SPORTON FCCC RF APPLICANT EQUIPMENT BRAND NAME MODEL NAME FCC ID STANDARDD ZTE : N9518. The product was. received on. not be.

Transcription

1 FCC RF Test Report FCCC RF Test Report APPLICANT EQUIPMENT BRAND NAME MODEL NAME FCC ID STANDARDD CLASSIFICATION : ZTE CORPORATION : CDMA/ /LTE Multi-Mode Digital Mobile Phone ZTE : N9518 : SRQ-ZTEN9518 : FCC 477 CFR Part 2, and 90(S) : PCS Licensed Transmitterr Held to Ear (PCE) The product was received on Mar. 30, 2015 and testing was completed onn Apr. 20, We, SPORTON INTERNATIONAL (SHENZHEN) INC., would like to declare d that the tested sample has been evaluated in accordance with the procedures given in ANSI / TIAA / EIA-603-C-2004 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL (SHENZHEN) INC., reproduced except in full. the test report shall not be Reviewed by: Joseph Lin / Supervisor Approved by: Jones Tsai / Manager SPORTON INTERNATIONAL (KUNSHAN) INC. No. 3-2, PingXiangg Road, Kunshan, Jiangsu Province, P.. R. China SPORTON INTERNATIONAL (KUNSHAN) INC. TEL : FAX : Page Number : 1 of o 30 Report Issued Date : May 11, 2015 Report Version : Rev. 01

2 TABLE OF CONTENTS REVISION HISTORY... 3 SUMMARY OF TEST RESULT GENERAL DESCRIPTION Applicant Manufacturer Feature of Equipment Under Test Product Specification of Equipment Under Test Modification of EUT Maximum Frequency Tolerance and Emission Designator Testing Site Applied Standards TEST CONFIGURATION OF EQUIPMENT UNDER TEST Test Mode Connection Diagram of Test System Support Unit used in test configuration and system Measurement Results Explanation Example TEST RESULT Conducted Output Power Measurement % Occupied Bandwidth and 26dB Bandwidth Measurement Emissions Mask Measurement Emissions Mask Out Of Band Emissions Measurement Field Strength of Spurious Radiation Measurement Frequency Stability Measurement LIST OF MEASURING EQUIPMENT UNCERTAINTY OF EVALUATION APPENDIX A. SETUP PHOTOGRAPHS SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 2 of 30

3 REVISION HISTORY REPORT NO. VERSION DESCRIPTION ISSUED DATE FW533001A Rev. 01 Initial issue of report May 11, 2015 SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 3 of 30

4 SUMMARY OF TEST RESULT Report Section FCC Rule Description Limit Result Remark Conducted Output Power Reporting only PASS % Occupied Bandwidth and 26dB Bandwidth Reporting only PASS Emission masks In-band emissions < 50+10log 10 (P[Watts]) PASS Emission masks Out of band emissions < 43+10log 10 (P[Watts]) PASS Field Strength of Spurious Radiation < 43+10log 10 (P[Watts]) PASS Under limit db at MHz Frequency Stability for Temperature & Voltage < 2.5 ppm PASS - SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 4 of 30

5 1 General Description 1.1 Applicant ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, , P. R. China 1.2 Manufacturer ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, , P. R. China 1.3 Feature of Equipment Under Test Product Feature & Specification Equipment CDMA/LTE Multi-Mode Digital Mobile Phone Brand Name ZTE Model Name N9518 FCC ID SRQ-ZTEN9518 EUT supports Radios application CDMA/EV-DO/LTE/WLAN 2.4GHz b/g/n HT20/ Bluetooth v3.0+edr/bluetooth v4.0 LE MEID Code Conducted: Radiated: HW Version cwxa SW Version N9518V1.0.0B01 EUT Stage Identical Prototype 1.4 Product Specification of Equipment Under Test Product Specification subjective to this standard Tx Frequency CDMA2000 BC10 : MHz ~ MHz Rx Frequency CDMA2000 BC10 : MHz ~ MHz Maximum Output Power to Antenna CDMA2000 BC10 : dbm Antenna Type Fixed Internal Antenna Type of Modulation CDMA2000 1xRTT : QPSK CDMA2000 1xEV-DO : 8PSK Remark: This test report recorded only product characteristics and test results of PCS Licensed Transmitter Held to Ear (PCE). SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 5 of 30

6 1.5 Modification of EUT No modifications are made to the EUT during all test items. 1.6 Maximum Frequency Tolerance and Emission Designator FCC Rule System Type of Modulation Frequency Tolerance (ppm) Emission Designator Part 90S CDMA2000 BC10 1xRTT QPSK ppm 1M28F9W 1.7 Testing Site Test Site SPORTON INTERNATIONAL (KUNSHAN) INC. No. 3-2, PingXiang Road, Kunshan, Jiangsu Province, P. R. China Test Site Location TEL: FAX: Test Site No. Sporton Site No. FCC Registration No. TH01-KS 03CH02-KS Note: The test site complies with ANSI C requirement. 1.8 Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: Preliminary Guidance for Receiving Applications for Certification of 3G Device. May 9, FCC 47 CFR Part 2, 90 ANSI / TIA / EIA-603-C-2004 Remark: 1. All test items were verified and recorded according to the standards and without any deviation during the test. 2. This EUT has also been tested and complied with the requirements of FCC Part 15, Subpart B, recorded in a separate test report. SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 6 of 30

7 2 Test Configuration of Equipment Under Test 2.1 Test Mode During all testing, EUT is in link mode with base station emulator at maximum power level. The spurious emission measurements were carried out in semi-anechoic chamber with 3-meter test range, and EUT is rotated on three test planes to find out the worst emission (X Plane). Frequency range investigated for radiated emission: 30MHz to 10 th harmonic. Test Modes Band Radiated TCs Conducted TCs CDMA2000 BC10 1xRTT Link 1xRTT Link Note: The maximum RF output power levels are 1xRTT RC1+SO55 mode for CDMA2000 BC10 on QPSK Link; only these modes were used for all tests. The conducted power table is as follows: Conducted Power (*Unit: dbm) Band CDMA2000 BC10 Channel Frequency xRTT RC1+SO xRTT RC3+SO xRTT RC3 SO32(+ F-SCH) xRTT RC3 SO32 (+SCH) xEVDO RTAP 153.6Kbps xEVDO RETAP 4096Bits SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 7 of 30

8 2.2 Connection Diagram of Test System 2.3 Support Unit used in test configuration and system Item Equipment Trade Name Model No. FCC ID Data Cable Power Cord 1. System Simulator R&S CMU 200 N/A N/A Unshielded, 1.8 m 2. DC Power Supply GW INSTEK GPD-2303S N/A N/A Unshielded, 1.8 m 3. Earphone Lenovo SH100 N/A Unshielded, 1.2 m N/A SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 8 of 30

9 2.4 Measurement Results Explanation Example For all conducted test items: The offset level is set in the spectrum analyzer to compensate the RF cable loss and attenuator factor between EUT conducted output port and spectrum analyzer. With the offset compensation, the spectrum analyzer reading level is exactly the EUT RF output level. Example: The spectrum analyzer offset is derived from RF cable loss and attenuator factor. Offset = RF cable loss + attenuator factor. Following shows an offset computation example with cable loss 5.2 db and 10dB attenuator. Offset (db) = RF cable loss (db) + attenuator factor (db). = = 15.2 (db) SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 9 of 30

10 3 Test Result 3.1 Conducted Output Power Measurement Description of the Conducted Output Power Measurement A base station simulator was used to establish communication with the EUT. Its parameters were set to transmit the maximum power on the EUT. The measured power in the radio frequency on the transmitter output terminals shall be reported Measuring Instruments The measuring equipment is listed in the section 4 of this test report Test Procedures 1. The transmitter output port was connected to base station. 2. Set EUT at maximum power through base station. 3. Select lowest, middle, and highest channels for each band and different modulation Test Setup SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 10 of 30

11 3.1.5 Test Result of Conducted Output Power CDMA 2000 BC10 Modes CDMA xRTT Test Status RC1+SO55 Channel 467 (Low) 580 (Mid) 684 (High) Frequency (MHz) Conducted Power (dbm) Note: Maximum burst average power for CDMA. SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 11 of 30

12 3.2 99% Occupied Bandwidth and 26dB Bandwidth Measurement Description of (Occupied) Bandwidth Limitations Measurement The 99% occupied bandwidth is the width of a frequency band such that, below the lower and above the upper frequency limits, the mean powers emitted are each equal to a specified percentage 0.5% of the total mean transmitted power. The emission bandwidth is defined as the width of the signal between two points, located at the 2 sides of the carrier frequency, outside of which all emissions are attenuated at least 26 db below the transmitter power Measuring Instruments The measuring equipment is listed in the section 4 of this test report Test Procedures 1. The EUT was connected to Spectrum Analyzer and Base Station via power divider. 2. The 99% and 26 db occupied bandwidth (BW) of the middle channel for the highest RF powers were measured Test Setup SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 12 of 30

13 3.2.5 Test Result of 99% Occupied Bandwidth and 26dB Bandwidth CDMA2000 BC10 Test Mode Test Status CDMA xRTT RC1+SO55 Channel 476 (Low) 580 (Mid) 684 (High) Frequency (MHz) % OBW (MHz) dB BW (MHz) SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 13 of 30

14 3.2.6 Test Result (Plots) of 99% Occupied Bandwidth and 26dB Bandwidth Band : CDMA2000 BC 10 Test Mode : 1xRTT_RC1+SO55 99% Occupied Bandwidth Plot on Channel 476 (817.9MHz) Ref 30 dbm * RBW 30 khz * VBW 100 khz * Att 30 db * SWT 300 ms Marker 1 [T1 ] dbm MHz 1 PK MAXH Offset 15.2 db T1 1 OBW MHz Temp 1 [T1 OBW] 7.87 dbm A MHz Temp 2 [T1 OBW] T dbm LVL MHz DB Center MHz 250 khz/ Span 2.5 MHz Date: 2.APR :07:53 26dB Bandwidth Plot on Channel 476 (817.9MHz) Ref 30 dbm * RBW 30 khz * VBW 100 khz * Att 30 db * SWT 300 ms Marker 1 [T1 ] dbm MHz 30 Offset 15.2 db ndb [T1] db 1 PK MAXH BW MHz Temp 1 [T1 ndb] A dbm MHz Temp 2 [T1 ndb] LVL dbm MHz T1 T DB Center MHz 250 khz/ Span 2.5 MHz Date: 2.APR :00:43 SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 14 of 30

15 99% Occupied Bandwidth Plot on Channel 580 (820.5MHz) Ref 30 dbm * RBW 30 khz * VBW 100 khz * Att 30 db * SWT 300 ms Marker 1 [T1 ] dbm MHz 1 PK MAXH Offset 15.2 db T1 1 OBW MHz Temp 1 [T1 OBW] 7.60 dbm A MHz Temp 2 [T1 OBW] T dbm LVL MHz DB Center MHz 250 khz/ Span 2.5 MHz Date: 2.APR :06:56 26dB Bandwidth Plot on Channel 580 (820.5MHz) Ref 30 dbm * RBW 30 khz * VBW 100 khz * Att 30 db * SWT 300 ms Marker 1 [T1 ] dbm MHz 30 Offset 15.2 db ndb [T1] db 1 PK MAXH BW MHz A 1Temp 1 [T1 ndb] dbm MHz Temp 2 [T1 ndb] LVL dbm MHz T1 T DB Center MHz 250 khz/ Span 2.5 MHz Date: 2.APR :01:24 SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 15 of 30

16 99% Occupied Bandwidth Plot on Channel 684 (823.1MHz) Ref 30 dbm * RBW 30 khz * VBW 100 khz * Att 30 db * SWT 300 ms Marker 1 [T1 ] dbm MHz 1 PK MAXH Offset 15.2 db T1 1 OBW MHz Temp 1 [T1 OBW] dbm A MHz Temp 2 [T1 OBW] T dbm LVL MHz DB Center MHz 250 khz/ Span 2.5 MHz Date: 2.APR :03:27 26dB Bandwidth Plot on Channel 684 (823.1MHz) Ref 30 dbm * RBW 30 khz * VBW 100 khz * Att 30 db * SWT 300 ms Marker 1 [T1 ] dbm MHz 30 Offset 15.2 db ndb [T1] db 1 PK MAXH BW MHz Temp 1 [T1 ndb] A dbm MHz Temp 2 [T1 ndb] LVL dbm MHz T1 T DB Center MHz 250 khz/ Span 2.5 MHz Date: 2.APR :02:08 SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 16 of 30

17 3.3 Emissions Mask Measurement Description of Emissions Mask Measurement Equipment used in this licensed to EA or non-ea systems shall comply with the emission mask provisions of FCC Part (a)(1) Measuring Instruments The measuring equipment is listed in the section 4 of this test report Test Procedures 1. The EUT was connected to spectrum analyzer and base station via power divider. 2. The emissions mask of low and high channels for the highest RF powers were measured. 3. The RBW was set 1% of 99% Occupied Bandwidth, and VBW was set 3 times of RBW. 4. The final test results were shown below plots with a correction offset factor including cable loss, insertion loss of power divider Test Setup SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 17 of 30

18 3.3.5 Test Result (Plots) of Conducted Emissions Mask Band : CDMA2000 BC10 Test Mode : 1xRTT_RC1+SO55 Lower Band Edge Plot on Channel 476 (817.9MHz) Ref 30 dbm RM * AVG -10 Offset 15.2 db -20 SWP 100 of LIMIT CHECK PASS A SGL LVL -40 SPECT DB Start MHz 300 khz/ Stop MHz Tx Channel Bandwidth 1.5 MHz Power dbm Start Stop RBW Freq PwrAbs PwrRel Limit [Hz] [Hz] [Hz] [Hz] [dbm] [dbc] [db] M k k M k k k M k k k M k M k M Date: 3.APR :25:11 Higher Band Edge Plot on Channel 684 (823.1MHz) Ref 30 dbm Offset 15.2 db RM * AVG SWP 100 of LIMIT CHECK PASS A SGL LVL -40 SPECT DB Start MHz 300 khz/ Stop MHz Tx Channel Bandwidth 1.5 MHz Power dbm Start Stop RBW Freq PwrAbs PwrRel Limit [Hz] [Hz] [Hz] [Hz] [dbm] [dbc] [db] M k k M k k k M k k k M k M k M Date: 3.APR :17:19 SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 18 of 30

19 3.4 Emissions Mask Out Of Band Emissions Measurement Description of Conducted Emissions Out of band emissions measurement The power of any emission FCC Part (a)(2) on any frequency removed from the assigned frequency by more than 250 percent of the authorized bandwidth at least log (P) db. It is measured by means of a calibrated spectrum analyzer and scanned from 30 MHz up to a frequency including its 10 th harmonic Measuring Instruments The measuring equipment is listed in the section 4 of this test report Test Procedures 1. The EUT was connected to spectrum analyzer and base station via power divider. 2. The middle channel for the highest RF power within the transmitting frequency was measured. 3. The conducted spurious emission for the whole frequency range was taken. 4. The final test results were shown below plots with a correction offset factor including cable loss, insertion loss of power divider Test Setup SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 19 of 30

20 3.4.5 Test Result (Plots) of Conducted Emission Band : CDMA2000 BC10 Test Mode : 1xRTT_RC1+SO55 Conducted Emission Plot between on Channel 476 (817.9MHz) Ref 0 dbm Offset 15.2 db -10 _SPULIN_ -20 LIMIT CHECK PASS A 1 MAXH LVL SPUEM DB Start 30 MHz GHz/ Stop GHz Start Stop RBW Freq PwrAbs Limit [Hz] [Hz] [Hz] [Hz] [dbm] [db] M M k M M G k M G G k G G G k G G G k G G G k G Date: 3.APR :50:20 SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 20 of 30

21 Conducted Emission Plot between on Channel 580 (820.5MHz) Ref 0 dbm Offset 15.2 db -10 _SPULIN_ -20 LIMIT CHECK PASS A 1 MAXH LVL SPUEM DB Start 30 MHz GHz/ Stop GHz Start Stop RBW Freq PwrAbs Limit [Hz] [Hz] [Hz] [Hz] [dbm] [db] M M k M M G k M G G k G G G k G G G k G G G k G Date: 3.APR :19:29 SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 21 of 30

22 Conducted Emission Plot between on Channel 684 (823.1MHz) Ref 0 dbm Offset 15.2 db -10 _SPULIN_ -20 LIMIT CHECK PASS A 1 MAXH LVL SPUEM DB Start 30 MHz GHz/ Stop GHz Start Stop RBW Freq PwrAbs Limit [Hz] [Hz] [Hz] [Hz] [dbm] [db] M M k M M G k M G G k G G G k G G G k G G G k G Date: 3.APR :20:20 SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 22 of 30

23 3.5 Field Strength of Spurious Radiation Measurement Description of Field Strength of Spurious Radiated Measurement The radiated spurious emission was measured by substitution method according to ANSI / TIA / EIA-603-C The power of any emission FCC Part on any frequency removed from the assigned frequency by more than 250 percent of the authorized bandwidth at least log (P) db. The spectrum is scanned from 30 MHz up to a frequency including its 10th harmonic. The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitter power (P) by a factor of at least 43+10log 10 (P[Watts]) db. The spectrum is scanned from 30 MHz up to a frequency including its 10th harmonic Measuring Instruments The measuring equipment is listed in the section 4 of this test report Test Procedures 1. The EUT was placed on a rotatable wooden table with 0.8 meter about ground. 2. The EUT was set 3 meters from the receiving antenna, which was mounted on the antenna tower. 3. The table was rotated 360 degrees to determine the position of the highest spurious emission. 4. The height of the receiving antenna is varied between one meter and four meters to search the maximum spurious emission for both horizontal and vertical polarizations. 5. Make the measurement with the spectrum analyzer's RBW = 1MHz, VBW = 3MHz, Sweep = 500ms, Taking the record of maximum spurious emission. 6. A horn antenna was substituted in place of the EUT and was driven by a signal generator. 7. Tune the output power of signal generator to the same emission level with EUT maximum spurious emission. 8. Taking the record of output power at antenna port. 9. Repeat step 7 to step 8 for another polarization. 10. EIRP (dbm) = S.G. Power Tx Cable Loss + Tx Antenna Gain 11. ERP (dbm) = EIRP The RF fundamental frequency should be excluded against the limit line in the operating frequency band. 13. The limit line is derived from log(P) db below the transmitter power P(Watts) = P(W) - [ log(P)] (db) = [ log(P)] (dbm) - [ log(P)] (db) = -13dBm. SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 23 of 30

24 3.5.4 Test Setup SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 24 of 30

25 3.5.5 Test Result of Field Strength of Spurious Radiated Band : CDMA2000 BC10 Temperature : 21~22 C Test Mode : 1xRTT_RC1+SO55 Relative Humidity : 41~42% Test Engineer : Jack Wang Polarization : Horizontal Remark : Spurious emissions within MHz were found more than 20dB below limit line. Frequency ERP Limit Over SPA S.G. TX Cable TX Antenna Polarization Result Limit Reading Power loss Gain ( MHz ) ( dbm ) ( dbm ) ( db ) (dbm) ( dbm ) ( db ) (dbi) (H/V) H Pass H Pass H Pass Band : CDMA2000 BC10 Temperature : 21~22 C Test Mode : 1xRTT_RC1+SO55 Relative Humidity : 41~42% Test Engineer : Jack Wang Polarization : Vertical Remark : Spurious emissions within MHz were found more than 20dB below limit line. Frequency ERP Limit Over SPA S.G. TX Cable TX Antenna Polarization Result Limit Reading Power loss Gain ( MHz ) ( dbm ) ( dbm ) ( db ) (dbm) ( dbm ) ( db ) (dbi) (H/V) V Pass V Pass V Pass SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 25 of 30

26 3.6 Frequency Stability Measurement Description of Frequency Stability Measurement The frequency stability shall be measured by variation of ambient temperature and variation of primary supply voltage to ensure that the fundamental emission stays within the authorized frequency block. The frequency stability of the transmitter shall be maintained within ± % (±2.5ppm) of the center frequency according to FCC Part Measuring Instruments The measuring equipment is listed in the section 4 of this test report Test Procedures for Temperature Variation 1. The EUT was set up in the thermal chamber and connected with the base station. 2. With power OFF, the temperature was decreased to -30 C and the EUT was stabilized for three hours. Power was applied and the maximum change in frequency was recorded within one minute. 3. With power OFF, the temperature was raised in 10 C step up to 50 C. The EUT was stabilized at each step for at least half an hour. Power was applied and the maximum frequency change was recorded within one minute Test Procedures for Voltage Variation 1. The EUT was placed in a temperature chamber at 25±5 C and connected with the base station. 2. The power supply voltage to the EUT was varied from BEP to 115% of the nominal value measured at the input to the EUT. 3. The variation in frequency was measured for the worst case. SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 26 of 30

27 3.6.5 Test Setup Test Result of Temperature Variation Band : CDMA2000 BC10 Channel : 580 Test Mode : 1xRTT_RC1+SO55 Limit (ppm) : 2.5 Temperature ( C) Deviation (ppm) (Ref.) Result PASS SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 27 of 30

28 3.6.7 Test Result of Voltage Variation Band & Channel Mode Voltage (Volt) Deviation (ppm) Limit (ppm) Result CDMA2000 BC10 CH580 1xRTT_RC1+SO PASS BEP Note: 1. Normal Voltage = 3.8V. 2. Battery End Point (BEP) = 3.6 V. 3. The manufacturer declared that the EUT could work properly between voltage 3.6V ~ 4.35V. SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 28 of 30

29 4 List of Measuring Equipment Instrument Manufacturer Model No. Serial No. Characteristics Calibration Date Test Date Due Date Remark Spectrum Analyzer Thermal Chamber EMI Test Receiver R&S FSP kHz~40GHz Oct. 28, 2014 Ten Billion TTC-B3S TBN ~+150 C Oct. 25, 2014 R&S ESR kHz~7GHz;Max 30dBm Apr. 02, 2015~ Apr. 03, 2015 Apr. 02, 2015~ Apr. 03, 2015 Oct. 27, 2015 Oct. 24, 2015 Sep. 29, 2014 Apr. 20, 2015 Sep. 28, 2015 Conducted (TH01-KS) Conducted (TH01-KS) Radiation (03CH02-KS) Spectrum Analyzer R&S FSV kHz~40GHz;Ma x 30dBm Sep. 25, 2014 Apr. 20, 2015 Sep. 24, 2015 Radiation (03CH02-KS) Bilog Antenna TeseQ CBL6112D MHz-2GHz Sep. 13, 2014 Apr. 20, 2015 Sep. 12, 2015 Radiation (03CH02-KS) Double Ridge Horn Antenna Active Horn Antenna ETS-Lindgren GHz~18GHz Nov. 08, 2014 Apr. 20, 2015 Nov. 07, 2015 com-power AHA GHz~18GHz Nov. 08, 2014 Apr. 20, 2015 Nov. 07, 2015 Radiation (03CH02-KS) Radiation (03CH02-KS) SHF-EHF Horn com-power AH GHz~40GHz Sep. 04, 2014 Apr. 20, 2015 Sep. 03, 2015 Radiation (03CH02-KS) Amplifier com-power PA-103A kHz ~1000MHz / 32 db May 04, 2014 Apr. 20, 2015 May 03, 2015 Radiation (03CH02-KS) Amplifier Agilent 8449B 3008A GHz Gain 30dB Oct. 28, 2014 Apr. 20, 2015 Oct. 27, 2015 Radiation (03CH02-KS) AC Power Source Chroma N/A NCR Apr. 20, 2015 NCR Radiation (03CH02-KS) Turn Table MF MF7802 N/A 0~360 degree NCR Apr. 20, 2015 NCR Antenna Mast MF MF7802 N/A 1 m~4 m NCR Apr. 20, 2015 NCR Radiation (03CH02-KS) Radiation (03CH02-KS) SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 29 of 30

30 5 Uncertainty of Evaluation Uncertainty of Radiated Emission Measurement (30 MHz ~ 1000 MHz) Measuring Uncertainty for a Level of Confidence of 95% (U = 2Uc(y)) 5.1 db SPORTON INTERNATIONAL (KUNSHAN) INC. Page Number : 30 of 30