Application Note 5044

Size: px
Start display at page:

Download "Application Note 5044"

Transcription

1 HBCU-5710R 1000BASE-T Small Form Pluggable Low Voltage (3.3V) Electrical Transceiver over Category 5 Unshielded Twisted Pair Cable Characterization Report Application Note 5044 Summary The Physical Medium Attachment (PMA) electrical characteristics, link segment characteristics and Medium Dependent Interface (MDI) characteristics of HBCU- 5710R have been characterized from case temperature 0 C to +70 C and supply voltage 3.1V to 3.5V. The results show that the HBCU-5710R is compatible with the IEEE 802.3:2000 specifications. Introduction The HBCU-5710R 1000BASE-T SFP electrical transceiver is designed to provide an IEEE compatible link for 1.25 Gb/s applications. It offers full duplex throughput of 1 Gb/s by transporting data over unshielded twisted pair category 5 cable with 5-level PAM (Pulse Amplitude Modulation) signals. The Avago 1000BASE-T module takes signals from both the twisted pair category 5 cable and the SerDes interface. It is intended for use over the case temperature range 0 C to +70 C. This report details the characterization of HBCU-5710R transceivers at case temperatures of 0 C, +25 C and +70 C and at supply voltages of 3.1V, 3.3V and 3.5V. Up to ten transceivers were utilized to collect data at various temperature and voltage combinations. Definition of terms The following acronyms and terms are used in this document. They are explained and defined below: BER Bit Error Rate CAT-5 Category 5 EMI ESD MAC MDI MSA NEXT RD SFP TD Electro-magnetic Interference Electrostatic Discharge Media Access Control Medium Dependent Interface Multi-Source Agreement Near End Crosstalk Receiver Data (output) Small Form Factor Pluggable Transmitter Data (input) Temperature The temperature specified is the HBCU-5710R SFP module case temperature measured on the EMI cage of the SFP evaluation board, unless otherwise specified. Voltage The voltage specified is measured at the 20-pin connector on the SFP evaluation board, which normally is about 0.1 volt lower than that of the power supply itself due to the voltage drop across the inductor of the SFP MSA power supply filter. Link Link test is the measure of BER of the module while transmitting and receiving data over a specified length of CAT- 5 cable. IEEE specification for the link performance is that BER should be less than over 100meter CAT-5 cable. For each link test, approximately 30 million packets (or about 20 billion bits) were sent. And several parameters were varied during link testing. They include temperature, voltage, cable length, packet size, utilization rate, input TD amplitude, and supply noise. Channel BER channel is defined as in IEEE 802.3:2000 clause The test channel consists of a 1.2m 120ohm CAT-5 cable followed by a 103m 100ohm CAT-5 cable, then a 1.48m 120ohm CAT-5 cable, and lastly a 4m 100ohm CAT-5 cable. The specification is BER over 100m. Supply Current and Power Dissipation This is the current supplied to and the power dissipated by the module at the relevant supply voltage. They are measured under link up condition. Differential Output Templates The templates are described in IEEE 802.3:2000, section As a module was configured to be in test mode 1 as described in IEEE 802.3:2000, section , the differential output voltage waveform around points A, B, C, D, F and H for each of the four module cable-side channels was tested for compliance to the templates.

2 Peak Differential Output Voltage and Level Accuracy As a module was configured to be in test mode 1 as described in IEEE 802.3:2000, section , this is the test for compliance of the peak differential output voltages at points A, B, C and D for each of the four module cable-side channels to IEEE 802.3:2000, section The disturbing voltage described in IEEE 802.3:2000, section , was not used. Previous measurements have demonstrated that the disturbing voltage has no effect on the peak differential output voltage and level accuracy measurements. Maximum Output Droop As a module was configured to be in test mode 1, this is the test for compliance of the magnitude of the peak output voltages at points G and J as compared to that at points F and H, respectively, per IEEE 802.3:2000, section All four cable-side channels were tested on each module. The disturbing voltage described in IEEE 802.3:2000, section , was not used. Previous measurements have demonstrated that the disturbing voltage has no effect on the droop measurements. Transmitter Distortion When a module is in test mode 4, this is the peak distortion on the differential signal output at the MDI as defined in IEEE 802.3:2000, section Transmitter Timing Jitter There are six parts to the transmitter timing jitter per IEEE 802.3:2000, section The first two are the output jitters for each channel relative to the master TX_TCLK when a module is in test mode 2 or test mode 3. For the next four, the module was linked up to a golden unit with a test channel. While the module is in master and slave modes, the unfiltered and filtered jitter of TX_TCLK was measured with reference to an external master 25 MHz clock. Common Mode Output Voltage The magnitude of the total common-mode output voltage on any transmit circuit as measured per IEEE 802.3:2000, section Modules were configured to be in test mode 4. Common Mode Noise Rejection This is a measurement of a module s ability to withstand common-mode noise from the cabling system generally as a result of electromagnetic field subjection. Modules were tested per IEEE 802.3:2000, section The result is shown via link BER. Alien Crosstalk Noise Rejection This is a measurement of a module s ability to withstand alien crosstalk that simulates a 100BASE-TX noise signal coupled into each individual channel on the CAT-5 cable. The level of the noise signal is 25 mv. Modules were tested per IEEE 802.3:2000, section NEXT Noise Rejection This is a measurement of a module s ability to withstand crosstalk at the near end of a link segment, injected using a PCB that allows for an RC connection between each channel. Modules were tested per IEEE 802.3:2000, section with result shown via link BER. MDI Impedance Balance This is a measurement of the impedance difference between the two MDI contacts to ground of each channel of a module. Modules were tested per IEEE 802.3:2000, section ing was repeated with the module in idle and test mode 4. Transmitter Clock Frequency This is the transmitter clock frequency as tested per IEEE 802.3:2000, section Modules were configured to be in test mode 2. Receiver Frequency Tolerance This is a measurement of the module s ability to properly receive incoming data over a frequency variation as specified per IEEE 802.3:2000, section The frequency variation applied here was +/- 0.04% as compared to the specification of +/- 0.01%. Link BER was measured. MAC-side Frequency Tolerance This is a measurement of the module s tolerance to the frequency variation in the data going from the MAC to the module TD+/- lines as expressed in link BER. Link Delay Skew Tolerance This is a measurement of a module s tolerance to the difference in propagation delay, or skew, between all duplex channel pair combinations of a link segment, as determined by the link BER. Link delay skew tolerance was tested with module pairs. Each pair of modules was connected with a modified 103meter Cat5 cable, in which channel 2 (twist pair 4 and 5) had an extra delay of 63ns. This is beyond the IEEE specification in 802.3:2000 section , which is to tolerate 50ns delay skew with at most 10ns variation over environment.

3 MDI Crossover This is a measurement of the module s ability to automatically identify a crossover cable per IEEE 802.3:2000, sections and A crossover patch cable was inserted in addition to a non-crossover link cable between a pair of modules. The result is shown via link BER. MDI Fault Tolerance This is a test to determine a module s ability to withstand, without damage, any short circuit applied to any set of wires on the cable-side as per IEEE 802.3:2000, section The various combinations of shorts were applied for 1 minute each. Normal operation was verified after the shorts were removed. Normal operation was considered to be error-free operation during a transmission of 30 million packets with random data and packet length and 100% utilization over 116m CAT-5 cable. MDI Return Loss This is a measurement of the attenuation of the differential signal reflection looking into the module from the cable-side as described in IEEE 802.3:2000, section Modules were configured to be in test mode 4. In-Rush Current In-rush current is the initial peak supply current drawn by the module when the module was hot-plugged into a port. This current was measured through a 1.2 ohm sense resistor placed in series with the VCC. The SFP MSA allows a peak of 30mA above the steady state current. RD+/- Amplitude This is the differential RD+/- output voltage amplitude. It can be configured to its lowest and highest states, outside of the nominal state, through register writes. In its nominal state, the module is configured to output approximately mv. The output amplitude for all three states was measured. RD+/- Rise/Fall Times This is the 20% to 80% rise and fall transition times for RD+/- outputs. They were measured with the RD+/- differential output amplitude configured to its nominal, lowest and highest states. Initialization Time Initialization time is the time from power-up until the module begins auto-negotiation with the host system. Reset Assert Time Reset assert time is the time from asserting TX_DISABLE until the module stops sending data or idle pattern to the host system on RD+/-. Reset Negate Time Reset negate time is the time from negating TX_DISABLE until the module begins auto-negotiation with the host system. Radiated Immunity Applying IEC , this is a measurement of a module s ability to withstand a radiated field of magnitude 10V/m, modulated by 80% at 1 khz, and of frequency MHz. This test is done in a GTEM cell. During which time, data with random length, random packet size and 100% utilization rate were sent to and received from the module over a 103m cable. The BER of the module was monitored. Electrostatic Discharge (ESD) to RJ45 This is a test of tolerance for electrostatic discharge to the RJ45 connector receptacle as per variation of IEC NSG-435 model ESD gun was used to apply 40 consecutive pulse discharges, at the rate of one pulse per second. The measure of tolerance is a link recovery after removal of the electrical pulse. Data transmission is with 125 byte packet and 90% utilization rate. Isolation (Hi-Pot) This is the electrical isolation between the port device circuits, including frame ground and all MDI leads. Measure of compliance is described in IEEE 802.3:2000, section MOD_DEF2 Output Levels The measured voltage referenced to ground at the MOD_ DEF2 output for both 1 and 0 states. RX_LOS Output Levels from PHY The measured voltage referenced to ground at the RX_ LOS output for both 1 and 0 states. This is for modules with RX_LOS enabled only. Modules with disabled RX_ LOS has the RX_LOS output tied to ground internally. Note: The following applies to all the tables here after. OT (Over Temperature) = 0/25/70 C; OV (Over Voltage) = 3.1/3.3/3.5 V; OP (Over Packet Size) = 64/125/255/512/1024 byte; OA (Over Differential TD Amplitude) = 0.4/0.8/2.4 V 3

4 Table 1. Link BER Link BER With Extreme TD Voltages Link BER With Supply Noise - 10Hz To 2MHz 70C, 3.3V, 120m, OP, 100% Utilization 70C, 3.3V, 120m, OP, 50% Utilization 70C, 3.3V, 120m, OP, 10% Utilization 70C, 3.3V, 116m, OP, 10% Utilization 70C, 3.3V, 103m, OP 10% Utilization 70C, 3.1V, 116m, 100% Utilization, 430mV/2500mV TD Voltages 70C, 3.1V, 120m, 100% Utilization, 200mV Supply Noise 70C, 3.1V, 116m, 100% Utilization, 200mV Supply Noise 70C, 3.1V, 116m, 10% Utilization, 200mV Supply Noise 2 7.8E E-10 ** E-10 ** 2 1.5E E-12* 10 1E-11* 3 1.2E-10 ** 1 5E-12* 1 5E-12 * No error detected. Error rate calculated with presumed error of 1. ** condition exceeding standard requirement.

5 Table 2. Supply Current and Power Dissipation Differential Output Templates (Points A, B, C, D, F, H) Peak Differential Output Voltage And Level Accuracy OT, OV, OA, 115m, (a) At 0C, 3.5V, Min TD input (b) At 70C, 3.1V, Max TD input (c) At 70C, 3.3V, Nominal TD input 10 ma/ W 276/ 0.97(a) 308/ 1.07(c) 364/ 1.13(b) OT, OV 10 Pass Pass - Point A voltage OT, OV 10 V Absolute value of Point B voltage Relative to Point A - Point C voltage relative to one-half the average of Point A and B (absolute value) voltages - Point D voltage relative to one-half the average of Point A and B (absolute value) voltages Maximum Output Droop - Amplitude at Point G relative to Point F - Amplitude at Point J relative to Point H 370/ C, 3.3V 8 % *** 2*** OT, OV 10 % OT, OV 10 % OT, OV 10 % OT, OV 10 % Transmitter Distortion 70C, 3.1V 3 mv **** *** The IEEE specification for this test is ±1%. The HBCU-5710R achieves ±2% at 25 C, 3.3V. Link degradation has not been observed due to this loosening of the specification. **** The IEEE specification for this test is 10mV. However, the distortion of the test system is about 10mV. The modules were considered to pass the specification if the measured transmitter distortion value is less than 18mV. 5

6 Table 3. - TX Output Jitter 1: 70C, 3.1V, Mode 2 2: 70C, 3.1V, Mode 3 - TX_TCLK Jitter 3: 70C, 3.1V, Master TX_TCLK referenced to 25MHz external clock Common Mode Output Voltage Common Mode Noise Rejection Alien Crosstalk Noise Rejection Near End Crosstalk (NEXT) Noise Rejection MDI Impedance Balance Transmitter Clock Frequency Relative to 125MHz ( 4: Same as 3 but filtered) 5: 70C, 3.1V, recovered TX_TCLK referenced to 25MHz external clock ( 6: Same as 5 but filtered) 3 ps ps ps ps ps ps C, 3.3V 10 mv C, 3.1V, 100m, 100% Utilization, 2.8V Common Mode Voltage over frequency range of 1-250MHz OT, OV, 103m, 100% Utilization OT, OV, 103m, 100% Utilization 3 5.4E E-12* 10 5E-12* 70C, 3.1V 3 pass pass OT, 3.3V 10 %

7 Table 4. MAC-side Frequency Tolerance Link Delay Skew Tolerance 70C, 3.1V, 116m, 64-byte Frame, 10B-encoded 1010 Pattern, 90% Utilization, +/- 0.01% Data Rate Variaton 70C, 3.1V, 103m, 90% Utilization MDI Crossover 25C, 3.3V, 116m, 100% Utilization MDI Fault Tolerance with Short s 1a) Ch (0,1)+ b) Ch (2,3)+ 2a) Ch (0,1)- b) Ch (2,3)- 3a) Ch (0,1,2,3)+ b) Ch (0,1,2,3)- 3 1E-11* 3 6.3E E-12* 3 Error free after fault removal 4uA with fault MDI Return Loss OT, OV 10 pass pass Error free Transmission after fault removal 300mA with fault In-Rush Current OT, 3.3V 3 ma (30mA above link up steady state max current of around 300mA) RD+/- Differential Amplitude - Nominal output config OT, OV 10 mv Low output config OT, OV 10 mv High output config OT, OV 10 mv

8 Table 5. - Nominal output configuration - Low output configuration - High output configuration OT, OV 10 ps 91/95 107/ / OT, OV 10 ps 92/91 108/ / OT, OV 10 ps 93/99 107/ / Initialization Time 25C, 3.3V 10 ms Reset Assert Time 25C, 3.3V 10 us Reset Negate Time 25C, 3.3V 10 ms Radiated Immunity 25C, 3.3V, 103m, 10V/m field ranging 80MHz to 1GHz Electrostatic Discharge (ESD) to RJ45 3 Error Free Inside switch box 2 kv 8 8 Isolation (Hi-Pot) 25C, 3.3V 200 ua pass 2.25kV DC for 60s MOD_DEF2 Output Levels - Voh OT, 3.3V 3 V Vol OT, 3.3V 3 V RX_LOS Output Levels from PHY ***** - Voh OT, 3.3V 3 V Vol OT, 3.3V 3 V ***** This is valid only for modules with RX_LOS enabled. Modules with disabled RX_LOS has the RX_LOS output tied to ground internally. For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. Data subject to change. Copyright 2007 Avago Technologies Limited. All rights reserved EN - May 28, 2007

FCOPPER-SFP BASE-TX Copper SFP Transceiver

FCOPPER-SFP BASE-TX Copper SFP Transceiver 100BASE-TX Copper SFP Transceiver March 27, 2012 Product Overview The electrical Small Form Factor Pluggable (SFP) transceiver module is specifically designed for converting 100BASE-FX NRZI port interface

More information

SFP Cooper 1000Base-T 100M SL-SFP-3T-XX

SFP Cooper 1000Base-T 100M SL-SFP-3T-XX SFP Cooper 1000Base-T 100M SL-SFP-3T-XX Overview Sourcelight SL-SFP-3T-XX Copper Small Form Pluggable (SFP) transceiver is high performance, cost effective module compliant with the Gigabit Ethernet and

More information

SFP- GE- RJ45- AO. 1.25Gbps SFP Copper Transceiver

SFP- GE- RJ45- AO. 1.25Gbps SFP Copper Transceiver SFP- GE- RJ45- AO ZTE 1000BASE- TX SFP COPPER 100M REACH RJ- 45 SFP- GE- RJ45- AO 1.25Gbps SFP Copper Transceiver Features Up to 1.25Gb/s bi- directional data links Hot- pluggable SFP footprint Extended

More information

1000BASE-T SFP Copper Transceiver Hot Pluggable, Cat-5 UTP Cable, 100m

1000BASE-T SFP Copper Transceiver Hot Pluggable, Cat-5 UTP Cable, 100m Mini-GBIC Module INEO-MD-MSFP-TE 1000BASE-T SFP Copper Transceiver Hot Pluggable, Cat-5 UTP Cable, 100m tactio TM s INEO-MD-MSFP-TE 1000BASE-T copper SFP transceiver is high performance, cost effective

More information

1000BASE-T Copper SFP Transceiver

1000BASE-T Copper SFP Transceiver 1000BASE-T Copper SFP Transceiver Features: Operating data rate up to 1.25 Gbps Compact RJ-45 connector assembly Single 3.3V power supply and Low power dissipation Hot Pluggable 1000 BASE-T operation in

More information

1000BASE-T Copper SFP Transceiver

1000BASE-T Copper SFP Transceiver PRODUCT FEATURES Up to 1.25 Gb/s bi-directional data links Hot-pluggable SFP footprint Low power dissipation(1.05w typical) Compact RJ-45 assembly Fully metal enclosure, for lower EMI RoHS compliant and

More information

407-BBOS-A 407-BBOS-A. Features. Up to 1.25Gb/s bi-directional data links. Hot-pluggable SFP footprint

407-BBOS-A 407-BBOS-A. Features. Up to 1.25Gb/s bi-directional data links. Hot-pluggable SFP footprint 1000BASE, SFP-T Transceiver Features Up to 1.25Gb/s bi-directional data links Hot-pluggable SFP footprint Commercial case temperature range (0 C to +70 C ) Fully metallic enclosure for low EMI Low power

More information

SNR-SFP100-T. SNR-SFP100-T 10/100M Copper SFP Series

SNR-SFP100-T. SNR-SFP100-T 10/100M Copper SFP Series SNR-SFP100-T 10/100M Copper SFP Series 10/100BASE-T Copper SFP Transceiver RoHS6 Compliant Features Support 10/100BASE-T Operation in Host Systems For 100m Reach over Cat 5 UTP Cable Hot-Pluggable SFP

More information

SFP-SW10100-R-TP 10/100/1000 BASE-T Copper SFP Transceiver

SFP-SW10100-R-TP 10/100/1000 BASE-T Copper SFP Transceiver SFP-SW10100-R-TP 10/100/1000 BASE-T Copper SFP Transceiver PRODUCT FEATURES Up to 1.25 Gb/s bi-directional data links Hot-pluggable SFP footprint Low power dissipation(1.05w typical) Compact RJ-45 assembly

More information

1000BASE-T Copper SFP Transceiver

1000BASE-T Copper SFP Transceiver 000BASE-T Copper SFP Transceiver Product Overview STC-0003 000BASE-T Copper Small Form Pluggable (SFP) transceivers are based on the SFP Multi Source Agreement (MSA). They are compatible with the Gigabit

More information

1.25Gb/s 160km DWDM SFP Transceiver (OP340GD-D ) Hot Pluggable, Duplex LC, 100GHz, DWDM DFB & APD, Single-mode, DDM

1.25Gb/s 160km DWDM SFP Transceiver (OP340GD-D ) Hot Pluggable, Duplex LC, 100GHz, DWDM DFB & APD, Single-mode, DDM DWDM 100GHz ITU Grid C Band Available DWDM DFB laser transmitter APD receiver Single +3.3V Power Supply Monitoring Interface Compliant with SFF-8472 Low power dissipation

More information

PROLABS GLC-T-C 1000BASE-T SFP (Small Form Pluggable) Copper Transceiver 3.3V, 1.25GBd Gigabit Ethernet

PROLABS GLC-T-C 1000BASE-T SFP (Small Form Pluggable) Copper Transceiver 3.3V, 1.25GBd Gigabit Ethernet PROLABS GLC-T-C 1000BASE-T SFP (Small Form Pluggable) Copper Transceiver 3.3V, 1.25GBd Gigabit Ethernet GLC-T-C Overview PROLABS s GLC-T-C Copper SFP transceivers are based on Gigabit Ethernet IEEE 802.3

More information

TS-SF-T BASE-T Copper SFP Transceiver

TS-SF-T BASE-T Copper SFP Transceiver PRODUCT FEATURES Up to 1.25 Gb/s bi-directional data links Hot-pluggable SFP footprint Low power dissipation(1.05w typical) Compact RJ-45 assembly Fully metal enclosure, for lower EMI RoHS compliant and

More information

SFP+ Copper 10GBase-T SL-SFP-10G-T

SFP+ Copper 10GBase-T SL-SFP-10G-T SFP+ Copper 10GBase-T SL-SFP-10G-T Overview SFP+ 10G copper transceiver module is a high performance integrated duplex data link for bi-directional communication over copper cable. It is specifically designed

More information

4.25Gbps SFP Transceiver

4.25Gbps SFP Transceiver 4.25Gbps SFP Transceiver Features Operating data rate up to 4.25Gbps 1310 nm DFB LD Transmitter Distance up to 30km Single 3. 3V Power supply and TTL Logic Interface Duplex LC Connector Interface Hot Pluggable

More information

RoHS Compliant Small Form Factor Pluggable Transceiver for Gigabit Ethernet and Fiber Channel

RoHS Compliant Small Form Factor Pluggable Transceiver for Gigabit Ethernet and Fiber Channel RoHS Compliant Small Form Factor Pluggable Transceiver for Gigabit Ethernet and Fiber Channel FEATURES Compliant with SFP Transceiver MSA specification Compliant with Specifications for IEEE 802.3z/Gigabit

More information

SFP+ Series SFP-10G-SR

SFP+ Series SFP-10G-SR SFP-10G-SR 850nm SFP+ Multi-Mode Transceiver, With Diagnostic Monitoring 10G BASE-SW/SR Duplex SFP+ Transceiver, RoHS 6 Compliant Features Operating data rate up to 10.3Gbps 850nm VCSEL Distance up to

More information

10GBASE-T Copper SFP+ Transceiver SFP+-10GBASE-T

10GBASE-T Copper SFP+ Transceiver SFP+-10GBASE-T 10GBASE-T Copper SFP+ Transceiver SFP+-10GBASE-T 1.PRODUCT FEATURES Support 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T Hot-pluggable SFP footprint Compact RJ-45 connector assembly RoHS compliant and

More information

2.5Gbps SFP Transceiver

2.5Gbps SFP Transceiver 2.5Gbps SFP Transceiver Features Operating data rate up to 2.5Gbps 850nm VCSEL Laser Transmitter 300m with 50/125 µm MMF, 150m on 62.5/125 µm MMF Single 3. 3V Power supply and TTL Logic Interface Duplex

More information

SFP Series IOLS-1348-XXXX. 4.25Gbps up to 30 km transmission. version 0.1 FEATURES PRODUCT DESCRIPTION

SFP Series IOLS-1348-XXXX. 4.25Gbps up to 30 km transmission. version 0.1 FEATURES PRODUCT DESCRIPTION up to 30 km transmission FEATURES OPERATING DATA RATE UP TO 1310 nm LD TRANSMITTER Features DISTANCE UP TO 30 KM SINGLE 3.3V POWER SUPPLY AND TTL LOGIC INTERFACE DUPLEX LC CONNECTOR INTERFACE Description

More information

GLC-SX-MMD-SO SFP, 1G, 550m, Multi Mode, 850nm, with DOM

GLC-SX-MMD-SO SFP, 1G, 550m, Multi Mode, 850nm, with DOM General Description The 1G SFP optical transceivers are designed for Storage, IP network and LAN. It is a fully integrated 1 Gbps optical transceiver module. This module is designed for multimode fiber

More information

OCTECH 1.25Gbps SFP Transceiver

OCTECH 1.25Gbps SFP Transceiver 10 May, 2011 OCTECH 1.25Gbps SFP Transceiver Description The GLC-LH-SM-OC single mode transceiver is a small form factor pluggable module for bi-directional serial optical data communications such as Gigabit

More information

Optical Transceiver Module - SFP

Optical Transceiver Module - SFP Optical Transceiver Module - SFP KOLS-8524 850nm Multi-mode SFP Transceiver, 1~2.125Gbps, with Digital Diagnostic Function Features Compliant with SFP Transceiver SFF-8472 MSA specification with internal

More information

GLC-SX-MM-LEG. 1.25Gbps SFP Transceiver

GLC-SX-MM-LEG. 1.25Gbps SFP Transceiver GLC-SX-MM-LEG CISCO 1000BASE-SX SFP MMF 850NM 550M REACH LC GLC-SX-MM-LEG 1.25Gbps SFP Transceiver Features Up to 1.25Gb/s data links Duplex LC connector Hot-pluggable SFP footprint 850nm VCSEL Laser transmitter

More information

GLC-LH-SMD-SO SFP, 1G, 10km, Single Mode, 1310nm, with DOM

GLC-LH-SMD-SO SFP, 1G, 10km, Single Mode, 1310nm, with DOM General Description The 1G SFP optical transceivers are designed for Storage, IP network and LAN. It is a fully integrated 1 Gbps optical transceiver module. This module is designed for Single mode fiber

More information

1000BASE-T Copper Transceiver Small Form Pluggable (SFP), 3.3V 1.25Gbps Gigabit Ethernet. Features

1000BASE-T Copper Transceiver Small Form Pluggable (SFP), 3.3V 1.25Gbps Gigabit Ethernet. Features Features Hot-pluggable SFP Footprint Fully Metallic Enclosure for Low EMI Low Power Dissipation Compact RJ-45 Connector Assembly Detailed Product Information in EEPROM +3.3V Single Power Supply Access

More information

SFP Dual LC 1.25G SMF 20Km 1310nm Transceiver. Features. Applications. Ordering Information APPLIED OPTOELECTRONICS, INC.

SFP Dual LC 1.25G SMF 20Km 1310nm Transceiver. Features. Applications. Ordering Information APPLIED OPTOELECTRONICS, INC. Features Applications Gigabit Ethernet (1.25Gbps) Fiber Channel 1xFC (1.0625Gbps) SFP Type Dual LC Transceiver 1310nm FP Laser PIN Photo Detector 20Km transmission with SMF 3.3V single power supply Compliant

More information

GLC-LH-SM-LEG-5PK. 1.25Gbps SFP Transceiver

GLC-LH-SM-LEG-5PK. 1.25Gbps SFP Transceiver 39508 GLC-LH-SM-LEG-5PK CISCO 1000BASE-LX SFP SMF 1310NM 10KM REACH LC GLC-LH-SM-LEG-5PK 1.25Gbps SFP Transceiver Features Up to 1.25Gb/s data links Duplex LC connector Hot-pluggable SFP footprint 1310nm

More information

Product Specification

Product Specification SFP-10GTX 10GBASE T SFP+ Copper Transceiver Features Support 10Gbase T / 5Gbase T / 2.5Gbase T / 1000base T Hot pluggable SFP footprint Compact RJ 45 connector assembly RoHS compliant and lead free Single

More information

Features: Compliance: Applications. Warranty: AH-ACC-SFP-1G-T-GT Gigabit Ethernet SFP Module TX 10/100/1000Mbps Aerohive Compatible

Features: Compliance: Applications. Warranty: AH-ACC-SFP-1G-T-GT Gigabit Ethernet SFP Module TX 10/100/1000Mbps Aerohive Compatible The GigaTech Products is programmed to be fully compatible and functional with all intended AEROHIVE switching devices. This SFP module is based on the Gigabit Ethernet IEEE 802.3 and 1000Base-T standard

More information

SFP CWDM 1G 120km LC datasheet A-GEAR World Wide Manufacturing Product Specification

SFP CWDM 1G 120km LC datasheet A-GEAR World Wide Manufacturing Product Specification Product Specification 1.25Gb/s CWDM Single-mode SFP Transceiver 1. Product Features Up to 1.25Gb/s data links The DFB laser transmitter APD receiver Up to 120km on 9/125μm SMF Hot-pluggable SFP footprint

More information

AA E6-A AA E6-A. Features. Up to 1.25Gb/s Data Links. Hot-Pluggable. Duplex LC connector. Up to 10km on 9/125μm SMF

AA E6-A AA E6-A. Features. Up to 1.25Gb/s Data Links. Hot-Pluggable. Duplex LC connector. Up to 10km on 9/125μm SMF 1GBASE, SFP, LX Transceiver Features Up to 1.25Gb/s Data Links Hot-Pluggable Duplex LC connector Up to 10km on 9/125μm SMF 1310nm FP laser transmitter Single +3.3V Power Supply Monitoring Interface Compliant

More information

JD061A-C. 1.25Gbps SFP Transceiver

JD061A-C. 1.25Gbps SFP Transceiver JD061A-C HP 1000Base-EX SFP SMF 1310nm, 40km Reach, LC JD061A-C 1.25Gbps SFP Transceiver Features Up to 1.25Gb/s data links Duplex LC connector Hot-pluggable SFP footprint 1310nm FP Laser transmitter RoHS

More information

1.25Gbps SFP Optical Transceiver, 80KM Reach

1.25Gbps SFP Optical Transceiver, 80KM Reach 1.25Gbps SFP Optical Transceiver, 80KM Reach Model: JFS5512-3LCD80 Size (mm): 56.6x14.8x12.4 Features Data-rate of 1.25Gbps operation 1550nm DFB laser and PIN photo detector for 80KM transmission Compliant

More information

SFP+ BIDI Series GigaStream BIDI-10G-SFP-40A & BIDI-10G-SFP-40B

SFP+ BIDI Series GigaStream BIDI-10G-SFP-40A & BIDI-10G-SFP-40B GigaStream BIDI-10G-SFP-40A & BIDI-10G-SFP-40B Tx: 1270nm/Rx: 1330nm BIDI SFP+ Transceiver for 10GbE Tx: 1330nm/Rx: 1270nm BIDI SFP+ Transceiver for 10GbE RoHS 6 Compliant Features Operating data rate

More information

PRODUCT FEATURES APPLICATIONS. Pin Assignment: 1 Gigabit Long-Wavelength SFP Transceiver SFP-SX-MM

PRODUCT FEATURES APPLICATIONS. Pin Assignment: 1 Gigabit Long-Wavelength SFP Transceiver SFP-SX-MM 1 Gigabit Long-Wavelength SFP Transceiver SFP-SX-MM PRODUCT FEATURES Up to 1.25Gb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic functions 850nm VCSEL laser transmitter

More information

XFP Series JD1310-XFP-LC.S10. Features. Applications. Ordering information

XFP Series JD1310-XFP-LC.S10. Features. Applications. Ordering information JD1310-XFP-LC.S10 1310nm XFP single-mode for 10GbE/10GFC/SDH/SONET Duplex XFP Transceiver RoHS6 Compliant XFP Series Features Supports 9.95Gb/s to 11.3Gb/s bit rates Hot-pluggable XFP footprint Link length

More information

SO-SFP-100Base-T. SFP, 125Mbps FE to 10/100Base-T convert SO-SFP-100BASE-T OVERVIEW PRODUCT FEATURES APPLICATIONS ORDERING INFORMATION DATASHEET 4.

SO-SFP-100Base-T. SFP, 125Mbps FE to 10/100Base-T convert SO-SFP-100BASE-T OVERVIEW PRODUCT FEATURES APPLICATIONS ORDERING INFORMATION DATASHEET 4. SO-SFP-100BASE-T SFP, 125Mbps FE to 10/100Base-T convert SO-SFP-100BASE-T OVERVIEW The SO-SFP-100Base-T is a single-mode transceiver in small form-factor pluggable module for duplex optical data communications.

More information

GLC-GE-100FX-LEG. 155Mbps SFP Transceiver

GLC-GE-100FX-LEG. 155Mbps SFP Transceiver 39500 GLC-GE-100FX-LEG CISCO 100BASE-FX SFP MMF 1310NM 2KM REACH LC DOM GLC-GE-100FX-LEG 155Mbps SFP Transceiver Features Operating Data Rate up to 155Mbps 1310 FP Laser transmitter 2km with 50/125 μm

More information

TPP3XGDS0x000E2G 850nm SFP+ Transceiver

TPP3XGDS0x000E2G 850nm SFP+ Transceiver Features 850nm VCSEL laser TPP3XGDS0x000E2G Transmission distance up to 300m on OM3 MM fiber Low power consumption Wide Case Operating Temperature Range Compliant with SFP+ Electrical MSA SFF-843 Compliant

More information

Product Specification. Short-Wavelength Pluggable SFP Transceiver FTRJ D

Product Specification. Short-Wavelength Pluggable SFP Transceiver FTRJ D Product Specification Short-Wavelength Pluggable SFP Transceiver FTRJ-8519-7D PRODUCT FEATURES Up to 1.25 Gb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic functions

More information

EOLS-1312-XXXX 1.25Gbps SFP Transceiver

EOLS-1312-XXXX 1.25Gbps SFP Transceiver S Series EOLS-1312-XXXX S Transceiver Features Operating data rate up to 1310 nm LD Transmitter Distance up to 30km Single 3. 3V Power supply and TTL Logic Interface Duplex LC Connector Interface Hot Pluggable

More information

OCTECH 1.25Gbps SFP Transceiver

OCTECH 1.25Gbps SFP Transceiver 10 May, 2011 OCTECH 1.25Gbps SFP Transceiver Description The OC-125G-S5S multi-mode transceiver is a small form factor pluggable module for bi-directional serial optical data communications such as Gigabit

More information

GLC-LH-SM-TX. Product Features. Applications. General. Cisco Compatible 1000BASE-LX/LH SFP TurboX

GLC-LH-SM-TX. Product Features. Applications. General. Cisco Compatible 1000BASE-LX/LH SFP TurboX Product Features Up to 1.25Gb/s data links Duplex LC connector Hot-pluggable SFP footprint 1310nm FP laser transmitter RoHS compliant and Lead Free Up to 10km on 9/125um SMF Metal enclosure for lower EMI

More information

APSB53123xxL20. Product Features. Applications. General. 1.25Gb/s BiDi SFP Transceiver

APSB53123xxL20. Product Features. Applications. General. 1.25Gb/s BiDi SFP Transceiver Up to 1.25Gb/s data links Single LC connector Hot-pluggable SFP footprint 1550nm DFB laser transmitter 1310nm InGaAs PIN receiver RoHS compliant and Lead Free Up to 20km on 9/125um SMF Metal enclosure

More information

Features. RX Sensitivity (dbm) TX Power (dbm) Voltage (V) SFP-Dual-LC 1.25G MMF 2Km ~ -9 < AC/AC TTL N -5 ~ +70 A56L-BN13-A6MA

Features. RX Sensitivity (dbm) TX Power (dbm) Voltage (V) SFP-Dual-LC 1.25G MMF 2Km ~ -9 < AC/AC TTL N -5 ~ +70 A56L-BN13-A6MA Features Applications Gigabit Ethernet (1.25Gbps) Fiber Channel 1xFC (1.0625Gbps) Add Application item: CPRI 2 (1228.8 Mbit/s) only for Temp spec -40~85 SFP Type Dual LC Transceiver 1310nm FP Laser PIN

More information

SFP-1000BASE-LX-LEG. 1.25Gbps SFP Transceiver

SFP-1000BASE-LX-LEG. 1.25Gbps SFP Transceiver SFP-1000BASE-LX-LEG 1000BASE-LX SFP SMF 1310NM 10KM REACH LC DOM SFP-1000BASE-LX-LEG 1.25Gbps SFP Transceiver Features Up to 1.25Gb/s data links Duplex LC connector Hot-pluggable SFP footprint 1310nm FP

More information

PRE-SFP-OC Gb/s Transceiver, 1310 nm, 15 km (IR1), DDM

PRE-SFP-OC Gb/s Transceiver, 1310 nm, 15 km (IR1), DDM Product Features Up to 2.67Gb/s Data Links Hot-Pluggable 1310nm DFB laser transmitter and PIN receiver Duplex LC connector RoHS compliant and Lead Free Up to 15 km on 9/125 µm SMF Single +3.3V Power Supply

More information

GE-PON OLT Transceiver 1.25Gbps Upstream/1.25Gbps Downstream

GE-PON OLT Transceiver 1.25Gbps Upstream/1.25Gbps Downstream GE-PON OLT Transceiver 1.25Gbps Upstream/1.25Gbps Downstream PRODUCT FEATURES Bi-directional 1.25Gbps Upstream/1.25Gbps Downstream Complies with IEEE802. 3ah 1000Base-PX20 application SFP package with

More information

10Gb/s DWDM Single-mode SFP+ Transceiver

10Gb/s DWDM Single-mode SFP+ Transceiver Product Specification SFP+ DWDM 10G-ER 40km LC 10Gb/s DWDM Single-mode SFP+ Transceiver 1. Product Features Duplex LC connector Compliant with SFP+ MSA Compliant to 802.3ae 10GBASE-ER Compliant to SFP+

More information

Ⅲ Optical Characteristics (T OP = -5 to 85, VCC = 3.14 to 3.46 Volts) Parameter Symbol Min Typ Max Unit Ref. Transmitter Output Opt. Pwr POUT -6-1 dbm

Ⅲ Optical Characteristics (T OP = -5 to 85, VCC = 3.14 to 3.46 Volts) Parameter Symbol Min Typ Max Unit Ref. Transmitter Output Opt. Pwr POUT -6-1 dbm Ⅰ Absolute Maximum Ratings Parameter Symbol Min Typ Max Unit Ref. Maximum Supply Voltage Vcc -0.5 4.7 V Storage Temperature TS -40 85 C Case Operating Temperature Tcase -5 85 C Ⅱ Electrical Characteristics

More information

ES3112-3LCD Gbps SFP Optical Transceiver, 10KM Reach

ES3112-3LCD Gbps SFP Optical Transceiver, 10KM Reach ES3112-3LCD10 1.25Gbps SFP Optical Transceiver, 10KM Reach Features Data-rate of 1.25Gbps operation 1310nm FP laser and PIN photodetector for 10KM transmission Compliant with SFP MSA and SFF-8472 with

More information

GLC-LH-SMD-AO. 1.25Gbps SFP Transceiver

GLC-LH-SMD-AO. 1.25Gbps SFP Transceiver GLC-LH-SMD-AO Cisco 1000Base-LX SFP SMF 1310nm, 10km Reach, LC, DOM www.addonnetworks.com GLC-LH-SMD-AO 1.25Gbps SFP Transceiver Features Up to 1.25Gb/s data links Duplex LC connector Hot-pluggable SFP

More information

RoHS Compliant Small Form Factor Pluggable Transceiver for Gigabit Ethernet and Fiber Channel

RoHS Compliant Small Form Factor Pluggable Transceiver for Gigabit Ethernet and Fiber Channel LCP-1250D4UDRx RoHS Compliant Small Form Factor Pluggable Transceiver for Gigabit Ethernet and Fiber Channel FEATURES Compliant with SFP Transceiver SFF-8472 MSA specification with internal calibration

More information

Product Specification. 6.1 Gb/s Short-Wavelength SFP+ Transceiver FTLF8526P3BNL

Product Specification. 6.1 Gb/s Short-Wavelength SFP+ Transceiver FTLF8526P3BNL Product Specification 6.1 Gb/s Short-Wavelength SFP+ Transceiver FTLF8526P3BNL PRODUCT FEATURES Up to 6.1 Gb/s bi-directional data links Hot-pluggable SFP+ footprint Built-in digital diagnostic functions

More information

SFP+-DWDM-xx-80D. 10Gbps DWDM SFP+ Optical Transceiver, 80km Reach

SFP+-DWDM-xx-80D. 10Gbps DWDM SFP+ Optical Transceiver, 80km Reach SFP+-DWDM-xx-80D 10Gbps DWDM SFP+ Optical Transceiver, 80km Reach Features Available in all C-Band Wavelengths on the 100GHz DWDM ITU Grid Temperature-Stabilized DWDM EML Transmitter Duplex LC Connector

More information

Product Specification SFP WDM 1G 40km SC Transceiver

Product Specification SFP WDM 1G 40km SC Transceiver Product Specification 1. Product features Up to 1.25 Gb/s bi-directional data links Hot-pluggable SFP footprint 1310nm DFB Transmitter and 1550nm PIN Receiver for SFP-1SM-1310nm-40SC 1550nm DFB Transmitter

More information

1.25Gbps SFP Transceiver

1.25Gbps SFP Transceiver GLC-LH-SMD-EO 1.25Gbps SFP Transceiver Features Operating data rate up to 1.25Gbps 1310 nm FP LD Transmitter Distance up to 10km Single 3. 3V Power supply and TTL Logic Interface Duplex LC Connector Interface

More information

AddOn Computer s SFP transceivers are RoHS compliant and lead- free.

AddOn Computer s SFP transceivers are RoHS compliant and lead- free. SFP- 1000BASE- SX- AO 1000BASE- SX SFP MMF 850NM 550M REACH LC www.addoncomputer.com SFP- 1000BASE- SX- AO 1.25Gbps SFP Transceiver Features Up to 1.25Gb/s data links Duplex LC connector Hot- pluggable

More information

SFP+ BIDI Series JB1270-SFP-LC.S20

SFP+ BIDI Series JB1270-SFP-LC.S20 JB1270-SFP-LC.S20 Tx: 1270nm/Rx: 1330nm BIDI SFP+ Transceiver for 10GbE RoHS 6 Compliant Features Operating data rate up to 10.3Gbps 1270nm DFB Transmitter/ 1330nm Receiver Power budget up to 12dB Single

More information

ROHS Compliant MM SFP Transceiver 1.25Gb Gigabit Ethernet

ROHS Compliant MM SFP Transceiver 1.25Gb Gigabit Ethernet Product Overview WFT s SFP transceiver modules is specifically designed for the high performance and cost-effectiveness integrated duplex data link over a single fiber. The high-speed laser diode and photo

More information

Regulatory Compliance Electrostatic Discharge (ESD) to the Electrical Pins Electrostatic Discharge to the enclosure Electromagnetic Interference (EMI)

Regulatory Compliance Electrostatic Discharge (ESD) to the Electrical Pins Electrostatic Discharge to the enclosure Electromagnetic Interference (EMI) ST-SFP-4GE-S04 Series Single-Mode 1310nm for FC/2FC/4FC Duplex SFP Transceiver Features Operating Data Rate up to 4.25Gbps 1310nm FP Laser Transmitter 4Km with 9/125 μm SMF Single 3.3V Power Supply and

More information

SFP 155Mb/s Transceiver 2km Hot Pluggable, Duplex LC, +3.3V, 1310nm FP-LD MM PSFP M-12F

SFP 155Mb/s Transceiver 2km Hot Pluggable, Duplex LC, +3.3V, 1310nm FP-LD MM PSFP M-12F DATASHEET DESCRIPTION: Transceiver is a high performance, cost effective module which have a Duplex LC optics interface. Standard AC coupled CML for high speed signal and LVTTL control and monitor signals.

More information

SFP-10GD-LR-TP 10Gb/s 1310nm Single-mode SFP+ Transceiver

SFP-10GD-LR-TP 10Gb/s 1310nm Single-mode SFP+ Transceiver SFP-10GD-LR-TP 10Gb/s 1310nm Single-mode SFP+ Transceiver PRODUCT FEATURES 10Gb/s serial optical interface compliant to 802.3ae 10GBASE-LR. 1310nm DFB transmitter, PIN photo-detector Up to 10km transmission

More information

10G SFP+ CWDM 20km Transceiver Hot Pluggable, Duplex LC, +3.3V, 1270~1350nm CWDM DFB, DDMI PSFP-2C41SF-XX

10G SFP+ CWDM 20km Transceiver Hot Pluggable, Duplex LC, +3.3V, 1270~1350nm CWDM DFB, DDMI PSFP-2C41SF-XX DATASHEET DESCRIPTION: transceiver is a very compact 10Gb/s optical transceiver module for serial optical communication applications, supporting data-rate of 10.3125Gbps (10GBASE-LR) or 9.953Gbps (10GBASE-LW),

More information

SFP Series IOLS-1624-XX-XX. 2.5Gbps APD High Sensitivity Receiver. version 0.1 FEATURES PRODUCT DESCRIPTION

SFP Series IOLS-1624-XX-XX. 2.5Gbps APD High Sensitivity Receiver. version 0.1 FEATURES PRODUCT DESCRIPTION 2.5Gbps APD High Sensitivity Receiver FEATURES MULTI-RATE OPERATION FOR 2.488/2.125/1.25/1.063 Gb/s 18-wavelength CWDM DFB LD Transmitter from 1270nm-1610nm, with step 20nm Features APD HIGH SENSITIVITY

More information

F i n i s a r. Product Specification. CWDM Pluggable SFP Transceiver FWLF15197Dxx APPLICATIONS

F i n i s a r. Product Specification. CWDM Pluggable SFP Transceiver FWLF15197Dxx APPLICATIONS Product Specification CWDM Pluggable SFP Transceiver FWLF15197Dxx PRODUCT FEATURES Up to 1.25 Gb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic functions Uncooled DFB

More information

10G CWDM SFP+ 40km ER Transceiver Hot Pluggable, Duplex LC, +3.3V, 1470~1610nm CWDM EML, DDMI PSFP10-1C41SF-XX

10G CWDM SFP+ 40km ER Transceiver Hot Pluggable, Duplex LC, +3.3V, 1470~1610nm CWDM EML, DDMI PSFP10-1C41SF-XX DATASHEET DESCRIPTION: CWDM SFP+ ER transceiver is a very compact 10Gb/s optical transceiver module for serial optical communication applications, supporting data-rate of 10.3125Gbps (10GBASE-ER) or 9.953Gbps

More information

AA C 1000BASE-CWDM, Small Form-factor Pluggable (SFP), 1.25Gb/s data rate, 1590nm wavelength, 70Km reach

AA C 1000BASE-CWDM, Small Form-factor Pluggable (SFP), 1.25Gb/s data rate, 1590nm wavelength, 70Km reach AA1419039-C 1000BASE-CWDM, Small Form-factor Pluggable (SFP), 1.25Gb/s data rate, 1590nm wavelength, 70Km reach FEATURES Up to 1.25Gb/s bi-directional data links Hot-pluggable SFP footprint 8 CWDM Wavelength

More information

LEG. 10Gbs SFP+ Transceiver

LEG. 10Gbs SFP+ Transceiver Part# 39719 430-4909-LEG DELL COMPATIBLE 10GBASE-LRM SFP+ MMF 1310NM 220M REACH LC DOM 430-4909-LEG 10Gbs SFP+ Transceiver Features Duplex LC connector Support hot-pluggable Metal with lower EMI Excellent

More information

NBASE-T Copper Transceiver Small Form Factor Pluggable (SFP+), 3.3V 100M/1G/2.5G/5G/10Gbps Ethernet. Features

NBASE-T Copper Transceiver Small Form Factor Pluggable (SFP+), 3.3V 100M/1G/2.5G/5G/10Gbps Ethernet. Features Features 10Gbps Links up to 35 m using Cat 6a/7 Cable 100M/1G/2.5G/5Gbps Links up to 100 m using Cat5e Cable Low Power Consumption 2.2W Max, 35m @ 10Gbps, 75 C 1.88W Max, 100m @ 2.5G and 5Gbps, 75 C 1.88W

More information

PRODUCT SPECIFICATION

PRODUCT SPECIFICATION PRODUCT SPECIFICATION P/N AC-SF-3G1-20 Description 1.25Gbps 1310nm LC Duplex 20km SFP Transceiver Version A0 Issue Date 2015.06.07 Prepared By Checked By Approved By Jason Qi Wenshan Yang Nan Wang AC-SF-3G1-20

More information

SFP-ZX-SM Gbps SFP Optical Transceiver, 80km Reach

SFP-ZX-SM Gbps SFP Optical Transceiver, 80km Reach SFP-ZX-SM-0280 1.25Gbps SFP Optical Transceiver, 80km Reach Features Dual data-rate of 1.25Gbps/1.063Gbps operation 1550nm DFB laser and PIN photodetector for 80km transmission Compliant with SFP MSA and

More information

Product Specification. 3.7 Gb/s RoHS Compliant Short-Wavelength SFP Transceiver FTLF8524P3BNL

Product Specification. 3.7 Gb/s RoHS Compliant Short-Wavelength SFP Transceiver FTLF8524P3BNL Product Specification 3.7 Gb/s RoHS Compliant Short-Wavelength SFP Transceiver FTLF8524P3BNL PRODUCT FEATURES Up to 3.7 Gb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic

More information

SFP+ Series. 1550nm SFP+ single-mode Transceiver, With Diagnostic Monitoring Duplex SFP+ Transceiver RoHS 6 Compliant

SFP+ Series. 1550nm SFP+ single-mode Transceiver, With Diagnostic Monitoring Duplex SFP+ Transceiver RoHS 6 Compliant JD1550-SFP-LC.S80 SFP+ Series 1550nm SFP+ single-mode Transceiver, With Diagnostic Monitoring Duplex SFP+ Transceiver RoHS 6 Compliant Features 1550nm cooled EML High sensitivity APD Receiver Distance

More information

10Gbps 1550nm 80KM SFP+ Optical Transceiver

10Gbps 1550nm 80KM SFP+ Optical Transceiver 10Gbps 1550nm 80KM SFP+ Optical Transceiver Model: JFSP5592-3LCD80 Size (mm): 58.4*13.9*12.6 Features Hot pluggable 1550nm cooled EML, APD Receiver Up to 80km on 9/125um SMF SFP+ MSA package with duplex

More information

LCP-1250A4FDRx RoHS Compliant Multimode SFP Transceiver for GbE and Fiber Channel

LCP-1250A4FDRx RoHS Compliant Multimode SFP Transceiver for GbE and Fiber Channel LCP-1250A4FDRx RoHS Compliant Multimode SFP Transceiver for GbE and Fiber Channel FEATURES Compliant with SFP Transceiver SFF-8472 MSA specification with internal calibration Compliant with Specifications

More information

Features Gigabit Ethernet

Features Gigabit Ethernet Applicatios Gigabit Ethernet Ordering Information Features ü Up to 1.25Gb/s data links ü Single SC/LC connector ü Hot-pluggable SFP footprint ü 1550nm DFB laser transmitter ü RoHS compliant and Lead Free

More information

OP-MP4 13L1SD-4 0. Product Features. Applications. General. 1.25Gb/s RoHS Compliant Pluggable SFP Transceiver

OP-MP4 13L1SD-4 0. Product Features. Applications. General. 1.25Gb/s RoHS Compliant Pluggable SFP Transceiver 1.25Gb/s RoHS Compliant Pluggable SFP Transceiver OP-MP4 13L1SD-4 0 Product Features Up to 1.25Gb/s data links Duplex LC connector Hot-pluggable SFP footprint 1310nm FP laser transmitter RoHS compliant

More information

10Gbps 1330/1270nm SFP+ BIDI TRx 80km

10Gbps 1330/1270nm SFP+ BIDI TRx 80km FEATURES Supports up to 11.3Gb/s bit rates -40 to 85 C operating case temperature SFP+ package with single LC receptacle connector Hot-pluggable capability Single 3.3V power supply 1330nm DFB transmitter

More information

OC-48 LR-2/STM L-16.2 RoHS Compliant Pluggable SFP Transceiver

OC-48 LR-2/STM L-16.2 RoHS Compliant Pluggable SFP Transceiver OC-48 LR-2/STM L-16.2 RoHS Compliant Pluggable SFP Transceiver PRODUCT FEATURES Up to 2.67Gb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic functions Uncooled 1550nm

More information

LX21 100Mb/s to 1.25Gb/s BX-U

LX21 100Mb/s to 1.25Gb/s BX-U Product Features Compliant with IEEE Std 802.3-2005,1000BASE- Compliant with SFF-8074i andsff-8472, revision 9.5 Compliant with SFP MSA Specification Digital Diagnostic Monitoring available Uncooled 1310nm

More information

PROLABS GLC-LH-SM-C 1.25GBd SFP (Small Form Pluggable) Long Wavelength (1310nm) Transceiver

PROLABS GLC-LH-SM-C 1.25GBd SFP (Small Form Pluggable) Long Wavelength (1310nm) Transceiver PROLABS GLC-LH-SM-C 1.25GBd SFP (Small Form Pluggable) Long Wavelength (1310nm) Transceiver GLC-LH-SM-C Overview ProLabs s GLC-LH-SM-C SFP optical transceivers are based on Gigabit Ethernet IEEE 802.3

More information

10Gbps 1550nm 80KM SFP+ Optical Transceiver 10Gbps 850nm 300M SFP+ Optical Transceiver

10Gbps 1550nm 80KM SFP+ Optical Transceiver 10Gbps 850nm 300M SFP+ Optical Transceiver 10Gbps 1550nm 80KM SFP+ Optical Transceiver 10Gbps 850nm 300M SFP+ Optical Transceiver Model: JFSP8592-3LCD03 Size (mm): 58.4*13.9*12.6 Features Optical interface compliant to IEEE 802.3ae Electrical interface

More information

SFP-LX 1.25Gb/s Single-Mode SFP Transceiver 1000BASE-LX Gb/s Fiber Channel

SFP-LX 1.25Gb/s Single-Mode SFP Transceiver 1000BASE-LX Gb/s Fiber Channel Product Features Compliant to IEEE Std 802.3-2005 Gigabit Ethernet 1000Base-LX Specifications according to SFF-8074i and SFF-8472, revision 9.5 Digital Diagnostic Monitoring available Uncooled 1310nm Fabry-Perot

More information

SFP 1G 150km CWDM (1470~1610) Transceiver datasheet A-GEAR World Wide Manufacturing Product Specification 1. Featur es 2.

SFP 1G 150km CWDM (1470~1610) Transceiver datasheet A-GEAR World Wide Manufacturing Product Specification 1. Featur es 2. Product Specification 1. Features Up to 1.25Gb/s data links DFB laser transmitter and APD receiver Up to 160km on 9/125μm SMF Hot-pluggable SFP footprint Duplex LC/UPC type pluggable optical interface

More information

The Price Performance Leader in 100% Compatible Optical Transceivers

The Price Performance Leader in 100% Compatible Optical Transceivers Part Number: CWDM-GBIC-1570 Quick Spec: Manufacturer Compatibility: Form Factor: TX Wavelength: Reach: Cable Type: Rate Category: Interface Type: Digital Optical Mon. (DOM): Connector Type: Cisco GBIC

More information

The Price Performance Leader in 100% Compatible Optical Transceivers

The Price Performance Leader in 100% Compatible Optical Transceivers Part Number: CWDM-GBIC-1470 Quick Spec: Manufacturer Compatibility: Form Factor: TX Wavelength: Reach: Cable Type: Rate Category: Interface Type: Digital Optical Mon. (DOM): Connector Type: Cisco GBIC

More information

LEG. 10Gbps SFP+ Transceiver

LEG. 10Gbps SFP+ Transceiver 430-4585-LEG DELL 10GBASE-ER SFP+ SMF 1550NM 40KM REACH LC DOM 430-4585-LEG 10Gbps SFP+ Transceiver Features Duplex LC connector Support hot-pluggable Metal with lower EMI Excellent ESD protection RoHS

More information

CTS-LC0010-SM 1.25Gb/s 1310nm Single-mode SFP Transceiver

CTS-LC0010-SM 1.25Gb/s 1310nm Single-mode SFP Transceiver CTS-LC0010-SM 1.25Gb/s 1310nm Single-mode SFP Transceiver PRODUCT FEATURES Up to 1.25Gb/s data links FP laser transmitter and PIN photo-detector Up to 10km on 9/125µm SMF Hot-pluggable SFP footprint Duplex

More information

Part Number Operating temperature DDMI. APS31123CXL2 Commercial No. APS31123CDL2 Commercial Yes. APS31123IXL2 Industrial No

Part Number Operating temperature DDMI. APS31123CXL2 Commercial No. APS31123CDL2 Commercial Yes. APS31123IXL2 Industrial No APS31123xxL2 Product Features Up to 1.25Gb/s data links Duplex LC connector Hot-pluggable SFP footprint 1310nm FP laser transmitter RoHS compliant and Lead Free Up to 2Km on 9/125um SMF Metal enclosure

More information

AXGE Gbps Single-mode 1310nm, SFP Transceiver

AXGE Gbps Single-mode 1310nm, SFP Transceiver AXGE-1354 1.25Gbps Single-mode 1310nm, SFP Transceiver Product Overview Features The AXGE-1354 family of Small Form Factor Pluggable (SFP) transceiver module is specifically designed for the high performance

More information

SNR-SFP-LX 1.25Gbps. Features. Applications. Product Description

SNR-SFP-LX 1.25Gbps. Features. Applications. Product Description Features Operating data rate up to 1.25Gbps 1310 nm FP LD Transmitter Distance up to 30km Single 3. 3V Power supply and TTL Logic Interface Duplex LC Connector Interface Hot Pluggable Operating Case Temperature

More information

PRE-SFP-OC Mb/s Transceiver, 1310 nm, 15 km (IR1), DDM

PRE-SFP-OC Mb/s Transceiver, 1310 nm, 15 km (IR1), DDM Product Features Up to 155 Mb/s Data Links Hot-Pluggable 1310nm FP laser transmitter Duplex LC connector RoHS compliant and Lead Free Up to 20 km on 9/125 µm SMF Single +3.3V Power Supply Low power dissipation,

More information

F i n i s a r. Product Specification. CWDM Pluggable SFP Transceiver FWLF15197Dxx APPLICATIONS. FWLF15197Dxx

F i n i s a r. Product Specification. CWDM Pluggable SFP Transceiver FWLF15197Dxx APPLICATIONS. FWLF15197Dxx Product Specification CWDM Pluggable SFP Transceiver FWLF15197Dxx PRODUCT FEATURES Up to 1.25 Gb/s bi-directional data links Operating temp. range: 0 to 70 C Low power dissipation

More information

AFBR-59F2Z Data Sheet Description Features Applications Transmitter Receiver Package

AFBR-59F2Z Data Sheet Description Features Applications Transmitter Receiver Package AFBR-59F2Z 2MBd Compact 6nm Transceiver for Data communication over Polymer Optical Fiber (POF) cables with a bare fiber locking system Data Sheet Description The Avago Technologies AFBR-59F2Z transceiver

More information

Product Features Applications Descriptions Ordering Information

Product Features Applications Descriptions Ordering Information Product Features Compliant with IEEE Std 802.3-2005, Gigabit Ethernet 1000Base-EZX Compliant with SFF-8074i andsff-8472, revision 9.5 Compliant with Fiber Channel FC- PI-2 Rev.8.0 Compliant with SFP MSA

More information

F i n i s a r. Product Specification. Long-Reach DWDM SFP Transceiver FWLF1631Rxx PRODUCT FEATURES

F i n i s a r. Product Specification. Long-Reach DWDM SFP Transceiver FWLF1631Rxx PRODUCT FEATURES Product Specification Long-Reach DWDM SFP Transceiver FWLF1631Rxx PRODUCT FEATURES Up to 2.7 Gb/s bi-directional data links High launch power (+3dBm MIN) Hot-pluggable SFP footprint Temperature-stabilized

More information

1.25Gb/s SFP Transceiver P/N: MO-C-S31123CDL20. Product Features. Applications. General. Regulatory Compliance. Up to 1.

1.25Gb/s SFP Transceiver P/N: MO-C-S31123CDL20. Product Features. Applications. General. Regulatory Compliance. Up to 1. 1.25Gb/s SFP Transceiver P/N: MO-C-S31123CDL20 Product Features Up to 1.25Gb/s data links Duplex LC connector Hot-pluggable SFP footprint 1310nm FP laser transmitter RoHS compliant and Lead Free Up to

More information

XFP BIDI Series JB1330-XFP-LC.S60. Features. Applications. Ordering information. Regulatory Compliance

XFP BIDI Series JB1330-XFP-LC.S60. Features. Applications. Ordering information. Regulatory Compliance JB1330-XFP-LC.S60 XFP BIDI Series Tx: 1330nm/Rx: 1270nm BIDI XFP Transceiver for 10GbE/10FC RoHS 6 Compliant Features Supports 9.95Gb/s to 10.5Gb/s data rates Power budget 21dB at least 1330nm DFB Transmitter/

More information