Data Sheet TLI242A DATA SHEET. LED BLU Driver TLI242A. TLI242 Series [RoHS Compliant] Analog Zero Dimming
|
|
- Daisy Price
- 5 years ago
- Views:
Transcription
1 DATA SHEET LED BLU Driver TLI242A TLI242 Series [RoHS Compliant] TLI242A TLI242P TLI242AZ TLI242AZ-VR Analog Dimming PWM Dimming Analog Zero Dimming VR (5K) Zero Dimming March
2 RECORD OF REVISION No Description Revision Page Date APPLICATION This document specified detailed Product Requirement of TLI242A LED Driver 2. TEST & TARGET PANEL LCD 19.0 ~ 21.5 & 23.0 Inch LED BLU : 2CH, 4CH 3. FEATURES 1) LED Output Selection Jumper : 60mA ~ 120mA (Ex : 60mA, 70mA, 80mA, 100mA, 110mA, 120mA) 2) LED Output Channel Select : 2ch, 4ch (Main) 3) Variable output Voltage Support <VLED> : 7.6V ~ 57.6V 4) Analog Dimming Control Input ( DC 0~3.3V or 5V ) : DC Burst Dimming 5) PWM Dimming Output Frequency : 3~4KHz (3.5KHz) 6) Static Frequency : 220KHz ± 5kHz 7) Various Protection : OVP (Over-voltage Protection Mode) / Open / Short protection 4. ELECTRICAL CHARACTERISTICS 4.1. Absolute Maximum Ratings Item Symbol Spec Unit Remarks Input Voltage1 Vin1 10.8~24.0 V Input Voltage2 Vin V Operating Temperature Top 0~50 Storage Temperature Tstg -30 ~ 80 Relative Humidity Rh 70 % 2
3 4.2 Output Characteristics I Item SYS Condition Min. Typ. Max. Unit Input Voltage Vin ~ Vdc Input Current Lin Vin=12.0~24.0V Dim=0V A Output Voltage Vout Vin=12.0~24.0V Dim=0V ~ V Output Current BUL ON/OFF Control Lout(Max) Vin=12.0~24.0V Dim=0V ~ Lout(Min) Vin=12.0~24.0V Dim=3.6V ~ ON OFF ma V 4.3 Output Characteristics II Item Volt Input Condition Input Current LEDx Volt LEDx Current Jumper SW1 SW2 SW3 SW4 M240HW02 V.6 (110mA) < 4 CH > Vin=12V Vin=24V Dim=0V 1.97A 45.0V 108.7mA Dim=5.0V 0.27A 36.2V 14.5mA Dim=0V 0.92A 44.7V 109mA Dim=5.0V 0.13A 36.0V 14.7mA OFF ON ON ON T215HVN01 60mA < 4 CH > Vin=12V Vin=24V Dim=0V 1.25A 54.2V 58.2mA Dim=5.0V 0.16A 43.7V 7.6mA Dim=0V 0.61A 54.7V 58.9mA Dim=5.0V 0.08A 43.7V 7.3mA OFF OFF ON OFF LM215WF4- TLE1 110mA < 2 CH > Vin=12V Vin=24V Dim=0V 1.04A 49.8V 108.0mA Dim=5.0V 0.14A 41.3V 13.6mA Dim=0V 0.52A 49.8V 108.0mA Dim=5.0V 0.07A 41.4V 13.6mA OFF ON ON ON Recommend Input Voltage : LED Converter Power Consumption 10~15 W : 12V Input & 24V Input / 15~25 W Over : 24V Input LED VF(Volt Forward) value is automatically voltage-controlled and run LED BLU 3
4 5. INTERFACE 5.1 Input Connecter CN 1 : 12505WR-12A00 ( YEON-HO 1.25mm 12pin ) Pin No Symbol Description 1,2,3 Vin Voltage Input : 12.0~24.0V (typ) 4,5,7,8,10,12 GND Ground 6 N.C No Connection 9 On / Off LED Drive Signal ( Active High ) 11 Dim 0V (Max) ~ 5V (Min) 5.2 Output Connector CN2 : 12505WR-06A00 ( YEON-HO 1.25mm 6Pin ) Pin No Symbol Description Remarks 1 FB1 Channel1 Current Feedback 2 CH Setting 2 FB4 Channel4 Current Feedback 4 CH Setting 3 V LED System output V LED 4 V LED System output V LED 5 FB3 Channel3 Current Feedback 3 CH Setting 6 FB2 Channel2 Current Feedback 2 CH Setting CN3 : 05010HR-H06C3 ( YEON-HO FFC 0.5mm 6Pin ) Pin No Symbol Description Remarks 1 FB1 Channel1 Current Feedback 2 CH Setting 2 FB4 Channel4 Current Feedback 4 CH Setting 3 V LED System output V LED 4 V LED System output V LED 5 FB3 Channel3 Current Feedback 3 CH Setting 6 FB2 Channel2 Current Feedback 2 CH Setting 4
5 CN4 : 10019HR-H06 ( YEON-HO FFC 1.0 mm 6Pin ) Pin No Symbol Description Remarks 1 FB 1 Channel1 Current Feedback 2 CH Setting 2 FB 2 Channel4 Current Feedback 4 CH Setting 3 V LED System output V LED 4 V LED System output V LED 5 FB3 Channel3 Current Feedback 3 CH Setting 6 FB2 Channel2 Current Feedback 2 CH Setting CN5 : 10019HR-H04 ( YEON-HO FFC 1.0 mm 6Pin ) Pin No Symbol Description Remarks 1 NC No Connection NC 2 FB1 Channel1 Current Feedback 2 CH Setting 3 FB 2 Channel2 Current Feedback 2 CH Setting 4 V LED System output V LED 5.3 Jumper setting J1 : ( SW 1~4 ) LED Current Setting Setting SW1 SW2 SW3 SW4 LED Current LED Current ( Approximation ) (Actual output) Set 1 ON ON ON ON 120mA 115.0mA Set 2 OFF ON ON ON 110mA 108mA Set 3 ON OFF ON ON 100mA 97.0mA Set 4 OFF ON OFF ON 80mA 78.6mA Set 5 ON ON ON OFF 70mA 69.6mA Set 6 OFF OFF ON OFF 60mA 61.1mA J1 : ( SW 5 ) Channel of LED String Selection < 2 & 4 Ch > Setting CH Symbol NUMSEL ON 2 CH FB1, FB2 : Operation FB3, FB4 : No Operation GND OFF 4 CH FB1, FB2, FB3, FB4 : Operation NC SW1~4 SW
6 5.4 Panel Select Support Guide Vendor Size Panel Connector CH Pitch LED Volt LED Current Power Consumption LB190E02-SL01 CN3 FFC 6Pin 4 0.5mm 30V 110mA 13.2W LG 19.0 LM190E09-TLA1 CN3 FFC 6Pin 4 0.5mm 51.2V 60mA 12.29W LM190E09-TLC1 CN2 Housing 6Pin 2 1.0mm 47.3V 100mA 9.5W LM190E09-TLD1 CN2 Housing 6Pin 2 1.0mm 44.3V 60mA 5.3W LC215EUE-TCA1 CN5 FFC 4Pin 2 1.0mm 57.6V 110mA 12.7W LM215WF4-TLA1 CN5 FFC 4Pin 2 1.0mm 57.6V 110mA 12.7W LM215WF4-TLC1 CN5 FFC 4Pin 2 1.0mm 57.6V 110mA 12.7W LG 21.5 LM215WF3-SLE1 CN2 Housing 6Pin mm 50.4V 120mA 12.1W LM215WF4-TLG1 CN2 Housing 6Pin mm 44.1V 120mA 10.6W LM215WF3-SLC1 CN4 FFC 6pin 4 1.0mm 41.6V 110mA 18.3W LM215WF4-TLE7 CN4 FFC 6pin 2 1.0mm 51.2V 110mA 11.26W LM215WF4-TLE1 CN4 FFC 6pin 2 1.0mm 41.6V 110mA 11.26W LG LM230WF5-TLD1 CN4 FFC 6pin 2 1.0mm 51.2V 120mA 13.82W Tested Panel Vendor Size Panel Connector CH LED Volt LED Current Pitch LG 21.5 LC215EUE-TCA1 CN5 FFC 4Pin V 110mA 1.0mm LM215WF4-TLE1 CN4 FFC 6pin V 110mA 1.0mm AU 21.5 T215HVN01 CN2 Housing 6Pin V 60mA 1.25mm 6
7 6. APPEARANCE ( Unit : mm ) 6.1 Dimension : 45mm (W) 75 (D) 10 (H) mm 1.6mm 6.2 PCB 1) FR-4 2) 1.6t 3) 2-Layer COIL E/L CAP Jumper 10.5mm 7
8 7. LED DRIVER GUIDE 7.1 LED Driver Description J1 : SW 1~4 (Current Setting) LED Current : 60mA~120mA J1 : SW5 2CH / 4 CH : Selection CN2 J1 Connecter 1.25mm 6pin 2/4 Ch CN1 Connecter 1.25mm 12pin LED Output : 7.3V~57.6V LED Current : 60mA~120mA FFC 0.5mm 6pin 2/4 Ch CN3 CN4 Input Voltage : 12~24V Dim ADJ : 0~5V LED Drive Signal : On / Off FFC 1.0mm 6pin 2/4 Ch CN5 FFC 1.0mm 4pin 2Ch 7. 2 LED CH Connection : CN2, CN3, CN4 (Same Connection) / CN5 ( Only 2 Ch ) 1) 2 Ch Setting 1. FB1 CN2 J1 2. FB4 3. V LED 4. V LED 5. FB3 CN3 6. FB2 LED Output : 7.3V~57.6V (Drive 3~18 LEDs in Series) LED 2 CH CN4 1. FB1 2. FB2 CN5 3. V LED 4. NC 8
9 2) 4 Ch Setting CN2 J1 CN1 CN3 LED Output : 7.3V~57.6V (Drive 3~18 LEDs in Series) CN4 LED 4 CH CN5 8. MATERIAL LIST FOR SAFETY TLI242A Symbol Name Type No Manufacturer Descripton F1 FUSE LITTLEFUSE UL FILE NO : E10480 PCB Printed Wiring Board FR-4 Woo jin - J1 SMD SW KSD-52S SW250 OTAX UL-94V-0 CN1 Connector 12505WR-12A00 YEON-HO UL : E CN2 Connector 12505WR-06A00 YEON-HO UL : E CN3 Connector 05010HR-H06C3 YEON-HO UL : E CN4 Connector 10019HR-H06 YEON-HO UL : E CN5 Connector 10019HR-H04 YEON-HO UL : E End - 9
DOCUMENTATION FOR APPROVAL
TO : Customer DATE : 05.03.3 GREEN C&C TECH Co.,Ltd 5,JINWISANDAN-RO, JINWI-MYEON PYEONGTAEK-CITY, KYEONGGI-DO KOREA 45-8 TEL : 8-3-373-33~35 FAX : 8-3-373-30 DOCUMENTATION FOR APPROVAL PRODUCT : LED BACKLIGHT
More informationDOCUMENTATION FOR APPROVAL
TO : CUSTOMER GREEN C&C TECH CO.,LTD 31B 2-8. JinWi-Myeon, Pyeongtaek-City, Gyeonggi-Do, Korea 451-862 TEL : 82-31-373-3623,3624,3625 FAX : 82-31-373-3610 DOCUMENTATION FOR APPROVAL PRODUCT MODEL NAME
More informationDim. Method. Parameter Min. Typ. Max. Unit Remark. Input Current AC 120V, 100% Load. Efficiency AC V,100% Load
PIFN-H030A Flat 30W LED Driver 30V - 42V / 0.66A / 27.72W(Max) Features Mechanical Outline Dimming Method: 1-10V Dimming (1V=10%) (Metal Case) - 280(L) 31(W) 26.8(H)mm Constant Current Control Active Power
More informationPiezo Ceramics DC-AC Inverter. Specification
` Piezo Ceramics DC-AC Inverter Specification Note: Actual product image may be different. Model FC01-12-06 Part No. 400-8888-010 Description Customer Hardware Rev 1.0 Document Rev 1.2 1 lamps with wide
More informationPiezo Ceramics DC-AC Inverter. Specification
Piezo Ceramics DC-AC Inverter Specification Note: Actual product image may be different. Model FC01-12-03 Part No. 400-8888-047 Description Customer Hardware Rev 1.0 Document Rev 1.1 1 lamps with wide
More informationPanelMatch PRODUCT HIGHLIGHT , OR POTENTIOMETER. PWM Signal. Potentiometer PACKAGE ORDER INFO
DESCRIPTION The is a Dual 4W Output Direct Drive CCFL (Cold Cathode Fluorescent Lamp) Inverter Module specifically designed for driving LCD backlight lamps. It is ideal for driving typical 6.4 to 10.4
More informationMicrosemi Analog Mixed Signal Group Western Avenue, Garden Grove, CA , , , Fax:
1 2 3 PanelMatch DESCRIPTION The is a Dual 6W Output Direct Drive CCFL (Cold Cathode Fluorescent Lamp) Inverter Module specifically designed for driving LCD backlight lamps. It is ideal for driving typical
More information15 W DC/DC CONVERTERS. SERIES DESCRIPTION Page. PC15WR 2:1 Input Range 2 2 x 1 Metal Can Package 2kv Isolation
15 W DC/DC CONVERTERS SERIES DESCRIPTION Page PC15WR 2:1 Input Range 2 2 x 1 Metal Can Package 2kv Isolation PC15WR4 4:1 Input Range 6 2 x 1 Metal Can Package 2kv Isolation CTC TECHNOLOGY CO.,LTD. DC /
More informationXLSEMI. Datasheet. 3A 150KHz 30V Buck DC to DC Converter. Features. General Description. Applications
Features Wide 4.75V to 30V Input Voltage Range 3.3V,5V,12V, and adjustable versions Output Adjustable from 1.23V to 28V Maximum Duty Cycle 100% Minimum Drop Out 1.5V Fixed 150KHz Switching Frequency 3A
More informationRangeMAX DIGITAL DIMMING DUAL LAMP CCFL INVERTER MODULE
3 RangeMAX DESCRIPTION The LXMG6 Direct Drive CCFL (Cold Cathode Fluorescent Lamp) Inverter Modules are specifically designed for driving two lamp LCD backlight displays. Similar to the LXMG60, the LXMG6
More information400KHz 60V 3A Switching Current Boost LED Constant Current Driver
Features Wide 5V to 48V Input Voltage Range 0.22V FB adjustable LED drive current Directly drive 16 Series 1W LED at VIN>=12V Fixed 400KHz Switching Frequency Max. 3A Switching Current Capability Up to
More informationDim. Method Isolated 0-10V, Schedule. Parameter Min. Typ. Max. Unit Remark. Nominal Input Frequency 47 50/60 63 Hz -
PIFN-W050C Programmable 50W LED Driver (Compatible NFC) 20V - 52V / 0.4A 1.4A / 50W Features Mechanical Outline (Metal Case) Active Power Factor Correction - 335(L) 29.8(W) 25.8(H)mm Constant Current Control
More informationHigh Input Voltage Adjustable 3-Terminal Linear Regulator
High Input Voltage Adjustable 3-Terminal Linear Regulator Features 13.2V to 100V Input Voltage Range Stable with output capacitor Adjustable 1.20V to 88V output regulation 5% reference voltage tolerance
More informationCOG (Chip-On-Glass) Liquid Crystal Display Module
NHD-C12864CR-FSW-GBW COG (Chip-On-Glass) Liquid Crystal Display Module NHD- Newhaven Display C12864-128 x 64 pixels CR- Model F- Transflective SW- Side White LED backlight G- STN - Gray B- 6:00 view W-
More informationSGM Channel PWM Dimming Charge Pump White LED Driver
GENERAL DESCRIPTION The SGM3145 is a high performance white LED driver. It integrates current sources and automatic mode selection charge pump. The part maintains the high efficiency by utilizing a 1 /1.5
More informationPanelMatch StayLit PRODUCT HIGHLIGHT. PWM Signal. Potentiometer. Microsemi. Lamp current 5 or 6mA per Lamp PACKAGE ORDER INFO
4 DESCRIPTION The is a Dual 6W Output Direct Drive CCFL (Cold Cathode Fluorescent Lamp) Inverter Module specifically designed to be compatible with variety of LCD panels that have both lamps on one side
More informationPanelMatch PRODUCT HIGHLIGHT INPUT. PWM Signal. Lamp Current 10 to 14mA in Steps PACKAGE ORDER INFO
4 PanelMatch DESCRIPTION The ¹ is a 10W dual Output Direct Drive CCFL (Cold Cathode Fluorescent Lamp) Inverter Module specifically designed to be compatible with a variety of LCD panels the have both lamps
More informationXLSEMI. Datasheet. 2A 150KHz 40V Buck DC to DC Converter. Features. General Description. Applications
Features Wide 4.75 to 40V Input Voltage Range 3.3V,5V,12V, and adjustable versions Output Adjustable from 1.23V to 38V Maximum Duty Cycle 100% Minimum Drop Out 1.5V Fixed 150KHz Switching Frequency 2A
More informationNHD WX-CoTFH-V#I041
NHD-320240WX-CoTFH-V#I041 Graphic Liquid Crystal Display Module NHD- Newhaven Display 320240-320 x 240 Pixels WX- Display Type: Graphic Co- Model T- White LED Backlight F- FSTN (+) H- Transflective, 6:00
More informationSpecifications ( typical at 25 C, nominal input voltage, rated output current unless otherwise specified )
Features Regulated Converters Description UL Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming Short Circuit and Overtemperature Protected
More informationAll the companies. Product Drawing
MESSRS : All the companies CUSTOMER'S PRODUCT NAME: TDK PRODUCT NAME: DC/DC CONERTER UNIT ALD-21412PJ111 *Notice is not contract. This is only technical data. This technical data may change internal description
More informationNewhaven Display International, Inc Galvin Ct. Elgin IL, Ph: Fax:
NHD-TFT40 40-pin TFT Breakout NHD- Newhaven Display TFT- TFT Breakout 40-40-pin Connector Newhaven Display International, Inc. 2661 Galvin Ct. Elgin IL, 60124 Ph: 847-844-8795 Fax: 847-844-8796 www.newhavendisplay.com
More informationAC - DC 150W LED Driver MDC150 Single Output Series
Features Built-in 10KV lightning surge protection (EN61000-4-5) 90 ~ 305Vac full range input; Active PFC Output voltage range up to 58Vdc for outdoor lighting Aluminum case IP65/ IP67 waterproof Dual mode
More informationSeries AMLBW-Z Up to 700mA Step Up LED Driver
Models Single output Model Input Voltage (V) Series FEATURES: Step UP DC/DC LED driver Operating Temperature 0ºC to +8ºC Constant current output Open and Short circuit LED Protection High efficiency up
More informationDOCUMENTATION FOR APPROVAL
TO : Customer DTE : 08..0 Co.,Ltd,JINWISNDN-RO, JINWI-MYEON PYEONGTEK-CITY, KYEONGGI-DO KORE -8 TEL : 8--7-~ FX : 8--7-0 DOCUMENTTION FOR PPROVL PRODUCT : LED BCKLIGHT DRIVER (RoHS) MODEL NME : GCCT NME
More informationMP V, 700kHz Synchronous Step-Up White LED Driver
The Future of Analog IC Technology MP3306 30V, 700kHz Synchronous Step-Up White LED Driver DESCRIPTION The MP3306 is a step-up converter designed for driving white LEDs from 3V to 12V power supply. The
More informationTS2509 3A / 500KHz PWM Buck Converter
SOP-8 Pin Definition: 1. FB 8. Vss 2. EN 7. Vss 3. Comp 6. SW 4. Vcc 5. SW General Description TS2509 is step-down switching regulator with PWM control and with build in internal PMOS. TS2509 provides
More informationSeries AMLDV-NZ Up to 700mA LED Driver
FEATURES: Click on Series name for product info on aimtec.com Models Single output Model Input Voltage (V) Maximum Rated Current (ma) Efficiency Max (%) AMLDV-43-NZ 5.5-4 3.3-36 3 6 AMLDV-435-NZ 5.5-4
More informationAC - DC 120~150W LED Driver MDC120 Single Output Series
Features Built-in 10KV lightning surge protection (EN61000-4-5) 90 ~ 305Vac full range input; Active PFC Output voltage range up to 430Vdc for outdoor lighting Aluminum case IP65/ IP67 waterproof Dual
More informationAC - DC 96W LED Driver MDC100 Single Output Series
AC - DC LED Driver Features Built-in 10KV lightning surge protection (EN61000-4-5) 90 ~ 305Vac full range input; Active PFC Output voltage range up to 58Vdc for outdoor lighting Aluminum case IP65/ IP67
More informationMESSRS : Product Drawing. TDK-Lambda Corporation. All the companies CUSTOMER'S PRODUCT NAME: DC/DC CONVERTER UNIT ALD PJ111 TDK PRODUCT NAME:
MESSRS : All the companies CUSTOMER'S PRODUCT NAME: TDK PRODUCT NAME: DC/DC CONERTER UNIT ALD-214012PJ111 Corporation PREPARED BY APPROED BY AUTHORIZED BY K.Oshima Sept./28th/2009 K.Yamaishi Sept./28th/2009
More informationHigh-Efficiency, 40V White LED Driver with Dimming Control
High-Efficiency, 40V White LED Driver with Dimming Control Description The is a step-up DC/DC converter specifically designed for driving WLEDs with a constant current. The can drive up 10 white LEDs in
More informationIS32LT V, 350MA, 4-CHANNEL CONSTANT CURRENT REGULATOR WITH OTP FOR AUTOMOTIVE LIGHT
DESCRPTON The S32LT3117 is designed for automotive lighting applications such as map light, dome light, tail light and daytime running lights. This device is a 4-channel, linear regulated, constant current
More information(Typical at Ta = +25 C, nominal input voltage, rated output current unless otherwise specified.) Electrical Specifications ±5%
GPLD80B 0mA High Efficiency StepUP LED Driver Features RoHScompliant "x" case Package Power LED Driver Constant Current Output (±% Output Current Accuracy) LED Driver Rated Current 0mA Soft Start Wide
More informationNHD MF ATXI# T 1
NHD 4.3 480272MF ATXI# T 1 TFT (Thin Film Transistor) Color Liquid Crystal Display Module NHD Newhaven Display 4.3 4.3 Diagonal 480272 480xRGBx272 pixels MF Model A Built in driver / NO Controller T White
More informationRecord of Revision. Version Revise Date Page Content Final Spec. 2006/10/17 Initial Release 01
Record of Revision Version Revise Date Page Content Final Spec. 2006/10/17 Initial Release 01 Contents: 1.1. T-CON Board Block Drawing...1 1.2. Pin Assignment...2 1.2.1. Input section...2 1.2.2. TFT LCD
More informationAC - DC 96W LED Driver MDC100 Single Output Series
Features Built-in 10KV lightning surge protection (EN61000-4-5) 90 ~ 305Vac full range input; Active PFC Output voltage range up to 58Vdc for outdoor lighting Aluminum case IP65/ IP67 waterproof Dual mode
More informationIS31LT V, 350MA, 4-CHANNEL CONSTANT CURRENT REGULATOR WITH OTP
DESCRIPTION The IS31LT3117 is a 4-channel, linear regulated, constant current LED driver which can sink 4 equal currents of up to 350mA per channel to drive high brightness LEDs over an input voltage range
More informationPRODUCT HIGHLIGHT LXMG SW1 SW2 SW3 SW4. PWM Signal ORDER INFORMATION. Part Number Input Connector Output Connector
DESCRIPTION KEY FEATURES module is a boost white LED driver for medium size LCD LED backlight panels. It is designed to drive up to three strings of LEDs to a maximum of 35V at up to 50mA per string. The
More informationDATASHEET & RELIABILITY DATA
DATASHEET & RELIABILITY DATA KSP5 SERIES 오디피 Open Digital Power Corp. FAX : 82-31-445-7388 1 Contents - Introduction 3~4 page - Datasheet 5~13 page 1. Internal Circuit Architecture 2. Maximum Ratings 3.
More informationHRS50 Series 50W isolated DC/DC converters
HRS50 Series 50W isolated DC/DC converters Features High Efficiency Wide operating temperature range ( -40 C to +85 C ) Wide 2:1 input range Standard half brick size Six side shield Input Output Isolated
More informationPin Configurations EN 1 8 GND Table 1 Pin Description VIN 2 7 GND FB 3 6 SW NC 4 5 SW Figure2. Pin Configuration of (Top View) Pin Number Pin Name Des
Features Wide 3.6V to 24V Input Voltage Rang 0.22V Constant Current Sense Voltage Directly drive 3~8 Series 1W LED Fixed 400KHz Switching Frequency Max. 2A Switching Current Capability Up to 92% efficiency
More informationNHD-C12864WO-B1TGH#-M
NHD-C12864WO-B1TGH#-M COG (Chip-On-Glass) Liquid Crystal Display Module NHD- Newhaven Display C12864-128 x 64 Pixels WO- Display Type: COG B1- Model T- White LED backlight G- STN- Gray H- Transflective,
More informationAdvanced Monolithic Systems
Advanced Monolithic Systems FEATURES 2A, 0.2Ω, internal switch Operating voltage as low as 2.7V 600 khz operation frequency Over temperature protection 8-Lead SOIC-EDP package 2A SWITCH STEP-UP DC/DC CONVERTER
More informationSatellite STB Bluetooth Speaker Large TFT screen bias Other application which needs high voltage and high current generation
Description The is a high efficiency step-up converter with an internally integrated 20V power MOSEFT. It runs with an optimal 1MHz frequency that enables the use of small external components while still
More information60W 75W 80W 81.6W 81W 82.8W 81.9W 81.6W 81W
SPECIFICATION MODEL OUTPUT INPUT PROTECTION - - -0-4 -0 - -4-48 -4 DC VOLTAGE V V 0V 4V 0V V 4V 48V 4V CONSTANT CURRENT REGION Note.4 7. ~V 9 ~ V ~ 0V 4.4 ~ 4V 8 ~ 0V. ~ V. ~ 4V 8.8 ~ 48V.4 ~ 4V RATED
More informationBoost (Step-up) WLED Driver with OVP
Boost (Step-up) WLED Driver with OVP DESCRIPTION The TS19371 is a step-up DC/DC converter specifically designed to drive white LEDs with a constant current. The device can drive up to 126 LEDs (9S14P)
More informationLSP5504. PWM Control 2A Step-Down Converter. Applications. General Description. Features LSP5504. Typical Application Circuit
Applications Cellular Phones PC Motherboard LCD Monitor Graphic Card DVD-Video Player Telecom Equipment ADSL Modem Networking power supply Networking power supply Microprocessor core supply Printer and
More informationXLSEMI. Datasheet. 5A 150KHz 36V Buck DC/DC Converter With Constant Current Loop. Features. General Description. Applications
Features Wide 8V to 36V Input Voltage Range Output Adjustable from 1.25V to 32V Minimum Drop Out 0.3V Fixed 150KHz Switching Frequency Maximum 5A Switching Current Internal Optimize Power MOSFET Excellent
More informationAdvanced Monolithic Systems
Advanced Monolithic Systems FEATURES Internal Power Switch Output Voltage up to 20V Up to 89% Efficiency Low 0.08µA Shutdown Supply Current Internal Current Limit Thermal Shutdown Available in 5-Pin SOT-23
More information2 - NMF SERIES. Isolated 1W Regulated Single Output. features. pin connections. description
features Output Regulation
More informationNHD-12232KZ-NSW-BBW-P
NHD-12232KZ-NSW-BBW-P Graphic Liquid Crystal Display Module NHD- Newhaven Display 12232-122 x 32 Pixels KZ- Model N- Transmissive SW- Side White LED Backlight B- STN- Blue (-) B- 6:00 Optimal View W- Wide
More information11SP 4247 LCD TV Power specification Rev 1.3 Specification
Specification 6 Date: 2012. 08. 15 1. INTRODUCTION 1.1 Scope This approval is the description related to every electrical and structural specifications and reliability For Power Supply Unit used on 4247
More informationNHD-C128128BZ-FSW-GBW
NHD-C128128BZ-FSW-GBW COG (Chip-On-Glass) Liquid Crystal Display Module NHD- Newhaven Display C128128-128 x 128 Pixels BZ- Model F- Transflective SW- Side White LED Backlight G- STN-Gray B- 6:00 Optimal
More informationCOTAG. YF KHz, 4A / 23V Step-Down Converter YF1205
General Description consists of step-down switching regulator with PWM control. These devices include a reference voltage source, oscillation circuit, error amplifier, internal PMOS and etc. provides low-ripple
More informationDIO V Step-Up LED Driver with PWM to Constant Current Dimming Mode
Rev 0.2 DIO5061 37V Step-Up LED Driver with PWM to Constant Current Dimming Mode Features Drive up to 10 serial LEDs PWM to Constant Current dimming mode Integrated 40V high current switch (1.3A limit)
More informationAdvanced Power Electronics Corp.
PWM CONTROL 2A STEPDOWN CONVERTER FEATURES DESCRIPTION Input Voltage : 3.6V to 20V Output Voltage : 0.8V to VCC Duty Ratio : 0% to 100% PWM Control Oscillation Frequency : 330KHz Typ. SoftStart(SS), Current
More informationSeries AMSRL1-78JZ Up to 12 Watt DC-DC Switching Regulator
Click on Series name for product info on aimtec.com FEATURES: Picture Coming Soon Models Single output Model Input Voltage (V) Switching Regulator SMD Package Low Quiescent Current Efficiency Up To 95%
More informationAdd suffix /SMD/OF for open frame version with SMD solderpins (/SMD/OF-R for Tape and Reel Packaging) (b)
Features Regulated Converters Description UL Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming Short Circuit and Overtemperature Protected
More informationSPECIFICATION FOR APPROVAL
Customer Name : ( 주 ) 하이디스플레이 Date : 2011. 02. 22. SPECIFICATION FOR APPROVAL Part Name : CCFL INVERTER Customer Part No. : DS-Plus Part No. : (Voltage Control Dimming) Approval Sign Please Return 1 Copy
More informationNHD EF 20 Controller Board
NHD 7.0 800480EF 20 Controller Board TFT Controller Evaluation Board NHD Newhaven Display 7.0 7.0 Diagonal 800480 800 x 480 Pixels EF Model 20 20 pin FFC Interface (8 bit Parallel Data) SSD1963 Controller
More informationAll specifications valid at normal input voltage, full load and +25 C after warm-up time unless otherwise stated.
DPO-500 KEY FEATURES Open Frame Switching Power Supply Remote ON/OFF Function 240 Watt with Free Air Convection 500 Watt with 30CFM FAN Built-in 12V/0.3A Auxiliary Output Standby 5V@1A with Fan, @0.6A
More informationYB1506 Step-up DC-DC Converter, White LED Driver
Description The YB1506 is a step-up(boost) DC-DC converter; operate as current source to drive up to 5 white LEDs in series. Series connecting of the LEDs provides identical LED currents resulting in uniform
More informationPin Configurations Table 1 Pin Description Figure2. Pin Configuration of (Top View) Pin Number Pin Name Description 1 GND Ground Pin. 2 EN Enable Pin.
Features Wide 3.6V to 32V Input Voltage Range 0.22V FB adjustable LED drive current Directly drive 11 Series 1W LED at VIN>=12V Fixed 180KHz Switching Frequency Max. 5A Switching Current Capability Up
More informationS24SP05012 series 60W Single Output DC/DC Converter
Model List Model Number S24SP05012 Input Voltage (Range) Output Voltage Output Current Input Current (typ input voltage) Load Regulation Maxcapacitive Load (Cap ESR>=10mohm;Full Efficiency load;5%overshoot
More informationAdd suffix /W/X3 for wired version with both analogue and PWM dimming controls (six wires) (a)
Features Regulated Converters Selection Guide UL/ RAILWAYS Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming Short Circuit and Overtemperature
More informationAll the companies. Product Drawing
MESSRS : ll the companies CUSTOMER'S PRODUCT NME: TDK PRODUCT NME: DC/DC CONERTER UNIT LD-414012PJ126 *Notice is not contract. This is only technical data. This technical data may change internal description
More informationLD /01/2013. Boost Controller for LED Backlight. General Description. Features. Applications. Typical Application REV: 00
04/01/2013 Boost Controller for LED Backlight REV: 00 General Description The LD5861 is a wide-input asynchronous current mode boost controller, capable to operate in the range between 9V and 28V and to
More informationACE714C. Max. 3MHz, Variable Frequency Step-up DC/DC Converter
Description The veriable frequency step-up Converter drives white LEDs with a constant current to provide backlight in cell phones, PDAs, and other handheld devices. It features allowing series connection
More informationADT7350. General Description. Features. Applications. Typical Application Circuit. Sep / Rev. 0.
General Description The ADT7350 is a step-down converter with integrated switching MOSFET. It operates wide input supply voltage range from 4.5V to 24V with 1.2A peak output current. It includes current
More informationModel: AWG-F32240KFWHSGWT-A. LIQUID CRYSTAL DISPLAY MODULE MODEL: AWG-F32240KFWHSGWT-A Customer s No.: Acceptance. Approved and Checked by
Messrs. Product Specification Model: AWG-F32240KFWHSGWT-A Rev. No. Issued Date. Page. A 2008/11/20 1 / 1 LIQUID CRYSTAL DISPLAY MODULE MODEL: AWG-F32240KFWHSGWT-A Customer s No.: Acceptance,,, Approved
More informationDatasheet. Features. General Description. Applications
Features Wide 4.5V to 40V Input Voltage Range 3.3V,5V,12V, and adjustable versions Output Adjustable from 1.23V to 37V Maximum Duty Cycle 100% Minimum Drop Out 1.5V Fixed 150KHz Switching Frequency 3A
More informationUL/ RAILWAYS Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming
Features Regulated Converters Selection Guide UL/ RAILWAYS Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming Short Circuit Protected Pinned
More informationUNIVERSAL DIMMING INPUT "PWM", V DC LXM , OR POTENTIOMETER
RangeMAX Wide Range Dimming, Single Output Inverter. The LXM1612-12-xx series of Direct Drive CCFL (Cold Cathode Fluorescent Lamp) Inverter Modules are specifically designed for driving LCD backlight lamps.
More informationSeries AMLD-IZ Up to 2000mA LED Driver
FEATURES: Click on Series name for product info on aimtec.com Up to 2mA LED Driver High Power LED Driver Constant Output Current Wide (7:1) Input Voltage Range High Efficiency (Up to 96%) Remote Control
More informationLR8301 Series LESHAN RADIO COMPANY, LTD. Introduction. Features. Ordering Information. Applications Power supply for portable equipment such 1/10
SMALL PACKAGE PFM CONTROL STEP-UP DC/DC CONVERTER Introduction The is a CMOS PFM-control step-up switching DC/DC converter that mainly consists of a reference voltage source, an oscillator, and a comparator.
More information3A 52KHz 40V Buck DC to DC Converter
Features Wide 4.5V to 40V Input Voltage Range 3.3V,5V,12V and adjustable versions Output Adjustable from 1.23V to 37V Maximum Duty Cycle 100% Minimum Drop Out 1.5V Fixed 52KHz Switching Frequency 3A Constant
More information80W Single Output Switching Power Supply
SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE CONSTANT CURRENT REGION Note.4 RATED CURRENT RATED POWER RIPPLE & NOISE (max.) Note. 0mVp-p 0mVp-p 0mVp-p 0mVp-p
More informationMP4012 High-Brightness, High-Current Accuracy WLED Controller
The Future of Analog IC Technology MP4012 High-Brightness, High-Current Accuracy WLED Controller DESCRIPTION The MP4012 is a current mode controller designed for driving the high brightness Light Emitting
More informationEUP A,30V,500KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit
5A,30V,500KHz Step-Down Converter DESCRIPTION The is current mode, step-down switching regulator capable of driving 5A continuous load with excellent line and load regulation. The operates with an input
More informationNotes: Note3: without suffix, standard isolation voltage (1kVDC/1 second) with suffix /H, high isolation voltage (3kVDC/1 second)
Features Unregulated Converters Description 1W Power In SMD Package Pin Compatible With R1S -4 C To +1 C Operating Temperature @ Full Load high 3kVDC/1 Second or 1kVDC/1 Second Isolation IEC/EN/UL62368-1
More information1A, 52KHz, Step-Down Switching Regulator LM2575
FEATURES 3.3V, 5.0V, 12V and Adjustable Output Versions Adjustable Version Output Voltage Range Wide Input Voltage Range Guaranteed 1A Output Current 52kHz Fixed Frequency Internal Oscillator Voltage mode
More informationLD5857 4/15/2014. Boost Controller for LED Backlight. General Description. Features. Applications. Typical Application REV: 00
4/15/2014 Boost Controller for LED Backlight REV: 00 General Description The LD5857 is a wide-input asynchronous current mode boost controller, capable to operate in the range between 9V and 28V and to
More informationADT7350. General Description. Applications. Features. Typical Application Circuit. Aug / Rev. 0.
General Description The ADT7350 is a step-down converter with integrated switching MOSFET. It operates wide input supply voltage range from 4.5V to 24V with 1.2A peak output current. It includes current
More informationAME, Inc. PWM Control 2A Buck Converter AME5106. Applications. General Description. Features
General Description AME5106 provides low-ripple power, high efficiency, and excellent transient characteristics. The PWM control circuit is able to vary the duty ratio linearly from 0 up to 100%. This
More informationDESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION. 500KHz, 18V, 2A Synchronous Step-Down Converter
DESCRIPTION The is a fully integrated, high-efficiency 2A synchronous rectified step-down converter. The operates at high efficiency over a wide output current load range. This device offers two operation
More informationHigh Performance, Constant Current Switching Regulator For White LED
High Performance, Constant Current Switching Regulator For White LED General Description The is a.mhz PWM boost switching regulator designed for constant- current white LED driver applications. The can
More information1.0MHz,24V/2.0A High Performance, Boost Converter
1.0MHz,24V/2.0A High Performance, Boost Converter General Description The LP6320C is a 1MHz PWM boost switching regulator designed for constant-voltage boost applications. The can drive a string of up
More information3A 150KHz 40V Buck DC/DC Converter With Constant Current Loop. Features. General Description. Applications
Features Wide 8V to 40V Input Voltage Range Output Adjustable from 1.25V to 37V Minimum Drop Out 0.3V Fixed 150KHz Switching Frequency Maximum 3A Switching Current Internal Optimize Power MOSFET Excellent
More informationHigh Voltage CMOS Boost White LED Driver
High Voltage CMOS Boost White LED Driver FEATURES Drives 6 to 8 White LEDs in series from 3V Up to 87% Efficiency Low Quiescent Ground Current 0.6mA Adjustable Output Current (up to 40mA) High Frequency
More informationLD7889A 3/29/ Channel LED Backlight Driver. General Description. Features. Applications. Typical Application REV: 00
3/29/2012 4-Channel LED Backlight Driver REV: 00 General Description The LD7889A is a 4-channel linear current controller which combines with a boost switching controller. It s an ideal solution for driving
More informationPin Configurations VIN 1 8 GND OUTPUT FEEDBACK GND GND ON/OFF 4 5 GND Figure2. Pin Configuration of (Top View) Table 1 Pin Description Pin Num
Features Wide 4.5V to 40V Input Voltage Range 3.3V,5V,12V, and adjustable versions Output Adjustable from 1.23V to 37V Maximum Duty Cycle 100% Minimum Drop Out 1.5V Fixed 150KHz Switching Frequency 2A
More informationLSP5504. PWM Control 2A Step-Down Converter. Applications. General Description. Features LSP5504. Typical Application Circuit
Applications Cellular Phones PC Motherboard LCD Monitor Graphic Card DVD-Video Player Telecom Equipment ADSL Modem Networking power supply Microprocessor core supply Printer and other Peripheral Equipment
More informationSPECIFICATION FOR APPROVAL
Customer Name : ( 주 ) 하이디스플레이 Date : 2011. 02. 16. SPECIFICATION FOR APPROVAL Part Name : CCFL INVERTER Customer Part No. : DS-Plus Part No. : DS-1307WK (Voltage -Dimming ) Approval Sign Please Return
More information60W Single Output Switching Power Supply
H LG-60H series Features : Universal AC input / Full range (up to 305VAC) Built-in active PFC function Protections: Short circuit / Over current / Over voltage / Over temperature Cooling by free air convection
More information4.5V to 32V Input High Current LED Driver IC For Buck or Buck-Boost Topology CN5816. Features: SHDN COMP OVP CSP CSN
4.5V to 32V Input High Current LED Driver IC For Buck or Buck-Boost Topology CN5816 General Description: The CN5816 is a current mode fixed-frequency PWM controller for high current LED applications. The
More informationLiteon Semiconductor Corporation LSP3308A 6 Channels LED Boost Driver
FEATURES Six Constant-Current Output Channels (Io=40mA each @ Vin=12V; Io=30mA each @ Vin=5V;) Parallel Channels Allow Higher Current per LED String Maximum 40V Continuous Voltage Output Limit for Each
More informationXLSEMI. Datasheet. 2A 150KHz 40V Buck DC to DC Converter. Features. General Description. Applications
Features Wide 4.5V to 40V Input Voltage Range 3.3V,5V,12V, and adjustable versions Output Adjustable from 1.23V to 37V Maximum Duty Cycle 100% Minimum Drop Out 1.5V Fixed 150KHz Switching Frequency 2A
More informationPin Configurations (TO252-5L) Figure2. Pin Configuration of (Top View) Table 1 Pin Description Pin Number Pin Name Description 1 VIN Supply Voltage In
Features Wide 4.5V to 40V Input Voltage Range 3.3V,5V,12V, and adjustable versions Output Adjustable from 1.23V to 37V Maximum Duty Cycle 100% Minimum Drop Out 1.5V Fixed 150KHz Switching Frequency 3A
More information400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter
Features Wide 3.6V to 24V Input Voltage Range Positive or Negative Output Voltage Programming with a Single Feedback Pin Current Mode Control Provides Excellent Transient Response 1.25V reference adjustable
More information