FTDX3000 SERIES CAT OPERATION REFERENCE BOOK YAESU MUSEN CO., LTD.

Transcription

1 FTD3000 SERIES CAT PERATIN REFERENCE BK YAESU MUSEN C., LTD.

2 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver) System in the FTD3000 transceiver provides control of frequency, VF, memory, and other settings such as dual-channel memories and diversity reception using an external personal computer. This allows multiple control operations to be fully automated with single mouse clicks, or keystroke operations on the computer keyboard. Using the RS-232C Cable The FTD3000 transceiver has a built-in level converter, allowing direct connection from the rear-panel CAT jack to the serial port of your computer without the need of any external boxes. When using the RS-232C cable, set Menu item 037 CAT SELECT to RS232C. You will need a serial cable for connection to the RS- 232C (serial or CM port) connector on your computer. Purchase a standard serial cable (not the so-called null modem type), ensuring it has the correct gender and number of pins (some serial CM port connectors use a 9-pin rather than 25-pin configuration). If your computer uses a custom connector, you may have to construct the cable. In this case, refer to the technical documentation supplied with your computer for correct data connection. Using the USB Cable Note: A USB driver is required for remote control from a computer. Download the driver from the Yaesu website ( The FTD3000 transceiver has a built-in USB to Dual UART Bridge, allowing direct connection from the rearpanel USB jack to the USB jack of your computer without the need of any external boxes. When using the USB cable, set Menu item 037 CAT SELECT to USB. You will need a USB cable to connect to the USB jack on your computer. PIN N. FTD3000 PIN NAME N/A SERIAL UT SERIAL IN N/A GND N/A RTS CTS N/A CNNECTIN I/ utput Input Input utput RS-232C Straight Cable FUNCTIN utputs the Serial Data from the transceiver to the computer. Inputs the Serial Data from the computer to the transceiver. Signal Ground When the computer is not ready to receive data, this port goes to L to inhibit the transmit data from the transceiver. When the transceiver is not ready to receive data, this port goes to L to inhibit the transmit data from the computer. Personal Computer YAESU MUSEN does not produce CAT System operating software due to the wide variety of personal computers and operating systems in use today. However, the information provided in this chapter explains the serial data structure and opcodes used by the CAT system. This information, along with the short programming examples, is intended to help you start writing programs on your own. As you become more familiar with CAT operation, you can customize programs for your operating needs and utilize the full operating potential of this system. FTD3000 Personal Computer USB Cable 1 FTD3000 CAT peration Manual

3 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN A computer control command is composed of an alphabetical command, various parameters, and the terminator that signals the end of the control command. Example: Set the VF-A frequency to MHz. FA ; Command Parameter Terminator There are three commands for the FTD3000 as shown below: Set command: Set a particular condition (to the FTD3000) Read command: Reads an answer (from the FTD3000) Answer command: Transmits a condition (from the FTD3000) For example, note the following case of the FA command (Set the VF-A frequency): To set the VF-A frequency to MHz, the following command is sent from the computer to the transceiver: FA ; (Set command) To read the VF-A frequency, the following command is sent from the computer to the transceiver: FA; (Read command) When the Read command above has been sent, the following command is returned to the computer: FA ; (Answer command) Alphabetical Commands A command consists of 2 alphabetical characters. You may use either lower or upper case characters. The commands available for this transceiver are listed in the PC Control Command Tables on the following pages. CNTRL CMMAND Parameters Parameters are used to specify information necessary to implement the desired command. The parameters to be used for each command are predetermined. The number of digits assigned to each parameter is also predetermined. Refer to the Control Command List and the Control Command Tables to configure the appropriate parameters. When configuring parameters, be careful not to make the following mistakes. For example, when the correct parameter is IS (IF SHIFT): IS01000; Not enough parameters specified (No direction (+) given for the IF shift) IS0+100; Not enough digits (nly three frequency digits given) IS0_+_1000; Unnecessary characters between parameters IS ; Too many digits (Five frequency digits given) Note: If a particular parameter is not applicable to the FTD3000, the parameter digits should be filled using any character except the ASCII control codes (00 to 1Fh) and the terminator (;). Terminator To signal the end of a command, it is necessary to use a semicolon (;). The digit where this special character must appear differs depending on the command used. 2 FTD3000 CAT peration Manual

4 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN Function CMMAND SET READ ANS. AI Function CMMAND SET READ ANS. AI AB VF-A T VF-B PC PWER CNTRL AC ANTENNA TUNER CNTRL PL SPEECH PRCESSR LEVEL AG AF GAIN PR SPEECH PRCESSR AI AUT INFRMATIN PS PWER SWITCH AM VF-A T MEMRY CHANNEL QI QMB STRE AN ANTENNA NUMBER QR QMB RECALL BA VF-B T VF-A QS QUICK SPLIT BC AUT NTCH RA RF ATTENUATR BD BAND DWN RC CLAR CLEAR BI BREAK-IN RD CLAR DWN BP MANUAL NTCH RF RFING FILTER BS BAND SELECT RG RF GAIN BU BAND UP RI RADI INFRMATIN BY BUSY RL NISE REDUCTIN LEVEL CH CHANNEL UP/DWN RM READ METER CN CTCSS NUMBER R RTATR C CNTUR RS RADI STATUS CS CW SPT RT CLAR CT CTCSS RU CLAR UP DA DIMMER SC SCAN DN DWN SD SEMI BREAK-IN DELAY TIME ED ENCRDER DWN SF SUB-DIAL FUNCTIN EK ENT KEY SH WIDTH EU ENCRDER UP SM S METER EM ENCDE MEMRY SQ SQUELCH LEVEL EN ENCDE SV SWAP VF E MENU TS TW FA FREQUENCY VF-A T T SET FB FREQUENCY VF-B UL UNLCK FR FUNCTIN R UP UP FS FAST STEP VD V DELAY TIME FT FUNCTIN T VF utune FILTER GT AGC FUNCTIN VG V GAIN IF INFRMATIN VM [V/M] KEY FUNCTIN IS IF-SHIFT VS VF SELECT KM KEYER MEMRY V V KP KEY PITCH T T CLAR KR KEYER KS KEY SPEED KY CW KEYING LK LCK LM LAD MESSEGE MA MEMRY CHANNEL T VF-A MC MEMRY CHANNEL MD MDE MG MIC GAIN ML MNITR LEVEL MR MEMRY READ MS METER SW MW MEMRY WRITE M M SET NA NARRW NB NISE BLANKER NL NISE BLANKER LEVEL NR NISE REDUCTIN I PPSITE BAND NFRMATIN S FFSET (Repeater Shift) PA PRE-AMP (IP) PB PLAY BACK 3 FTD3000 CAT peration Manual

5 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN AB VF-A T VF-B A B ; AC ANTENNA TUNER CNTRL A C P1 P2 P3 ; A C ; A C P1 P2 P3 ; AG AF GAIN A G P1 P2 P2 P2 ; A G P1 ; A G P1 P2 P2 P2 ; P2 0: Fixed P P3 0: Tuner FF 1: Tuner N 2: Tuning Start AI AUT INFRMATIN A I P1 ; A I ; A I P1 ; P1 0: Auto Information FF 1: Auto Information N This parameter is set to 0 (FF) automatically when the transceiver is turned FF. AM VF-A T MEMRY CHANNEL A M ; AN ANTENNA NUMBER A N P1 P2 ; A N P1 ; A N P1 P3 P4 ; BA VF-B T VF-A B A ; P2 1: ANT 1 2: ANT 2 3: ANT 3 P3 1: ANT 1 2: ANT 2 3: ANT 3 P4 0: Fixed BC AUT NTCH B C P1 P2 ; B C P1 ; B C P1 P2 ; BD BAND DWN B D P1 ; P1 0:Fixed P2 0: Auto Notch FF 1: Auto Notch N 4 FTD3000 CAT peration Manual

6 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN BI BREAK-IN B I P1 ; B I ; B I P1 ; BP MANUAL NTCH B P P1 P2 P3 P3 P3 ; B P P1 P2 ; B P P1 P2 P3 P3 P3 ; BS BAND SELECT B S P1 P1 ; P1 0: Break-in FF 1: Break-in N P1 0:Fixed P2 0: Manual NTCH N/FF 1: Manual NTCH LEVEL P1 00: 1.8 MHz 06: 18 MHz 01: 3.5 MHz 07: 21 MHz 02: : 24.5 MHz 03: 7 MHz 09: 28 MHz 04: 10 MHz 10: 50 MHz 05: 14 MHz 11: GEN P3 P2=0 000: FF 001: N P2= (NTCH Frequency : x 10 Hz ) BU BAND UP B U P1 ; BY BUSY B Y ; B Y P1 P2 ; CH CHANNEL UP/DWN C H P1 ; P1 0: R BUSY FF 1: R BUSY N P2 0: Fixed P1 0: Memory Channel UP 1: Memory Channel DWN CN CTCSS TNE FREQUENCY C N P1 P2 P2 ; C N P1 ; C N P1 P2 P2 ; P2 0-49: Tone Frequency Number (See Table 1) C CNTUR C P1 P2 P3 P3 ; C P1 P2 ; C P1 P2 P3 P3 ; CS CW SPT C S P1 ; C S ; C S P1 ; P1 0:Fixed P2 0: CNTUR/APF N/FF 1: CNTUR FREQ 2: APF FREQ P1 0: FF 1: N 5 P3 P2=000: CNTUR/APF FF 01: CNTUR N 02: APF N P2= (CNTUR Frequency Hz) P2= (APF Frequency Hz) FTD3000 CAT peration Manual

7 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CT CTCSS C T P1 P2 ; C T P1 ; C T P1 P2 ; P2 0: CTCSS FF 1: CTCSS ENC/DEC N 2: CTCSS ENC N TABLE Hz 69.3 Hz 71.9 Hz 74.4 Hz 77.0 Hz 79.7 Hz 82.5 Hz 85.4 Hz 88.5 Hz Hz 94.8 Hz 97.4 Hz Hz Hz Hz Hz Hz Hz TABLE 1 (CTCSS TNE CHART) Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz DA DIMMER D A P1 P1 P2 P2 P3 P3 ; D A ; D A P1 P1 P2 P2 P3 P3 ; P : VF-A Display Brightness Level P : Keypad Brightness Level P : TFT Display Brightness Level DN MIC DWN D N ; ED ENCRDER DWN E D P1 P2 P2 ; P1 0: MAIN ENCRDER 1: SUB ENCRDER 4: MIC/SPEED ENCRDER 5: PRC/CAR ENCRDER 6: NTCH ENCRDER 7: CNT ENCRDER P : Steps EK ENT KEY E K ; EU ENCRDER UP E U P1 P2 P2 ; P1 0: MAIN ENCRDER 1: SUB ENCRDER 4: MIC ENCRDER 5: PRC ENCRDER 6: NTCH ENCRDER 7: CNT ENCRDER P : Steps E MENU Set nn ** E P1 P1 P1 P2 P2 ~ P2 ; E P1 P1 P1 ; Answer nn ** E P1 P1 P1 P2 P2 ~ P2 ; P1 : (MENU Number) P2 : Parameter (See Table 2 and Table 4) 6 FTD3000 CAT peration Manual

8 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN EM ENCDE MEMRY Set ~ E N P1 P2 P3 P3 P3 ~ P3 ; E M P1 P2 ; Answer ~ E M P1 P2 P3 P3 P3 ~ P3 ; P1 0: RTTY 1: PSK P2: 1-5 : Memory Channel P3: Message Characters (up to 50 characters) TABLE 2 P1 FUNCTIN P2 001 AGC FAST-DELAY 20 ~ 4000 msec (20 msec/step) 002 AGC MID DELAY 20 ~ 4000 msec (20 msec/step) 003 AGC SLW DELAY 20 ~ 4000 msec (20 msec/step) 004 AGC AGC SLPE 0: NRMAL 1: SLPE 005 DISPLAY MY CALL Max 12 characters 006 DISPLAY MY CALL TIME 0 ~ 5sec 007 DISPLAY DIMMER VF 0 ~ DISPLAY DIMMER BACKLIGHT 0 ~ DISPLAY DIMMER TFT 0 ~ DISPLAY BAR DISPLAY SELECT 0: CLAR 1: CW TUNE 2: utune 011 DISPLAY METER TYPE SELECT 0: ANALG 1: BAR 012 DISPLAY BAR MTR PEAK HLD 0: FF 1: 0.5 sec 2: 1.0 sec 3: 2.0 sec 013 DISPLAY RTATR START UP 0: 0 1: 90 2: 180 3: DISPLAY RTATR FFSET ADJ -30 ~ 0 (P2=30 ~ 00, 2 step) 015 DVS R UT LEVEL 0 ~ DVS T UT LEVEL 0 ~ KEYER F KEYER TYPE 0: FF 1: BUG 2: ELEKEY 3: ACS 018 KEYER F CW KEYER 0: NRNAL 1: REVERSE 019 KEYER R KEYER TYPE 0: FF 1: BUG 2: ELEKEY 3: ACS 020 KEYER F CW KEYER 0: NRNAL 1: REVERSE 021 KEYER ELEKEY TYPE 0: ELEKEY-A 1: ELEKEY-B 022 KEYER CW WEIGHT 25 (1:2.5) ~ 45 (1:4.5) 023 KEYER BEACN TIME FF/1 ~ 690sec (0: FF) 024 KEYER NUMBER STYLE 0: : AUN 2: AUNT 3: A2N 4: A2NT 5: 12N 6: 12NT 025 KEYER CNTEST NUMBER 0000 ~ KEYER CW MEMRY 1 0: TET 1: MESSAGE 027 KEYER CW MEMRY 2 0: TET 1: MESSAGE 028 KEYER CW MEMRY 3 0: TET 1: MESSAGE 029 KEYER CW MEMRY 4 0: TET 1: MESSAGE 030 KEYER CW MEMRY 5 0: TET 1: MESSAGE 031 GENERAL ANT SELECT 0: BAND 1: STACK 032 GENERAL ANT3 SETTING 0: TR 1: R3/1 2: R3/2 033 GENERAL NB LEVEL 000 ~ GENERAL BEEP LEVEL 000 ~ GENERAL MNITR LEVEL 000 ~ GENERAL RF/SQL VR 0: RF 1: SQL 037 GENERAL CAT SELECT 0: RS232C 1: USB 038 GENERAL CAT RATE 0: 4800 bps 1: 9600 bps 2: bps 3: bps 039 GENERAL CAT TIME UT TIMER 0: 10 msec 1: 100 msec 2: 1000 msec 3: 3000 msec 040 GENERAL CAT RTS 0: DISABLE 1: ENABLE 041 GENERAL MEM GRUP 0: DISABLE 1: ENABLE 042 GENERAL QUICK SPLIT FREQ 20 ~ +00 (or 00) ~ +20 khz 043 GENERAL T TIME UT TIMER 00 (FF) ~ 30 min 044 GENERAL μtune DIAL STEP 0: DIAL STEP-2 1: DIAL STEP GENERAL MIC SCAN 0: DISABLE 1: ENABLE 046 GENERAL SCAN RESUME 0 PAUSE 1: TIME 047 GENERAL FREQ ADJ 25 ~ +00 (or 00) ~ MDE-AM AM LCUT FREQ 00: FF 1: 100Hz ~ 19: 1000Hz (50Hz steps) 049 MDE-AM AM LCUT SLPE 0: 6dB/oct 1: 18dB/oct 050 MDE-AM AM HCUT FREQ 00: FF 01: 700Hz ~ 67: 4000Hz (50Hz steps) 051 MDE-AM AM HCUT SLPE 0: 6dB/oct 1: 18dB/oct 052 MDE-AM AM MIC GAIN MCVR/FI(0 ~ 100) (P2 = 1000: MCVR, 0000 ~ 0100: FI(0 ~ 100)) 053 MDE-AM AM MIC SEL 0: FRNT 1: DATA 2: USB 054 MDE-CW CW PITCH 00: : 350 ~ 14: : 1050Hz (50Hz steps) 055 MDE-CW CW LCUT FREQ 00: FF 1: 100Hz ~ 19: 1000Hz (50Hz steps) 056 MDE-CW CW LCUT SLPE 0: 6dB/oct 1: 18dB/oct 057 MDE-CW CW HCUT FREQ 00: FF 01: 700Hz ~ 67: 4000Hz (50Hz steps) 058 MDE-CW CW HCUT SLPE 0: 6dB/oct 1: 18dB/oct 059 MDE-CW CW AUT MDE 0: FF 1: 50 MHz 2: N 060 MDE-CW CW BF 0: USB 1: LSB 2: AUT 061 MDE-CW CW BK-IN 0: SEMI BREAK-IN 1: FULL BREAK-IN 062 MDE-CW CW BK-IN DELAY 30 ~ 3000 msec (10 msec/step) 063 MDE-CW CW WAVE SHAPE 0: 1 1: 2 2: 4 3: 6 msec 064 MDE-CW CW FREQ DISPLAY 0: DIRECT FREQ 1: PITCH FFSET 065 MDE-CW PC KEYING 0: FF 1: N 2: RTS 066 MDE-CW QSK 0: 15 msec 1: 20 msec 2: 25 mesc 3: 30 msec 067 MDE-DATA DATA MDE 0: PSK 1: THER 068 MDE-DATA DATA TNE 0: : : 2000Hz 069 MDE-DATA THER DISP (SSB) ~ 0 ~ +3000Hz (10Hz steps) (P2 = ~ x0000 ~ +3000) 070 MDE-DATA THER SHIFT (SSB) ~ 0 ~ +3000Hz (10Hz steps) (P2 = ~ x0000 ~ +3000) 071 MDE-DATA DATA LCUT FREQ 00: FF 1: 100Hz ~ 19: 1000Hz (50Hz steps) 072 MDE-DATA DATA LCUT SLPE 0: 6dB/oct 1: 18dB/oct 073 MDE-DATA DATA HCUT FREQ 00: FF 01: 700Hz ~ 67: 4000Hz (50Hz steps) 074 MDE-DATA DATA HCUT SLPE 0: 6dB/oct 1: 18dB/oct 075 MDE-DATA DATA IN SELECT 0: DATA 1: USB 076 MDE-DATA DATA MIC GAIN MCVR/FI(0 ~ 100) (P2 = 1000: MCVR, 0000 ~ 0100: FI(0 ~ 100)) 077 MDE-DATA DATA UT LEVEL 0 ~ MDE-DATA DATA V GAIN 000 ~ MDE-DATA DATA V DELEY 30 ~ 300 ~ 3000 msec (10 msec/step) 7 FTD3000 CAT peration Manual

9 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN TABLE 3 P1 FUNCTIN P2 080 MDE-FM FM LCUT FREQ 00: FF 1: 100Hz ~ 19: 1000Hz (50Hz steps) 081 MDE-FM FM LCUT SLPE 0: 6dB/oct 1: 18dB/oct 082 MDE-FM FM HCUT FREQ 00: FF 01: 700Hz ~ 67: 4000Hz (50Hz steps) 083 MDE-FM FM HCUT SLPE 0: 6dB/oct 1: 18dB/oct 084 MDE-FM FM MIC GAIN MCVR/FI(0 ~ 100) (P2 = 1000: MCVR, 0000 ~ 0100: FI(0 ~ 100)) 085 MDE-FM FM MIC SEL 0: FRNT 1: DATA 2: USB 086 MDE-FM RPT SHIFT(28MHz) 0 ~ 100 ~ 1000 khz (10 khz/step) 087 MDE-FM RPT SHIFT(50MHz) 0 ~ 100 ~ 1000 ~ 4000 khz (10 khz/step) 088 MDE-FM TNE FREQ 67.0 ~ 254 Hz 089 MDE-RTY RTTY LCUT FREQ 00: FF 1: 100Hz ~ 19: 1000Hz (50Hz steps) 090 MDE-RTY RTTY LCUT SLPE 0: 6dB/oct 1: 18dB/oct 091 MDE-RTY RTTY HCUT FREQ 00: FF 01: 700Hz ~ 67: 4000Hz (50Hz steps) 092 MDE-RTY RTTY HCUT SLPE 0: 6dB/oct 1: 18dB/oct 093 MDE-RTY RTTY SHIFT PRT 0: REAR 1: USB 094 MDE-RTY RTTY PLARITY-R 0: NR 1: REV 095 MDE-RTY RTTY PLARITY-T 0: NR 1: REV 096 MDE-RTY RTTY UT LEVEL 0 ~ MDE-RTY RTTY SHIFT 1: 170 Hz 1: 200 Hz 2: 425 Hz 3: 850 Hz 098 MDE-RTY RTTY MARK FREQ 1: 1275 Hz 2: 2125 Hz 099 MDE-SSB SSB LCUT FREQ 00: FF 1: 100Hz ~ 19: 1000Hz (50Hz steps) 100 MDE-SSB SSB LCUT SLPE 0: 6dB/oct 1: 18dB/oct 101 MDE-SSB SSB HCUT FREQ 00: FF 01: 700Hz ~ 67: 4000Hz (50Hz steps) 102 MDE-SSB SSB HCUT SLPE 0: 6dB/oct 1: 18dB/oct 103 MDE-SSB SSB MIC SEL 0: FRNT 1: DATA 2: USB 104 MDE-SSB SSB T BPF 0: 50 ~ : 100 ~ : 200 ~ : 300 ~ : 400 ~ 2600 (Hz) 5: 3000WB 105 MDE-SSB LSB R CARRIER -200Hz ~ 0 ~ +200Hz (10Hz steps) (P2= -200 ~ x000 ~ +200) 106 MDE-SSB USB R CARRIER -200Hz ~ 0 ~ +200Hz (10Hz steps) (P2= -200 ~ x000 ~ +200) 107 R DSP APF WIDTH 0: NARRW 1: MEDIUM 2: WIDE 108 R DSP CNTUR LEVEL 40 ~ 0 ~ +20 (P2= 40 ~ x00 ~ +20) 109 R DSP CNTUR WIDTH 01 ~ R DSP DNR LEVEL 1 ~ R DSP IF NTCH WIDTH 0: NARRW 1: WIDE 112 R DSP HF CW SHAPE 0: SFT 1: SHARP 113 R DSP HF CW SLPE 0: STEEP 1: MEDIUM 2: GENTLE 114 R DSP 6M CW SHAPE 0: SFT 1: SHARP 115 R DSP 6M CW SLPE 0: STEEP 1: MEDIUM 2: GENTLE 116 R DSP HF PSK SHAPE 0: SFT 1: SHARP 117 R DSP HF PSK SLPE 0: STEEP 1: MEDIUM 2: GENTLE 118 R DSP HF FSK SHAPE 0: SFT 1: SHARP 119 R DSP HF FSK SLPE 0: STEEP 1: MEDIUM 2: GENTLE 120 R DSP HF SSB SHAPE 0: SFT 1: SHARP 121 R DSP HF SSB SLPE 0: STEEP 1: MEDIUM 2: GENTLE 122 R DSP 6M SSB SHAPE 0: SFT 1: SHARP 123 R DSP 6M SSB SLPE 0: STEEP 1: MEDIUM 2: GENTLE 124 SCPE SCPE MDE 0: CENTER 1: FI 125 SCPE SCPE SPEED 0: FAST 1: SLW 126 SCPE SCPE AUT TIME 0: FF 1: 3 2: 5 3: 10 (sec) 127 SCPE START DIAL SPEED 0: 0.5k 1: 1k 2: 2k 3: 4k 4: 8k 5: 16k 128 SCPE SPAN FREQ 0: 20k 1: 50k 2: 100k 3: 200k 4: 500k 5: 1000k 129 SCPE FI 1.8MHz 1.800MHz ~ 1.999MHz (1kHz steps) 130 SCPE FI 1.8MHz SPAN 2: 20k 3: 50k 4: 100k 5: 200k 6: 500k 7: 1000kHz 131 SCPE FI 3.5MHz 3.500MHz ~ 3.999MHz (1kHz steps) 132 SCPE FI 3.5MHzSPAN 2: 20k 3: 50k 4: 100k 5: 200k 6: 500k 7: 1000kHz 133 SCPE FI 5.0MHz 5.250MHz ~ 5.499MHz (1kHz steps) 134 SCPE FI 5.0MHz SPAN 2: 20k 3: 50k 4: 100k 5: 200k 6: 500k 7: 1000kHz 135 SCPE FI 7.0MHz 7.000MHz ~ 7.299MHz (1kHz steps) 136 SCPE FI 7.0MHz SPAN 2: 20k 3: 50k 4: 100k 5: 200k 6: 500k 7: 1000kHz 137 SCPE FI 10MHz MHz ~ MHz (1kHz steps) 138 SCPE FI 10MHz SPAN 2: 20k 3: 50k 4: 100k 5: 200k 6: 500k 7: 1000kHz 139 SCPE FI 14MHz MHz ~ Hz (1kHz steps) 140 SCPE FI 14MHz SPAN 2: 20k 3: 50k 4: 100k 5: 200k 6: 500k 7: 1000kHz 141 SCPE FI 18MHz MHz ~ MHz (1kHz steps) 142 SCPE FI 18MHzSPAN 2: 20k 3: 50k 4: 100k 5: 200k 6: 500k 7: 1000kHz 143 SCPE FI 21MHz MHz ~ MHz (1kHz steps) 144 SCPE FI 21MHz SPAN 2: 20k 3: 50k 4: 100k 5: 200k 6: 500k 7: 1000kHz 145 SCPE FI 24MHz MHz ~ MHz (1kHz steps) 146 SCPE FI 24MHz SPAN 2: 20k 3: 50k 4: 100k 5: 200k 6: 500k 7: 1000kHz 147 SCPE FI 28MHz MHz ~ MHz (1kHz steps) 148 SCPE FI 28MHz SPAN 2: 20k 3: 50k 4: 100k 5: 200k 6: 500k 7: 1000kHz 149 SCPE FI 50MHz MHz ~ MHz (1kHz steps) 150 SCPE FI 50MHzSPAN 2: 20k 3: 50k 4: 100k 5: 200k 6: 500k 7: 1000kHz 151 TUNING CW DIAL STEP 0: 1 1: 5Hz 2: 10Hz 152 TUNING DATA DIAL STEP 0: 1 1: 5Hz 2: 10Hz 153 TUNING AM/FM DIAL STEP 0: 10 1: 100Hz 154 TUNING RTTY DIAL STEP 0: 1 1: 5Hz 2: 10Hz 155 TUNING SSB DIAL STEP 0: 1 1: 5Hz 2: 10Hz 156 TUNING AM CH STEP 0: 2.5 1: 5 2: 9 3: 10 4: 12.5kHz 157 TUNING FM CH STEP 0: 2.5 1: : 10 3: : 20 5: 25kHz 158 TUNING 1MHz/100kHz SELECT 0: 1MHz 1: 100kHz 159 T AUDI PRMTRC EQ1 FREQ 1: 100 2: 200 3: 300 4: 400 5: 500 6: 600 7: T AUDI PRMTRC EQ1 LEVEL -10 ~ 0 ~ +10 (P2 = -10 ~ x00 ~ +10) 161 T AUDI PRMTRC EQ1 BWTH 1 ~ T AUDI PRMTRC EQ2 FREQ 1: 700 2: 800 3: 900 4: : : : : : T AUDI PRMTRC EQ2 LEVEL -10 ~ 0 ~ +10 (P2 = -10 ~ x00 ~ +10) 164 T AUDI PRMTRC EQ2 BWTH 1 ~ T AUDI PRMTRC EQ3 FREQ 1: : : : : : : T AUDI PRMTRC EQ3 LEVEL -10 ~ 0 ~ +10 (P2 = -10 ~ x00 ~ +10) 167 T AUDI PRMTRC EQ3 BWTH 1 ~ T AUDI P-PRMTRC EQ1 FREQ 1: 100 2: 200 3: 300 4: 400 5: 500 6: 600 7: T AUDI P-PRMTRC EQ1 LEVEL -10 ~ 0 ~ +10 (P2 = -10 ~ x00 ~ +10) 170 T AUDI P-PRMTRC EQ1 BWTH 1 ~ 10 8 FTD3000 CAT peration Manual

10 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN TABLE 4 P1 FUNCTIN P2 171 T AUDI P-PRMTRC EQ2 FREQ 1: 700 2: 800 3: 900 4: : : : : : T AUDI P-PRMTRC EQ2 LEVEL -10 ~ 0 ~ +10 (P2 = -10 ~ x00 ~ +10) 173 T AUDI P-PRMTRC EQ2 BWTH 1 ~ T AUDI P-PRMTRC EQ3 FREQ 1: : : : : : : T AUDI P-PRMTRC EQ3 LEVEL -10 ~ 0 ~ +10 (P2 = -10 ~ x00 ~ +10) 176 T AUDI P-PRMTRC EQ3 BWTH 1 ~ T GNRL T MA PWER 5 ~ T GNRL ET AMP TUNING PWR 0: 10 1: 20 2: 50 3: T GNRL TUNER SELECT 0: INTERNAL 1: ETERNAL 180 T GNRL V SELECT 0: MIC 1: DATA 181 T GNRL V GAIN 0 ~ T GNRL V DELAY 30 ~ 300 ~ 3000 msec (10 msec/step) 183 T GNRL ANTI V GAIN 0 ~ T GNRL EMERGENCY FREQ T 0: DISABLE 1: ENABLE 185 AF SCPE FFT DISPLAY MDE 0: SPECTRUM 1: WATER FALL 186 AF SCPE FFT ATT 0: 0 1: 10 2: 20 db 187 DEC CW CW DECDE BW 0: 25 1: 50 2: 100 3: 250Hz 188 E/D RTTY R USS 0: DISABLE 1: ENABLE 189 E/D RTTY T USS 0: DISABLE 1: ENABLE 190 E/D RTTY R NEW LINE CDE 0: CR, LF, CR+L 1: CR+LF 191 E/D RTTY T AUT CR+LF 0: DISABLE 1: ENABLE 192 E/D RTTY T DIDDLE 0: FF 1: BLANK 2: LTRS 193 E/D RTTY BAUDT CDE 0: CCIT 1: US 194 E/D PSK PSK MDE 0: BPSK 1: QPSK 195 E/D PSK DECDE AFC RANGE 0: ±8 1: ±15 2: ± E/D PSK QPSK PLARITY REV 0: R-N, T-N 1: R-R, T-N 2: R-N, T-R 3: R-R, T-R EN ENCDE Set ~ E N P1 P2 ; Answer ~ FA FREQUENCY VF-A F A P1 P1 P1 P1 P1 P1 P1 P ; F A ; F A P1 P1 P1 P1 P1 P1 P1 P ; FB FREQUENCY VF-B F B P1 P1 P1 P1 P1 P1 P1 P P1 P1 P1 ; F B ; F B P1 P1 P1 P1 P1 P1 P1 P P1 P1 P1 ; P1 0: RTTY 1: PSK P2: 1: Message Memory 1 Playback 2: Message Memory 2 Playback 3: Message Memory 3 Playback 4: Message Memory 4 Playback 5: Message Memory 5 Playback P (Hz) P (Hz) FR FUNCTIN R F R P1 ; F R ; F R P1 ; P1 0: VF-A Band Receiver: R, VF-B Band Receiver: FF 1: VF-A Band Receiver: Mute, VF-B Band Receiver: FF 4: VF-A Band Receiver: FF, VF-B Band Receiver: R 5: VF-A Band Receiver: FF, VF-B Band Receiver: Mute FS FAST STEP F S P1 ; F S ; F S P1 ; P1 0: VF-A FAST Key FF 1: VF-A FAST Key N 2: VF-B FAST Key FF 3: VF-B FAST Key N 4: VF-A FAST Key FF, VF-B FAST Key FF 5: VF-A FAST Key N, VF-B FAST Key FF 6: VF-A FAST Key FF, VF-B FAST Key N 7: VF-A FAST Key N, VF-B FAST Key N 9 FTD3000 CAT peration Manual

11 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FT FUNCTIN T F T P1 ; F T ; F T P2 ; P1 0: VF-A Band: T/R (Toggle) 1: VF-B Band: T/R (Toggle) 2: VF-A Band Transmitter: T 3: VF-B Band Transmitter: T P2 0: VF-A Band Transmitter: T 1: VF-B Band Transmitter: T GT AGC FUNCTIN G T P1 P2 ; G T P1 ; G T P1 P3 ; P2 0: AGC FF 1: AGC FAST 2: AGC MID 3: AGC SLW 4: AGC AUT P3 0: AGC FF 1: AGC FAST 2: AGC MID 3: AGC SLW 4: AGC AUT-FAST 5: AGC AUT-MID 6: AGC AUT-SLW IF INFRMATIN I F ; I F P1 P1 P1 P2 P2 P2 P2 P P2 P2 P2 P3 P3 P3 P3 P3 P4 P P6 P7 P8 P9 P9 P10 ; P (Memory Channel) P2 VF-A Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift Clarifier ffset: (Hz) P4 0: R CLAR FF 1: R CLAR N P5 0: T CLAR FF 1: T CLAR N P6 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U P7 0: VF 1: Memory 2: Memory Tune 3: Quick Memory Bank (QMB) 4: QMB-MT P8 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC P9: 00 (Fixed) P10 0: Simplex 1: Plus Shift 2: Minus Shift IS IF-SHIFT I S P1 -/+ P2 P2 P2 P2 ; I S P1 ; I S P1 -/+ P2 P2 P2 P2 ; P1 0:Fixed P2: ~ Hz KM KEYER MEMRY Set ~ 53 ** K M P1 P2 P2 P2 P2 ~ P2 ; K M P1 ; Answer ~ 53 ** K M P1 P2 P2 P2 P2 ~ P2 ; P1 1-5 : Keyer Memory Channel Number P2: Message Characters (up to 50 characters) KP KEY PITCH K P P1 P1 ; K P ; K P P1 P1 ; KR KEYER K R P1 ; K R ; K R P1 ; KS KEY SPEED K S P1 P1 P1 ; K S ; K S P1 P1 P1 ; P1 00: 300 Hz - 75: 1050 Hz (10Hz steps) P1 0: KEYER FF 1: KEYER N P (WPM) 10 FTD3000 CAT peration Manual

12 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN KY CW KEYING K Y P1 ; P1 1: Keyer Memory 1 Playback 6: Message Keyer 1 Playback 2: Keyer Memory 2 Playback 7: Message Keyer 2 Playback 3: Keyer Memory 3 Playback 8: Message Keyer 3 Playback 4: Keyer Memory 4 Playback 9: Message Keyer 4 Playback 5: Keyer Memory 5 Playback A: Message Keyer 5 Playback LK LCK L K P1 ; L K ; L K P1 ; LM LAD MESSEGE L M P1 P2 ; L M P1 ; L M P1 P2 ; P1 0: VF-A DIAL Lock FF 1: VF-A DIAL Lock N 2: VF-B DIAL Lock FF 3: VF-B DIAL Lock N 4: VF-A DIAL Lock FF, VF-B DIAL Lock FF 5: VF-A DIAL Lock N, VF-B DIAL Lock FF 6: VF-A DIAL Lock FF, VF-B DIAL Lock N 7: VF-A DIAL Lock N, VF-B DIAL Lock N P1 0: DVS P2 P1=0 P1=1 1: P/B 0: DVS (Recording Stop) 0: P.B (Recording Stop) 1: DVS (CH 1 Recording Start/Stop) 1: P.B (Recording Start) 2: DVS (CH 2 Recording Start/Stop) 3: DVS (CH 3 Recording Start/Stop) 4: DVS (CH 4 Recording Start/Stop) 5: DVS (CH 5 Recording Start/Stop) MA MEMRY CHANNEL T VF-A M A ; MC MEMRY CHANNEL M C P1 P1 P1 ; M C ; M C P1 P1 P1 ; MD PERATING MDE M D P1 P2 ; M D P1 ; M D P1 P2 ; MG MIC GAIN M G P1 P1 P1 ; M G ; M G P1 P1 P1 ; ML MNITR LEVEL M L P1 P2 P2 P2 ; M L P1 ; M L P1 P2 P2 P2 ; P : Memory Channel Number : Regular Memory Channel 100: P-1L 101: P-1U ~ 116: P-9L 117: P-9U P2 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U D: AM-N P P1 0: MNI N/FF 1: MNI Level P2 P1=0 000: MNI FF 001: MNI N P1= FTD3000 CAT peration Manual

13 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN MR MEMRY CHANNEL READ M R P1 P1 P1 ; M R P1 P1 P1 P2 P2 P2 P2 P P2 P2 P2 P3 P3 P3 P3 P3 P4 P P6 P7 P8 P9 P9 P10 ; P1 Memory Channel Number( ) P2 Memory Channel Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift Clarifier ffset: (Hz) P4 0: R CLAR FF 1: R CLAR N P5 0: T CLAR FF 1: T CLAR N P6 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U P7 0: VF 1: Memory P8 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC P9: Tone Number (See Table 1) P10 0: Simplex 1: Plus Shift 2: Minus Shift MS METER SW M S P1 ; M S ; M S P1 ; P1 0: CMP 1: ALC 3: SWR 4: ID 5: VDD MW MEMRY CHANNEL WRITE M W P1 P1 P1 P2 P2 P2 P2 P P2 P2 P2 P3 P3 P3 P3 P3 P4 P P6 P7 P8 P9 P9 P10 ; P1 Memory Channel Number( ) P2 Memory Channel Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift Clarifier ffset: (Hz) P4 0: R CLAR FF 1: R CLAR N P5 0: T CLAR FF 1: T CLAR N P6 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U P7 0: (Fixed) P8 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC P9: 0: (Fixed) P10 0: Simplex 1: Plus Shift 2: Minus Shift M M SET M P1 ; N ; N P1 ; NA NARRW M A P1 P2 ; N A P1 ; N A P1 P2 ; NB NISE BLANKER STATUS N B P1 P2 ; N B P1 ; N B P1 P2 ; NL NISE BLANKER LEVEL N L P1 P2 P2 P2 ; N L P1 ; N L P1 P2 P2 P2 ; NR NISE REDUCTIN N R P1 P2 ; N R P1 ; N R P1 P2 ; P1 0: M FF 1: M N P1 Fixed P2 0: FF 1: N P1 Fixed P2 0: Noise Blanker FF 1: Noise Blanker N 2: Noise Blanker (Wide) N P1 Fixed P P1 Fixed P2 0: Noise Reduction FF 1: Noise Reduction N 12 FTD3000 CAT peration Manual

14 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN I PPSITE BAND INFRMATIN I ; I P1 P1 P1 P2 P2 P2 P2 P P2 P2 P2 P3 P3 P3 P3 P3 P4 P P6 P7 P8 P9 P9 P10 ; P1 Current Memory Channel( ) P2 VF-B Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift Clarifier ffset: (Hz) P4 0: R CLAR FF 1: R CLAR N P5 0: T CLAR FF 1: T CLAR N P6 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U P7 0: VF 1: Memory P8 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC P9: Tone Number (See Table 1) P10 0: Simplex 1: Plus Shift 2: Minus Shift S FFSET (REPEATER SHIFT) S P1 P2 ; S P1 ; S P1 P2 ; PA PRE-AMP (IP) P A P1 P2 ; P A P1 ; P A P1 P2 ; PB PLAY BACK P B P1 P2 ; P B P1 ; P B P1 P2 ; PC PWER CNTRL P C P1 P1 P1 ; P C ; P C P1 P1 P1 ; PL SPEECH PRCESSR LEVEL P L P1 P1 P1 ; P L ; P L P1 P1 P1 ; PR SPEECH PRCESSR P R P1 P2 ; P R P1 ; P R P1 P2 ; PS PWER SWITCH P S P1 ; P S ; P S P1 ; P1 Fixed P2 0: Simplex 1: Plus Shift 2: Minus Shift : This command can be activated only with an FM mode. P1 0:Fixed P2 0: IP 1: AMP 1 2: AMP 2 P1 0: DVS P2 P1=0 P1=1 1: P/B 0: DVS (Playback Stop) 0: P.B (Playback Stop) 1: DVS (CH 1 Playback Start/Stop) 1: P.B (Playback Start) 2: DVS (CH 2 Playback Start/Stop) 3: DVS (CH 3 Playback Start/Stop) 4: DVS (CH 4 Playback Start/Stop) 5: DVS (CH 5 Playback Start/Stop) P P P1 0: Speech Processor FF 1: Parametric Microphone Equalizer N P2 1: FF 2: N P1 0: PWER FF 1: PWER N This command requires dummy data be initially sent. Then after one second and before two seconds the command is sent. 13 FTD3000 CAT peration Manual

15 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN QI QMB STRE Q I ; QR QMB RECALL Q R ; QS QUICK SPLIT Q S ; RA RF ATTENUATR R A P1 P2 ; R A P1 ; R A P1 P2 ; P1 0:Fixed P2 0: FF 1: 6 db 2: 12 db 3: 18 db RC CLAR CLEAR R C ; RD CLAR DWN R D P1 P1 P1 P1 ; P (Hz) RF RFING FILTER R F P1 P2 ; R F P1 ; R F P1 P3 ; RG RF GAIN R G P1 P2 P2 P2 ; R G P1 ; R G P1 P2 P2 P2 ; RI RADI INFRMATIN R I P1 ; R I P1 P2 ; P1 0:Fixed P3 1: 15 khz 8: 300 Hz P2 0: AUT 2: 6 khz 9: AUT Hz 1: 15 khz 3: 3 khz A: AUT Hz 2: 6 khz 4: AUT - 15 khz 3: 3 khz 5: AUT - 6kHz 4: 600 Hz 6: AUT - 3 khz 5: 300 Hz 7: 600 Hz P P1 0: Hi-SWR 8: VF-B-R P2 0: FF 1: MIC-EQ 1: N 3: REC 4: PLAY 5: VF-A T 6: VF-B T 7: VF-A R 14 FTD3000 CAT peration Manual

16 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN RL NISE REDUCTIN LEVEL R L P1 P2 P2 ; R L P1 ; R L P1 P2 P2 ; RM R RTATR R P1 ; R ; R P1 P2 P2 P2 P3 P3 P3 ; RS READ METER R M P1 ; R M P1 P2 P2 P2 ; RADI STATUS R S ; R S P1 ; RT CLAR R T P1 ; R T ; R T P1 ; RU R CLARIFIER PLUS FFSET R U P1 P1 P1 P1 ; P1 0:Fixed P P1 0: Depends on the front panel METER 5: P 1: S 6: SWR 2: Depends on the front panel METER 7: ID CMP /ALC /SWR /ID/VDD 8: VDD 3: CMP 4: ALC P P1 0: FF 1: Counter Clockwise 2: Clockwise 3: SPEED 1 % DWN 4: SPEED 1 % UP P2 DIRECTIN (0-450) P3 SPEED (0-100 %) P1 0: NRMAL MDE 1: MENU MDE P1 0: R Clarifier FF 1: R Clarifier N P (Hz) SC SCAN S C P1 ; S C ; S C P1 ; SD CW BREAK-IN DELAY TIME S D P1 P1 P1 P1 ; S D ; S D P1 P1 P1 P1 ; SF SUB-DIAL FUNCTIN S F P1 ; S F ; S F P1 ; P1 0: Scan FF 1: Scan N (UP ward) 2: Scan N (DWN ward) P ms P1 1: MHz 2: GRP 3: MCH 4:DIAL-B 5: CLAR 6: MDE 7: utune 15 FTD3000 CAT peration Manual

17 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN SH WIDTH S H P1 P2 P2 ; S H P1 ; S H P1 P2 P2 ; P1 0:Fixed P2 00 (See Table 5) TABLE 5 CMMAND P SSB (Narrow) 1500 Hz 200 Hz 400 Hz 600 Hz 850 Hz 1100 Hz 1350 Hz 1500 Hz 1650 Hz 1800 Hz SSB (Wide) 2400 Hz 1800 Hz 1950 Hz 2100 Hz 2200 Hz 2300 Hz 2400 Hz 2500 Hz 2600 Hz 2700 Hz 2800 Hz 2900 Hz 3000 Hz 3200 Hz 3400 Hz 3600 Hz 3800 Hz 4000 Hz CW (Narrow) 500 Hz 50 Hz 100 Hz 150 Hz 200 Hz 250 Hz 300 Hz 350 Hz 400 Hz 450 Hz 500 Hz BANDWIDTH CW (Wide) 2400 Hz 500 Hz 800 Hz 1200 Hz 1400 Hz 1700 Hz 2000 Hz 2400 Hz RTTY/PSK (Narrow) 500 Hz 50 Hz 100 Hz 150 Hz 200 Hz 250 Hz 300 Hz 350 Hz 400 Hz 450 Hz 500 Hz RTTY/PSK (Wide) 2400 Hz 500 Hz 800 Hz 1200 Hz 1400 Hz 1700 Hz 2000 Hz 2400 Hz SM S-METER READING S M P1 ; S M P1 P2 P2 P2 ; SQ SQUELCLH LEVEL S Q P1 P2 P2 P2 ; S Q P1 ; S Q P1 P2 P2 P2 ; P P SV SWAP VF S V ; TS TW T S P1 ; T S ; T S P1 ; T T SET T P1 ; T ; T P1 ; P1 0: TW FF 1: TW N P1 0: RADI T FF CAT T FF 1: RADI T FF CAT T N 2: RADI T N CAT T FF (Answer) 16 FTD3000 CAT peration Manual

18 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN UL PLL UNLCK STATUS U L ; U L P1 ; P1 0: PLL Lock 1: PLL Unlock UP UP U P ; VD V DELAY TIME V D P1 P1 P1 P1 ; V D ; V D P1 P1 P1 P1 ; VF VRF FILTER V F P1 P2 P3 P4 ; V F P1; V F P1 P2 P5 P5 P5 P6 ; VG V GAIN V G P1 P1 P1 ; V G ; V G P1 P1 P1 ; P ms (10 ms multiples) P4 0-9 P2 0: FF P : N P6 1: μtune 2: Default set P3 +: Plus Shift -: Minus Shift P VM VF-A T MEMRY CHANNEL V M ; VS VF SELECT V S P1 ; V S ; V S P1 ; V V STATUS V P1 ; V ; V P1 ; T T CLAR T P1 ; T ; T P1 ; P1 0: VF-A 1: VF-B P1 0: V FF 1: V N P1 0: T CLAR FF 1: T CLAR N 17 FTD3000 CAT peration Manual

19 Copyright 2012 YAESU MUSEN C., LTD. All rights reserved No portion of this manual may be reproduced without the permission of YAESU MUSEN C., LTD. E H H 1 2 0