Soğutmada büyük beden modası

Transcription

1 Soğutmada büyük beden modası. W Yüksek kapasiteli soğutma yükleri, yüksek verimli ve daha gelişmiş teknolojili fanlar gerektirir, örneğin 50 mm çapa sahip performansı da çapı ile orantılı WGZ50 aksiyel fanımız gibi. GreenTech EC teknolojisinin verimliliği, son derece düşük ses seviyesi, basit kontrol arayüzü ve olağanüstü kullanım ömrü sayesinde XXL fanımız diğer alternatiflerin çok ötesindedir. Üstün motor teknolojisi ve ileri aerodinamik dizaynı bir araya getiren ebmpapst, ihtiyaçlarınızı size tek bir üründe sunmaktadır. Sizin yapmanız gereken ise ürünü kutusundan çıkarıp, çalıştırmak ve arkanıza yaslanıp keyfini çıkartmaktır. Partner of akantel ebmpapst 0007 Sk. No.6.O.S.. Çiğli - İZMİR Tel.: ( Pbx ) Fax : e-posta : akantel@akantel.com.tr / satis@akantel.com.tr

2 EC axial fans Ø 50 Material: Guard grille: Steel, phosphated and coated in black plastic Wall ring: Sheet steel, pre-galvanised and coated in black plastic lades: Die-cast aluminium Rotor: Coated in black Electronics enclosure: Die-cast aluminium, coated in black Number of blades: 5 Direction of rotation: clockwise, seen on rotor Type of protection: IP 5 Insulation class: "F" Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request Condensate discharges: Rotor-side Mode of operation: Continuous operation (S) earings: Maintenance-free ball bearings Nominal data lade angle Curve Nominal voltage range Frequency Speed/rpm () Max. input power () Max. current draw () Max. operative range Perm. amb. temp. Mass without attachments Technical features and electr. connections Type Motor VC Hz rpm kw Pa C kg WGZ50 MG 00-L 0 ~ /60 65,0 6, , p. 5 / L5) WGZ50 MG 00-Q 0 ~ /60 690,70 7, ,7 p. 5 / L5) subject to alterations () Nominal data in operating point with maximum load and 00 VC Curves n [rpm] P [kw] I [] Lw [d()] p sf Pa 0, 0, 0, 0, 0,5 0,6 0,7 0,8 in H O q V cfm m /h ir performance measured as per: ISO 580, Installation category, in ebm-papst full nozzle and without protection against accidental contact Suction-side noise levels: Lw as per ISO 7, Lp measured at m distance to fan axis The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! ,69,6,59,0,57,0,8,70,6 5, 5,97 6,70 5,9 6,67 7,0 7,

3 Technical features: See electrical connections EMC: Interference emission acc. to EN (household environment) Interference immunity acc. to EN (industrial environment) Leakage current: <,5 m Terminal box: Electrical connection via terminal strip Protection class: I Product conforming to standards: CE, EN pprovals: UL, CS Direction of air flow "V" "V" "V" With full round nozzle WG Z50-F0-0 WG Z50-FC0-0

4 EC axial fans Ø 50 with motor MG00, drawings for direction of air flow "V" with full round nozzle 09± Type Mass [kg] WG Z50-F0-0 WG Z50-FC0-0, Ø (6x) 6x Ø0 Ø Tightening torque:,5 Nm±0,5 Nm Ø "V" 0 8. ± M0x.5 (x) Cable diameter: min. mm, max. 0 mm Tightening torque:,0 Nm±0,6 Nm M5x.5 (x) Cable diameter: min. 9 mm, max. 6 mm Tightening torque: 6,0 Nm±0,9 Nm,7

5 Electrical connections EC L5) Technical features: PFC (passive) RS85 MODUS Integrated PID controller Motor current limitation, alarm relay Control input 0-0 VDC or -0 m Line undervoltage / phase failure detection Input for sensor 0-0 V or -0 m Electronics / motor overtemperature protection Slave output 0-0 V max. 5 m Locked-rotor protection, soft start Output 0 VDC (±5 % / -0 %) max. 50 m Digital inputs for day/night switch, Output 0 VDC (+ %) max. 0 m enabling, cooling / heating KL KL KL RS RS in U +0 V in I Din NO COM NC PE L L L Din Din in U +0 V in I out Connector Connection ssignment / function Connector Connection ssignment / function KL L Mains; L KL Din Digital input (enabling / disabling of electronics),, L L Mains; L Mains; L Enabling: Pin open or applied voltage VDC Disabling: ridge to or applied voltage < VDC PE PE Protective earth in I nalogue set value input, -0 m (impedance 00 Ω), KL NC larm relay, break for failure only to be used as alternative to terminal in U COM larm relay, COMMON (, 50 VC, C) +0 V Supply for external potentiometer, NO larm relay, make for failure inu 0 VDC (± %) max. 0 m nalogue set value input, 0-0 V (impedance 00 kω), only to be used as alternative to terminal in I RS RS85 interface for MODUS RTU; RS RS RS85 interface for MODUS RTU; RS out nalogue output 0-0 V max. 5 m, reading of current motor speed / current motor control factor in I nalog. actual value input, -0m (impedance 00Ω), +0 V only to be used as alternative to terminal in U Supply for external sensor, 0 VDC (+5 % / -0%) max. 50 m in U nalog. actual value input, 0-0 V (impedance 00 kω), only to be used as alternative to terminal in I Din Digital input (switch Normal / Inverse), The preset effective direction of the integrated controller can be selected via US or via digital input Normal/Inverse. Normal: Pin open or applied voltage VDC Inverse: ridge to or applied voltage < VDC Din Digital input (switch Day / Night), The preset set of parameters can be selected via US or via digital input Day/Night. Day: Pin open or applied voltage VDC Night: ridge to or applied voltage < VDC 5