XYR5000 Series Wireless Transmitters

Transcription

1 Illinois, Indiana, Iowa, and SW Michigan XYR5000 Series Wireless Transmitters 1 Digital Indicators Controllers and Pressure Transmitters Analytical Instruments For more information:

2 Controllers and Digital Indicators Analytical Instruments Pressure Transmitters 2 Illinois, Indiana, Iowa, and SW Michigan XYR5000 Series Wireless Transmitters The pressure is on to improve your process and take product quality to the next level, to operate flexibly and maintain high uptime, to meet regulatory requirements and cut operating costs. All with fewer resources. How will you accomplish these goals if the information you need is too difficult or expensive to access? Introducing Honeywell Wireless Transmitters Honeywell XYR5000 Wireless Transmitters break down the barriers to monitoring variables in areas where traditional hard-wired transmitters are too costly, difficult, or time-consuming to implement. These instruments are designed for applications with no access to power, that are remote or difficult to access, that require frequent changes in instrumentation schemes, or where manual readings are typically taken. The Honeywell XYR5000 family includes instruments for accurately monitoring gauge pressure, absolute pressure, acoustic signals, and temperature. The line also includes an analog input interface for adding wireless capabilities to 4 20mA and 1 10V devices. The instruments wirelessly transmit their measurements to a base radio connected to a control system or data acquisition device such as a recorder or PC. Each base radio accepts the signals of up to 50 transmitters. The base radio also interfaces with Honeywell s PC-based Wireless Management Toolkit, which offers real-time indication, trending, reporting, and configuration capabilities. The base radio is available with Modbus or 4 20mA analog signal output for flexible communications with your control system. Enjoy the Benefits of Wireless Technology Today Designed to integrate seamlessly with control platforms such as Honeywell Experion PKS, XYR5000 Wireless Transmitters provide information that helps you to achieve key objectives: Improve Product Quality With XYR5000 transmitters, you can easily increase the number, frequency, and type of measurements. In addition, you can improve accuracy and consistency of measurement by replacing manual readings with automated online data collection. Online communication with your control system also helps ensure precise time tracking of information for use in troubleshooting process problems. Ensure High Uptime With more frequent measurements and early detection of asset problems, you can reduce or even prevent incidents and accidents. Reduce Maintenance and Operational Costs These transmitters allow you to monitor a whole range of assets (e.g., furnaces, pumps, heat exchangers, and steam traps) to support proactive, predictive maintenance. Additionally, XYR5000 transmitters help identify potential problems that can be costly in terms of excess use of energy and raw materials. Once XYR5000 instruments are in place, you ll make better use of personnel time. Meet Regulatory Requirements XYR5000 transmitters can help you meet regulatory requirements by recording changes and sending data to the control system for date and time stamping. These instruments allow flexible monitoring of process variables throughout critical phases of your process. In fact, the transmitters can even move with the process. XYR5000 transmitters support safety by making data available in the control room, reducing human exposure to hazardous areas and products. The transmitters also help improve waste treatment processes and reduce environmental impact by enabling online measurement of additional remote variables, such as waste pond level, which are often measured only locally. Enhance Flexibility Because XYR5000 transmitters are so easy and affordable to install, you can add or change measurements as A complete XYR5000 wireless system includes: WBR wireless base radio: one base radio per every 50 communicating field units, with the corresponding number of quad analog output modules for 4 20 ma outputs as needed. Wireless management toolkit software: single user license to run the RF server, configuration, and management tools. Any combination of the following: WI550 analog input field transmitter (for 4 20 ma or 1 10V signals); WT530 temperature transmitter for thermocouples and Pt100Ω RTDs; WG510 gauge pressure; WN571 for acoustics; or WA510 absolute pressure transmitters. Be sure to request a Site Survey on page 7 to guarantee performance. needed. This flexibility supports process improvement and development of new and better products in pilot plants. Overcome Measurement Hurdles Cost Going wireless means faster, easier installation and wiring savings of $10 to $40 per foot. Time Simplified installation leads to faster start-ups and accelerated profits. Range The instruments transmit measurements up to 2,000 feet, line-of-sight. Actual range may vary depending on plant topography. Accuracy Gauge pressure, absolute pressure, temperature, and analog input devices offer exceptional accuracy of ±0.1% of fullscale reading at reference conditions. Reliability Reliable XYR5000 transmitters feature long battery life (3 to 5 years) and a low-battery alarm. Self-checking software and hardware continuously monitor instrument operation to identify and report sensor or device parameters that are out of specification. All XYR5000 instruments avoid signal interference by using Frequency Hopping Spread Spectrum (FHSS). This technique modulates the data signal with a carrier signal that, over time, hops from frequency to frequency across a wide band. Ruggedness Rated for industrial use, XYR5000 transmitters go where you don t want to: hazardous, remote, or hard-to-reach locations.

3 Illinois, Indiana, Iowa, and SW Michigan XYR5000 Wireless Gauge and Absolute Pressure Transmitters The WG/A510 is part of the XYR5000 family of wireless products. These transmitters cover a wide pressure range, and can be used to monitor a variety of processes and assets in hazardous and remote areas. Since there are no wires to run, the transmitter can be installed and operating in minutes, quickly providing information about the monitored variable. The transmitter combines a high accuracy piezoresistive sensor with a Radio Frequency (RF) transceiver that communicates in a digital protocol, using Frequency Hopping Spread Spectrum (FHSS). FHSS ensures data integrity by continually switching the carrier wave over a wide range of frequencies. Power is supplied by a C size 3.6 V lithium battery, with an expected lifetime of up to five years. The XYR5000 Smart Response Manager allows the transmitter to adapt to changing process conditions, allowing greater visibility to process variation. Smart Response Manager allows the user to set thresholds which, when exceeded, cause the transmitter to adjust sampling and data transmission rates. Specifications Performance Accuracy (Linearity and Hysteresis): ±0.1% full scale over temperature Combined Zero and Span Stability: Less than ±0.1% of sensor URL per 21 C (70 F) Resolution: 24-bit A/D converter Self-Diagnostics: Self-checking software and hardware that identifies and reports out of spec conditions, and field unit low battery voltage Configuration Panel: 7-digit, high-contrast, anti-reflective monochrome integrated LCD display with membrane switch buttons for local configuration. Display cycles between pressure level and RF status Humidity: 99% RH (non-condensing) Temperature: Ambient Sensor: -40 to 230 F (-40 to 110 C); Ambient Electronics: -40 to 185 F (-40 to 85 C); Process Fluid: -40 to 250 F (-40 to 121 C); Display (Full Visibility): -4 to 158 F (-20 to 70 C); Display (Reduced Visibility): -40 to 185 F (-40 to 85 C) Process Connections: 1/2" NPTM Base Material (Bob-Wetted): 304 SS Electronic Housing: GE Lexan. V0 Rating and UV Stable Wireless Communication: 902 MHz 928 MHz Frequency Hopping Spread Spectrum (FHSS); FCC certified ISM license-free band; Every data block transmitted is verified (CRC check) and acknowledged by the Base Radio Data Rate: Configurable: 4.8 Kbps, 19.2 Kbps, or 76.8 Kbps Antenna: Internal 3" omnidirectional, 1/4 wave, monopole of sight. (Actual range may vary depending on site topography. ) Two membrane switches on the unit s front allow configuration of: RF Channel Setup: 1 to 16. Baud Rate: 4.8 Kbps, 19.2 Kbps, 76.8 Kbps. RF ID: 1 to 50. Password. Tag Name (up to 21 characters). Normal Transmit Rate: (1 5, 10, 15, 20, or 40 sec, 1 min). Normal Sampling Rate: (1 10, 15, 20, or 30 sec, 1 min). Abnormal Transmit Rate: (1 5, 10, 15, 20, or 40 sec, 1 min). Abnormal Sampling Rate: (1 10, 15, 20, or 30 sec). Pressure Normal Upper and Lower Values: Disabled/Enabled. Enabled to change Sampling and Transmit rates during abnormal process conditions. Engineering Units: PSI, bar, mbar, Pa, kpa, Torr, Atm, inh 20, inhg, fth20, mmhg, g/cm 2, kg/cm 2. Pressure Zero. Offset: Transmits user-defined offset instead of actual value. Trim: Applies a user-defined one- or two-point correction curve to the actual value. Vibration/Shock: Certified per IEC EN (Vibration) and 2-27 (Shock) Random Vibration: Certified to withstand 6 Gs, 15 minutes per axis from 9 to 500 Hz CE Compliance: Operates within Specifications in fields from 80 to 1,000 MHz with Field Strengths to 30 V/m. Meets EN General Immunity Standard and EN Compatibility Emissions Standard Environmental Protection: NEMA 4X (Pending) Electrical Classification: FM Rated Intrinsically Safe for Class I, Div. 1, Groups A-D; Class II, Div 1, Groups E-G; Class III, Div 1 (Pending) XYR5000 Wireless Pressure Transmitters Span Diaphragm Body 0 30 PSIG 316L SS 316 SS WG511 $ Gauge PSIG 316L SS 316 SS WG Pressure PSIG 316L SS 316 SS WG PSIG 17 4 ph 316 SS WG Absolute 0 30 PSIA 316L SS 316 SS WA Pressure PSIA 316L SS 316 SS WA Accessories RS485 to RS232 Converter Kit DIN-Rail Mounted Quad 4 20 ma Output Module DIN-Rail Mounted Power Supply: 120/240 VAC to 24 VDC/15W Starter Kit: 24 VDC Power Supply, RS485 to RS232 Converter Kit, 20' (6m) RS485 Shielded Starter Kit: 24 VDC Power Supply, RS485 to RS232 Converter Kit, 50' (15m) RS485 Shielded Starter Kit: 24 VDC Power Supply, RS485 to RS232 Converter Kit, 100' (3m) RS485 Shielded Lithium Battery: C Size, 3.6V Base Radio 2" Mounting Bracket Need a cylinder bracket or split clamp bracket? Call Lesman. 3 Digital Indicators Controllers and Pressure Transmitters Analytical Instruments

4 Controllers and Digital Indicators Analytical Instruments Pressure Transmitters 4 Illinois, Indiana, Iowa, and SW Michigan XYR5000 Wireless Temperature Transmitters The WT530 Temperature Transmitter is part of the XYR5000 family of wireless products. These transmitters are wireless temperature transmitters that can be used to monitor a variety of processes in hazardous and remote areas. Since there are no wires to run, the transmitter can be installed and operational in minutes, quickly providing information about the variable being monitored. The transmitter combines an integrated temperature sensor, with a Radio Frequency (RF) transceiver that communicates in a digital protocol, using Frequency Hopping Spread Spectrum (FHSS). FHSS ensures data integrity by continually switching the carrier wave over a wide range of frequencies. Power is supplied by a C size 3.6 V lithium battery, with an expected lifetime of up to five years. The Smart Response Manager allows the transmitter to adapt to changing process conditions, allowing greater visibility to process variation. Smart Response Manager allows the user to set thresholds which, when exceeded, cause the transmitter to adjust sampling and data transmission rates. Two membrane switches on the unit s front allow configuration of: RF Channel Setup: 1 to 16. Baud Rate: 4.8 Kbps, 19.2 Kbps, 76.8 Kbps. RF ID: 1 to 50. Password. Tag Name (up to 21 characters). Normal Transmit Rate: (1 5, 10, 15, 20, or 40 sec, 1 min). Normal Sampling Rate: (1 10, 15, 20, or 30 sec, 1 min). Abnormal Transmit Rate: (1 5, 10, 15, 20, or 40 sec, 1 min). Abnormal Sampling Rate: (1 10, 15, 20, or 30 sec). Temperature Normal Upper and Lower Values: Disabled/ Enabled. Enabled to change Sampling and Transmit rates during abnormal process conditions. Engineering Units: C, F, Kelvin, Rankin. Probe Type. Offset: Transmits user-defined offset instead of actual value. Trim: Applies a user-defined one- or two-point correction curve to the actual value. Specifications Performance Accuracy: ±0.1% of full scale reading at operating conditions. For cold junction compensation (T/C only), add 1.8 F (± 1 C) at reference conditions Linearization: RTD and T/C linearization to ± 0.09 F (± 0.05 C). Custom linearization with 22 point curve Ambient Temperature Effect: RTD: ± 0.002% reading per C; T/C: ±0.01% reading per C Long Term Stability: Stability deviation per year is less than 0.025% Self-Diagnostics: Self-checking software and hardware that identifies and reports out of spec conditions, and field unit low battery voltage Configuration Panel: 7-digit, high-contrast, anti-reflective monochrome integrated LCD display with membrane switch buttons for local configuration. Display cycles between temperature level and RF status. Humidity: 99% RH (non-condensing). Temperature: Ambient Sensor: -40 to 230 F (-40 to 110 C); Ambient Electronics: -40 to 185 F (-40 to 85 C); Process Fluid: -40 to 250 F (-40 to 121 C); Display (Full Visibility): -4 to 158 F (-20 to 70 C); Display (Reduced Visibility): -40 to 185 F (-40 to 85 C) Thermowell Material: 304 SS, 316 SS Electronic Housing: GE Lexan. V0 Rating and UV Stable Process Connections: 1/2 NPTM for probe only. 3/4 NPTM for well Wireless Communication: 902 MHz 928 MHz Frequency Hopping Spread Spectrum (FHSS); FCC certified ISM license-free band; Every data block transmitted is verified (CRC check) and acknowledged by the Base Radio Data Rate: Configurable, 4.8 Kbps, 19.2 Kbps, or 76.8 Kbps. Antenna: Internal 3 omnidirectional, 1/4 wave, monopole of sight. (Actual range may vary depending on site topography.) Probe Input Ranges Probe Type F Range C Range Type L -328 to 1,652 F -200 to 900 C Type J -292 to 1,382 F -180 to 750 C Type K -292 to 2,282 F -180 to 1,250 C Type T -238 to 752 F -150 to 400 C Thermocouple Type U -148 to 1,112 F -100 to 600 C Input Type E -58 to 1,832 F -50 to 1,000 C Type N 32 to 2,192 F 0 to 1,200 C Type S 32 to 2,822 F 0 to 1,550 C Type R 32 to 2,912 F 0 to 1,600 C Type C 32 to 4,208 F 0 to 2,320 C Type B 212 to 3,272 F 100 to 1,800 C Pt100 RTD (DIN ) -328 to 900 F -200 to 482 C Vibration/Shock: Certified per IEC EN (Vibration) and 2-27 (Shock) Random Vibration: Certified to withstand 6Gs, 15 minutes per axis from 9 to 500 Hz CE Compliance: Operates within specifications in fields from 80 to 1000 Mhz with field strengths to 30V/m. Meets EN General Immunity Standard and EN Compatibility Emissions Standard. Environmental Protection: NEMA 4 (Pending) Electrical Classification: CSA and FM rated intrinsically safe for Class I, Div 1, Groups A-D; Class II, Div 1, Groups E-G; Class III, Div 1 (Pending) XYR5000 Wireless Temperature Transmitters (User-Supplied Input) Wireless Temperature Transmitter for RTD Input WT531R $ Wireless Temperature Transmitter for T/C Input WT531T To order a wireless temperature transmitter with an integrated temperature sensor, call Lesman.

5 Illinois, Indiana, Iowa, and SW Michigan The WI550 Analog Input Field Transmitter is part of the XYR5000 family of wireless products. It is used to add wireless capabilities to new or existing analog transmitters, such as pressure, temperature, level, flow meters, ph meters, or any device that has voltage (0 10 V) or current (4 20 ma) outputs. The transmitter combines a high resolution signal conditioner, with a Radio Frequency (RF) transceiver that communicates in a digital protocol, using Frequency Hopping Spread Spectrum (FHSS). FHSS ensures data integrity by continually switching the carrier wave over a wide range of frequencies. Power is supplied by a C size 3.6 V lithium battery, with an expected lifetime of up to five years. The XYR5000 s Smart Response Manager lets the transmitter adapt to changing process conditions, allowing greater visibility to process variation. Smart Response Manager allows the user to set thresholds which, when exceeded, cause the transmitter to adjust sampling and data transmission rates. Two membrane switches on the unit s front allow configuration of: RF Channel Setup: 1 to 16. Baud Rate: 4.8 Kbps, 19.2 Kbps, 76.8 Kbps. RF ID: 1 to 50. Password. Tag Name (up to 21 characters). Normal Transmit Rate: (1 5, 10, 15, 20, or 40 sec, 1 min). Normal Sampling Rate: (1 10, 15, 20, or 30 sec, 1 min). Abnormal Transmit Rate: (1 5, 10, 15, 20, or 40 sec, 1 min). Abnormal Sampling Rate: (1 10, 15, 20, or 30 sec). Analog Input Normal Upper and Lower Values: Disabled/Enabled. Enabled to change Sampling and Transmit rates during abnormal process conditions. Engineering Units: Current model (ma/a); Voltage model (V/mV). Offset: Transmits user-defined offset instead of actual value. Trim: Applies a user-defined one- or two-point correction curve to the actual value. Dimensions XYR5000 Wireless Analog Input Transmitters Specification Performance Accuracy (Linearity and Hysteresis): ±0.1% full scale reading at reference conditions (24 C, 75 F) Ambient Temperature Effect: ±0.01% of reading per C Resolution: 24-bit A/D converter Configuration Panel: 7-digit, high-contrast, anti-reflective monochrome integrated LCD display with membrane switch buttons for local configuration. Display cycles between Input 1, Input 2, and RF status Self-Diagnostics: Self-checking software and hardware that identifies and reports out of spec conditions, and field unit low battery voltage Humidity: 99% RH (non-condensing) Temperature: Ambient Electronics: -40 to 185 F (-40 to 85 C); Display (Full Visibility): -4 to 158 F (-20 to 70 C); Display (Reduced Visibility): -40 to 185 F (-40 to 85 C) Base: Aluminum junction box Electronic Housing: GE Lexan. V0 Rating and UV Stable Wireless Communication: MHz Frequency Hopping Spread Spectrum (FHSS): FCC certified ISM license-free band; Every data block transmitted is verified (CRC check) and acknowledged by the Base Radio. Data Rate: Configurable, 4.8 Kbps, 19.2 Kbps, or 76.8 Kbps Antenna: Internal 3 omnidirectional, 1/4 wave, monopole of sight. (Actual range may vary depending on site topography.) Vibration/Shock: Certified per IEC EN (Vibration) and 2-27 (Shock) Random Vibration: Certified to withstand 6 g s, 15 minutes per axis from 9 to 500 Hz. Electromagnetic Compatibility (CE Compliance): Operates within Specifications in fields from 80 to 1,000 MHz with Field Strengths to 30 V/m. Meets EN General Immunity Standard and EN Compatibility Emissions Standard. Environmental Protection: NEMA 4 (Pending) Electrical Classification: CSA and FM rated intrinsically safe for Class I, Div 1, Groups A-D; Class II, Div 1, Groups E-G; Class III, Div 1 (Pending) XYR5000 Wireless Analog Input Transmitters Wireless Dual Analog Input Interface (4 20 ma) WI551 $ Wireless Dual Analog Input Interface (1 10 V) WI Digital Indicators Controllers and Pressure Transmitters Analytical Instruments

6 Controllers and Digital Indicators Analytical Instruments Pressure Transmitters 6 Illinois, Indiana, Iowa, and SW Michigan XYR5000 Wireless Acoustic Transmitter The WN571 Acoustic Transmitter is part of the XYR5000 family of wireless products. It is used to monitor applications that may generate high frequency noises when they malfunction, such as pressure relief valves, steam traps, and compressor/pumps. The transmitter is acoustically coupled to the monitored equipment, and can be configured to detect abnormal conditions. The transmitter combines a reliable ultrasonic sensor, with a Radio Frequency (RF) transceiver that communicates in a digital protocol, using Frequency Hopping Spread Spectrum (FHSS). FHSS ensures data integrity by continually switching the carrier wave over a wide range of frequencies. Power is supplied by a C size 3.6 V lithium battery, with an expected lifetime of up to five years. The Smart Response Manager allows the transmitter to adapt to changing process conditions, allowing greater visibility to process variation. The Smart Response Manager allows the user to set thresholds which, when exceeded, cause the transmitter to automatically adjust sampling and data transmission rates. Ideal for Steam Trap Leak Monitoring! A typical industrial plant can lose between $100,000 and $150,000 in energy every year just from steam lost in boiler steam traps. Manual leak detection monitoring is too expensive to consider, so plant engineers typically look for an automatic method of identifying leaks in the steam traps. But, signal wiring for an automatic warning system would greatly exceed the cost of the transducers. Steam leaks generate high frequency waves that can be measured by the WN571 wireless acoustic transmitter. Coupled with a base radio, Honeywell s wireless acoustic transmitter can detect steam leaks and report the information back to your control room. They provide reliable leak detection without the need for costly tray and conduit wiring (an average $10 to $40 per foot). A simple investment of just over $3000 for Honeywell wireless instrumentation is easy to justify when you re talking about saving hundreds of thousands of dollars per year! Honeywell Steam Trap Leak Monitoring Solution Wireless Acoustic Transmitter WN571 $ Wireless Base Radio (with Mounting Bracket and RS485 to RS232 Converter WBR-MB,RS $ Total $ Specifications Performance Center Frequency: fc = 40 khz Bandwidth (3dB) RF: 5 khz (fc ±2.5 khz) Data Transmission Technique: Amplitude (8-bit digital output with a scale of 0 to 255) Self-Diagnostics: Self-checking software and hardware that identifies and reports out of spec conditions, and field unit low battery voltage Configuration Panel: 7-digit, high-contrast, anti-reflective monochrome integrated LCD display with membrane switch buttons for local configuration. Display cycles between pressure level and RF status Wireless Communication: 902 MHz 928 MHz Frequency Hopping Spread Spectrum (FHSS); FCC certified ISM license-free band; Every data block transmitted is verified (CRC check) and acknowledged by the Base Radio Data Rate: Configurable: 4.8 Kbps, 19.2 Kbps, or 76.8 Kbps Antenna: Internal 3" omnidirectional, 1/4 wave, monopole of sight. (Actual range may vary depending on site topography. ) Vibration/Shock: Certified per IEC EN (Vibration) and 2-27 (Shock) Random Vibration: Certified to withstand 6 Gs, 15 minutes per axis from 9 to 500 Hz CE Compliance: Operates within Specifications in fields from 80 to 1,000 MHz with Field Strengths to 30 V/m. Meets EN General Immunity Standard and EN Compatibility Emissions Standard Environmental Protection: NEMA 4X (Pending) Electrical Classification: CSA and FM Rated Intrinsically Safe for Class I, Div 1, Groups A D; Class II, Div 1, Groups E G; Class III, Div 1 (Pending) Base Material: Brass and cast aluminum Electronic Housing: GE Lexan. V0 Rating and UV Stable Humidity: 99% RH (non-condensing) Temperature: Ambient Sensor: -40 to 230 F (-40 to 110 C); Ambient Electronics: -40 to 185 F (-40 to 85 C); Process Fluid: -40 to 250 F (-40 to 121 C); Display (Full Visibility): -4 to 158 F (-20 to 70 C); Display (Reduced Visibility): -40 to 185 F (-40 to 85 C) Two membrane switches on the unit s front allow configuration of: RF Channel Setup: 1 to 16. Baud Rate: 4.8 Kbps, 19.2 Kbps, 76.8 Kbps. RF ID: 1 to 50. Password. Tag Name (up to 21 characters). Normal Transmit Rate: (1 5, 10, 15, 20, or 40 sec, 1 min). Normal Sampling Rate: (1 10, 15, 20, or 30 sec, 1 min). Abnormal Transmit Rate: (1 5, 10, 15, 20, or 40 sec, 1 min). Abnormal Sampling Rate: (1 10, 15, 20, or 30 sec). Ultrasonic Normal Upper and Lower Values: Disabled/Enabled. Enabled to change Sampling and Transmit rates during abnormal process conditions. Temperature Normal Upper and Lower Values: Disabled/ Enabled. Enabled to change Sampling and Transmit rates during abnormal process conditions. XYR5000 Wireless Acoustic Signal Transmitters Wireless Acoustic Signal Transmitter WN570 $

7 Illinois, Indiana, Iowa, and SW Michigan The Wireless Base Radio (WBR) is part of the XYR5000 family of wireless products. It combines an RF transceiver with the interface to your existing SCADA, DCS, or data acquisition device. The WBR Radio Frequency (RF) transceiver communicates in a digital protocol, using Frequency Hopping Spread Spectrum (FHSS). FHSS ensures data integrity by continually switching the carrier wave over a wide range of frequencies. Each wireless base radio can communicate with up to 50 field units. As part of its diagnostic capability, the wireless base radio can identify and report field unit out of spec conditions, and low battery alarms. Multiple outputs are available. The wireless base radio is easily configured using the local pushbuttons and display. Ordering Instructions Select as many options as necessary, separated by commas, plus the number of analog outputs needed. A finished catalog number looks like this: WBR-,,A2 XYR5000 Wireless Base Radio Dual Output Wireless Base Radio Unit WBR- $ " Pipe Mounting Bracket MB Options DIN-Rail Mount Power Supply 120/240 VAC to 24 VDC/15W PW RS485 to RS232 External Converter RS Analog Outputs A Analog Outputs A Analog Outputs A DIN-Rail Mount 16 Analog Outputs A Quad 4 20 ma 20 Analog Outputs A Output Module 24 Analog Outputs A Analog Outputs A (Select Option 32 Analog Outputs A Based on the 36 Analog Outputs A Number of 40 Analog Outputs AA Outputs Required) 44 Analog Outputs AB Analog Outputs AC The Site Survey To guarantee wireless link performance in your plant, Honeywell requires that we complete a site survey before the sale. You ll order a site survey based on the number of measurement points in your wireless network configuration. Our Honeywell-certified technician will bring equipment to your plant and replicate the installation you plan to order. He ll check the average distance between transmitters and the base radio, test all the types of components you want to use, and look for potential obstructions to the configuration. Mandatory Site Survey/Applicability Study Fewer than 10 Points SVC11 Measurement 10 to 19 Points SVC12 Call Points to 20 to 29 Points SVC13 Lesman Evaluate 30 to 39 Points SVC14 for 40 to 49 Points SVC15 Pricing 50 or More Points SVC16 XYR5000 Wireless Base Radio Unit A complete XYR5000 wireless system includes: WBR wireless base radio: one base radio per every 50 communicating field units, with the corresponding number of quad analog output modules for 4 20 ma outputs as needed. Wireless management toolkit software: single user license to run the RF server, configuration, and management tools. Any combination of the following: WI550 analog input field transmitter (for 4 20 ma or 1 10V signals); WT530 temperature transmitter for thermocouples and Pt100Ω RTDs; WG510 gauge pressure or WA510 absolute pressure transmitters. Specifications Wireless Communication: MHz Frequency Hopping Spread Spectrum (FHSS); FCC certified ISM license-free band.; Every data block transmitted is verified (CRC check) and acknowledged by the Base Radio Data Rate: Configurable, 4.8 Kbps, 19.2 Kbps, or 76.8 Kbps Scan Rate: Kbps, Kbps, Kbps Antenna: External 3" omnidirectional, 1/2 wave, dipole of sight. (Actual range may vary depending on site topography.) Self-Diagnostics: Self-checking software and hardware that identifies and reports out of spec conditions, and field unit low battery voltage Configuration Panel: Integrated LCD display with membrane switch buttons for local configuration. LCD display is 7-digit (alternating) high contrast, anti-reflective monochrome. Display cycles between field unit status and RF status RF Channel Setup: 1 to 16 Field Device Baud Rate: 4.8 Kbps, 19.2 Kbps, 76.8 Kbps Serial Output: 9.6 Kbps, 19.2 Kbps, 38.4 Kbps, 57.6 Kbps, 115 Kbps Number of Field Units: 1 to 50 Output: RS-485: Up to 3000 feet, maximum number of drops: 15, measured at 19.2 Kbps baud rate; 4 20 ma: Analog output via Quad output modules; RS-232: Optional converter required. Humidity: 99% RH (non-condensing). Temperature: Ambient Electronics: -40 to 185 F (-40 to 85 C); Display (Full Visibility): -4 to 158 F (-20 to 70 C); Display (Reduced Visibility): -40 to 185 F (-40 to 85 C) Electrical Power Connection: Two terminals, 22 AWG power supply wire (GND, 24V). Signal Connection: Two terminals, use 2 wire shielded and protected 16 AWG. Additional two terminals are supplied for linking base radios. Grounding: Earth grounding required. Power Supply: External Supply Voltage, A. DIN rail mounted 120/240 VAC adapter (optional). Electronic Housing: Baked enamel aluminum housing Conduit Connection: 3/4 NPTF Mounting: Wall mount standard, or 2 pipe mounting bracket optional Environmental Protection: NEMA 4X (pending), NEMA 7 (pending) 7 Digital Indicators Controllers and Pressure Transmitters Analytical Instruments

8 Controllers and Digital Indicators Analytical Instruments Pressure Transmitters 8 Illinois, Indiana, Iowa, and SW Michigan XYR5000 Wireless Management Toolkit The Wireless Management Toolkit is part of the XYR5000 family of wireless products. This toolkit is the services management software for the Wireless product family. Services management includes XYR5000 component management (such as configuring the quad analog output modules and field unit threshold settings), process monitoring in real time, and data acquisition. The software can be run on multiple computers at once, so you can view and manage the wireless system from anywhere on your plant network. The computer that connects directly to the base radio network runs in Server mode; other connected computers run as clients. Other than the connection to the base radio, the client and server computers can perform the same configuration, monitoring, and management tasks. The software provides multiple levels of access control (Administrator, Read/Write, and Read-Only). An event log is maintained to track configuration changes. Wireless transmitter data graphs (above) show the current and all past data that is available in the Wireless Transmitter Database. The upper graph is the primary process variable, and the lower graph is the secondary process variable. Graphs can also be specified to show a userselectable data range. The field unit status box shows the time of the last update received from the wireless transmitter. All other information contained within the status box is specific to the time of the previous update. The green OK messages will change to red exclamation points if the respective status reading is in concern, or if either of the process values is above alarm threshold. All process value points are shown in blue if they are below the userselected alarm threshold (indicated by a red line). Any data points exceeding the alarm threshold appear in red. Data graphs can be panned and zoomed via the control buttons located below the graphs. The alarm thresholds refer to alarm setpoints that have been set in the software to warn the user of important changes in the process values. There are four alarm thresholds available for a single process variable unit, and two alarm thresholds available for a dual process variable unit. Alarm thresholds are set through the software configuration menu. The alarms menu lets you select a threshold value and whether above or below this threshold is an alarm. You can also select a time deadband on an alarm threshold, so that once a threshold is exceeded, the system waits a period of time before any alarm is triggered. Software Features Fault and Performance Management Field Unit Groups Field Unit View: Tag Number [up to 21 characters], Monitored Asset, Unit ID, Device Type, Status Field Unit Status View: OK, Threshold Alert, RF Failure, Low Battery Base Radio View: Tag Number [up to 21 characters], Serial Number, RS-485 Address, Number of Field Units, 4 20 ma Output, Status Output Devices Configuration Management (Field Unit Variables) Sensor Sampling: Heartbeat, Normal, Thresholds Thresholds: High/Low Thresholds, Custom Threshold Message Reporting and Analysis Database values contain the asset conditions over time. Data can be exported to perform analysis and create reports. Export data formats: Text (.txt) or Comma Separate Values (.csv) System Requirements PC with 300 MHz or higher processor clock speed recommended. Intel Pentium/Celeron Family, or AMD K6/Athlon/Duron Family, or compatible processor recommended Microsoft Windows 98 SE, 2000, or XP Operating System 256 MB of RAM or higher recommended 10 GB file storage if the database is installed on the local PC RS-485 port or RS-232 serial port Super VGA (800 X 600) or higher-resolution video adapter Monitor, CD-ROM, keyboard, mouse or compatible pointing device XYR5000 Wireless Management Toolkit Configuration and Data Analysis Software for XYR5000 Wireless Devices WMSW1 $