FT-991. reference BOOk YAESU MUSEN CO., LTD.

Size: px
Start display at page:

Download "FT-991. reference BOOk YAESU MUSEN CO., LTD."

Transcription

1 FT- CAT OperATiOn reference BOOk YAESU MUSEN CO., LTD.

2 Overview The CAT (Computer Aided Transceiver) System in the FT- transceiver provides control of frequency, VFO, memory, and other settings such as dualchannel memories and diversity reception using an external personal computer. This allows multiple control operations to be fully automated with single mouse clicks, or keystroke operations on the computer keyboard. Using the RS-C Cable (Refer to igure ) The FT- transceiver has a built-in level converter, allowing direct connection from the rear-panel CAT jack to the serial port of your computer without the need of any external boxes. When using the RS-C cable, set Menu item 0 GPS/C SELECT to RSC. You will need a serial cable for connection to the RS- C (serial or COM port) connector on your computer. Purchase a standard serial cable (not the so-called null modem type), ensuring it has the correct gender and number of pins (some serial COM port connectors use a -pin rather than -pin coniguration). If your computer uses a custom connector, you may have to construct the cable. In this case, refer to the technical documentation supplied with your computer for correct data connection. COnneCTiOn 7 6 Pin No. Pin Name I/O Function N/A SERIAL OUT Output SERIAL IN Input Outputs the Serial Data from the transceiver to the computer. Inputs the Serial Data from the computer to the transceiver. N/A GND --- Signal Ground N/A RTS CTS N/A Personal Computer Using the USB Cable (Refer to igure ) Note: A USB driver is required for remote control from a computer. Download the driver from the Yaesu website ( The FT- transceiver has a built-in USB to Dual UART Bridge, allowing direct connection from the rear-panel USB jack to the USB jack of your computer without the need of any external boxes. COM FT- GPS/CAT You will need a USB cable to connect to the USB jack on your computer. YAESU MUSEN does not produce CAT System operating software due to the wide variety of personal computers and operating systems in use today. However, the information provided in this chapter explains the serial data structure and opcodes used by the CAT system. This information, along with the short programming examples, is intended to help you start writing programs on your own. As you become more familiar with CAT operation, you can customize programs for your operating needs and utilize the full operating potential of this system. Personal Computer Figure RS-C Straight Cable FT- USB USB Figure USB Cable

3 COnTrOl COmmAnd A computer control command is composed of an alphabetical command, various parameters, and the terminator that signals the end of the control command. Example: the VFO-A frequency to.0000 MHz. FA Command Parameter Terminator There are three commands for the FT- as shown below: command: a particular condition (to the FT-) command: s an answer (from the FT-) command: Transmits a condition (from the FT-) For example, note the following case of the FA command ( the VFO-A frequency): To set the VFO-A frequency to.0000 MHz, the following command is sent from the computer to the transceiver: FA00000 ( command) To read the VFO-A frequency, the following command is sent from the computer to the transceiver: FA ( command) When the command above has been sent, the following command is returned to the computer: FA00000 ( command) Alphabetical Commands A command consists of alphabetical characters. You may use either lower or upper case characters. The commands available for this transceiver are listed in the PC Control Command Tables on the following pages. Parameters Parameters are used to specify information necessary to implement the desired command. The parameters to be used for each command are predetermined. The number of digits assigned to each parameter is also predetermined. Refer to the Control Command List and the Control Command Tables to conigure the appropriate parameters. When configuring parameters, be careful not to make the following mistakes. For example, when the correct parameter is IS0+000 (IF SHIFT): IS0000 Not enough parameters speciied (No direction (+) given for the IF shift) IS0+00 Not enough digits (Only three frequency digits given) IS0_+_000 Unnecessary characters between parameters IS Too many digits (Five frequency digits given) Note: If a particular parameter is not applicable to the FT-, the parameter digits should be illed using any character except the ASCII control codes (00 to Fh) and the terminator (). Terminator To signal the end of a command, it is necessary to use a semicolon (). The digit where this special character must appear differs depending on the command used.

4 Command Function Ans. AI AB VFO-A TO VFO-B O X X X AC ANTENNA TUNER CONTROL O O O O AG AF GAIN O O O O AI AUTO INFORMATION O O O X AM VFO-A TO MEMORY CHANNEL O X X X BA VFO-B TO VFO-A O X X X BC AUTO NOTCH O O O O BD BAND DOWN O X X X BI BREAK-IN O O O O BP MANUAL NOTCH O O O O BS BAND SELECT O X X X BU BAND UP O X X X BY BUSY X O O O CH CHANNEL UP/DOWN O X X X CN CTCSS NUMBER O O O O CO CONTOUR O O O O CS CW SPOT O O O O CT CTCSS O O O O DA DIMMER O O O X DN DOWN O X X X DT DATE AND TIME O O O X ED ENCORDER DOWN O X X X EK ENT KEY O X X X EU ENCORDER UP O X X X EX MENU O O O O FA FREQUENCY VFO-A O O O O FB FREQUENCY VFO-B O O O O FS FAST STEP O O O O FT FUNCTION TX O O O O GT AGC FUNCTION O O O O ID IDENTIFICATION X O O X IF INFORMATION X O O O IS IF-SHIFT O O O O KM KEYER MEMORY O O O X KP KEY PITCH O O O O KR KEYER O O O O KS KEY SPEED O O O O KY CW KEYING O X X X LK LOCK O O O O LM LOAD MESSEGE O O O X MA MEMORY CHANNEL TO VFO-A O X X X MC MEMORY CHANNEL O O O X MD MODE O O O O MG MIC GAIN O O O O ML MONITOR LEVEL O O O O MR MEMORY READ X O O X MS METER SW O O O O MW MEMORY WRITE O X X X MX MOX SET O O O O NA NARROW O O O O NB NOISE BLANKER O O O O NL NOISE BLANKER LEVEL O O O O NR NOISE REDUCTION O O O O OI OPPOSITE BAND NFORMATION X O O O OS OFFSET (Repeater Shift) O O O O PA PRE-AMP (IPO) O O O O PB PLAY BACK O O O X PC POWER CONTROL O O O O PL SPEECH PROCESSOR LEVEL O O O O Command Function Ans. AI PR SPEECH PROCESSOR O O O O PS POWER SWITCH O O O X QI QMB STORE O X X X QR QMB RECALL O X X X QS QUICK SPLIT O X X X RA RF ATTENUATOR O O O O RC CLAR CLEAR O X X X RD CLAR DOWN O X X X RG RF GAIN O O O O RI RADIO INFORMATION X O O O RL NOISE REDUCTION LEVEL O O O O RM READ METER X O O O RS RADIO STATUS X O O X RT CLAR O O O O RU CLAR UP O X X X SC SCAN O O O O SD SEMI BREAK-IN DELAY TIME O O O O SH WIDTH O O O O SM S METER X O O X SQ SQUELCH LEVEL O O O O SV SWAP VFO O X X X TS TXW O O O O TX TX SET O O O O UL UNLOCK X O O O UP UP O X X X VD VOX DELAY TIME O O O O VG VOX GAIN O O O O VM [V/M] KEY FUNCTION O X X X VX VOX O O O O XT TX CLAR O O O O ZI ZERO IN O X X X

5 AB VFO-A TO VFO-B A B AC ANTENNA TUNER CONTROL 0: Fixed P 0: Tuner OFF A C P P P 0: Fixed : Tuner ON : Tuning Start A C A C P P AG AF GAIN 0: Fixed A G P P P P A G A G P P P AI AUTO INFORMATION 0: Auto Information OFF A I : Auto Information ON A I A I This parameter is set to 0 (OFF) automatically when the transceiver is turned OFF. AM VFO-A TO MEMORY CHANNEL A M BA VFO-B TO VFO-A B A BC AUTO NOTCH 0: Fixed B C P P 0: Auto Notch OFF : Auto Notch ON B C B C P BD BAND DOWN 0: Fixed B D

6 BI BREAK-IN 0: Break-in OFF B I : Break-in ON B I B I BP MANUAL NOTCH 0: Fixed P P=0 B P P P P P P 0: Manual NOTCH ON/OFF 000: OFF B P P : Manual NOTCH LEVEL 00: ON P= 00-0 (NOTCH Frequency : x 0 Hz ) B P P P P P BS BAND SELECT 00:. MHz 06: MHz : MW B S 0:. MHz 07: MHz : - 0: - 0:. MHz : AIR 0: 7 MHz 0: MHz : MHz 0: 0 MHz 0: 0 MHz 6: 0 MHz 0: MHz : GEN BU BAND UP 0: Fixed B U BY BUSY 0: RX BUSY OFF : RX BUSY ON P 0: Fixed B Y B Y P CH CHANNEL UP/DOWN 0: Memory Channel UP C H : Memory Channel DOWN CN CTCSS TONE FREQUENCY 0: Fixed C N P P P 0 - : Tone Frequency Number (See Table ) C N C N P P CO CONTOUR 0: Fixed P P=0 0000: CONTOUR OFF C O P P P P P P 0: CONTOUR ON/OFF 000: CONTOUR ON : CONTOUR FREQ P= : APF ON/OFF (CONTOUR Frequency:0-00Hz) C O P : APF FREQ P= 0000: APF OFF 000: APF ON P= (APF Frequency: -0-0 Hz ) C O P P P P P

7 CS CW SPOT 0: OFF C S : ON C S C S CT CTCSS 0: Fixed C C T T P P 0: CTCSS OFF : CTCSS ENC/DEC ON : CTCSS ENC ON : DCS ON C T P Table (CTCSS Tone Chart) Hz 0. Hz.0 Hz 7 6. Hz 6. Hz. Hz 0 6. Hz 0. Hz 7. Hz 6. Hz 7. Hz 6.6 Hz 0 7. Hz 7. Hz 0. Hz 67. Hz 6.6 Hz 7. Hz 0 7. Hz 00.0 Hz 6. Hz 0 7. Hz. Hz 0. Hz Hz 0. Hz. Hz 7. Hz 0 0. Hz. Hz Hz 07. Hz 6. Hz 77. Hz 06. Hz Hz 0. Hz. Hz 7. Hz 0.7 Hz Hz 6. Hz 6.7 Hz. Hz. Hz Hz 7. Hz 6. Hz 6. Hz.7 Hz - - DA DIMMER 00: Fixed D A P P P P P 0-0: LED Indicators Brightness Level P 00 - : TFT Display Brightness Level D A D A P P P P DN MIC DWN D N DT DATE AND TIME 6 7 ~ n- n 0: Date D T P P P 6 P 7 ~ P 0 : Time (UTC) : Time differential (Time Zone) P =0 yyyymmdd (Year/Month/Date) D T = hhmmss (Hour/Minute/Second, hour time system) 6 7 ~ n- n = hhmm (Hour/Minute, 0 minute increments) D T P P P P ~ P ED ENCORDER DOWN 0: MAIN ENCORDER E D P P : SUB ENCORDER : MULTI ENCORDER P 0 - : Steps EK ENT KEY E K 6

8 EU ENCORDER UP 0: MAIN ENCORDER E U P P : SUB ENCORDER : MULTI ENCORDER P 0 - : Steps EX MENU 6 7 ~ n- n : 00 - (MENU Number) E X P P ~ P P : Parameter (See Table) E X 6 7 ~ n- n E X P P ~ P Function P Digits 00 AGC FAST DELAY 0 ~ 000 msec (P= 000 ~ 000, 0 msec/step) 00 AGC MID DELAY 0 ~ 000 msec (P= 000 ~ 000, 0 msec/step) 00 AGC SLOW DELAY 0 ~ 000 msec (P= 000 ~ 000, 0 msec/step) 00 HOME FUNCTION 0: SCOPE : FUNCTION 00 MY CALL INDICATION 0 ~ sec 006 DISPLAY COLOR 0: BLUE : GRAY : GREEN : ORANGE : PURPLE : RED 6: SKY BLUE 007 DIMMER LED 0: : 00 DIMMER TFT 00 ~ 00 BAR MTR PEAK HOLD 0: OFF : 0. sec :.0 sec :.0 sec 00 DVS RX OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 0 DVS TX OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 0 KEYER TYPE 0: OFF : BUG : ELEKEY-A : ELEKEY-B : ELEKEY-Y : ACS 0 KEYER DOT/DASH 0: NORNAL : REVERSE 0 CW WEIGHT. ~. (P = ~ ) 0 BEACON INTERVAL OFF / ~ 60 sec (P = 000 ~ 60, 000: OFF) 06 NUMBER STYLE 0: 0 : AUNO : AUNT : ANO : ANT : NO 6: NT 07 CONTEST NUMBER 0000 ~ 0 CW MEMORY 0: TEXT : MESSAGE 0 CW MEMORY 0: TEXT : MESSAGE 00 CW MEMORY 0: TEXT : MESSAGE 0 CW MEMORY 0: TEXT : MESSAGE 0 CW MEMORY 0: TEXT : MESSAGE 0 NB WIDTH 0: ms : ms : 0 ms 0 NB REJECTION 0: 0 db : 0 db : 0 db 0 NB LEVEL 0 ~ 0 (P = 00 ~ 0) 06 BEEP LEVEL 0 ~ 00 (P = 000 ~ 00) 07 TIME ZONE UTC :00 ~ +:00 0 GPS/C SELECT 0: GPS : RSC 0 C RATE 0: 00 bps : 600 bps : 00 bps : 00 bps 00 C TOT 0: 0 msec : 00 msec : 000 msec : 000 msec 0 CAT RATE 0: 00 bps : 600 bps : 00 bps : 00 bps 0 CAT TOT 0: 0 msec : 00 msec : 000 msec : 000 msec 0 CAT RTS 0: DISABLE : ENABLE 0 MEM GROUP 0: DISABLE : ENABLE 0 QUICK SPLIT FREQ 0 khz ~ +00 (or 00) ~ +0 khz (P= 0 ~ +00 or 00 ~ +0) 06 TX TOT 0 (OFF) ~ 0 min (P= 00 ~ 0) 07 MIC SCAN 0: DISABLE : ENABLE 0 MIC SCAN RESUME 0: PAUSE : TIME 0 REF FREQ ADJ ~ +00 (or 00) ~ + (P= ~ +00 or 00 ~ +) 00 CLAR MODE SELECT 0: RX : TX : TRX 0 AM LCUT FREQ 00: OFF 0: 00 Hz ~ : 000 Hz (0 Hz steps) 0 AM LCUT SLOPE 0: 6 db/oct : db/oct 0 AM HCUT FREQ 00: OFF 0: 700 Hz ~ 67: 000 Hz (0 Hz steps) 0 AM HCUT SLOPE 0: 6 db/oct : db/oct 0 AM MIC SELECT 0: MIC : REAR 06 AM OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 07 AM PTT SELECT 0: DAKY : RTS : DTR 0 AM PORT SELECT 0: DATA : USB 0 AM DATA GAIN 0 ~ 00 (P = 000 ~ 00) 00 CW LCUT FREQ 00: OFF 0: 00 Hz ~ : 000 Hz (0 Hz steps) 0 CW LCUT SLOPE 0: 6 db/oct : db/oct 0 CW HCUT FREQ 00: OFF 0: 700 Hz ~ 67: 000 Hz (0 Hz steps) 0 CW HCUT SLOPE 0: 6 db/oct : db/oct 0 CW OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 0 CW AUTO MODE 0: OFF : 0 MHz : ON 06 CW BK-IN TYPE 0: SEMI BREAK-IN : FULL BREAK-IN 07 CW BK-IN DELAY 0 ~ 000 msec (P = 000 ~ 000, 0 msec/step) 0 CW WAVE SHAPE 0: msec : msec : msec : 6 msec 0 CW FREQ DISPLAY 0: DIRECT FREQ : PITCH OFFSET 060 PC KEYING 0: OFF : DAKY : RTS : DTR 06 QSK DELAY TIME 0: msec : 0 msec : mesc : 0 msec 7

9 Function P Digits 06 DATA MODE 0: PSK : OTHER 06 PSK TONE 0: 000 Hz : 00 Hz : 000 Hz 06 OTHER DISP (SSB) 000 Hz ~ 0 ~ +000 Hz (P = 000 ~ 0000 or ~ +000, 0 Hz steps) 06 OTHER SHIFT (SSB) 000 Hz ~ 0 ~ +000 Hz (P = 000 ~ 0000 or ~ +000, 0 Hz steps) 066 DATA LCUT FREQ 00: OFF 0: 00 Hz ~ : 000 Hz (0 Hz steps) 067 DATA LCUT SLOPE 0: 6 db/oct : db/oct 06 DATA HCUT FREQ 00: OFF 0: 700 Hz ~ 67: 000 Hz (0 Hz steps) 06 DATA HCUT SLOPE 0: 6 db/oct : db/oct 070 DATA IN SELECT 0: MIC : REAR 07 DATA PTT SELECT 0: DAKY : RTS : DTR 07 DATA PORT SELECT : DATA : USB 07 DATA OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 07 FM MIC SELECT 0: MIC : REAR 07 FM OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 076 FM PKT PTT SELECT 0: DAKY : RTS : DTR 077 FM PKT PORT SELECT : DATA : USB 07 FM PKT TX GAIN 0 ~ 00 (P = 000 ~ 00) 07 FM PKT MODE 0: 00 : RPT SHIFT MHz 0 ~ 000 khz (P = 0000 ~ 000, 0 khz/step) 0 RPT SHIFT 0MHz 0 ~ 000 khz (P = 0000 ~ 000, 0 khz/step) 0 RPT SHIFT MHz 0 ~ 000 khz (P = 0000 ~ 000, 0 khz/step) 0 RPT SHIFT 0MHz 0 ~ 0000 khz (P = 0000 ~ 0000, 0 khz/step) 0 ARS MHz 0: OFF : ON 0 ARS 0MHz 0: OFF : ON 06 DCS POLARITY 0: Tn-Rn : Tn-Riv : Tiv-Rn : Tiv-Riv 07 RADIO ID DIGITAL SQL TYPE 0: OFF : CODE : BREAK 0 DIGITAL SQL CODE 00 ~ 6 00 GM DISPLY 0: DISTANCE : STRENGTH 0 DISTANCE 0: km : mile 0 AMS TX MODE 0: AUTO : MANUAL : DN : VW : ANALOG 0 STANDBY BEEP 0: OFF : ON 0 RTTY LCUT FREQ 00: OFF 0: 00 Hz ~ : 000Hz (0 Hz steps) 0 RTTY LCUT SLOPE 0: 6 db/oct : db/oct 06 RTTY HCUT FREQ 00: OFF 0: 700 Hz ~ 67: 000Hz (0 Hz steps) 07 RTTY HCUT SLOPE 0: 6 db/oct : db/oct 0 RTTY SHIFT PORT 0: SHIFT : DTR : RTS 0 RTTY POLARITY-RX 0: NORNAL : REVERSE 00 RTTY POLARITY-TX 0: NORNAL : REVERSE 0 RTTY OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 0 RTTY SHIFT FREQ : 70 Hz : 00 Hz : Hz : 0 Hz 0 RTTY MARK FREQ : 7 Hz : Hz 0 SSB LCUT FREQ 00: OFF 0: 00 Hz ~ : 000 Hz (0 Hz steps) 0 SSB LCUT SLOPE 0: 6 db/oct : db/oct 06 SSB HCUT FREQ 00: OFF 0: 700 Hz ~ 67: 000 Hz (0 Hz steps) 07 SSB HCUT SLOPE 0: 6 db/oct : db/oct 0 SSB MIC SELECT 0: MIC : REAR 0 SSB OUT LEVEL 0 ~ 00 (P = 000 ~ 00) 0 SSB PTT SELECT 0: DAKY : RTS : DTR SSB PORT SELECT 0: DATA : USB SSB TX BPF 0: 0 ~ 000 : 00 ~ 00 : 00 ~ 00 : 00 ~ 700 : 00 ~ 600 APF WIDTH 0: NARROW : MEDIUM : WIDE CONTOUR LEVEL 0 ~ 0 ~ +0 (P = 0 ~ 00 or +00 ~ +0) CONTOUR WIDTH 0 ~ 6 IF NOTCH WIDTH 0: NARROW : WIDE 7 SCP DISPLAY MODE 0: SPECTRAM : WATER FALL SCP START CYCLE 0: OFF : sec : sec : 0 sec ASC DIAL SPEED 0: 0. khz/sec : 0. khz/sec : khz/sec : khz/sec : khz/sec : DISABLE 0 SCP SPAN FREQ 0: 0 khz 0: 00 khz 0: 00 khz 06: 00 khz 07: 000 khz PRMTRC EQ FREQ 00 : OFF 0: 00 0: 00 0: 00 0: 00 0: 00 06: : 700 Hz PRMTRC EQ LEVEL 0 ~ 0 ~ +0 (P = 0 ~ 00 or +00 ~ +0) PRMTRC EQ BWTH 0 ~ 0 PRMTRC EQ FREQ 00: OFF 0: 700 0: 00 0: 00 0: 000 0: 00 06: 00 07: 00 0: 00 0: 00 Hz PRMTRC EQ LEVEL 0 ~ 0 ~ +0 (P = 0 ~ 00 or +00 ~ +0) 6 PRMTRC EQ BWTH 0 ~ 0 7 PRMTRC EQ FREQ 00 : OFF 0: 00 0: 600 0: 700 0: 00 0: 00 06: 000 ~ : 00 Hz PRMTRC EQ LEVEL 0 ~ 0 ~ +0 (P = 0 ~ 00 or +00 ~ +0) PRMTRC EQ BWTH 0 ~ 0 0 P-PRMTRC EQ FREQ 00 : OFF 0: 00 0: 00 0: 00 0: 00 0: 00 06: : 700 Hz P-PRMTRC EQ LEVEL 0 ~ 0 ~ +0 (P = 0 ~ 00 or +00 ~ +0) P-PRMTRC EQ BWTH 0 ~ 0 P-PRMTRC EQ FREQ 00: OFF 0: 700 0: 00 0: 00 0: 000 0: 00 06: 00 07: 00 0: 00 0: 00 Hz P-PRMTRC EQ LEVEL 0 ~ 0 ~ +0 (P = 0 ~ 00 or +00 ~ +0) P-PRMTRC EQ BWTH 0 ~ 0 6 P-PRMTRC EQ FREQ 00 : OFF 0: 00 0: 600 0: 700 0: 00 0: 00 06: 000 ~ : 00 Hz 7 P-PRMTRC EQ LEVEL 0 ~ 0 ~ +0 (P = 0 ~ 00 or +00 ~ +0) P-PRMTRC EQ BWTH 0 ~ 0 HF TX MAX POWER ~ 00 (P = 00 ~ 00) 0 0M TX MAX POWER ~ 00 (P = 00 ~ 00) M TX MAX POWER ~ 0 (P = 00 ~ 00) 0M TX MAX POWER ~ 0 (P = 00 ~ 00) TUNER SELECT 0: OFF : INTERNAL : EXTERNAL : ATAS : LAMP

10 Function P Digits VOX SELECT 0: MIC : DATA VOX GAIN 000 ~ 00 6 VOX DELAY 0 ~ 000 msec (P = 000 ~ 000, 0 msec/step) 7 ANTI VOX GAIN 000 ~ 00 DATA VOX GAIN 000 ~ 00 DATA VOX DELAY 0 ~ 000 msec (P = 000 ~ 000) 0 ANTI DVOX GAIN 000 ~ 00 EMERGENCY FREQ TX 0: DISABLE : ENABLE FA FREQUENCY VFO-A (Hz) F A F A F A FB FREQUENCY VFO-B (Hz) F B F B F B FS FAST STEP 0: VFO-A FAST Key OFF F S : VFO-A FAST Key ON F S F S FT FUNCTION TX : VFO-A Band Transmitter: TX F F T T : VFO-B Band Transmitter: TX P 0: VFO-A Band Transmitter: TX : VFO-B Band Transmitter: TX F T P GT AGC FUNCTION 0: Fixed P 0: AGC OFF G T P P 0: AGC OFF : AGC FAST : AGC FAST : AGC MID : AGC MID : AGC SLOW G T : AGC SLOW : AGC AUTO-FAST : AGC AUTO : AGC AUTO-MID 6: AGC AUTO-SLOW G T P ID IDENTIFICATION 070: FT- I D I D

11 IF INFORMATION (Memory Channel) P VFO-A Frequency (Hz) P Clariier Direction +: Plus Shift, --: Minus Shift Clariier Offset: (Hz) P 0: RX CLAR OFF : RX CLAR ON I F P 0: TX CLAR OFF : TX CLAR ON P6 MODE : LSB : USB : CW : FM : AM 6: RTTY-LSB 7: CW-R : DATA-LSB : RTTY-USB A: DATA-FM B: FM-N C: DATA-USB I F P P P P P D: AM-N E: CFM P7 0: VFO : Memory : Memory Tune : Quick Memory Bank (QMB) : QMB-MT : PMS 6: HOME P P P P P P P P P P P 0: CTCSS OFF : CTCSS ENC/DEC : CTCSS ENC P 00: (Fixed) P P6 P7 P P P 0 0 0: Simplex : Plus Shift : Minus Shift IS IF-SHIFT 0:Fixed I S -/+ P P P P P -000 ~ +000 Hz (0 Hz steps) I S I S -/+ P P P P KM KEYER MEMORY 6 7 ~ n - : Keyer Memory Channel Number K M P P P P ~ P P Message Characters (up to 0 characters) K M 6 7 ~ n- n K M P P P P ~ P KP KEY PITCH 00: 00 Hz - 7: 00 Hz (0Hz steps) K P K P K P KR KEYER 0: KEYER OFF K R : KEYER ON K R K R KS KEY SPEED (WPM) K S K S K S KY CW KEYING : Keyer Memory Playback 6: Message Keyer Playback K Y : Keyer Memory Playback 7: Message Keyer Playback : Keyer Memory Playback : Message Keyer Playback : Keyer Memory Playback : Message Keyer Playback : Keyer Memory Playback A: Message Keyer Playback 0

12 LK LOCK 0: VFO-A DIAL Lock OFF L K : VFO-A DIAL Lock ON L K L K LM LOAD MESSEGE 0: DVS P 0: DVS (Recording Stop) L L M M P : DVS (CH Recording Start/Stop) : DVS (CH Recording Start/Stop) : DVS (CH Recording Start/Stop) : DVS (CH Recording Start/Stop) : DVS (CH Recording Start/Stop) L M P MA MEMORY CHANNEL TO VFO-A M A MC MEMORY CHANNEL 000-7: Memory Channel Number M C 000-0: Regular Memory Channel 00: P-L 0: P-U ~ 6: P-L 7: P-U M C M C MD OPERATING MODE 0: MAIN RX M D P P MODE : LSB : USB : CW-U : FM : AM 6: RTTY-LSB 7: CW-L : DATA-LSB : RTTY-USB A: DATA-FM B: FM-N C: DATA-USB D: AM-N E: CFM M D M D P MG MIC GAIN M G M G M G ML MONITOR LEVEL 0: MONI ON/OFF M L P P P : MONI Level P =0 000: MONI OFF M L 00: MONI ON = M L P P P

13 MR MEMORY CHANNEL READ P0/ (Memory Channel) P VFO-A Frequency (Hz) P Clariier Direction +: Plus Shift, --: Minus Shift Clariier Offset: (Hz) P 0: RX CLAR OFF : RX CLAR ON M R P0 P0 P0 P 0: TX CLAR OFF : TX CLAR ON P6 MODE : LSB : USB : CW : FM : AM 6: RTTY-LSB 7: CW-R M R P P P P P : DATA-LSB : RTTY-USB A: DATA-FM B: FM-N C: DATA-USB D: AM-N E: CFM P7 0: VFO : Memory P P P P P P P P P P P 0: CTCSS OFF : CTCSS ENC/DEC : CTCSS ENC P 00: (Fixed) P P6 P7 P P P 0 0 0: Simplex : Plus Shift : Minus Shift MS METER SW 0: COMP M M S S : ALC : PO : SWR : ID : VDD M S MW MEMORY CHANNEL WRITE (Memory Channel) P Frequency (Hz) M W P P P P P P Clariier Direction +: Plus Shift, --: Minus Shift Clariier Offset: (Hz) P 0: RX CLAR OFF : RX CLAR ON P P P P P P P P P P P 0: TX CLAR OFF : TX CLAR ON P6 MODE : LSB : USB : CW : FM : AM 6: RTTY-LSB 7: CW-R P P6 P7 P P P 0 : DATA-LSB : RTTY-USB A: DATA-FM B: FM-N C: DATA-USB D: AM-N E: CFM P7 00: (Fixed) P 0: CTCSS OFF : CTCSS ENC/DEC : CTCSS ENC P 00: (Fixed) 0 0: Simplex : Plus Shift : Minus Shift MX MOX SET 0: MOX OFF M X : MOX ON M X M X NA NARROW 0: Fixed M A P P 0: OFF : ON M A M A P NB NOISE BLANKER STATUS 0: Fixed N B P P 0: Noise Blanker OFF : Noise Blanker ON N B N B P NL NOISE BLANKER LEVEL 0: Fixed N L P P P P N L N L P P P

14 NR NOISE REDUCTION 0: Fixed N R P P 0: Noise Reduction OFF : Noise Reduction ON N R N R P OI OPPOSITE BAND INFORMATION (Memory Channel) P VFO-B Frequency (Hz) P Clariier Direction +: Plus Shift, --: Minus Shift Clariier Offset: (Hz) P 0: RX CLAR OFF : RX CLAR ON O I P 0: TX CLAR OFF : TX CLAR ON P6 MODE : LSB : USB : CW : FM : AM 6: RTTY-LSB 7: CW-R O I P P P P P : DATA-LSB : RTTY-USB A: DATA-FM B: FM-N C: DATA-USB D: AM-N E: CFM P7 0: VFO : Memory P P P P P P P P P P P 0: CTCSS OFF : CTCSS ENC/DEC : CTCSS ENC P 00: (Fixed) P P6 P7 P P P 0 0 0: Simplex : Plus Shift : Minus Shift OS OFFSET (REPEATER SHIFT) 0: Fixed O O S S P P 0: Simplex : Plus Shift : Minus Shift *: This command can be activated only with an FM mode. O S P PA PRE-AMP (IPO) 0:Fixed P P A A P P 0: IPO : AMP : AMP P A P PB PLAY BACK 0: DVS P 0: DVS (Playback Stop) P P B B P : DVS (CH Playback Start) : DVS (CH Playback Start) : DVS (CH Playback Start) : DVS (CH Playback Start) : DVS (CH Playback Start) P B P PC POWER CONTROL P C P C P C PL SPEECH PROCESSOR LEVEL P L P L P L

15 PR SPEECH PROCESSOR LEVEL 0: Speech Processor P P R R P : Parametric Microphone Equalizer P : OFF : ON P R P PS POWER SWITCH 0: POWER OFF P S : POWER ON P S P S This command requires dummy data be initially sent. Then after one second and before two seconds the command is sent. QI QMB STORE Q I QR QMB RECALL Q R QS QUICK SPLIT Q S RA RF ATTENUATOR 0: Fixed R A P P 0: OFF : ON R A R A P RC CLAR CLEAR R C RD CLAR DOWN (Hz) R D

16 RG RF GAIN 0: Fixed R G P P P P R G R G P P P RI RADIO INFORMATION 0: Hi-SWR A: TX LED P 0: OFF : REC : ON : PLAY : VFO-A TX R I 6: VFO-B TX 7: VFO-A RX R I P RL NOISE REDUCTION LEVEL 0: Fixed R L P P P 0 - R L R L P P RM READ METER 0: Depends on the front panel METER : ALC : S : PO : Depends on the front panel METER 6: SWR (PO / COMP / ALC / SWR / ID / VDD) 7: ID R M : COMP : VDD P 0 - R M P P P RS RADIO STATUS 0: NORMAL MODE : MENU MODE R S R S RT CLAR 0: RX Clariier OFF R T : RX Clariier ON R T R T RU RX CLARIFIER PLUS OFFSET (Hz) R U SC SCAN 0: Scan OFF S C : Scan ON (UP ward) : Scan ON (DOWN ward) S C S C

17 SD CW BREAK-IN DELAY TIME msec S D S D S D SH WIDTH 0: Fixed S H P P P 00 (See Table) S H S H P P Command Bandwidth P SSB (Narrow) SSB (Wide) CW (Narrow) CW (Wide) RTTY/PSK (Narrow) RTTY/PSK (Wide) 00 (Default) 00 Hz 00 Hz 00 Hz 00 Hz 00 Hz 00 Hz 0 00 Hz - 0 Hz - 0 Hz Hz - 00 Hz - 00 Hz Hz - 0 Hz - 0 Hz Hz - 00 Hz - 00 Hz Hz - 0 Hz - 0 Hz Hz - 00 Hz - 00 Hz Hz - 0 Hz - 0 Hz Hz - 00 Hz - 00 Hz Hz 00 Hz 0 Hz - 0 Hz Hz 00 Hz 00 Hz 00 Hz 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz Hz Hz - 00 Hz Hz Hz Hz - 00 Hz - 00 Hz Hz Hz Hz - 00 Hz Hz Hz Hz SM S-METER READING 0: Fixed P S M S M P P P SQ SQUELCLH LEVEL 0: Fixed S Q P P P P S Q S Q P P P SV SWAP VFO S V 6

18 TS TXW 0: TXW OFF T S : TXW ON T S T S TX TX SET 0: RADIO TX OFF CAT TX OFF T X : RADIO TX OFF CAT TX ON : RADIO TX ON CAT TX OFF () T X T X UL PLL UNLOCK STATUS 0: PLL Lock : PLL Unlock U L U L UP UP U P VD VOX DELAY TIME msec (0 msec multiples) V D V D V D VG VOX GAIN V G V G V G VM VFO-A TO MEMORY CHANNEL V M VX VOX STATUS 0: VOX OFF V X : VOX ON V X V X 7

19 XT TX CLAR 0: TX CLAR OFF X T : TX CLAR ON X T X T ZI ZERO IN (CW AUTO ZERO IN Function) Z I

20 Copyright 0 YAESU MUSEN CO., LTD. All rights reserved No portion of this manual may be reproduced without the permission of YAESU MUSEN CO., LTD. 0-A0

CAT Operation Reference Manual

CAT Operation Reference Manual CAT Operation Reference Manual YAESU MUSEN CO., LTD. Overview The CAT (Computer Aided Transceiver) System in the FT-99 transceiver provides control of frequency, VFO, memory, and other settings such as

More information

FT-891 YAESU MUSEN CO., LTD.

FT-891 YAESU MUSEN CO., LTD. FT- CAT Operation Reference Book YAESU MUSEN CO., LTD. Overview The CAT (Computer Aided Transceiver) System in the FT- transceiver provides control of frequency, VFO, memory, and other settings such as

More information

NOTE FTDX9000 CAT OPERATION REFERENCE BOOK FTDX9000 OPERATING MANUAL

NOTE FTDX9000 CAT OPERATION REFERENCE BOOK FTDX9000 OPERATING MANUAL NTE FTD9000 CAT PERATIN REFERENCE BK FTD9000 PERATING MANUAL CAT (CMPUTER AIDED TRANSCEIVR) PERATIN VERVIEW The CAT (Computer Aided Transceiver) System in the FTD9000 provides control of frequency, VF,

More information

FT-991 MENU MODE. changes in factory defaults are yellow

FT-991 MENU MODE. changes in factory defaults are yellow changes in factory defaults are yellow FT-991 MENU MODE No. Menu Function Available Settings Default Value 001 AGC FAST DELAY 20-4000 (20msec/step) 300msec 002 AGC MID DELAY 20-4000 (20msec/step) 700msec

More information

FT-991 Firmware Update Information

FT-991 Firmware Update Information FT-991 Firmware Update Information This update adds the DG-ID function and the DP-ID function in the digital C4FM mode of the FT- 991 and is compatible with the System Fusion II digital repeater DR-2X.

More information

FTDX3000 SERIES CAT OPERATION REFERENCE BOOK YAESU MUSEN CO., LTD.

FTDX3000 SERIES CAT OPERATION REFERENCE BOOK YAESU MUSEN CO., LTD. FTD3000 SERIES CAT PERATIN REFERENCE BK YAESU MUSEN C., LTD. CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver) System in the FTD3000 transceiver provides control of frequency,

More information

CAT (COMPUTER AIDED TRANSCEIVER) OPERATION

CAT (COMPUTER AIDED TRANSCEIVER) OPERATION CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FTD5000 SERIES CAT PERATIN REFERENCE BK FTD5000 SERIES CAT PERATIN REFERENCE CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver)

More information

CAT (COMPUTER AIDED TRANSCEIVER) OPERATION FT-450D CAT OPERATION YAESU MUSEN CO., LTD. FT-450D CAT OPERATION REFERENCE BOOK

CAT (COMPUTER AIDED TRANSCEIVER) OPERATION FT-450D CAT OPERATION YAESU MUSEN CO., LTD. FT-450D CAT OPERATION REFERENCE BOOK CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FT-450D CAT PERATIN REFERENCE BK YAESU MUSEN C., LTD. FT-450D CAT PERATIN REFERENCE BK CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver)

More information

CAT (COMPUTER AIDED TRANSCEIVER) OPERATION FT-950 CAT OPERATION FT-950 CAT OPERATION REFERENCE BOOK

CAT (COMPUTER AIDED TRANSCEIVER) OPERATION FT-950 CAT OPERATION FT-950 CAT OPERATION REFERENCE BOOK CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FT-950 CAT PERATIN REFERENCE BK FT-950 CAT PERATIN REFERENCE BK CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver) System in the

More information

TS-590S TS-590SG. PC CONTROL COMMAND Reference Guide

TS-590S TS-590SG. PC CONTROL COMMAND Reference Guide TS-590S TS-590SG PC CONTROL COMMAND Reference Guide January/30/2019 PC CONTROL COMMAND REFERENCE GUIDE ABOUT THIS REFERENCE GUIDE All descriptions in this reference guide are for the user s convenience.

More information

CAT (COMPUTER AIDED TRANSCEIVER) OPERATION

CAT (COMPUTER AIDED TRANSCEIVER) OPERATION CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FT-2000 SERIES CAT PERATIN REFERENCE BK FT-2000 SERIES CAT PERATIN REFERENCE BK CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver)

More information

CAT (COMPUTER AIDED TRANSCEIVER) OPERATION

CAT (COMPUTER AIDED TRANSCEIVER) OPERATION CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FT D 9000 SERIES CAT PERATIN REFERENCE BK FT D 9000 SERIES CAT PERATIN REFERENCE CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver)

More information

SPECS FEATURES SUPPLIED ACCESSORIES. HF All Band Transceiver

SPECS FEATURES SUPPLIED ACCESSORIES. HF All Band Transceiver 718 HF All Band Transceiver RX 0.030-29.999999MHz* TX 1.800-1.999999 MHz** 3.500-3.999999 MHz** 7.000-7.300000 MHz 10.100-10.150000 MHz 14.000-14.350000 MHz 18.068-18.168000 MHz 21.000-21.450000 MHz 24.890-24.990000

More information

LnR Precision, Inc. 107 East Central Avenue, Asheboro, NC

LnR Precision, Inc. 107 East Central Avenue, Asheboro, NC LD5 CW/SSB QRP Transceiver Quick guide manual Description: At the development base of the digital signal processing unit, an algorithm is embedded for IQ processing of the channels with phase suppression

More information

The Icom IC Adam Farson VA7OJ. A New Top-class HF/6m Transceiver. IC-7700 Information & Links

The Icom IC Adam Farson VA7OJ. A New Top-class HF/6m Transceiver. IC-7700 Information & Links The Icom IC-7700 A New Top-class HF/6m Transceiver Adam Farson VA7OJ IC-7700 Information & Links Copyright 2008 North Shore Amateur Radio Club NSARC HF Operators IC-7700 1 IC-7700 front panel This is a

More information

Icom IC-9100 HF/VHF/UHF transceiver

Icom IC-9100 HF/VHF/UHF transceiver 263 Walsall Road, Great Wyrley, Walsall, WS6 6DL Established 1997. Open Monday - Friday 9am - 5pm and Saturday 9.30am - 4pm Tel: 01922 414 796 Fax: 01922 417829 Skype: radioworld_uk Icom IC-9100 HF/VHF/UHF

More information

LD5 CW/SSB QRP Transceiver SDR /DSP

LD5 CW/SSB QRP Transceiver SDR /DSP LD5 CW/SSB QRP Transceiver SDR /DSP Quick guide manual Description: At the development base of the digital signal processing unit, an algorithm is embedded for IQ processing of the channels with phase

More information

FT-897 Alignment. Local Oscillator Adjustment. PLL Adjustment

FT-897 Alignment. Local Oscillator Adjustment. PLL Adjustment FT-897 Local Oscillator Adjustment Reference Frequency Adjustment a. Connect a frequency counter to TP1032. b. Adjust the trimmer capacitor (TC5001) for 67.875000MHz ±5Hz on the frequency counter. c. Connect

More information

CI-V REFERENCE GUIDE. HF/50MHz TRANSCEIVER. i7610

CI-V REFERENCE GUIDE. HF/50MHz TRANSCEIVER. i7610 CI-V REFERENCE GUIDE HF/50MHz TRANSCEIVER i7610 Table of contents Remote control 2 Remote control (CI-V) information 2 DDCI-V connection 2 DDPreparing 2 DDAbout the data format 2 DDCommand table 3 DDCommand

More information

MENU MODE USING THE MENU FT-950 OPERATING MANUAL

MENU MODE USING THE MENU FT-950 OPERATING MANUAL The Menu system of the FT-950 provides extensive customization capability, so you can set up your transceiver just the way you want to operate it. The Menu items are grouped by general utilization category,

More information

Technician License Course Chapter 5. Lesson Plan Module 11 Transmitters, Receivers and Transceivers

Technician License Course Chapter 5. Lesson Plan Module 11 Transmitters, Receivers and Transceivers Technician License Course Chapter 5 Lesson Plan Module 11 Transmitters, Receivers and Transceivers Generalized Transceiver Categories Mobile Single Band Dual Band All Band Multimode Handheld (HT) VHF/UHF

More information

TS-890S. PC CONTROL COMMAND Reference Guide

TS-890S. PC CONTROL COMMAND Reference Guide TS-890S PC CONTROL COMMAND Reference Guide August/30/2018 PC CONTROL COMMAND REFERENCE GUIDE ABOUT THIS REFERENCE GUIDE All descriptions in this reference guide are for the user s convenience. JVC KENWOOD

More information

IC-400pro - RADIOAFICION.COM

IC-400pro - RADIOAFICION.COM PROCEDURES IC-400pro - 5- PREPARATION When you adjust the contents on pages 5-5 and 5-6, SOFT- WARE, the optional CS-400PRO ADJ SOFTWARE (Rev..0 or later), *OPC- JIG CABLE (modified OPC- CLONING CABLE;

More information

Kenwood TH-G71 Protocol Specification

Kenwood TH-G71 Protocol Specification Kenwood TH-G71 Protocol Specification This document describes the serial commands used to program and control the TH-G71 radio via its serial port. Some of this data was initially based on information

More information

KENWOOD SKY COMMAND SYSTEM

KENWOOD SKY COMMAND SYSTEM KENWOOD SKY COMMAND SYSTEM Operation Manual KENWOOD COMMINICATIONS CORPORATION KENWOOD COMMUNICATIONS CORPORATION This operation manual is used for the KENWOOD SKY COMMAND SYSTEM (hereinafter referred

More information

Elmer Session Hand Out for 3/3/11 de W6WTI. Some Common Controls Found On Amateur Radio Transceivers. (From ARRL web site tutorial)

Elmer Session Hand Out for 3/3/11 de W6WTI. Some Common Controls Found On Amateur Radio Transceivers. (From ARRL web site tutorial) Elmer Session Hand Out for 3/3/11 de W6WTI Some Common Controls Found On Amateur Radio Transceivers. (From ARRL web site tutorial) The placement of the controls may vary from manufacturer to manufacturer

More information

FT-991. HF/VHF/UHF All Mode Transceiver

FT-991. HF/VHF/UHF All Mode Transceiver HF/VHF/UHF All Mode Transceiver FT-991 Operating Manual YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress,

More information

GRAND STRAND AMATEUR RADIO CLUB

GRAND STRAND AMATEUR RADIO CLUB The GRAND STRAND AMATEUR RADIO CLUB (GSARC) Myrtle Beach SC is offering used amateur related equipment for sale. Written bids may be submitted to the GSARC up to Friday, November 23 rd, 2018. Only currently

More information

i746 INSTRUCTION MANUAL VHF/HF ALL MODE TRANSCEIVER

i746 INSTRUCTION MANUAL VHF/HF ALL MODE TRANSCEIVER INSTRUCTION MANUAL VHF/HF ALL MODE TRANSCEIVER i746 This device complies with Part 5 of the FCC rules. Operation is subject to the following two conditions: () This device may not cause harmful interference,

More information

i78 INSTRUCTION MANUAL HF TRANSCEIVER

i78 INSTRUCTION MANUAL HF TRANSCEIVER INSTRUCTION MANUAL HF TRANSCEIVER i78 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)

More information

The amazing evolution of the 706 series

The amazing evolution of the 706 series The amazing evolution of the 706 series The IC-706MKIIG carries on the 706 series tradition of base station performance and features in a mobile reg-sized package. Building on this legacy, frequency coverage

More information

SERIAL INPUT AND SERIAL OUTPUT These ports are used for communications between the main CPU (controller) and the sub CPU.

SERIAL INPUT AND SERIAL OUTPUT These ports are used for communications between the main CPU (controller) and the sub CPU. IC-901 CPU SERIAL DATA CONTROL SERIAL INPUT AND SERIAL OUTPUT These ports are used for communications between the main CPU (controller) and the sub CPU. When the operation interrupt START BIT is applied

More information

WIRES-X Portable Digital Node Function. Instruction Manual

WIRES-X Portable Digital Node Function. Instruction Manual Wide-Coverage Internet Repeater Enhancement System WIRES-X Portable Digital Node Function Instruction Manual Please read this Instruction Manual carefully for appropriate procedure. Preparation Procedure

More information

Frequency Coverage MHz RF Power Output 30W SSB / 9W AM/ 30W FM Dual Finals on Heat Sink Modes AM, FM, USB, LSB Microprocessor

Frequency Coverage MHz RF Power Output 30W SSB / 9W AM/ 30W FM Dual Finals on Heat Sink Modes AM, FM, USB, LSB Microprocessor MAGNUM M-257 30W AM/ /FM/SSB 10--11 Meterr Mobile Trranscei ivverr n Prri iiccee: : US$ 250..00 eexx ssttoocckk JJaakkaarrttaa (Arrrri ( iivvi iinngg 2 d weeeekk iinn i Maarrcchh) ) SPECIFICATIONS Frequency

More information

TS-590S ADJUSTMENT. Updating the Firmware. Required Test Equipment. Preparation

TS-590S ADJUSTMENT. Updating the Firmware. Required Test Equipment. Preparation Updating the Firmware The firmware of the main MCU and DSP can be updated using the TS590 Update update software. Update the firmware according to the procedure displayed in update software. Refer to the

More information

Yaesu FT-991A HF, VHF, and UHF Transceiver

Yaesu FT-991A HF, VHF, and UHF Transceiver Mark J. Wilson, K1RO, k1ro@arrl.org Product Review Yaesu FT-991A HF, VHF, and UHF Transceiver Reviewed by Joel R. Hallas, W1ZR QST Contributing Editor w1zr@arrl.org The FT-991A is a compact SSB, CW, AM,

More information

WIRES-X Portable Digital Node Function. Instruction Manual

WIRES-X Portable Digital Node Function. Instruction Manual Wide-Coverage Internet Repeater Enhancement System WIRES-X Portable Digital Node Function Instruction Manual Please read this Instruction Manual carefully for appropriate procedure. Preparation Procedure

More information

Before using your FT-950, be sure to read and follow the instructions in the Before You Begin section of this manual.

Before using your FT-950, be sure to read and follow the instructions in the Before You Begin section of this manual. About This Manual... The FT-950 is a leading-edge transceiver with a number of new and exciting features, some of which may be unfamiliar to you. In order to gain the most enjoyment and operating efficiency

More information

DJ-MD5 PC Software Guidance

DJ-MD5 PC Software Guidance DJ-MD5 PC Software Guidance Ver, 1.00 2018/08/16 1 Appendix I Public... 4 1. Channel... 4 1 Frequency, call type, power... 4 2 Digital Channel Setting... 5 3 Analog Channel Setting... 6 2. Zone... 7 3.

More information

Application for FCC / IC FCC ID: K X50 IC: 511B HF/50 MHz Transceiver FT-410 Operation Manual YAESU MUSEN CO., LTD. Tennozu Parkside Build

Application for FCC / IC FCC ID: K X50 IC: 511B HF/50 MHz Transceiver FT-410 Operation Manual YAESU MUSEN CO., LTD. Tennozu Parkside Build HF/50 MHz Transceiver FT-410 Operation Manual YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress, CA 90630,

More information

THE TRANSCEIVER Instruction Manual

THE TRANSCEIVER Instruction Manual THE TRANSCEIVER i7800 Instruction Manual A-6328H-1EX-q Printed in Japan 2004 Icom Inc. FOREWORD Congratulations! You are the owner of the world s most advanced amateur HF/50 MHz transceiver IC-7800. The

More information

FT-991. HF/VHF/UHF All Mode Transceiver

FT-991. HF/VHF/UHF All Mode Transceiver HF/VHF/UHF All Mode Transceiver FT-991 Operating Manual YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress,

More information

Pushing performance to the pinnacle

Pushing performance to the pinnacle Pushing performance to the pinnacle The latest DSP technologies developed for the IC-7800/7700 plus over 45 years of analog circuit expertise give the IC-7600 the performance advantage. The flagship's

More information

Disable Windows Sounds

Disable Windows Sounds 9/28/2017 - K3CT Disable Windows Sounds Users may want to disable the Windows Sounds so none of the Windows OS sounds are transmitted on the radio. Install the Icom Drivers, Select COM port, Disable Power

More information

HF/VHF/UHF ALL MODE TRANSCEIVER FT-818

HF/VHF/UHF ALL MODE TRANSCEIVER FT-818 HF/VHF/UHF ALL MODE TRANSCEIVER FT-818 Operating Manual Contents Introduction...1 Accessories & Options...2 Supplied Accessories...2 Available Options...2 Plug Pinout...3 Installation...4 Connecting the

More information

MENU MODE USING THE MENU FT-2000 OPERATING MANUAL. Menu Mode Reset

MENU MODE USING THE MENU FT-2000 OPERATING MANUAL. Menu Mode Reset The Menu system of the FT-2000 provides extensive customization capability, so you can set up your transceiver just the way you want to operate it. The Menu items are grouped by general utilization category,

More information

INSTRUCTION MANUAL REMOTE CONTROL SOFTWARE RS-R75

INSTRUCTION MANUAL REMOTE CONTROL SOFTWARE RS-R75 INSTRUCTION MANUAL REMOTE CONTROL SOFTWARE RS-R75 IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the receiver. SAVE THIS INSTRUCTION MANUAL This instruction manual contains important

More information

Reference for UV-5R Menus by Jim Unroe - KC9HI 2-April-2014

Reference for UV-5R Menus by Jim Unroe - KC9HI 2-April-2014 Long Name / Description / / Notes / 0 SQL Carrier Squelch Mutes the speaker of the transceiver in the absence of a strong signal. VHF squelch is either OFF or ON. UHF squelch is either OFF or one of 9

More information

Development of the QSX transceiver kit

Development of the QSX transceiver kit Development of the QSX transceiver kit Norfolk Amateur Radio Club Wednesday 9-Jan-2019 Hans Summers, G0UPL http://qrp-labs.com QCX 5W CW transceiver kit QRP Labs CW Xcvr Introduced at YOTA 2017 summercamp

More information

TS-590S INSTRUCTION MANUAL. HF/ 50 MHz ALL MODE TRANSCEIVER

TS-590S INSTRUCTION MANUAL. HF/ 50 MHz ALL MODE TRANSCEIVER INSTRUCTION MANUAL HF/ 50 MHz ALL MODE TRANSCEIVER TS-590S NOTIFICATION This equipment complies with the essential requirements of Directive 1999/5/EC. The use of the warning symbol means the equipment

More information

BLOCK DIAGRAM - I J Li) N 6. w IS) AF D RIVE R R F D RIVE R R F P OWE R AMP PL L OSC UNIT. LL co X X X Lti X. C X W N O C..) 4 C.

BLOCK DIAGRAM - I J Li) N 6. w IS) AF D RIVE R R F D RIVE R R F P OWE R AMP PL L OSC UNIT. LL co X X X Lti X. C X W N O C..) 4 C. MODEL 1-632 BLOCK DIAGRAM tl LL co a. LL O ox X X X X < X C.) W N C U) LL CO aa 1.11 t O - I J Ul Li) Lti N w IS) 1 X. C X Ir t AF D RIVE R X - LL C.) CD r.--1111 MOP U) N N 6 PL L OSC UNIT R F D RIVE

More information

Second Hand Yaesu FTDX5000MP HF base station transceiver

Second Hand Yaesu FTDX5000MP HF base station transceiver 263 Walsall Road, Great Wyrley, Walsall, WS6 6DL Established 1997. Open Monday - Friday 9am - 5pm and Saturday 9.30am - 4pm Tel: 01922 414 796 Fax: 01922 417829 Skype: radioworld_uk Second Hand Yaesu FTDX5000MP

More information

INSTALLATION AND CONNECTIONS Section 2

INSTALLATION AND CONNECTIONS Section 2 STLLTION ND CONNECTIONS Section Unpacking - ntenna jumper cable connection - Selecting a location - Rack mounting handle attachment - Grounding -3 ntenna connection -3 CF (Compact Flash) memory card -3

More information

INSTRUCTION MANUAL. HF/ 50 MHz ALL MODE TRANSCEIVER TS-590S

INSTRUCTION MANUAL. HF/ 50 MHz ALL MODE TRANSCEIVER TS-590S INSTRUCTION MANUAL HF/ 50 MHz ALL MODE TRANSCEIVER TS-590S NOTIFICATION This equipment complies with the essential requirements of Directive 1999/5/EC. The use of the warning symbol means the equipment

More information

Ten-Tec Orion/Orion II Users Manual Addendum Firmware Version V3

Ten-Tec Orion/Orion II Users Manual Addendum Firmware Version V3 Ten-Tec Orion/Orion II Users Manual Addendum Firmware Version V3 It is very important that you read this document in its entirety before using the V3 firmware. Some features behave differently than they

More information

i7851 Firmware information Ver. 1.10

i7851 Firmware information Ver. 1.10 i7851 Firmware information Ver. 1.10 Thank you for using the Icom Download Service. The Version 1.10 firmware update will provide the following additional functions or changes to your transceiver. The

More information

Adjustment for IC-910H. Adjustment. Adjustment

Adjustment for IC-910H. Adjustment. Adjustment for IC-910H 30.2 MHz Level 430MHz 2 nd Lo (60.4MHz) Peak Setting the 60.4MHz Frequency the144mhz 1 st Lo Lock Voltage th430mhz 1 st Lo Lock Voltage 144MHz RX Peak/ Gain Band Peak Band Total Gain Sub- Band

More information

FT-450 OPERATION MANUAL HF/50 MHZ TRANSCEIVER

FT-450 OPERATION MANUAL HF/50 MHZ TRANSCEIVER HF/50 MHZ TRANSCEIVER FT-450 OPERATION MANUAL VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A.

More information

HF/50MHz TRANSCEIVER

HF/50MHz TRANSCEIVER HF/50MHz TRANSCEIVER D isplay Pushing performance to the pinnacle The latest DSP technologies developed for the flagship models plus many decades of analog circuit expertise give the the performance advantage.

More information

Wayne Burdick, N6KR Rev. A3, Applies to firmware revision 2.61 or later.

Wayne Burdick, N6KR Rev. A3, Applies to firmware revision 2.61 or later. ELECRAFT KX2 PHYSICAL DESCRIPTION AND AUDIO-CW USER INTERFACE Wayne Burdick, N6KR Rev. A3, 5-31-2016 Applies to firmware revision 2.61 or later. CHANGE HISTORY Rev. A1, 5-23-2016: Document creation. Rev.

More information

INSTRUCTION MANUAL. HF/50 MHz TRANSCEIVER. i7410

INSTRUCTION MANUAL. HF/50 MHz TRANSCEIVER. i7410 INSTRUCTION MANUAL HF/0 MHz TRANSCEIVER i0 i FOREWORD Thank you for making the IC-0 your radio of choice. We hope you agree with Icom s philosophy of technology first. Many hours of research and development

More information

SEA 235 OPERATOR S MANUAL Digital Single Sideband Radiotelephone

SEA 235 OPERATOR S MANUAL Digital Single Sideband Radiotelephone SEA 235 OPERATOR S MANUAL Digital Single Sideband Radiotelephone TABLE OF CONTENTS GENERAL OPERATIONS...1 TECHNICAL SPECIFICATIONS...1 GENERAL INFORMATION...2 UNDERSTANDING CHANNEL MEMORY...3 LCD DISPLAY

More information

INSTRUCTION MANUAL. 144/ 430 MHz FM DUAL BANDER TH-F7A B (M) FM DUAL BANDER TH-F7

INSTRUCTION MANUAL. 144/ 430 MHz FM DUAL BANDER TH-F7A B (M) FM DUAL BANDER TH-F7 INSTRUCTION MANUAL FM DUAL BANDER TH-F7 144/ 430 MHz FM DUAL BANDER TH-F7A B62-1899-00 (M) 09 08 07 06 05 04 03 02 01 00 THANK YOU THANK YOU Thank you for choosing this KENWOOD TH-F7A transceiver. It has

More information

AM/FM/SSB/CW 12 & 10 METER MOBILE AMATEUR TRANSCEIVER OWNER S MANUAL

AM/FM/SSB/CW 12 & 10 METER MOBILE AMATEUR TRANSCEIVER OWNER S MANUAL AM/FM/SSB/CW 12 & 10 METER MOBILE AMATEUR TRANSCEIVER OWNER S MANUAL TABLE OF CONTENTS Warranty...2 Introduction...3 Installation... 4-5 Front Panel Controls... 6-8 Microphone...8 Menu Settings... 9-11

More information

Chapter 15: Serial Controlled (HF) Radio Support

Chapter 15: Serial Controlled (HF) Radio Support 15-1 Chapter 15: Serial Controlled (HF) Radio Support This section describes the controller's interface for serial controlled radios. Most such radios are for the HF bands, but some such as the FT-736

More information

INSTRUCTION MANUAL. Version: /440 MHz FM DUAL BANDER TM-D710GA. 144/430 MHz FM DUAL BANDER TM-D710GE

INSTRUCTION MANUAL. Version: /440 MHz FM DUAL BANDER TM-D710GA. 144/430 MHz FM DUAL BANDER TM-D710GE INSTRUCTION MANUAL 144/440 MHz FM DUAL BANDER TM-D710GA 144/430 MHz FM DUAL BANDER TM-D710GE Version: 1.01 CONTENTS OPERATING THROUGH REPEATERS...REPEATER- REPEATER ACCESS... 1 Selecting an Offset Direction...

More information

INSTRUCTION MANUAL. Version: /440 MHz FM DUAL BANDER TM-D710GA. 144/430 MHz FM DUAL BANDER TM-D710GE

INSTRUCTION MANUAL. Version: /440 MHz FM DUAL BANDER TM-D710GA. 144/430 MHz FM DUAL BANDER TM-D710GE INSTRUCTION MANUAL 144/440 MHz FM DUAL BANDER TM-D710GA 144/430 MHz FM DUAL BANDER TM-D710GE Version: 1.00 CONTENTS OPERATING THROUGH REPEATERS...REPEATER- REPEATER ACCESS... 1 Selecting an Offset Direction...

More information

INSTRUCTION MANUAL VHF/UHF ALL MODE TRANSCEIVER. i910h

INSTRUCTION MANUAL VHF/UHF ALL MODE TRANSCEIVER. i910h INSTRUCTION MANUAL VHF/UHF ALL MODE TRANSCEIVER i910h IMPORTANT EXPLICIT DEFINITIONS READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the transceiver. SAVE THIS INSTRUCTION MANUAL. This

More information

INSTRUCTION MANUAL ALL MODE MULTI-BAND TRANSCEIVER TS-2000 TS-2000X TS-B2000

INSTRUCTION MANUAL ALL MODE MULTI-BAND TRANSCEIVER TS-2000 TS-2000X TS-B2000 B6--50 (K, E) 09 08 07 06 05 ALL MODE MULTI-BAND TRANSCEIVER TS-000 TS-000X TS-B000 INSTRUCTION MANUAL NOTIFICATION This equipment complies with the essential requirements of Directive 999/5/EC. The use

More information

AT-D868UV CodePlug Programming Guide

AT-D868UV CodePlug Programming Guide INTRODUCTION The AnyTone D868UV radio is a VHF and UHF radio with both Digital DMR (Tier I and II) and Analog capabilities. It offers a total of 4,000 channels (Analog and Digital) and up to 130,000 contacts,

More information

ELAD FDM-DUO Dual Mode SDR Transceiver USER MANUAL

ELAD FDM-DUO Dual Mode SDR Transceiver USER MANUAL ELAD FDM-DUO Dual Mode SDR Transceiver USER MANUAL www.eladit.com Contents Revision History... 4 1 Overview... 5 1.1 Notice... 5 1.2 Firmware versions... 5 1.3 Introduction... 5 1.3.1 Main Features...

More information

INSTRUCTION MANUAL. HF/50 MHz TRANSCEIVER. i7200

INSTRUCTION MANUAL. HF/50 MHz TRANSCEIVER. i7200 INSTRUCTION MANUAL HF/ MHz TRANSCEIVER i IMPORTANT R E A D T H I S I N S T RU C T I O N M A N UA L CAREFULLY before attempting to operate the transceiver SAVE THIS INSTRUCTION MANUAL This manual contains

More information

i7610 Technical Report Volume 1

i7610 Technical Report Volume 1 i7610 Technical Report Volume 1 ~ Profile ~ Outstanding HF Experience Right Here Icom s mid class HF transceivers evolved especially with the IC-756, IC- 756PRO and IC-7600, and were technology leaders

More information

Cat. No OWNER S MANUAL. HTX-212 Two-Meter Mobile Transceiver. Please read before using this transceiver.

Cat. No OWNER S MANUAL. HTX-212 Two-Meter Mobile Transceiver. Please read before using this transceiver. 19-1125.fm Page 1 Tuesday, August 3, 1999 9:47 AM Cat. No. 19-1125 OWNER S MANUAL HTX-212 Two-Meter Mobile Transceiver Please read before using this transceiver. 19-1125.fm Page 2 Tuesday, August 3, 1999

More information

FT-950 OPERATING MANUAL HF/50 MHZ TRANSCEIVER

FT-950 OPERATING MANUAL HF/50 MHZ TRANSCEIVER HF/50 MHZ TRANSCEIVER FT-950 OPERATING MANUAL VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A.

More information

i7610 Technical Report Volume 1

i7610 Technical Report Volume 1 i7610 Technical Report Volume 1 ~ Profile ~ Outstanding HF Experience Right Here Icom s mid class HF transceivers evolved especially with the IC-756, IC756PRO and IC-7600, and were technology leaders in

More information

BAND DECODER and CONTROLLE R. Accessibility Upgrade and Operating Instructions

BAND DECODER and CONTROLLE R. Accessibility Upgrade and Operating Instructions ELE CRAFT KRC2 BAND DECODER and CONTROLLE R Accessibility Upgrade and Operating Instructions Revision A, March 4, 2004. Copyright 2004, Elecraft; All Rights Reserved Introduction The KRC2 Accessibility

More information

TS-590SG HF/ 50MHz All-Mode TRANSCEIVER_

TS-590SG HF/ 50MHz All-Mode TRANSCEIVER_ New Product Release Information Oct 2014 TS-590SG HF/ 50MHz All-Mode TRANSCEIVER_ Kenwood introduces Updated to new G version new HF/50MHz All-Mode Transceiver Four years ago we launched our best-selling

More information

THANK YOU FOR YOUR PURCHASE OF THE UV THIS DUAL BAND RADIO WILL DELIVER TO YOU SECURE INSTANT RELIABLE COMMUNICATION.

THANK YOU FOR YOUR PURCHASE OF THE UV THIS DUAL BAND RADIO WILL DELIVER TO YOU SECURE INSTANT RELIABLE COMMUNICATION. Copyright 2016 by BTECH; https://baofengtech.com All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording,

More information

JUMA-TRX2 DDS / Control Board description OH2NLT

JUMA-TRX2 DDS / Control Board description OH2NLT JUMA-TRX2 DDS / Control Board description OH2NLT 22.08.2007 General Key functions of the JUMA-TRX2 DDS / Control board are: - provide user interface functions with LCD display, buttons, potentiometers

More information

FTDX5000 SERIES OPERATING MANUAL HF/50 MHZ TRANSCEIVER

FTDX5000 SERIES OPERATING MANUAL HF/50 MHZ TRANSCEIVER HF/50 MHZ TRANSCEIVER FTDX5000 SERIES OPERATING MANUAL VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD U.S.A. Inc. 6125 Phyllis Drive, Cypress, California 90630,

More information

SUBELEMENT T4. Amateur radio practices and station set up. 2 Exam Questions - 2 Groups

SUBELEMENT T4. Amateur radio practices and station set up. 2 Exam Questions - 2 Groups SUBELEMENT T4 Amateur radio practices and station set up 2 Exam Questions - 2 Groups 1 T4A Station setup: connecting microphones; reducing unwanted emissions; power source; connecting a computer; RF grounding;

More information

ISOTERM-MULTICON USB TRAVELLER

ISOTERM-MULTICON USB TRAVELLER ISOTERM-MULTICON USB TRAVELLER SETTING UP INSTRUCTIONS FOR DATA INTERFACE de G3LIV Welcome to the World of PSK-31. Thank you for purchasing this ISOTERM USB interface. I hope it will give you hours of

More information

INSTRUCTION MANUAL CONTROL PANEL RC-D710. Version: 2.10

INSTRUCTION MANUAL CONTROL PANEL RC-D710. Version: 2.10 INSTRUCTION MANUAL CONTROL PANEL RC-D710 Version: 2.10 CONTENTS File name (TM-D710_) Operation OPERATING THROUGH REPEATERS...REPEATER- 01_REPEATER_E.pdf OPERATING THROUGH REPEATERS...1 REPEATER ACCESS...1

More information

ISOTERM-MULTICON TRAVELLER

ISOTERM-MULTICON TRAVELLER ISOTERM-MULTICON TRAVELLER SETTING UP INSTRUCTIONS FOR DATA INTERFACE de G3LIV July 2012 Page 1-1 Welcome to the World of PSK-31. Thank you for purchasing this ISOTERM. I hope it will give you hours of

More information

CONTENTS. Operation File name (TH-D72_) CONTENTS 1 OPERATING THROUGH REPEATERS... REPEATER. 01_REPEATER_E.pdf MEMORY CHANNELS...

CONTENTS. Operation File name (TH-D72_) CONTENTS 1 OPERATING THROUGH REPEATERS... REPEATER. 01_REPEATER_E.pdf MEMORY CHANNELS... CONTENTS Operation File name (TH-D72_) OPERATING THROUGH REPEATERS... REPEATER REPEATER ACCESS... 1 Selecting an Offset Direction... 1 Selecting an Offset Frequency... 1 Activating the Tone Function...

More information

Amateur Station Control Protocol (ASCP) Ver Oct. 5, 2002

Amateur Station Control Protocol (ASCP) Ver Oct. 5, 2002 Amateur Station Control Protocol (ASCP) Ver. 0.17 Oct. 5, 2002 Moe Wheatley, AE4JY Table of Contents 1. Purpose...4 2. Basic Protocol Concepts...5 3. Message Block Format...8 3.1. Detailed Description

More information

RigExpert TI-7 USB Transceiver Interface User s manual

RigExpert TI-7 USB Transceiver Interface User s manual RigExpert TI-7 USB Transceiver Interface User s manual Please read this manual before attempting to use the RigExpert TI-7 device. - - 2 - Table of contents 1. What is a RigExpert TI-7?... 4 2. Specifications...

More information

RM Italy HLA-305V HF Amplifier Test Report

RM Italy HLA-305V HF Amplifier Test Report RM Italy HLA-305V HF Amplifier Test Report By Adam Farson VA7OJ/AB4OJ P.O. Box 91105, West Vancouver BC V7V 3N3, Canada Iss. 2, April 30, 2015 Figure 1: HLA-305V HF Amplifier, with cooling fans.. Introduction:

More information

LNR Precision Mountain Topper MTR-4B and MTR-5B REV 2.0 User Manual for use with versions with 16 x 2 display.

LNR Precision Mountain Topper MTR-4B and MTR-5B REV 2.0 User Manual for use with versions with 16 x 2 display. LNR Precision Mountain Topper MTR-4B and MTR-5B REV 2.0 User Manual for use with versions with 16 x 2 display. Four band MTR 4B shown Overview: The Mountain Topper Rigs are designed to be a very small,

More information

XIEGU COMMUNICATION X5105. HF+50MHz Portable HF Transceiver. Instruction Manual. Chongqing Xiegu Technology Co.,Ltd.

XIEGU COMMUNICATION X5105. HF+50MHz Portable HF Transceiver. Instruction Manual. Chongqing Xiegu Technology Co.,Ltd. XIEGU COMMUNICATION X5105 HF+50MHz Portable HF Transceiver Instruction Manual Chongqing Xiegu Technology Co.,Ltd. www.cqxiegu.com Important reminder: Before operating the equipment, please Security considerations:

More information

ID-5100 User Evaluation & Test Report

ID-5100 User Evaluation & Test Report ID-5100 User Evaluation & Test Report By Adam Farson VA7OJ/AB4OJ Iss. 1, August 13, 2014. Part I: Brief User Evaluation. Introduction: This report describes the evaluation and lab test of ID-5100 S/N 05001175.

More information

THANK YOU FOR YOUR PURCHASE OF THE UV THIS DUAL BAND RADIO WILL DELIVER TO YOU SECURE INSTANT RELIABLE COMMUNICATION.

THANK YOU FOR YOUR PURCHASE OF THE UV THIS DUAL BAND RADIO WILL DELIVER TO YOU SECURE INSTANT RELIABLE COMMUNICATION. Copyright 2016 by BTECH; https://baofengtech.com All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording,

More information

Yaesu FT-25R 2-Meter Handheld Transceiver

Yaesu FT-25R 2-Meter Handheld Transceiver Yaesu FT-25R 2-Meter Handheld Transceiver Reviewed by Dan Wall, W1ZFG ARRL LoTW Administration w1zfg@arrl.org The latest entry into the field of small, inexpensive handhelds is the Yaesu FT-25R. This is

More information

ADVANCED MANUAL. VHF/UHF ALL MODE TRANSCEIVER i9700 INTRODUCTION 1 ADVANCED OPERATIONS 2 RECORD AND PLAYBACK 3 TX VOICE MEMORY 4 MEMORY CHANNEL 5 SCAN

ADVANCED MANUAL. VHF/UHF ALL MODE TRANSCEIVER i9700 INTRODUCTION 1 ADVANCED OPERATIONS 2 RECORD AND PLAYBACK 3 TX VOICE MEMORY 4 MEMORY CHANNEL 5 SCAN ADVANCED MANUAL VHF/UHF ALL MODE TRANSCEIVER i9700 INTRODUCTION 1 ADVANCED OPERATIONS 2 RECORD AND PLAYBACK 3 TX VOICE MEMORY 4 MEMORY CHANNEL 5 SCAN 6 OTHER FUNCTIONS 7 GPS OPERATION (BASIC) 8 GPS OPERATION

More information

Basic Transceiver tests with the 8800S

Basic Transceiver tests with the 8800S The most important thing we build is trust ADVANCED ELECTRONIC SOLUTIONS AVIATION SERVICES COMMUNICATIONS AND CONNECTIVITY MISSION SYSTEMS Basic Transceiver tests with the 8800S Basic Interconnects Interconnect

More information

YAESU MUSEN CO., LTD.

YAESU MUSEN CO., LTD. HRI-200 Reference Manual for DR-2X/XE This Reference Manual is for the DR-2X/XE. YAESU MUSEN CO., LTD. Activate HRI mode Change the repeater mode to the HRI mode 1. Turn the DR-2X/XE power OFF. 2. While

More information

FT-2000D OPERATING MANUAL HF/50 MHZ TRANSCEIVER

FT-2000D OPERATING MANUAL HF/50 MHZ TRANSCEIVER HF/50 MHZ TRANSCEIVER FT-2000D OPERATING MANUAL VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A.

More information

TABLE OF CONTENTS 8 SOFTWARE MENU MODE SETTINGS SOFTWARE MENU QUICK GUIDE SERVICE MODE... 24

TABLE OF CONTENTS 8 SOFTWARE MENU MODE SETTINGS SOFTWARE MENU QUICK GUIDE SERVICE MODE... 24 1 TABLE OF CONTENTS 1. TABLE OF CONTENTS......................... 2 2. INTRODUCTION............................. 3 3. SPECIFICATIONS............................ 4 4. ACCESSORY PACKAGE.......................

More information

INSTRUCTION MANUAL. HF/VHF ALL MODE TRANSCEIVER i746pro

INSTRUCTION MANUAL. HF/VHF ALL MODE TRANSCEIVER i746pro INSTRUCTION MANUAL HF/VHF ALL MODE TRANSCEIVER i746pro This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

More information