И М. 2 24VAC 50/60Hz, 24-48VDC VAC 50/60Hz

Size: px

Start display at page:

Download "И М. 2 24VAC 50/60Hz, 24-48VDC VAC 50/60Hz"

Veronica Martin
5 years ago
Views:

8 Pin Plug Type DIN W48 H48mm 8 Pin Plug Features Upgraded counting speed: 1cps / 3cps / kcps / 5kcps Selectable voltage input (PNP) method or no-voltage input () method Decimal point setting (fixed

value Built-in Microprocessor Please read Safety considerations in operation manual before using.

1 8 Pin Plug Type DIN W48 H48mm 8 Pin Plug Features Upgraded counting speed: 1cps / 3cps / kcps / 5kcps Selectable voltage input (PNP) method or no-voltage input () method Decimal point setting (fixed decimal point of display) Wide range of power supply : 1-4VAC 5/6Hz, 4VAC 5/6Hz, 4-48VDC universal Memory protection for 1years (using non-volatile semiconductor) Selectable Up/Down for counting value Built-in Microprocessor Please read Safety considerations in operation manual before using. Ordering Information FS 4 1P 4 Specifications supply И М 4VAC 5/6Hz, 4-48VDC 4 1-4VAC 5/6Hz 1P 1-stage setting 출력회로의수 I Indicator digit (4-digit) (5-digit) Item FS 8-pin plug counter Sockets (PG-8, PS-8) are sold separately. Shaded parts( ) are changed and added functions from previous FS Series. Model 1-stage setting FS4-1P FS4-1P4 - Indicator - - FS5-I4 digit 4-digit 5-digit Character size (W H) mm 4 8mm supply 4VAC~ 5/6Hz, 4-48VDCЗ 1-4VAC~ 5/6Hz Permissible voltage range 9 to 11% of rated voltage consumption Max. 3.5VA (4VAC~ 5/6Hz), Max. 4.6VA Max. 3.8VA Max..3W (4-48VDCЗ) (1-4VAC~ 5/6Hz) (1-4VAC~ 5/6Hz) for Selectable 1cps/3cps/kcps/5kcps (DIP switch) Return time Max. 5ms Min. signal width : approx. ms Selectable voltage input (PNP) method or no-voltage input () method Input method [Voltage input (PNP) method]-input impedance: max. 1.8kΩ, [H]: 5-3VDCЗ, [L]: -VDC [No-voltage input () method]-short-circuit impedance: max. 47Ω, short-circuit residual voltage: max. 1VDC, open-circuit impedance: min. 1kΩ One-shot output time.5 to 5 sec Control Type Instantaneous SPST (1a) Contact output Capacity 5VAC~ 3A resistive load - Relay Mechanical Min. 5,, operations life cycle Electrical Min. 1, operations (5VAC 3A resistive load) Insulation resistance Over 1MΩ (at 5VDC megger) External power supply Max. 1VDCЗ ±1% 5mA Memory retention Approx. 1 years (non-volatile memory) Dielectric strength,vac 5/6Hz for 1 min (between all terminals and case) Noise AC voltage ±kv the square wave noise (pulse width 1μs) by noise simulator immunity AC/DC voltage ±5V the square wave noise (pulse width 1μs) by noise simulator Vibration Mechanical.75mm amplitude at frequency 1 to 55Hz (for 1 min) in each X, Y, Z direction for 1 hour Malfunction.5mm amplitude at frequency 1 to 55Hz (for 1 min) in each X, Y, Z direction for 1 minutes Shock Mechanical 3m/s (approx. 3G) in each X, Y, Z direction for 3 times Malfunction 1m/s (approx. 1G) in each X, Y, Z direction for 3 times Environment Ambient temp. -1 to 55, storage: -5 to 65 Ambient humi. 35 to 85%RH, storage: 35 to 85%RH Protection structure IP (front part, IEC standard) Approval И М Weight 1 Approx. 13g (approx. 9g) Approx. 1g (approx. 8g) 1: The weight includes packaging. The weight in parenthesis is for unit only. Environment resistance is rated at no freezing or condensation. Distribution SSRs / s Mode & s J-59

2 Connections FS4-1P4 PNP 1VDC 5mA FS4-1P PNP 1VDC 5mA FS5-I4 PNP 1VDC 5mA VDC CTACT: 5VAC 3A RESISTIVE LOAD VDC CTACT: 5VAC 3A RESISTIVE LOAD VDC 1-4VAC 5/6Hz 4.6VA 4VAC 5/6Hz 3.5VA 4-48VDC.3W 1-4VAC 5/6Hz 3.8VA Input Connections Voltage input (PNP) Solid-state input (standard sensor: PNP output type sensor) Contact input Counte 1.8kΩ V (PNP output), input part 1.8kΩ V (PNP open collector output) 1.8kΩ V Counting speed : Set as 1 or 3cps No-voltage input () Solid-state input (standard sensor: output type sensor) Contact input V ( output) ( open collector output) Counting speed : Set as 1 or 3cps, input part V V Input & output connections 1VDC PR18-5DN GND Total value of load capacity and current consumption should not be exceed current capacity (max. 1VDC 5mA) SOURCE 6 7 Load Please select proper capacity of load not to exceed contact capacity. Contact capacity: max. 5VAC 3A Contact type: 1a J-6

8 Pin Plug Type Dimensions Nameplate design is changed and rear length is shorten than previous. Bracket 9.1 48 1.3 63.8 1.5 6.7 3.5 (unit: mm) cut-out Min.

5 31 41 Ø5 7 35 s 4 DIP Switch 1 3 4 5 6 1 3 Input logic (, input) (no-voltage input) 1 PNP (voltage input) operation mode N.

3 8 Pin Plug Type Dimensions Nameplate design is changed and rear length is shorten than previous. Bracket (unit: mm) cut-out Min. 65 Min Socket (sold separately) PG PS Distribution SSRs / -Ø Ø s 4 DIP Switch Input logic (, input) (no-voltage input) 1 PNP (voltage input) operation mode N. C (not used) Up/Down mode 1 Input logic (/PNP) 6 SW Factory default 1: Indicator model (FS5-I4) does not have no. 1,, 3 DIP switch of SW for output operation mode setting. Mode & s Up/Down mode Down mode Up mode No memory backup 6 1cps 3cps kcps 5kcps J-61

4 Counting Operation For Indicator (FS5-I4) Up mode Down mode +Max. display value +Max. display value -Max. display value - display is only for F, K, Q, S output operation mode and it cannot be set. Operation Mode One-shot output (.5 to 5 sec) Self-holding output mode (SW) F Up mode Down mode Operation increases or decreases until reset signal input is applied and self-holding output is maintained. N and self-holding output are maintained until reset signal input is applied. C When count-up, counting display value is reset and it counts simultaneously. R is reset after one-shot output time and it counts simultaneously. K increases or decreases until reset signal input is applied. P is maintained while output is. Counting value is internally reset and it counts simultaneously. Q increases or decreases during one-shot output time. S Set one-shot output time by front TIME volume switch. maintains when counting display value is larger or equal than setting value. J-6

5 8 Pin Plug Type Dot For Decimal Point 3 sec RUN mode DP 3 sec mode In run mode, hold the key for over 3 sec, and it enters setting mode [DP]. In setting mode, hold the key for over 3 sec, and it saves the setting and returns to RUN mode. If there is no key input for 6 sec when entering setting mode, it returns to RUN mode Set decimal point by front Proper Usage Reset function Reset After DIP switch setting when cutting off the power, press the front key or supplying the external reset. If reset is not executed, the counter will be working as previous mode. The Reset signal width It is reset perfectly when the reset signal is applied for max. ms regardless of the contact input & solid-state input. 1 Reset input 1: In case of a contact reset, it is reset perfectly if the time of reset signal is applied during min. ms even though chattering occurs. : It can be input the signal of CP1&CP after min. 5ms from closing time of reset signal. power The power 1VDC which is provided to sensor is built in it. Please use it under max. DC5mA. Min. signal width : Please make duty ratio (/) 1:1. 1cps: Min..5sec : Min. signal width 3cps: Min.16.7ms kcps: Min..5ms 5kcps: Min..1ms Detaching Case Push the grooves at both side of the unit with a flat head driver to the outside and push the plug part to the front. The plug is detached. Be sure not to be wounded when using a tool. This is a response speed per 1 sec when the duty ratio (:) of input signal is 1:1. If the duty ratio is not 1:1, the width between and should be over min. signal width and the response speed is getting slower against input signal. If either or signal is shorter than minimum signal width, this product may not respond. Ta Tb 3 Ta Therefore Ta ( width) and Tb ( width) needed to be over min. signal width. is 1/ value of rated spec. when duty ratio is 1:3. It can not respond if it is smaller than min. signal width (Ta). In case of 4VAC, 4-48VDC model, power supply should be insulated and limited voltage/current or Class, SELV power supply device. The inner circuit voltage rises within 1ms after supplying the power to the unit. The input may be unavailable at this period. Be sure that the inner circuit voltage drops within 5ms after turning the power. Error Error Troubleshooting ERR value is. Change the setting value anything but. If error occurs, the output turns. Indicator model does not have error display function. 1ms Unstable time for input signal 5ms Use the unit within the rated power supply. When supplying or cutting the power, use a switch not to occur chattering. Distribution SSRs / s Mode & s Push the plug to the front. Turn the power before detaching the case. J-63

Indicator (4digit) (5digit) 8-pin plug counter

Indicator (4digit) (5digit) 8-pin plug counter 8 Pin Plug type DIN W8 H8mm 8 Pin plug counter Features Upgraded counting speed : 1cps / cps / 2kcps / 5kcps Decimal point setting(fixed decimal point of display) Wide range of power : 1-2VAC 5/6Hz 12-2VAC