0.8 to 2 and support constant put current
More informationPACKAGE REFERENCE. ELECTRICAL CHARACTERISTICS V IN = 12V, T A = +25 C, unless otherwise noted.
PACKAGE REFERENCE TOP VIEW TOP VIEW BST 1 SW BST 1 SW GND 2 5 GND 2 5 FB 3 EN FB 3 EN MP2259_PD01_TSOT23 MP2259_PD02_SOT23 Part Number* Package Temperature MP2259DJ TSOT23-0 C to 85 C * For Tape & Reel,
More informationMP3115 High-Efficiency, Single-Cell Alkaline, 1.3MHz Synchronous Step-up Converter with Output Disconnect
The Future of Analog IC Technology MP3115 High-Efficiency, Single-Cell Alkaline, 1.3MHz Synchronous Step-up Converter with Output Disconnect DESCRIPTION The MP3115 is a synchronous, fixed frequency, current
More informationMP KHz/1.3MHz Boost Converter with a 2A Switch
The Future of Analog IC Technology DESCRIPTION The MP4 is a current mode step up converter with a A, 0.Ω internal switch to provide a highly efficient regulator with fast response. The MP4 can be operated
More informationMP V Input, 2A Output Step Down Converter
General Description The is a high voltage step down converter ideal for cigarette lighter battery chargers. It s wide 6.5 to 32V (Max = 36V) input voltage range covers the automotive battery requirements.
More informationEUP3410/ A,16V,380KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit
2A,16V,380KHz Step-Down Converter DESCRIPTION The is a current mode, step-down switching regulator capable of driving 2A continuous load with excellent line and load regulation. The can operate with an
More informationMP A, 55V, 100kHz Step-Down Converter with Programmable Output OVP Threshold
The Future of Analog IC Technology MP24943 3A, 55V, 100kHz Step-Down Converter with Programmable Output OVP Threshold DESCRIPTION The MP24943 is a monolithic, step-down, switch-mode converter. It supplies
More informationMP2143 3A, 5.5V, 1.2MHz, 40μA I Q, COT Synchronous Step Down Switcher
The Future of Analog IC Technology MP2143 3A, 5.5, 1.2MHz, 40μA I Q, COT Synchronous Step Down Switcher DESCRIPTION The MP2143 is a monolithic, step-down, switchmode converter with internal power MOSFETs.
More informationEUP3475 3A, 28V, 1MHz Synchronous Step-Down Converter
3A, 8, MHz ynchronous tep-down onverter DERIPTION The is a MHz fixed frequency synchronous current mode buck regulator. The device integrates both 35mΩ high-side switch and 90mΩ low-side switch that provide
More informationAME. High Voltage CC/CV Buck Converter AME5265. n Features. n General Description. n Applications. n Typical Application. n Functional Block Diagram
5265 n General Description The 5265 is a specific 40 maximum rating H buck converter that operates in either C/CC mode supports adjustable put voltage and support constant put current at 20KHz switching
More informationEUP3452A. 2A,30V,300KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit
2A,30V,300KHz Step-Down Converter DESCRIPTION The is current mode, step-down switching regulator capable of driving 2A continuous load with excellent line and load regulation. The can operate with an input
More informationMP9141 FEATURES DESCRIPTION APPLICATIONS PACKAGE REFERENCE
DESCRIPTION The is a monolithic step-down switch mode converter with a built in internal power MOSFET. It achieves 2A continuous output current over a wide input supply range with excellent load and line
More information3A, 36V, Step-Down Converter
3A, 36, Step-Down Converter FP6150 General Description The FP6150 is a buck regulator with a built in internal power MOSFET. It achieves 3A continuous output current over a wide input supply range with
More informationMP2494 2A, 55V, 100kHz Step-Down Converter
The Future of Analog IC Technology MP2494 2A, 55V, 100kHz Step-Down Converter DESCRIPTION The MP2494 is a monolithic step-down switch mode converter. It achieves 2A continuous output current over a wide
More informationHF A 27V Synchronous Buck Converter General Description. Features. Applications. Package: TBD
General Description The is a monolithic synchronous buck regulator. The device integrates 80 mω MOSFETS that provide 4A continuous load current over a wide operating input voltage of 4.5V to 27V. Current
More informationMP2109 Dual 1.2MHz, 800mA Synchronous Step-Down Converter
The Future of Analog IC Technology MP2109 Dual 1.2MHz, 800mA Synchronous Step-Down Converter DESCRIPTION The MP2109 contains two independent 1.2MHz constant frequency, current mode, PWM step-down converters.
More informationMP kHz, 55V Input, 2A High Power LED Driver
The Future of Analog IC Technology MP2488 200kHz, 55V Input, 2A High Power LED Driver DESCRIPTION The MP2488 is a fixed frequency step-down switching regulator to deliver a constant current of up to 2A
More informationMP1496 High-Efficiency, 2A, 16V, 500kHz Synchronous, Step-Down Converter
The Future of Analog IC Technology DESCRIPTION The MP1496 is a high-frequency, synchronous, rectified, step-down, switch-mode converter with built-in power MOSFETs. It offers a very compact solution to
More information36V, 1MHz, 0.6A Step-Down Converter With 35μA Quiescent Current VOUT 3.3V/0.6A
The Future of Analog IC Technology MP4566 36, 1MHz, 0.6A Step-Down Converter With 35μA Quiescent Current DESCRIPTION The MP4566 is a high frequency (1MHz) stepdown switching regulator with integrated internal
More informationELM614BA 2A, 18V, 500kHz, synchronous step down DC/DC converter
General description Maximum absolute ratings ELM614BA is a highfrequency, synchronous, rectified, stepdown, switchmode converter with internal power MOSFETs. It offers a very compact solution to achieve
More informationPin Assignment Pin No. Pin Name Descripition 1 BS High-Side Gate Drive Boost Input. BS supplies the drive for the highside N-Channel MOSFET switch. Co
Description The is a monolithic synchronous buck regulator. The device integrates MOSFETS that provide 2A continuous load current over a wide Operating input voltage of 4.7V to 18V. Current mode control
More informationMP A, 5.5V Synchronous Step-Down Switching Regulator
The Future of Analog IC Technology DESCRIPTION The MP2120 is an internally compensated 1.5MHz fixed frequency PWM synchronous step-down regulator. MP2120 operates from a 2.7V to 5.5V input and generates
More informationMP A, 500KHz Synchronous Rectified Step-up Converter
The Future of Analog IC Technology TM TM MP10 1.A, 00KHz Synchronous Rectified Step-up Converter DESCRIPTION The MP10 is a highly efficient, synchronous, fixed frequency, current-mode step-up converter
More informationNB634 High Effeciency 5A, 24V, 500kHz Synchronous Step-down Converter
The Future of Analog IC Technology NB634 High Effeciency 5A, 24, 500kHz Synchronous Step-down Converter DESCRIPTION The NB634 is a high frequency synchronous rectified step-down switch mode converter with
More informationMP2115 2A Synchronous Step-Down Converter with Programmable Input Current Limit
The Future of Analog IC Technology DESCRIPTION The MP2115 is a high frequency, current mode, PWM step-down converter with integrated input current limit switch. The step-down converter integrates a main
More informationBS SW LSP5522. C4 16nF R3 C5 NC 10K. shows a sample LSP5522 application circuit generating 5V/2A output
Features 2A Output urrent Wide 4.5V to 23V Operating Input Range Integrated Power MOSFET Switches Output Adjustable from 0.925V to 18V Up to 96% Efficiency Programmable Soft-Start Stable with Low ESR eramic
More informationAT V Synchronous Buck Converter
38V Synchronous Buck Converter FEATURES DESCRIPTION Wide 8V to 38V Operating Input Range Integrated two 140mΩ Power MOSFET Switches Feedback Voltage : 220mV Internal Soft-Start / VFB Over Voltage Protection
More information2A, 6V, 1.5MHz, 17μA I Q, COT Synchronous Step Down Switcher In 8-pin TSOT23
The Future of Analog IC Technology DESCRIPTION The MP2161 is a monolithic step-down switch mode converter with built-in internal power MOSFETs. It achieves 2A continuous output current from a 2.5 to 6
More informationEUP A, 30V, 340KHz Synchronous Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit
2A, 30, 340KHz ynchronous tep-down Converter DECRIPTION The is a synchronous current mode buck regulator capable o driving 2A continuous load current with excellent line and load regulation. The can operate
More information2A, 23V, 340KHz Synchronous Step-Down Converter
2A, 23, 340KHz Synchronous Step-Down Converter FP6188 General Description The FP6188 is a synchronous buck regulator with integrated two 0.13Ω power MOSFETs. It achieves 2A continuous output current over
More informationEUP A,40V,200KHz Step-Down Converter
3A,40V,200KHz Step-Down Converter DESCRIPTION The is current mode, step-down switching regulator capable of driving 3A continuous load with excellent line and load regulation. The operates with an input
More informationMP2144 2A, 5.5V, 1.2MHz, 40μA I Q, COT Synchronous Step Down Switcher
The Future of Analog IC Technology MP2144 2A, 5.5, 1.2MHz, 40μA I Q, COT Synchronous Step Down Switcher DESCRIPTION The MP2144 is a monolithic, step-down, switchmode converter with internal power MOSFETs.
More informationGeneral Description BS SW LSP5526. C4 1.6nF R3 C5 NC 10K. shows a sample LSP5526 application circuit generating 5V/2A output
Features 2A Output urrent Wide 4.5V to 23V Operating Input Range Integrated Power MOSFET Switches Output Adjustable from 0.925V to 18V Up to 96% Efficiency Programmable Soft-Start Stable with Low ESR eramic
More information2A,4.5V-21V Input,500kHz Synchronous Step-Down Converter FEATURES GENERAL DESCRIPTION APPLICATIONS TYPICAL APPLICATION
2A,4.5-21 Input,500kHz Synchronous Step-Down Converter FEATURES High Efficiency: Up to 96% 500KHz Frequency Operation 2A Output Current No Schottky Diode Required 4.5 to 21 Input oltage Range 0.8 Reference
More informationADT7351. General Description. Applications. Features. Typical Application Circuit. Oct / Rev0.
General Description The ADT735 is a step-down converter with integrated switching MOSFET. It operates wide input supply voltage range from 4.5 to 28 with 3A continuous output current. It includes current
More informationMP1496S High-Efficiency, 2A, 16V, 500kHz Synchronous, Step-Down Converter
MP1496S High-Efficiency, 2A, 16, 500kHz Synchronous, Step-Down Converter DESCRIPTION The MP1496S is a high-frequency, synchronous, rectified, step-down, switch-mode converter with built-in power MOSFETs.
More informationEUP3484A. 3A, 30V, 340KHz Synchronous Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit
3A, 30, 340KHz ynchronous tep-down Converter DECRIPTION The is a synchronous current mode buck regulator capable o driving 3A continuous load current with excellent line and load regulation. The can operate
More informationAME. 3A, 28V, 340KHz Synchronous Rectified Step-Down Converter AME5268. Features. General Description. Applications. Typical Application
568 General Description The 568 is a fixed frequency monolithic synchronous buck regulator that accepts input voltage from 4.75 to 8. Two NMOS switches with low on-resistance are integrated on the die.
More informationMP A, 24V, 700KHz Step-Down Converter
The Future of Analog IC Technology MP2371 1.8A, 24V, 700KHz Step-Down Converter DESCRIPTION The MP2371 is a monolithic step-down switch mode converter with a built-in internal power MOSFET. It achieves
More informationMP A, 30V, 420kHz Step-Down Converter
The Future of Analog IC Technology DESCRIPTION The MP28490 is a monolithic step-down switch mode converter with a built in internal power MOSFET. It achieves 5A continuous output current over a wide input
More informationMPM V Input, 0.6A Module Synchronous Step-Down Converter with Integrated Inductor DESCRIPTION FEATURES APPLICATIONS
The Future of Analog IC Technology MPM3805 6 Input, 0.6A Module Synchronous Step-Down Converter with Integrated Inductor DESCRIPTION The MPM3805 is a step-down module converter with built-in power MOSFETs
More information1A, 6V, 1.5MHz, 17μA I Q, COT Synchronous Step Down Switcher In 8-pin TSOT23
The Future of Analog IC Technology MP2159 1A, 6, 1.5MHz, 17μA I Q, COT Synchronous Step Down Switcher In 8-pin TSOT23 DESCRIPTION The MP2159 is a monolithic step-down switch mode converter with built-in
More informationMP A, 36V, 700KHz Step-Down Converter with Programmable Output Current Limit
The Future of Analog IC Technology MP2490 1.5A, 36V, 700KHz Step-Down Converter with Programmable Output Current Limit DESCRIPTION The MP2490 is a monolithic step-down switch mode converter with a programmable
More information2A, 20V Synchronous Step-Down Converter DESCRIPTION FEATURES APPLICATIOS TYPICAL APPLICATION. Parameters Subject to Change Without Notice
2A, 20 Synchronous Step-Down Converter P Parameters Subject to Change Without Notice DESCRIPTION The is a current mode monolithic buck voltage converter. Operating with an input range of 4.7-20, the delivers
More informationMP V, 4A Synchronous Step-Down Coverter
MP9151 20, 4A Synchronous Step-Down Coverter DESCRIPTION The MP9151 is a synchronous rectified stepdown switch mode converter with built in internal power MOSFETs. It offers a very compact solution to
More information1.2A, 23V, 1.4MHz Step-Down Converter
1.2A, 23, 1.4MHz Step-Down Converter General Description The is a buck regulator with a built-in internal power MOSFET. It can provide 1.2A continuous output current over a wide input supply range with
More informationLSP A 23V Synchronous Buck Converter. General Description. Features. Applications. LSP5526 Rev of /8/1.
General Description The LSP5526 is a monolithic synchronous buck regulator. The device integrates 95mΩ MOSFETS that provide 2A continuous load current over a wide operating input voltage of 4.5V to 23V.
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD 38V 5A SYNCHRONOUS BUCK CONVERTER DESCRIPTION The UTC UD38501 is a monolithic synchronous buck regulator. The device integrates internal high side and external low side power
More information2A, 23V, 380KHz Step-Down Converter
2A, 23V, 380KHz Step-Down Converter General Description The is a buck regulator with a built-in internal power MOSFET. It achieves 2A continuous output current over a wide input supply range with excellent
More informationEUP A,30V,500KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit
5A,30V,500KHz Step-Down Converter DESCRIPTION The is current mode, step-down switching regulator capable of driving 5A continuous load with excellent line and load regulation. The operates with an input
More informationMP2313 High Efficiency 1A, 24V, 2MHz Synchronous Step Down Converter
The Future of Analog IC Technology MP2313 High Efficiency 1A, 24V, 2MHz Synchronous Step Down Converter DESCRIPTION The MP2313 is a high frequency synchronous rectified step-down switch mode converter
More informationAT7252 2A, 20V Synchronous Step-Down Converter
FEATURES DESCRIPTION 4.5 to 20 input voltage range 2A load current capability Up to 95% efficiency High efficiency at light load Fixed 500KHz Switching frequency Input under voltage lockout Start-up current
More informationMP2225 High-Efficiency, 5A, 18V, 500kHz Synchronous, Step-Down Converter
The Future of Analog IC Technology DESCRIPTION The MP2225 is a high-frequency, synchronous, rectified, step-down, switch-mode converter with built-in power MOSFETs. It offers a very compact solution to
More informationMP8619 8A, 25V, 600kHz Synchronous Step-down Converter
The Future of Analog IC Technology DESCRIPTION The MP8619 is a high frequency synchronous rectified step-down switch mode converter with built in internal power MOSFETs. It offers a very compact solution
More informationMP2482 5A, 30V, 420kHz Step-Down Converter
The Future of Analog IC Technology DESCRIPTION The MP2482 is a monolithic step-down switch mode converter with a built in internal power MOSFET. It achieves 5A continuous output current over a wide input
More informationHM8113B. 3A,4.5V-16V Input,500kHz Synchronous Step-Down Converter FEATURES GENERAL DESCRIPTION APPLICATIONS TYPICAL APPLICATION
3A,4.5-16 Input,500kHz Synchronous Step-Down Converter FEATURES High Efficiency: Up to 96% 500KHz Frequency Operation 3A Output Current No Schottky Diode Required 4.5 to 16 Input oltage Range 0.6 Reference
More informationMP2497-A 3A, 50V, 100kHz Step-Down Converter with Programmable Output OVP Threshold
The Future of Analog IC Technology MP2497-A 3A, 50V, 100kHz Step-Down Converter with Programmable Output OVP Threshold DESCRIPTION The MP2497-A is a monolithic step-down switch mode converter with a programmable
More informationMP3900 High Efficiency Boost Controller
The Future of Analog IC Technology DESCRIPTION The MP3900 is a boost controller that drives an external MOSFET capable of handling 0A current. It has an operational current of typically 80µA and can accommodate
More informationAIC2858 F. 3A 23V Synchronous Step-Down Converter
3A 23V Synchronous Step-Down Converter FEATURES 3A Continuous Output Current Programmable Soft Start 00mΩ Internal Power MOSFET Switches Stable with Low ESR Output Ceramic Capacitors Up to 95% Efficiency
More informationUNISONIC TECHNOLOGIES CO., LTD UD38252
UNISONIC TECHNOLOGIES CO., LTD UD38252 38V SYNCHRONOUS BUCK CONVERTER WITH CC/CV DESCRIPTION UTC UD38252 is a wide input voltage, high efficiency Active CC step-down DC/DC converter that operates in either
More informationMP2105 1MHz, 800mA Synchronous Step-Down Converter
The Future of Analog IC Technology MP2105 1MHz, 800mA Synchronous Step-Down Converter DESCRIPTION The MP2105 is a 1MHz constant frequency, current mode, PWM step-down converter. The device integrates a
More informationMP1530 Triple Output Step-Up Plus Linear Regulators for TFT Bias
The Future of Analog IC Technology MP530 Triple Output Step-Up Plus Linear Regulators for TFT Bias DESCRIPTION The MP530 combines a triple output step-up converter with linear regulators to provide a complete
More informationMP1531 Low Power, Triple Output Step-Up Plus Charge Pump for TFT Bias
The Future of Analog IC Technology DESCRIPTION The MP53 is a triple output step-up converter with charge-pumps to make a complete DC/DC converter to power a TFT LCD panel from a 2.7 to 5.5 supply. The
More informationAT V 5A Synchronous Buck Converter
FEATURES DESCRIPTION Wide 8V to 38V Operating Input Range Integrated 80mΩ Power MOSFET Switches Output Adjustable from VFB(1V) to 20V Up to 95% Efficiency Internal Soft-Start Stable with Low ESR Ceramic
More information3A, 23V, 380KHz Step-Down Converter
3A, 23V, 380KHz Step-Down Converter General Description The is a buck regulator with a built in internal power MOSFET. It achieves 3A continuous output current over a wide input supply range with excellent
More informationMP MHz, 350mA Boost Converter
The Future of Analog IC Technology MP3209 1.4MHz, 350mA Boost Converter DESCRIPTION The MP3209 is a current mode step up converter intended for small, low power applications. The MP3209 switches at 1.4MHz
More informationSPPL12420RH. 2 A Synchronous Rectified Step-Down Converter FEATURES DESCRIPTION RADIATION HARDNESS APPLICATIONS
FEATURES 2 A continuous output current Input voltage capability (derating reference): 24 V Minimum input voltage: 4.5 V Minimum output voltage: 0.923 V Latch-up immune (fully isolated SOI technology) Hermetic
More informationn Application l Notebook Systems and I/O Power l Digital Set Top Boxes l LCD Display, TV l Networking, XDSL Modem n Typical Application VIN 4.
5297 n General Description The 5297 is a high frequency synchronous stepdown DC-DC converter with built internal power MOSFETs. That provides wide 4.5 to 18 input voltage range and 3A continuous load current
More information