Draft ETSI EN V ( )

Transcription

1 Draft EN V ( ) HARMONIZED EUROPEAN STANDARD Global System for Mobile communications (GSM); Harmonized EN for mobile stations in the GSM 900 and GSM 1800 bands covering essential requirements under article 3.2 of the R&TTE directive (1999/5/EC)

2 2 Draft EN V ( ) Reference REN/MSG-0018 Keywords cellular, ER-GSM, GSM, mobile, R-GSM 650 Route des Lucioles F Sophia Antipolis Cedex - FRANCE Tel.: Fax: Siret N NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other documents is available at If you find errors in the present document, please send your comment to one of the following services: Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of. The content of the PDF version shall not be modified without the written authorization of. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute All rights reserved. DECT TM, PLUGTESTS TM, UMTS TM and the logo are Trade Marks of registered for the benefit of its Members. 3GPP TM and LTE TM are Trade Marks of registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association.

3 3 Draft EN V ( ) Contents Intellectual Property Rights... 5 Foreword... 5 Modal verbs terminology... 5 Introduction Scope References Normative references Informative references Definitions and abbreviations Definitions Abbreviations Technical requirements specifications Environmental profile Conformance requirements References Transmitter - Frequency error and phase error Transmitter - Frequency error under multipath and interference conditions Transmitter - Frequency error and phase error in HSCSD multislot configuration Frequency error and phase error in GPRS multislot configuration Transmitter output power and burst timing Transmitter - Output RF spectrum Transmitter output power and burst timing in HSCSD multislot configurations Transmitter - Output RF spectrum in HSCSD multislot configuration Transmitter - Output RF spectrum for MS supporting the R-GSM or ER-GSM frequency band Transmitter output power in GPRS multislot configuration Output RF spectrum in GPRS multislot configuration Conducted spurious emissions - MS allocated a channel Conducted spurious emissions - MS in idle mode Conducted spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS allocated a channel Conducted spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS in idle mode Radiated spurious emissions - MS allocated a channel Radiated spurious emissions - MS in idle mode Radiated spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS allocated a channel Radiated spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS in idle mode Receiver Blocking and spurious response - speech channels Receiver Blocking and spurious response - speech channels for MS supporting the R-GSM or ER- GSM frequency band Frequency error and Modulation accuracy in EGPRS Configuration Frequency error under multipath and interference conditions in EGPRS Configuration EGPRS Transmitter output power Output RF spectrum in EGPRS configuration Blocking and spurious response in EGPRS configuration Blocking and spurious response in DLMC configuration Testing for compliance with technical requirements Environmental conditions for testing Interpretation of the measurement results Essential radio test suites Transmitter - Frequency error and phase error... 15

4 4 Draft EN V ( ) Transmitter - Frequency error under multipath and interference conditions Transmitter - Frequency error and phase error in HSCSD multislot configuration Frequency error and phase error in GPRS multislot configuration Transmitter output power and burst timing Transmitter - Output RF spectrum Transmitter output power and burst timing in HSCSD multislot configurations Transmitter - Output RF spectrum in HSCSD multislot configuration Transmitter - Output RF spectrum for MS supporting the R-GSM or ER-GSM frequency band Transmitter output power in GPRS multislot configuration Output RF spectrum in GPRS multislot configuration Conducted spurious emissions - MS allocated a channel Conducted spurious emissions - MS in idle mode Conducted spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS allocated a channel Conducted spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS in idle mode Radiated spurious emissions - MS allocated a channel Radiated spurious emissions - MS in idle mode Radiated spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS allocated a channel Radiated spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS in idle mode Receiver Blocking and spurious response - speech channels Receiver Blocking and spurious response - speech channels for MS supporting the R-GSM or ER- GSM frequency band Frequency error and Modulation accuracy in EGPRS Configuration Frequency error under multipath and interference conditions in EGPRS Configuration EGPRS Transmitter output power Output RF spectrum in EGPRS configuration Blocking and spurious response in EGPRS configuration Blocking and spurious response in DLMC configuration Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) A.1 Test specification table A.2 Type of Mobile Stations A.3 Additional Information Annex B (informative): Change history History... 24

5 5 Draft EN V ( ) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to. The information pertaining to these essential IPRs, if any, is publicly available for members and non-members, and can be found in SR : "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to in respect of standards", which is available from the Secretariat. Latest updates are available on the Web server ( Pursuant to the IPR Policy, no investigation, including IPR searches, has been carried out by. No guarantee can be given as to the existence of other IPRs not referenced in SR (or the updates on the Web server) which are, or may be, or may become, essential to the present document. Foreword This draft Harmonized European Standard (EN) has been produced by Technical Committee Mobile Standards Group (MSG), and is now submitted for the combined Public Enquiry and Vote phase of the standards EN Approval Procedure. The update to version of the present document includes the following major changes: - Inclusion of mobile equipment supporting operation in the ER-GSM 900 band. - Inclusion of mobile equipment supporting operation in Downlink Multi-Carrier mode (DLMC). The present document has been produced by in response to mandate M/284 issued from the European Commission under Council Directive 98/34/EC [i.4] as amended by Directive 98/48/EC [i.8]. The title and reference to the present document are intented to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under Directive 1999/5/EC [i.6]. The requirements relevant to Directive 1999/5/EC [i.6] are summarized in Annex A. Proposed national transposition dates Date of latest announcement of this EN (doa): Date of latest publication of new National Standard or endorsement of this EN (dop/e): Date of withdrawal of any conflicting National Standard (dow): 3 months after publication 6 months after doa 18 months after doa Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in deliverables except when used in direct citation.

6 6 Draft EN V ( ) Introduction The present document is part of a set of standards designed to fit in a modular structure to cover all radio and telecommunications terminal equipment under the R&TTE Directive [i.6]. Each standard is a module in the structure. The modular structure is shown in figure f 3.3e 3.3d 3.3c 3.3b 3.3a Disability* Emergency* Fraud* Privacy* No harm to the network* Interworking via the network* Interworking with the network * If needed Scoped by equipment class or type 3.2 Spectrum Use of spectrum New radio harmonized standards Scoped by frequency and/or equipment type 3.1b EMC Radio Product EMC EN multi-part EMC standard Generic and product standards also notified under EMC Directive 3.1a Safety - If needed, new standards for human exposure to Electromagnetic Fields, - if needed, new standards for acoustic safety Standards also notified under LV Directive Non-radio Radio (RE) TTE Non-TTE Figure 1: Modular structure for the various standards used under the R&TTE Directive [i.6]

7 7 Draft EN V ( ) The left hand edge of the figure 1 shows the different clauses of article 3 of the R&TTE Directive [i.6]. For article 3.3 various horizontal boxes are shown. Dotted lines indicate that at the time of publication of the present document essential requirements in these areas have to be adopted by the Commission. If such essential requirements are adopted, and as far and as long as they are applicable, they will justify individual standards whose scope is likely to be specified by function or interface type. The vertical boxes show the standards under article 3.2 for the use of the radio spectrum by radio equipment. The scopes of these standards are specified either by frequency (normally in the case where frequency bands are harmonized) or by radio equipment type. For article 3.1b the diagram shows EN [i.3], the multi-part product EMC standard for radio used under the EMC Directive [i.1]. For article 3.1a the diagram shows the existing safety standards currently used under the LV Directive [i.2] and new standards covering human exposure to electromagnetic fields. New standards covering acoustic safety may also be required. The bottom of the figure shows the relationship of the standards to radio equipment and telecommunications terminal equipment. A particular equipment may be radio equipment, telecommunications terminal equipment or both. A radio spectrum standard will apply if it is radio equipment. An article 3.3 standard will apply as well only if the relevant essential requirement under the R&TTE Directive [i.6] is adopted by the Commission and if the equipment in question is covered by the scope of the corresponding standard. Thus, depending on the nature of the equipment, the essential requirements under the R&TTE Directive [i.6] may be covered in a set of standards. The modularity principle has been taken because: it minimizes the number of standards needed. Because equipment may, in fact, have multiple interfaces and functions it is not practicable to produce a single standard for each possible combination of functions that may occur in an equipment; it provides scope for standards to be added: - under article 3.2 when new frequency bands are agreed; or - under article 3.3 should the Commission take the necessary decisions without requiring alteration of standards that are already published; it clarifies, simplifies and promotes the usage of Harmonized Standards as the relevant means of conformity assessment.

8 8 Draft EN V ( ) 1 Scope The present document applies to the following radio telecommunications terminal equipment types: - GSM mobile station. This radio equipment type is for operation within the Digital cellular telecommunications system in the GSM 900 and/or GSM 1800 frequency bands as shown in table 1, with a channel separation of 200 khz, utilizing constant envelope modulation and carrying traffic channels according to the Time Division Multiple Access (TDMA) principle. Table 1: Frequency bands for GSM 900 and GSM 1800 Mobile Station system Type TX RX P-GSM MHz to 915 MHz 935 MHz to 960 MHz GSM MHz to MHz MHz to MHz E-GSM MHz to 915 MHz 925 MHz to 960 MHz R-GSM MHz to 915 MHz 921 MHz to 960 MHz ER-GSM MHz to 915 MHz 918 MHz to 960 MHz The present document is intended to cover the provisions of Directive 1999/5/EC (R&TTE Directive) [i.6] article 3.2, which states that ".. radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". The present document covers the general access requirements for terminal equipment up to and including 3GPP Rel-12. The general access requirements, applied to the terminal equipment, are for one release only. The present document does not cover the GPRS Class A mobiles and the ECSD mobiles. For each test purpose and its corresponding conformance requirement, a reference is given to the test method in TS [2]. The requirements apply at the air interface, which may be stimulated to perform the tests by additional equipment if necessary. The measurement uncertainty is described in TS [2], Annex 5. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [i.6] will apply to equipment within the scope of the present document. NOTE 1: A list of such ENs is included on the web site TS [2] constitutes the conformance test suite for GSM. The verification of the conformance requirements in the present document is based on the tests described in this reference. The set of requirements in TS [2] and the set of requirements in the present document need not be identical. Some requirements only apply to specific types of mobile station (e.g. data tests only apply to mobile stations with a data facility, tests that only apply to GSM 900 or only to GSM 1800 or to both). The present document indicates the specific test which should be carried out for each mobile station type. An active accessory is covered by the present document if it modifies the terminal performance in an aspect which affects conformance to essential requirements. NOTE 2: Only active devices are subject to the present document. Accessories may be tested with specific terminals, and either approved for use with those terminals only, or may possibly be approved for use with a wider range of terminals, depending on the nature and effect of the accessory.

9 9 Draft EN V ( ) 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at NOTE: While any hyperlinks included in this clause were valid at the time of publication, cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] Void. [2] TS (V12.2.0) ( ): "Digital cellular telecommunications system (Phase 2+); Mobile Station (MS) conformance specification; Part 1: Conformance specification (3GPP TS version Release 12)". [3] Void. [4] Void. [5] ETS (V5.3.2) ( ): "Digital cellular telecommunications system (Phase 2+) (GSM); Teleservices supported by a GSM Public Land Mobile Network (PLMN) (GSM version 5.3.2)". [6] TS (V6.0.0) ( ): "Digital cellular telecommunications system (Phase 2+) (GSM); Teleservices supported by a GSM Public Land Mobile Network (PLMN) (GSM version Release 1997)". [7] TS (V7.0.0) ( ): "Digital cellular telecommunications system (Phase 2+) (GSM); Teleservices supported by a GSM Public Land Mobile Network (PLMN) (GSM version Release 1998)". [8] TS (V3.3.0) ( ): "Digital cellular telecommunications system (Phase 2+) (GSM); Universal Mobile Telecommunications System (UMTS); Circuit Teleservices supported by a Public Land Mobile Network (PLMN) (3GPP TS version Release 1999)". [9] TS (V4.3.0) ( ): "Digital cellular telecommunications system (Phase 2+) (GSM); Universal Mobile Telecommunications System (UMTS); Circuit Teleservices supported by a Public Land Mobile Network (PLMN) (3GPP TS version Release 4)". [10] Void. [11] Void. [12] TS (V3.5.0) ( ): "Digital cellular telecommunications system (Phase 2+) (GSM); Universal Mobile Telecommunications System (UMTS); General Packet Radio Service (GPRS); Service description; Stage 1 (3GPP TS version Release 1999)". [13] TS (V4.4.0) ( ): "Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); General Packet Radio Service (GPRS); Service description; Stage 1 (3GPP TS version Release 4)". [14] Void. [15] Void.

10 10 Draft EN V ( ) [16] TS (V8.16.0) ( ): "Digital cellular telecommunications system (Phase 2+); General Packet Radio Service (GPRS); Mobile Station (MS) - Base Station System (BSS) interface; Radio Link Control/ Medium Access Control (RLC/MAC) protocol (3GPP TS version Release 1999)". [17] TS (V12.3.0) ( ): "Digital cellular telecommunications system (Phase 2+); General Packet Radio Service (GPRS); Mobile Station (MS) - Base Station System (BSS) interface; Radio Link Control / Medium Access Control (RLC/MAC) protocol (3GPP TS version Release 12)". [18] Void. [19] TS (V5.10.0) ( ): "Digital cellular telecommunications system (Phase 2+); Multiplexing and multiple access on the radio path (3GPP TS version Release 1996)". [20] TS (V6.10.0) ( ): "Digital cellular telecommunications system (Phase 2+); Multiplexing and multiple access on the radio path (3GPP TS version Release 1997)". [21] TS (V7.7.0) ( ): "Digital cellular telecommunications system (Phase 2+); Multiplexing and multiple access on the radio path (3GPP TS version Release 1998)". [22] TS (V8.10.0) ( ): "Digital cellular telecommunications system (Phase 2+); Multiplexing and multiple access on the radio path (3GPP TS version Release 1999)". [23] TS (V4.5.0) ( ): "Digital cellular telecommunications system (Phase 2+); Multiplexing and multiple access on the radio path (3GPP TS version Release 4)". [24] Void. [25] TS (V5.13.0) ( ): "Digital cellular telecommunications system (Phase 2+) (GSM); Radio transmission and reception (3GPP TS version Release 1996)". [26] TS (V6.8.0) ( ): "Digital cellular telecommunications system (Phase 2+); Radio Transmission and Reception (3GPP TS version Release 1997)". [27] TS (V7.9.0) ( ): "Digital cellular telecommunications system (Phase 2+); Radio Transmission and Reception (3GPP TS version Release 1998)". [28] TS (V8.14.0) ( ): "Digital cellular telecommunications system (Phase 2+); Radio Transmission and Reception (3GPP TS version Release 1999)". [29] TS (V12.4.0) ( ): "Digital cellular telecommunications system (Phase 2+); Radio transmission and reception (3GPP TS version Release 12)". [30] TR (V12.0.0) ( ): "Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; Vocabulary for 3GPP Specifications (3GPP TR version Release 12)". 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Council Directive 89/336/EEC of 3 May 1989 on the approximation of the laws of the Member States relating to electromagnetic compatibility (EMC Directive).

11 11 Draft EN V ( ) [i.2] [i.3] [i.4] [i.5] [i.6] [i.7] [i.8] Council Directive 73/23/EEC of 19 February 1973 on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (LV Directive). EN (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services". Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations. Void. Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R&TTE Directive). TR (all parts) (V1.4.1) ( ): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics". Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending Directive 98/34/EC laying down a procedure for the provision of information in the field of technical standards and regulations. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in TR [30] and the following apply: EGPRS: any subset of the packet traffic channels PDTCH/MCS-1 to MCS-9 and related control channels E-GSM: extended GSM 900 band (includes P-GSM band) environmental profile: range of environmental conditions under which equipment within the scope of the present document is required to comply with the provisions of the present document ER-GSM 900: extended Railway GSM 900 band (includes R-GSM band) GPRS: any subset of the packet traffic channels PDTCH/CS-1 to CS-4 and related control channels GSM 900: unless otherwise specified, references to GSM 900 include P-GSM, E-GSM and R-GSM band GSM: unless otherwise specified, references to GSM include GSM 400, GSM 900, ER-GSM 900 and DCS 1800 P-GSM: primary GSM 900 band R-GSM: Railways GSM 900 band (includes P-GSM band and E-GSM band)

12 12 Draft EN V ( ) 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: DLMC ECSD EGPRS GPRS HSCSD MS R&TTE RF TDMA Downlink Multi-Carrier Enhanced Circuit Switched Data Enhanced GPRS General Packet Radio Service High Speed Circuit Switched Data Mobile Station which includes a GSM radio part Radio and Telecommunications Terminal Equipment Radio Frequency Time Division Multiple Access 4 Technical requirements specifications 4.1 Environmental profile The technical requirements of the present document apply under the environmental profile for operation of the equipment, which shall be declared by the supplier. The equipment shall comply with all the technical requirements of the present document at all times when operating within the boundary limits of the required operational environmental profile. 4.2 Conformance requirements References The present document contains all requirements that are needed for terminals to meet the essential requirement as defined in the Directive 1999/5/EC [i.6], article The present document gives normative reference to a clause of TS [2] containing the conformance requirement text and references to the base standard Transmitter - Frequency error and phase error Clauses and of TS [2] shall apply Transmitter - Frequency error under multipath and interference conditions Clauses and of TS [2] shall apply Transmitter - Frequency error and phase error in HSCSD multislot configuration Clauses and of TS [2] shall apply Frequency error and phase error in GPRS multislot configuration Clauses and of TS [2] shall apply Transmitter output power and burst timing Clauses and of TS [2] shall apply.

13 13 Draft EN V ( ) Transmitter - Output RF spectrum Clauses and of TS [2] shall apply Transmitter output power and burst timing in HSCSD multislot configurations Clauses and of TS [2] shall apply Transmitter - Output RF spectrum in HSCSD multislot configuration Clauses and of TS [2] shall apply Transmitter - Output RF spectrum for MS supporting the R-GSM or ER-GSM frequency band Clauses and of TS [2] shall apply Transmitter output power in GPRS multislot configuration Clauses and of TS [2] shall apply Output RF spectrum in GPRS multislot configuration Clauses and of TS [2] shall apply Conducted spurious emissions - MS allocated a channel Clauses and of TS [2] shall apply Conducted spurious emissions - MS in idle mode Clauses and of TS [2] shall apply Conducted spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS allocated a channel Clauses and of TS [2] shall apply Conducted spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS in idle mode Clauses and of TS [2] shall apply Radiated spurious emissions - MS allocated a channel Clauses and of TS [2] shall apply Radiated spurious emissions - MS in idle mode Clauses and of TS [2] shall apply.

14 14 Draft EN V ( ) Radiated spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS allocated a channel Clauses and of TS [2] shall apply Radiated spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS in idle mode Clauses and of TS [2] shall apply Receiver Blocking and spurious response - speech channels Clauses and of TS [2] shall apply Receiver Blocking and spurious response - speech channels for MS supporting the R-GSM or ER-GSM frequency band Clauses and of TS [2] shall apply Frequency error and Modulation accuracy in EGPRS Configuration Clauses and of TS [2] shall apply Frequency error under multipath and interference conditions in EGPRS Configuration Clauses and of TS [2] shall apply EGPRS Transmitter output power Clauses and of TS [2] shall apply Output RF spectrum in EGPRS configuration Clauses and of TS [2] shall apply Blocking and spurious response in EGPRS configuration Clauses and of TS [2] shall apply Blocking and spurious response in DLMC configuration Clauses b.1 and b.2 of TS [2] shall apply. 5 Testing for compliance with technical requirements 5.1 Environmental conditions for testing Tests defined in the present document shall be carried out at representative points within the boundary limits of the declared operational environmental profile.

15 15 Draft EN V ( ) Where technical performance varies subject to environmental conditions, tests shall be carried out under a sufficient variety of environmental conditions (within the boundary limits of the declared operational environmental profile) to give confidence of compliance for the affected technical requirements. 5.2 Interpretation of the measurement results The interpretation of the results recorded in a test report for the measurements described in the present document shall be as follows: the measured value related to the corresponding limit will be used to decide whether an equipment meets the requirements of the present document; the value of the measurement uncertainty for the measurement of each parameter shall be included in the test report; the recorded value of the measurement uncertainty shall be, for each measurement, equal to or lower than the one specified in Annex 5 of TS [2]. For the test methods, according to the present document, the measurement uncertainty figures shall be calculated and shall correspond to an expansion factor (coverage factor) k = 1,96 (which provides confidence levels of 95 % in the case where the distributions characterizing the actual measurement uncertainties are normal (Gaussian)). Principles for the calculation of measurement uncertainty are contained in TR [i.7], in particular in Annex D of TR [i.7]. 5.3 Essential radio test suites Transmitter - Frequency error and phase error Requirements of TS [2], clause shall be fulfilled Transmitter - Frequency error under multipath and interference conditions Requirements of TS [2], clause shall be fulfilled Transmitter - Frequency error and phase error in HSCSD multislot configuration Requirements of TS [2], clause shall be fulfilled Frequency error and phase error in GPRS multislot configuration Requirements of TS [2], clause shall be fulfilled Transmitter output power and burst timing Requirements of TS [2], clause shall be fulfilled Transmitter - Output RF spectrum Requirements of TS [2], clause shall be fulfilled Transmitter output power and burst timing in HSCSD multislot configurations Requirements of TS [2], clause shall be fulfilled.

16 16 Draft EN V ( ) Transmitter - Output RF spectrum in HSCSD multislot configuration Requirements of TS [2], clause shall be fulfilled Transmitter - Output RF spectrum for MS supporting the R-GSM or ER-GSM frequency band Requirements of TS [2], clause shall be fulfilled Transmitter output power in GPRS multislot configuration Requirements of TS [2], clause shall be fulfilled Output RF spectrum in GPRS multislot configuration Requirements of TS [2], clause shall be fulfilled Conducted spurious emissions - MS allocated a channel Requirements of TS [2], clause shall be fulfilled Conducted spurious emissions - MS in idle mode Requirements of TS [2], clause shall be fulfilled Conducted spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS allocated a channel Requirements of TS [2], clause shall be fulfilled Conducted spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS in idle mode Requirements of TS [2], clause shall be fulfilled Radiated spurious emissions - MS allocated a channel Requirements of TS [2], clause shall be fulfilled Radiated spurious emissions - MS in idle mode Requirements of TS [2], clause shall be fulfilled Radiated spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS allocated a channel Requirements of TS [2], clause shall be fulfilled Radiated spurious emissions for MS supporting the R-GSM or ER-GSM frequency band - MS in idle mode Requirements of TS [2], clause shall be fulfilled.

17 17 Draft EN V ( ) Receiver Blocking and spurious response - speech channels Requirements of TS [2], clause shall be fulfilled Receiver Blocking and spurious response - speech channels for MS supporting the R-GSM or ER-GSM frequency band Requirements of TS [2], clause shall be fulfilled Frequency error and Modulation accuracy in EGPRS Configuration Requirements of TS [2], clause shall be fulfilled Frequency error under multipath and interference conditions in EGPRS Configuration Requirements of TS [2], clause shall be fulfilled EGPRS Transmitter output power Requirements of TS [2], clause shall be fulfilled Output RF spectrum in EGPRS configuration Requirements of TS [2], clause shall be fulfilled Blocking and spurious response in EGPRS configuration Requirements of TS [2], clause shall be fulfilled Blocking and spurious response in DLMC configuration Requirements of TS [2], clause b.5 shall be fulfilled.

18 18 Draft EN V ( ) Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) A.1 Test specification table The HS Requirements and conformance Test specifications Table (HS-RTT) in table A.1 serves a number of purposes, as follows: it provides a statement of all the requirements in words and by cross reference to (a) specific clause(s) in the present document or to (a) specific clause(s) in (a) specific referenced document(s); it provides a statement of all the test procedures corresponding to those requirements by cross reference to (a) specific clause(s) in the present document or to (a) specific clause(s) in (a) specific referenced document(s); it qualifies each requirement to be either: - Unconditional: meaning that the requirement applies in all circumstances; or - Conditional: meaning that the requirement is dependent on the manufacturer having chosen to support optional functionality defined within the schedule. in the case of Conditional requirements, it associates the requirement with the particular optional service or functionality; it qualifies each test procedure to be either: - Essential: meaning that it is included with the Essential Radio Test Suite and therefore the requirement shall be demonstrated to be met in accordance with the referenced procedures; - Other: meaning that the test procedure is illustrative but other means of demonstrating compliance with the requirement are permitted. Table A.1: HS Requirements and conformance Test specifications Table (HS-RTT) Harmonized Standard EN The following requirements and test specifications are relevant to the presumption of conformity under the article 3.2 of the R&TTE Directive [i.6] Requirement Requirement Conditionality Test Specification No Description Reference: Clause No U/C Condition E/O Reference: Clause No 1 Transmitter U E 13.1 Frequency error and phase error 2 Transmitter - Frequency error under multipath and interference conditions U E Transmitter - Frequency error and phase error in HSCSD multislot configuration 4 Frequency error and phase error in GPRS multislot configuration C For all HSCSD multislot MS (as defined in table A.2) C For all GPRS multislot MS (as defined in table A.2) E 13.6 E

19 19 Draft EN V ( ) Harmonized Standard EN The following requirements and test specifications are relevant to the presumption of conformity under the article 3.2 of the R&TTE Directive [i.6] Requirement Requirement Conditionality Test Specification No Description Reference: Clause No U/C Condition E/O Reference: Clause No 5 Transmitter output power and burst timing U E Transmitter - Output RF spectrum 7 Transmitter output power and burst timing in HSCSD multislot configurations 8 Transmitter - Output RF spectrum in HSCSD multislot configuration 9 Transmitter Output RF spectrum for MS supporting the R- GSM or ER-GSM frequency band 10 Transmitter output power in GPRS multislot configuration 11 Output RF spectrum in GPRS multislot configuration 12 Conducted spurious emissions - MS allocated a channel 13 Conducted spurious emissions - MS in idle mode 14 Conducted spurious emissions for MS supporting the R- GSM or ER-GSM frequency band - MS allocated a channel 15 Conducted spurious emissions for MS supporting the R- GSM or ER-GSM frequency band - MS in idle mode 16 Radiated spurious emissions - MS allocated a channel 17 Radiated spurious emissions - MS in idle mode 18 Radiated spurious emissions for MS supporting the R- GSM or ER-GSM frequency band - MS allocated a channel C For all MS except R-GSM or ER-GSM MS (as defined in table A.2) C For all HSCSD multislot MS (as defined in table A.2) C For all HSCSD multislot MS (as defined in table A.2) C For all R-GSM or ER-GSM MS (as defined in table A.2) C For all GPRS multislot MS (as defined in table A.2) C For all GPRS multislot MS (as defined in table A.2) C For all MS with a Permanent Antenna Connector except R-GSM or ER-GSM MS (as defined in tables A.2 and A.3) C For all MS with a Permanent Antenna Connector except R-GSM or ER-GSM MS (as defined in tables A.2 and A.3) C For all R-GSM or ER-GSM MS with a Permanent Antenna Connector (as defined in tables A.2 and A.3) C For all R-GSM or ER-GSM MS - with a Permanent Antenna Connector (as defined in tables A.2 and A.3) C For all MS except R-GSM or ER-GSM MS (as defined in table A.2) C For all MS except R-GSM or ER-GSM MS (as defined in table A.2) C For all R-GSM or ER-GSM MS (as defined in table A.2) E 13.4 E 13.7 E 13.8 E 13.9 E E E E E E E E E

20 20 Draft EN V ( ) Harmonized Standard EN The following requirements and test specifications are relevant to the presumption of conformity under the article 3.2 of the R&TTE Directive [i.6] Requirement Requirement Conditionality Test Specification No Description Reference: Clause No U/C Condition E/O Reference: Clause No 19 Radiated spurious emissions for MS supporting the R- GSM or ER-GSM frequency band - MS in idle mode 20 Receiver Blocking and spurious response - speech channels 21 Receiver Blocking and spurious response - speech channels for MS supporting the R-GSM or ER-GSM frequency band 22 Frequency error and Modulation accuracy in EGPRS Configuration 23 Frequency error under multipath and interference conditions in EGPRS Configuration 24 EGPRS Transmitter output power 25 Output RF spectrum in EGPRS configuration 26 Blocking and spurious response in EGPRS configuration 27 Blocking and spurious response in DLMC configuration C For all R-GSM or ER-GSM MS (as defined in table A.2) C For all MS supporting Telephony Service except R- GSM or ER-GSM MS (as defined in tables A.2 and A.3) C For all R-GSM or ER-GSM MS supporting Telephony Service (as defined in tables A.2 and A.3) C For all EGPRS 8PSK Uplink capable MS (as defined in table A.2) C For all EGPRS MS (as defined in table A.2) C For all EGPRS 8PSK Uplink capable MS (as defined in table A.2) C For all EGPRS 8PSK Uplink capable MS (as defined in table A.2) C For all EGPRS MS (as defined in table A.2) C For all DLMC MS (as defined in table A.2) E E E E E E E E E b Key to columns: Requirement: No Description Clause Number A unique identifier for one row of the table which may be used to identify a requirement or its test specification. A textual reference to the requirement. Identification of clause(s) defining the requirement in the present document unless another document is referenced explicitly. Requirement Conditionality: U/C Condition Indicates whether the requirement is to be unconditionally applicable (U) or is conditional upon the manufacturers claimed functionality of the equipment (C). Explains the conditions when the requirement shall or shall not be applicable for a requirement which is classified "conditional".

21 21 Draft EN V ( ) Test Specification: E/O NOTE: Indicates whether the test specification forms part of the Essential Radio Test Suite (E) or whether it is one of the Other Test Suite (O). All tests whether "E" or "O" are relevant to the requirements. Rows designated "E" collectively make up the Essential Radio Test Suite; those designated "O" make up the Other Test Suite; for those designated "X" there is no test specified corresponding to the requirement. The completion of all tests classified "E" as specified with satisfactory outcomes is a necessary condition for a presumption of conformity. Compliance with requirements associated with tests classified "O" or "X" is a necessary condition for presumption of conformity, although conformance with the requirement may be claimed by an equivalent test or by manufacturer's assertion supported by appropriate entries in the technical construction file. Clause Number Identification of clause(s) defining the test specification in the present document unless another document is referenced explicitly. Where no test is specified (that is, where the previous field is "X") this field remains blank. A.2 Type of Mobile Stations Table A.2: Type of Mobile Station Item Type of Mobile Station Ref. Status Support Mnemonic 1 HSCSD Multislot MS TS [19] O Type_HSCSD_Multislot to [22], clause B.1; TS [23], clause B.1 2 R-GSM MS TS [25] O Type_R-GSM to [28], clause 2; TS [29], clause 2 3 Support of GPRS Multislot TS [20] O Type_GPRS_Multislot_uplink class on the uplink to [22], clause B.1; TS [23], clause B.1 4 EGPRS TS [12] O Type_EGPRS 5 EGPRS capable of 8PSK in Uplink, of all Multislot classes and [13] TS [16], clause a; TS [17], clause a 6 ER-GSM MS TS [29], clause 2 7 DLMC MS TS [17], clause 5 O O O Type_EGPRS_8PSK_uplink Type_ER-GSM Type_DLMC Key to columns: No A unique identifier for one row of the table which may be used to identify a requirement or its test specification. Type of Mobile station A textual definition of the Mobile station. Status Status of the entry as follows: M O O.<n> Mandatory, shall be implemented under all circumstances; Optional, may be provided, but if provided shall be implemented in accordance with the requirements; this status is used for mutually exclusive or selectable options among a set. The integer "n" shall refer to a unique group of options within the EN-RT. A footnote to the EN-RT shall explicitly state what the requirement is for each numbered group. For example, "It is mandatory to support at least one of these options", or, "It is mandatory to support exactly one of these options".

22 22 Draft EN V ( ) C<n> N/A X Mnemonic Conditional number <n>. Reference is made to a Boolean expression under the table with predicates of support answers, which will resolve to either "M", "X", "N", or "O.<n>" for a specific implementation. In all cases "ELSE Not Applicable" is implied, if an ELSE expression is omitted. Expressions such a A.x/y refer to item "y" in table A.x. Not applicable. Excluded or Prohibited. Mnemonic identifiers for each item. A.3 Additional Information Table A.3: Additional information Item Additional Information Ref. Status Support Mnemonic 1 Telephony. ETS [5], O TSPC_Serv_TS11 clause A.1.1; TS [6] and [7], clause A.1.1; TS [8] and [9], clause A Permanent Antenna Connector. TS [2], clauses and O TSPC_AddInfo_PermAntenna Key to columns: No A unique identifier for one row of the table which may be used to identify a requirement or its test specification. Additional Information A textual definition of the Mobile station. Status Status of the entry as follows: M O O.<n> C<n> N/A X Mnemonic Mandatory, shall be implemented under all circumstances; Optional, may be provided, but if provided shall be implemented in accordance with the requirements; this status is used for mutually exclusive or selectable options among a set. The integer "n" shall refer to a unique group of options within the EN-RT. A footnote to the EN-RT shall explicitly state what the requirement is for each numbered group. For example, "It is mandatory to support at least one of these options", or, "It is mandatory to support exactly one of these options"; Conditional number <n>. Reference is made to a Boolean expression under the table with predicates of support answers, which will resolve to either "M", "X", "N", or "O.<n>" for a specific implementation. In all cases "ELSE Not Applicable" is implied, if an ELSE expression is omitted. Expressions such a A.x/y refer to item "y" in table A.x; Not applicable; Excluded or Prohibited. Mnemonic identifiers for each item.

23 23 Draft EN V ( ) Annex B (informative): Change history Date Version Comments February Presented at SMG #28 for information August Changes approved at SMG7 #22 September Adapted to R&TTE Steering Committee HS proforma January Selection of test cases for Phase 2. Addition of sections for Phase 2+. Phase 2+ test cases are for further study February Editorial reorganization to comply with proforma and with latest proforma sentences by STF 149 April References update and editorial modifications May Edited during SMG7#25 June Electronically approved by SMG7 June Presented for approval at SMG #32 June Approved at SMG #32 December Update to Version for Publication September Update to Version for MSG Approval. All requirements up to and including Rel-4 requirements are included October Approval at MSG #5 June _9.1.0 Early draft presented at MSG#40 adding ER-GSM October _9.1.2 New draft based on latest HS skeleton presented at MSG#41 December _9.1.3 New draft based on EditHelp inputs

24 24 Draft EN V ( ) History Document history V7.0.1 December 2000 Publication V9.0.2 March 2003 Publication V February 2015 EN Approval Procedure AP : to