Operating Manual IMPORTANT NOTE: A Watt Mixer Amplifier. Redback Proudly Made In Australia

Transcription

1 Operating Manual A Watt Mixer Amplifier edback Proudly Made In Australia Distributed by Altronic Distributors Pty. td. Phone: Fax: Internet: IMPOTANT NOTE: Please read these instructions carefully from front to back prior to installation. They include important setup instructions. Failure to follow these instructions may prevent the amplifier from working as designed. User manual revision number: /09/2015

2 EDBACK is a registered trademark of Altronic Distributors Pty td Since 1976 edback amplifiers have been manufactured in Perth, Western Australia by Altronics. With over 5 years experience in the commercial audio industry, we offer consultants, installers and end users reliable products of high build quality with local product support. We believe there is significant added value for customers when purchasing an Australian made edback amplifier or PA product Australian Made Status All edback house products made by Altronics will now be sporting the official Australian Made logo. Since starting manufacturing of commercial audio equipment in the mid 70 s we have always taken pride in producing a quality local product. The new adoption of the Australian Made logo will help us get the word out to local and export markets that our products carry the official compliance seal of the Australian Made campaign. We have always pushed our local is better line in all of our marketing efforts, it s always an added boost when you are backed up by a widely recognised and respected icon. Industry leading 10 year warranty. There s a reason we have the industry leading DECADE warranty. It s because of a long tried and tested history of bulletproof reliability. We ve heard PA contractors tell us they still see the original edford amplifier still in service in schools - that s over 7 years of operation - and still going strong! Published by Altronic Distributors 2015 Altronic Distributors 2 edback Proudly Made In Australia

3 OVEVIEW The edback A 495 is a 500 Watt Mixer amplifier for installations requiring a high power zone amplifier. Ideally suited for use in shopping centres, pedestrian precincts, public transport facilities and convention centres. The amplifier has two audio inputs, with input 1 either a balanced X input or dual CA line input, and input 2 a dual CA. There is also a music input on the front of the amplifier for connection of portable devices. This input when connected, over-rides the rear input 2 audio source and is adjusted via the volume 2 level control. A VOX circuit with front panel sensitivity adjustment, allows input 1 to mute input 2. Phantom power (15 volts) is available at the pin X on input 1 and both inputs 1 and 2 have adjustable input sensitivies. The amplifier has a host of protection circuitry including over current, over voltage and short circuit protection. FEATUES obust design incorporating latest Mosfet technology Very ow noise and distortion 70V, 100V and 4-16Ω outputs 240V AC or 1 Amp output for external devices 00mA battery trickle charge Adjustable input level sensitivities Bass and Treble controls Phantom power on microphone input (X Input 1) Multi stage thermally cued fan cooling Output Peak imited Thermal Overload protected Signal Presence Indicators Fault Indicators Power Status Indicators ack Mountable (suits 19 inch racks) edback Proudly Made In Australia

4 Fig 1 shows the layout of the front panel. 500W Public Address Mixer Model : A 495 Volume 1 Volume 2 Treble Bass 4 6 VOX Sens. 2 8 Music Input Signal Status Fault Status Power Status Present Peak imit VOX Active Over Temp Current imit Shut Down Mains On Power Fig 1 1 Bass and Treble Controls Use these controls to adjust the bass and treble. 2 Vox level control Use this control to adjust the vox sensitivity of input 1. Input 1 volume control Use this control to adjust the output volume of input 1. 4 Music Input Use this input to connect a portable music player. This input over-rides the rear input 2 and is adjusted via the volume 2 pot. 5 Input 2 volume control Use this control to adjust the output volume of input 2. 6 Signal Presence Indicator This ED indicates when an input signal is present. 7 Peak imit Indicator This ED indicates when the input signal is clipping. 8 VOX Active Indicator This led indicates when the VOX muting is active. 9 Over Temp Indicator This ED indicates when the amplifier is overheating. The output will be disconnected until the amplifier is once again cool enough to operate. 10 Current imit Indicator This ED indicates when the output is drawing too much current from the amplifier. The output will be disconnected until the current draw is reduced. 11 Shut Down Indicator This ED indicates when the amplifier has an over temp occurrence or if the internal circuitry has a fault. 12 Indicator This ED indicates when the amplifier is being powered from the 24V input. 1 Mains Indicator This ED indicates when the amplifier is being powered from the mains (20V AC). 14 On Indicator This ED indicates the unit has power. 15 Power Switch Use this to turn the unit on. 4 edback Proudly Made In Australia

5 Fig 2 shows the layout of the rear panel. CAUTION ISK OF EECTIC SHOCK OPEN BY QUAIFIED PESONNE ONY! 20V 50Hz (Fuse 10A M205) Made in Australia by Altronic Distributors Pty td OUTPUTS 100V 70V 4-16Ω DIP Switch Settings SW Item On Off Input 1 Sensitivity 1V 0.1V On Off Phantom Power Mic On Off Input 2 Sensitivity 1V 0.1V 1 2 VOX Enable 4 OUT (1A Max) ESETTABE FUSE 20 AMP ESETTABE FUSE 20 AMP INK TO CHAGE BACKUP BATTEY INPUT Input 1 Balanced Mic Input 2 DIP Switches _ 1 Shield 2 Hot Cold Balanced Mic Wiring Fig 2 1 Output Connections Speakers with total impedance of 4 to 16 ohms, or speakers fitted with a 70V/100V line transformer may be connected. Always ensure that the total load of the speakers does not exceed the rated output of the amplifier ie either 4Ω minimum for the 4-16Ω terminals or 20Ω minimum at 100V for 500W. Otherwise either the DC or mains fuse could blow or the fault led activate and the amp will shut down. Always be careful to avoid short circuits and connection to the wrong terminals. 2 24V 1A output A constant 24V output terminal has been provided to power ancilliary 24V devices. DC esettable fuses These fuses protect the internal power supply. If the fuses are tripped they are easily reset by pressing the small buttons on the fuses. 4 24V Backup battery charging The A 495 amplifier includes a charging circuit so that a backup battery connected to the amplifiers Input can be trickle charged. The battery charger is connected to the battery internally when the link is fitted to this connector (see Fig 5 for more details). The battery will be charged at approximately 00mA. 5 24VDC IN Battery Backup: Provision has been provided to run the amplifier from a suitably rated 24V battery system in the event of a mains failure. Using appropriately rated cable, connect the battery to the In terminals. Observe correct polarity when connecting. (see Fig 5 for more details) 6 Input 1 This input can be either a balanced X input or dual CA line input with adjustable input sensitivities of 100mV or 1V. The line input dual CA connectors are internally mixed to produce a mono input signal. 7 Input 2 This input is a dual CA line input with adjustable input sensitivities of 100mV or 1V. The line input dual CA connector is internally mixed to produce a mono input signal. 8 DIP Switches These DIP switches set the input sensitivities of inputs 1 & 2, enable the VOX muting and enable the phantom power to the X input (see Fig 6 for more detail). edback Proudly Made In Australia 5

6 A Watt Power Amplifier SPEAKE CONNECTIONS Speakers with a total impedance or 4-16Ω may be connected to the terminals marked 4-16Ω on the rear of the amplifier. Speakers fitted with line transformers (either 70V or 100V) may be connected to the corresponding terminals on the rear of the amplifer. Always ensure the total load of the fitted speakers does not exceed the rated output of the amplifier (ie 500 watts) otherwise damage may result. When fitting speakers with line transformers the impedance of the load cannot be measured using a standard multimeter. An impedance meter is required. Fig lists the impedance at certain loads of speakers fitted with 70V and 100V line transformers. So for a total load of 500 watts using 100V line transformer fitted speakers, the impedance of the speaker load should be 20Ω. i About 70V & 100V Speaker Systems oad 70V 100V Wiring speakers in parallel for 70/100V line: Where several speakers are to be used at one time, on one circuit, it becomes necessary to use speakers fitted with line-matching transformers. This is to overcome the effects of connecting speakers in parallel and cable losses. The amplifier generally has an output voltage of 100 volts (70 volts is typically used in North America, however operation is similar). In this configuration the total wattage load on the amplifier is derived from adding all the line transformer primary tap ratings together. For example, 70 one watt speakers will have a total speaker load of 70 watts. Or alternatively, it is conceivable to connect 100 one watt speakers to a 100 watt, 100 volt line amplifier. Measuring 70/100V Speaker Impedance: To measure amplifier system load, you must use an impedance meter in order to measure the ac resistance of the connected speaker network. Impedance cannot be measured with a standard multimeter, as this measures the dc resistance. Use the Altronics Q 2001 or similar impedance meter. 0.5W 9.4kΩ 20kΩ 0.66W 7.12kΩ 15kΩ 1W 4.7kΩ 10kΩ 1.25W.76kΩ 8kΩ 2W 2.5kΩ 5kΩ 2.5W 1.88kΩ 4kΩ W 1.56kΩ.kΩ 5W 940Ω 2kΩ 7.5W 626Ω 1.kΩ 10W 470Ω 1kΩ 15W 1Ω 666Ω 20W 25Ω 500Ω 0W 156Ω Ω 40W 117Ω 250Ω 60W 78Ω 166Ω 100W 47Ω 100Ω 125W 7Ω 80Ω 250W 19Ω 40Ω 500W 9.4Ω 20Ω Fig AUDIO CONNECTIONS The amplifier has two audio inputs, with input 1 either a balanced X input or dual CA line input which is internally mixed to create a mono signal. Input 2 is a dual CA which is internally mixed to create a mono signal. Both inputs have adjustable input sensitivities of 100mV or 1V set by the DIP switches on the rear of the unit. A music input on the front of the amplifier is also provided for connection of portable devices. This input when connected, over-rides the rear input 2 audio source and is adjusted via the volume 2 level control. A VOX function is also included which when enabled will allow input 1 to mute input 2. Fig 4 shows a typical install where the A 495 has a balanced microphone connected to input 1 and a level source connected to input 2. If DIP switch 2 is set to ON, the microphone will VOX mute the CD player connected to input 2. Speakers fitted with 100V line transformers. CAUTION ISK OF EECTIC SHOCK OPEN BY QUAIFIED PESONNE ONY! 20V 50Hz (Fuse 10A M205) Made in Australia by Altronic Distributors Pty td OUTPUTS 100V 70V 4-16Ω DIP Switch Settings SW Item On Off Input 1 Sensitivity 1V 0.1V On Off Phantom Power Mic On Off Input 2 Sensitivity 1V 0.1V 1 2 VOX Enable 4 OUT (1A Max) ESETTABE FUSE 20 AMP ESETTABE FUSE 20 AMP INK TO CHAGE BACKUP BATTEY INPUT Input 1 Balanced Mic Input 2 DIP Switches _ 1 Shield 2 Hot Cold Balanced Mic Wiring EDBACK CD Fig 4 6 edback Proudly Made In Australia

7 1 2 4 A Watt Power Amplifier POWE SUPPY The amplifier operates on 20V AC or primarily for battery backup operation. Ensure power is switched OFF at the front panel before connecting either mains power to the IEC socket or to the screw terminal input. As high currents may be drawn when operating from a supply confirm the capacity of the DC power supply used. OUTPUT A constant 24V output terminal has been provided to power ancilliary 24V devices. The output has a maximum current draw of 1 amp. If more than 1 amp is drawn from the output, internal polyswitches will disconnect the output. These will reset once the current draw is reduced. 24V BACKUP BATTEY CHAGING The A 495 amplifier includes a charging circuit so that a backup battery connected to the amplifiers Input can be trickle charged. The battery charger is connected to the battery internally when the link is fitted to the charging link connector (see Fig 5 for more details). The battery will be charged at approximately 00mA. Speakers fitted with 100V line transformers. A 495 AMPIFIE CAUTION ISK OF EECTIC SHOCK OPEN BY QUAIFIED PESONNE ONY! 20V 50Hz (Fuse 10A M205) Made in Australia by Altronic Distributors Pty td OUTPUTS 100V 70V 4-16Ω OUT (1A Max) DIP Switch Settings Item On SW Off 1 Input 1 Sensitivity 1V 0.1V 2 VOX Enable On Off Phantom Power Mic On Off 4 Input 2 Sensitivity 1V 0.1V ESETTABE ESETTABE FUSE 20 AMP FUSE 20 AMP INK TO CHAGE BACKUP BATTEY INPUT Input 1 Balanced Mic Input 2 DIP Switches _ 1 Shield 2 Hot Cold 2 1 Balanced Mic Wiring INK THESE TEMINAS TO CHAGE BACKUP BATTEY - Fig 5 DIP Switch settings The A 495 amplifier has a set of options which are enabled via the DIP switches 1-4. See Fig 6. DIP 1 sets the input level sensitivity for input 1 (either the balanced pin X or Dual CA s). DIP 2 enables the VOX muting. When the VOX is active input 1 will mute input 2. DIP enables the phantom power to the X connector on input 1. DIP 4 sets the input level sensitivity for input 2. DIP Switch Settings SW Item On Off 1 Input 1 Sensitivity 1V 0.1V 2 VOX Enable On Off Phantom Power Mic On Off 4 Input 2 Sensitivity 1V 0.1V Fig 6 edback Proudly Made In Australia 7

8 A Watt Power Amplifier TOUBE SHOOTING If the EDBACK Phase 4 amplifier fails to deliver the rated performance, check the following: No Power, No ights Make sure amplifier power switch is on. Make sure mains power switch is on at the wall. Check the mains and DC fuse. eplace with only the correct type and rating. Over rated fuses will invalidate warranty. Distorted Output Check that the speaker type is correct for the output that you are using (ie. 4-16Ω, 70V or 100V line). Check for any short circuits on the speaker line. Very ow Output Volume Make sure that the input is the correct level (check for shorted connectors). Check for any short circuits on the speaker line. Check if signal ED on the front panel is lit to indicate there is signal. If it is not lit there is no signal present. Continually Blows Fuses Make sure that the speaker line is not shorted. Check speaker types, ratings and if on correct output. Amplifier Keeps on Cutting In & Out Make sure that there is adequate ventilation around the amplifier. Check the vent slots on the front,top and sides are not covered or blocked and the fan on the rear is functioning correctly. Check also speaker types, ratings and for any short circuits on the speaker line. Backup Battery Not Charging Make sure the link is fitted to the charging link connector No Output From Make sure the Out connector is wired correctly. SPECIFICATIONS POWE OUTPUTS A 495: watts MS Distortion:...< 1kHz Output line:...70v, 100V or 4-16Ω FEQUENCY ESPONSE Mic input:...50hz - 12kHz, -db inputs:...50hz - 15kHz, -db SENSITIVITY Mic inputs:...100mv or 1V inputs:...100mv or 1V SIGNA TO NOISE ATIO Mic inputs:...> 75dB below rated output inputs:...> 81dB below rated output OUTPUT CONNECTOS Speakers:...Screw terminals INPUT CONNECTOS Inputs:... pin X balanced or 2 x CA power:...screw terminals 240V AC power:...iec power connector CONTOS Mic inputs:...volume inputs:...volume 100Hz 10kHz Power:...On/off switch Indicators:...Power, signal present, output peak limiting, overtemp,current limit, shutdown, VOX active,, Mains Power Supply:...240V AC or FUSE POTECTION A 495:...10A AC, 20A DC DIMENSIONS... 48W x 410D x 88H *Specifications subject to change without notice 8 edback Proudly Made In Australia