POWER FACTOR (Typ.) PF 0.975/230VAC, PF 0.96/277VAC at rated power (Please refer to "Power Factor Characteristic" curve)

Transcription

1 SPECIFICATI MODEL SELECTABLE CURRENT Note. ma DC VOLTAGE RANGE RATED POWER ~ 57V W RIPPLE CURRENT ±5.0% OUTPUT RIPPLE & NOISE (max.) Note. mvp-p NO OUTPUT VOLTAGE (max.) 65V CURRENT ACCURACY ±5.0% SETUP, RISE TIME Note.5 000ms, ms / 0VAC at rated power HOLD UP TIME (Typ.) 6ms/0VAC at rated power VOLTAGE RANGE Note. ~ 95VAC 5 ~ 7VDC FREQUENCY RANGE 7 ~ 6Hz POWER FACTOR (Typ.) PF 0.975/0VAC, PF 0.96/77VAC at rated power (Please refer to "Power Factor Characteristic" curve) INPUT TOTAL HARMIC DISTORTI Total harmonic distortion will be lower than 0%when output loading is 75% or higher EFFICIENCY (Typ.) Note.6 9% AC CURRENT (Typ.) 0.A/0VAC 0.A/77VAC INRUSH CURRENT(Typ.) LEAKAGE CURRENT COLD START 0A(t width=60μ s measured at 50% I peak) at 0VAC <0.5mA / VAC SHORT CIRCUIT Constant current limiting, recovers automatically after fault condition is removed 0 ~ 0V OVER VOLTAGE PROTECTI Protection type : Shutdown o/p voltage, re-power on to recover OVER TEMPERATURE 90 ± 0 (RTH) Protection type : Shut down o/p voltage, re-power on to recover AUXILIARY POWER 50mA for driving fan; Tolerance± 5% FUNCTI TEMP. COMPENSATI By external NTC(not provide with the power supply), please see "Temperature Compensation Operation" DIMMING Please see "Dimming Operation" SYNCHRIZATI Please see "Synchronization Operation" WORKING TEMP. WORKING HUMIDITY ENVIRMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATI SAFETY & EMC OTHERS NOTE SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATI RESISTANCE EMC EMISSI EMC IMMUNITY -0 ~ +60 (Refer to "Derating Curve") 0 ~ 90% RH non-condensing - ~ +, 0 ~ 95% RH ± 0.0%/ (0 ~ 50 ) 0 ~ Hz, G 0min./cycle, period for 60min. each along X, Y, Z axes UL8750, ENEC EN67-, EN67--, EN68 independent approved I/P-O/P:.75KVAC Ⅱ I/P-O/P:>00M Ohms / VDC / 5 / 70% RH Compliance to EN5505, EN0-- Class C( % rated power) ; EN0-- Compliance to EN0--,,,5,6,8,, EN550, EN657 light industry level (surge KV), criteria A MTBF 60.6K hrs min. MIL-HDBK-7F (5 ) DIMENSI.5*8.5*mm (L*W*H) PACKING 0.Kg ; 5pcs/5Kg/.CUFT ~

2 Mechanical Specification Case No. AUnit:mm T case: Max. Case Temperature TB T case TB SYN. 5 6 CN0 CN00 TB M TerminalPin No.Assignment(TB) Pin No. Assignment AC/L AC/N Terminal Pin No.Assignment(TB) Pin No. Assignment Pin No. +FAN -FAN 5 +NTC 6 Terminal Pin No.Assignment(TB5) Pin No. Assignment +Vo -Vo SYN. Connector(CN0/CN00):JST BB-XH or equivalent Pin No. Assignment Mating Housing, + JST XHP, - or equivalent B ottom View Assignment -NTC DIM+ DIM- Terminal JST SXH-00T-P0.6 or equivalent Block Diagram PFC fosc : 60KHz PWM fosc : KHz +Vaux I/P EMI FILTER & PFC CIRCUIT POWER SWITCHING & FILTER CURRENT LIMIT +V -V DIM+ DIM- PFC CTROL O.L.P. O.T.P. PWM CTROL O.V.P. DETECTI CIRCUIT Derating Curve Static Characteristics Others mA AMBIENT TEMPERATURE ( ) (HORIZTAL) INPUT VOLTAGE (V) 60Hz

3 DIP Switch Table DRLCM is a multiple-stage output current supply, selection of output current through DIP switch as table below. I o DIP S.W mA ma ma ma(factory Setting) ma 050mA Power Factor Characteristic Constant Current Mode Constant Current Mode % 0% 0% % 50% 60% 70% % 90% 00% (W) (0Vac Input) % 0% 0% % 50% 60% 70% % 90% 00% (W) (77Vac Input) EFFICIENCY vs DRLCM series poss ess superior working efficiency that up to 9% can be reached i n field applic ati ons. 95.0% 95.0% 90.0% 90.0% 85.0% 85.0%.0% 75.0% 70.0% 65.0% 50.0% 75.0% 70.0% 65.0% % 60.0% 55.0% % % 50.0% 5.0% 0% 0% 0% % 50% 60% 70% % 90% 00% 5.0% 0% 0% 0% % 50% 60% 70% % 90% 00% (0Vac Input) (77Vac Input)

4 DIMMING OPERATI Built-in in dimming func tion, outputconstant current levelcan be adjusted through outputterminalby 0 ~ 0Vdcor 0VPWMsignal between DIM+ and DIM-. Please DO NOT connect "DIM-" to "-Vo". 0V PWM signal for ou tput current adjustmen t (Typical): Frequency range :00Hz ~ KHz 0 ~ 0V dimmingfunctionforoutputcurrentadjustment (Typical) Dimming value 0V V V V V 5V 6V 7V 8V 9V 0V OPEN Output current 0% 0% 0% 0% % 50% 60% 70% % 90% 00% 00%~08% Duty value 0% 0% 0% 0% % 50% 60% 70% % 90% 00% OPEN Output current 0% 0% 0% 0% % 50% 60% 70% % 90% 00% 00%~08% SYNCHRIZATI OPERATI 0 drivers(max.) synchronization ( master + 9 slaves) Maximum cable length between each units : 0 meter. DRLCM ( Slave ) SYN. DRLCM SYN. DRLCM SYN. (Master) (Slave ) 0m 0m

5 TEMPERATURE COMPENSATI OPERATI 05 NTC derating curve KΩ 0KO 0KΩ 0KO 70KΩ 70KO Sensed Temperature(degree) DRLCM have the built-in temperature co mpensation function (T,Io ). By connecting a temperature sensor (NTC resistor) between the NTC +/- ter minal of DRLCM and the detecting point on the light ing system or the surrounding environment, output c urrent of DRLCM coul d be co rrespondingly changed to ensure the long life of LED..DRLCM can still be operated well when the NTC resistor is not connected and the va lue of output cu rrent wi ll be the current level that you set through the DIP switch.. NTC resistance 0K 0K 70K Output Current < 60, 00% of the rated current (corresponds to the setting current level) > 60, output current begin to reduce, details please refer to the curve. < 70, 00% of the rated current (corresponds to the setting current level) > 70, output current begin to reduce, details please refer to the curve. <, 00% of the rated current (corresponds to the setting current level) >, output current begin to reduce, details please refer to the curve. Notes:. MW does not offer the NTC resistor and all the data above are measured by using THINKING TTC0 series.. If other brands of NTC resistor is applied,please check the temperature curve first.