SECTION 4 TIME DELAY RELAYS 5 TO 13 AMPERES

Transcription

1 Your Contact for Relays SECTION 4 TIME DELAY RELAYS 5 TO 3 AMPERES

2 TDRPRO TIME DELAY RELAYS RELAY SERIES L.E.D. STATUS LAMP L W H..5 x.3 x 3.5 OR PIN OCTAL PLUG-IN L W H. x. x. OR PIN OCTAL PLUG-IN L W H.3 x 0.34 x. MINIATURE PLUG-IN FEATURES ON DELAY, OFF DELAY, INTERVAL AND ONE SHOT MODES AVAILABLE REPEATABILITY ±0.% FIELD ADJUSTABLE BY KNOB, OR FIXED TIME AVAILABLE WITHOUT KNOB OTHER RANGES & VOLTAGES AVAILABLE ON DELAY, REPEAT, INTERVAL, OFF DELAY & ONE SHOT UNIVERSAL POWER SUPPLY REPEATABILITY ±0.% FIELD ADJUSTABLE BY THUMB WHEELS PANEL MOUNTABLE ON DELAY REPEATABILITY ± % RECESSED SCREW ADJUSTMENT 4 POLE STYLES AVAILABLE PRINTED CIRCUIT TERMINALS AVAILABLE OTHER RANGES & VOLTAGES AVAILABLE CONTACT DATA CONTACT CONFIGURATION: DPDT SPDT, DPDT DPDT CONTACT MATERIAL: CONTACT RESISTANCE: SILVER CADMIUM OXIDE, 50 MILLIOHMS MAX. INITIAL SILVER CADMIUM OXIDE GOLD FLASHED 50 MILLIOHMS MAX. INITIAL SILVER GOLD OVERLAY, 50 MILLIOHMS MAX. INITIAL MAX. CONTACT RATING: 0 0 / 40 VAC, 30 VDC /3 HP@ 40 VAC / NEMA B300 PILOT DUTY 0 / 40 VAC, 30 VDC RESISTIVE. /3 HP@ / 40 VAC 5 VDC COIL DATA STANDARD VOLTAGE AC: DC: 4 VDC 4 TO 40 VAC 4 TO 40 VDC & 4 VDC VOLTAGE RANGE: REVERSE POLARITY PROTECTION: 5 % TO +0 % (AC) 0 % TO +0 % (DC) OF NOMINAL YES - DC NON POLARITY SENSITIVE 5 % TO +0 % (AC), 0 % TO +0 % (DC) OF NOMINAL YES - DC GENERAL DATA AMBIENT TEMPERATURE OPERATING: STORAGE: - 30 C TO +55 C - 55 C TO +5 C - 0 C TO +55 C - 40 C TO +5 C - 30 C TO +55 C - 50 C TO +5 C STANDARD RANGE: 0. SECOND TO 0 MINUTES 0. SECOND TO 9,990 HOURS 0. SECOND TO 450 SECONDS DIELECTRIC STRENGTH: 500 V RMS 500 V rms 50 V rms LIFE EXPECTANCY (MIN.) ELECTRICAL: MECHANICAL: 00,000 OPERATIONS 0,000,000 OPERATIONS 00,000 OPERATIONS 0,000,000 OPERATIONS 50,000 OPERATIONS 0,000,000 OPERATIONS AGENCY APPROVALS PAGE NUMBER 4... UL Listed File No. LISTED 3G C US File No. E434 C US File No. E434 File No. E434 PAGE - PAGE 9-0 PAGE CALL FACTORY FOR OTHER VOLTAGES, TIME AND FUNCTIONS

3 TIME DELAY RELAYS 3 EXTERNAL ADJUSTMENT 3 KNOB ADJUSTMENT 3 TRUE OFF DELAY L W H.5 x.3 x 3.5 PIN OCTAL PLUG-IN REPEAT CYCLE TIMER ON AND OFF TIMES INDEPENDENTLY ADJUSTABLE REPEATABILITY ±0.% FIELD ADJUSTABLE USING KNOBS OTHER RANGES & VOLTAGES AVAILABLE L W H.40 x.53 x.90 SQUARE BASE PLUG-IN OR FLANGE MOUNT ON DELAY, OFF DELAY REPEATABILITY ±3% FIELD ADJUSTABLE USING EXTERNAL RESISTOR L W H.53 x.40 x 3.5 SQUARE BASE PLUG-IN ON DELAY, OFF DELAY REPEATABILITY ±0.% FIELD ADJUSTABLE USING KNOB L W H.53 x.40 x 3.5 SQUARE BASE PLUG-IN TRUE OFF DELAY REPEATABILITY ±3% FIELD ADJUSTABLE USING KNOB POWER TO NOT REQUIRED DURING CYCLE DPDT DPDT DPDT DPDT SILVER CADMIUM OXIDE, SILVER CADMIUM OXIDE, SILVER CADMIUM OXIDE, SILVER CADMIUM OXIDE, 50 MILLIOHMS MAX. INITIAL 50 MILLIOHMS MAX. INITIAL 50 MILLIOHMS MAX. INITIAL 50 MILLIOHMS MAX. INITIAL 0 0 / 40VAC, 30 VDC /3 / 40 VAC, NEMA B300 PILOT DUTY VDC /3 / 40 VAC, NEMA B300 PILOT DUTY VDC /3 / 40 VAC, NEMA B300 PILOT DUTY VDC /3 / 40 VAC, NEMA B300 PILOT DUTY 4 VDC 4 VDC 4 VDC 5 % TO +0% (AC), 0 % TO +0% (DC) OF NOMINAL 5 % TO +0 % (AC) 0 % TO +0 % (DC) OF NOMINAL 5 % TO +0 % (AC) 0 % TO +0 % (DC) OF NOMINAL 5 % TO +0 % (AC) 0 % TO +0 % (DC) OF NOMINAL YES - DC YES - DC YES - DC YES - DC - 30 C TO +55 C - 55 C TO +5 C - 30 C TO +55 C - 55 C TO +5 C - 30 C TO +55 C - 55 C TO +5 C - 30 C TO +55 C - 55 C TO +5 C 0. SECOND TO 30 MINUTES 0. SECOND TO 0 SECONDS 0. SECOND TO 0 SECONDS 0. SECOND TO 00 SECONDS 500 V rms 500 V rms 000 V rms 000 V rms 00,000 OPERATIONS 0,000,000 OPERATIONS 00,000 OPERATIONS 5,000,000 OPERATIONS 00,000 OPERATIONS 5,000,000 OPERATIONS 00,000 OPERATIONS 5,000,000 OPERATIONS C US File No. E59 File No. E59 File No. E59 File No. E59 PAGE PAGE 3-4 PAGE 5 - CALL FACTORY FOR OTHER VOLTAGES, TIME AND FUNCTIONS PAGE 4...

4 TIME DELAY RELAYS RELAY SERIES 35 CURRENT SENSOR & 3 & 3 L W H.3 x.5 x 3.5 SQUARE BASE PLUG-IN L W H.50 x.3 x 3.5 SQUARE BASE PLUG-IN L W H.3 X.3 X 3. or PIN OCTAL PLUG-IN.5 TO 5 AMP SENSING RANGE -ON DELAY, -OFF DELAY 3 ON DELAY, 3 OFF DELAY ±% REPEATABILITY REPEATABILITY ±3% ± 3% REPEATABILITY FEATURES SPDT CONTACT CONFIGURATION FIELD ADJUSTABLE WITH KNOB FIELD ADJUSTABLE BY KNOB OR EXTERNAL RESISTOR FIXED VERSIONS AVAILABLE FIELD ADJUSTABLE BY KNOB OR EXTERNAL RESISTOR FIXED VERSIONS AVAILABLE 0 AMPS SWITCHING 0 AMP SWITCHING UP TO 3 POLES UP TO 3 POLES CONTACT DATA CONTACT CONFIGURATION: SPDT SPDT, DPDT, 3PDT SPDT, DPDT, 3PDT CONTACT MATERIAL: SILVER CADMIUM OXIDE, SILVER CADMIUM OXIDE, SILVER CADMIUM OXIDE, CONTACT RESISTANCE: 50 MILLIOHMS MAX. INITIAL 50 MILLIOHMS MAX. INITIAL 50 MILLIOHMS MAX. INITIAL MAX. CONTACT RATING: 0 AMPS VDC 0 0/40 VAC, VDC /3 / 40 VAC, 0 0/40 VAC, 30 VDC /3 / 40 VAC, COIL DATA STANDARD VOLTAGE AC: DC: 4 TO 40 VAC TO 5 VDC 4 TO 40 VAC TO 5 VDC VOLTAGE RANGE: REVERSE POLARITY PROTECTION: 5 % TO 0 % OF NOMINAL NOT APPLICABLE 5 % TO +0 % (AC), 0 % TO +0 % (DC) OF NOMINAL YES - DC 5 % TO +0 % (AC) 0 % TO +0 % (DC) OF NOMINAL YES - DC GENERAL DATA AMBIENT TEMPERATURE OPERATING: STORAGE: - 30 C TO +55 C - 40 C TO +5 C - 0 C TO +0 C - 55 C TO +5 C - 0 C TO +0 C - 55 C TO +5 C STANDARD RANGE:.5 TO 5 AMPS 0. SECOND TO 300 SECONDS - 0. SECOND TO 300 SECONDS - DIELECTRIC STRENGTH: 500 V rms 500 V rms 500 V rms LIFE EXPECTANCY ELECTRICAL: MECHANICAL: 00,000 OPERATIONS 5,000,000 OPERATIONS 00,000 OPERATIONS 0,000,000 OPERATIONS 00,000 OPERATIONS 0,000,000 OPERATIONS AGENCY APPROVALS PAGE NUMBER File No. E3 PAGE File No. E34 File No. E34 PAGE 9-0 PAGE - CALL FACTORY FOR OTHER VOLTAGES, TIME AND FUNCTIONS

5 TIME DELAY RELAYS 4 & 4 3 VOLTAGE SENSOR L W H. X.4 x 4.0 OR 4 PIN PLUG-IN. WITH INTEGRAL LOCKING CLIP RUGGED INDUSTRIAL DESIGN STYLE 4 - ON DELAY, STYLE 4 - OFF DELAY ±3% REPEATABILITY - 4 POLE CONTACT CONFIGURATIONS LARGE CHOICE OF OPTIONS L.E.D. STATUS LAMP L W H SEE PAGE SQUARE BASE OR OCTAL PLUG-IN INDEPENDENTLY ADJUSTABLE PICK AND DROP OUT VOLTAGES TIME DELAYED ACTION AVAILABLE ±% REPEATABILITY LED POWER INDICATOR FIELD ADJUSTABLE RECESSED POTS OR KNOBS SEE CATALOG PAGE SILVER CADMIUM OXIDE, GOLD DIFFUSED 50 MILLIOHMS MAX. INITIAL 0 0/40 VAC, VDC 4 TO 40 VAC TO 50 VDC 5 % TO +0 % (AC), 0 % TO +0 % (DC) OF NOMINAL YES - DC SPDT, DPDT SILVER CADMIUM OXIDE, 50 MILLIOHMS MAX. INITIAL SPST:3 0/40 VAC, VDC /3 HP@, / 40 / 40 VAC 3 40 VAC.NEMA B300 PILOT DUTY DPDT:0 0 / 40 VAC, VDC /3 HP@, / 40 VAC NEMA B300 PILOT DUTY 4 TO 40 VAC 4 VDC - YES - DC Your Contact for Relays U. S. A. TELEPHONE: (43) FAX: (43) WEBSITE: info@magnecraft.com EUROPE TELEPHONE: 499 / FAX: 499 / WEBSITE: renatesteinback@magnecraft.de - 0 C to +55 C - 55 C to +0 C 0. SECOND TO 300 SECONDS V rms - 30 C to +55 C - 40 C to +5 C SEE CATALOG PAGE 500 V rms 00,000 OPERATIONS 0,000,000 OPERATIONS 00,000 OPERATIONS 0,000,000 OPERATIONS (DPDT) File No. E34 LISTED 3G UL Listed With Magnecraft Socket 4 SERIES File No. E3 PAGE 3-4 PAGE 5 - CALL FACTORY FOR OTHER VOLTAGES, TIME AND FUNCTIONS 4...4

6 APPLICATION DATA WHAT IS A TIME DELAY RELAY: A Time Delay relay is a combination of an electromechanical output relay and a control circuit. The control circuit is comprised of solid state components and timing circuits that control operation of the relay and timing range. Typical time delay functions include On-Delay, Off-Delay, Repeat cycle, One Shot, Interval, On-Delay & Off Delay (Combination) and True Off Delay. Each function is explained below. Time delay relays have a broad choice of timing ranges from less than one second to hours. There is a choice of timing adjustments from calibrated external knob, recessed pots or internally fixed timing. The output contacts on the electromechanical output relay are direct wired to the output terminals. The contact load ratings are specified for each specific type of time delay relay. FUNCTIONS: ON-DELAY- (SLOW OPERATE RELAY) Upon application of power to the input, the time delay period begins. At the end of the time delay period, output contacts transfer. Input power must be removed to return output contacts to home position and reset the control circuit. If input power is interrupted before a timing period ends, timing stops. When input power is restored, timing starts from the beginning. POWER OUTPUT DELAY ON OFF TRANSFERRED HOME Some typical Applications: Cascade starting, Air Conditioning & heating controls, Burglar Alarms, Power Outage delay, instrument Control. DESCRIPTIONS OF TIME DELAY FUNCTIONS OFF-DELAY (SLOW RELEASE RELAY) Continuous power must be applied to input during all timing sequences. Upon closure of external control switch, output contacts transfer. Upon opening control switch, the timing period begins. When timing period ends, output contacts return home. To repeat this timing cycle, the control switch must be re-closed and then opened. If input power is interrupted during timing cycle, the output contacts return to home position and the control switch must be closed and reopened to start the timing from the beginning. If the control switch closes during a timing period, timing stops and output contacts remain transferred. When control switch is opened, timing will start again from the beginning. The timing period can be extended, repeatedly using the control switch in this way until the last initiated timing period is permitted to end and output contacts return home. POWER CONTROL SWITCH OUTPUT DELAY Some typical Applications: Air Conditioning, automatic Door Controls, Lighting Controls, burglar alarms, Vending Machines, circuits, conveyor systems, instrument control, watchdog circuits. REPEAT CYCLE (FLASHER) DELAY ON OFF CLOSED OPEN DELAY TRANSFERRED HOME Upon application of power to the input, the Off time delay Period begins. The contacts transfer at the end of the Off time Delay Period and the ON time delay period begins. At the end of the ON time delay period output contacts return home and OFF time delay period begins again. This sequence will continue as long as input power is supplied to the Input Pins. POWER OUTPUT ON OFF OFF ON ON OFF TRANSFERRED HOME Some typical Applications: Signs, Product testing, signal devices, machine control, Signal warning devices, conveyor control.

7 DESCRIPTIONS OF TIME DELAY FUNCTIONS APPLICATION DATA ONE SHOT (RETRIGGERABLE) ON-DELAY & OFF-DELAY- (COMBINATION) Continuous power must be applied to the input during all timing sequences. Upon closure of external control switch, output contacts transfer and timing period begins. When timing period ends, output contacts return home. Once the timing period begins, the control switch may remain closed or opened without affecting timing. To repeat this cycle, the control switch must be open, or opened at the end of the timing period, and then closed to start timing period over again. POWER ON OFF Continuous power must be applied to the input during all timing sequences. Upon closure of the external control switch, first time delay period T begins. When T period ends, output contacts transfer. Then, when control switch is opened, second delay period T begins. When T ends, output contacts return home. To repeat this timing cycle, repeat this sequence from the beginning. If the prevailing open or closed status of the control switch is changed during either T or T Timing periods, timing stops. Position of output contacts remain as they were. Returning control switch to its pre-changed position restarts interrupted timing period from the beginning and normal timing resumes. CONTROL SWITCH OUTPUT Some typical Applications: Vending machines, dispensing controls, machine control, welding control, INTERVAL DELAY DELAY CLOSED OPEN TRANSFERRED HOME POWER CONTROL SWITCH OUTPUT CONTROL SWITCH OUTPUT T T Interrupted T T T ON OFF CLOSED OPEN TRANSFERRED HOME Interrupted CLOSED OPEN T TRANSFERRED HOME Upon application of power to the input, the output contacts transfer and the delay period begins. At the end of the time delay period, the output contacts return home. Input power must be interrupted to recycle timer. Some typical Applications: Cascade starting & stopping of heavy loads, laboratory equipment, machine control TRUE OFF DELAY- (SLOW RELEASE) POWER OUTPUT DELAY ON OFF TRANSFERRED HOME Upon application of power to the input, output contacts transfer. The delay period begins when power is removed from the input. If power is supplied to input during the timing period, time is reset and time delay period starts over again when power is removed from the input. Some typical Applications: Machine control, End of process alarm, Welding control, Photographic timing. POWER ON OFF OUTPUT DELAY TRANSFERRED HOME Some typical Applications: Loss of power alarm control, Burglar alarms. U. S. A. TELEPHONE: (43)393-5 FAX: (43) WEBSITE: info@magnecraft.com EUROPE TELEPHONE: 499 / FAX: 499/ WEBSITE: renatesteinback@magnecraft.de 4...

8 OCTAL & PIN TIME DELAY RELAY DPDT, 0 AMPS THE CLASS TIME DELAY RELAY MAKES USE OF HYBRID CIRCUITRY, COMBINING INTEGRATED CIRCUITS FOR A MULTITUDE OF FUNCTIONS, AND THE RELIABILITY OF RELAY TECHNOLOGY. GENERAL SPECIFICATIONS c LISTED 3G WHEN USED WITH SOCKETS ( PIN) ( PIN) us File No. E434 COMPLIES WITH REQUIREMENTS OF IEC STANDARDS AND LOW VOLTAGE DIRECTIVE IEC = INTERNATIONAL ELECTROTECHNICAL COMMISSION CE TESTING AND EVALUATION PERFORMED BY THE UNDERWRITERS LABORATORIES AS A THIRD PARTY PARTICIPANT Operating Modes Available: Timing Adjustments Available: Repeatability (Repeat Accuracy when Stabilized): Timing Change Over Temperature and Voltage Range: Timing Tolerance High End: Timing Tolerance Low End : Reset Time: Contact Rating: Contact Life: Mechanical Life: Operating Voltage Range: Temperature range (Operate): Temperature range (Storage): Steady State Input Current: PROTECTION Reverse Polarity: Transient: Noise Immunity: DIELECTRIC STRENGTH Coil to Contacts: Across Open Contacts: On delay, off delay, Interval, one shot 0. to 0 minutes ±0.% max. or ±33 ms AC min. or± 0 ms DC. constant voltage & temperature ± 0% - 0 to + 40% + 0 to - 40% 00 milliseconds max. 0 0VAC / 30VDC resistive load, / 40 VAC, /3 NEMA B300 pilot duty 00,000 0VAC, 0 amps resistive load,000,000 5 amps resistive load,000,000 0VAC, amps resistive load 0,000,000 operations AC: 5 % to 0 %, DC: 0 % to 0 % of nominal - 30 C to + 55 C - 55 C to + 5 C 0 4 VAC, VAC, 0 VDC, 50 VDC, 30 4 VDC Yes - DC UL 50 surge test: 5000V for 50 us NEMA ICS VAC 500 V rms 000 V rms MECHANICAL Operating Position: Enclosure: Mounting: Weight: Any Polycarbonate dust cover Standard or pin octal 5 grams approx Mating Sockets 0-50D-, 0-50D-, 0-44-, 0-45-: SCREW/DIN 0-9-, 0-0-: SCREW/PANEL See section, page PHONE: (43) FAX: (43) info@magnecraft.com

9 OCTAL & PIN TIME DELAY RELAY OUTLINE DIMENSIONS DIMENSIONS SHOWN IN INCHES & (MILLIMETERS). DPDT, 0 AMPS 0.5 (4.).93 (4.4) WIRING DIAGRAMS.3 (0.3) (44.4) ON-DELAY + - ON DELAY EXTERNALCONTROL SWITCH PIN OCTAL EXTERNAL SWITCH SHALL NOT BE 3 9 CONNECTED TO ANY EXTERNAL LOAD 0 OR VOLTAGE. DAMAGE TO INTERNAL.5 OFF-DELAY COMPONENTS CAN OCCUR. (44.4) OFF DELAY + - PIN OCTAL STANDARD PART NUMBERS NOMINAL VOLTAGE RANGE CALL FACTORY FOR OTHER VOLTAGES, TIME AND FUNCTIONS ON DELAY WACPSOX- WACPSOX-5 WACPSOX- WACPSOX- WACPSOX-0 WACPSOX- WACPSOX- WACPSOX-3 WCPSOX- WCPSOX-3 OFF DELAY WACPSRX-5 WACPSRX- WACPSRX- WACPSRX-0 WCPSRX- WCPSRX-3 4 VDC 4 VDC 4 VDC 4 VDC 0. TO.0 SECONDS 0. TO 0 SECONDS.0 TO 0 SECONDS.0 TO 300 SECONDS.0 TO 5 MINUTES.0 TO 30 MINUTES 4.0 TO 0 MINUTES.0 TO 0 MINUTES 0. TO 0 SECONDS.0 TO 0 SECONDS 0. TO 0 SECONDS.0 TO 0 SECONDS.0 TO 300 SECONDS.0 TO 5 MINUTES 0. TO 0 SECONDS.0 TO 0 SECONDS 4...

10 TDRPRO- FEATURES 5 FUNCTIONS, RANGES FROM 0. SECONDS TO 9,990 HOURS, UNIVERSAL VOLTAGE AND AMP OUTPUT FOR HIGHER POWER APPLICATIONS PROGRAMMABLE TIME DELAY RELAY BENEFITS FIVE FUNCTIONS - ONE PACKAGE SPDT & DPDT, AMPS c us File No. E434 UNIVERSAL POWER SUPPLY ALLOWS FOR VOLTAGES FROM 4 TO 40 VDC OR VAC 50/0HZ. CLASS F INSULATION SYSTEM THUMB WHEEL ADJUSTMENTS FOR FUNCTION AND RED L.E.D. LAMP INDICATOR 0. % ACCURACY USING A CRYSTAL CLOCK MOUNTING CLIP ALLOWS FOR VARIED PANEL THICKNESSES, ONE PART FOR MOST VOLTAGES AMPS CONTACT RATING POSITIVE POSITION THUMB WHEEL ADJUSTMENT STATUS L.E.D. ACCURATE TIME, ALL THE TIME PANEL CLIP INCLUDED PENDING COMPLIES WITH REQUIREMENTS OF IEC STANDARDS AND LOW VOLTAGE DIRECTIVE IEC = INTERNATIONAL ELECTROTECHNICAL COMMISSION CE TESTING AND EVALUATION PERFORMED BY THE UNDERWRITERS LABORATORIES AS A THIRD PARTY PARTICIPANT MANUFACTURED UNDER ISO 900 & QS 9000 GENERAL SPECIFICATIONS Operating Modes Available: On delay, repeat, one shot, off delay & interval Timing Adjustments: 0. second to 9,990 hours Repeatability: 0.%, (Internal crystal) (Constant Voltage and Temperature) Contact Material: Contact Rating: Voltage Range: Temperature Range (Operate): Temperature Range (Storage): Transient Protection: Reverse Polarity Protection: DIELECTRIC STRENGTH Between Output Poles: Between Input and Output: LIFE EXPECTANCY Electrical: Mechanical: MISCELLANEOUS Operating Position: Enclosure: Mounting: Weight: Silver cadmium oxide, gold flashed 0 / 40 VAC, 30 VDC resistive /3 / 40 VAC 4 to 40 VDC / VAC ± 5%, 50/0 Hz. -0 C to +55 C -40 C to +5 C Yes Non polarity sensitive,500 V rms,500 V rms 00,000 operations 0,000,000 operations Any Gray polycarbonate pin octal plug-in, pin octal. x. (45 x 45) panel cutout. grams approx. PHONE: (43) FAX: (43) info@magnecraft.com Mating Sockets 0-50D-, 0-50D-, 0-44-, 0-45-: SCREW/DIN 0-9-, 0-0-: SCREW/PANEL See section, page -

11 TDRPRO- PROGRAMMABLE TIME DELAY RELAY 5 FUNCTION. (4.49) RED L.E.D. LAMP INDICATOR OUTLINE DIMENSIONS DIMENSIONS SHOWN IN INCHES & (MILLIMETERS)..3 MAX. (.9) 0.4 (.3) SPDT & DPDT, AMPS. (44.) Magnecraft Struthers-Dunn A - ON DELAY B - REPEAT C - INTERVAL D - OFF DELAY E - ONE SHOT TIME SET TDRPRO-5000 B 0 0 S TIME BASE. (4.49). (44.) POSITIVE POSITION THUMB WHEEL ADJUSTMENTS 3.5 MAX. (0.0) PIN OCTAL BASE 3 FUNCTION Magnecraft Struthers-Dunn A - ON DELAY B - REPEAT C - INTERVAL TDRPRO-500 TIME SET TIME BASE. (4.49) PANEL CUTOUT FOR PANEL MOUNTING.0 (45.) A 0 0 S.0 (45.) WIRING DIAGRAMS VIEWED FROM PIN END EXTERNAL CONTROL SWITCH EXTERNAL CONTROL SWITCH EXTERNAL CONTROL SWITCH TDRPRO-500 TDRPRO-500 TDRPRO EXTERNAL SWITCH SHALL NOT BE CONNECTED TO ANY EXTERNAL LOAD OR VOLTAGE. DAMAGE TO INTERNAL COMPONENTS CAN OCCUR. STANDARD PART NUMBERS 5 FUNCTION - PIN TDRPRO FUNCTION - PIN TDRPRO FUNCTION - PIN TDRPRO-500 NOMINAL VOLTAGE 4-40 VAC 4-40 VDC 4-40 VAC 4-40 VDC 4-40 VAC 4-40 VDC RANGE 0. SECOND TO 9,990 HOURS 0. SECOND TO 9,990 HOURS 0. SECOND TO 9,990 HOURS 4...0

12 MINIATURE TIME DELAY RELAY OUTLINE DIMENSIONS DIMENSIONS SHOWN IN INCHES & (MILLIMETERS). DPDT, 5 AMPS 0.34 (.) (0.) 0.45 (.) File No. E434 RECESSED SCREW ADJUSTMENT. MAX. (30.) 0.00 (5.) 0.0 (.) CHASSIS CUTOUT FOR PANEL MOUNTING 0.5 (4.) 0.90 (9).3 (34.9) 0. (4.3) 0.35 (.9) 0.5 (.) 3-4 UNC THREAD 0.34 (.) (.3) 0.40 (3.5) 0.09 DIA (.) GENERAL SPECIFICATIONS Operating Modes Available: Timing Adjustments Available: Repeatability (Repeat Accuracy when Stabilized): Reset time: On delay, 0. to 450 seconds ± % nominal 5 C 00 milliseconds max. Contact Rating: Contact Life: Mechanical Life: 5 0VAC / VDC resistive 50,000 5 amps resistive,500,000 amps resistive load,000,000 amp resistive load 0,000,000 operations WIRING DIAGRAM Operating Voltage Range: Temperature Range (Operate): Temperature Range (Storage): Steady State Input Current: AC: 5 % to 0 %, DC: 0 % to 0 % of nominal -30 C to + 55 C -50 C to +5 C 40 4 VDC, 0 VDC PROTECTION Reverse Polarity: Transient: DIELECTRIC STRENGTH Coil to Contacts: Across Open Contacts: MECHANICAL Operating Position: Enclosure: Mounting: 4... Weight: Yes - DC Twice nominal voltage for millisecond 500 V rms 50 V rms Any Polycarbonate dust cover Socket plug-in/solder also available with printed circuit terminals 35. grams approx CALL FACTORY FOR OTHER VOLTAGES, TIME AND FUNCTIONS STANDARD PART NUMBERS ON DELAY WCPSOX- WCPSOX- NOMINAL VOLTAGE VDC 4 VDC Chassis Mount Socket: PCB Socket: See section, page 5. RANGE 0. TO 30 SECONDS 0. TO 30 SECONDS 4PDT AVAILABLE

13 OUTLINE DIMENSIONS DIMENSIONS SHOWN IN INCHES & (MILLIMETERS). OCTAL PIN REPEAT CYCLE TIMER RELAY DPDT, 5 AMPS 0.5 (4.).93 (4.4).5 (44.4) File No. E434.3 (0.35) PIN OCTAL INDEPENDENT TIME SETTINGS FOR BOTH ON AND OFF RANGES COMPLIES WITH REQUIREMENTS OF IEC STANDARDS AND LOW VOLTAGE DIRECTIVE IEC = INTERNATIONAL ELECTROTECHNICAL COMMISSION CE TESTING AND EVALUATION PERFORMED BY THE UNDERWRITERS LABORATORIES AS A THIRD PARTY PARTICIPANT GENERAL SPECIFICATIONS Operating Modes Available: Timing Adjustments Available: Repeatability (Repeat Accuracy when Stabilized): Timing change over temperature and voltage range: Timing Tolerance high end of range: Timing Tolerance low end of range: Reset time: Contact Rating: Contact Life: Mechanical Life: Repeat cycle timing 0. to 30 minutes ±0.% Max. or ± 33 ms AC min. or ± 0 ms DC. constant voltage & temperature ± 0% - 0 to + 40% + 0 to - 40% 00 milliseconds max. 0 0 / 40 VAC, 30 VDC resistive load, / 40 VAC, /3 NEMA B300 pilot duty 00,000 0VAC, 0Amp resistive load,000,000 5 Amp resistive load,000,000 0VAC, Amps resistive load 0,000,000 operations WIRING DIAGRAM Operating Voltage Range: Temperature Range (Operate): Temperature Range (Storage): Steady State Input Current: PROTECTION Reverse Polarity: Transient: Noise Immunity: DIELECTRIC STRENGTH Coil to Contacts: Across Open Contacts: MECHANICAL Operating Position: Enclosure: Mounting: Weight: AC: 5% to 0%, DC: 0% to 0% of nominal -30 C to +55 C -55 C to +5 C VAC, 0 VDC, 40 4 VDC, 4 4 VDC. Yes - DC UL 50 saurge test: 5000V for 50 us NEMA ICS VAC 500 V rms 000 V rms Any Polycarbonate dust cover pin octal 3 grams approx. CALL FACTORY FOR OTHER VOLTAGES, TIME AND FUNCTIONS STANDARD PART NUMBERS REPEAT CYCLE WACPFX- WACPFX- WACPFX- NOMINAL VOLTAGE Mating Sockets 0-50D-, 0-50D-, 0-44-, 0-45-: SCREW/DIN 0-9-, 0-0-: SCREW/PANEL See section, page - RANGE 0. TO 0 SECONDS 3 TO 300 SECONDS TO 30 MINUTES 4...

14 3 SQUARE BASE TIME DELAY RELAYS DPDT, AMPS "ON" OR "OFF" DELAY FUNCTIONS EXTERNAL RESISTANCE ADJUSTABLE ± 3 % REPEATABILITY DPDT, AMP File No. E59 COMPLIES WITH REQUIREMENTS OF IEC STANDARDS AND LOW VOLTAGE DIRECTIVE IEC = INTERNATIONAL ELECTROTECHNICAL COMMISSION CE TESTING AND EVALUATION PERFORMED BY THE UNDERWRITERS LABORATORIES AS A THIRD PARTY PARTICIPANT GENERAL SPECIFICATIONS Operating Modes Available: Timing Adjustments Available: Repeatability: Percent Timing Change Over Temperature and Voltage Range: Timing Tolerance High End : Timing Tolerance Low End: On delay, off delay 0. to 0 seconds nominal 5 C ±0% -0 to +40% +0 to -40% Contact Rating: Contact Life: Mechanical Life: Operating Voltage Range: Temperature Range (Operate): Temperature Range (Storage): Steady State Input Current: PROTECTION Reverse Polarity: Transient: / VDC resistive /3 HP,, / HP, 40 VAC B300 pilot duty. 00,000 amps resistive load.,000,000 VDC 5 amps resistive load. 5,000,000 operations AC: 5% to 0%, DC: 0% to 0% of nominal - 30 C to + 55 C - 55 C to + 5 C VDC Yes - DC Twice nominal voltage for millisecond DIELECTRIC STRENGTH Coil to Contacts: Across Open Contacts: MECHANICAL Operating Position: Enclosure: Terminals: Weight: 500 V rms 000 V rms Any Polycarbonate dust cover 0. x 0.00 quick connect terminals 9 grams approx. Mating Sockets 0-43-: SCREW/DIN 0-4-: SOLDER 0--, 0--: PRINTED CIRCUIT 0-4-: QUICK CONNECT See section, page, PHONE: (43) FAX: (43) info@magnecraft.com

15 3 SQUARE BASE TIME DELAY RELAYS OUTLINE DIMENSIONS DIMENSIONS SHOWN IN INCHES & (MILLIMETERS). DPDT, AMPS SOLDER / PLUG-IN TERMINALS 0. X 0.00 (4.4 X 0.50) QUICK CONNECT TERMINALS.53 MAX. (3.) 0.5 (3.9).50 MAX. (3.5).90 MAX. (3.) WIRING DIAGRAMS EXTERNAL RESISTOR.90 MAX. (4.4) 0.00 (0.50).40 (35.5) 4 A.53 MAX. (3.) B 4 A B THE PLUG-IN STYLE TIMER HAS THE SAME CASE DIMENSIONS AS THE FLANGE MOUNT STYLE EXCEPT IT HAS NO FLANGE AND IT IS ALSO SOCKET MOUNTABLE. ON DELAY EXTERNAL RESISTOR EXTERNAL SWITCH SHALL NOT BE CONNECTED TO ANY EXTERNAL LOAD OR VOLTAGE. DAMAGE TO INTERNAL COMPONENTS CAN OCCUR. A B OFF DELAY EXTERNAL CONTROL SWITCH STANDARD PART NUMBERS NOMINAL VOLTAGE RANGE EXTERNAL RESISTOR ON DELAY PLUG-IN STYLE W3ACPSOX- W3ACPSOX- W3CPSOX- W3CPSOX- W3ACQSOX- W3ACQSOX- W3CQSOX- 4 VDC 4 VDC ON DELAY SURFACE MOUNT FLANGE STYLE 4 VDC OFF DELAY PLUG-IN STYLE W3CPSRX- 4 VDC CALL FACTORY FOR OTHER VOLTAGES, TIME AND FUNCTIONS 0. TO 0 SECONDS.0 TO 0 SECONDS 0. TO 0 SECONDS.0 TO 0 SECONDS 0. TO 0 SECONDS.0 TO 0 SECONDS.0 TO 0 SECONDS.0 TO 0 SECONDS 0,000 Ω PER SECOND,000 Ω PER SECOND 0,000 Ω PER SECOND,000 Ω PER SECOND 4...4

16 3 SQUARE BASE TIME DELAY RELAY DPDT, AMPS THE CLASS 3 IS KNOB ADJUSTABLE "ON" OR "OFF" DELAY FUNCTIONS. DPDT, AMP, ± 0. % REPEATABILITY, File No. E434 GENERAL SPECIFICATIONS COMPLIES WITH REQUIREMENTS OF IEC STANDARDS AND LOW VOLTAGE DIRECTIVE IEC = INTERNATIONAL ELECTROTECHNICAL COMMISSION CE TESTING AND EVALUATION PERFORMED BY THE UNDERWRITERS LABORATORIES AS A THIRD PARTY PARTICIPANT Operating Modes Available: Timing Adjustments Available: Repeatability: Timing Change Over Temperature and Voltage Range: Timing Tolerance High End: Timing Tolerance Low End: Reset Time: Contact Rating: Contact Life: Mechanical Life: Operating Voltage Range: Temperature Range (Operate): Temperature Range (Storage): Steady State Input Current: PROTECTION Reverse Polarity: Transient: Noise Immunity: DIELECTRIC STRENGTH Coil to Contacts: Across Open Contacts: MECHANICAL Mounting Position: Enclosure: Terminals: Weight: On delay, off delay 0. to 30 minutes ±0.% ±33 ms AC min. or ± 0 ms constant voltage & temperature ±0% -0 to +40% +0 to -40% 00 ms max. / VDC resistive /3 Hp,, / Hp, 40 VAC NEMA B300 pilot duty 00,000 amps resistive load,000,000 5 amps resistive load,000,000 amps resistive load 5,000,000 operations AC: 5% to 0%, DC: 0% to 0% of nominal - 30 C to + 55 C - 55 C to + 5 C 5 30 VAC, VAC, 0 4 VDC, 0 4 VDC, 0 VDC Yes - DC UL 50 Surge test: 5000V for 50 us NEMA ICS-30: 500 VAC 000 V rms 000 V rms Any Polycarbonate dust cover 0. x 0.00 quick connect terminals 9 grams approx. PHONE: (43) FAX: (43) info@magnecraft.com Mating Sockets 0-43-: SCREW/DIN 0-4-: SOLDER 0--, 0--: PRINTED CIRCUIT 0-4-: QUICK CONNECT See section, page,

17 3 SQUARE BASE TIME DELAY RELAY DPDT, AMPS OUTLINE DIMENSIONS DIMENSIONS SHOWN IN INCHES & (MILLIMETERS). 0.5 (5.) 0.3 (.9).40 (35.).53 (3.) A B.90 MAX. (3.) 0. x 0.00 (4.4 x 0.50) QUICK CONNECT TERMINALS WIRING DIAGRAMS A 9 B ON DELAY EXTERNAL SWITCH SHALL NOT BE CONNECTED TO ANY EXTERNAL LOAD OR VOLTAGE. DAMAGE TO INTERNAL COMPONENTS CAN OCCUR. A EXTERNAL CONTROL SWITCH OFF DELAY B STANDARD PART NUMBERS ON DELAY W3ACPSOX-4 W3ACPSOX-44 OFF DELAY W3CPSRX- W3CPSRX-4 CALL FACTORY FOR OTHER VOLTAGES, TIME AND FUNCTIONS NOMINAL VOLTAGE 4 VDC 4 VDC RANGE 0. TO 0 SECONDS.0 TO 0 SECONDS 0. TO 0 SECONDS.0 TO 0 SECONDS 4...

18 0.5 (5.) 3 OUTLINE DIMENSIONS DIMENSIONS SHOWN IN INCHES & (MILLIMETERS)..90 MAX. (3.) 0. X 0.00 (4.4 X 0.50) QUICK CONNECT TERMINALS GENERAL SPECIFICATIONS Operating Modes Available: Timing Adjustments Available: Repeatability (Repeat Accuracy when Stabilized): Reset Time: 0.3 (.9).40 (35.) True off delay 0. to 5 Minutes.53 (3.) File No. E434 A B THE CLASS 3 ADJUSTABLE TRUE OFF DELAY RELAY COMBINES A SOLID STATE CIRCUIT WITH A STATE OF THE ART MAGNETIC LATCHING RELAY. THIS COMBINATION ALLOWS THE RELAY TO PULL-IN WHEN POWER IS APPLIED TO THE. STARTS WHEN POWER IS REMOVED FROM THE AND AT THE END OF THE PRESET PERIOD THE RELAY WILL DROPOUT. nominal voltage & 5 C 00 ms max. TRUE OFF TIME DELAY RELAY DPDT, AMPS COMPLIES WITH REQUIREMENTS OF IEC STANDARDS AND LOW VOLTAGE DIRECTIVE IEC = INTERNATIONAL ELECTROTECHNICAL COMMISSION CE TESTING AND EVALUATION PERFORMED BY THE UNDERWRITERS LABORATORIES AS A THIRD PARTY PARTICIPANT Contact Rating: Contact Life: Mechanical Life: Temperature Range Operate: Temperature Range Storage: Input Current: / VDC resistive /3 Hp,, / Hp, 40 VAC NEMA B300 pilot duty 00,000 amps resistive load,000,000 5 amps resistive load,000,000 amps resistive load 5,000,000 operations - 0 C to + 55 C - 40 C to + 5 C 0 0VAC, 5 4VDC WIRING DIAGRAM A B + - PROTECTION Reverse Polarity: Transient: DIELECTRIC STRENGTH Coil to Contacts: Across Open Contacts: Yes - DC 000 VAC for 50 microseconds 000 V rms 000 V rms STANDARD PART NUMBERS Mating Sockets 0-43-: SCREW/DIN 0-4-: SOLDER 0--, 0--: PRINTED CIRCUIT 0-4-: QUICK CONNECT See section, page, NOMINAL VOLTAGE RANGE MECHANICAL Enclosure: Mounting: Terminals: Weight: 4... Polycarbonate dust cover Square base plug-in 0." X 0.00" quick connect terminals 9 grams approx. PHONE: (43) FAX: (43) info@magnecraft.com AC OPERATED W3ACPSRX-9 W3ACPSRX-30 DC OPERATED W3CPSRX-35 W3CPSRX-3 4 VDC 4 VDC 0. TO 0 SECONDS 0. TO 0 SECONDS 0. TO 0 SECONDS 0. TO 0 SECONDS

19 35 CURRENT SENSING RELAY OUTLINE DIMENSIONS DIMENSIONS SHOWN IN INCHES & (MILLIMETERS). SPDT,.5 TO 5 AMPS 0.5 (5.).90 MAX. (3.) 0.3 (.9).53 (3.) File No. E3.40 (35.) A B.3(33.3) ANTI-ROTATION TAB (/4 TERMINAL STYLE) 0.5 (.) CLASS 35 CURRENT SENSING RELAY COMBINES A SOLID STATE SENSOR WITH A SPDT, 0 AMPS RELAY. THE SENSOR IS FIELD ADJUSTABLE FOR DETECTING AC CURRENT LEVELS IN EQUIPMENT. -3 TAPPED HOLE (/4 TERMINAL STYLE) GENERAL SPECIFICATIONS CURRENT SENSING: Sense Current Range: Repeatability: Contact Rating: Transient: Contact Life: Mechanical Life: Input Current: Current Sensor Resistance: Temperature Range Operate: Temperature Range Storage:.5 to 5 amps constant voltage & temperature ±0% over voltage & temperature range 0 VDC 000 V rms for 5 microseconds 00,000 rated load 5,000,000 no load 5 ma (. VA) 5 milliohms -0 C to +55 C -40 C to +5 C SUPPLY VOLTAGE WIRING DIAGRAM 4 A 3 5 CONTINUOUS VOLTAGE MUST BE SUPPLIED TO. 9 LOAD B DIELECTRIC STRENGTH Coil to Contacts: Across Open Contacts: MECHANICAL Enclosure: Terminals: Mounting: Mounting Bracket: Weight: 500 V rms 500 V rms Polycarbonate dust cover 0. or 0.50 quick connect terminals Square base plug-in Optional 3 grams approx. STANDARD PART NUMBERS W35ACX- W35ACX-3 Mating Sockets 0-43-: SCREW/DIN 0-4-: SOLDER 0--, 0--: PRINTED CIRCUIT 0-4-: QUICK CONNECT See section, page, NOMINAL VOLTAGE CURRENT RANGE.5 TO 5 AMPS.5 TO 5 AMPS TERMINAL SIZE CALL FACTORY FOR OTHER VOLTAGES, TIME AND FUNCTIONS 4...

20 & SQUARE BASE TIME DELAY RELAYS SPST, DPDT & 3PDT, 0 AMPS THE CLASS ON DELAY & OFF DELAY TIME DELAY RELAYS HAVE RANGES FROM 0. TO 300 SECONDS. THE TIMER HAS UP TO THREE POLES AND THE TIMER HAS UP TO TWO POLES. THE & TIME DELAY RELAYS ARE RATED AT 0 AMPS, 0/40 VAC, VDC. File No. E34 GENERAL SPECIFICATIONS Operating Modes Available: Timing Adjustments Available: Repeatability (Repeat Accuracy when Stabilized): Reset time: On delay, off delay, Interval 0. to 300 minutes ± 0 C to 5 C (AC + ms) 50 ms max. Contact Material: Contact Rating: Contact Life: Mechanical Life: Operating Voltage Range: Temperature Range (Operate): Max. Allowed Voltage: PROTECTION Reverse Polarity: Transient: DIELECTRIC STRENGTH Coil to Contacts: Across Open Contacts: MECHANICAL Operating Position: Enclosure: Weight: Silver cadmium oxide. 0 0 / 40 VAC 0 VDC /3 / 40 VAC 00,000 rated load 0,000,000 no load AC: 5%, DC: 0% of nominal 0 C to +0 C 0% of nominal voltage Yes - DC 000 V for 5 ms 500 V rms 500 V rms Any Clear polycarbonate 4 grams approx. PHONE: (43) FAX: (43) info@magnecraft.com Mating Sockets 0-43-: SCREW/DIN 0-4-: SOLDER 0--, 0--: PRINTED CIRCUIT 0-4-: QUICK CONNECT See section, page,

21 & SQUARE BASE TIME DELAY RELAYS ORDERING CODE FOR RELAYS, & 3 POLE, 0 AMPS XAX C 00 F 0A OUTLINE DIMENSIONS DIMENSIONS SHOWN IN INCHES & (MILLIMETERS). CLASS: : ON DELAY : OFF DELAY CONTACT ARRANGEMENTS: XAX: SPDT XBX: DPDT XCX: 3PDT ( ONLY) 0.5 (5.).90 MAX. (3.) 0. TYP. (.4).35 MAX. (34.9) A B MOUNTING OPTIONS: C: PLUG-IN C NOTE : BRACKET CS NOTE : TOP STUD C: SIDE TAPPED HOLE CS: SIDE STUD 0. x 0.00 (4.4 x 0.50) QUICK CONNECT TERMINALS CODE C RANGES: SEC: CODE SEC: CODE SEC: CODE SEC: CODE SEC: CODE 00-0 SEC: CODE SEC: CODE 300 ADJUSTMENT OPTIONS ADJUSTMENT KNOB): NO CODE FIXED DELAY: SPECIFY FIXED TIME & CODE F REMOTE ADJUSTMENT: CODE R OPERATING VOLTAGE: 4, 4, 0, 40 ADD "A" FOR AC COILS, 4, 4, 5-5 ADD "D" FOR DC COILS (F Models) - timing code does not apply. Specify single delay time requirement (R Models)- Available only for SPDT and DPDT models. External potentiometer required. Example of typical fixed time delay relay part number- XBXCS-3.5F-0A (ON DELAY, DPDT, TOP STUD, 3.5 SEC FIXED, COIL ) NOTE : BRACKET & TOP STUD NOT AVAILABLE WITH ADJUSTABLE..50 MAX. (3.) WIRING DIAGRAM EXTERNAL RESISTOR 4 EXTERNAL SWITCH MODEL ONLY EXTERNAL RESISTOR A 9 B XAX (SPDT) XAX (SPDT) A B XCX (3PDT) A B EXTERNAL SWITCH MODELONLY XBX (DPDT) XBX (DPDT) 4...0

22 3 & 3 OCTAL & PIN TIME DELAY RELAYS ORDERING CODE FOR RELAYS SPDT, DPDT & 3PDT 0 AMPS 3 XAX 4P 00 F 0A CLASS: 3: ON DELAY 3: OFF DELAY File No. E34 CONTACT ARRANGEMENTS: XAX: SPDT XBX: DPDT XCX: 3PDT CONSTRUCTION STYLE: OCTAL STYLE PLUG-IN: CODE 4P NON STANDARD WIRING: CODE 4P-K RANGES: SEC: CODE SEC: CODE SEC: CODE SEC: CODE SEC: CODE 00-0 SEC: CODE SEC: CODE 300 ADJUSTMENT: ADJUSTMENT KNOB): NO CODE FIXED DELAY: SPECIFY FIXED TIME & CODE F REMOTE ADJUSTMENT: CODE R OPERATING VOLTAGE: 4, 4, 0, 40 ADD "A" FOR AC COILS, 4, 4, 5-5 ADD "D" FOR DC COILS F Models) - timing code does not apply. Specify single delay time requirement (R Models)- Available only for SPDT and DPDT models. External fixed or Adjustable resistor required. Example of typical fixed time delay relay part number - 3XBX4P3.5F-0A (ON DELAY, DPDT, OCTAL PLUG, 3.5 SEC FIXED, POWER ) GENERAL SPECIFICATIONS Repeatability: Accuracy: Switching Time of Output Relay: Min. Waiting Time Before Starting Next Cycle (Reset Time): Contact Material: Rating: Electrical Life: Mechanical Life: Nominal Voltage: Minimum Oper. Voltage: Max. Allowed Voltage: Ambient Temperature Rating: DIELECTRIC STRENGTH Across Open Contacts: Coil to Contacts: Transient Protection: MECHANICAL Enclosure: Weight: 4... DC: ± 0 C, AC: ± 3% + 0 C Adjustable ± 0% within temperature & voltage range 0 ms 00 ms (for timing cycle up to 0 sec) 50 ms (for timing cycle 0 to 300 sec) Silver cadmium oxide 0 0 / 40 VAC, 0 30 VDC, /3 / 40 VAC 00,000 rated load 0,000,000 no load AC: 4 to 40, DC: to 5 AC - 5% of nominal; DC - 0% of nominal 0% of nominal voltage -0 C to +0 C 500 V rms 500 V rms 000 VAC for 5 ms Clear polycarbonate 4 grams approx. PHONE: (43) FAX: (43) info@magnecraft.com Mating Sockets 0-50D-, 0-50D-, 0-44-, 0-45-: SCREW/DIN 0-9-, 0-0-: SCREW/PANEL See section, page -

23 3 & 3 OCTAL & PIN TIME DELAY RELAYS, & 3 POLE, 0 AMPS OUTLINE DIMENSIONS DIMENSIONS SHOWN IN INCHES & (MILLIMETERS). 0.5 (5.) 3.00 MAX. (.) (34.9) (34.9) PIN OCTAL OFF-DELAY.35 (34.9) PIN OCTAL ON-DELAY WIRING DIAGRAMS External Resistor for remote timing adjustment on models 3 or 3 with Code R. Observe Polarity on DC input models MODELS WITH INTERNAL RESISTOR OFF-DELAY ON-DELAY EXTERNAL SWITCH Jumper XAX4P 3XBX4P 3XCX4P 3XBX4P-K NON STANDARD MODELS WITH EXTERNAL (REMOTE) RESISTOR ON-DELAY OFF-DELAY EXTERNAL EXTERNAL EXTERNAL RESISTANCE RESISTANCE EXTERNAL RESISTANCE RESISTANCE EXTERNAL SWITCH XAX4P-R 3XBX4P-R 3XAX4P-R 3XBX4P-R CALL FACTORY FOR OTHER VOLTAGES, TIME AND FUNCTIONS EXTERNAL SWITCH 4...

24 POLES ALL STYLES 4 & 4 UL CONTACT LOAD RATINGS TABLE CURRENT OR HORSE POWER 0 AMP 5 AMP 0 AMP 0.5 AMP 3 AMP AMP 3 AMP 0. AMP LOAD VOLTAGE 40 VAC VDC 5 VDC 40 VAC VDC 5 VDC LOAD VOLTAGE FREQUENCY 50/0 Hz 50/0 Hz DC DC 50/0 Hz 50/0 Hz DC DC INDUSTRIAL DELAY TIMER RELAYS TYPE OF LOAD RESISTIVE RESISTIVE RESISTIVE RESISTIVE INDUCTIVE INDUCTIVE INDUCTIVE INDUCTIVE SUFFIX 9 WITH BLOWOUT MAGNET FOR DC SWITCHING (NOT UL OR CSA) SPST-NO SPST-NO-DM SPST-NO SPST-NO-DM SPST-NO SPST-NO-DM SPST-NO SPST-NO-DM.5 AMP 4 AMP 0.5 AMP.5 AMP 0.5 AMP.5 AMP 50 ma 0.5 AMP 5 VDC 5 VDC 50 VDC 50 VDC 5 VDC 5 VDC 50 VDC 50 VDC DC DC DC DC DC DC DC DC RESISTIVE RESISTIVE RESISTIVE RESISTIVE INDUCTIVE INDUCTIVE INDUCTIVE INDUCTIVE DPDT, 3PDT, 4PDT, DPDT WITH N.C & N.O., DPDT WITH N.O., 0 AMPS File No. E34 CAN SWITCH 30 AMP LOADS AND CARRY 0 AMPS CONTINUOUSLY AT VOLTAGES SHOWN IN UL CONTACT LOAD RATINGS TABLE. INSTANTANEOUS AVAILABLE Class 4 CSA Certified LISTED 3G UL Listed when used with type 390 socket THE CLASS 4 & 4 TIME DELAY RELAYS ARE ON-DELAY OR OFF DELAY, WITH RANGES FROM 0. TO 300 SECONDS. BOTH TIMERS INCORPORATE THE PROVEN INDUSTRIAL WORKHORSE CLASS 9 FRAME ALONG WITH A SOLID STATE MODULE. PRODUCTS ARE AVAILABLE WITH A VARIETY OF POLE AND CONTACT CONFIGURATIONS. A LARGE CHOICE OF OPTIONS IS AVAILABLE AND SWITCH UP TO 30 AMP LOADS. GENERAL SPECIFICATIONS Operating Modes Available: Repeatability: Accuracy: Recycle Time: False Contacting: Contact Material: Electrical Life: Mechanical Life: Coil Voltage Minimum Operate Voltage: Ambient Temperature Rating: Max. Allowed Voltage: PROTECTION Reverse Polarity: DIELECTRIC STRENGTH Across Open Contacts: Coil to Contacts: Transient Protection: MECHANICAL Enclosure: Weight: On delay, off delay ± 5 C (AC + ms) Adjustable ± 0% within temperature & voltage range 50 ms 0 to 300 Sec No false contacting if power is interrupted during timing cycle Silver cadmium oxide - gold diffused 00,000 rated load 0,000,000 no load AC - 5% of nominal DC - 0% of nominal AC: -0 C to +45 rated operation, DC: -0 C to +0 rated operation 0% of nominal voltage Yes - DC 500 V rms 500 V rms 000V for 5 ms Clear polycarbonate grams approx. PHONE: (43) FAX: (43) info@magnecraft.com Pin Versions Mating Socket: Pin Versions Mating Socket: 333 See section, page

25 4 & 4 INDUSTRIAL DELAY TIMER RELAYS ORDERING CODE FOR RELAYS CLASS: 4: ON DELAY, 4: OFF DELAY, 4 XBX P L -00-0A CONTACT ARRANGEMENTS: XBX: ( FORM "C") XCX: (3 FORM "C") ABA: ( FORM A & FORM C & FORM B). BBX: ( FORM A & FORM C) 4 ONLY. DPDT, 3PDT, 4PDT DPDT WITH N.C & N.O., DPDT WITH N.O., 0 AMPS OUTLINE DIMENSIONS DIMENSIONS SHOWN IN INCHES & (MILLIMETERS)..5 MAX (.) 0. (.) STANDARD FEATURES: PLUG-IN WITH POLYCARBONATE COVER: CODE P OPTIONS: INDICATOR LAMP: CODE L MANUAL ACTUATOR: CODE M BIFURCATED (5 AMPS MAX): CODE 33 PERMANENT MAGNET, BLOWOUT: CODE 9 ADJUSTMENT KNOB): NO CODE REMOTE ADJ. (EXT POT REQUIRED) : CODE R LOCKING SHAFT POT: CODE INSTANTANEOUS : CALL RANGES: SEC: CODE SEC: CODE SEC: CODE SEC: CODE SEC: CODE 00-0 SEC: CODE SEC: CODE 300 OVER 300 SEC: CALL FIXED: CODE F (EX. 3F) OPERATING VOLTAGE: 4, 4, 0, 40 ADD "A" FOR AC COILS, 4, 4, 0-5, 50 ADD "D" FOR DC COILS LOCKING CLIP WIRING DIAGRAMS 3.5 (95.).4 (3.) 4.5 (5.) EXT. TRIGGER EXT. TRIGGER TIME MOD TIME MOD TIME MOD TIME MOD 4XCXP 4XBXP 4BBXP 4XBXP TIME MOD 4ABAP XDXP 4PDT 4 CALL FACTORY FOR OTHER AGASTAT ALTERNATIVES CALL FACTORY FOR OTHER VOLTAGES, TIME AND FUNCTIONS 4...4

26 3 VOLTAGE SENSING RELAYS SPDT, 3 AMPS & DPDT, 0 AMPS CLASS 3 VOLTAGE SENSING RELAYS COMBINE A SOLID STATE SENSOR WITH A SPDT, 3 AMP OR DPDT 0 AMP RELAY. PULL-IN & DROPOUT VOLTAGES ARE INDEPENDENTLY ADJUSTABLE. THE 3 CAN BE USED EITHER AS A OVER OR UNDER VOLTAGE DETECTING RELAY. STATUS L.E.D. INCLUDED. File No. E3 APPLICATIONS: BROWNOUT PROTECTION, WARNING OF UNDER VOLTAGE CONDITIONS AND OVER VOLTAGE PROTECTION. PREVENTS EQUIPMENT BURNOUT. OPTIONAL TIME DELAY AVAILABLE IN OCTAL PIN VERSION GENERAL SPECIFICATIONS VOLTAGE SENSING: Nominal Input: Adjustment Range: Repeatability: Contact Material: Contact Rating: Electrical Life: Mechanical Life: Input Current: Temperature Range Operate: Temperature Range Storage: DIELECTRIC STRENGTH Coil to Contacts: Across Open Contacts: Transient: Noise Immunity: MECHANICAL Enclosure: Terminals: Power "ON" Indicator: Weight: 4, 0, 40, 40 VAC 50/0Hz, 4 VDC. other AC & DC voltages available Pull-in 5% to 5% of nominal voltage, Dropout 5% to 95% of pickup setting ± constant voltage & temperature Silver cadmium oxide SPDT: 3 40 VAC, VDC Res. /3 / 40 / 40 AC, 3 40 VAC, NEMA B300 pilot duty DPDT: 0 40 VAC / VDC Res. / Hp 40 VAC. NEMA B300 pilot duty 00,000 rated load SPDT: 5,000,000 operations DPDT: 0,000,000 operations 5 ma (. ma 40 VAC max. (.9VA) ma max. 40 AC (3.4 VA) - 30 C to + 55 C - 40 C to + 5 C 500 V rms 000 V rms UL 50 surge 5000 V for 50 microseconds NEMA ICS-30, 500 VAC. Polycarbonate dust cover 0. quick connect terminals, or pin octal base L.E.D. ( green) 4.4 grams, 55.5 grams ( pin octal) Mating Sockets 0-50D-, 0-50D-, 0-44-, 0-45-: SCREW/DIN 0-9-, 0-0-: SCREW/PANEL See section, page : SCREW/DIN 0-4-: SOLDER 0--, 0--: PRINTED CIRCUIT 0-4-: QUICK CONNECT See section, page, PHONE: (43) FAX: (43) info@magnecraft.com

27 3 VOLTAGE SENSING RELAYS OUTLINE DIMENSIONS DIMENSIONS SHOWN IN INCHES & (MILLIMETERS). SPDT, 3 AMPS & DPDT, 0 AMPS.93 (4.4).5 (44.4) L.E.D FIGURE A.3 (0.35) MAX. (3.) 0.3 (.9).53 (3.) WIRING DIAGRAM FIGURE B.40 (35.) A B RECESSED SCREW ADJUSTMENTS PIN OCTAL.50 (3.) PULL-IN DROPOUT 4 5 L.E.D 9 A B SQUARE BASE CONTINUOUS VOLTAGE MUST BE SUPPLIED TO. STANDARD PART NUMBERS FIG. NOMINAL VOLTAGE VOLTAGE PULL-IN RANGE VOLTAGE DROP-OUT RANGE W3ACPX- W3ACPX-4 W3CPX- W3ACX- W3ACX- W3ACX-3 CALL FACTORY FOR OTHER VOLTAGES, TIME AND FUNCTIONS A A A B B B 4 VAC 4 VDC 0 / 0 / 40 VAC 9 TO 40 VAC 0 TO 30 VAC 0 TO 30 VDC 90 TO 3 VAC 0 TO VAC 30 TO 55 VAC 5% TO 95% OF PICKUP VOLTAGE SETTING 4...

28 Your Contact for Relays SECTION 4 CROSS REFERENCE GUIDE MAGNECRAFT & STRUTHERS-DUNN WACPSOX- WACPSOX-5 WACPSOX- WACPSOX- WACPSOX-0 WACPSOX- WACPSOX- WACPSOX-3 WCPSOX- WACPSRX-5 WACPSRX- WCPSRX- WCPSRX-3 MAGNECRAFT & STRUTHERS-DUNN TDRPRO-5000 TDRPRO-500 MAGNECRAFT & STRUTHERS-DUNN WCPSOX- WCPSOX- MAGNECRAFT & STRUTHERS-DUNN WACPFX- WACPFX- POTTER & BRUMFIELD CDB RSSAN-0A CDB /CGB-3-000S/ RSSAN-5A CHB-3-000/CKB-3-000/ CB-003B-0 RSSAN-40A CKB-3-00/CHB / RSSAN-50A CB-005B-0/CDB RSSAN-5A CGB M - CGB-3-000M - - CGB M RSSAN-50A CB-00B0 RSSAN-5A CHD /CB-0D-30/CDD RSSAN-90A CHB-3-00/CB-0B- - CHB CHD CHD /CDD RSSDN-0A RSSDN-5A POTTER & BRUMFIELD - CNM5, CNS-35-9, RSSDN-50A CNS-35- CN, CNS-35-9, CNS-35- RSSDN-5A RSSDN-0A POTTER & BRUMFIELD RSSDN-5A R30XE - R304XE RSSDN-50A RSSDN-5A SQUARE D RSSDN-90A 9050JCK5V0-9050JCK5V0 CUTLER HAMMER MTONP0A MTONP0A MTOFP0A MTOFP0A SQUARE D JCK0, JCK0 NTE R-A0-0M SIEMENS OND-00-0A OND-0-0A OND-00-4D OFD-00-0A OFD-0-0A SQUARE D 9050JCKV0 9050JCK5V0 9050JCKV0 9050JCKV0 9050JCKV0 9050JCK9V0 9050JCKV0 9050JCK5V0 THE CROSS REFERENCE IS INTENDED TO MATCH FOOT PRINT, INTERNAL WIRING, AND CONTACT LOAD RATINGS. CONSTRUCTION FEATURES AND GENERAL SPECIFICATIONS SHOULD BE COMPARED IF EXACT REPLACEMENT IS REQUIRED. MAGNECRAFT & STRUTHERS-DUNN POTTER & BRUMFIELD CUTLER HAMMER MIDTEX W3ACPSOX- W3ACPSOX- W3CPSOX- W3CPSOX- W3CPSRX- W3ACPSOX-4 W3ACPSOX-44 W3CPSRX- W3CPSRX-4 CLF CLH MTONB0A MTONB0A 4-T400 4-C400 -C400-43T T400-43C00-43C FOR TIME DELAY APPLICATION ENGINEERING ASSISTANCE ANCE Scott Heilman, PRODUCT MANAGER FAX: (43) sheilman@magnecraft.com FAX ON DEMAND: DOCUMENT: 500 U. S. A. TELEPHONE: (43) FAX: (43) WEBSITE: info@magnecraft.com EUROPE TELEPHONE: 499 / FAX: 499 / WEBSITE: renatesteinback@magnecraft.de