Simpson Digital Meters/Controllers

Transcription

1 Simpson igital Meters/ontrollers Includes new temperature measurement models (H340) ll Parameters Set from Front Panel 7 Segment 4-1 /2 or 3-1 /2 igit right Red isplay Screw Terminals for asy Installation 1/8 IN Shallow epth ase Peak/Valley and Password Lockout Optional Plug-In Output and xcitation ards Optional Plug-In ards for One, Two or Four 5 mp Relays NM 4X Rated Front Panel isplay Type: 7 segment, red L Quantity: H335: 3 1 /2 digit; H345: 4 1 /2 digit; H340: 4 digit Height: 0.56" (14.2 mm) ecimal Point: H335 and H340: 4-position, user programmable H345: 5- position, user programmable rightness: 5 Levels, user programmable larm Indicators: 4 L indicators for up to four set points Power Requirements Voltages: 120, V Voltages: V 25 : : H335: 0.1% of input ±1 digit H345: 0.05% of input ±1 digit : H335: 0.2% ±2 digits H345: 0.1% ±2 digits Sensor Type ccuracy Temperature Range RT Pt % of input ±2 count -200 to +200 J 0.2% of input ±2 counts -100 to +760 K 0.2% of input ±2 counts -200 to % of input ±2 counts -100 to +800 T 0.2% of input ±2 counts -200 to +400 Mechanical ezel: 3.93 x 2.04 x.52" (98.8 x 51.8 x 13.2 mm) epth: 3.24" (82.33mm) behind panel Panel ut-out: 1 /8 IN 3.62 x 1.77" (92 x 45 mm) ase Material: PT-S Weight: 10 oz (283.5g) Temperature: 0-50 Sample Rate: 10/sec F asic Temperature Meter nalog Output H340 4 digit Red L m V Power Supply 5 mp Relays 1 120V V 1 One V 2 Two 4 Four Function Range F xcitation Output 91 J Thermocouple 92 K Thermocouple 1 12V (30m max) 93 RT, Pt100, 3-wire 2 24V (30m max) 94 Thermocouple 95 T Thermocouple Order xample: H F F H345 asic Panel Meter H /2 digit Red L H /2 digit Red L Power Supply 1 120V (3 1 /2 digit only) V (4 1 /2 digit only) V V (3 1 /2 digit only) Function/Range mV mV TRMS 12 2V 52 2V TRMS V 53 20V TRMS V V TRMS V TRMS µ µ TRMS 22 2m 62 2m TRMS 23 20m 63 20m TRMS m m TRMS TRMS TRMS mV m Process 32 2V V Process 33 20V V Ohm V 82 2k Ohm 83 20k Ohm µ k Ohm 42 2m 43 20m m Output Signal m Process V Process 6 RS-485 (4 1 /2 digit only) 5 mp Relay Outputs 1 One 2 Two 4 Four xcitation Output (not available with Signal Output) 1 12V (30m max) 2 24 (30m max) IGITL MTRS 20

2 Simpson igital Panel Meters F35 M235 IGITL M TRS ase Size: Standard 1/8 IN ccuracy: ±0.2% (F35); ±0.05% (F45); ±0.5% (F45) uto-zero hoice of or Power Supplies road Range Scaling and djustable Zero Offset for Process Inputs User-Selectable ecimal Points Optional xcitation Output 12 V or 24 V asy Installation Using Screw Terminals ase Size: Standard 3/64 IN imensions ccuracy: ±0.5% (M235); ±0.5% (M245) Minimum epth Indicator Less Than 2.5" (60 mm) of Space User-Selectable ecimal Point Optional Negative Image, right Red acklighting Standard Screw Terminals 85V to 250 V Power or 9V to 32 V To Order Insert Number ode for ach Letter to Select atalog Number Order xample: F asic Unit F /2-igit Meter F /2-igit Meter Power Supply V V V Input Range Input Range Voltage Voltage RMS 200 mv V V V urrent urrent RMS (F35 Only) 200 µ m m m Process m V V Temperature (F45 only) 80 J T/ 84 T/ 81 K T/ 85 R T/ 82 S T/ 86 mv 83 T T/ 90 RT PT 100 Frequency RMS (F35) Sq. Wave (F35) Hz Hz xcitation Output ( Input Only) 1 12 V 2 24 V Mini-Max 3/64 IN, and igit and Process Indicators Simpson s Mini-Max Voltage/urrent Indicators provide high quality, accuracy, and reliability in a compact 60 mm deep case. Power: Size: Order xample: M V Hz 440 Hz; or 9V 32 V 2.84W x 0.95 x 2.36" WH (72 x 24 x 60 mm) asic Unit M /2-igit L Meter M /2-igit L Meter isplay 0 Non-acklit 1 Negative Red acklight Supply Voltage V V* Function Range mv mv TRMS 12 2 V 32 2 V TRMS V V TRMS V V TRMS µ V TRMS 22 2 m µ TRMS m 42 2 m TRMS m m TRMS m TRMS TRMS m 46 5 TRMS V Hz V Hz V Hz Sq. Wave Hz Sq. Wave xcitation Output (N with Frequency) 1 12 V 2 24 V * Not vailable on Frequency (Hz) Meters 21

3 Laurel High Performance PMs FTURS ±99999 isplay Span User Selectable Ranges 60 Readings Per Second daptive igital Filter 1/8 IN, NM-4X Front 5, 10, 24V xcitation Out Laureate PMs offer exceptional accuracy at high reading rates. dvanced programming features provide flexibility in measuring V, V,,, temperature, weight, strain, process & pot follower. isplay Five 14.2 mm (.56 ) high L digits -to- onversion -to- rate 60/s at 60 Hz, 50/s at 50 Hz isplay update 3.5/s at 60 Hz, 3/s at 50 Hz ccuracy at 25, Process < 0.01% FS ±1 ct Strain, Load < 0.01% FS ±1 ct True RMS < 0.1% FS (10 Hz-10 khz) F = 3.0 at full scale ( or coupled) Thermocouple < 0.2 RT < 0.1 Noise Rejection MR, to 60 Hz 130 d NMR to 50/60Hz line 90 d with min filtering Transducer xcitation Output (std) Output 100 5V, V, 50 24V ual Relay Output (opt) ontact relays. 250 Vac or 24 Vdc Solid state relays 140 Vac or 180 Vdc Linerarized nalog Output (opt) Level 0-20 m, 4-20 m, 0-10 Vdc, ±10 V Resolution 16 bits (0.0015%) nvironmental Operating temperature 0 55, 95% RH at 40, non-condensing ata ommunications (opt) Type US, RS-232, RS-485 (2- or 4-wire) Protocol Modbus RTU, Modbus SII or Laurel SII L01 L02 L05 SSORIS RJ11 TO 9 able to P om port US to 9 dapter US able to P US Port OPTIONS (all outputs isolated) ual Setpoint Relay Outputs Linearized Isolated nalog Transmitter Outputs US, RS-232 & RS-485 ata I/O ustom urve Linearization atalogging P Software xample: L10010V1 Laureate Series L Laureate Panel Meter LW Laureate Weight Meter Main oard 1 PM with green Ls 2 PM with red Ls 3 xtended, green Ls 4 xtended, red Ls Note: xtended capability for PMs is required for custom curve linearization. Power Vac/ Vdc Vdc/12-30 Vac Setpoint Output 1 ual 8 relays 2 ual solid state relays nalog Output m & 0-10 V igital Interface 1 RS-232 (Isolated) 2 RS-485 (Isolated) 4 RS485 Modbus (Isolated) 5 US 6 US to RS-485 onverter Input Type Volts V mv V V V V V V V V mperes m m m Process Signals (4-20 m, 0-5 V, etc.) P 4-20 m = P1 ustom Scaling Strain Gage, Potentiometer (4-wire ratio) SG mv = SG1 ustom Scaling Note: The same signal conditioner board can be user configured for Volts, mps, process, or strain. 100-Ohm Platinum RTs P to 850 P385F -331 to 1562 F P to 850 P392F -331 to 1562 F Thermocouples J -210 to 760 F -400 to 1830 F JF -347 to 1400 F N -245 to 1300 K -244 to 1372 NF -410 to 2370 F KF -408 to 2501 F S -46 to 1768 T -257 to 400 SF -51 to 3214 F TF -430 to 752 F R -45 to to 1000 RF -49 to 3213 F Note: The same temperature signal conditioner board can be user configured for all T/ and RT types TRMS Volts RMV mv RMV V RMV V RMV V RMV V (Not gency pproved) RMV V TRMS mperes RM m RM m RM m RM Note: The same RMS signal conditioner can be user-configured for Volts or mps Load ells (6-wire ratio) WM1-99,999 to +99,999 Note: xcitation is 10V for up to four 350Ω load cells in parallel IGITL MTRS 22

4 Selco igital Panel Meters Universal Type IGITL M TRS Seven Output hoices Front Panel Membrane Set uttons ighteen Input hoices vailable Two Setpoint isplays V or 9-60V Power Supply RS-232/RS-485 ommunications Industry Standard 1/8 IN Size 8-mp Setpoint ontact Relays 5000 Series Main display: 4 igit Red L 14.2mm Sub display: ual, Green L 8mm (Hi & Lo setpoints) onversion rate: 12.5 times/sec Maximum display: 9999 Overrange indication: When input exceeds the maximum display, display OL or -OL Zero display: Leading zero suppression ecimal point: Settable to any digit position xternal control: Start/Hold, Peak Hold, igital Zero Operating temperature: 0 to 50, 35 to 85% RH Storage temperature: -10 to 70 less than 60% RH Power supply: 100 to 240V ±10% ( main unit) 9 to 60V ( main unit) Power consumption: pprox. 4V (at 100V) imensions: 96mm x 48mm (H) x 147.5mm () IN size ielectric strength (): Power supply/input terminal/output terminal 2000V/1 min. Input terminal/output terminal 500V/1 min. ase/power supply/input terminal/output terminal 2000V/1 min. ielectric strength (): Power supply/input terminal/output terminal 500V/1 min. Input terminal/output terminal 500V/1 min. ase/power supply/input terminal/output terminal 2000V/1 min. Insulation resistance: 500V more than 100MΩ at the above terminals Input: Voltage: 40Hz to 1kHz urrent: 40Hz to 1kHz 0.1Hz to 200kHz 30V p-p Max. Strain Gauge: djustment Span: 1 to 3 mv/v xcitation: 5V@15m, 10V@30m nalog Output: 0-1V, 0-10V, 1-5V, 4-20m Setpoint Relays: 8@240V, 30V Resistive xample S/51/25-03 S/5 - Main oard V (±10%) V isplay oard 1 Single (Main isplay Only) 2 Multiple (Main & Sub isplays) Output 1 HI & LO setpoint 2 nalog output 3 RS RS HI & LO setpoint + analog output 6 HI & LO setpoint + analog output + RS HI & LO setpoint + analog output + RS-485 Input Ranges 01 voltage (±99.99mV) 1 02 voltage (±999.9mV to ±600V) 4 03 current (±9.999m to ±999.9m) 3 04 voltage VG (99.99mV to 9.999V) 3 05 voltage VG (99.99V to 600V) 2 06 voltage RMS (99.99mV to 9.999V) 3 07 voltage RMS (99.99V to 600V) 2 08 current VG (9.999m to 999.9m) 3 09 current VG (5) 1 10 current RMS (9.999m to 999.9m) 3 11 current RMS (5) 1 12 Resistance (99.99Ω to 99.99KΩ) 4 13 Temperature (Thermocouple) JKTSR 14 Temperature (RT) Pt Frequency (Open collector, Logic, Magnet) 4 16 Frequency (50 to 500Vrms) 17 Strain gauge 18 1 to 5V, 4 to 20m 23

5 London lectronics Programmable Meter 1/8 IN, IP65 Front Large 0.55" L isplay Simplified Setup No Menus isplay Filtering 10-Point ustom Linearization 0.05% asic ccuracy Variable rightness isplay Intuitive 2 Input types to match common sensors & process signals. rompton igital Metering System Measured Parameters 0.2% asic ccuracy Field Selectable T & PT Ratios thernet or RS-485 Interface 1/4 IN ase The Integra 1630 has Modbus communication and field selectable system configuration: single-phase, three-phase threewire or three-phase four-wire. Measure & isplay System (average) volts System (average) current System (total) kw System volts (average) TH% System current (average) TH% Volts L1 N, L2 N, L3 N Volts L1 L2, L2 L3, L3 L1 Volts L1 N TH% Volts L2 N TH% Order xample: INT2-P R- INT2- F F Input Type P Process: 0-10V, 1-5V, 0-10m, 4-20m M Millivolt Input for use with shunts T Temperature: J K T R S N & Pt100, F & R 4-Wire Resistance: specify range to 20kΩ L Load ell: 4/6-wire, w/ 10V excitation I Flow Integrator: 0-10V, 4-20m H lock/timer, numeric or HH:MM:SS display ounter/frequency/rpm/quadrature S Remote isplay, serial SII data input nalog Output (Isolated) NV 0 10V NI 4 20 m N -10 to +10V Relay Output (2@250 V) L4 4 Form L2 2 Form SPO 2 Form Serial ata Output 232 RS-232 M RS-485 Modus RTU 485 RS-485, SII N thernet isplay olor R Red Y Yellow G Green Supply Voltage V V Volts L3 N TH% Volts L1 L2 TH% Volts L2 L3 TH% Volts L3 L1 TH% urrent L1, L2, L3 urrent line 1 TH% urrent line 2 TH% urrent line 3 TH% Neutral current NW Frequency Power factor (overall) kvr, kv, kw kw Hr import, export (7 digits) kvrh import, export (7 digits) kw demand urrent demand Maximum kw demand Maximum current demand Hours run Measuring Ranges INT-1630 xample INT-1630-M-5-M-110 Voltage: % of nominal (functional 5-120%) urrent: 5-120% of nominal 45-66Hz Input Voltage Power Factor: 0.8 capacitive to 0.8 inductive L L-N ( L-L) TH: Up to 31st harmonic 0% - 40% M L-N ( L-L) nergy: 7 digit resolution Input urrent (T secondary) Input 5 5 PT Ratio (primary): up to 400kV ** 1 1 T Ratio: 9999:5 ** uxiliary Voltage Outputs L V RS-485: Half duplex (2-wire) M V / aud rates: 4800, 9600, 19200, Options Pulsed: 1 or 2 Solid state relays 00 Pulse duration: 60, 100 or 200 milliseconds 010 RS-485 Modbus RTU ontact rating: 50m max at 250V max. 100 One Pulse uxiliary Supply 200 Two Pulse / supply: V, V, 45 66Hz 210 Two Pulse & Modbus supply: V 110 One Pulse & Modbus urden: 6V 070 thernet Modbus TP ** 360MW max at 120% of relevant input 24 IGITL MTRS

6 rompton igital Metering Systems IGITL MTRS Integra Line 4 igit L isplay Self or xternally Powered Programmable T Ratios (1-8000) Setup Password Protection IP54 Front Integra urrent L1 urrent L2 urrent L3 2 Volts L1 N (4 wire only) Volts L2 N (4 wire only) Volts L3 N (4 wire only) isplay up to 12 electrical parameters on 4 screens: 3 Volts L1 L2 Volts L2 L3 Volts L3 L1 4 System Volts System urrent System Frequency Integra 640 isplay Voltage, urrent & Frequency True RMS Measurement Fully Programmable PT and T Ratios Simple Menu riven Interface NSI ase right L isplay isplay up to 12 electrical parameters on 4 screens: 1 System Volts System urrent System Frequency 2 Volts L1 N (4 wire only) Volts L2 N (4 wire only) Volts L3 N (4 wire only) Integra Volts L1 L2 Volts L2 L3 Volts L3 L1 4 urrent L1 urrent L2 urrent L3 Max Input Voltage: 120% of nominal continuous, 2x for 1 sec. Input Voltage urden: 0.2 V per line, nominal Max Input urrent: 120% of nominal continuous, 20x for 1 sec. Input urrent urden: 0.6 V per phase, nominal uxiliary Supply Tolerance: -10%, +20% of nominal range Frequency Range: 45-66Hz Supply urden: 3V Measuring Range Voltage (Self Powered): % of nominal Voltage (ux. Powered): % of nominal Line-Line Voltage, 4 Wire: 0-10% difference in phase voltage urrent: % of nominal Frequency Range: 45-66Hz ccuracy Voltage: 1.5% of nominal urrent: 1.5% of nominal 0.5% of mid frequency Operating Temperature: -10 to +70, <95% RH non-condensing Storage Temperature: -20 to +80 nclosure: Polycarbonate UL94V-0/V-2 Terminals: M3.5 captive screw clamp ompliance: UL3111-1, I T III, I688:1992 imensions: 96mm x 96mm x 112mm deep Panel ut Out: 92mm x 92mm (3.62" x 3.62") Order xample: R/ W-10LS-10 asic Unit R/ W 3 phase 3 wire R/ W 3 phase 4 wire Measured Input Range 10L V L-L (58-69V L-N), 1 T 19L V L-L ( V L-N), 1 T 38L V L-L ( V L-N), 1 T 10LS V L-L (58-69V L-N), 5 T 19LS V L-L ( V L-N), 5 T 38LS V L-L ( V L-N), 5 T uxiliary Supply SP Self powered V V V 25 Max Input Voltage: Input Voltage urden: Max Input urrent: Input urrent urden: System PT (primary): System T: uxiliary Supply Supply: 120% of nominal continuous, 2x for 1 sec. 0.2 V per line, nominal 120% of nominal continuous, 20x for 1 sec. 0.6 V per phase, nominal 400kV or 360MW max 9999:5 or 360MW max V or nominal (85 287V bsolute) (85 312V bsolute) Hz 12-48V ( V bsolute) 6V Frequency Range: Supply: Supply urden: Measuring Ranges Voltage: % of nominal (functional 4-120%) urrent: 5-120% of nominal 45-66Hz ccuracy Voltage: ±0.1% of range ±0.4% of reading urrent: ±0.1% of range ±0.4% of reading 0.15% of mid frequency Operating Temperature: -20 to +70, <95% RH non-condensing Storage Temperature: -30 to +80 nclosure: Polycarbonate front and base, steel case Terminals: arrier terminal strip, 6-32 screw ompliance: UL140758, I 1010, IP54 (front face) imensions: 4.31" high x 4.31" wide x 6.7" deep Panel ut Out: 4.06" (103mm) diameter, 4 stud positions Order xample: R/INT-0643-MIV-5-L asic Unit R/INT 0644 Integra 0640, 3 phase 4 wire R/INT 0643 Integra 0640, 3 phase 3 wire Input Voltage LV V L-L ( V L-N) LOV V L-L ( V L-N) MIV V L-L ( V L-N) HIV V L-L ( V L-N) Input urrent 5 5 T input uxiliary Supply V V

7 lectro Industries Power Meter Shark Multifunction TRMS Measurements Meets NSI and I % ccuracy lass right 0.56" 3 Line L isplay % of Load ar for nalog Perception Programmable T & PT Ratios Modbus and NP Protocol RS-485, thernet or fiber communication Parameter ccuracy isplay Voltage L-L & L-N: 0.1% V or kv, scalable urrent: 0.1% mps or kmps ± Watts 0.2% Watts, kwatts, MWatts ±Wh 0.2% 5 to 8 igits Programmable ±VRs 0.2% VRs, kvrs, MVRs ±VRh 0.2% 5 to 8 igits Programmable V 0.2% V, kv, MV Vh 0.2% 5 to 8 igits Programmable PF 0.2% ±0.5 to 1.0 Frequency 0.01 Hz 45 to 65 Hz %TH 1.0% 0 to 100% % Load ar 1-120% 10 igit Resolution Scalable Real time measurements for all parameters; plus Min/Max for V,, W, Vr, V, PF, f, %TH: verage for, W, Vr, V, PF System: Voltage Input: Max. urden: urrent Withstand: Max. urden: Pass-thru Wire: Isolation: Operating Temp: Sampling: 3 lement Y, 2.5 lement Y, 2 lement, 4 Wire 0-416V L-N, 0-721V L-L 0.36V per phase at 600V, 0.014V at 120V 100 for 10sec, 300 for 3sec, 500 for 1sec 0.005V per phase at " (4.5mm) max dia. ll Inputs and Outputs are galvanically isolated to 2500V -30 to +70, <95% RH non-condensing 400+ Samples/ycle, all channels measured simultaneously 1sec, except 100msec on Watts, Vr, V V / V, 10V RS485 Port (rear), Ir (faceplate) Update Rate: Power Supply: ommunications: Protocol: Modbus RTU, SII or NP 3.0 imensions, Ratings: 4.85"H x 4.82"W x 4.25", NM12 F Order xample: I/Shark V2-485-X I/SHRK F Model* 100 Power Meter/Transducer with L isplay 200 dvanced Power Meter/Transducer Frequency 50 50Hz 60 60Hz urrent Input lass (5 nominal) (1 nominal) Functions V1 Volts/mps V2 V1 + Power & Frequency V3 V2 + nergy ounters, NP3.0 V4 V3 + Harmonics & Limits ommunications X None 485 RS-485 F Mounting X NSI IN IN mounting brackets * dd suffix T for Transducer only (IN mount) without display Simpson igital Power Meters Measure up to 23 Parameters Standard 1/4 IN ase Wide acklit L isplay Four Keys Select ll Parameters Software etection/orrection of Wiring rrors Parameter G100 G200 G300 G400 Phase mps Phase Volts Line Volts Per phase PF Per phase kw Per phase kvar Per phase kv 3 Phase PF 3 Phase kw 3 Phase kvar 3 Phase kva Frequency kwh apacitive kvarh Inductive kvarh Total kvarh Import kvah urrent emand Voltage emand kw emand Peak mps Peak Phase Volts Peak urrent emand Peak Voltage emand Neutral urrent System: Input Harmonics: Operating Temperature: ccuracy: GIM 3 phase, 3 or 4 wire, unbalanced load 0.5% to 120% of range 45-65Hz up to 20th harmonic -10 to 65, <75% RH urrent: ±0.2% of full scale Voltage: ±0.3% of full scale Watts: ±0.4% of full scale Order xample: SI/G asic Unit SI/G100 GIM 100 Meter SI/G200 GIM 200 Meter SI/G300 GIM 300 Meter SI/6400 GIM 400 Meter Power 1 115V 2 230V Voltage Input 1 120/208V 2 120/240V 3 277/480V 4 63/110V urrent Input 1 5 mp Other 1 Modus ommunication 26 IGITL MTRS