Radio Shield RS-UVPA Rev: D Three band Power Amplifier
|
|
- Dorthy Pierce
- 5 years ago
- Views:
Transcription
1 Radio Shield RS-UVPA Rev: D Three band Power Amplifier Jim Veatch WA2EUJ 1 April 2016
2 TABLE OF CONTENTS 1. INTRODUCTION Specifications Operation INSTALLATION RS-UV3 Rev C and Rev D Hamshield... 7 Appendix A Schematics... 8
3 1. INTRODUCTION Congratulations on your purchase of a RS-UVPA Power Amplifier. The RS-UVPA is designed to interconnect mechanically and electrically with the HobbyPCB RS-UV3, three band, FM transceiver. It is also possible to use the RS-UVPA with other 144/220/440 transmitters or transceivers that provide up to 1 W output. The RX path has a low-noise pre amplifier that can be configured for low gain to overcome amplifier insertion loss or high gain which can improve the noise figure/sensitivity of low performance receivers. The RS-UVPA has control line outputs for each band, capable of keying an external amplifier for higher power operation. 1.1 Specifications Frequency Range (TX) MHz, MHz MHz; (RX) MHz Drive Level 200mW to 1W (may require attenuator adjustment over 0.5W) Output power 5W minimum on 144 and 220 bands; 4W minimum on 440 band Spurious Attenuation Greater than 53 dbc typically 60 dbc Antenna 50 ohms, SWR trip point: 3:1 RX Gain 2-3 db or db, jumper selectable RX Noise Figure 1.5 db maximum DC Power 8 to 15 VDC, 2 Amps maximum during TX < 50mA RX Size - 120mm L X 75mm W X 25mm H 1.2 Operation Once integrated with the transceiver, there is no impact on the operation of the transceiver. RS- UVPA operation is completely transparent, just like its part of the transceiver. The RS-UVPA does provide SWR protection which when tripped, will light the SWR LED and disable the power amp for the remainder of the transmission. Normal operation is resumed when the amplifier is unkeyed. DO NOT operate the RS-UVPA with the antenna directly connected to the PCB unless the RS- UVPA is mounted inside a shielded metal enclosure. Otherwise the RS-UVPA s PCB becomes part of the antenna system which can produce unexpected operation and/or damage to circuit components.
4 2. INSTALLATION This section describes the steps necessary to connect the RS-UVPA to the RS-UV3 and other transceivers. 2.1 RS-UV3 Rev C and Rev D If you are trying to connect the RS-UVPA to a RS-UV3 Rev B contact HobbyPCB Technical Support. Start by removing the power connector and the solder from solder jumper SJ1 as shown: The power connector interferes with the power connector on the amplifier and is redundant. The RS-UVPA will supply the RS-UV3 with power. The solder jumper sends the RF to the SMA jack which is bypassed when using the RS-UVPA. Technically the SMA could be removed but it doesn t interfere mechanically and it is VERY difficult to remove from the board. The solder jumper can be cleared and the power jack removed using solder wick. The next step is to add three headers to the RS-UV3; a 6 pin AMP header, a 2 pin PW header and a 2 pin PA header. Solder a single pin first the make sure the header is fully seated against the PCB and oriented perpendicular to the board before soldering the remaining pin(s). The following picture shows the header locations:
5 Once the headers are installed, it s time to mate the RS-UV3 and RS-UVPA boards. Make sure that the header pins on the radio align with the corresponding sockets on the amp. Put a jumper wire across the PWR-SW connections at this time. The RS-UVPA has a redundant set of PWR- SW contacts
6 The resulting board stack can be mounted in a suitable enclosure using the mounting holes in the PCBs or slide into extruded enclosures designed for 120mm X 75mm boards like a Hammond 1455K1201. HobbyPCB provides an enclosure available on our website. Here is the RS-UV3 and RS-UVPA mounted in a Hammond 1455K1201BK extrusion. The RS-UVPA is supplied with a small plastic cover on the SMA connector. Remove this cover from the SMA connector and place it over the unused SMA connector on the RS-UV3 to prevent (reduce) confusion when attaching the antenna.
7 2.2 Hamshield The RS-UVPA is designed to interface to the Hamshield and provide 5W output and provide a much needed improvement in receiver sensitivity, noise figure and filtering. As soon as we get our hands on one, we ll provide updated info.
8 Appendix A Schematics
9
DEM TC DEM TRANSVERTER CONTROL
DEM TC DEM TRANSVERTER CONTROL The DEM Transverter Control (DEM TC) is the circuit board that controls all transverter functions in the DEMI 2.3 GHz. -10 GHz. transverters. It was designed with many options
More informationINSTALLATION and OPERATION INSTRUCTIONS. FOR FiberLink BI-DIRECTIONAL AMPLIFIER WITH DIVERSITY MW-FBDA-800AB-50W-DIV
INSTALLATION and OPERATION INSTRUCTIONS FOR FiberLink BI-DIRECTIONAL AMPLIFIER WITH DIVERSITY MW-FBDA-800AB-50W-DIV Page 1 of 15 TABLE OF CONTENTS PARA No. PARAGRAPH PAGE No. 1. OVERVIEW 3 2. COMPONENT
More information1.0 General Description
1.0 General Description Figure 1 Plug-N-Play Noise Blanker for the Collins KWM-2/2A The Collins Noise Blanker is designed to be a Plug-N-Play accessory for the Collins KWM-2/2A transceivers. It plugs directly
More informationBroadcast Concepts Inc NW 102 Road Suite 4 Medley FL Tel: : Fax Model P50FM42MH-SMA2 FM Pallet Amplifier Module
Model P50FM42MH-SMA2 FM Pallet Amplifier Module This amplifier module is ideal for driver stages in FM Broadcast transmitters. 86 110MHz 28Volts Pout: 50W CW minimum 40dB Gain Class AB MACOM MRF173 Mosfet
More informationDemo Circuit DC550A Quick Start Guide.
May 12, 2004 Demo Circuit DC550A. Introduction Demo circuit DC550A demonstrates operation of the LT5514 IC, a DC-850MHz bandwidth open loop transconductance amplifier with high impedance open collector
More informationInstallation... 3 Installing The Radio... 3 Ignition Noise Interference... 4 Antenna... 4 External Speaker... 4 Public Address...
TABLE OF CONTENTS CHAPTER 1 Specifications.............................................. 2 PAGE BIG RIG SERIES S 1 MOD PW R 20 0 3 SW R 40 1 5 5 60 1.5 7 10 2 9 20 80 3 30 +20 40 50 +40 100% MAX db +60
More informationA01-eNETL2TUV_Manual_RevH.doc. GE MDS enetl2t/u/v Manual P/N A01 Rev H
GE MDS enetl2t/u/v Manual P/N 05-4186A01 Rev H 05-4186A01 Rev H Page 1 of 7 12/19/2016 Table of Contents 1 Important Information... 3 1.1 RF Exposure... 3 1.2 FCC Approval Notice... 3 1.3 FCC Part 80 Information...
More information18-CHANNEL MOBILE CB TRANSCEIVER MODEL CB-845
18-CHANNEL MOBILE CB TRANSCEIVER MODEL CB-845 INSTRUCTION HANDBOOK RAll JEFFERSOn CITIZEN BAND RADIO MESSAGE TO THE OWNER CONGRATULATIONS! As the new owner of Ray Jefferson Model CB-845 CB Mobile Transceiver,
More informationICOM IC-201 Allmode Transceiver
ICOM IC-201 Allmode Transceiver Alignment Procedure Please note: This procedure is reengineered by myself and may be not in accordance with the original procedure from the manufacturer! So I can t accept
More informationAmeritron ALS-600 Retrofit ALS-600-LPF Assembly Manual
Ameritron ALS-600 Retrofit ALS-600-LPF Assembly Manual FEATURES Automatic band change based on TX frequency. PIN diode QSK RX/TX switch. Temperature controlled FAN for quiet operation. RS-232 serial port
More informationRF Sense SDR Receiver TR Switch Model MFJ-1708B-SDR. RF Sense SDR Receiver TR Switch Model MFJ-1708B-SDR-S CTRL CTRL AUX AUX +12V +12V - + DELAY DELAY
The MFJ-1708B-SDR and the MFJ-1708B-SDRS are RF sensed TR switches with a receive splitter designed to be used with a transceiver and a separate receiver such as the popular SDR receivers. The splitter
More informationEnhancing Your QRP Operating Enjoyment
QRP-DWM Directional-Coupler Watt Meter Preliminary By: W5USJ CyM-Tech Documentation Services Enhancing Your QRP Operating Enjoyment PCB Assembly Top View Addendum: Correct missing toroid ground after installing
More informationBeta-test ED1 PCB installed in I0CG s K1
K1 SSB Modification (Ed.2) This description provides the receiver (RX) modifications, assembly, alignment and operation as a first step. In a second step you can add the remaining transmitter (TX) modifications,
More informationA NEW LIFE FOR THE FT-290R TRANSCEIVER! By F5RCT
A NEW LIFE FOR THE FT-290R TRANSCEIVER! By F5RCT The FT290R is an old amateur radio workhorse which was a very popular transceiver during the 80 s. It is a 2metre multimode portable which can run with
More information200GTL ALIGNMENT REVISION: 1.0 BURKE MODEL: 200GTL REVISION: 1.2 DATE: 02/14/06. Total Pages: 6 pages. Page:1 print date: 9/23/09
ALIGNMENT PROCEDURE MODEL: 200GTL REVISION: 1.2 DATE: 02/14/06 PREPARED BY: BURKE Total Pages: 6 pages Page:1 print date: 9/23/09 1 TEST CONDITION: 200GTL ALIGNMENT INSTRUCTION 1.0. TEST TEMPERTAURE: 77
More informationDual Band Filter Assembly Manual
Dual Band Filter Assembly Manual 12 January 2018 Rev D Version Theory of Operation: The purpose of a Bandpass Filter is to filter out or reject all unwanted signals. The original KN-Q7A Receive Filter
More informationEnhancing Your QRP Operating Enjoyment
QRP-DPM Directional-Coupler Power Meter Preliminary By: W5USJ CyM-Tech Documentation Services Enhancing Your QRP Operating Enjoyment PCB Assembly Top View Addendum: No Changes. The QRP-DPM Directional-
More informationOptiva OTS-2 40 GHz Amplified Microwave Band Fiber Optic Links
5 MHz to 4 GHz Amplified Microwave Transport System The Optiva OTS-2 4 GHz Microwave Band transmitter and receiver are ideal to construct transparent fiber optic links in the 5 MHz to 4 GHz frequency range
More informationPacific Antenna Low Pass Filter Kit
Pacific Antenna Low Pass Filter Kit Description Many basic transmitter and/or transceiver designs have minimal filtering on their output and frequently have significant harmonic content in their signals.
More informationMulti-Channel RS-232 Serial RF Transceiver
RF-232 Multi-Channel RS-232 Serial RF Transceiver The RF-232 subassembly is a multi-channel serial radio transceiver. This device accepts and outputs standard serial data at one of three selectable data
More informationPacific Antenna - Easy TR Switch
Pacific Antenna - Easy TR Switch Kit Description The Easy TR Switch is an RF sensing switch that can be used to switch an antenna between a receiver and transmitter. It also has a second switched pair
More informationQRP to 30-35W HF Packer Amp minihfpa Edition. Beat the downturn in HF conditions! Make your SOTA/NPOTA/WWF activations a success every time!
QRP to 30-35W HF Packer Amp minihfpa Edition Beat the downturn in HF conditions! Make your SOTA/NPOTA/WWF activations a success every time! The minihfpa is a 5th generation HF PackerAmp optimized for your
More informationMobile RF Linear Amplifier
Features High Reliability Design +13.8VDC Operation All Mode (AM, FM, SSB) 10-Meter Amateur Band Coverage Temperature Tracking Class-AB Bias High Output Power / Low Harmonic Content Quad MRF454 Configuration
More informationALACHUA ARES SIMPLEX REPEATER STATION INSTRUCTION MANUAL VERSION 1.0 MARCH
ALACHUA ARES SIMPLEX REPEATER STATION INSTRUCTION MANUAL VERSION 1.0 MARCH 23 2017 1 INTRODUCTION A simplex repeater is nothing more than a digital tape recorder that listens to an FM simplex transceiver,
More informationStatus Tone Generator
Eclipse Series RF Technology rfinfo@rftechnology.com.au January 004 Status Tone Generator Operation and Installation This manual is produced by RF technology Pty Ltd 0/8 Leighton Place, Hornsby 077, Australia
More informationOptiva OTS-2 40 GHz Amplified Microwave Band Fiber Optic Links
2 GHz to 4 GHz Amplified Microwave Transport System The Optiva OTS-2 4 GHz Microwave Band transmitter and receiver are ideal to construct transparent fiber optic links in the 5 MHz to 4 GHz frequency range
More informationSpectrian 2304 MHz SSPA. Garry C. Hess, K3SIW June 11, 2004
Spectrian 2304 MHz SSPA Garry C. Hess, K3SIW June 11, 2004 A solid-state power amplifier (SSPA) manufactured by Spectrian can produce on the order of 200 W linear output 1 at 2304 MHz with little modification.
More informationMFJ-1048 PASSIVE PRESELECTOR. Introduction. Installation
Introduction MFJ-1048 PASSIVE PRESELECTOR The MFJ-1048 is designed to reduce receive overload from strong out of band signals. It contains selective circuits that cover 1.6 to 33 MHz in six steps, providing
More informationQRPme.com Kits. Tx/Tuna Topper. Assembly and Operation Guide. Kits for the QRP and Electronics Hobbyist. Heatsink left off for better assembly viewing
QRPme.com Kits Kits for the QRP and Electronics Hobbyist Tx/Tuna Topper Heatsink left off for better assembly viewing Contents Figures and Illustrations............................... 3 Jumpers............................................
More informationFEU (Front End Unit) for Optic Repeater
FEU (Front End Unit) for Optic Repeater 1. Specification 1.1. All Items Parameter Specification Comments RX1 RX2 TX Frequency Range. 1750.625 ~ 1769.375MHz 1750.625 ~ 1769.375MHz 1840.625 ~ 1859.375MHz
More informationTechnical datasheet. The DTXF-xxx supports South Korean ISM band, 424.7MHz, 447.3MHz and Japanese 429MHz as well as European MHz.
DTXF-xxx Narrow band single channel FSK transmitter The DTXF-xxx series, a narrow band module with 12.5KHz channel spacing, is a high performance transmitter designed for use in industrial & commercial
More informationFlexible Amplifier QSK Keying Interface: Add Turn-Off Delay, and Low-Current Ground or +12V Keying Phil Salas AD5X
Flexible Amplifier QSK Keying Interface: Add Turn-Off Delay, and Low-Current Ground or +12V Keying Phil Salas AD5X Introduction As a CW operator, I enjoy QSK operation with my ALS-600 amplifier (see the
More informationPacific Antenna Field Strength Indicator Kit
Pacific Antenna Field Strength Indicator Kit Description The Field Strength Indicator kit from Pacific Antenna provides a visual way to monitor the presence and relative strength RF fields through the
More informationPacific Antenna Easy TR Switch
Pacific Antenna Easy TR Switch Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate receiver
More informationConstruction Manual 6m-Linear-Transverter XV6/10
Construction Manual 6m-Linear-Transverter XV6/10 Holger Eckardt DF2FQ Kirchstockacherstr. 33 D-85662 Hohenbrunn 2606 Technical data exciter frequency: 28... 30 MHz RF frequency: 50... 52 MHz supply voltage:
More informationDemo Board LMH7220 High Speed LVDS Comparator
Demo Board LMH7220 High Speed LVDS Comparator General Description This board is designed to demonstrate the LMH7220 high speed comparator with LVDS output. The board consists of two parts; one part acts
More informationMAINTENANCE MANUAL RF BOARD 19D901835G1 ( MHz) 19D901835G2 ( MHz) FOR MVS
D MAINTENANCE MANUAL F BOAD 19D901835G1 (136-153 MHz) 19D901835G2 (150-174 MHz) FO MVS TABLE OF CONTENTS DESCIPTION............................................... Front Cover CICUIT ANALYSIS..............................................
More informationQRPme.com Kits. Tx/Tuna Topper. Assembly and Operation Guide. Kits for the QRP and Electronics Hobbyist. Heatsink left off for better assembly viewing
QRPme.com Kits Kits for the QRP and Electronics Hobbyist Tx/Tuna Topper Heatsink left off for better assembly viewing Contents Figures and Illustrations............................... 3 Jumpers............................................
More informationDEM Part Number L144-28INTCK 144 MHz Transverter Kit and complete kit
DEM Part Number L144-28INTCK 144 MHz Transverter Kit and complete kit Power Out: Noise Figure and Gain: DC Power Requirement: 50 mw linear minimum 3.5 db NF nominal, 5 dbg maximum 12-15.5 VDC, 13.8 nominal
More informationUHF/450MHz Band 100W Power Amplifier
Instruction Manual UHF/450MHz Band 100W Power Amplifier Model PA-100U-5 TOPTEK FEATURES PA-100U-5 is 2-stage UHF power amplifier, capable of delivering 100Watt RF output from less then 2Watt of drive power.
More informationModel 1791 VHF Radio User's Manual
Model 79 VHF Radio User's Manual ALL WEATHER INC 65 NATIONAL DRIVE SACRAMENTO, CA 95834 WWW.ALWEATHERINC.COM 79 VHF RADIO USER'S MANUAL CONTENTS INTRODUCTION... Description... Transmitter Module... Power
More informationEfficiency: 68% Temperature Range: +0 to 60 C Max VSWR: 5:1. Class: Supply Voltage:
Part Number Revision 2.C Release Date July 11 2007 Revision Notes - updated new format Amplifier Name Technical Specifications Summary Frequency Range: P1dB: Class: Supply Voltage: 88-108 MHz 750 Watts
More informationQRPme.com Kits. Tx/Tuna Topper. Assembly and Operation Guide. Kits for the QRP and Electronics Hobbyist. Heatsink left off for better assembly viewing
QRPme.com Kits Kits for the QRP and Electronics Hobbyist Tx/Tuna Topper Heatsink left off for better assembly viewing QRMme.com Kits Tx/Tuna Topper Contents Figures and Illustrations...............................
More informationM2 Antenna Systems, Inc. Model No: S3 Sequencer. Operating Instructions
WARRANTY ADDENDUM TROUBLESHOOTING INSTALLATION OVERVIEW M2 Antenna Systems, Inc. Model No: S3 Sequencer Operating Instructions PLEASE READ BEFORE USE AND SAVE M2 Antenna Systems, Inc. 4402 N. Selland Ave.
More informationUM User manual for the BGU7004 GPS LNA evaluation board. Document information. Keywords LNA, GPS, BGU7004. Abstract
User manual for the BGU7004 GPS LNA evaluation board Rev. 1.0 14 June 2011 User manual Document information Info Keywords Abstract Content LNA, GPS, BGU7004 This document explains the BGU7004 AEC-Q100
More informationS-Pixie QRP Kit. Student Manual. Revision V 1-0
S-Pixie QRP Kit Student Manual Revision V 1-0 Introduction The Pixie 2 is a small, versatile radio transceiver that is very popular with QRP (low power) amateur radio operators the world over. It reflects
More informationFrequency 434=434MHz 868=868MHz 915=915MHz
Ultra Low Power sub GHz Multichannels Transceiver The module is based on Texas Instruments CC0F component. This device combines a flexible, very low power RF transceiver with a powerful MHz Cortex M microcontroller
More informationCON NEX HP. OWNER'S MANUAL Full Channel AM/FM Amateur Mobile Transceiver TABLE OF CONTENTS TUNING THE ANTENNA FOR OPTIMUM S.W.R..
TABLE OF CONTENTS PAGE SPECIFICATIONS... 2 INSTALLATION... 3 LOCATION... 3 CON NEX - 4300HP MOUNTING THE RADIO... 3 IGNITION NOISE INTERFERENCE... 4 ANTENNA... 4 TUNING THE ANTENNA FOR OPTIMUM S.W.R..
More informationQRPGuys Michigan Mighty Might Plus 40M Transmitter
QRPGuys Michigan Mighty Might Plus 40M Transmitter First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use
More informationConverting the Motorola 42 to 50 MHz MT1000 or P200 to 50 to 54 MHz
Converting the Motorola 42 to 50 MHz MT1000 or P200 to 50 to 54 MHz Hardware mods by WB8VLC. RSS mods by WA1MIK Transmitter and receiver mods to tune the entire band and direct RSS frequency entry. Revision
More informationJUMA-TRX2 DDS / Control Board description OH2NLT
JUMA-TRX2 DDS / Control Board description OH2NLT 22.08.2007 General Key functions of the JUMA-TRX2 DDS / Control board are: - provide user interface functions with LCD display, buttons, potentiometers
More information1208 P10-VHF-H-20. Frequency Range: MHz. Efficiency: 10% Temperature Range: 0 to 70 C Max VSWR: 5:1. Class: Supply Voltage: 28.
Part Number Revision 2.C Release Date July 24, 2007 Revision Notes Included Mechanical Drawings Amplifier Name Technical Specifications Summary Frequency Range: 170-230 MHz P1dB: 10 Watts CW Class: A Supply
More informationINSTALLATION AND OPERATING MANUAL
INSTALLATION AND OPERATING MANUAL FOR RBDA-PCS-1/25W-90-A INDOOR REPEATER TABLE OF CONTENTS PARAGRAPH PAGE NO BDA OVERVIEW 3 BDA BLOCK DIAGRAM DESCRIPTION 3 FCC INFORMATION FOR USER 3 BDA BLOCK DIAGRAM
More informationDX 33HP. 10 Meter Amateur Mobile Transceiver OWNER S MANUAL. Download this Manual Free of Charge at
DX 33HP SIG 1 3 TX PWR 5 7 9+30dB POWER HI NB/ANL MED LO HI LO BAND ECHO RX/TX VOL SQ MIC RF FM PA AM D/A E/B F/C ECHO TIME BAND 10 Meter Amateur Mobile Transceiver Download this Manual Free of Charge
More informationCPDC2X1. 2X1 GPS Combiner Technical Product Data
CPDC2X1 2X1 GPS Combiner Technical Product Data Features Excellent Flatness Extremely Flat Group Delay Less that 1ns variation Low Insertion Loss Passes all GNSS Frequencies (Entire L-band) Provides Antenna
More informationMASTR II AUXILIARY RECEIVER 19D417546G7 & G8 & ANTENNA MATCHING UNITS 19C321150G1-G2. Maintenance Manual LBI-30766L. Mobile Communications
L Mobile Communications MASTR II AUXILIARY RECEIVER 19D417546G7 & G8 & ANTENNA MATCHING UNITS 19C321150G1-G2 Printed in U.S.A Maintenance Manual TABLE OF CONTENTS Page SPECIFICATIONS.....................................................
More informationMAINTENANCE MANUAL UHF REAR COVER ASSEMBLY 19C337097G4 - G7, G11, G13
LBI-38383D SCHEMATIC DIAGRAM MAINTENANCE MANUAL UHF REAR COVER ASSEMBLY 19C337097G4 - G7, G11, G13 TABLE OF CONTENTS Page DESCRIPTION........................................... Front Cover CIRCUIT ANALYSIS........................................
More informationConstruction Manual 4m-Linear-Transverter XV4-15
Construction Manual 4m-Linear-Transverter XV4-15 Holger Eckardt DF2FQ Kirchstockacherstr. 33 D-85662 Hohenbrunn 3207 Technical data exciter frequency: 21.0... 21.5 MHz RF frequency: 70.0.. 70.5 MHz supply
More informationOM1006 Solid State 50 MHz Power Amplifier
Instruction Manual OM1006 Solid State 50 MHz Power Amplifier OM POWER, s. r. o. 930 30 Báč 126 SLOVAKIA E-mail: om-power@om-power.com TABLE OF CONTENTS 1. GENERAL INFORMATION 1.1. Introduction.. 4 1.2.
More informationDX Connection. QSK 2500 Instruction Manual. 1) Description. 2) Specifications.
DX Connection QSK 2500 Instruction Manual 1) Description The DX Connection QSK 2500 allows operating a non-qsk amplifier in QSK mode (or SSB mode) with no amplifier modifications. No amplifier T/R relay
More informationKN-Q10 Assembly Manual
KN-Q10 Assembly Manual Translated by Adam Rong, BD6CR/4 with permission from Ke Shi, BA6BF Edited by Stephen, VK2RH Revision B, Oct 14, 2010 Thank you for purchasing the KN-Q10 4 Band SSB/CW Dual Mode
More informationVHF/AM SINGLE CHANNEL TRANSCEIVER Model TiL-92-SC (TSC-4100/4200/4300)
VHF/AM SINGLE CHANNEL TRANSCEIVER Model TiL-92-SC (TSC-4100/4200/4300) 25 WATT TRANSCEIVER P/N 921018-1 (TSC-4100) 15 WATT TRANSCEIVER P/N 921018-2 (TSC-4200) LOW POWER TRANSCEIVER P/N 921018-3 (TSC-4300)
More informationProgrammable Active Crystal Filters Catalog
Programmable Active Crystal Filters Catalog www.fiplex.com AERONAUTICAL BAND PROGRAMMABLE ACTIVE CRYSTAL FILTER* 118-137 MHz ACFA1-25 Crystal filter based filtering system, 25 KHz BW Software programmable
More informationReceiver Adjustments
! -8-4!5 This Section details procedures for tuning and adjustment of T2000 series II radios. This is normally only required during product manufacture or after major servicing. The following topics are
More informationDX 33HML. Full Channel AM/FM Mobile Transceiver OWNER S MANUAL. Printed In Malaysia AT H PD000802
DX 33HML Full Channel AM/FM Mobile Transceiver Printed In Malaysia AT3601014H PD000802 OWNER S MANUAL TABLE OF CONTENTS Page Specification.................................... 2 Installation Location.....................................
More informationSSRP LTC1746 Assembly Manual V0.1 Check the most recent version
SSRP LTC1746 Assembly Manual V0.1 Check the most recent version http://oscar.dcarr.org/ssrp/hardware/ltc1746/ltc1746.php Introduction This manual details the general assembly process for the SSRP LTC1746
More information150W1000B. Features. 150 watts CW 80MHz 1000MHz Class A Portable Full VSWR tolerant CE & RoHS Compliant High Efficiency
Power (Watts) Specifications Class A Portable Full VSWR tolerant CE & RoHS Compliant High Efficiency Features The Model is a solid-state, selfcontained, air-cooled, broadband amplifier designed for applications
More informationLoopBack Relay. LB363 Series. With Built-in AC Bypass Capacitors. LoopBack Relay, Sensitive Coil, thru-hole with AC Bypass Capacitors
LB363 Series With Built-in AC Bypass Capacitors SERIES DESIGNATION LB363 RELAY TYPE, Sensitive Coil, thru-hole with AC Bypass Capacitors DESCRIPTION The LoopBack Series relay combines two DPDT electromechanical
More informationRoHS Compliant 1310 nm Multi-mode Transceiver 2 5, LC Duplex Connector, 3.3 V 155 Mbps ATM/SONET OC-3/SDH STM-1/Fast Ethernet
Features Low power consumption Industry standard 2 5 footprint LC duplex connector Single power supply 3.3 V Differential LVPECL inputs and outputs Class 1 laser product complies with EN 60825-1 Ordering
More informationMirage B-310-G FEATURES
Mirage B-310-G Mirage B-310-G Instruction Manual The Mirage B-310-G is a VHF power amplifier designed for the 144-148 MHz band. New features make it the most useful and versatile amplifier available for
More informationLED Field Strength Indicator Kit
LED Field Strength Indicator Kit Description The Field Strength Indicator kit from Qrpkits.com provides a visual way to monitor RF fields through the brightness of an LED. It will respond to RF fields
More informationGAUSS High Power UHF Radio
[] Table of contents Table of contents... 1 1. Introduction... 3 Features... 4 Block Diagram... 6 2. Pinouts... 7 3. Absolute Maximum Ratings... 9 4. General Recommended Operating Conditions... 10 5. RF
More informationPA FAN PLATE ASSEMBLY 188D6127G1 SYMBOL PART NO. DESCRIPTION. 4 SBS /10 Spring nut. 5 19A702339P510 Screw, thread forming, flat head.
MAINTENANCE MANUAL 851-870 MHz, 110 WATT POWER AMPLIFIER 19D902797G5 TABLE OF CONTENTS Page DESCRIPTION.............................................. Front Page SPECIFICATIONS.................................................
More informationBoard Of Education, Revision C (28150)
599 Menlo Drive, Suite 00 Rocklin, California 95765, USA Office: (96) 624-8333 Fax: (96) 624-8003 General: info@parallax.com Technical: support@parallax.com Web Site: www.parallax.com Board Of Education,
More informationOcean Controls KT-5221 Modbus IO Module
Ocean Controls Modbus IO Module 8 Relay Outputs 4 Opto-Isolated Inputs 2 Analog Inputs (10 bit) 1 PWM Output (10 bit) 4 Input Counters Connections via Pluggable Screw Terminals 0-5V or 0-20mA Analog Inputs,
More informationAlcatel White Box 24GHz Transceiver experiments and modifications
Alcatel White Box 24GHz Transceiver experiments and modifications A set of working notes, measurements and comments PSU Need to supply : -5V up to ~ 30mA for Rx and PA modules +5.2V 1A for Rx and Tx mixer
More informationOptiva OTS-2 18 GHz Amplified Microwave Band Fiber Optic Links
MHz to 18 GHz Amplified Microwave Transport System The Optiva OTS-2 18 GHz Microwave Band transmitter and receiver are ideal to construct transparent fiber optic links in the MHz to 18 GHz frequency range
More informationNEW DESIGN***DEM Part Number FRS***NEW DESIGN Low power 144 MHz Transverter for the Flex Radio System SDR-1000 Operating Specifications:
NEW DESIGN***DEM Part Number 144-28FRS***NEW DESIGN Low power 144 MHz Transverter for the Flex Radio System SDR-1000 Operating Specifications: Operating Voltage: 12.0-15.5 VDC, 13.8 nominal Current Drain:
More informationFeatures 100A400AM20. 4kHz 400MHz Class A Portable Full VSWR tolerant CE & RoHS compliant High Efficiency
Specifications Class A Portable Full VSWR tolerant CE & RoHS compliant High Efficiency Features The Model is a solid-state, self -contained, air-cooled, broadband amplifier designed for applications requiring
More informationRockwell Collins, Inc. VHF Users Manual
Rockwell Collins, Inc. VHF-2200 Users Manual This manual provided to the FCC for product guidance, it should not be used by our OEM customers. Scope: This document will detail information required to install
More informationRF BOARD 19D902282G1, G3, G6, G8, G10, G13 & G17. (19D902269, Sh. 2, Rev. 17)
LBI-38383G SCHEMATIC DIAGRAM MAINTENANCE MANUAL UHF REAR COVER ASSEMBLY 19C337097G4 - G7, G11, G13, G17 TABLE OF CONTENTS Page DESCRIPTION........................................... Front Cover CIRCUIT
More informationDX Connection. QSK 2500 Instruction Manual. 1) Description. 2) Specifications.
DX Connection QSK 2500 Instruction Manual 1) Description The DX Connection QSK 2500 allows operating a non-qsk amplifier in QSK mode (or SSB VOX mode) with no amplifier modifications. No amplifier T/R
More informationPR-12-B-M. 12 GHz PhotoReceiver, Module. Features. Applications. Functional Diagram
PR-12-B-M 12 GHz PhotoReceiver, Module The Optilab PR-12-B-M is a 12 GHz bandwidth amplified PIN photodiode receiver module, designed for RF over fiber, antenna remoting, and broadband RF signals transmission
More information***note: pallet may draw up to 5.0 amps on a 32V supply.
Model BCI-UHF-40TX12 TV Pallet Amplifier Module This amplifier module is ideal for final output stages in analog and digital TV broadcast equipment. 470 860MHz 28-32 Volts Pout: 25W Peak Sync. 10Watts
More informationG3P-R232. User Manual. Release. 2.06
G3P-R232 User Manual Release. 2.06 1 INDEX 1. RELEASE HISTORY... 3 1.1. Release 1.01... 3 1.2. Release 2.01... 3 1.3. Release 2.02... 3 1.4. Release 2.03... 3 1.5. Release 2.04... 3 1.6. Release 2.05...
More informationLoopBack Relay. GLB363 Series. With Built-in AC Bypass Capacitors / DC LoopBack Relay
GLB363 Series With Built-in AC Bypass Capacitors / DC SERIES DESIGNATION GLB363 RELAY TYPE, Sensitive Coil, Surface Mount Ground Shield and Stub pins with AC Bypass Capacitors or No capacitor DESCRIPTION
More informationSMARTALPHA RF TRANSCEIVER
SMARTALPHA RF TRANSCEIVER Intelligent RF Modem Module RF Data Rates to 19200bps Up to 300 metres Range Programmable to 433, 868, or 915MHz Selectable Narrowband RF Channels Crystal Controlled RF Design
More informationHMC346MS8G / 346MS8GE
Typical Applications v7.18 Features This attenuator is ideal for use as a VVA for DC - 8 GHz applications: Point-to-Point Radio VSAT Radio Functional Diagram Wide Bandwidth: DC - 8 GHz Low Phase Shift
More informationProduct Specification PE42850
Product Description The PE4850 is a HaRP technology-enhanced SP5T high power RF switch supporting wireless applications up to GHz. It offers maximum power handling of 4.5 m continuous wave (CW). It delivers
More informationHMC310MS8G / 310MS8GE. Features OBSOLETE. = +25 C, Vdd = +3V
Typical Applications Transmit & Receive Switch for 2. GHz Applications: Bluetooth HomeRF WLAN Radios Functional Diagram v3.67 Electrical Specifications, T A = +25 C, Vdd = +3V HMC31MSG / 31MSGE Features
More informationFrequency Range: MHz. Efficiency: 10% Temperature Range: 0 to 60 C Max VSWR: 5:1. Class: Supply Voltage: 28.0V
Part Number Revision 1.c Release Date July 24, 2007 Revision Notes Amplifier Name Technical Specifications Summary Frequency Range: 50-88 MHz P1dB: 60 Watts CW Class: A Supply Voltage: 28.0V Gain: 36dB
More informationIntelPage 5W (POCSAG) Transmitter
A division of NESS CORPORATION PTY LTD IntelPage 5W (POCSAG) Transmitter INSTALLATION MANUAL IntelPage 5W (POCSAG) Transmitter Installation Manual v1.2 1. Contents 1. Contents... 1 2. Equipment List...
More informationDEM Part Number K, CK and LPK and CK 5.7 GHz. Transverter, Low Power Transverter, Kit and Complete Kit
DEM Part Number 5760-144K, CK and 5760-144LPK and CK 5.7 GHz. Transverter, Low Power Transverter, Kit and Complete Kit Specifications Frequency: 5760.000 = 144.000 standard Noise Figure and Gain < 1.5
More informationDC Injector (Bias Tee) kit. Technical Manual
DC Injector (Bias Tee) kit Technical Manual Document Author Dave Powis, G4HUP Date 7 Jan 2017 Version Issue 2_0 Document Ref HUP-05-020 http://huprf.com Tel +44 (0)1473 737717 g4hup@outlook.com Contents
More informationDiversity Antenna Distribution Module DADM226. Instruction manual
Diversity Antenna Distribution Module DADM226 Instruction manual Contents Contents... 2 Diversity Antenna Distribution Module (DADM 226)... 3 Operating Elements... 4 Setting up Procedure... 5 Setting up
More information2W UHF MHz Radio Transceiver
2W UHF410-470 MHz Radio Transceiver Specification Copyright Javad Navigation Systems, Inc. February, 2006 All contents in this document are copyrighted by JNS. All rights reserved. The information contained
More informationBGU8309 GNSS LNA evaluation board
BGU8309 GNSS LNA evaluation board Rev. 2 12 August 2016 Application note Document information Info Content Keywords BGU8309, GNSS, LNA Abstract This document explains the BGU8309 GNSS LNA evaluation board
More informationC99-20LL System Cable P/N 40935G-06 INSTALLATION SHEET
C99-20LL System Cable P/N 40935G-06 INSTALLATION SHEET The C99-20LL Interface cable connects a Universal Gateway Wireless System with the David Clark Series 9500 Marine Intercom System, and allows the
More informationREMARKS The customer has ordered two measurements mentioned above according to the standard EN
Type: Alignment range: Switching range: SATELLINE-3ASm/250/LC 380,000-470,000 MHz One channel Equipment 1 and 2 Equipment Equipment Measurement Serial no. 033322036 and 033322037 Serial no. Serial no.
More informationREIMESCH KOMMUNIKATIONSSYSTEME GMBH ALPIN HF / 50MHz Linear Amplifier - USER MANUAL. v1.1
REIMESCH KOMMUNIKATIONSSYSTEME GMBH ALPIN 100 - HF / 50MHz Linear Amplifier - USER MANUAL v1.1 DECLARATION OF CONFORMITY I hereby declare that the product: ALPIN 100, HF/6m 1kW Linear Amplifier satisfies
More information