S5 (PMR-446) Model Programming software for S5 (PMR-446) Model

Transcription

1 S5 (PMR-446) Model Programming software for S5 (PMR-446) Model PC Program S5 (PMR-446) Model Software Guide Version 1.3 issued on December 15 th 2007 Version 1.3 Page 1

2 CONTENTS 1. Basic Programming Channel Frequency Setting Rx frequency, Rx tone, Tx frequency and Tx tone setting Rx and Tx option setting System Option setting Tone setting Tool Bar Tool Bar mode New Open Save Print Program Exit Menu File Menu Help Menu Version 1.3 Page 2

3 1. Basic Programming 1.1 Channel Frequency Setting Channel frequency cans use only 8 channels [1] Rx frequency, Rx tone, Tx frequency and Tx tone Setting. Double click in table (see1.2). [2] Rx and Tx Option setting. Double click in table (see 1.3) [3] S5 Pc programming Detail. It ll show about information of the model name, maximum of channel pc program and firmware version and when you ve clicked in column on table (Rx Freq. LB column) it ll show the detail of data setting. Version 1.3 Page 3

4 1.2 Rx frequency, Rx tone, Tx frequency and Tx tone Setting When you had double clicked on the line related to the radio channel you need to program it ll show you in this window Rx / Tx Channel Freq >>?? <<. is the number of the channel frequency setting Rx / Tx Freq. is the Frequency setting which have range between MHz (in the table). Model S5 (PMR-446) Frequency Range MHz Auto channel step is set to , , , , , , and When select in Rx / Tx Frequency list box. And Auto Frequency when none frequency selected is set to the Low frequency of S5 (PMR-446) model s range ( MHz) Rx / Tx Tone select None tone is Rx and Tx not use sub tone frequency modulation Ctcss tone has use 49 tone in analog modulation, the range is between Hz. No Ctcss No Ctcss No Ctcss No Ctcss No Ctcss Version 1.3 Page 4

5 DCS and IDCS (Invert DCS) Tone has use 104 tone in digital modulation. No DCS No DCS No DCS No DCS No DCS No DCS None Standard Ctcss#1 and None Standard Ctcss#2 tone frequency. None Standard Ctcss tone s range is Hz, it can change tone frequency by System option setting mode in None standard Ctcss#1-#2 case Button Active Clear Channel Frequency button. Use to clear the frequency data which was setted or the wrong data setting Back Channel Frequency button. Use to call the frequency that you setting before or show the frequency in the lower channel that you were setted into the table Next Channel Frequency button. Use to show the frequency in the upper channel that you were setted into the table Setting button. This button use for setting data into the table.if there aren t Rx or Tx Frequency in text box, program will auto setting to the lowest frequency of S5 Model s band which you d selected in the first time Exit button. Exit button is use for exit from channel setting form. Version 1.3 Page 5

6 1.3 Rx and Tx Option setting Rx-IND It s Individual Tone setting in Rx mode receive only, Step set is OFF Tone1 Tone2 OFF And then use Tone1 and Tone 2 frequency by 2-Tone Setting. OFF : Rx Individual tone disable Tone1 : Rx use Individual tone1 Tone2 : Rx use Individual tone Rx-Grp It s Group tone setting in Rx mode receive only, Step set is ON OFF. ON: Rx Group tone enables OFF: Rx Group tone disable Rx-SGrp. It s Super Group tone setting in Rx mode receive only, Step set is ON OFF. ON: Rx Super Group tone enables OFF: Rx Super Group tone disable User 10 Individual Tone 1 User 8 Individual Tone 2 User 9 User 2 User 3 User 1 Group tone Super group User 6 User 4 User 5 User 7 User 11 Version 1.3 Page 6

7 1.3.4 Power It s Only Tx Power Low (L) transmits. L: Tx power Low transmit Band It s Only Narrow (N) bandwidth N: Narrow band Scan It s Channel scan option enable / disable, Double click to change ON OFF and OFF ON. ON: Channel scan enable OFF: Channel scan disable Pri It s Channel Priority enable/disable, Double click to change ON OFF and OFF ON. It s can only one channel setting. If channel priority disable, all priority channel scan look back (1.3.8) will disable. ON: Channel Priority enables OFF: Channel Priority disables LB It s Priority Channel Scan Look Back enable/disable; Double click to change ON OFF and OFF ON. It s can t set as same as channel priority (1.3.7) setting when channel priority set to enable. If channel priority disable, all of them can t setting, but if channel priority is set to enable, the Priority Channel Scan Look Back can set to enable and disable. ON: Priority Channel Scan enables. OFF: Priority Channel Scan disables Version 1.3 Page 7

8 1.4 System Option setting [1] Options setting 1.1 Busy Ch. Lock is busy channel lock. When busy channel lock use enable, can Marked Idle setting. 1.2 Tx delay is use Tx delay time when transmit. 1.3 Priority look back time. When Priority channel use enable (see 1.3.7), can setting. 1.4 Emergency Key is the function to set Enable/Disable Emergency Key. 1.5 Monitor Key is the function to set Enable/Disable Monitor Key. [2] TOT Time 2.1 TOT time use enable, can tx time out time and tot penalty setting. If TOT time use disable, tx time out time, tot penalty and tot penalty time can t setting. 2.2 TOT penalty use enable, can tot penalty time setting. [3] Power save 3.1 Power save use enable power on time, power off time and power delay time, can setting. But can t setting use disable. [4] Scan 4.1 Scan use enable scan Ch no, scan speed and scan delay, can setting. But can t setting use disable. 4.2 Operation mode is use 2 case Priority channel disable, can use normal scan tx and rx only no tx select Priority channel enable, can use priority scan tx and priority only tx select. [5] Password It s radio password key. 5.1 Password use enables. 1st password key 4th can setting. But can t setting disable. And can set 1st 4th in same password key. [6] 2-Tone Tone receive OK alert use disable or enable Tone receive remind display use enable. Can 2-Tone interval tone setting. [7] Option key assign It is option key can use one key only select. Version 1.3 Page 8

9 [8] Emergency call tx channel 8.1 Emergency call tx channel can use 2 case Emergency call tx channel form current channel tx or Emergency call tx channel form assigned channel tx. Assigned channel tx can select channel in tx channel frequency. [9] None stand ctcss#1-#2 9.1 None standard ctcss#1 and ctcss#2 ranges is Hz. Use for Rx and Tx modulation for none standard ctcss. 9.2 If over range. Auto ctcss 67.0 Hz setting Version 1.3 Page 9

10 1.5 2-Tone setting [1] 2-Tone Individual tone1 For Rx receive only in individual tone1.it can select tone1 or tone 2 for receive in individual tone1 only. And can Individual tone 1 receive data in Rx mode. 1.1 Tone Frequency range is Hz, default 300.0Hz 1.2 Tone Duration range e is ms, default 200 ms 1.3 Gap Time range e is ms,default 200ms If Tone 2 Enable was selected, can set tone 2 in anywhere. [2] 2-Tone Individual tone2 For Rx receive only in individual tone2.it can select tone1 or tone 2 for receive in individual tone2 only. And can Individual tone 1 receive data in Rx mode 2.1 Tone Frequency range is Hz, default 300.0Hz 2.2 Tone Duration range is ms, default 200 ms 2.3 Gap Time range is ms,default 200ms If Tone 2 Enable was selected, can set tone 2 in anywhere. [3] 2-Tone Group tone For Rx receive only in group tone. it can select tone1 or tone 2 for receive in group tone only. And can Individual tone1, Individual tone2 and Group tone receive data in Rx mode. 3.1 Tone Frequency range is Hz, default 300.0Hz 3.2 Tone Duration range is ms, default 200 ms 3.3 Gap Time range is ms,default 200ms If Tone 2 Enable was selected, can set tone 2 in anywhere. Version 1.3 Page 10

11 [4] 2-Tone Super Group tone For Rx receive only in group tone. it can select tone1 or tone 2 for receive in group tone only. And can Individual tone1, Individual tone2, Group tone and Super Group tone receive data in Rx mode. 4.1 Tone Frequency range is Hz, default 300.0Hz 4.2 Tone Duration range is ms, default 200 ms 4.3 Gap Time range is ms,default 200ms If Tone 2 Enable was selected, can set tone 2 in anywhere. [5] 2-Tone Tolerance Rx receive mode can select tolerance in range 1.0% - 5.0% step 0.5 for 2-tone mode. Version 1.3 Page 11

12 2. Tool Bar 2.1 Tool Bar mode [1] New project (see 2.2) [2] Open project (see 2.3) [3] Save project (see 2.4) [4] Print data (see 2.5) [5] Read / Write program (see 2.6) [6] Exit program (see 2.7) 2.2 New It s new project on click. All data will set to default data setting. For model use S5 (PMR-446) the Maximum channel settings is only 8 channels for model setting. 2.3 Open Open project file will use to loading data to programming. For project file is use.bsp format only for S5 Pc Programming file 2.4 Save Save project file will use for save project file in.bsp format to save into the computer. 2.5 Print Print data will use to print Channel Frequency, System Option and 2-Tone data. The total page is 2 pages: Page 1 is Channel Frequency and Page 2 is System Option and 2-Tone data Version 1.3 Page 12

13 2.6 Program In this section have 2 operations: Read and Write. Read is the instruction to read data form radio for radio programming which setted in the first time. Write is the instruction to write data to radio for radio programming which setted in the first time. 1 [1] Comport setting. In the first time must click comport setting for refresh comport. 2 3 [2] Select comport to use in Read / Write program. Select the one port that the data cable was connected (auto comport if you don t had selected was COMPORT1). [3] Error comport setting. It will shown you when you have selected the comport which use in another person or program. If have some problem you can fix it yourself. * Check other program use? * Click refresh comport (see [1] Comport setting) 4 5 [4] Comport setting OK, Show comport select in status. [5] Select Read, Write and Stop button. Version 1.3 Page 13

14 [6] The information of Read and Write program use 1-3 steps. [7] Start Read data form radio button. [8] Start Write data to radio button. [9] Stop Read / Write program. [10] Exit Read / Write process. [11] Read / Write data process. 12 [12] Verify data. For read / write data it ll show message box. If the Read or Write data process is complete it ll show the message box in the two top picture (in red square) but if Read or Write data process isn t complete it ll shown you in message box in the two below pictures, please check you data cable and try to read or write new data radio again (follow in the information (6.)). *Note: While the processing, Read and Write buttons will be disable Exit Program It is the menu to exit when you click it; it ll end of process of the program and shutdown the program. Version 1.3 Page 14

15 3. Menu 3.1 File menu New project (see 2.2) Open project (see 2.3) Save project (see 2.4) Print data (see 2.5) Exit program. 3.2 Help menu Help is the section to open help file, the program use to open must be Adobe Acrobat 5.0 up About is the section is show about information of the software. 1 [1] S5 (PMR-446) PC software version. Version 1.3 Page 15