FKP... 5 PRESSURE TRANSMITTER (DIRECT MOUNT TYPE) FEATURES SPECIFICATIONS. Functional specifications

Transcription

1 FKP... 5 PRESSURE TRNSMITTER (DIRECT MOUNT TYPE) The FCX III pressure transmitter accurately measures gauge pressure and transmits proportional to 20m signal. The transmitter utilizes the unique micromachined capaci- tie silicon sensor with state-of-the-art microprocessor tech- nology to proide exceptional performance and functionality. FETURES 1. High accuracy ±0.1% 0.1% accuracy is a standard feature. Fuji s microcapacitance silicon sensor assures this accuracy for all eleated or suppressed calibration ranges without additional adjustment. 2. Minimum enironmental influence The dance Floating Cell design which protects the pressure sensor against changes in temperature, and oerpressure substantially reduces total measurement error in actual field applications. 3. Fuji/HRT bilingual communications protocol FCX III series transmitter offers bilingual communications to speak both Fuji proprietary protocol and HRT. ny HRT compatible deices can communicate with FCX III.. pplication flexibility Various options that render the FCX III suitable for almost any process applications include: Full range of hazardous area approals uilt-in RFI filter and lightning arrester 5-digit LCD meter with engineering unit 5. urnout current flexibility (Under Scale: 3.2 to.0m, Oer Scale: 20.0 to 22.5m) urnout signal leel is adjustable using Model FXW Hand Held Communicator (HHC) to comply with NMUR NE3. 6. Dry calibration without reference pressure Thanks to the best combination of unique construction of mechanical parts (Sensor unit) and high performance electronics circuit (Electronics unit), reliability of dry calibration without reference pressure is at equal leel as wet calibration. SPECIFICTIONS Functional specifications Serice: Liquid, gas, or apour Span, range and oerrange limit: Type Min. FKP { } FKP {0.3125} FKP {1.875} FKP {6.25} Span limit [kpa] {bar} Max. 130 {1.3} 500 {5} 3000 {30} {100} Range limit [kpa] {bar} 100 to { 1 to + 1.3} 100 to { 1 to + 5} 100 to { 1 to +30} 100 to { 1 to + 100} Oerrange limit [MPa] {bar} 1 {10} 1.5 {15} 9 {90} 15 {150} Lower range limit (acuum limit) is; Silicone fill sensor: See Fig. 1 Fluorinated fill sensor: 66kPa abs (500mmHg abs) at below 60 C Output signal: to 20m DC with digital signal superimposed on the to 20m signal. TG-L1000-0E JUL. 2009J

2 Power supply: Transmitter operates on 10.5V to 5V DC at transmitter terminals. 10.5V to 32V DC for the units with optional arrester. Load limitations: see figure below Load resistance [Ω] Ω R= E-10.5 (Imax+0.9)x Ω Operating area 2V 5V V Power oltage (DC) E[ V ] Note: For communication with HHC (1) (Model: FXW), min. of 250Ω is required. Hazardous locations: See TLE3 Zero/span adjustment: Zero and span are adjustable from the HHC (1). Zero and span are also adjustable externally from the adjustment screw. Damping: djustable from HHC or local configurator unit with LCD display. The time constant is adjustable between 0.06 to 32 seconds. Zero eleation/suppression: Zero can be eleated or suppressed within the specified range limit of each sensor model. Normal/reerse action: Selectable from HHC (1). Indication: nalog indicator or 5-digit LCD meter, as specified. urnout direction: Selectable from HHC (1) If self-diagnostic detect transmitter failure, the analog signal will be drien to either Output Hold, Output Oerscale or Output Underscale modes. Output Hold : Output signal is hold as the alue just before failure happens. Output Oerscale : djustable within the range 20.0m to 22.5m from HHC (1) Output Underscale : djustable within the range 3.2m to.0m from HHC [m] Oer scale urnout Temperature limit: mbient: 0 to +85 C ( 20 to +80 C for LCD indicator) ( 0 to +60 C for arrester option) ( 10 to +60 C for fluorinated oil fill transmitter) For explosionproof units (flameproof or intrinsic safety), ambient temperature must be within the limits specified by each standard. Process: 0 to +100 C for silicone fill sensor 20 to +80 C for fluorinated oil fill sensor Storage: 0 to +90 C Humidity limit: 0 to 100% RH Communication: With HHC (1) (Model FXW, consult Data Sheet No. EDS8-7), following items can be remotely displayed or configured. Note: HHC s ersion must be higher than 7.0 (or FXW 1 ), for FCX III. Local configurator with LCD display (option): Local configurator with 3 push button and LCD display can support following items. Items y communication with FXW y local configurator (with 3 push button) Display Set Display Set Tag No. Model No. Serial No. & Software Version Engineering unit Range limit Measuring range Damping Output mode urnout direction Calibration Output adjust Data Self diagnoses Printer (In case of FXW with printer option) External switch lock Transmitter display Linearize Rerange Saturate current Write protect History Calibration history mbient temperature history EMC Conformity: EN : 2006 Under scale urnout Normal operating range Probable under range Probable oer range Output limits conforming to NMUR NE3 by order. Loop-check output: Transmitter can be configured to proide constant signal 3.2m through 22.5m by HHC. (Note) (1) HHC: Hand Held Communicator 2 TOKYO KEISO CO., LTD. TG-L1000-0E

3 Performance specifications ccuracy rating: (including linearity, hysteresis, and repeatability) For spans greater than 1 /10 of URL: ±0.1% of span For spans below 1 /10 of URL : ±( URL Span ) % of span Stability: ±0.2% of upper range limit (URL) for 10 years (In case of 6th digit code 2, 3, ) Temperature effect: Effects per 55 C change between the limits of 0 C and +85 C Zero shift : ± ( Total effect: ± ( URL Span ) %/28 C URL Span ) %/28 C Oerrange effect: Zero shift, 0.3% of URL for any oerrange to maximum limit Supply oltage effect: Less than 0.05% of calibrated span per 10V Update rate: 60 msec Step response: Time constant: 0.08s (at 23 C) Dead time: about 0.12s (without electrical damping) Mounting position effect: Zero shift, less than 0.1kPa {1mbar} for a 10 tilt in any plane. No effect on span. This error can be corrected by adjusting zero. (Double the effect for fluorinated fill sensors) Dielectric strength: 500V C, 50/60Hz 1 min., between circuit and earth Insulation resistance: More than 100MW at 500V DC Internal resistance for external field indicator: 12W or less. Physical specifications Electrical connections: G 1 /2, 1 /2-1 NPT, Pg13.5, or M conduit, as specified. Process connections: 1 /2-1NPT, Rc 1 /2, Rc 1 / or 1 /-18NPT, as specified. Process-wetted parts material: Material code (7th digit in Code symbols) V Process coer 316 stainless steel Diaphragm 316L stainless steel Wetted sensor body 316 stainless steel Non-wetted parts material: Electronics housing: Low copper die-cast aluminum alloy (standard), finished with polyester coating. Fill fluid: Silicone oil (standard) or fluorinated oil (Daifloil) Mounting bracket: 30 stainless steel Enironmental protection: IEC IP67 and NEM 6/6P Mounting: On 60.5mm (JIS 50 or 2) pipe using mounting bracket, direct wall mounting, or direct process mounting. Mass{weight}: Transmitter approximately 2.2kg without options. dd; 0.5kg for mounting bracket TG-L1000-0E TOKYO KEISO CO., LTD 3

4 Optional features Indicator: plug-in turnable analog indicator (2.5% accuracy). n optional 5 digit LCD meter with engineering unit is also aailable. Local configurator with LCD display: n optional 5 digits LCD meter with 3 push buttons can support items as using communication with FXW. rrester: built-in arrester protects the electronics from lightning surges. Lightning surge immunity: kv (1.2 x 50 µs) Oxygen serice: Special cleaning procedures are followed throughout the process to maintain all process wetted parts oil-free. The fill fluid is fluorinated oil. Degreasing: Process-wetted parts are cleaned, but the fill fluid is standard silicone oil. Not for use for oxygen or chlorine measurement. NCE specification: Metallic materials for all pressure bound- ary parts comply with NCE MR Optional tag plate: n extra stainless steel tag with customer tag data is wired to the transmitter. CCESSORIES Hand-held communicator: Handy type communicator with built in battery. Silicone oil (Code:Y,G,N) [kpa abs] (mmhg abs) 101 (760) Operating pressure 20 (150) (30) 2.7 (20) Operating area -operating area Process temperature [ C ] Fig. 1 Relation between process temperature and operating pressure TOKYO KEISO CO., LTD. TG-L1000-0E

5 CODE SYMOLS Digit <Connections> Process connection 1/2-1NPT 1/2-1NPT 1/2-1NPT 1/2-1NPT Description Conduit connection G1/2 1/2-1NPT Pg13.5 M Case type <Span limit> FKP kpa {bar} { } { } { } { } <Material> Process coer Diaphragm Wetted cell body 316 stainless steel 316L stainless steel 316 stainless steel <Indicator and arrester> Indicator rrester nalog, 0 to 100% linear scale nalog, custom scale nalog, 0 to 100% linear scale nalog, custom scale Digital, custom scale Digital, custom scale (Local configurator unit with LCD displey) Digital, Custom scale (Local configurator unit with LCD displey) (Local configurator unit with LCD displey) Digital, Custom scale (Local configurator unit with LCD displey) <pproals for hazardous locations> (for ordinary locations) TIIS, Flameproof (Conduit seal) (*1) TIIS, Flameproof (Cable gland seal) (*1) TIIS, Intrinsic safety FM, Flameproof (or explosionproof) (*) FM, Intrinsic safety and nonincentie FM Combined of flameproof and intrinsic safety (*) TEX Flameproof (*3) TEX Intrinsic safety TEX Type n TEX Combined of flameproof and intrinsic safety (*3) IECEx Scheme, Flameproof (*3) IECEx Scheme, Intrinsic safety CS, Flameproof (or explosionproof) (*) CS, Intrinsic safety and nonincentie NEPSI, Flameproof (or exprosionproof) NEPSI, Intrinsic safety NEPSI, Combined of flameproof and intrinsic safety <Mounting bracket> (stainless steel) <Optional specification> Stainless tag (*5) <Special application and fill fluid> Treatment Filled liquid (standard) Silicon oil Degreasing Silicon oil Oxygen serice Fluorinated oil NCE specification Silicon oil <Process adaptor> (1/2-1NPT) Rc1/ Rc1/2 1/-18NPT <Fixed code>(*6) F KP Note 1: (*1) ailable for th digit code "5", "S". Note 3: (*3) ailable for th digit code "6", "8", "T", "W". Note : (*) ailable for th digit code "6", "T". Note 5: (*5) Customer tag number can be engraed on standard stainless steel name plate. If extra tag plate is required select "". Note 6: (*6) In case of hazardous location type, tag plate is made by Fuji Electric Systems Co., LTD. Note Note 1 Note 1 Note Note Note 3 Note 3 Note 3 Note Note 5 Note V D E F H L P Q S C G D H V X K P M R T E J F S U C Y Y G N Y C Z Digit No. of code TG-L1000-0E TOKYO KEISO CO., LTD 5

6 OUTLINE DIGRM (Unit:mm) 6 TOKYO KEISO CO., LTD. TG-L1000-0E

7 TLE 3 uthorities Intrinsic safety uthorities Flameproof TEX Factory Mutual CS TIIS IECEx Scheme NEPSI Ex II 1 G Ex ia IIC T5 Tamb = 0 C to +50 C Ex ia IIC T Tamb = 0 C to +70 C Ui=28V, Ii=9.3m, Pi=0.66W, Ci=26nF (Without rrester), Li=0.6mH (Without analog indicator), Ci=36nF (With rrester), Li=0.7mH (With analog indicator) II III Di.1 Groups,, C, D, E, F, G T Entity Type X Model code 9th digit 13th digit Vmax=28V, Imax=9.3m, Pi=0.66W, Ci=35.98nF, Li=0.69mH Tamb,,D Y,G,N 0 C to +85 C L,P,1,2 Y,G,N 20 C to +80 C Q,S,,5 Y,G,N 20 C to +60 C E,F,H Y,G,N 0 C to +60 C 10 C to +60 C Di.1 Groups,, C, D I Di.1 Groups E, F, G II Di.1 Temp Code T5 Tamb max = +50 C Temp Code T Tamb max = +70 C Vmax=28V, Imax=9.3m, Ci=25nF (Without rrester), Ci=36nF (With rrester), Li=0.6mH (Without analog meter), Li=0.7mH (With analog meter) Ex ia IIC T Tamb max = +60 C Ui=28V, Ii=9.3m, Pi=0.66W, Ci=38.nF, Li=0.69mH Ex ia IIC T Tamb = 0 C to +70 C Ex ia IIC T5 Tamb = 0 C to +50 C Ui=28V, Ii=9.3m, Pi=0.66W, Ci=26nF (Without rrester), Li=0.6mH (Without analog indicator), Ci=36nF (With rrester), Li=0.7mH (With analog indicator) Ex ia IIC T Ex d II+H2 T6 / Ex ia IIC T Model code 9th digit 13th digit Tamb,,D Y,G,N 0 C to +85 C L,P,1,2 Y,G,N 20 C to +80 C Q,S,,5 Y,G,N 20 C to +60 C E,F,H Y,G,N 0 C to +60 C 10 C to +60 C Ui=2.V, Ii=113m, Pi=1W, Ci=35.98nF, Li=0.69mH TEX Factory Mutual CS IECEx Scheme TIIS NEPSI uthorities TEX Factory Mutual (pending) Ex II 2 GD Ex d IIC T6 IP66/67 T85 C Tamb = 0 C to +65 C Ex d IIC T5 IP66/67 T100 C Tamb = 0 C to +85 C Di.1 Groups, C, D T6 Type X I III Di.1 Groups E, F, G T6 Type X Tamb max = +60 C Di.1 Groups C, D I Di.1 Groups E, F, G II Di.1 Note) Seal Not Required enclosure is allowed. Ex d IIC T5 IP66/67 Tamb = 0 C to +85 C Ex d IIC T6 IP66/67 Tamb = 0 C to +65 C Ex do II+H 2 T Tamb max = +60 C Maximum process temp. = +120 C Ex d II+H 2 T6 Tamb = 0 C to +60 C Type n Nonincendie Ex II 3 GD EEx nl IIC T5 Tamb = 0 C to +50 C EEx nl IIC T Tamb = 0 C to +70 C Specific Parameters: Model without arrester: Ui=2.V, Ii=113m, Pi=1W, Ci=25.18nF, Li=0.69mH Model with arrester: Ui=32V, Ii=113m, Pi=1W, Ci=35.98nF, Li=0.69mH EEx nl IIC T5 Tamb = 0 C to +50 C EEx nl IIC T Tamb = 0 C to +70 C Specific Parameters: Model without arrester: Umax=2.V, Imax=113m, Pmax=1W, Model with arrester: Umax=32V, Imax=113m, Pmax=1W II III Di.2 Groups,, C, D, F, G T Entity Type X Model code 9th digit 13th digit Tamb,,D Y,G,N 0 C to +85 C L,P,1,2 Y,G,N 20 C to +80 C Q,S,,5 Y,G,N 20 C to +60 C E,F,H Y,G,N 0 C to +60 C 10 C to +60 C CS Di.2 Groups,, C, D I Di.2 Groups E, F, G II Di.2 Temp Code T5 Tamb max = +50 C Temp Code T Tamb max = +70 C Vmax=28V, Ci=25.18nF (Without rrester), Ci=35.98nF (With rrester), Li=0.69mH * Specification is subject to change without notice. Head Office : Shiba Toho uilding, Shibakoen, Minato-ku, Tokyo Tel : (KEY) ; Fax : oerseas.sales@tokyokeiso.co.jp ; URL : TG-L1000-0E TOKYO KEISO CO., LTD 7