Link-5 VHF. User Guide ENGLISH. lowrance.com

Transcription

1 Link-5 VHF User Guide ENGLISH lowrance.com

2 Copyright 2012 Navico All rights reserved. Lowrance is a registered trademark of Navico No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Lowrance Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited. Lowrance Electronics may find it necessary to change or end our policies, regulations, and special offers at any time. We reserve the right to do so without notice. All features and specifications subject to change without notice. All screens in this manual are simulated. For free owner s manuals and the most current information on this product, its operation and accessories, visit our web site: Important safety information Please read carefully before installation and use. DANGER WARNING CAUTION CAUTION This is the safety alert symbol. It is used to alert you to potential personal injury hazards, Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

3 Section 1 - General Information Features Customizing your Lowrance VHF Radio How to Display and Navigate Menus How to Enter Alphanumeric Data LCD Symbols and Meanings Basic Operation and Key Functions...9 Section 2 - The Radio Menu (MENU) Radio Menu Options (Menu) Maintain Your Buddy List (BUDDY LIST) Add an Entry Edit an Entry Delete an Entry Local or Distance Sensitivity (LOCAL/DIST) Set DISTANT Sensitivity Set LOCAL Sensitivity Backlighting (BACKLIGHT) and Contrast (CONTRAST) Set the Backlighting Level Set the Contrast Level GPS Data and Time (GPS/DATA) Manually Enter Position and UTC Time (MANUAL) Local Time (TIME OFFSET) Time Format Options (TIME FORMAT) Time Display Options (TIME DISPLAY) Position Display Options (LL display) Course & Speed Display Options (COG/SOG) GPS Alert Options (ALERT) GPS Simulator (SIMULATOR) Reset to Factory Defaults (RESET) Section 3 - Radio Setup Menu (RADIO SETUP) Radio Setup Menu (RADIO SETUP) Channel (UIC) Channel Names (CH NAME) RING & BEEP Volume (RING VOLUME) and (KEY BEEP) Internal Speaker Connections (INT SPEAKER) Set the Priority Channel (WATCH MODE) Weather Alert (Wx ALERT) NMEA protocol (COM PORT) Lowrance - Link-5 Operation and Installation Instructions 3

4 Section 4 - DSC Setup Menu (DSC SETUP) DSC Setup - Menu Options Enter or View Your USER MMSI (USER MMSI) Enter your MMSI View your MMSI Maintain Your Groups (GROUP SETUP) Create a Group (GROUP SETUP) Edit Group Name Details Delete a Group Response to Individual Calls (INDIV REPLY) ATIS MMSI & ATIS Functionality Enter or Edit YOUR ATIS MMSI View your ATIS MMSI Enable ATIS Functionality (ATIS FUNC) DSC functionality options (DSC FUNC) Response Type to LL Polling Calls (LL REPLY) Automatic Channel switching (AUTO SWITCH) DSC Test Reply (TEST REPLY) Set the inactivity timer (TIMEOUT) Section 5 - Sending and Receiving DSC Calls What is DSC? Sending DSC calls Make a Routine Call (INDIVIDUAL) Retrying a Routine Call Acknowledgement of an Individual Incoming Call (INDIV) Recall the Most Recent Incoming Call (LAST CALL) Call a Group (GROUP) Call All Ships (ALL SHIPS) Call using the Call Log (CALL LOG) Call using the Distress Log (DISTR LOG) Call using the Sent Call Log (SENT CALL) Request the LL Position of a Buddy (LL REQUEST) Make a DSC test call (DSC TEST) Receiving DSC Calls Receiving an All Ships Call (ALL SHIPS) Receiving an Individual Call (INDIV) Receiving a Group Call (GROUP) Receiving a Geographic Call (GEOGRAPH) Receiving a Polled Position Call (POSITION) Lowrance - Link-5 Operation and Installation Instructions

5 Section 6 - Distress Calls Sending a Distress Call Receiving a Distress Call (DISTRESS!) Distress Acknowledgement (DISTRESS ACK) Distress Relay Individual (INDIV DISTR RELAY) Section 7 - Installation...45 Installation Options Location Requirements Checklist Gimbal Installation Change the Viewing Angle Recessed Installation Install the Microphone Bulkhead Mount Fix the DSC label Connect the Radio Cables Set Up the Radio Enter Your User MMSI The Completed Installation Appendix A - Technical Specifications...52 Appendix B - Troubleshooting...54 Appendix C - US & ROW VHF Marine Channel Charts...55 C-1 International Channel Chart Special Notes on International Channel Usage...56 C-2 USA Channel Chart Special Notes on USA Channel Usage...58 C-3 CANADA Channel Chart Special Notes on Canada Channel Usage...60 C-4 US & Canada WEATHER Channels Appendix D - EU VHF Marine Channel Charts...62 D-1 EU International Channel Chart Special Notes on EU International Channel Usage...63 D-2 Inland Waterways Country Specific table - ATIS ON D-3 Special Channels Appendix E - MMSI, FCC and License Information...68 FCC Compliance...68 Lowrance - Link-5 Operation and Installation Instructions 5

6 Section 1 - General Information 1-1 Features Congratulations on your purchase of this Lowrance Link-5 marine band VHF radio. Your Link-5 provides the following useful features: Prominent channel display Adjustable contrast settings for the LCD Adjustable keypad backlighting for easy night-time use Waterproof and submersible to comply with JIS-7 GPS latitude and longitude (LL) and time display (when connected to a GPS) Choice of High or Low (25 W or 1 W) transmission power 6 key handset mic with built-in speaker Powerful 4 W external audio output Access to all currently-available marine VHF channel banks (USA, Canada, International) including weather channels where available (model dependant) Special CH16/9 key for quick access to the priority (international distress) channel Special 3CH key to select your three favourite channels Dedicated Wx (Weather) key PSCAN (similar to dual watch) facility DSC (Digital Select Calling) capability that meets Global DSC Class D Standards Separate CH70 receiver included built in DISTRESS call button to automatically transmit the MMSI and position until an acknowledgement is received Easy access to a buddy list of up to 20 favourite people MMSI storage for three favourite groups Group Call and All Ships Call facility LL position polling information Weather alert facility where available (US models) ATIS facility for inland waterways (EU models) With DSC Auto-Switch disable and DSC Test function 6 Lowrance - Link-5 Operation and Installation Instructions

7 1-2 Customizing your Lowrance VHF Radio You can customize the radio to suit your individual preferences. Some preferences can be set directly through the keys as explained in this Section. Other preferences are set up through the built-in menus and these are explained in the other Sections. You can check the software version of the radio and the User MMSI each time the radio is turned on, the screen will display the software version and the USER MMSI if one is programmed into the radio. 1-3 How to Display and Navigate Menus 1. Press MENU (or CALL). Note that only four menu items can be displayed at any one time on the screen. 2. Some line items may show an or indicator. This means there is more information available to show. Scroll (rotate the Rotary knob, or use + / - keys on the hand mic) to scroll up and down the menu until the cursor is positioned at the desired option. Press ENT (press the Push To Select) to display that option. 3. Make any entries or changes as explained in the following section. 4. Press ENT to confirm changes. Otherwise, press EXIT to keep the original entry. 5. Press EXIT to backup one screen (this key is equivalent to an ESC function on a PC). 1-4 How to Enter Alphanumeric Data If your radio does not have the optional alphanumeric microphone, you can Rotate the Rotary knob, or use + / - keys on the microphone key to enter alphanumeric data. Press - to count through numbers, or hold down to scroll rapidly to the desired number. Press + to step through the alphabet, or hold down to scroll rapidly to the desired character. If you make an error, press - until < is displayed, then press ENT to backup and correct the entry. 1-5 LCD Symbols and Meanings Link-5 LCD showing all segments: Typical Link-5 startup screen: LINK5 AUS/NZ VER:V1.999 DSC IS ON ID: Lowrance - Link-5 Operation and Installation Instructions 7

8 This simulation shows the locations of all the following information symbols: Symbol TX Meaning Transmitting. HI LO Transmission power. High (HI) 25W or Low (LO) 1W. WX WX ALT BUSY PRI D LOCAL DSC USA INT CAN X B A CH1 CH2 CH3 ATIS A typical display: Weather channel. Weather Alert. Alarm beeps will sound (US models only). Receiver busy with an incoming signal. Priority channel is selected. Duplex operation. Otherwise, blank for Simplex operation. Local calling is selected. Otherwise, blank for distance calling. DSC capability is available. Incoming DSC call. Low Battery warning (activates at 10.5 V). Channel selected. Selected channel bank for VHF radio operations and regulations. DSC Auto channel switch function is disabled (OFF) (see section 4-8) Channel suffix, if applicable. Shows which of the 3 favourite channels, if any, are selected. Otherwise blank. EU models only - must be enabled when in European inland waterways. The latitude and longitude of the vessel and the local time are shown. A transmission on Channel 16 is being made at high power The International channel bank is loaded. Channel 16 is set as the Priority channel. It is also set as favourite channel 1. DSC functionality is enabled. There is an incoming DSC call so the receiver is busy. 8 Lowrance - Link-5 Operation and Installation Instructions

9 1-6 Basic Operation and Key Functions All possible keys and their functions are listed here. Note that some of the keys may not be available depending on your Lowrance VHF radio model. 6 Key handset mic Link-5 base station radio Key: VOL/PWR SQL Function: Volume and Power. Turn clockwise to power on. Continue to turn until a comfortable volume is reached. VOL/PWR will also adjust the settings of an external speaker, if connected. Squelch or Threshold Level. Sets the threshold level for the minimum receiver signal. Turn fully counterclockwise until random noise is heard, then turn slowly clockwise until the random noise disappears. Make another 1/4 turn clockwise for best reception in open sea conditions. In areas of high noise (eg. close to large cities) reception may improve if sensitivity is reduced. Either turn SQL slowly clockwise or use the LOCAL setting. See section / 9 Priority Channel. Also on the handset mic. Press to cancel all other modes and to tune into the priority channel. Press again to return to your original channel. The default Priority Channel is CH16. DISTRESS PTT For US models: To make Channel 09 the priority channel, hold down 16/9 until a beep sounds and 09 is displayed. Send a DSC Distress Call. DSC must be active and an MMSI must be programmed. See Section 6. Press To Talk. (Located on the handset mic). Press PTT to transmit at any time on an allowable channel. This automatically exits you from menu mode and stops scanning. You must release PTT to receive a signal. If PTT sticks, a built-in timer will automatically shut down a transmission after five Lowrance - Link-5 Operation and Installation Instructions 9

10 PUSH TO SELECT ACCEPT OPT ACK EXIT QUIT CALL RESEND MENU WX INFO 3CH 10 minutes and sound a short error beep. Enter (ENT). Use ENT when navigating menus, to confirm entries and edits. Received DSC Call mode: Press to change immediately to the requested channel Received Individual Call mode: Press to view any incoming individual call reply options Send DISTRESS Call mode: Press to view and select any available options Receive Individual Call, LL Request, DSC Test Call, or Distress relay (US only) mode: Press to acknowledge an incoming call when an ACK is requested Escape (ESC). Use EXIT when navigating menus, to clear incorrect entries, to exit from a menu without saving changes, and to back up to the previous screen. DSC Call mode only: Press to return to the previous screen DSC Call Menu. Press to enter the DSC Call Menu and make DSC calls. See Section 6. DISTRESS CALL mode only: Press to resend a distress alert again Radio and DSC Setup Menu. Press to enter the DSC Setup Menu and to customize your radio. See Section 2-5. Weather Channel. For US models: In USA and Canadian waters, press to hear the most recently selected weather station. The WX symbol is displayed on the LCD. Rotate the dial or + / - on the handset mic to change to a different weather channel. Press WX again to return to the most recent channel. If the weather alert mode (ALT) is ON and an alert tone of 1050 Hz is broadcast from the weather station, it is picked up automatically and the alarm sounds. Press any key to hear the weather alert voice message. For all other models: The Wx key can be programmed to a weather channel of your choice. Select a channel you wish to use as your weather channel, then press and hold the Wx key for a few seconds. The radio will beep to confirm your choice. You now have quick access to your favourite channel by pressing the Wx key. DISTRESS CALL mode only: Press to review distress call information. Three Favourite Channels. Also on the handset mic. Press to toggle between your favourite channels. The CH1, CH2, or CH3 symbol appears on the LCD to show which favourite channel is selected. To scan only one of your favourite channels, press 3CH then immediately press and release SCAN. If you want to scan all three favourite channels, press 3CH then immediately press and hold SCAN. To add a favourite channel for the first time, select that channel then hold 3CH to store it in the CH1 location. Repeat the procedure to store two more favourite channels in the CH2 and CH3 locations respectively. If you try and add another favourite channel it will overwrite the existing CH3. CH1 Lowrance - Link-5 Operation and Installation Instructions

11 PAUSE SCAN and CH2 remain unless you delete them. To delete a favourite channel, select that channel then hold down 3CH until the CH1, CH2 or CH3 symbol disappears off the LCD. DISTRESS CALL mode only: Pause the automated distress alert resend countdown timer. Scan. Press to scan between your current channel and the priority channel in DUAL or TRI WATCH mode. The weather channel is also scanned if the USA channel bank is selected and the weather alert mode (ALT) is ON. Hold down SCAN to enter ALL SCAN mode where the priority channel is checked every 1.5 seconds. DISTR. CANCEL Rotary knob SILENCE When a signal is received, scanning stops at that channel and BUSY appears on the screen. If the signal ceases for more than 5 seconds, the scan restarts. Press ENT to temporarily skip over (lock out) an always busy channel when in ALL SCAN mode and resume the scan. If a channel is skipped, the word SKIP ON will momentarily replace the channel name shown on the LCD to designate a skipped channel. The channel name will then have * appended to the end of the channel name. Note that it is not possible to skip over the priority channel. To cancel a skipped channel, select the channel while in normal mode (non-scan mode) then press the ENT key - SKIP OFF will be displayed momentarily and the channel will be restored. Alternatively, you can re-power the radio. Press SCAN to stop at the current channel. Press EXIT to cancel scan mode and return to normal operation. DISTRESS CALL mode only: Press to send a distress cancel call. Channel Select. Turn to select a channel. The current channel is shown on the LCD in BIG digits and an A or B designator suffix (if applicable) in small letters below the channel number. See Appendix C for a complete listing of channel charts. Push to activate the ENT function. You can also use the rotary knob for alphanumeric entry. Turn to step through alphanumeric characters one at a time, then push to confirm each selection. If you make an error, select the < character then push to backup. DSC Call mode only: Rotate the rotary knob to silence the call alert when a DSC call is received. + / - Channel Select. (Located on the handset mic). The current channel is shown on the screen in BIG digits with an appropriate designator suffix A or B in small letters below the channel number. Press + or - to step through the available channels one at a time, or hold down to scroll rapidly through all the available channels. See Appendix C for a complete listing of channel charts. Lowrance - Link-5 Operation and Installation Instructions 11

12 H/L Alphanumeric Entry. This key can be used for both menu selection and for alphanumeric entry. Press + or - to scroll the cursor up or down to menu options when navigating menus. When editing an item containing only numbers, press - to count through the numbers or hold down to scroll rapidly. To enter a character, press + to step through the alphabet or hold down to scroll rapidly. Transmission Power. (Located on the handset mic). High (HI) 25 W or Low (LO) 1 W. Press to toggle between high or low transmission power for the entire channel bank. The HI or LO selection is shown on the LCD. Some channels allow only low power transmissions. Error beeps will sound if the power transmission setting is incorrect. Some channels allow only low power transmissions initially, but can be changed to high power by holding down H/L and PTT at the same time. See Appendix C for a complete listing of channel charts. INFO PAUSE RESEND ACCEPT/OPT/ACK/ENT QUIT DISTR CANCEL Close-up of the Link-5 base station radio, showing the keys 12 Lowrance - Link-5 Operation and Installation Instructions

13 Section 2 - The Radio Menu (MENU) 2-1 Radio Menu Options (Menu) The following options are available through the MENU key: BUDDY LIST LOCAL/DIST BACKLIGHT CONTRAST Maintain your buddy list. See Section 2-2. Set radio sensitivity. See Section 2-3. Set backlight level. See Section 2-4. Set contrast level. See Section 2-4. GPS/DATA DSC SETUP MANUAL SETTING USER MMSI GROUP SETUP ATIS MMSI * ATIS FUNC * INDIV REPLY DSC FUNC LL REPLY AUTO SWITCH TEST REPLY TIMEOUT Set position & UTC manually. See Section 2-5. Set local time and time format. See Section 2-5. DSC Setup Menu. See Section 4. Make DSC calls. See Section 5. RADIO SETUP GPS SIM RESET * Model dependant UIC * CH NAME RING VOLUME KEY BEEP INT SPEAKER WATCH MODE * WX ALERT * COM PORT Radio Setup Menu. See Section 3. Turn the GPS Simulator on/off. See Section 2-6. Reset factory settings. See Section 2-7. Sections 1-3 and 1-4 explain how to navigate around the menu and enter, save and change data. Lowrance - Link-5 Operation and Installation Instructions 13

14 2-2 Maintain Your Buddy List (BUDDY LIST) MENU SELECT BUDDY LIST LOCAL/DIST BACKLIGHT Use the Buddy List to store the names and associated MMSI s of 20 favourite people. Names are stored in the order of entry, with the most recent entry shown first. The following sections show how to add, edit, and delete entries on your BUDDY LIST. Section 5 explains how to call a buddy Add an Entry BUDDY LIST MANUAL NEW ALEX TOM ENTER NAME ENTER MMSI ENTER NAME BOB ENTER MMSI BOB STORE CANCEL 1. Select BUDDY LIST. The cursor is at MANUAL NEW. Press ENT. 2. Enter the buddy name, one character at a time (this may be alphanumeric) then press ENT repeatedly until the cursor moves to the MMSI entry line. 3. Enter the MMSI associated with that buddy name (this must be numeric) then press ENT. If the MMSI is for a Coast Station, enter the 7 digits then press ENT twice. 4. The new buddy name and MMSI are displayed. Press ENT to store the new entry, which is displayed at the top of your buddy list. Note: When the BUDDY LIST is full (20 entries), you can make a new entry and the buddy at the end of the list is automatically erased Edit an Entry BUDDY LIST MANUAL NEW ALEX TOM ALEX EDIT DELETE EDIT NAME ALEX EDIT MMSI ALEX STORE CANCEL 1. Select BUDDY LIST. Press ENT to display the list of entries. 2. Scroll down (if required) to the entry and press ENT. 3. Select EDIT. The cursor is at the first character of the name. 4. Edit the buddy name or, to edit only the MMSI, press ENT repeatedly until the cursor moves to the MMSI line. 5. When you are finished, press ENT (repeatedly if necessary) to display the next screen. 6. Press ENT to store the changes. The buddy list is displayed again. If more changes are required, repeat Steps 2 through 6. Otherwise, press EXIT to cancel. 14 Lowrance - Link-5 Operation and Installation Instructions

15 2-2-3 Delete an Entry BUDDY LIST MANUAL NEW ALEX TOM BUDDY LIST MANUAL NEW ALEX TOM TOM EDIT DELETE DELETE BUDDY TOM YES NO 1. Select BUDDY LIST. Press ENT to display the list of entries. 2. Scroll down (if required) to the entry you want to delete and press ENT. 3. Select DELETE then select YES. 4. The entry is deleted immediately and the buddy list is displayed again. 2-3 Local or Distance Sensitivity (LOCAL/DIST) MENU SELECT BUDDY LIST LOCAL/DIST BACKLIGHT See also SQL (Squelch Control) in Section Set DISTANT Sensitivity SENSITIVITY DISTANT LOCAL Use LOCAL/DIST to improve the sensitivity of the receiver either locally (LOCAL) or over distances (DIST). LOCAL is not recommended for use in open sea conditions. It is designed for use in areas of high radio noise; for example, close to cities. 1. Select LOCAL/DIST then select DIST. 2. Press ENT to activate the DIST setting. This disables local sensitivity and the menu is displayed again Set LOCAL Sensitivity SENSITIVITY DISTANT LOCAL 1. Select LOCAL/DIST then scroll to LOCAL. 2. Press ENT to activate the LOCAL setting. This disables distance sensitivity and the menu is displayed again. LOCAL is displayed on the LCD as a reminder that local sensitivity is selected. 2-4 Backlighting (BACKLIGHT) and Contrast (CONTRAST) MENU SELECT LOCAL/DIST BACKLIGHT CONTRAST Use BACKLIGHT to set the backlight levels for the LCD, keypad and microphone keypad to a comfortable level. Use CONTRAST to set the contrast level for the LCD. Lowrance - Link-5 Operation and Installation Instructions 15

16 2-4-1 Set the Backlighting Level BACKLIGHT LO HI PRESS ENT 1. Select BACKLIGHT. 2. Select a comfortable backlight level using + or - to change the setting. 3. Press ENT to enable the setting and return to the menu. Note: The DISTRESS key backlighting cannot be switched off Set the Contrast Level CONTRAST LO HI PRESS ENT 1. Select CONTRAST. 2-5 GPS Data and Time (GPS/DATA) MENU SELECT BACKLIGHT CONTRAST GPS/DATA 2. Select a comfortable contrast level using + or - to change the setting. 3. Press ENT to enable the setting and return to the menu. If the boat has an operational GPS navigation receiver, the VHF radio automatically detects and updates the vessel position and the local time. However, if the GPS navigation receiver is disconnected or absent, you can specify the vessel position and the local time manually, using the GPS/DATA option. This information is important because it will be used if a DSC distress call is transmitted. You can also select GPS Alert and GPS Simulator options Manually Enter Position and UTC Time (MANUAL) Note that this function is available only if an operational GPS receiver is not connected. GPS/DATA MANUAL SETTING MANUAL LL. 'N. 'E MAN : UTC PORT OPS 10:12AM UTC M 'N 'W 1. Select GPS/DATA, then MANUAL. 2. Enter the latitude, then the longitude, then the UTC. 3. Press ENT when all the information is correct. 16 The vessel s latitude and longitude are shown on the screen, with the UTC time. The prefix M indicates a manual entry. The manual entries are cancelled if a real GPS position is received. Lowrance - Link-5 Operation and Installation Instructions

17 2-5-2 Local Time (TIME OFFSET) The local time can be set by entering the time offset between UTC and local time as follows. GPS/DATA MANUAL SETTING SETTING TIME OFFSET TIME FORMAT TIME DISPL TIME OFFSET +01:30 02:30PM LOC 1. Select GPS/DATA, then SETTING. 2. Select TIME OFFSET to enter the difference between UTC and local time. 15 minute increments can be used with a maximum offset of ±13 hours. L M Y L M L In this example, a difference of +1.5 hours has been entered and the local time is displayed with the suffix LOC. X W V U T S R Q P O N Z A B C D E F G H I K L M Y Q S Z A G K N C T R Z V K S A B I L P G E Z H W U T Q C K R P* A B F E L D U S R Z B T Z H I I X C* D* E X R E B I W C D F R Q H Z E* A F* N G S C K C M E* M Q * H M R Z E H M* C G K V* S D Q O A B F I I K L I X C M W P G Z L A F* H M W O C L M * D W M* U S H I* Q B K L M * Z * P K M International Date Line M STANDARD TIME ZONES Corrected to January 2011 Zone boundaries are approximate Daylight Saving Time (Summer Time), usually one hour in advance of Standard Time, is kept in some places Map outline Mountain High Maps Compiled by HM Nautical Almanac Office W 120 W 90 W 60 W 30 W 0 30 E 60 E 90 E 120 E 150 E Time Format Options (TIME FORMAT) Time can be shown in 12 or 24 hour format. P Q O h m Z 0 A 1 B 2 C 3 C* 3 30 D 4 Standard Time = Universal Time value from table Universal Time = Standard Time + value from table h m h m h m h m h m h m D* 4 30 G 7 L 11 N + 1 Q* V + 9 E 5 H 8 L* O + 2 R + 5 V* E* 5 30 I 9 M 12 P + 3 S + 6 W +10 E 5 45 I* 9 30 M P* T + 7 X +11 F 6 K 10 M* 13 Q + 4 U + 8 Y +12 F* 6 30 K* M 14 No Standard Time legally adopted K M International Date Line M WORLD MAP OF TIME ZONES GPS/DATA MANUAL SETTING SETTING TIME OFFSET TIME FORMAT TIME DISPL TIME FORMAT 12 Hr 24 Hr 07:15AM LOC Lowrance - Link-5 Operation and Installation Instructions 17

18 1. Select GPS/DATA, then SETTING. 2. Select TIME FORMAT. 3. Select 12 Hr or 24 Hr as desired. In this example, 12 hour format has been selected and the LCD shows the AM or PM suffix Time Display Options (TIME DISPLAY) If you have entered the time manually as described in the previous sections, the time is always shown on the screen with the prefix M. However, if the vessel position is being updated through a GPS navigation receiver, you can switch the time display on the screen ON or OFF as follows: SETTING TIME OFFSET TIME FORMAT TIME DISPL Lowrance - Link-5 Operation and Installation Instructions 1. Select GPS/DATA, then SETTING. 2. Select TIME DISPLAY. 3. Select ON (on) or OFF (off ) as desired. In this example, OFF has been selected and the screen no longer shows the time. If the time display is set ON, course and speed data are not displayed on the LCD (see section 2-5-6) Position Display Options (LL display) If you have entered the vessel position manually as described in the previous section, the vessel position is always shown on the screen with the suffix M. However, if the time is being updated through a GPS navigation receiver, you can switch the vessel position display on the screen on or off as follows: SETTING TIME FORMA TIME DISPLY LL DISPLY Course & Speed Display Options (COG/SOG) 1. Select GPS/DATA, then SETTING. 2. Select LL DISPLAY. 3. Select ON (on) or OFF (off ) as desired. In this example, OFF has been selected and the screen no longer shows the vessel position. Use this option to display course over ground (COG) and speed over ground (SOG) data on the screen. SETTING TIME DISPL LL DISPLY COG/SOG TIME DISPLY ON OFF LL DISPLAY ON OFF COG/SOG ON OFF 1. Select GPS/DATA, then SETTING. 2. Select COG/SOG. 3. Select ON (on) or OFF (off ) as desired. In this example, ON has been selected and the screen shows the bearing and speed. If COG/SOG is set ON (on), the time is not displayed on the screen (see section 2-5-4).

19 2-5-7 GPS Alert Options (ALERT) The GPS alert is usually set to ON (on) so that if the GPS navigation receiver is disconnected, the alarm sounds. SETTING LL DISPLY COG/SOG GPS ALERT 2-6 GPS Simulator (SIMULATOR) 1. Select GPS/DATA, then SETTING. 2. Select GPS ALERT. 3. Select ON (on) or OFF (off ) as desired. The GPS Simulator is set to OFF whenever the radio is switched ON, or whenever real GPS data is available through the COM port. However, if you want to test it, turn it on. MENU SELECT DSC SETUP RADIO SETUP GPS SIM GPS ALERT ON OFF 1. Select GPS SIM, then select ON (on) or OFF (off ) as desired. Whenever the GPS Simulator is turned ON (on), simulated Speed Over Ground (SOG), Course Over Ground (COG), and LL position appear on the screen. This data is updated automatically during the simulation. Important: It is not possible to send a DSC transmission when in Simulator mode. 2-7 Reset to Factory Defaults (RESET) Use this setting to return every setting to the factory defaults except all MMSI settings, entries in your buddy list and any edited channel names. MENU SELECT RADIO SETU GPS SIM RESET RESET RADIO ARE YOU SURE YES NO 1. Select RESET. The radio asks for confirmation. 2. Select YES to reset the radio and return to the menu. Lowrance - Link-5 Operation and Installation Instructions 19

20 Section 3 - Radio Setup Menu (RADIO SETUP) 3-1 Radio Setup Menu (RADIO SETUP) The following options are available through MENU key: UIC * Channel band. See Section 3-2. CH NAME RING VOLUME KEY BEEP INT SPEAKER WATCH MODE * WX ALERT * COM PORT * Model dependant Sections 1-3 and 1-4 explain how to navigate around the menu and enter, save and change data. 3-2 Channel (UIC) Edit or delete channel names. See Section 3-3. Note: UIC may not be available on all models. Set the volume level of the incoming call notification beeps. See section 3-4. Set the volume level of the beeps. See section 3-4. Switch ON/OFF (on/off ) the radio s internal speakers. See section 3-5. Selects Priority Channel operation with Dual or Tri watch scanning. See section 3-6. Selects if the WX Alert scanning mode is ON (on) or OFF (off ). See section 3-7. Select NMEA protocol for communications between the VHF radio and any other instruments. See section 3-8. Toggle between USA, International or Canadian channel banks. The selected channel bank is displayed on the LCD along with the last used channel. All the channel charts are shown in Appendix C. RADIO SETUP UIC CH NAME RING VOLUM UIC USA INT L CANADA 20 Lowrance - Link-5 Operation and Installation Instructions

21 3-3 Channel Names (CH NAME) The channel charts are listed in Appendix C with their default name tags. CH NAME gives you the option to edit or delete the channel name tags displayed on the screen. RADIO SETUP CH NAME RING VOLUME KEY BEEP CH NAME TELEPHONE 01 TELEPHONE EDIT DELETE EDIT CH NAME TELEPHONE EDIT CH NAME PHONE1 YES NO 1. Select RADIO SETUP, then CH NAME. 2. Use + or - to step through the channels with their name tags until you see the channel name tag you want to change, then press ENT. In this example, the channel name TELEPHONE associated with channel 01 is being changed to PHONE1. 3. Select EDIT and press ENT to edit the existing name tag. Input the new name over the existing name. It can be a maximum of 12 characters. To delete the channel name, select DELETE and press ENT. 4. Press ENT (repeatedly if necessary) to display the YES/NO confirmation. 5. Press ENT to confirm the new channel name tag or the deletion, then press EXIT to return to the menu. 3-4 RING & BEEP Volume (RING VOLUME) and (KEY BEEP) Set the volume level of the incoming signal beeps (RING VOLUME) and/or the error and warning beeps (KEY BEEP) to HIGH (high) or LOW (low) as follows: RADIO SETUP CH NAME RING VOLUME KEY BEEP RING VOLUME HIGH LOW KEY BEEP HIGH LOW OFF 1. Select RADIO SETUP, then RING VOLUME or BEEP VOLUME as appropriate. 2. Select a HIGH or LOW volume. (It is possible to turn the beeps off completely by selecting KEY BEEP then OFF.) 3. Press ENT to enable the new volume setting and return to the menu. 3-5 Internal Speaker Connections (INT SPEAKER) Switch the radio s internal speaker ON (on) or OFF (off ). The external speaker is always ON (on) if a speaker is plugged into the external speaker jack. Lowrance - Link-5 Operation and Installation Instructions 21

22 RADIO SETUP RING VOLUM KEY BEEP INT SPEAKE 3-6 Set the Priority Channel (WATCH MODE) 1. Select RADIO SETUP, then INT SPEAKER. 2. Select ON (on) or OFF (off ) then press ENT to enable the setting and return to the menu. For EU models, watch mode is similar to a dual watch, scanning between the priority channel CH16 and the working channel. If you have US model and are operating on USA or Canadian channel banks, you can set the priority channel to cover both CH16 and CH09 as well as the working channel, as follows: RADIO SETUP KEY BEEP INT SPEAKER WATCH MODE 3-7 Weather Alert (Wx ALERT) US models ONLY 1. Select RADIO SETUP, then WATCH MODE. 2. Select ONLY 16CH for dual watch mode, or 16CH+9CH for tri watch mode. The NOAA provides several weather forecast channels on USA and Canadian channel banks. If severe weather such as storms or hurricanes are forecast, the NOAA broadcasts a weather alert on 1050 Hz. You can set up the radio to pick up weather alerts, as follows: RADIO SETUP INT SPEAKE WATCH MODE WX ALERT 1. Select RADIO SETUP, then WX ALERT. 2. Select ON (on) or OFF (off ) then press ENT to enable the setting and return to the menu. When a weather alert is broadcast, the alarm will sound. Press any key to hear the weather alert voice message. 3-8 NMEA protocol (COM PORT) This radio uses NMEA0183 protocol to receive GPS data from a compatible GPS unit. The COM Port must be configured correctly before use. The radio can be added to a group of instruments using NMEA protocol. RADIO SETUP WATCH MODE WX ALERT COM PORT INT SPEAKER ON OFF WATCH MODE ONLY 16CH 16CH+9CH WX ALERT ON OFF NMEA CHECKSUM ON OFF CHECKSUM ON is the default setting. 1. Select RADIO SETUP, then COM PORT. 2. Select CHECKSUM ON (on) or OFF (off ) then press ENT to enable the setting and return to the menu. The COM Port uses 4800 baud rate and can receive the following GPS data sentence: RMC, GGA, GLL, GNS. Additionally, this radio will output the following NMEA DSC data: DSC (for DSC call), DSE ( for enhanced position). 22 Lowrance - Link-5 Operation and Installation Instructions

23 Section 4 - DSC Setup Menu (DSC SETUP) 4-1 DSC Setup - Menu Options The following options are available through MENU key: Enter or view your user MMSI. See section 4-2. USER MMSI (If you do not have a user MMSI, see Appendix D.) Enter or change the name and/or details of a group. GROUP SETUP See section 4-3. Enter, change or view your ATIS MMSI. ATIS MMSI * See section 4-5. Enable/disable the ATIS function. ATIS FUNC * See section Choose an automatic or manual response to calls. INDIV REPLY See section 4-4. DSC FUNC Turn the DSC operation ON/OFF (on/off ). See section 4-6. LL REPLY Select the type of response to an LL polling request. See section 4-7. AUTO SWITCH Enable/disable automatic channel switching with DSC message See section 4-8. TEST REPLY Choose an automatic or manual response to DSC test call. See section 4-9. TIMEOUT Set the inactivity timer for Automated and Non-Automated items. See section * Model dependant 4-2 Enter or View Your USER MMSI (USER MMSI) You must enter your user MMSI before you can access the DSC functions. This is a once-only operation Enter your MMSI WARNING A valid USER MMSI must be entered into this radio before these DSC functions can be used. See below for instructions on how to Enter Your USER MMSI (USER MMSI). You can display and read your user MMSI at any time, but you get only one opportunity to enter your user MMSI. Contact Lowrance if you need to change your MMSI after initial input. DSC SETUP USER MMSI GROUP SETUP INDIV REPL INPUT USER MMSI USER MMSI STORE CANCEL USER MMSI INPUT AGAIN Lowrance - Link-5 Operation and Installation Instructions 23

24 1. Select DSC SETUP, then USER MMSI. 2. If this is the first time that you are entering your user MMSI, a dashed line appears. Enter your user MMSI along the dashed line using the rotary knob as described in Section 1-4. Press ENT to confirm each correct entry and to move to the next digit. If you make an error, press - until < appears, then press ENT to backup and correct the entry. 3. Press ENT to store your user MMSI. 4. You may need to enter your user MMSI again as a password check, then press ENT to permanently store the user MMSI and return to the menu View your MMSI You can view your stored user MMSI at anytime by selecting MMSI/GPS in the CALL menu. WARNING NO MMSI DSC DISABLED ENT>>SILENCE Alternatively, the user MMSI is displayed each time the radio is turned on. If a user MMSI is not programmed into the radio, the radio will display a warning and sound an audible alarm at startup warning you that all DSC functions are disabled (model dependant). 4-3 Maintain Your Groups (GROUP SETUP) Use GROUP SETUP to create, edit, or delete 1, 2, or 3 groups of frequently called people stored in alphanumeric order. A group MMSI always starts with Create a Group (GROUP SETUP) DSC SETUP USER MMSI GROUP SETUP INDIV REPL GROUP SETUP MANUAL NEW GROUP NAME GROUP MMSI 0 FISHER STORE CANCEL 1. Select DSC SETUP, then GROUP SETUP. 2. If this is the first time that you are entering a group name, a line of nine zeros appears. Otherwise, any existing group names are displayed. Press ENT to display the input screen. 3. Enter the group name along the dashed line. It can be alphanumeric. Press ENT to confirm each correct entry and to move to the next digit. When you have finished, press ENT repeatedly until the cursor moves to the MMSI line. If you make an error, press - until < appears, then press ENT to backup and correct the entry. 4. Enter the group MMSI. Note that the first number is always 0. Press ENT. 5. The group name and group MMSI are shown in a confirmation screen. Press ENT to store the details and return to the GROUP SETUP screen. 24 Lowrance - Link-5 Operation and Installation Instructions

25 4-3-2 Edit Group Name Details GROUP SETUP MANUAL NEW FISHER1 FRIENDS1 FISHER1 EDIT DELETE EDIT NAME FISHER1 EDIT MMSI FISHER STORE CANCEL 1. Select DSC SETUP, then GROUP SETUP. The existing group names are displayed. Press + or - to scroll to the incorrect entry then press ENT. 2. Press ENT to edit. The group name details are displayed, with the cursor at the first character of the name. 3. Edit the buddy name or, to edit only the MMSI, press ENT repeatedly until the cursor moves to the MMSI line. 4. When you are finished, press ENT (repeatedly if necessary) to display the next screen. 5. Press ENT to store the changes and return to the GROUP SETUP screen Delete a Group GROUP SETUP MANUAL NEW FISHER2 FRIENDS1 FISHER2 EDIT DELETE DELETE GROUP FISHER2 YES NO 1. Select DSC SETUP, then GROUP SETUP. The existing group names are displayed. 2. Press + or - to scroll to the incorrect entry then press ENT. 3. Select DELETE and press ENT. The radio asks for confirmation. 4. Press ENT to delete the group and return to the GROUP SETUP screen. 4-4 Response to Individual Calls (INDIV REPLY) You can respond to incoming individual calls with an automatic response or with a manual response. Note - this does not apply for Routine Calls. An AUTOmatic response sends an acknowledgement and then sets the request link channel, ready for a conversation after 10 seconds of receiving the call. USA default. A manual response asks if you want to acknowledge the call, and then asks if you want to converse with the caller. This is the default setting for EU models. DSC SETUP USER MMSI GROUP SETUP INDIV REPL INDIV REPLY MANUAL AUTO 3. Press ENT to confirm your choice and return to the menu. 1. Select DSC SETUP, then INDIV REPLY. 2. Select AUTO for an automatic response, or MANUAL for a manual response. Lowrance - Link-5 Operation and Installation Instructions 25

26 4-5 ATIS MMSI & ATIS Functionality EU models ONLY ATIS is only available in certain EU models. You must enter your ATIS MMSI to access ATIS functionality. ATSI must be used if you are navigating inland waterways within Europe. An ATIS MMSI is different to your DSC MMSI. ATIS sends a digital message each time that you release the PTT key. Inland waterways rules require 1 W Tx power on Channels 06, 08, 10, 11, 12, 13, 14, 15, 17, 71, 72, 74 and Enter or Edit YOUR ATIS MMSI DSC SETUP GROUP SETU INDIV REPLY ATIS MMSI INPUT ATIS MMSI INPUT ATIS MMSI STORE CANCEL INPUT AGAIN ATIS MMSI ATIS MMSI STORE CANCEL Note: An ATIS MMSI always starts with the number To enter or edit your ATIS MMSI: 2. Select DSC SETUP, then ATIS MMSI. 3. If this is the first time that you are entering your ATIS MMSI, a dashed line appears. Enter your ATIS MMSI along the dashed line using the rotary knob as described in Section 1-4. The first number is always 9. Press ENT to confirm each correct entry and to move to the next digit. If you make an error, press - until < appears, then press ENT to backup and correct the entry. If you are editing an existing ATIS MMSI, this will be displayed. Make the required changes. 4. Press ENT to store your user ATIS MMSI. 5. You may need to enter your ATIS MMSI again as a password check, then press ENT to permanently store the ATIS MMSI and return to the menu View your ATIS MMSI You can view your stored ATIS MMSI at anytime by selecting ATIS MMSI in the main menu, DSC SETUP. 26 Lowrance - Link-5 Operation and Installation Instructions

27 4-5-3 Enable ATIS Functionality (ATIS FUNC) ATIS functionality can only be activated if an ATIS MMSI has been entered. See DSC SETUP INDIV REPL ATIS MMSI ATIS FUNC ATIS FUNC ON OFF DSC IS ON 1. Select DSC SETUP, then ATIS FUNC. ATIS Note: It is not possible to have both ATIS ON (on) and DSC ON (on) simultaneously. If you want to activate ATIS, you must first switch DSC off. A note on the LCD will remind you if DSC is already ON. 2. Select ON to enable the ATIS functionality - DSC must be turned off first. The ATIS annunciator appears on the screen. 4-6 DSC functionality options (DSC FUNC) DSC functionality can be disabled but this is not recommended unless you are going to turn ATIS on. DSC SETUP GROUP SETU. INDIV REPLY DSC FUNC DSC FUNC ON OFF ATIS IS ON 1. Select DSC SETUP, then DSC FUNC. Note: It is not possible to have both ATIS ON (on) and DSC ON (on) simultaneously. If you want to activate DSC, you must first switch ATIS off. A note on the LCD will remind you if ATIS is already ON. 2. Select ON to enable the DSC functionality - ATIS (if applicable) must be turned off first. The DSC annunciator appears on the screen. There are two annunciators on the screen to show you the current mode: if the DSC annunciator is shown, DSC is operational, if the ATIS annunciator is shown, ATIS is operational. 4-7 Response Type to LL Polling Calls (LL REPLY) You can set the radio to respond to an LL polling request in one of three ways: AUTO MANUAL OFF automatically replies to any incoming LL polling requests from any of your buddies. choose to manually reply to any incoming buddy polling requests. ignores all incoming buddy LL polling requests. Lowrance - Link-5 Operation and Installation Instructions 27

28 DSC SETUP INDIV REPL DSC FUNC LL REPLY LL REPLY MANUAL AUTO OFF 1. Select DSC SETUP, then LL REPLY. 2. Select your response and press ENT to confirm and return to the menu. 4-8 Automatic Channel switching (AUTO SWITCH) When a DSC call is received, it may include a request to change to a specific channel for subsequent communications. If a channel switch request is included, your options are: allow the radio to switch to the requested channel immediately by pressing the ENT button, or do nothing to allow the radio to automatically switch to the requested channel after a delay of 10 seconds, or cancel the automatic switch and remain on the current channel by pressing the EXIT button. However, automatic switching to a subsequent communications channel on receipt of a DSC call might in some cases disrupt important ongoing communications if the working channel changes without the operator knowing. You can prevent the radio from automatically switching from the current working channel by setting the AUTO SWITCH feature to OFF. If the AUTO SWITCH feature is set to OFF, an X will be displayed on the LCD to remind you that this feature is set to off. Additionally, the text AUTO SW OFF will be included in an All Ships or Group call replacing the text AUTO CHxx DSC SETUP DSC FUNC LL REPLY AUTO SWITC AUTO SWITCH ON OFF 1. Select DSC SETUP, then AUTO SWITCH. 2. Select ON (on) to enable automatic channel switching. 3. Select OFF (off) to disable automatic channel switching. 28 Lowrance - Link-5 Operation and Installation Instructions

29 4-9 DSC Test Reply (TEST REPLY) You can respond to incoming DSC TEST calls with an automatic response or with a manual response. MANUAL AUTO manual responce is required, press ENT to confirm or press EXIT to cancel. automatically replies after a 10 second delay with an ACK to any incoming DSC TEST call. DSC SETUP LL REPLY AUTO SWITCH TEST REPLY TEST REPLY MANUAL AUTO 4-10 Set the inactivity timer (TIMEOUT) You can set the inactivity timer with the following options: AUTOMATED NON AUTO you can set the inactivity timer to automatically timeout after a period of inactivity for the following two categories: NON-DISTRESS or DISTRESS Timeout options are: DISTRESS: NO TIMEOUT; 5 MINS; 10 MINS (default is NO TIMEOUT) NON-DISTR: NO TIMEOUT; 10 MINS; 15 MINS (default is 15 MINS) you can set the inactivity timer to exit any non-automated procedure activity. Timeout options are: NO TIMEOUT; 10 MINS; 15 MINS (default is 10 MINS) Note: If NO TIMEOUT is selected, then you must press the EXIT key to exit the procedure. Example: to set a 10 minute TIMEOUT for non-automated functions: 1. Select TIMEOUT, then select NON AUTO 2. Select desired timeout period: NO TIMEOUT, 10 MINS or 15 MINS DSC SETUP AUTO SWITC TEST REPLY TIMEOUT TIMEOUT AUTOMATED NON AUTO NON AUTO NO TIMEOUT 10 MINS 15 MINS In this example, 10 MINS has been selected, meaning the radio will exit any non-automated procedure after a period of 10 minutes of non-activity. Lowrance - Link-5 Operation and Installation Instructions 29

30 Section 5 - Sending and Receiving DSC Calls 5-1 What is DSC? DSC (Digital Selective Calling) is a semi-automated method of establishing VHF, MF, and HF radio calls. It has been designated as an international standard by the IMO (International Maritime Organization) and is part of the GMDSS (Global Maritime Distress and Safety System). Currently, you are required to monitor the VHF Distress Channel 16, but DSC will eventually replace listening watches on distress frequencies and will be used to broadcast routine and urgent maritime safety information. DSC enables you to send and receive calls from any vessel or coast station that is equipped with DSC functionality, and within geographic range. Calls can be categorised as distress, urgency, safety, or routine, and DSC selects a working channel automatically. 5-2 Sending DSC calls WARNING A valid USER MMSI must be entered into this radio before these DSC functions can be used. See 4-2 Enter Your USER MMSI (USER MMSI). Press CALL to show the types of DSC call that can be made. The following options are available through CALL key: INDIVIDUAL Make a individual call or acknowledgement to a new caller or a buddy. See Section 5-2-1, 5-2-2, and LAST CALL Show the details of the most recent incoming call. See Section GROUP Make a call to one of your three groups. See Section ALL SHIPS Make an All Ships call. See Section CALL LOG Show the details of the 20 most recent incoming calls. See Section DISTR LOG Show the details of the 10 most recent distress calls. See Section SENT CALL Show the details of the 20 most recent sent calls. See Section LL REQUEST Request the LL position of a buddy. See Section DSC TEST Make a DSC TEST call. See Section MMSI/GPS Show the programmed MMSI and GPS information See Section Lowrance - Link-5 Operation and Installation Instructions

31 DSC CALL INDIVIDUAL LAST CALL GROUP Note that only three DSC call types can be shown at any one time on the screen. Press + or - to scroll up and down the DSC call types until the cursor is positioned at the desired option. Then press ENT. The DSC call types are: Make a Routine Call (INDIVIDUAL) You can call any other person that has another DSC equipped radio. DSC CALL INDIVIDUAL LAST CALL GROUP INDIVIDUAL ROUTINE SAFETY URGENCY MANUAL MMSI INDIVIDUAL ROUTINE INTER-SHIP INDIVIDUAL ROUTINE SEND? INDIVIDUAL ROUTINE CALLING INDIVIDUAL ROUTINE WAIT... 00:00 INDIVIDUAL ROUTINE ACK FROM 00:00 1. Press CALL to enter DSC mode, then select INDIVIDUAL. This allows you to call another person. 2. Press ENT, the arrow is pointing to <ROUTINE>. However, you can select one of the following call priorities: ROUTINE, SAFETY, URGENCY. To make a Routine call, press ENT to select MANUAL NEW to call a person that is not in your buddy list, otherwise select the name of your buddy. Press ENT. If you selected MANUAL NEW, you need to enter the user MMSI and then press ENT. Note: If the MMSI is for a Coast Station, enter the 7 digits then press ENT twice. 3. Select the Inter-ship working channel and press ENT. The radio automatically lists all Inter-ship (Simplex) channels that can be used. (Note: If you wish to use a Duplex channel (Duplex channels cannot usually be called), rotate the dial until Manual appears, then select your channel of choice. If the call is to a Coast Station (MMSI begins with 00), the radio will recognize this and specify the correct channel to talk on. 4. The radio summarizes the call details and asks for confirmation to send the call (SEND?). Press ENT to send the call. The radio goes to CH70 and the TX annunciator is displayed on the screen while the DSC call is being sent. 5. The radio then waits for an acknowledgement and displays the elapsed time since the call was sent. 6. If the call is acknowledged (ACK), press PTT to talk. If there is no reply, retry making the call. See Section Lowrance - Link-5 Operation and Installation Instructions 31