ORDERING INFORMATION T79D

Transcription

1 Action Instruments Isolating Two-Wire Transmitter Isolated, Linearized Current Loop Output for an RTD or Thermocouple Input HART Compatible or Field Configurable with Optional Display Intrinsically Safe Operation or with Display and EP Enclosure Programmable for 11 T/C Types, 6 RTD Types, mv or Ohm inputs The model T798 is a programmable temperature transmitter that can be factory or field configured using the optional 1 or 2 line alphanumeric display. The model T798 is Highway Addressable Remote Transducer (HART) based, temperature transmitter that can be factory or field configured using an optional 1 or 2 line alphanumeric display, optional PC based modem and software. Alternatively an HC275 Hand-Held Communicator loaded with the Action T798 Device Description from the Hart Foundation Library can be used. Both the T798 and T797 accept thermocouple (B, C, E, J, K, L, N, R, S, T, U & special) and 2, 3, or 4 wire Platinum RTDs (385 or 392 alpha) as well as millivolt (mv) and resistance inputs. Linearization: Thermocouple and RTD linearization to ±0.05 C. Analog, two-wire 4-20 ma Transmitter ±0.05% of the millivolt or ohm equivalent input reading, or the value from the Accuracy Table, whichever is greater; plus ±0.05% of the span. For thermocouples, add ±0.5 C (0.9 F) for cold junction compensation. Output Analog Zero: 100% of Sensor range - Non-interacting Adjustments: Analog Full-scale: Normal or Reverse Acting Operating Temperature: Electronics & Display (with reduced visibility): -40 C to 85 C, (-40 F to +185 F) Display (full visibility): -20 C to +70 C, (-4 F to +158 F) T79D T Temperature Transmitter, Non IS T Temperature Transmitter, IS-FM/CSA T Temperature Transmitter, Hart, Non IS T Temperature Transmitter, Hart, IS-FM/CSA Displays & Options T79D-2000 Two Line Alphanumeric Display T79D-1000 One line alpha-numeric Display T79E-1000 Weather Proof Head-Mount Enclosure T79A-P000 Pipe Mount Bracket for T79E-0/D only T79A-D000 DIN Rail Mounting Kit T79A-M000 T797 Configuration Modem T79A-MH00 T798 Hart Configuration Modem T79A-C000 Configuration Software for T797 & T798 Action Instruments DC Input, Field Configurable Isolator with Math Functions Multi-Function, Multi-Channel Input. DC-Frequency or Frequency-DC Conversion for Totalization/ Integration Applications. Math Capability Supports Many Process Control Functions. Switch Selectable or PC Programmable Ranges. The Q498 is a DC powered, DIN rail mount, DC input signal conditioner. The unit is fully isolated to 1800V between input, output and power. Two isolated analog inputs each accept either a DC voltage or current. One analog output delivers either DC bi-polar voltage or uni-polar current. The Q498 also has a separated frequency input channel and a frequency output, as well as a discrete input and output channel. The Q498 can perform single or double input math calculations on the input values. The available operators are: +, -, *, /, Sq, Sqroot & Average. Process control functions include Hi/Lo Select, Rate of Change Limiter and Track & Hold. The frequency input can also have the math functions applied. A 25-point linearization function is available for Channel 1 Analog input only. All output math and process control functions require the C698 software. Analog Input Ranges ±150mV, ±1.5V, ±15V, ±150V (Two Isolated Channels) ±2.5mA, ±25mA Analog Maximum Overload 200V DC for voltage inputs; 170mA DC and/or (continuous) 60V DC maximum for current inputs (self-resetting fuse) Analog Output Ranges 0-20mA, 0-10V, ±10V Analog Output Drive 0-20mA: 12VDC compliance. (600Ω maximum) Voltage ranges: 10mA drive (1000Ω load minumum) Analog Output Accuracy ±0.005% of the FS Input Range (±0.05% on 150 volts range), plus ±0.05% of the FS Output Range (±0.1% for output loads <200Ω) Analog Response Time 750msec max. (10-90%) Analog Input Impedance 100kΩ on voltage ranges > 1.5V, 10MΩ on voltage ranges <1.5V 70Ω typical (non-overload) on all current ranges Analog Output Impedance Less than 3Ω on voltage output ranges 500kΩ on current output ranges Frequency Input One channel with two voltage range inputs: 150mV to 50Vrms with 5Vp noise suppression, or 0.5V to 150Vrms with 20Vp noise suppression, 2Hz to 10kHz in software selectable ranges. Frequency Output ±0.1%, 2Hz to 10kHz in software selectable ranges Open collector pulled up through 20k to 18V, with 1mA drive.sinks up to 20mA from 24V external supply. Discrete Input Input active to Common, with soft pull-up (1mA) to +18V CMR (DC to 60Hz) 90dB for 60Hz and DC Power Requirements 9-30VDC, 2.5 watts max Isolation Input to Input to Output to Power, 1800VDC Size DIN rail case (0.88" x 4.0" x 4.59") Operating Temperature 0 C to + 55 C (32 to 131 F) Q DC Frequency Isolator C Configuration Software & PC Serial Cable H Amp, 24VDC Power Supply H910 1Amp, 24VDC Power Supply H Amp, 24VDC Power Supply 82

2 Action Instruments Low Profile Signal Conditioners Low Power Higher Accuracy Field Configurable Alarm Notification Accuracy (In/Out): Isolation: Operating Temp: Power: Alarm: Size: Approvals: SlimPak II 0-10V, 0-20mA, 4-20mA ±0.015% rng / ±0.05% rng 1800V AC/DC, In/Out/Power 0 to 60 C, <95% RH 9-30VDC, 1W typ. 2 SPDT, 5A@120VAC 0.5" wide DIN rail case UL508, CSA C22.2, CE Model Function Range WV DC ±150mV, 1.5/15/150V, 2.5/25mA +reverse WV RTD 2/3/4 wire: Pt100, Cu10 WV T/C J,K,T,R,S,E,B,N,C,B WV Potentiometer 100Ω to 100kΩ WV Bridge ±5/10/20/50/100/200mV (1-10VDC, 120mA excitation) WV AC 50/150/500mV, 5/20/50/150/250V, 20/100mA +reverse (40-400Hz) WV Frequency 0-10kHz (150mV-150V) WVC Communication Up to 32 modules to Ethernet 10Base-T C Software Includes serial cable WV905 Power Supply Also available as Limit Alarms with latching relays & reset switch Pyromation Temperature Transmitters Wide Operating Temperature Range Factory or Field Configurable Sensor Break & Short Circuit Detection T/C Head Mounting (441 & 442) Industrial or Explosion Proof Housing (642) FM & CSA Approved Intrinsically Safe & Non-Incendive Input: Maximum Load: Power Supply: Operating Temperature: Dimensions (441, 442): Galvanic Isolation: T/C J,K,T,E,R,S,B,N,L,U,C,D RTD Pt or Ni, 100/500/1000, 2/3/4-wire DC -10 to 100mV Resistance 400Ω, 2000Ω 0.2 C (Pt100), 1 C (K T/C) 2-wire, 4-20mA or 20-4mA (Vsupply - 8V)/25ma 8-30V DC (40V max on 642 models) -40 to 85 C, condensing allowable 1.73" dia x 0.9" (44x23mm) 3.75kV AC NLS Series 8000 Signal Conditioners Input, Output, Isolation, Power Supply and Special Functions Combined in One Low Cost Modular Unit Field-Settable Range, Span and Configuration Fuse Protected Linear Power UL Recognized High Impact, Flame Retardant Polycarbonate Case The Series 8000 signal conditioners are designed with a modular architecture to allow full input, output, and special function selectability and interchangeability. They can also be used as isolators, signal amplifiers, and transmitters. 85 PM/441 Temperature Head Transmitter PM/442 Temperature Head Transmitter with HART protocol PM/642A Programmable HART Transmitter PM/642AT Programmable HART Transmitter with digital display PM/642C Programmable HART Transmitter, explosion proof housing For factory configuration, specify input type & range ( C or F); for field configuration, order communication cable & software

3 Fluke Process Loop Calibrators TEST EQUIPMENT Fluke 705 Loop Calibrator Simultaneous ma and % Readout Fast Span Check Selectable Slow Ramp, Fast Ramp & Step 24V Internal Loop Supply Fluke 707 Loop Calibrator 705 Features, Plus: Output Adjustment Dial HART Mode 0.015% Accuracy Functions Fluke 705 and 707 Fluke 715 Fluke 787 and 789 Voltage measurement Range 0-28 V dc mv 0-10 V V ac or dc Resolution 0.001V 10 µv 1 mv 0.1mV to 1.0V Accuracy 705: 0.025% Rdg + 1 LSD 0.02% Rdg + 2 LSD 0.1% Rgd + 1 LSD (VDC) Current measurement Range 0-24 ma 0-24 ma 0-1A dc 0-30 ma dc Resolution ma ma 1mA dc ma dc Accuracy 705: 0.02% Rdg + 2 LSD 0.015% + 2 LSD 0.2%+2 LSD 0.05%+2 LSD Current sourcing Range 0-20 ma or 4-20 ma ma or 4-20 ma ma or 4-20 ma 1 Accuracy 705: 0.025% Rdg + 2 LSD 0.015% Rdg + 2 LSD 0.05% of span Drive capability 705: 24 ma 24 ma 787: 24 ma 707: 24 ma 789: 24 ma Loop power while 24V 24V 24V (789 only) measuring ma Voltage sourcing N/A mv or 0-10V N/A Resistance N/A N/A to 40MΩ, 0.2% + 1 LSD measurement Frequency N/A N/A to khz,0.005% + 1 LSD Diode test N/A N/A 2.4 V shows diode voltage drop Continuity N/A N/A Beeps for resistance <100 ohms Display current Yes ma or % Yes and % of span Auto step, auto ramp Yes No Yes Span Check Yes No 789 only 1 Will over-range to 24 ma Fluke Temperature Calibrators 712 Fluke 712 RTD Calibrator Rosemount pulsed transmitter compatible (pulses >100ms) Measure temperature from RTD output Simulate RTD output Operates with seven types of RTD Measure additional RTDs using Ohms measurement function Simulate additional RTDs using Ohms source function F or C selectable Four shrouded banana jacks Fluke 787 Process Meter DMM and Loop Calibrator Backlit LCD 1000V Overload Protection on V, Ohms, Frequency Fluke 789 Process Meter 787 Features, Plus: 24V Loop Power Supply HART Mode Fast Span Check Fluke 715 Volt/mA Calibrator Measure loop Currents and Process Voltages Source Loop Currents to 24mA Source Voltage to 10V Fluke 714 Thermocouple Calibrator Measure temperature from TC output Simulate TC output Operable with nine types of thermocouples Calibrate linear TC transmitter with mv source function Selectable F or C Thermocouple mini-jack termination Available as accessories: Fluke 700TC1 and TC2 Thermocouple Mini-plug Kits Model Function Range Resolution Accuracy Notes Fluke-712 Measure/simulate -200 to 800 C 0.1 C, 0.1 F 0.33 C, 0.6 F Pt; (385); RTD (Pt 100) (Pt 100) Pt 100 (392); Pt 100 (392) JIS; Ni 120 (672) Measure/simulate 15 Ω to 3200Ω 0.1Ω 0.1Ω to 1 Ω Resistance Fluke-714 Measure/simulate -200 to 1800 C, 0.1 C or F 0.3 C + 10 µv 9 TC types; J K T E R S B per NIST Thermocouple depending on type (1 C or F; BRS) 175 and ITS-90 L U per DIN (K,-200 to 1370 C) and PTS-68 Measure/simulate -10 to 75 mv 0.01 mv 0.025% mv + 1 count 167

4 Martel Beta Process Calibrators Multi-Function MC 1200 Measure and source T/Cs, RTDs, Ohms, current, voltage, frequency; source pulse trains Isolated ma/v read-back for complete transmitter calibration Pressure module communication port Built-in 24 V supply drives 4 20mA loops Direct entry of custom RTD coefficients All source modes can be programmed with setpoints to speed linearity tests Highest accuracy in class (to 0.015% rdg.) Read and Source Voltage Current (ma) Source to VDC to ma Read Isolated to VDC to ma Read Non-isolated to VDC to ma Accuracy ±0.015% of rdg ±2 µv ±0.015% of rdg ±2 µa Frequency (1-20 V amplitude) Thermocouple mv CPM Source & Read 2.0 to CPM Read & Source to mv Hz Source & Read 1.0 to Hz Accuracy ±0.02% of rdg, ±10 µv khz Source & Read 1.0 to khz Ohms Pulse Source (1-20 V amplitude) Pulses 1 to 30,000.0 Rate 2 CPM to 10 khz Read and Source Range (Accuracy) C J to (0.2) K to (0.3) T to (0.2) E to (0.2) R to (1.2) S to (1.2) B to (1.2) C 0 to (0.6) XK to (0.2) BP 0 to (0.9) L to (0.2) U to (0.25) N to (0.4) Operating Temperature: -10 C to +50 C Stability: ±0.005% of reading/ C outside C Dimensions 8.7" x 4.2" x 2.3" Loop Calibrator Simulates, powers & measures two-wire transmitters Five preset outputs (4, 8, 12, 16, 20 ma) ma resolution Adjustment level knob % Error function eliminates manual calculation Measures loop power & Hart devices LC-100 Current Source & Measure Range: to ma, -25 to +125 % Voltage (Reading): 0 to 28 VDC Input Protection: Fuseless, up to 250 VAC Drive Capability: 1200Ω without Hart, 950Ω with Hart Loop Supply: 24 VDC Range Select: Decade Incremental to ma steps Resolution: 1 µa ±0.015% of reading ± 2 µa Operating Temp.: -10 to +55 C Dimensions: 5.7" x 3.15" x 1.43" Source 5.0 to 4000Ω Read 0.00 to Ω Read and Source Range (Accuracy) C Ni120 (672) to (0.2) Pt100 (385) to (0.2) Pt100 (3926) to (0.2) Pt100 (3916) to (0.2) Pt200 (385) to (0.8) Pt500 (385) to (0.4) Pt1000 (385) to (0.2) Cu to (1.4) YSI to (0.1) Cu to +200 (0.4) Cu to +200 (0.3) Pt to (1.4) Pt to (0.4) Thermocouple Calibrator Universal Temperature 10 T/C types plus mv ±0.3 C accuracy (type J) Accepts T/C mini-plug & bare T/C wires 3 setpoints for each T/C type MIN/MAX recall in measure mode Input protection to 240 VAC TC-100 Voltage Source & Measure Range: -10 to mv Resolution: 1 µv ±0.007% of reading, ±10 µv Output Impedance: 1 Ω Input Impedance: >1 MΩ Thermocouple Source/Measure Types: J, K, T, E, R, S, B, L, U, C Resolution: 0.1 C or F source 0.01 C or F measure Operating Temp: -10 C to +55 C Dimensions: 5.7" x 3.15" x 1.43" Calibrate thermocouples and RTDs with one unit Works with smart (pulsed) transmitters Direct keyboard entry or scroll control 9 user-defined setpoints for each type Rugged NEMA 4X case High accuracy ±0.4 C J T/C, ±0.3 C 4w RTD Auto step function PTC 8001 Read & Source Range NI120 (672) to J to Pt 100 (385) to K to Pt 100 (3926) to T to Pt 100 (3916) to E to Pt 200 (385) to R to Pt 500 (385) to S to Pt 1000 (385) to B to Cu to L to YSI to 50.0 U to Ohms 0.0 to 400.0, N to to 3200 mv to plus Pt 392, JIS, Ni120 Connectors: Standard mini-plug for T/C, banana jack for RTDs Operating Temp.: -10 to +50 C Dimensions: 8.7" H x 4.2" W x 2.3" D MA/MC-1200 Multi-Function Calibrator with test leads, 4 AA batteries, NIST certificate MA/PTC8001 Universal Temperature Calibrator with test leads, 4 AA batteries, NIST certificate MA/IVC-222 HP11 Voltage/Current Calibrator with test leads, carrying case, 9V battery, NIST certificate MA/TC-100 Thermocouple Calibrator with 9V battery, NIST certificate MA/LC-100 Loop Calibrator with test leads, 9V battery, NIST certificate MA/CC572 Carrying Case for PTC8001, MC-1200 A variety of temperature probes are available. Voltage/Current Calibrator 0.015% of reading accuracy 200 mv, 2 V, 20 V and 24 ma ranges 24 V supply can drive 4-20 ma loops 2 stored setpoint values Intuitive, easy-to-use controls IVC-222HPII Resolution Voltage: 0.01 mv, V, 0.001V Current: ma ±0.015% of reading, ±2 count; 18 C to 28 C Temp. Stability: ±0.005% FS/ C Load Capability Voltage: ±1 ma for rated accuracy Current: 1kΩ Output Protection: Current limited internal RESET Operating Temp: -10 C to +55 C Dimensions: 1.43" x 3.15" x 5.7" 166 TEST EQUIPMENT

5 Pyragon Loop Isolator Signal Powered CMOS Circuitry Precise Duplication of Input Signals 4 20 or ma, Same Unit High Common Mode Rejection 1500 VRMS Isolation Mounts on Bulkhead or in 3" Conduit Box 10AI Provides the Necessary Signal Isolation for Noisy Process Circuits If your process signals are influenced by ground loops, high common mode noise, or other interference, you need the Transmation Model 10 Auto-Isolator. Requiring no separate power supply, Auto-Isolator operates efficiently from input signal current, and precisely retransmits the current applied to the input with an accuracy of ±0.1% of span. Usable with milliamp signal ranges of 4 20, 10 50, or other ranges between 4 and 50 ma. The instrument can be bulkhead-mounted or installed in a 3-inch cast conduit box. A trim potentiometer, accessible through the instrument s top plate, permits precise adjustment of current transfer as a function of load resistance up to 500 ohms at 20 ma, and 250 ohms at 50 ma. Input: 4 20 ma, ma, or other spans within range of 4 50 ma Output Ratings: 4 20 ma with loads from ohms ma with loads from ohms ±0.1% of span Size/Weight: 2.95" diameter, 1.88" high/6 oz Pyragon Universal Temperature Transmitters 10AI Model 10 Auto-Isolator 10AI-EXP Model 10 in Explosion Proof Housing Configurable for Eight T/Cs, 12 RTDs, Millivolts, Ohms Unmatched Programmability: Input Type, Range, Zero, Span, Linear Output, Engineering Units; Calibration Runs Exceptionally Economical: Reduces Inventory and Maintenance Costs Built for Reliability: RFI Protected, Isolated, Environmentally Tough, Five-Year Warranty Input Types Thermocouple: Types J, K, T, E, R, S, N, B RTD: Pt DIN (50, 100, 200, 500Ω); Pt JIS C 1604 (100Ω); Pt Burns α (100, 200, 500Ω); Ni Bristol s 7NA (110Ω); Ni Minco (120Ω); Cu Minco (10Ω); Cu China α (50Ω) mv: -100 to mv Resistance: 0 to 1000Ω ±0.05% of span ±1 digit Input Span Limits: Any span within range limits Input Resolution: 0.1, 1 µv, 0.005Ω Output Range: 4 to 20 ma, calibrated; 3.7 to 22 ma, maximum Output Resolution: ma RTD Excitation Current: 200 µa, typical Temperature Effect T/C and mv: ±0.2 µv/ C max ±0.005% of input reading/ C RTD and Ω: ±0.002 Ω/ C max ±0.005% of input reading/ C Loop Supply Voltage: 13V + (load resistance x 20 ma), min; 48V, max Size 3.10 x 1.75 x 3.77" HWD 2800T 2800T Universal Temperature Transmitter, Digital Display (NI FM Approved) 2800T-EXP 2800T in Explosion Proof Housing 2850T 2800T with HART Protocol mm DIN Rail Adaptor 2800T mm DIN Rail Adaptor 2800T 86