Features. MIC5253-x.xBC5 V IN. Ultra-Low-Noise Regulator Application
|
|
- Primrose Banks
- 5 years ago
- Views:
Transcription
1 1mA Low Noise µcap Teeny LDO General Description The is an efficient, CMOS voltage regulator optimized for ultra-low-noise applications. It offers 1.5% initial accuracy, extremely low dropout voltage (165mV at 1mA), and low ground current (typically 95µA at full load). The provides a very low noise output, ideal for RF applications where a clean voltage source is required. A noise bypass pin is also available for further reduction of output noise. Designed specifically for handheld and battery-powered devices, the provides a TTL-logic-compatible enable pin. When disabled, power consumption drops nearly to zero. The also works with low-esr ceramic capacitors, reducing the amount of board space necessary for power applications, critical in handheld wireless devices. Available in the Teeny SC--5 package, the offers a wide range of output voltages. Key features include current limit, thermal shutdown, faster transient response, and an active clamp to speed up device turn-off. Features Input voltage range: 2.7V to 5.5V Teeny SC--5 package Ultra-low output noise: 3µV(rms) 1mA continuous output current, 1mA peak current Stability with ceramic output capacitors Ultralow dropout: 1mA High output accuracy: 1.5% initial accuracy 3.% over temperature Low ground current: 95µA TTL-Logic-controlled enable input Zero off-mode current Thermal shutdown and current limit protection Applications Cellular phones and pagers Cellular accessories Battery-powered equipment Laptop, notebook, and palmtop computers Consumer/personal electronics Typical Application C IN = 1.µF Ceramic Enable Shutdown EN (pin 3) may be connected directly to IN (pin 1). V IN EN -x.xbc V OUT C OUT = 1.µF Ceramic Ultra-Low-Noise Regulator Application, Inc. 21 Fortune Drive San Jose, CA USA tel + 1 (48) 944- fax + 1 (48) November 25 1
2 Ordering Information Part Number Junction Voltage* Standard Marking Pb-Free Marking** Temp. Range Package -1.5BC YC V 4 C to +125 C SC BC YC V 4 C to +125 C SC BC5 71J -1.85YC5 71J 1.85V 4 C to +125 C SC BC YC V 4 C to +125 C SC BC YC V 4 C to +125 C SC BC YC V 4 C to +125 C SC BC YC V 4 C to +125 C SC BC YC V 4 C to +125 C SC--5-3.BC YC V 4 C to +125 C SC BC YC V 4 C to +125 C SC BC YC V 4 C to +125 C SC BC YC V 4 C to +125 C SC--5 * Other voltage options available. Contact Marketing for details. ** Under bar symbol ( _ ) may not be to scale. Pin Configuration EN 3 GND 2 7xx IN BYP OUT SC--5 (C5) Pin Description Pin Number Pin Name Pin Function 1 IN Supply Input. 2 GND Ground. 3 EN Enable/Shutdown (Input): CMOS compatible input. Logic high = enable; logic low = shutdown. Do not leave open. 4 BYP Reference Bypass: Connect external.1µf C BYP 1.µF capacitor to GND to reduce output noise. May be left open. 5 OUT Regulator Output. 2 November 25
3 Absolute Maximum Ratings (1) Supply Input Voltage (V IN )... V to +7V Enable Input Voltage (V EN )... V to +7V Power Dissipation (P D )... Internally Limited (3) Junction Temperature (T J )... 4 C to +125 C Storage Temperature C to +1 C Lead Temperature (soldering, 5 sec.) C ESD Rating (4)... 2kV Electrical Characteristics (5) Operating Ratings (2) V IN = V OUT + 1V, V EN = V IN; I OUT = 1µA; T J = 25 C, bold values indicate 4 C T J +125 C; unless otherwise noted. Input Voltage (V IN ) V to +5.5V Enable Input Voltage (V EN )... V to V IN Junction Temperature (T J )... 4 C to +125 C Thermal Resistance SC--5 (θ JA )...4 C/W Symbol Parameter Conditions Min Typical Max Units V O Accuracy I OUT = 1µA % 3 3 % V LNR Line Regulation V IN = V OUT + 1V to 6V.35.5 %/V V LDR Load Regulation I OUT =.1mA to 1mA, Note % V IN V OUT Dropout Voltage (7) I OUT = ma 1 mv I OUT = 1mA mv I Q Quiescent Current V EN.4V (shutdown).2 1 µa I GND (8) I OUT = ma 75 1 µa I OUT = 1mA 9 1 µa PSRR Ripple Rejection f = 1Hz, C OUT = 1.µF, C BYP =.1µF 66 db f = 1kHz, V IN = V OUT +1, C BYP =.1µF db f = 1kHz, V IN = V OUT +1, C BYP =.1µF 65 db t ON Turn-On Time 3 1 µs I LIM Current Limit V OUT = V ma e n Noise C OUT = 1.µF,, 3 µv(rms) f = 1Hz to 1kHz Enable Input V IL Enable Input Logic-Low Voltage V IN = 2.7V to 5.5V, regulator shutdown.4 V V IH Enable Input Logic-High Voltage V IN = 2.7V to 5.5V, regulator enabled 1.6 V I EN Enable Input Current V IL.4V, regulator shutdown.1 µa V IH 1.6V, regulator enabled.1 µa Thermal Protection Thermal Shutdown Temperature 1 C Thermal Shutdown Hysteresis 1 C Notes: 1. Exceeding the absolute maximum ratings may damage the device. 2. The device is not guaranteed to function outside its operating ratings. 3. The maximum allowable power dissipation of any T A (ambient temperature) is P D(max) = (T J(max) T A )/θ JA. Exceeding the maximum allowable power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. The θ JA of the -x.xbc5 (all versions) is 4 C/W on a PC board (see Thermal Considerations section for further details). 4. Devices are ESD sensitive. Handling precautions recommended. 5. Specification for packaged product only. 6. Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range from.1ma to 1mA. Changes in output voltage due to heating effects are covered by the thermal regulation specification. 7. Dropout Voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. For outputs below 2.7V, dropout voltage is the input-to-output voltage differential with the minimum input voltage 2.7V. Minimum input operating voltage is 2.7V. 8. Ground pin current is the regulator quiescent current. The total current drawn from the supply is the sum of the load current plus the ground pin current. November 25 3
4 Typical Characteristics PSRR (db) Power Supply Rejection Ratio 6 4 1µA 1mA 3 1mA 2 1mA V OUT = 1.8V C OUT = 1µF 1 V = 2.8V C IN BYP =.1µF 1 1k 1k 1k 1M FREQUENCY (Hz) PSRR (db) Power Supply Rejection Ratio µA 1mA 1mA 2 1mA V 1 OUT = 1.8V C OUT = 1µF V IN = 2.8V 1 1k 1k 1k 1M FREQUENCY (Hz) V OUT =1.8V V IN = V OUT + 1V OUTPUT CURRENT (ma) I = 1mA LOAD TEMPERATURE ( C) I = 1µA LOAD TEMPERATURE ( C) I LOAD = 1µA INPUT VOLTAGE (V) I = 1mA LOAD INPUT VOLTAGE (V) OUTPUT VOLTAGE (mv) Dropout Characteristics I LOAD = 1mA 1.4 I 1.2 LOAD = 1µA V = 1.85V OUT INPUT VOLTAGE (V) DROPOUT VOLTAGE (mv) Dropout Voltage V IN = 3.6V V OUT = 2.6V I LOAD = 1mA TEMPERATURE ( C) DROPOUT VOLTAGE (mv) Dropout Voltage 25 C 4 C 125 C V IN = 3.6V V OUT = 2.6V OUTPUT CURRENT (ma) SHORT CIRCUIT CURRENT (ma) Short Circuit Current INPUT VOLTAGE (V) OUTPUT VOLTAGE (V) vs. Temperature 2.55 I LOAD = 1µA V OUT = 2.6V V IN = 3.6V TEMPERATURE ( C) 4 November 25
5 Functional Characteristics Line Transient Response Load Transient Response Input Voltage (1V/div) 5V 4V C IN = 1µF Ceramic C OUT = 1µF Ceramic I OUT = 1µA (2mV/div) 1mA (mv/div) Output Current (ma/div) 1µA C IN = 1µF Ceramic C OUT = 1µF Ceramic V IN = 4V TIME (µs/div) TIME (5µs/div) Enable Pin Delay Shutdown Delay Enable Voltage (1V/div) C IN = 1µF Ceramic C OUT = 1µF Ceramic I OUT = 1µA C IN = 1µF Ceramic C OUT = 1µF Ceramic V IN = 4V (mv/div) (mv/div) Enable Voltage (1V/div) TIME (5µs/div) TIME (µs/div) November 25 5
6 Block Diagram IN Reference Voltage Startup/ Shutdown Control Quickstart/ Noise Cancellation EN BYP Thermal Sensor Undervoltage Lockout FAULT Error Amplifier Current Amplifier ACTIVE SHUTDOWN OUT GND 6 November 25
7 Applications Information Enable/Shutdown The comes with an active-high enable pin that allows the regulator to be disabled. Forcing the enable pin low disables the regulator and sends it into a zero off-modecurrent state. In this state, current consumed by the regulator goes nearly to zero. Forcing the enable pin high enables the output voltage. This part is CMOS and the enable pin cannot be left floating; a floating enable pin may cause an indeterminate state on the output. Input Capacitor The is a high performance, high bandwidth device. Therefore, it requires a well-bypassed input supply for optimal performance. A 1µF capacitor is required from the input to ground to provide stability. Low-ESR ceramic capacitors provide optimal performance at a minimum of space. Additional high-frequency capacitors, such as small valued NPO dielectric type capacitors, help filter out high frequency noise and are good practice in any RF based circuit. Output Capacitor The requires an output capacitor for stability. The design requires 1µF or greater on the output to maintain stability. The design is optimized for use with low-esr ceramic chip capacitors. High ESR capacitors may cause high frequency oscillation. The maximum recommended ESR is 3mΩ. The output capacitor can be increased, but performance has been optimized for a 1µF ceramic output capacitor and does not improve significantly with larger capacitance. X7R/X5R dielectric-type ceramic capacitors are recommended because of their temperature performance. X7Rtype capacitors change capacitance by 15% over their operating temperature range and are the most stable type of ceramic capacitors. Z5U and Y5V dielectric capacitors change value by as much as % and 6%, respectively, over their operating temperature ranges. To use a ceramic chip capacitor with Y5V dielectric, the value must be much higher than an X7R ceramic capacitor to ensure the same minimum capacitance over the equivalent operating temperature range. Bypass Capacitor A capacitor can be placed from the noise bypass pin to ground to reduce output voltage noise. The capacitor bypasses the internal reference. A.1µF capacitor is recommended for applications that require low-noise outputs. The bypass capacitor can be increased, further reducing noise and improving PSRR. Turn-on time increases slightly with respect to bypass capacitance. A unique quick-start circuit allows the to drive a large capacitor on the bypass pin without significantly slowing turn-on time. Refer to the Typical Characteristics section for performance with different bypass capacitors. Active Shutdown The also features an active shutdown clamp, which is an N-channel MOSFET that turns on when the device is disabled. This allows the output capacitor and load to discharge, de-energizing the load. No-Load Stability The will remain stable and in regulation with no load unlike many other voltage regulators. This is especially important in CMOS RAM keep-alive applications. Thermal Considerations The is designed to provide 1mA of continuous current in a very small package. Maximum ambient operating temperature can be calculated based on the output current and the voltage drop across the part. Given that the input voltage is 5.V, the output voltage is 2.9V, and the output current = 1mA. The actual power dissipation of the regulator circuit can be determined using the equation: P D = (V IN V OUT ) I OUT + V IN I GND Because this device is CMOS and the ground current is typically <1µA over the load range, the power dissipation contributed by the ground current is < 1% and can be ignored for this calculation. P D = (5.V 2.9V) 1mA P D =.21W To determine the maximum ambient operating temperature of the package, use the junction-to-ambient thermal resistance of the device and the following basic equation: T J(max) T A P D(max) = θ JA T J (max) = 125 C, the max. junction temperture of the die θ JA thermal resistance = 4 C/W Table 1 shows junction-to-ambient thermal resistance for the in the SC- package. Package θ JA Recommended θ JA 1" Sq. θ JC Minimum Footprint Copper Clad SC--5 (C5) 4 C/W 325 C 2 C/W Table 1. Thermal Resistance Substituting P D for P D (max) and solving for the ambient operating temperature will give the maximum operating conditions for the regulator circuit. The junction-to-ambient thermal resistance for the minimum footprint is 4 C/W, from Table 1. The maximum power dissipation must not be exceeded for proper operation. For example, when operating the -2.9BC5 at an input voltage of 5.V and 1mA load with a minimum footprint layout, the maximum ambient operating temperature T A can be determined as follows:.21w 125 C = T 4 C/W T A = 41 C A November 25 7
8 Therefore, a 2.9V application at 1mA of output current can accept an ambient operating temperature of 41 C in a SC- package. For a full discussion of heat sinking and thermal effects on voltage regulators, refer to the Regulator Thermals section of s Designing with Low-Dropout Voltage Regulators handbook. This information can be found on 's website at: 8 November 25
9 Package Information.65 (.256) BSC 1.35 (.53) 1.15 (.45) 2.4 (.94) 1. (.71) 2.2 (.87) 1. (.71) 1. (.39). (.32) 1.1 (.43). (.32) DIMENSIONS: MM (INCH).18 (.7).1 (.4).3 (.12).15 (.6).1 (.4). (.) 5-Pin SC--5 (C5).3 (.12).1 (.4) MICREL, INC FORTUNE DRIVE SAN JOSE, CA USA TEL + 1 (48) 944- FAX + 1 (48) WEB The information furnished by in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by for its use. reserves the right to change circuitry and specifications at any time without notification to the customer. Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser s use or sale of Products for use in life support appliances, devices or systems is at Purchaser s own risk and Purchaser agrees to fully indemnify for any damages resulting from such use or sale. 24, Incorporated. November 25 9
Features. Applications V IN ENABLE SHUTDOWN. C IN = 1.0µF
300mA High PSRR, Low Noise µcap CMOS LDO General Description The is an efficient CMOS voltage regulator optimized for low-noise applications. It offers 1.5% initial accuracy, low dropout voltage (300mV
More informationFeatures ENABLE SHUTDOWN. Ultra-Low-Noise Regulator Application
5mA Low Noise µcap CMOS LDO General Description The is an efficient, precise CMOS voltage regulator optimized for ultra-low-noise applications. It offers % initial accuracy, extremely-low dropout voltage
More informationFeatures. Applications
MIC532 15mA ULDO in Ultra-Small 1.2mm x 1.6mm Thin MLF General Description The MIC532 is an ultra-small, ultra-low dropout CMOS regulator, ULDO that is ideal for today s most demanding portable applications
More informationFeatures. Applications. V OUT
MIC535 5mA µcap Ultra-Low Dropout LDO Regulator General Description The MIC535 is a high-performance, 5mA LDO regulator, offering extremely high PSRR and very low noise while consuming low ground current.
More informationFeatures. MIC5318-x.xYMT EN BYP GND. Portable Application
High Performance 3mA µcap ULDO General Description The is a high performance, single output ultra low drop-out (ULDO ) regulator, offering low total output noise in an ultra-small Thin MLF package. The
More informationFeatures. MIC5301-x.xYMT EN BYP GND. Portable Application
Single, 1mA µcap ULDO General Description The is a high performance, single output ultra low LDO (ULDO ) regulator, offering low total output noise. The is capable of sourcing 1mA output current and offers
More informationMIC5385. Features. General Description. Applications. Typical Application. Ultra Small Triple 150mA Output LDO
Ultra Small Triple 1 Output LDO General Description The is an advanced general purpose triple linear regulator offering high power supply rejection (PSRR) in an ultra-small 2mm x 2mm 8 pin Thin MLF package.
More informationMIC5248. Features. General Description. Applications. Typical Application. 150mA µcap CMOS LDO Regulator w/power Good VIN VOUT C OUT GND
150mA µcap CMOS LDO Regulator w/power Good General Description The is an efficient, general purpose 1.2V CMOS voltage regulator with a power good output function. The offers better than 3%initial accuracy,
More informationMIC5387. Features. General Description. Applications. Typical Application. Ultra-Small Triple 150mA Output LDO
Ultra-Small Triple Output LDO General Description The is an advanced, general-purpose, triple linear regulator offering high power supply rejection (PSRR) in an ultra-small, 6-pin, 1.6mm x 1.6mm Thin MLF
More informationFeatures. Applications
High PSRR Low Noise 300mA µcap Ultra-Low Dropout LDO Regulator General Description The is a high-performance, 300mA LDO regulator, offering extremely high PSRR and very low noise while consuming low ground
More informationFeatures. Applications. RF Transceiver
15mA µcap Dual LDO Regulator General Description The is a dual 15mA LDO in tiny 2.5mm x 2.5mm MLF packaging ideal for applications where cost is the priority. The is ideal for any application in portable
More informationMIC2215. Features. General Description. Applications. Typical Application. Triple High PSRR, Low Noise µcap LDO
Triple High PSRR, Low Noise µcap LDO General Description The is a high performance, triple LDO voltage regulator, with each regulator capable of providing 250mA continuous output current. Ideal for battery
More informationFeatures ENABLE SHUTDOWN. Ultra-Low-Noise Regulator Application
MIC547 5mA Low-Voltage µcap Linear Regulator General Description The MIC547 is an efficient and precise, low-voltage CMOS voltage regulator optimized for ultra-low noise applications. The MIC547 offers
More informationMIC5309. Features. General Description. Applications. Typical Application. Low V IN /V OUT 300mA High PSRR ULDO with Ultra-Low IQ
Low V IN /V OUT 3mA High PSRR ULDO with Ultra-Low IQ General Description The is a high performance, µcap low dropout regulator, offering ultra-low operating current while maintaining very fast transient
More informationMIC5225. General Description. Features. Applications. Typical Application. Ultra-Low Quiescent Current 150mA µcap Low Dropout Regulator
Ultra-Low Quiescent Current 15mA µcap Low Dropout Regulator General Description The is a 15mA highly accurate, low dropout regulator with high input voltage and ultra-low ground current. This combination
More informationMIC5365/6. General Description. Features. Applications. Typical Application. High-Performance Single 150mA LDO
High-Performance Single 150mA LDO General Description The is an advanced general purpose linear regulator offering high power supply rejection (PSRR) in an ultra-small 1mm 1mm package. The MIC5366 includes
More informationMIC5317. Features. General Description. Applications. Typical Application. High-Performance Single 150mA LDO
High-Performance Single 150mA LDO General Description The is a high performance 150mA low dropout regulator offering high power supply rejection (PSRR) in an ultra-small 1mm 1mm package for stringent space
More informationMIC5238. General Description. Features. Applications. Typical Application. Ultra-Low Quiescent Current, 150mA µcap LDO Regulator
Ultra-Low Quiescent Current, 150mA µcap LDO Regulator General Description The is an ultra-low voltage output, 150mA LDO regulator. Designed to operate in a single supply or dual supply mode, the consumes
More informationFeatures. Applications. RF Power Supply Circuit
High Performance, Low Noise Dual 500mA ULDO General Description The is a tiny Dual Ultra Low Dropout (ULDO ) linear regulator ideally suited for portable electronics due to its low output noise. The provides
More informationMIC5524. Features. General Description. Applications. Typical Application. High-Performance 500mA LDO in Thin DFN Package
High-Performance 500mA LDO in Thin DFN Package General Description The is a low-power, µcap, low dropout regulator designed for optimal performance in a very-small footprint. It is capable of sourcing
More informationMIC5331. General Description. Features. Applications. Typical Application. Micro-Power High Performance Dual 300mA ULDO
Micro-Power High Performance Dual 300mA ULDO General Description The is a tiny dual low quiescent current LDO ideal for applications that are power sensitive. The integrates two high performance, 300mA
More informationMIC5316. General Description. Features. Applications. Typical Application. Low Voltage Dual 300mA LDO with Power on Reset and Voltage Select
Low Voltage Dual 300mA LDO with Power on Reset and Voltage Select General Description The is a high performance, dual low input voltage, low dropout regulator with Power On Reset (POR) and voltage select.
More informationMIC5375/6/7/8. General Description. Features. Applications. Typical Application. High Performance Low Dropout 150mA LDO
High Performance Low Dropout 150mA LDO General Description The is an advanced general purpose linear regulator offering low dropout in an ultra small package. The MIC5375/6 provides fixed output voltage
More informationFeatures. Applications
High Input Voltage Low IQ µcap LDO Regulator General Description The is a 100mA highly accurate, low dropout regulator with high input voltage and ultra-low ground current. This combination of high voltage
More informationFeatures. Enable Shutdown 2. LAx. Regulator Circuit
MIC53 MIC53 Teeny SC-7 µcap Low-Dropout Regulator Final Information General Description The MIC53 is a µcap 8mA linear voltage regulator in the Teeny SC-7 package. Featuring half the footprint of the standard
More informationMIC5206. General Description. Features. Applications. Typical Application. 150mA Low-Noise LDO Regulator
MIC526 5mA Low-Noise LDO Regulator General Description The MIC526 is an efficient linear voltage regulator with very low dropout voltage (typically 7 at light loads and 65 at 5mA), and very low ground
More informationMIC5333. General Description. Features. Applications. Typical Application. Micro-Power High Performance Dual 300mA ULDO with Dual POR
Micro-Power High Performance Dual 300mA ULDO with Dual POR General Description The is a tiny dual low quiescent current LDO ideal for applications that are power sensitive. The integrates two high performance,
More informationMIC5380/1. General Description. Features. Applications. Typical Application. High Performance Dual 150mA LDO 1mm x 1mm Thin MLF
High Performance Dual 15mA LDO 1mm x 1mm Thin MLF General Description The is an advanced dual LDO ideal for powering space constrained portable devices. The provides two independently controlled, high
More informationMIC General Description. Features. Applications: Typical Application. 1A High Speed Low VIN LDO
1A High Speed Low VIN LDO General Description The is a high speed, Low V IN LDO capable of delivering up to 1A and designed to take advantage of point of load applications that use multiple supply rails
More informationFeatures V OUT C BYP. Ultra-Low-Noise Regulator Application
MIC525 MIC525 5mA Low-Noise LDO Regulator Final Information General Description The MIC525 is an efficient linear voltage regulator with ultralow-noise output, very low dropout voltage (typically 7mV at
More informationFeatures. Applications. Adjustable Regulator Application. (*See Minimum Load Current Section)
3A, Low Voltage µcap LDO Regulator General Description The is a 3A low-dropout linear voltage regulator that provides a low voltage, high current output with a minimum of external components. It offers
More informationMIC5388/9. Features. General Description. Applications. Typical Application. Dual 200mA Peak LDO in Wafer Level Chip Scale Package
Dual 2mA Peak LDO in Wafer Level Chip Scale Package General Description The is an advanced dual LDO ideal for powering general purpose portable devices. The provides two independently-controlled, highperformance,
More informationFeatures. Applications. V OUT Enable Shutdown
MIC53 μcap 8mA Low-Dropout Regulator General Description The MIC53 is a µcap 8mA linear voltage regulator with very low dropout voltage (typically mv at light loads and 3mV at 8mA) and very low ground
More informationMIC5332. Features. General Description. Applications. Typical Application. Micro-Power, High-Performance Dual 300mA ULDO
Micro-Power, High-Performance Dual 300mA ULDO General Description The is a tiny, dual, low quiescent current LDO ideal for applications that are power sensitive. The integrates two high-performance 300mA
More informationMIC5501/2/3/4. General Description. Features. Applications. Typical Application. Single 300mA LDO in 1.0mm 1.0mm DFN Package
Single 300mA LDO in 1.0mm 1.0mm DFN Package General Description The is an advanced general-purpose LDO ideal for powering general-purpose portable devices. The family of products provides a highperformance
More informationMIC5396/7/8/9. General Description. Features. Applications. Typical Application. Low-Power Dual 300mA LDO in 1.2mm x 1.
Low-Power Dual 300mA LDO in 1.2mm x 1.6mm Extra Thin DFN General Description The is an advanced dual LDO ideal for powering general purpose portable devices. The provides two high-performance, independent
More informationMIC5235. General Description. Features. Applications. Typical Application. Ultra-Low Quiescent Current, 150mA µcap LDO Regulator
MIC535 Ultra-Low Quiescent Current, 5mA µcap LDO Regulator General Description The MIC535 is a 5mA highly accurate, low dropout regulator with high input voltage and ultra-low ground current. This combination
More informationMIC5370/1. Features. General Description. Applications. Typical Application. High-Performance Dual 150mA LDO 1.6mm x 1.
High-Performance Dual 15mA LDO 1.6mm x 1.6mm General Description The is an advanced dual LDO ideal for powering general purpose portable devices. The provides two independently-controlled, highperformance
More informationMIC5216. General Description. Features. Applications. Typical Application. 500mA-Peak Output LDO Regulator
500mA-Peak Output LDO Regulator General Description The is an efficient linear voltage regulator with high peak output current capability, very low dropout voltage, and better than 1% output voltage accuracy.
More informationFeatures. Applications
Dual 500mA µcap Low Dropout, Micropower Linear Regulator General Description The is an advanced dual, micropower, low dropout linear regulator. The provides low quiescent current operation, using only
More informationFeatures. RF Power Supply Circuit
Dual 300mA µcap LDO in 2mm x 2mm MLF General Description The is a tiny Dual Ultra Low Dropout (ULDO ) linear regulator ideally suited for portable electronics due to its high power supply ripple rejection
More informationMIC General Description. Features. Applications. Typical Application. 5A, Low V IN, Low V OUT µcap LDO Regulator
MIC6952, Low V IN, Low V OUT µcap LDO Regulator General Description The MIC6952 is a, low dropout linear regulator that provides low voltage high current outputs with a minimum of external components.
More informationMIC5207. General Description. Features. Applications. Typical Application. 180mA Low-Noise LDO Regulator
180mA Low-Noise LDO Regulator General Description The is an efficient linear voltage regulator with ultra-low-noise output, very low dropout voltage (typically 17 at light loads and 165 at 150mA), and
More informationMIC37150/51/52/53. General Description. Features. Applications. Typical Application. 1.5A, Low Voltage µcap LDO Regulator
1.5A, Low Voltage µcap LDO Regulator General Description The Micrel is a 1.5A low-dropout linear voltage regulator that provides a low voltage, high current output with a minimum of external components.
More informationMIC3975. General Description. Features. Applications. Ordering Information. Typical Applications. 750mA µcap Low-Voltage Low-Dropout Regulator
MIC3975 750mA µcap Low-Voltage Low-Dropout Regulator General Description The MIC3975 is a 750mA low-dropout linear voltage regulators that provide low-voltage, high-current output from an extremely small
More informationFeatures. Applications
MIC9431 2mA LDO with Ripple Blocker Technology General Description The MIC9431 Ripple Blocker is a monolithic integrated circuit that provides low-frequency ripple attenuation (switching noise rejection)
More informationFeatures. MIC2212-xxBML VOUT2 POR CBYP SET GND. MIC2212 Typical Cell Phone Application
MIC2212 Dual µcap LDO and Power-On Reset General Description The MIC2212 is a dual µcap low dropout regulator with power-on reset circuit. The first regulator is capable of sourcing 15mA, while the second
More informationGM6155 GM6155V1.01. Description. Features. Application. Typical Application Circuits. 150mA LOW NOISE CMOS LDO WITH ENABLE FUNCTION
Description GM6155 is a high efficient CMOS LDO with features as such ultra low noise output, ultra low dropout voltage (typically 17mV at light load and 165mV at 50mA load), and low ground current (600µA
More informationMIC Features. General Description. Applications. Typical Application. 1.5A, Low-Voltage µcap LDO Regulator
1.5A, Low-Voltage µcap LDO Regulator General Description The Micrel is a 1.5A low-dropout linear voltage regulator that provides a low-voltage, high-current output with a minimum of external components.
More informationMIC69101/103. General Description. Features. Applications. Typical Application. Single Supply V IN, LOW V IN, LOW V OUT, 1A LDO
MIC6911/13 Single Supply V IN, LOW V IN, LOW V OUT, 1A LDO General Description The MIC6911/13 is the 1A output current member of the MIC69xxx family of high current, low voltage regulators, which support
More informationMIC5310. General Description. Features. Applications. Typical Application. Dual 150mA µcap LDO in 2mm x 2mm MLF
Dual 15mA µcap LDO in 2mm x 2mm MLF General Description The is a tiny Dual Ultra Low Dropout (ULDO ) linear regulator ideally suited for portable electronics due to its high power supply ripple rejection
More informationFeatures. Applications. Portable Application
500mA LDO in 1.6mm 1.6mm Package General Description The is a high-performance, single-output, ultralow LDO (ULDO ) regulator, offering a low total output noise of 30μV RMS. The is capable of sourcing
More informationFeatures MIC5236 GND. Regulator with Adjustable Output
MIC56 Low Quiescent Current µcap LDO Regulator General Description The MIC56 is a low quiescent current, µcap low-dropout regulator. With a maximum operating input voltage of V and a quiescent current
More informationMIC5271. Applications. Low. output current). Zero-current off mode. and reduce power. GaAsFET bias Portable cameras. le enable pin, allowing the user
µcap Negative Low-Dropout Regulator General Description The is a µcap 100mA negativee regulator in a SOT-23-this regulator provides a very accurate supply voltage for applications that require a negative
More informationMIC69151/153. General Description. Features. Applications. Typical Application. Single Supply V IN, Low V IN, Low V OUT, 1.5A LDO
Single Supply V IN, Low V IN, Low V OUT, 1.5A LDO General Description The is the 1.5A output current member of the MIC69xxx family of high current, low voltage regulators, which support currents of 1A,
More informationRT9187C. 600mA, Ultra-Low Dropout, CMOS Regulator. General Description. Features. Applications. Ordering Information. Pin Configurations (TOP VIEW)
600mA, Ultra-Low Dropout, CMOS Regulator General Description The is a high-performance, 600mA LDO regulator, offering extremely high PSRR and ultra-low dropout. This chip is ideal for portable RF and wireless
More informationFeatures. Applications. Battery-Powered Regulator Application
180mA Low-Noise LDO Regulator General Description The is an efficient linear voltage regulator with ultra-low-noise output, very low dropout voltage (typically 17 at light loads and 165 at 150mA), and
More informationFeatures. Applications V IN C IN
3.A, Low-Voltage µcap LDO Regulator General Description The Micrel is a 3.A low-dropout linear voltage regulator that provides a low-voltage, high-current output with a minimum number of external components.
More informationFeatures. Applications. Camera DSP Power Supply Circuit
High-Performance Dual 150mA LDO General Description The is a tiny dual low-dropout linear regulator ideally suited for portable electronics. It is ideal for general purpose/digital applications which require
More informationFeatures. Applications. Figure 1. Typical Application Circuit
3A, Low Voltage, Adjustable LDO Regulator with Dual Input Supply General Description The is a high-bandwidth, low-dropout, 3A voltage regulator ideal for powering core voltages of lowpower microprocessors.
More informationMIC5202. Dual 100mA Low-Dropout Voltage Regulator. Features. General Description. Pin Configuration. Ordering Information. Typical Application
MIC MIC Dual ma Low-Dropout Voltage Regulator Preliminary Information General Description The MIC is a family of dual linear voltage regulators with very low dropout voltage (typically 7mV at light loads
More informationRT mA, Low Input Voltage, Low Dropout, Low Noise Ultra- Fast Without Bypass Capacitor CMOS LDO Regulator. General Description.
RT9030 150mA, Low Input Voltage, Low Dropout, Low Noise Ultra- Fast Without Bypass Capacitor CMOS LDO Regulator General Description The RT9030 is a high-performance, 150mA LDO regulator, offering extremely
More informationRT9187B. 600mA, Ultra-Low Dropout, Ultra-Fast CMOS LDO Regulator. General Description. Features. Applications. Ordering Information RT9187B
6mA, Ultra-Low Dropout, Ultra-Fast CMOS LDO Regulator General Description The is a high-performance, 6mA LDO regulator, offering extremely high PSRR and ultra-low dropout. This chip is ideal for portable
More informationRT mA, Low Input Voltage, Low Dropout, Low Noise Ultra- Fast Without Bypass Capacitor CMOS LDO Regulator. General Description.
Applications CDMA/GSM Cellular Handsets Portable Information Appliances Laptop, Palmtops, Notebook Computers Hand-Held Instruments Mini PCI & PCI-Express Cards PCMCIA & New Cards RT9030 150mA, Low Input
More informationMIC General Description. Features. Applications. Typical Application. 1.5A Low Voltage LDO Regulator w/dual Input Voltages
MIC4915 1.5A Low oltage LDO Regulator w/dual Input oltages General Description The MIC4915 is a high-bandwidth, low-dropout, 1.5A voltage regulator ideal for powering core voltages of lowpower microprocessors.
More informationFeatures. Applications
MIC9431 2mA LDO with Ripple Blocker Technology General Description The MIC9431 Ripple Blocker is a monolithic integrated circuit that provides low-frequency ripple attenuation (switching noise rejection)
More informationMIC37100/37101/ General Description. Features. Applications. Typical Applications. 1A Low-Voltage µcap LDO Regulator
MIC37/37/37 MIC37/37/37 A Low-Voltage µcap LDO Regulator General Description The MIC37, MIC37, and MIC37 are A low-dropout, linear voltage regulators that provide low-voltage, high-current output from
More informationRT mA, Low Dropout, Low Noise Ultra-Fast With Soft Start CMOS LDO Regulator. General Description. Features. Applications. Ordering Information
Applications Digital Still Camera CDMA/GSM Cellular Handsets Portable Information Appliances Laptop, Palmtops, Notebook Computers Mini PCI & PCI-Express Cards PCMCIA & New Cards Pin Configurations RT92
More informationMIC General Description. Features. Applications. Typical Application. 3A Low Voltage LDO Regulator with Dual Input Voltages
3A Low Voltage LDO Regulator with Dual Input Voltages General Description The is a high-bandwidth, low-dropout, 3.0A voltage regulator ideal for powering core voltages of lowpower microprocessors. The
More informationMIC5374/84. Features. General Description. Applications. Typical Application. Triple 200mA µcap LDO and 1mA RTC LDO in 2.5mm x 2.
Triple 2mA µcap LDO and 1mA RTC LDO in 2.5mm x 2.5mm Thin MLF General Description The is a four output device with three 2mA LDOs and a real time clock (RTC) 1mA LDO which is ideal for application processor
More informationLow Noise 300mA LDO Regulator General Description. Features
Low Noise 300mA LDO Regulator General Description The id9301 is a 300mA with fixed output voltage options ranging from 1.5V, low dropout and low noise linear regulator with high ripple rejection ratio
More information200mA Low Power Consumption CMOS LDO Regulator CLZ6821/22
General Description The CLZ6821 is a positive LDO regulator designed on patent pending CMOS circuit technologies. The device attains high ripple rejection ratio and superior line and load transient response
More informationRT9198/A. 300mA, Low Noise, Ultra-Fast CMOS LDO Regulator. General Description. Ordering Information RT9198/A- Features. Marking Information
RT9198/A 3mA, Low Noise, Ultra-Fast CMOS LDO Regulator General Description The RT9198/A is designed for portable RF and wireless applications with demanding performance and space requirements. The RT9198/A
More informationMIC5373/83. Features. General Description. Applications. Typical Application. Triple 200mA µcap LDO in 2.5mm x 2.5mm Thin MLF
Triple 2mA µcap LDO in 2.5mm x 2.5mm Thin MLF General Description The is a triple output device with three 2mA LDOs which is ideal for application processor support in mobile platforms. The MIC5373 provides
More informationRT mA, Ultra-Low Noise, Ultra-Fast CMOS LDO Regulator. General Description. Features. Applications. Ordering Information. Marking Information
3mA, Ultra-Low Noise, Ultra-Fast CMOS LDO Regulator General Description The RT9193 is designed for portable RF and wireless applications with demanding performance and space requirements. The RT9193 performance
More information150mA Low Noise LDO Regulator
5mA Low Noise LDO Regulator TJ525 FEATURES Ultra Low Noise Output High Output Voltage Accuracy Guaranteed 5mA Output Maximum Output Voltage of Adjustable type is 8.5V. Low Quiescent Current Low Dropout
More informationRT mA Dual LDO Regulator. General Description. Features. Applications. Ordering Information. Pin Configurations (TOP VIEW) Marking Information
RT9055 300mA Dual LDO Regulator General Description The RT9055 is a dual channel, low noise, and low dropout regulator sourcing up to 300mA at each channel. The output voltage range is from 0.9V to 3.5V
More informationMIC37501/ General Description. Features. Applications. Typical Applications. 5A, Low Voltage μcap LDO Regulator
MIC375/375, Low Voltage μcap LDO Regulator General Description The MIC375 and MIC375 are, low dropout linear voltage regulator that provide low voltage, high current outputs with a minimum of external
More informationRT mA, Low Dropout, Low Noise Ultra-Fast With Soft Start CMOS LDO Regulator. General Description. Features. Applications
RT92 5mA, Low Dropout, Low Noise Ultra-Fast With Soft Start CMOS LDO Regulator General Description The RT92 is a high-performance, 5mA LDO regulator, offering extremely high PSRR and ultra-low dropout,
More informationid id mA, Low Dropout, Low Noise Ultra-Fast With Soft Start CMOS LDO Regulator Features General Description Applications
500mA, Low Dropout, Low Noise Ultra-Fast With Soft Start CMOS LDO Regulator General Description The is a 500mA, low dropout and low noise linear regulator with high ripple rejection ratio. It has fixed
More informationFeatures. Applications
3.0A, Low-Voltage µcap LDO Regulator General Description The Micrel is a 3.0A low-dropout linear voltage regulator that provides a low voltage, high current output with a minimum number of external components.
More informationMIC Features. General Description. Applications. Ordering Information. 3A Fast-Response LDO Regulator for USB
3A Fast-Response LDO Regulator for USB General Description The is a 3A, fast response, low-dropout (LDO) voltage regulator. Using Micrel s proprietary Super βeta PNP process, the offers exceptional dropout
More informationMP20249 Dual, Ultra-Low Noise, High PSRR 200mA Linear Regulator
The Future of Analog IC Technology DESCRIPTION The MP2249 is a dual-channel, ultra-low noise, low dropout and high PSRR linear regulator. Fixed output voltage options are available between 1.2V to 3.3V
More informationFeatures MIC ERROR FLAG OUTPUT V IN 3.3V IN V OUT 2.5V 3.3V OUT GND
MIC395/3951 5A µcap Low-Voltage Low-Dropout Regulator General Description The MIC395 and MIC3951 are 5A low-dropout linear voltage regulators that provide a low-voltage, high-current output with a minimum
More information150mA Low-Noise LDO Regulator
50mA Low-Noise LDO Regulator Product Description The GS265 is an efficient linear voltage regulator with ultra low-noise output, very low dropout voltage (typically 7mV at light loads and 65mV at 50mA),
More informationid9309 Ultra-Low Noise Ultra-Fast 300mA LDO Regulator Features
Ultra-Low Noise Ultra-Fast 300mA LDO Regulator General Description The id9309 is a 300mA, low dropout and low noise linear regulator with high ripple rejection ratio and fast turn-on time. It has fixed
More informationMIC37110/MIC37112 MIC37120/MIC37122
High-Performance, Low-Noise, 1A LDOs General Description The and are high-performance, low-noise, low dropout regulators. Each of these LDOs is capable of sourcing 1A output current, offers high power
More informationFeatures. 100k MIC39101 IN OUT GND. 2.5V/1A Regulator with Error Flag
MIC391/3911/3912 MIC391/3911/3912 1A Low-Voltage Low-Dropout Regulator General Description The MIC391, MIC3911, and MIC3912 are 1A low-dropout linear voltage regulators that provide low-voltage, high-current
More informationRT mA, Low Dropout, Low Noise Ultra-Fast Without Bypass Capacitor CMOS LDO Regulator. Features. General Description.
5mA, Low Dropout, Low Noise Ultra-Fast Without Bypass Capacitor CMOS LDO Regulator General Description The RT913 is a high-performance, 5mA LDO regulator, offering extremely high PSRR and ultra-low dropout.
More informationRT mA, Ultra-Low Noise, Ultra-Fast CMOS LDO Regulator. General Description. Features. Applications. Ordering Information. Marking Information
3mA, Ultra-Low Noise, Ultra-Fast CMOS LDO Regulator General Description The is designed for portable RF and wireless applications with demanding performance and space requirements. The performance is optimized
More informationRT mA, 0.5% Accuracy Low Dropout, Ultra Low Noise Voltage Regulator. Features. General Description. Applications. Ordering Information
3mA,.5% Accuracy Low Dropout, Ultra Low Noise Voltage Regulator General Description The RT95 is a high-performance, 3mA LDO regulator, offering extremely high PSRR and ultra-low dropout. The RT95 is Ideal
More informationRT9043- High PSRR, Low Dropout, 400mA Adjustable LDO Regulator. Features. General Description. Applications. Ordering Information. Pin Configurations
High PSRR, Low Dropout, 400mA Adjustable LDO Regulator General Description The RT9043 is a high-performance, 400mA LDO regulator, offering high PSRR and low dropout. The quiescent current is as low as
More informationMIC3385. General Description. Features. Applications. Typical Application. 8MHz Inductorless Buck Regulator with LDO Standby Mode
8MHz Inductorless Buck Regulator with LDO Standby Mode General Description The Micrel is a high efficiency inductorless buck regulator that features a LOWQ LDO standby mode that draws only 18µA of quiescent
More informationFeatures. Applications
High-Current Low-Dropout Regulators General Description The is a high current, high accuracy, lowdropout voltage regulators. Using Micrel's proprietary Super βeta PNP process with a PNP pass element, these
More informationMIC2296. General Description. Features. Applications. High Power Density 1.2A Boost Regulator
High Power Density 1.2A Boost Regulator General Description The is a 600kHz, PWM dc/dc boost switching regulator available in a 2mm x 2mm MLF package option. High power density is achieved with the s internal
More informationRT μA I Q, 250mA Low-Dropout Linear Regulator. General Description. Features
RT9073 1μA I Q, 250mA Low-Dropout Linear Regulator General Description The RT9073 is a low-dropout (LDO) voltage regulators with enable function that operates from 1.2V to 5.5V. It provides up to 250mA
More informationFeatures. Applications
MIC9431 2mA LDO with Ripple Blocker Technology General Description The MIC9431 Ripple Blocker is a monolithic integrated circuit that provides low-frequency ripple attenuation (switching noise rejection)
More informationACE533J 500mA, Micropower, VLDO Linear Regulator
Description The ACE533J series are VLDO (very low dropout) linear regulators designed for low power portable applications. Typical output noise is only 100μV RMS (Fixed Output, V OUT =1.0V) and maximum
More informationMP2009 Ultra-Low-Noise Low-Dropout, 120mA Linear Regulator
MP2009 Ultra-Low-Noise Low-Dropout, 120mA Linear Regulator DESCRIPTION The MP2009 is an ultra low noise, low dropout linear regulator. The output voltage of MP2009 ranges from 1.5V to 4.5V in 100mV increments
More informationMIC2245. Features. General Description. Applications. Typical Application. 4MHz PWM Synchronous Buck Regulator with LDO Standby Mode
4MHz PWM Synchronous Buck Regulator with LDO Standby Mode General Description The Micrel is a high efficiency 4MHz pulse width modulated (PWM) synchronous buck (stepdown) regulator that features a LOWQ
More information