CAT (COMPUTER AIDED TRANSCEIVER) OPERATION FT-450D CAT OPERATION YAESU MUSEN CO., LTD. FT-450D CAT OPERATION REFERENCE BOOK
|
|
- Emery Garrett
- 5 years ago
- Views:
Transcription
1 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FT-450D CAT PERATIN REFERENCE BK YAESU MUSEN C., LTD. FT-450D CAT PERATIN REFERENCE BK
2 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver) System in the FT-450D provides control of frequency, VF, memory, and other settings such as dual-channel memories and diversity reception using an external personal computer. This allows multiple control operations to be fully automated as single mouse clicks or keystroke operations on the computer keyboard. The FT-450D has a built-in level converter, allowing direct connection from the rear-panel CAT jack to the serial port of your computer without the need of any external boxes. You will need a serial cable for connection to the RS-232C (serial or CM port) connector on your computer. Purchase a standard serial cable (not the so-called null modem type), ensuring it has the correct gender and number of pins (some serial CM port connectors use a 9-pin rather than 25-pin configuration). If your computer uses a custom connector, you may have to construct the cable. In this case, refer to the technical documentation supplied with your computer for correct data connection. YAESU does not produce CAT System operating software due to the wide variety of personal computers and operating systems in use today. However, the information provided in this chapter explains the serial data structure and opcodes used by the CAT system. This information, along with the short programming examples, is intended to help you start writing programs on your own. As you become more familiar with CAT operation, you can customize programs later on for your operating needs and discover the true operating potential of this system. PIN N. PIN NAME N/A SERIAL UT SERIAL IN N/A GND N/A RTS CTS N/A CAT JACK I/ utput Input Input utput FUNCTIN utputs the Serial Data from the transceiver to the computer. Inputs the Serial Data from the computer to the transceiver. Signal Ground When the computer is not ready to receive data, this port goes to L for inhibit the transmit data from the transceiver. When the transceiver is not ready to receive data, this port goes to L for inhibit the transmit data from the computer. CM INPUT DC 13.8V 22A ANT DATA TUNER LINEAR CAT ET SPKR GND CAT RS-232C Straight Cable Page 1 FT-450D CAT PERATIN REFERENCE BK
3 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN A computer control command is composed of an alphabetical command, various parameters, and the terminator that signals the end of the control command. Example: Set the VF-A frequency to MHz. FA ; Command Parameter Terminator There is three for the FT-450D Command as shown below: Set command: Set a particular condition (to the FT-450D) Read command: Reads an answer (from the FT-450D) Answer command: Transmits a condition (from the FT-450D) For example, note the following in the case of the FA command (Set the VF-A frequency): To set the VF-A frequency to MHz, the following command is sent from the computer to the transceiver: FA ; (Set command) To read the VF-A frequency, the following command is sent from the computer to the transceiver: FA; (Read command) When the Read command above has been sent, the following command is returned to the computer: FA ; (Answer command) Alphabetical Commands A command consists of 2 alphabetical characters. You may use either lower or upper case characters. The commands available for this transceiver are listed in the PC Control Command Tables on the following pages. CNTRL CMMAND Parameters Parameters are used to specify information necessary to implement the desired command. The parameters to be used for each command are predetermined. The number of digits assigned to each parameter is also predetermined. Refer to the Control Command List and the Control Command Tables to configure the appropriate parameters. When configuring parameters, be careful not to make the following mistakes. For example, when correct parameter is IS (IF SHIFT): IS01000; Not enough parameters specified (No direction (+) given for the IF shift) IS0+100; Not enough digits (nly three frequency digits given) IS0_+_1000; Unnecessary characters between parameters IS ; Too many digits (Five frequency digits given) Note: If a particular parameter is not applicable to the FT- 450D, the parameter digits should be filled using any character except the ASCII control codes (00 to 1Fh) and the terminator (;). Terminator To signal the end of a command, it is necessary to use a semicolon (;). The digit where this special character must appear differs depending on the command used. FT-450D CAT PERATIN REFERENCE BK Page 2
4 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND LIST CMMAND FUNCTIN SET READ ANS. AI AC AG AI BD BI BP BS BU BY CH CN C CS CT DA DN DS ED EU E FA FB FS FT GT ID IF IS KM KP KR KS KY LK LM MC MD MG MK ML MR MS ANTENNA TUNER CNTRL AF GAIN AUT INFRMATIN BAND DWN BREAK-IN MANUAL NTCH BAND SELECT BAND UP BUSY CHANNEL UP/DWN CTCSS NUMBER CNTUR CW SPT CTCSS DIMMER MIC DWN DIMMER SWITCH ENCDER DWN ENCDER UP MENU FREQUENCY VF-A FREQUENCY VF-B FAST STEP FUNCTIN T AGC FUNCTIN IDENTIFICATIN INFRMATIN IF-SHIFT KEYER MEMRY KEY PITCH KEYER KEY SPEED CW KEYING LCK LAD MESSEGE MEMRY CHANNEL MDE MIC GAIN MDE KEY MNITR LEVEL MEMRY READ METER SW CMMAND FUNCTIN SET READ ANS. AI MW NA NB NR I S PA PB PC PS QI QR QS RA RC RD RG RI RL RM RP RS RT RU SC SD SH SM SQ ST SV TS T UL UP VD VG VM VR VS VV V MEMRY WRITE NARRW NISE BLANKER NISE REDUCTIN PPSITE BAND INFRMATIN FFSET (REPEATER SHIFT) PRE-AMP (IP) PLAY BACK PWER CNTRL PWER SWITH QMB STRE QMB RECALL QUICK SPLIT RF ATTENUATR CLAR CLEAR CLAR DWN RF GAIN RADI INFRMATIN NISE REDUCTIN LEVEL READ METER RESET PWER N RADI STATUS CLAR CLAR UP SCAN SEMI BREAK-IN DELAY TIME WIDTH S METER SQUELCH LEVEL STEP SWAP VF TW T SET UNLCK MIC UP V DELAY TIME V GAIN [V/M] KEY FUNCTIN VICE VF SELECT VF T VF V Page 3 FT-450D CAT PERATIN REFERENCE BK
5 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES AC ANTENNA TUNER CNTRL A C P3 ; A C ; A C P3 ; AG AF GAIN A G ; A G ; A G ; AI AUT INFRMATIN A I ; A I ; A I ; BD BAND DWN B D ; 0: Fixed P3 0: Tuner FF 0: Fixed 1: Tuner N 2: Tuning Start 0: Fixed : Auto Information FF 1: Auto Information N This parameter is set to 0 (FF) automatically when the transceiver is turned FF. 0: VF-A 1: VF-B BI BREAK-IN B I ; B I ; B I ; BP MANUAL NTCH B P P3 P3 P3 ; B P ; B P P3 P3 P3 ; BS BAND SELECT B S ; 0: Break-in FF 1: Break-in N 0: Fixed 0: Manual NTCH N/FF 1: Manual NTCH Position 00: 1.8 MHz 06: 18 MHz 01: 3.5 MHz 07: 21 MHz 02: Invalid 08: 24.5 MHz 03: 7 MHz 09: 28 MHz 04: 10 MHz 10: 50 MHz 05: 14 MHz 11: GEN P3 When =0 000: FF 001: N When = : NTCH position move to left 200: NTCH position move to center : NTCH position move to right BU BAND UP B U ; 0: Fixed BY BUSY B Y ; B Y ; 0: BUSY FF 1: BUSY N 0: Fixed FT-450D CAT PERATIN REFERENCE BK Page 4
6 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES CH CHANNEL UP/DWN C H ; 0: Memory Channel UP 1: Memory Channel DWN CN CTCSS TNE FREQUENCY C N ; C N ; C N ; 0: Fixed 00-49: Tone Frequency Number (See Table 1) C CNTUR C P3 P3 ; C ; C P3 P3 ; 0: Fixed 0: CNTUR N/FF 1: CNTUR Frequency P3 When =0, -2: CNTUR N -12 db -1: CNTUR N -6 db 00: CNTUR FF 01: CNTUR N +6 db 02: CNTUR N +12 db When =1, 01 ~ 07: 250 Hz 08 ~ 13: 500 Hz 14 ~ 19: 1 khz 20 ~ 25: 2 khz 26 ~ 32: 4 khz CS CW SPT C S ; C S ; C S ; 0: FF 1: N CT CTCSS C T ; C T ; C T ; DA DIMMER D A ; D A ; D A ; 0: Fixed 0: CTCSS FF 1: CTCSS ENC/DEC N 2: CTCSS ENC N : Fixed DN MIC DWN D N ; DS DIMMER SWITCH D S ; D S ; D S ; 0: DIMMER FF 1: DIMMER N TABLE Hz 69.3 Hz 71.9 Hz 74.4 Hz 77.0 Hz 79.7 Hz 82.5 Hz 85.4 Hz 88.5 Hz Hz 94.8 Hz 97.4 Hz Hz Hz Hz Hz Hz Hz CTCSS TNE CHART Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Page 5 FT-450D CAT PERATIN REFERENCE BK
7 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES ED ENCDER DWN E D ; 0:Fixed 01-99: Steps EU ENCDER UP E U ; 0:Fixed 01-99: Steps FT-450D CAT PERATIN REFERENCE BK Page 6
8 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES E MENU Set nn ** E ~ ; E ; Answer nn ** E ~ ; (MENU Number) Parameter (See Table 2) TABLE FUNCTIN ET MNU AM & FMDIAL AP TIME BEACN TIME BEACN TET BEEP TNE BEEPVL CAT RTS CAT TIME UT TIME CATRATE CLAR DIAL / SEL CLCK SHIFT DISP CNTRAST CW AUT MDE CW BF CW DELAY CW KEY REVERSE CW QSK CW PADDLE CWPITCH CWSPEED CW SIDE TNE CW TRAINING CW WEIGHT DATA DISP DATA MDE Not Used Not Used DIAL STEP DIG V EMERGENCY KEY HLD TIME LCK MDE M-TUNE MEMRY GRUP MEMRY TAG MIC EQ MIC GAIN MIC AUT SCAN MY BAND MY MDE MIC-DWN PG MIC-FAST PG MIC-UP PG METER PEAK HLD PANEL S CUSTM SWITCH QUICK SPLIT FREQ RF PWER SET REPEATER SHIFT DIRECTIN REPEATER SHIFT FFSET RTTY SHIFT RTTY TNE RTTY R PLARITY RTTY T PLARITY SCAN RESUME SEL DIAL MDE SQL TYPE SQL/RF GAIN STBY BEEP TNE FREQ TT TIME TUNER/ATAS V DELAY VGAIN 0: FF 1: N 0: DISABLE 1: ENABLE 00 (FF) ~ 01 (hour) ~ 12 (hour) 000 (FF) ~ 001 (sec) ~ 255 (sec) : 440 Hz 1: 880 Hz 2: 1760 Hz 000 (FI 0) ~ 100 (FI100) or 101 (LNK-50) ~ 151 (LNK0) ~ 201 (LNK+50) 0: DISABLE 1: ENABLE 0: 10 msec 1: 100 msec 2: 1000 msec 3: 3000 msec 1: 4800 bps 2: 9600 bps 3: bps 4: bps 5: DATA 0: DIAL 1: SEL 0: FF 1: N 01 ~ 24 0: FF 1: N 0: USB 1: LSB 2: AUT 0000 (FULL) / 0030 (msec) ~ 3000 (msec) 0: NRMAL 1: REVERSE 0: 15 msec 1: 20 msec 2: 25 msec 3: 30 msec 0: KEY 1: MIC 00-02: 400 Hz 03-04: 500 Hz 05-06: 600 Hz 07-08: 700 Hz 09-15: 800 Hz 04 (wpm) ~ 60 (wpm) 000 (FI 0) ~ 100 (FI100) or 101 (LNK-50) ~ 151 (LNK0) ~ 201 (LNK+50) 0: N (Numeric Character nly) 1: A (Alphabet Character nly) 2: M (Mixed: Numeric and Alphabet Character) 25 (1:2.5) ~ 45 (1:4.5) -300 (-3000 Hz) ~ +000 (0 Hz) ~ +300 (+3000 Hz) 0: RTTY 1: USER-L 2: USER-U 0: 1 Hz 1: 10 Hz 2: 20 Hz 3: 100 Hz 4: 200 Hz 000 (FF) ~ 100 0: FF 1: N 0: 0.5 sec 1: 1.0 sec 2: 1.5 sec 3: 2.0 sec 0: FREQ 1: PANEL 2: ALL 0: FF 1: N 0: FF 1: N 0: TAG-FF 1: TAG NAME 0 ~ 9 0: LW 1: NR 2: HIGH 0: FF 1: N See Table 3 See Table 4 See Table 5 See Table 5 See Table 5 0: FF 1: N See Table 5-20 (khz) ~ +00 (khz) ~ +20 (khz) 005 ~ 100 0: SIMPLE 1: +SHIFT 2: - SHIFT 000 (0 MHz) ~ 999 (99.9 MHz) 1: 170 Hz 2: 200 Hz 3: 425 Hz 4: 850 Hz 1: 1275 Hz 2: 2125 Hz 0: NRMAL 1: REVERSE 0: NRMAL 1: REVERSE 00: BUSY 01 (TIME: 1 sec) ~ 10 (TIME: 10 sec) 0: CW Sidetone Level 1: CW KEYER Speed 2: 100KHz Step 3: 1MHz Step 4: MIC GAIN Set 5: RF Power Set 0: FF 1: ENC 2: ENC DEC 0: SQL 1: RF GAIN 0: FF 1: N See Table 6 00 (FF) ~ 01 (minute) ~ 20 (minute) 0: ATAS 1: ET ATU 2: INT ATU 3: INTRATU 4: F TRANS 01 (100 msec) ~ 30 (300 msec) 001 ~ 255 Page 7 FT-450D CAT PERATIN REFERENCE BK
9 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES TABLE 3 TABLE FUNCTIN 1.8 MHz FF 3.5 MHz FF 7 MHz FF 10 MHz FF 14 MHz FF 18 MHz FF 21 MHz FF 24.5 MHz FF 28 MHz FF 50 MHz FF MY BAND FUNCTIN 1.8 MHz N 3.5 MHz N 7 MHz N 10 MHz N 14 MHz N 18 MHz N 21 MHz N 24.5 MHz N 28 MHz N 50 MHz N A0 B0 C0 MY BAND FUNCTIN LSB FF 11 USB FF 21 CW FF 31 FM FF 41 AM FF 51 DATA (RTTY-LSB) FF 61 CW-R FF 71 USER-L FF 81 DATA (RTTY-USB) FF 91 N.A. A1 FM-N FF B1 USER-U FF C1 FUNCTIN LSB N USB N CW N FM N AM N DATA (RTTY-LSB) N CW-R N USER-L N DATA (RTTY-USB) N N.A. FM-N N USER-U N TABLE 5 FUNCTIN 00 MNI Activates the Monitor function. 01 N/A No Function. 02 P/B Activates the Digital Voice Recorder. 03 PLAY1 Send the CW message, which is memorized in BEACN TET PLAY2 Send the CW message, which is memorized in BEACN TET PLAY3 Send the CW message, which is memorized in BEACN TET QSPL Activates Quick Split peration 07 SPT Generates a CW Spot Tone when using CW mode. 08 SQLFF pens the noise squelch. 09 SWR Transmits a 10 watts carrier (CW mode) to measure the SWR ratio. 10 TW Monitor the transmit frequency when Split Frequency operation is engaged. 11 VCC Display the DC supply voltage. 12 VICE2 Announces the current S-meter reading, operating frequency (with resolution to the displayed 100 Hz digit), and operating mode. 13 VM1MNI Play back the voice message, which is memorized in Voice Memory VM1REC Store the voice message into Voice Memory VM1T Send the voice message, which is memorized in Voice Memory VM2MNI Play back the voice message, which is memorized in Voice Memory VM2REC Store the voice message into Voice Memory VM2T Send the voice message, which is memorized in Voice Memory DWN Decreases the VF frequency by one step or moves the memory channel to the next-lowest channel. 20 FAST Set to the same function as the front panel s [FAST] button. 21 UP Increases the VF frequency by one step or moves the memory channel to the next-highest channel. 22 DSP Set to the same function as the front panel s [DSP] button. 23 IP/ATT Set to the same function as the front panel s [IP/ATT] button. 24 NB Set to the same function as the front panel s [NB] button. 25 AGC Set to the same function as the front panel s [AGC] button. 26 MDEDN Set to the same function as the front panel s [MDE ] button. 27 MDEUP Set to the same function as the front panel s [MDE ] button. 28 DSP/SEL Set to the same function as the front panel s [DSP/SEL] button. 29 KEYER Set to the same function as the front panel s [KEYER] button. 30 CLAR Set to the same function as the front panel s [CLAR] button. 31 BANDDN Set to the same function as the front panel s [BAND ] button. 32 BANDUP Set to the same function as the front panel s [BAND ] button. 33 A=B Set to the same function as the front panel s [A=B] button. 34 A/B Set to the same function as the front panel s [A/B] button. 35 LCK Set to the same function as the front panel s [LCK] button. 36 TUNE Set to the same function as the front panel s [TUNE] button. 37 VICE Announce the current operating frequency (with resolution to the displayed 100 Hz digit) and operating mode. 38 MW Copies the current operating data from the VF into the currently selected memory channel. 39 V/M Toggles frequency control between VF and memory system. 40 HME Recall the Home (favorite frequency) channel. 41 RCL Recall the QMB (Quick Memory Bank) memory. 42 V Activate the V (automatic voice-actuated transmitter switching) feature. 43 ST Copies operating data into QMB (Quick Memory Bank) Memory. 44 STEP Enables the setting of the frequency step of the [DSP/SEL] knob by the [DSP/SEL] knob. 45 SPLIT Activates split frequency operation between VF-A and VF-B. 46 PMS Engages Programmable Memory Scan (PMS). 47 SCAN Initiates the upward scanning of VF frequencies or memory channels. 48 MENU Engage the Menu mode. 49 DIMMER Enables adjustment of the display dimmer level by the [DSP/SEL] knob. 50 MTR Change the meter function in the transmit mode. TABLE Hz 69.3 Hz 71.9 Hz 74.4 Hz 77.0 Hz 79.7 Hz 82.5 Hz 85.4 Hz 88.5 Hz Hz 94.8 Hz 97.4 Hz Hz Hz Hz Hz Hz Hz CTCSS TNE CHART Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz FT-450D CAT PERATIN REFERENCE BK Page 8
10 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES FA FREQUENCY VF-A F A ; F A ; F A ; FB FREQUENCY VF-B F B ; F B ; F B ; (Hz) (Hz) FS FAST STEP F S ; F S ; F S ; FT FUNCTIN T F T ; F T ; F T ; GT AGC FUNCTIN G T ; G T ; G T ; 0: FAST Key FF 1: FAST Key N 0: Transmit the Displayed Band 1: Transmit the ppsite Band 0: Fixed 0: AGC FF 1: AGC FAST 2: AGC SLW 3: AGC SLW 4: AGC AUT ID IDENTIFICATIN 0244 (Fixed value) I D ; I D ; IF INFRMATIN I F ; I F P3 P3 P3 P3 P3 P4 P P6 P7 P8 P9 P9 0 ; (Memory Channel) VF-A Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift Clarifier ffset: (Hz) P4 0: R CLAR FF 1: R CLAR N P5 0: T CLAR FF 1: T CLAR N P6 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: DATA (RTTY-LSB) 7: CW-R 8: USER-L 9: DATA (RTTY-USB) B: FM-N C: USER-U P7 0: VF 1: Memory 2: Memory Tune 3: Quick Memory Bank (QMB) P8 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC P9 Tone Number (See Table 1) 0 0: Simplex 1: Plus Shift 2: Minus Shift Page 9 FT-450D CAT PERATIN REFERENCE BK
11 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES IS IF-SHIFT I S -/+ ; I S ; I S -/+ ; KM KEYER MEMRY Set ~ 43 ** K M ~ ; K M ; Answer ~ 43 ** K M ~ ; 0: Fixed 0000 ~ 1000 (Hz) 1-3 : Beacon Text Channel Number Message Characters (up to 40 characters) KP KEY PITCH K P ; K P ; K P ; KR KEYER K R ; K R ; K R ; 02: 400 Hz 04: 500 Hz 06: 600 Hz 08: 700 Hz 10: 800 Hz 0: KEYER FF 1: KEYER N KS KEY SPEED K S ; K S ; K S ; (WPM) KY CW KEYING K Y ; 6: Beacon Text 1 Playback 7: Beacon Text 2 Playback 8: Beacon Text 3 Playback LK LCK L K ; L K ; L K ; LM LAD MESSEGE L M ; L M ; L M ; 0: DIAL Lock FF 1: DIAL Lock N 0: VICE MEMRY 1: DIGITAL VICE RECRDER When =0 0: VICE MEMRY RECRDING STP 1: VICE MEMRY 1 RECRDING 2: VICE MEMRY 2 RECRDING When =1 0: DIGITAL VICE RECRDER STP 1: DIGITAL VICE RECRDER START MC MEMRY CHANNEL M C ; M C ; M C ; : Memory Channel Number : Regular Memory Channel 501: L Channel 502: U Channel 503: L Channel 504: U Channel FT-450D CAT PERATIN REFERENCE BK Page 10
12 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES MD PERATING MDE 0: Fixed Read M D ; MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: DATA (RTTY-LSB) 7: CW-R 8: USER-L 9: DATA (RTTY-USB) B: FM-N C: USER-U M D ; M D ; MG MIC GAIN M G ; M G ; M G ; MK MDE KEY M K ; : MIC GAIN L : MIC GAIN M : MIC GAIN H KEY 7: MDE UP 8: MDE DWN 9: REVERSE (@CW MDE) ML MNITR LEVEL M L ; M L ; M L ; 0: Fixed 000: MNITR FF 001: MNITR N MR MEMRY CHANNEL READ M R ; M R P3 P3 P3 P3 P3 P4 P P6 P7 P8 P9 P9 0 ; Memory Channel Number Memory Channel Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift Clarifier ffset: (Hz) P4 0: R CLAR FF 1: R CLAR N P5 0: T CLAR FF 1: T CLAR N P6 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: DATA (RTTY-LSB) 7: CW-R 8: USER-L 9: DATA (RTTY-USB) B: FM-N C: USER-U P7 0: VF 1: Memory P8 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC P9: Tone Number (See Table 1) 0 0: Simplex 1: Plus Shift 2: Minus Shift MS METER SW M S ; M S ; M S ; 1: ALC 2: P 3: SWR MW MEMRY CHANNEL WRITE Memory Channel Number Memory Channel Frequency (Hz) M W P3 Clarifier Direction +: Plus Shift, --: Minus Shift Clarifier ffset: (Hz) P3 P3 P3 P3 P3 P4 P P6 P7 P8 P9 P9 0 ; P4 0: R CLAR FF 1: R CLAR N P5 0: T CLAR FF 1: T CLAR N P6 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: DATA (RTTY-LSB) 7: CW-R 8: USER-L 9: DATA (RTTY-USB) B: FM-N C: USER-U P7 0: Fixed P8 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC P9: Tone Number (See Table 1) 0 0: Simplex 1: Plus Shift 2: Minus Shift NA NARRW M A ; N A ; N A ; 0: Fixed 0: Bandwidth Middeum 1: Bandwidth Narrow Page 11 FT-450D CAT PERATIN REFERENCE BK
13 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES NB NISE BLANKER STATUS N B ; N B ; N B ; NR NISE REDUCTIN N R ; N R ; N R ; 0: Fixed 0: Noise Blanker FF 1: Noise Blanker N 0: Fixed 0: Noise Reduction FF 1: Noise Reduction N I PPSITE BAND INFRMATIN I ; I P3 P3 P3 P3 P3 P4 P P6 P7 P8 P9 P9 0 ; Current Memory Channel VF-B Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift Crarifier ffset: (Hz) P4 0: R CLAR FF 1: R CLAR N P5 0: T CLAR FF 1: T CLAR N P6 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: DATA (RTTY-LSB) 7: CW-R 8: USER-L 9: DATA (RTTY-USB) B: FM-N C: USER-U P7 0: VF 1: Memory 2: Memory Tune 3: Quick Memory Bank (QMB) P8 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC P9: Tone Number (See Table 1) 0 0: Simplex 1: Plus Shift 2: Minus Shift S FFSET (REPEATER SHIFT) S ; S ; S ; PA PRE-AMP (IP) P A ; P A ; P A ; PB PLAY BACK P B ; P B ; P B ; PC PWER CNTRL P C ; P C ; P C ; PS PWER SWITCH P S ; P S ; P S ; 0: Fixed 0: Simplex 1: Plus Shift 2: Minus Shift : FM mode only 0: Fixed 0: IP N 1: IP FF 0: STP 1: VICE MEMRY 1 PLAYBACK 2: VICE MEMRY 2 PLAYBACK 6: DIGITAL VICE RECDER PLAYBACK : PWER FF 1: PWER N When the power supply becomes N", the dummy data is sent. The command that makes the power supply N" within two seconds after wait is done for about one second is sent. FT-450D CAT PERATIN REFERENCE BK Page 12
14 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN QI QMB STRE Q I ; CNTRL CMMAND TABLES QR QMB RECALL Q R ; QS QUICK SPLIT Q S ; RA RF ATTENUATR R A ; R A ; R A ; 0: Fixed 0: FF 1: N RC CLAR CLEAR R C ; RD CLARIFIER MINUS FFSET R D ; (Hz) RG RF GAIN R G ; R G ; R G ; RI RADI INFRMATIN R I ; R I ; RL NISE REDUCTIN LEVEL R L ; R L ; R L ; 0: Fixed : Hi-SWR 1: MIC-EQ 3: REC 4: PLAY 0: FF 1: N 0: Fixed Page 13 FT-450D CAT PERATIN REFERENCE BK
15 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES RM READ METER R M ; R M ; RP RESET PWER N R P ; R P ; R P ; RS RADI STATUS R S ; R S ; RT CLAR R T ; R T ; R T ; 0: Depends of the Front Panel s METER Switch 1: S Meter 4: ALC Meter 5: P Meter 6: SWR Meter Resetting the Microprocessor (Full Reset) 0: NRMAL MDE 1: MENU MDE 0: R Clarifier FF 1: R Clarifier N RU CLARIFIER PLUS FFSET R U ; (Hz) SC SCAN S C ; S C ; S C ; SD CW BREAK-IN DELAY TIME S D ; S D ; S D ; SH WIDTH S H ; S H ; S H P3 P3 ; SM S-METER READING S M ; S M ; 0: Scan FF 1: Scan N (Upward) 2: Scan N (Downward) 0:Fixed P3 0000: Full Break-in (msec) (Narrow) (Normal) (Wide) 00 (Narrow) 16 (Normal) 31 (Wide) 0: Fixed FT-450D CAT PERATIN REFERENCE BK Page 14
16 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES SQ SQUELCLH LEVEL S Q ; S Q ; S Q ; ST STEP S T ; S T ; S T ; SV SWAP VF S V ; 0: Fixed FM AM LSB/USB/CW 0: 5.0 khz 2.5 khz 1.0 khz 1: 6.25 khz 5.0 khz 2.5 khz 2: 10.0 khz 9.0 khz 5.0 khz 3: 12.5 khz 10.0 khz 4: 15.0 khz 12.5 khz 5: 20.0 khz 25.0 khz FM 6: 25.0 khz 7: 50.0 khz TS TW T S ; T S ; T S ; 0: TW FF 1: TW N T T SET T ; T ; T ; UL PLL UNLCK STATUS U L ; U L ; 0: RADI T FF CAT T FF 1: RADI T FF CAT T N 2: RADI T N CAT T FF (Answer) 0: PLL Lock 1: PLL Unlock UP MIC UP U P ; VD V DELAY TIME V D ; V D ; V D ; ms (100 ms multiples) VG V GAIN V G ; V G ; V G ; Page 15 FT-450D CAT PERATIN REFERENCE BK
17 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES VM [V/M] KEY FUNCTIN V M ; Toggles the frequency control between the VF and Memory system. VR VICE V R ; V R ; V R ; VS VF SELECT V S ; V S ; V S ; VV VF T VF V V ; V V ; V V ; V V STATUS V ; V ; V ; 0: VICE FF 1: VICE 1 N 2: VICE 2 N 0: VF-A 1: VF-B Copy the displayed VF data to the opposite VF. 0: V FF 1: V N FT-450D CAT PERATIN REFERENCE BK Page 16
18 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN Copyright 2017 YAESU MUSEN C., LTD. All rights reserved No portion of this manual may be reproduced without the permission of YAESU MUSEN C., LTD B FT-450D CAT PERATIN REFERENCE BK
NOTE FTDX9000 CAT OPERATION REFERENCE BOOK FTDX9000 OPERATING MANUAL
NTE FTD9000 CAT PERATIN REFERENCE BK FTD9000 PERATING MANUAL CAT (CMPUTER AIDED TRANSCEIVR) PERATIN VERVIEW The CAT (Computer Aided Transceiver) System in the FTD9000 provides control of frequency, VF,
More informationCAT (COMPUTER AIDED TRANSCEIVER) OPERATION FT-950 CAT OPERATION FT-950 CAT OPERATION REFERENCE BOOK
CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FT-950 CAT PERATIN REFERENCE BK FT-950 CAT PERATIN REFERENCE BK CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver) System in the
More informationCAT (COMPUTER AIDED TRANSCEIVER) OPERATION
CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FTD5000 SERIES CAT PERATIN REFERENCE BK FTD5000 SERIES CAT PERATIN REFERENCE CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver)
More informationCAT (COMPUTER AIDED TRANSCEIVER) OPERATION
CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FT-2000 SERIES CAT PERATIN REFERENCE BK FT-2000 SERIES CAT PERATIN REFERENCE BK CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver)
More informationCAT (COMPUTER AIDED TRANSCEIVER) OPERATION
CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FT D 9000 SERIES CAT PERATIN REFERENCE BK FT D 9000 SERIES CAT PERATIN REFERENCE CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver)
More informationFTDX3000 SERIES CAT OPERATION REFERENCE BOOK YAESU MUSEN CO., LTD.
FTD3000 SERIES CAT PERATIN REFERENCE BK YAESU MUSEN C., LTD. CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver) System in the FTD3000 transceiver provides control of frequency,
More informationFT-891 YAESU MUSEN CO., LTD.
FT- CAT Operation Reference Book YAESU MUSEN CO., LTD. Overview The CAT (Computer Aided Transceiver) System in the FT- transceiver provides control of frequency, VFO, memory, and other settings such as
More informationCAT Operation Reference Manual
CAT Operation Reference Manual YAESU MUSEN CO., LTD. Overview The CAT (Computer Aided Transceiver) System in the FT-99 transceiver provides control of frequency, VFO, memory, and other settings such as
More informationFT-991. reference BOOk YAESU MUSEN CO., LTD.
FT- CAT OperATiOn reference BOOk YAESU MUSEN CO., LTD. Overview The CAT (Computer Aided Transceiver) System in the FT- transceiver provides control of frequency, VFO, memory, and other settings such as
More informationTS-590S TS-590SG. PC CONTROL COMMAND Reference Guide
TS-590S TS-590SG PC CONTROL COMMAND Reference Guide January/30/2019 PC CONTROL COMMAND REFERENCE GUIDE ABOUT THIS REFERENCE GUIDE All descriptions in this reference guide are for the user s convenience.
More informationSPECS FEATURES SUPPLIED ACCESSORIES. HF All Band Transceiver
718 HF All Band Transceiver RX 0.030-29.999999MHz* TX 1.800-1.999999 MHz** 3.500-3.999999 MHz** 7.000-7.300000 MHz 10.100-10.150000 MHz 14.000-14.350000 MHz 18.068-18.168000 MHz 21.000-21.450000 MHz 24.890-24.990000
More informationIcom IC-9100 HF/VHF/UHF transceiver
263 Walsall Road, Great Wyrley, Walsall, WS6 6DL Established 1997. Open Monday - Friday 9am - 5pm and Saturday 9.30am - 4pm Tel: 01922 414 796 Fax: 01922 417829 Skype: radioworld_uk Icom IC-9100 HF/VHF/UHF
More informationFT-450 OPERATION MANUAL HF/50 MHZ TRANSCEIVER
HF/50 MHZ TRANSCEIVER FT-450 OPERATION MANUAL VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A.
More informationFT-991 Firmware Update Information
FT-991 Firmware Update Information This update adds the DG-ID function and the DP-ID function in the digital C4FM mode of the FT- 991 and is compatible with the System Fusion II digital repeater DR-2X.
More informationFT-991 MENU MODE. changes in factory defaults are yellow
changes in factory defaults are yellow FT-991 MENU MODE No. Menu Function Available Settings Default Value 001 AGC FAST DELAY 20-4000 (20msec/step) 300msec 002 AGC MID DELAY 20-4000 (20msec/step) 700msec
More informationLD5 CW/SSB QRP Transceiver SDR /DSP
LD5 CW/SSB QRP Transceiver SDR /DSP Quick guide manual Description: At the development base of the digital signal processing unit, an algorithm is embedded for IQ processing of the channels with phase
More informationFT-897 Alignment. Local Oscillator Adjustment. PLL Adjustment
FT-897 Local Oscillator Adjustment Reference Frequency Adjustment a. Connect a frequency counter to TP1032. b. Adjust the trimmer capacitor (TC5001) for 67.875000MHz ±5Hz on the frequency counter. c. Connect
More informationLnR Precision, Inc. 107 East Central Avenue, Asheboro, NC
LD5 CW/SSB QRP Transceiver Quick guide manual Description: At the development base of the digital signal processing unit, an algorithm is embedded for IQ processing of the channels with phase suppression
More informationApplication for FCC / IC FCC ID: K X50 IC: 511B HF/50 MHz Transceiver FT-410 Operation Manual YAESU MUSEN CO., LTD. Tennozu Parkside Build
HF/50 MHz Transceiver FT-410 Operation Manual YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress, CA 90630,
More informationBLOCK DIAGRAM - I J Li) N 6. w IS) AF D RIVE R R F D RIVE R R F P OWE R AMP PL L OSC UNIT. LL co X X X Lti X. C X W N O C..) 4 C.
MODEL 1-632 BLOCK DIAGRAM tl LL co a. LL O ox X X X X < X C.) W N C U) LL CO aa 1.11 t O - I J Ul Li) Lti N w IS) 1 X. C X Ir t AF D RIVE R X - LL C.) CD r.--1111 MOP U) N N 6 PL L OSC UNIT R F D RIVE
More informationSERIAL INPUT AND SERIAL OUTPUT These ports are used for communications between the main CPU (controller) and the sub CPU.
IC-901 CPU SERIAL DATA CONTROL SERIAL INPUT AND SERIAL OUTPUT These ports are used for communications between the main CPU (controller) and the sub CPU. When the operation interrupt START BIT is applied
More informationKenwood TH-G71 Protocol Specification
Kenwood TH-G71 Protocol Specification This document describes the serial commands used to program and control the TH-G71 radio via its serial port. Some of this data was initially based on information
More informationTS-590S ADJUSTMENT. Updating the Firmware. Required Test Equipment. Preparation
Updating the Firmware The firmware of the main MCU and DSP can be updated using the TS590 Update update software. Update the firmware according to the procedure displayed in update software. Refer to the
More informationThe Icom IC Adam Farson VA7OJ. A New Top-class HF/6m Transceiver. IC-7700 Information & Links
The Icom IC-7700 A New Top-class HF/6m Transceiver Adam Farson VA7OJ IC-7700 Information & Links Copyright 2008 North Shore Amateur Radio Club NSARC HF Operators IC-7700 1 IC-7700 front panel This is a
More informationIC-400pro - RADIOAFICION.COM
PROCEDURES IC-400pro - 5- PREPARATION When you adjust the contents on pages 5-5 and 5-6, SOFT- WARE, the optional CS-400PRO ADJ SOFTWARE (Rev..0 or later), *OPC- JIG CABLE (modified OPC- CLONING CABLE;
More informationFT-991. HF/VHF/UHF All Mode Transceiver
HF/VHF/UHF All Mode Transceiver FT-991 Operating Manual YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress,
More informationThe amazing evolution of the 706 series
The amazing evolution of the 706 series The IC-706MKIIG carries on the 706 series tradition of base station performance and features in a mobile reg-sized package. Building on this legacy, frequency coverage
More informationFrequency Coverage MHz RF Power Output 30W SSB / 9W AM/ 30W FM Dual Finals on Heat Sink Modes AM, FM, USB, LSB Microprocessor
MAGNUM M-257 30W AM/ /FM/SSB 10--11 Meterr Mobile Trranscei ivverr n Prri iiccee: : US$ 250..00 eexx ssttoocckk JJaakkaarrttaa (Arrrri ( iivvi iinngg 2 d weeeekk iinn i Maarrcchh) ) SPECIFICATIONS Frequency
More informationHF/VHF/UHF ALL MODE TRANSCEIVER FT-818
HF/VHF/UHF ALL MODE TRANSCEIVER FT-818 Operating Manual Contents Introduction...1 Accessories & Options...2 Supplied Accessories...2 Available Options...2 Plug Pinout...3 Installation...4 Connecting the
More informationWayne Burdick, N6KR Rev. A3, Applies to firmware revision 2.61 or later.
ELECRAFT KX2 PHYSICAL DESCRIPTION AND AUDIO-CW USER INTERFACE Wayne Burdick, N6KR Rev. A3, 5-31-2016 Applies to firmware revision 2.61 or later. CHANGE HISTORY Rev. A1, 5-23-2016: Document creation. Rev.
More informationTechnician License Course Chapter 5. Lesson Plan Module 11 Transmitters, Receivers and Transceivers
Technician License Course Chapter 5 Lesson Plan Module 11 Transmitters, Receivers and Transceivers Generalized Transceiver Categories Mobile Single Band Dual Band All Band Multimode Handheld (HT) VHF/UHF
More informationmat-30 HF-SSB Automatic Antenna Tuner Instruction Manual Version V1.0
INTRODUCTION mat-30 HF-SSB Automatic Antenna Tuner Instruction Manual Version V1.0 The mat-30 is an automatic tuner intended for use with modern Yaesu transceivers. It works with some Yaesu transceiver
More informationKENWOOD SKY COMMAND SYSTEM
KENWOOD SKY COMMAND SYSTEM Operation Manual KENWOOD COMMINICATIONS CORPORATION KENWOOD COMMUNICATIONS CORPORATION This operation manual is used for the KENWOOD SKY COMMAND SYSTEM (hereinafter referred
More informationi78 INSTRUCTION MANUAL HF TRANSCEIVER
INSTRUCTION MANUAL HF TRANSCEIVER i78 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
More informationTS-890S. PC CONTROL COMMAND Reference Guide
TS-890S PC CONTROL COMMAND Reference Guide August/30/2018 PC CONTROL COMMAND REFERENCE GUIDE ABOUT THIS REFERENCE GUIDE All descriptions in this reference guide are for the user s convenience. JVC KENWOOD
More informationAM/FM/SSB/CW 12 & 10 METER MOBILE AMATEUR TRANSCEIVER OWNER S MANUAL
AM/FM/SSB/CW 12 & 10 METER MOBILE AMATEUR TRANSCEIVER OWNER S MANUAL TABLE OF CONTENTS Warranty...2 Introduction...3 Installation... 4-5 Front Panel Controls... 6-8 Microphone...8 Menu Settings... 9-11
More informationTN910 Daniels MT-3 and IFR COM-120 by Aeroflex Test Procedures
TN10 Daniels MT-3 and IFR CM-120 by eroflex Test Procedures Technical Note for Tuning, Testing Maintaining and Servicing MT-3 nalog Radio Systems with the IFR CM-120 (B or C) by eroflex Daniels Electronics
More informationCat. No OWNER S MANUAL. HTX-212 Two-Meter Mobile Transceiver. Please read before using this transceiver.
19-1125.fm Page 1 Tuesday, August 3, 1999 9:47 AM Cat. No. 19-1125 OWNER S MANUAL HTX-212 Two-Meter Mobile Transceiver Please read before using this transceiver. 19-1125.fm Page 2 Tuesday, August 3, 1999
More informationElmer Session Hand Out for 3/3/11 de W6WTI. Some Common Controls Found On Amateur Radio Transceivers. (From ARRL web site tutorial)
Elmer Session Hand Out for 3/3/11 de W6WTI Some Common Controls Found On Amateur Radio Transceivers. (From ARRL web site tutorial) The placement of the controls may vary from manufacturer to manufacturer
More informationSUBELEMENT T4. Amateur radio practices and station set up. 2 Exam Questions - 2 Groups
SUBELEMENT T4 Amateur radio practices and station set up 2 Exam Questions - 2 Groups 1 T4A Station setup: connecting microphones; reducing unwanted emissions; power source; connecting a computer; RF grounding;
More informationADMS-847 Programming Software for the Yaesu FT-847
for the Yaesu FT-847 Memory Types Memories Limit Memories VFO A VFO B Home Satellite Memories One Touch Memory Channel Functions Transmit Frequency Offset Frequency Offset Direction CTCSS DCS Skip The
More informationINSTRUCTION MANUAL REMOTE CONTROL SOFTWARE RS-R75
INSTRUCTION MANUAL REMOTE CONTROL SOFTWARE RS-R75 IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the receiver. SAVE THIS INSTRUCTION MANUAL This instruction manual contains important
More informationi2820h (USA) ie2820(europe)
January 2007 DUAL BAND TRANSCEIVERS i2820h (USA) ie2820(europe) The above photo shows the IC-2820H. The IC-E2820 differs slightly from this photo. Icom proudly announces the debut of the new dual band
More informationSEA 235 OPERATOR S MANUAL Digital Single Sideband Radiotelephone
SEA 235 OPERATOR S MANUAL Digital Single Sideband Radiotelephone TABLE OF CONTENTS GENERAL OPERATIONS...1 TECHNICAL SPECIFICATIONS...1 GENERAL INFORMATION...2 UNDERSTANDING CHANNEL MEMORY...3 LCD DISPLAY
More informationCI-V REFERENCE GUIDE. HF/50MHz TRANSCEIVER. i7610
CI-V REFERENCE GUIDE HF/50MHz TRANSCEIVER i7610 Table of contents Remote control 2 Remote control (CI-V) information 2 DDCI-V connection 2 DDPreparing 2 DDAbout the data format 2 DDCommand table 3 DDCommand
More informationPARA Field Day 2010 Digital GOTA Station Setup 6/12/2010
PARA Field Day 2010 Digital GOTA Station Setup dranch@trinnet.net 6/12/2010 Table of Contents Physically connecting up the radio...2 Configure the FT-897...2 Initial Signalink settings...2 Initial Windows
More informationi746 INSTRUCTION MANUAL VHF/HF ALL MODE TRANSCEIVER
INSTRUCTION MANUAL VHF/HF ALL MODE TRANSCEIVER i746 This device complies with Part 5 of the FCC rules. Operation is subject to the following two conditions: () This device may not cause harmful interference,
More informationChapter 15: Serial Controlled (HF) Radio Support
15-1 Chapter 15: Serial Controlled (HF) Radio Support This section describes the controller's interface for serial controlled radios. Most such radios are for the HF bands, but some such as the FT-736
More informationINSTRUCTION MANUAL. HF/VHF ALL MODE TRANSCEIVER i746pro
INSTRUCTION MANUAL HF/VHF ALL MODE TRANSCEIVER i746pro This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
More informationELAD FDM-DUO Dual Mode SDR Transceiver USER MANUAL
ELAD FDM-DUO Dual Mode SDR Transceiver USER MANUAL www.eladit.com Contents Revision History... 4 1 Overview... 5 1.1 Notice... 5 1.2 Firmware versions... 5 1.3 Introduction... 5 1.3.1 Main Features...
More informationBefore using your FT-950, be sure to read and follow the instructions in the Before You Begin section of this manual.
About This Manual... The FT-950 is a leading-edge transceiver with a number of new and exciting features, some of which may be unfamiliar to you. In order to gain the most enjoyment and operating efficiency
More informationGRAND STRAND AMATEUR RADIO CLUB
The GRAND STRAND AMATEUR RADIO CLUB (GSARC) Myrtle Beach SC is offering used amateur related equipment for sale. Written bids may be submitted to the GSARC up to Friday, November 23 rd, 2018. Only currently
More informationE L E C R A F T K 2 R E V I S I O N 2 F I R M W A R E
E L E C R A F T K 2 R E V I S I O N 2 F I R M W A R E Installation and Reference Manual Rev. B, August 28, 2001 Summary of Changes... 2 Computer Control (KIO2)... 2 Transverter Bands... 2 RTTY/Data Mode
More informationMaxon Motor & Motor Controller Manual
Maxn Mtr & Mtr Cntrller Manual Nte: This manual is nly fr use fr the Maxn mtr and cntrller utlined belw. This infrmatin is based upn the tutrial vides fund nline and thrugh testing. NOTE: Maximum Permitted
More informationINSTRUCTION MANUAL. Version: /440 MHz FM DUAL BANDER TM-D710GA. 144/430 MHz FM DUAL BANDER TM-D710GE
INSTRUCTION MANUAL 144/440 MHz FM DUAL BANDER TM-D710GA 144/430 MHz FM DUAL BANDER TM-D710GE Version: 1.01 CONTENTS OPERATING THROUGH REPEATERS...REPEATER- REPEATER ACCESS... 1 Selecting an Offset Direction...
More informationINSTRUCTION MANUAL. Version: /440 MHz FM DUAL BANDER TM-D710GA. 144/430 MHz FM DUAL BANDER TM-D710GE
INSTRUCTION MANUAL 144/440 MHz FM DUAL BANDER TM-D710GA 144/430 MHz FM DUAL BANDER TM-D710GE Version: 1.00 CONTENTS OPERATING THROUGH REPEATERS...REPEATER- REPEATER ACCESS... 1 Selecting an Offset Direction...
More informationLNR Precision Mountain Topper MTR-4B and MTR-5B REV 2.0 User Manual for use with versions with 16 x 2 display.
LNR Precision Mountain Topper MTR-4B and MTR-5B REV 2.0 User Manual for use with versions with 16 x 2 display. Four band MTR 4B shown Overview: The Mountain Topper Rigs are designed to be a very small,
More informationMastr III P25 Base Station Transmitter Tune-up Procedure
Mastr III P25 Base Station Transmitter Tune-up Procedure 1. Overview The Mastr III Base Station transmitter alignment is performed in several steps. First, the Transmit Synthesizer module is aligned to
More informationI.D.A. Operation manual
TRX-200 Wide ide Band Receiver Operation manual Thank you for purchasing the TRX-200 all modes wide band monitoring receiver. Please read this operating manual carefully to avoid miss operation of the
More informationYaesu FT-991A HF, VHF, and UHF Transceiver
Mark J. Wilson, K1RO, k1ro@arrl.org Product Review Yaesu FT-991A HF, VHF, and UHF Transceiver Reviewed by Joel R. Hallas, W1ZR QST Contributing Editor w1zr@arrl.org The FT-991A is a compact SSB, CW, AM,
More informationINSTRUCTION MANUAL COMMUNICATIONS RECEIVER. ir75
INSTRUCTION MANUAL COMMUNICATIONS RECEIVER ir75 IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the receiver. SAVE THIS INSTRUCTION MANUAL. This manual contains important
More informationPushing performance to the pinnacle
Pushing performance to the pinnacle The latest DSP technologies developed for the IC-7800/7700 plus over 45 years of analog circuit expertise give the IC-7600 the performance advantage. The flagship's
More informationReference for UV-5R Menus by Jim Unroe - KC9HI 2-April-2014
Long Name / Description / / Notes / 0 SQL Carrier Squelch Mutes the speaker of the transceiver in the absence of a strong signal. VHF squelch is either OFF or ON. UHF squelch is either OFF or one of 9
More informationCode Master. Model CWR-610E OPERATING INSTRUCTIONS
Code Master Model CWR-610E OPERATING INSTRUCTIONS CONTENTS RATING... 3 DESCRIPTION OF PANELS... 5 METHOD OF USE Preparation... 7 Reception of CW... 7 Code interpretable range and word space... 7 Reception
More informationINSTRUCTION MANUAL. HF/50 MHz ALL MODE TRANSCEIVER
INSTRUCTION MANUAL HF/50 MHz ALL MODE TRANSCEIVER This device complies with Part 5 of the FCC rules. Operation is subject to the following two conditions: () This device may not cause harmful interference,
More informationTABLE OF CONTENTS 8 SOFTWARE MENU MODE SETTINGS SOFTWARE MENU QUICK GUIDE SERVICE MODE... 24
1 TABLE OF CONTENTS 1. TABLE OF CONTENTS......................... 2 2. INTRODUCTION............................. 3 3. SPECIFICATIONS............................ 4 4. ACCESSORY PACKAGE.......................
More informationWORLD BAND RADIO. AM/FM/SW/L W/AIR Band /SSB radio with LCD backlight OWNER S MANUAL
WORLD BAND RADIO AM/FM/SW/L W/AIR Band /SSB radio with LCD backlight display and keypad direct entry OWNER S MANUAL WARNING Do not expose this appliance to rain or moisture Do not submerge or expose to
More informationTHE TRANSCEIVER Instruction Manual
THE TRANSCEIVER i7800 Instruction Manual A-6328H-1EX-q Printed in Japan 2004 Icom Inc. FOREWORD Congratulations! You are the owner of the world s most advanced amateur HF/50 MHz transceiver IC-7800. The
More informationINSTRUCTION MANUAL CONTROL PANEL RC-D710. Version: 2.10
INSTRUCTION MANUAL CONTROL PANEL RC-D710 Version: 2.10 CONTENTS File name (TM-D710_) Operation OPERATING THROUGH REPEATERS...REPEATER- 01_REPEATER_E.pdf OPERATING THROUGH REPEATERS...1 REPEATER ACCESS...1
More informationINSTRUCTION MANUAL. 144/ 430 MHz FM DUAL BANDER TH-F7A B (M) FM DUAL BANDER TH-F7
INSTRUCTION MANUAL FM DUAL BANDER TH-F7 144/ 430 MHz FM DUAL BANDER TH-F7A B62-1899-00 (M) 09 08 07 06 05 04 03 02 01 00 THANK YOU THANK YOU Thank you for choosing this KENWOOD TH-F7A transceiver. It has
More informationINSTRUCTION MANUAL. HF/ 50 MHz ALL MODE TRANSCEIVER TS-590S
INSTRUCTION MANUAL HF/ 50 MHz ALL MODE TRANSCEIVER TS-590S NOTIFICATION This equipment complies with the essential requirements of Directive 1999/5/EC. The use of the warning symbol means the equipment
More informationFTDX5000 SERIES OPERATING MANUAL HF/50 MHZ TRANSCEIVER
HF/50 MHZ TRANSCEIVER FTDX5000 SERIES OPERATING MANUAL VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD U.S.A. Inc. 6125 Phyllis Drive, Cypress, California 90630,
More informationRigExpert TI-7 USB Transceiver Interface User s manual
RigExpert TI-7 USB Transceiver Interface User s manual Please read this manual before attempting to use the RigExpert TI-7 device. - - 2 - Table of contents 1. What is a RigExpert TI-7?... 4 2. Specifications...
More information1. Your new Eagle 599 3
Table of Contents 1. Your new Eagle 599 3 1.1. Unpacking Eagle 599 3 1.2. About this Manual 3 1.3. Accessory package 3 1.4. Connection to Antenna & Power Supply 4 1.5. A word about grounding 4 1.6. Philosophy
More informationELECRAFT KX3 EXTENDED VFO TEMPERATURE COMPENSATION PROCEDURE Copyright 2012 Elecraft LLC Rev. A9, November 14, 2012
ELECRAFT KX3 EXTENDED VFO TEMPERATURE COMPENSATION PROCEDURE Copyright 2012 Elecraft LLC Rev. A9, November 14, 2012 Introduction The KX3 standard VFO temperature compensation is entirely adequate for most
More informationTS-590S INSTRUCTION MANUAL. HF/ 50 MHz ALL MODE TRANSCEIVER
INSTRUCTION MANUAL HF/ 50 MHz ALL MODE TRANSCEIVER TS-590S NOTIFICATION This equipment complies with the essential requirements of Directive 1999/5/EC. The use of the warning symbol means the equipment
More informationFT-991. HF/VHF/UHF All Mode Transceiver
HF/VHF/UHF All Mode Transceiver FT-991 Operating Manual YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress,
More informationHF/50MHz TRANSCEIVER
HF/50MHz TRANSCEIVER D isplay Pushing performance to the pinnacle The latest DSP technologies developed for the flagship models plus many decades of analog circuit expertise give the the performance advantage.
More informationYCE13. Dealer PC Programming Software Reference Manual. Attention!
YCE13 Dealer PC Programming Software Reference Manual Attention! The YCE13 programing software can only be used with HX380/400 firmware version Ver. 2.00 or later. This software is used to program the
More informationWIRES-X Portable Digital Node Function. Instruction Manual
Wide-Coverage Internet Repeater Enhancement System WIRES-X Portable Digital Node Function Instruction Manual Please read this Instruction Manual carefully for appropriate procedure. Preparation Procedure
More informationFT-891. Operating Manual. HF/50MHz TRANSCEIVER
FT-891 Operating Manual HF/50MHz TRANSCEIVER Contents Introduction... 1 Safety Precautions... 2 Accessories & Options... 5 Supplied Accessories... 5 Optional Accessories... 5 Installing the Radio... 6
More informationAmateur Station Control Protocol (ASCP) Ver Oct. 5, 2002
Amateur Station Control Protocol (ASCP) Ver. 0.17 Oct. 5, 2002 Moe Wheatley, AE4JY Table of Contents 1. Purpose...4 2. Basic Protocol Concepts...5 3. Message Block Format...8 3.1. Detailed Description
More informationINSTRUCTION MANUAL VHF/UHF ALL MODE TRANSCEIVER. i910h
INSTRUCTION MANUAL VHF/UHF ALL MODE TRANSCEIVER i910h IMPORTANT EXPLICIT DEFINITIONS READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the transceiver. SAVE THIS INSTRUCTION MANUAL. This
More informationTI RigExpert. User s manual. USB Transceiver Interface
TI-5000 RigExpert USB Transceiver Interface User s manual . Table of contents Introduction Operating the TI-5000 Front and rear panels Transceiver and computer connection Updating the firmware Annexes
More informationINSTRUCTION MANUAL ALL MODE MULTI-BAND TRANSCEIVER TS-2000 TS-2000X TS-B2000
B6--50 (K, E) 09 08 07 06 05 ALL MODE MULTI-BAND TRANSCEIVER TS-000 TS-000X TS-B000 INSTRUCTION MANUAL NOTIFICATION This equipment complies with the essential requirements of Directive 999/5/EC. The use
More informationTS-590SG HF/ 50MHz All-Mode TRANSCEIVER_
New Product Release Information Oct 2014 TS-590SG HF/ 50MHz All-Mode TRANSCEIVER_ Kenwood introduces Updated to new G version new HF/50MHz All-Mode Transceiver Four years ago we launched our best-selling
More informationMidland 248XL I NSTRUCTION GUI DE
Midland 248XL I NSTRUCTION GUI DE INDEX Introduction...2 Function and location of the controls...3 Installation...7 Power supply...7 Installing an antenna...7 How to use your Midland 248XL...8 Frequency
More informationYaesu FT-25R 2-Meter Handheld Transceiver
Yaesu FT-25R 2-Meter Handheld Transceiver Reviewed by Dan Wall, W1ZFG ARRL LoTW Administration w1zfg@arrl.org The latest entry into the field of small, inexpensive handhelds is the Yaesu FT-25R. This is
More informationTABLE OF CONTENTS TABLE OF CONTENTS 1
TABLE OF CONTENTS TABLE OF CONTENTS 1 Chapter 1 YOUR NEW ORION II ORION II ANOTHER STEP FORWARD IN TEN-TEC INNOVATION 4 UNPACKING YOUR NEW ORION II 4 ABOUT THIS MANUAL 4 CONNECTING A POWER SUPPLY 5 A WORD
More information200GTL ALIGNMENT REVISION: 1.0 BURKE MODEL: 200GTL REVISION: 1.2 DATE: 02/14/06. Total Pages: 6 pages. Page:1 print date: 9/23/09
ALIGNMENT PROCEDURE MODEL: 200GTL REVISION: 1.2 DATE: 02/14/06 PREPARED BY: BURKE Total Pages: 6 pages Page:1 print date: 9/23/09 1 TEST CONDITION: 200GTL ALIGNMENT INSTRUCTION 1.0. TEST TEMPERTAURE: 77
More informationAR-DN-RS232. An-10 / Rapid RS232 Interface. Product Guide. Overview. Features
AR-DN-RS232 An-10 / Rapid RS232 Interface Product Guide Overview The AR-DN-RS232 is a device that is used as a 2 way gateway between third party systems and the CP An-10 or Rapid lighting control systems
More informationOPERATING GUIDE VHF TRANSCEIVER. Iç-G88
OPERATING GUIDE VHF TRANSCEIVER Iç-G88 INTRODUCTION PREFACE We appreciate you choosing Icom for your communication needs. The MDC 1200 signaling system is built into your IC-G88 vhf transceiver. IMPORTANT
More informationINSTRUCTION MANUAL. HF/50 MHz TRANSCEIVER. i7200
INSTRUCTION MANUAL HF/ MHz TRANSCEIVER i IMPORTANT R E A D T H I S I N S T RU C T I O N M A N UA L CAREFULLY before attempting to operate the transceiver SAVE THIS INSTRUCTION MANUAL This manual contains
More informationINSTRUCTION MANUAL. HF/50 MHz ALL MODE TRANSCEIVER i756pro
INSTRUCTI MANUAL HF/50 MHz ALL MODE TRANSCEIVER i756pro IMPORT EXPLICIT DEFINITIS READ THIS INSTRUCTI MANUAL CAREFULLY before attempting to operate the transceiver. SAVE THIS INSTRUCTI MANUAL. This manual
More informationTECHNICAL INFORMATION BULLETIN
TECHNICAL INFORMATION BULLETIN T/B No.: TIBFM 15-02 Rev A Revision date: JUNE24/08 Issue Date: JUNE18/08 TiL Model: TDFM-600/6000/7000 transceivers with Type I or Type II modules. TiL P/N: 011210-1,-2,-3,-4,-5
More informationCAT-700B Repeater Controller Computer Automation Technology, Inc
CAT-00B Repeater Controller Computer Automation Technology, Inc N.W. st Avenue, Suite Fort Lauderdale, Florida 0 Phone: () 8- Fax: () 88-8 Internet: http://www.catauto.com Table of Contents Chapter Page.
More informationINSTRUCTION MANUAL. HF/50 MHz TRANSCEIVER. i7410
INSTRUCTION MANUAL HF/0 MHz TRANSCEIVER i0 i FOREWORD Thank you for making the IC-0 your radio of choice. We hope you agree with Icom s philosophy of technology first. Many hours of research and development
More informationFTDX5000 OPERATING MANUAL SERIES HF/50 MHZ TRANSCEIVER
HF/50 MHZ TRANSCEIVER FTDX5000 SERIES OPERATING MANUAL VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630,
More informationBAND DECODER and CONTROLLE R. Accessibility Upgrade and Operating Instructions
ELE CRAFT KRC2 BAND DECODER and CONTROLLE R Accessibility Upgrade and Operating Instructions Revision A, March 4, 2004. Copyright 2004, Elecraft; All Rights Reserved Introduction The KRC2 Accessibility
More informationINSTRUCTION MANUAL HF ALL BAND TRANSCEIVER. i718
INSTRUCTION MANUAL HF ALL BAND TRANSCEIVER i718 IMPORTANT EXPLICIT DEFINITIONS READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL This instruction
More information