Film Capacitors. Metallized Polyester Film Capacitors (MKT) Date: August 2004

Transcription

1 Film Capacitors Metallized Polyester Film Capacitors (MKT) Series/Type: B B32564 Date: August 2004 EPCOS AG Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited.

2 Metallized polyester film capacitors (MKT) B B32564 Typical applications SMPS, converter Electronic ballasts Compact fluorescent lamps (CFL) Dimensional drawing Climatic Max. operating temperature: 125 C Climatic category (IEC ): 55/125/56 Features Special dimensions available on request High pulse strength Construction Dielectric: polyethylene terephthalate (polyester, PET) Stacked-film technology Uncoated Terminals Parallel wire leads, lead-free tinned Special lead lengths available on request Marking Rated capacitance (coded), rated DC voltage Dimensions in mm Lead spacing ±0.4 Lead diameter d 1 Type B B B32562J 0.8 B32562H B B32564 Delivery mode Bulk (untaped) Taped (Ammo pack or reel) for lead spacing 15.0 mm. For notes on taping, refer to chapter "Taping and packing. Notes on mounting When mounting these capacitors, take into account creepage distances and clearances to adjacent live parts. The insulating strength of the cut surfaces to other live parts of the circuit is 1.5 times the capacitors rated DC voltage, but is always at least 300 VDC. Capacitors with 7.5 mm lead spacing are only suitable for use with single-clad printed circuit boards. Page 2 of 22

3 B B32564 Overview of available types Lead spacing 7.5 mm 10.0 mm 15.0 mm Type B32560 B32561 B32562 Page V R (VDC) V rms (VAC) C R (µf) Page 3 of 22

4 B B32564 Overview of available types Lead spacing 22.5 mm 27.5 mm Type B32563 B32564 Page V R (VDC) V rms (VAC) C R (µf) Page 4 of 22

5 B32560 Ordering codes and packing units (lead spacing 7.5 mm) V R VDC V rms f 60 Hz VAC C R µf Max. dimensions w h l mm Ordering code (composition see below) Ammo pack Reel Untaped B32560J0105+*** B32560J0155+*** B32560J0225+*** B32560J B32560J B32560J1224+*** B32560J1334+*** B32560J1474+*** B32560J1684+*** B32560J1105+*** B32560J1155+*** B32560J B32560J B32560J3473+*** B32560J3683+*** B32560J3104+*** B32560J3154+*** B32560J3224+*** B32560J3334+*** B32560J B32560J Further E series and intermediate capacitance values on request. Special dimensions available on request. For corresponding design rules, refer to chapter "General technical information", Section Composition of ordering code + = Capacitance tolerance code: *** = Packaging code: M = ±20% K = ±10% J = ±5% 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 5 1 mm) Page 5 of 22

6 B32560 Ordering codes and packing units (lead spacing 7.5 mm) V R VDC V rms f 60 Hz VAC C R µf Max. dimensions w h l mm Ordering code (composition see below) Ammo pack Reel Untaped B32560J6102+*** B32560J6152+*** B32560J6222+*** B32560J6332+*** B32560J6472+*** B32560J6682+*** B32560J6103+*** B32560J6153+*** B32560J6223+*** B32560J6333+*** B32560J6473+*** B32560J6683+*** B32560J6104+*** B32560J6154+*** B32560J B32560J8102+*** B32560J8152+*** B32560J8222+*** B32560J8332+*** B32560J8472+*** B32560J8682+*** B32560J8103+*** B32560J B32560J B32560J9222+*** B32560J9332+*** B32560J9472+*** Further E series and intermediate capacitance values on request. Special dimensions available on request. For corresponding design rules, refer to chapter "General technical information", Section Composition of ordering code + = Capacitance tolerance code: *** = Packaging code: M = ±20% K = ±10% J = ±5% 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 5 1 mm) Page 6 of 22

7 B32561 Ordering codes and packing units (lead spacing 10 mm) V R VDC V rms f 60 Hz VAC C R µf Max. dimensions w h l mm Ordering code (composition see below) Ammo pack Reel Untaped B32561J0105+*** B32561J0155+*** B32561J0225+*** B32561J B32561J B32561J B32561J1684+*** B32561J1105+*** B32561J1155+*** B32561J B32561J B32561J3104+*** B32561J3154+*** B32561J3224+*** B32561J3334+*** B32561J3474+*** B32561J B32561J B32561J6333+*** B32561J6473+*** B32561J6683+*** B32561J6104+*** B32561J6154+*** B32561J6224+*** B32561J B32561J Further E series and intermediate capacitance values on request. Special dimensions available on request. For corresponding design rules, refer to chapter "General technical information", Section Composition of ordering code + = Capacitance tolerance code: *** = Packaging code: M = ±20% K = ±10% J = ±5% 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 5 1 mm) Page 7 of 22

8 B32561 Ordering codes and packing units (lead spacing 10 mm) V R VDC V rms f 60 Hz VAC C R µf Max. dimensions w h l mm Ordering code (composition see below) Ammo pack Reel Untaped B32561J8103+*** B32561J8153+*** B32561J8223+*** B32561J8333+*** B32561J8473+*** B32561J B32561J B32561J Further E series and intermediate capacitance values on request. Special dimensions available on request. For corresponding design rules, refer to chapter "General technical information", Section Composition of ordering code + = Capacitance tolerance code: *** = Packaging code: M = ±20% K = ±10% J = ±5% 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 5 1 mm) Page 8 of 22

9 B32562 Ordering codes and packing units (lead spacing 15 mm) V R VDC V rms f 60 Hz VAC C R µf Max. dimensions w h l mm Ordering code (composition see below) Ammo pack Reel B32562J1225+*** B32562J1335+*** B32562H1475+*** B32562H1685+*** B32562H B32562J3474+*** B32562J3684+*** B32562J3105+*** B32562H3155+*** B32562H B32562H B32562J6224+*** B32562J6334+*** B32562J6474+*** B32562H6684+*** B32562H B32562H B32562H B32562H B32562H Untaped Further E series and intermediate capacitance values on request. Special dimensions available on request. For corresponding design rules, refer to chapter "General technical information", Section Composition of ordering code + = Capacitance tolerance code: *** = Packaging code: M = ±20% K = ±10% J = ±5% 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 5 1 mm) Page 9 of 22

10 B32563 Ordering codes and packing units (lead spacing 22.5 mm) V R VDC V rms f 60 Hz VAC C R µf Max. dimensions w h l mm Ordering code (composition see below) Untaped B32563J B32563J B32563J B32563J B32563J B32563J B32563J B32563J B32563J B32563J Further E series and intermediate capacitance values on request. Special dimensions available on request. For corresponding design rules, refer to chapter "General technical information", Section Composition of ordering code + = Capacitance tolerance code: M = ±20% K = ±10% J = ±5% Packaging code: 000 = Untaped (lead length 5 1 mm) Page 10 of 22

11 B32564 Ordering codes and packing units (lead spacing 27.5 mm) V R VDC V rms f 60 Hz VAC C R µf Max. dimensions w h l mm Ordering code (composition see below) Untaped B32564J B32564J B32564J B32564J B32564J B32564J B32564J B32564J B32564J B32564J B32564J B32564J B32564T6475K B32564T6685K Further E series and intermediate capacitance values on request. Special dimensions available on request. For corresponding design rules, refer to chapter "General technical information", Section The technical data given on the next pages do not apply to 420 V series. Please contact your nearest EPCOS representative if you need further information. Composition of ordering code + = Capacitance tolerance code: M = ±20% K = ±10% J = ±5% Packaging code: 000 = Untaped (lead length 5 1 mm) Page 11 of 22

12 B B32564 Technical data Operating temperature range Max. operating temperature T op,max 125 C Upper category temperature T max +125 C Lower category temperature T min 55 C Rated temperature T R +85 C Dissipation factor tan δ (in 10-3 ) at C R 0.1 µf 0.1 µf < C R 1 µf C R > 1 µf at 20 C 1 khz (upper limit values) 10 khz khz 30 Insulation resistance R ins V R C R 0.33 µf C R > 0.33 µf or time constant τ = C R R ins 100 VDC 3750 MΩ 1250 s at 20 C, rel. humidity 65% 250 VDC 7500 MΩ 2500 s (minimum as-delivered values) DC test voltage 1.4 V R, 2 s Category voltage V C T A ( C) DC voltage derating AC voltage derating (continuous operation with V DC T A 85 V C = V R V C,rms = V rms or V AC at f 60 Hz) 85<T A 125 V C = V R (165 T A )/80 V C,rms =V rms (165 T A )/80 Operating voltage V op for T A ( C) DC voltage (max. hours) AC voltage (max. hours) short operating periods T A 100 V op = 1.25 V C (2000 h) V op = 1.0 V C,rms (2000 h) (V DC or V AC at f 60 Hz) 100<T A 125 V op = 1.25 V C (1000 h) V op = 1.0 V C,rms (1000 h) Damp heat test 56 days 1) /40 C/93% relative humidity Limit values after damp Capacitance change C/C 5% heat test Dissipation factor change tan δ (at 1 khz) (at 10 khz) Insulation resistance R ins 50% of minimum or time constant τ = C R R ins as-delivered values Reliability: Failure rate λ 2 fit ( /h) at 0.5 V R, 40 C Service life t SL h at 1.0 V R, 40 C For conversion to other operating conditions and temperatures, refer to chapter "Quality assurance". Failure criteria: Total failure Short circuit or open circuit Failure due to variation Capacitance change C/C > 10% of parameters Dissipation factor tan δ > 2 upper limit value Insulation resistance R ins < 150 MΩ (C R 0.33 µf) or time constant τ = C R R ins < 50 s (C R > 0.33 µf) 1) Test criteria must be met after exposure to damp heat for 21 days Page 12 of 22

13 B B32564 Pulse handling capability "dv/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/µs. "k 0 " represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V 2 /µs. Note: The values of dv/dt and k 0 provided below must not be exceeded in order to avoid damaging the capacitor. dv/dt values Lead spacing 7.5 mm 10 mm 15 mm 22.5 mm 27.5 mm V R V rms VDC VAC dv/dt in V/µs k 0 values Lead spacing 7.5 mm 10 mm 15 mm 22.5 mm 27.5 mm V R V rms VDC VAC k 0 in V 2 /µs Page 13 of 22

14 B B32564 Impedance Z versus frequency f (typical values) Page 14 of 22

15 B32560 Permissible AC voltage V rms versus frequency f (for sinusoidal waveforms, T A 55 C) For T A >55 C, please refer to "General technical information", section Lead spacing 7.5 mm 63 VDC/40 VAC 100 VDC/63 VAC 250 VDC/160 VAC 400 VDC/200 VAC Page 15 of 22

16 B32560 Permissible AC voltage V rms versus frequency f (for sinusoidal waveforms, T A 55 C) For T A >55 C, please refer to "General technical information", section Lead spacing 7.5 mm 630 VDC/400 VAC 1000 VDC/500 VAC Page 16 of 22

17 B32561 Permissible AC voltage V rms versus frequency f (for sinusoidal waveforms, T A 55 C) For T A >55 C, please refer to "General technical information", section Lead spacing 10 mm 63 VDC/40 VAC 100 VDC/63 VAC 250 VDC/160 VAC 400 VDC/200 VAC Page 17 of 22

18 B32561 Permissible AC voltage V rms versus frequency f (for sinusoidal waveforms, T A 55 C) For T A >55 C, please refer to "General technical information", section Lead spacing 10 mm 630 VDC/350 VAC Page 18 of 22

19 B32562 Permissible AC voltage V rms versus frequency f (for sinusoidal waveforms, T A 55 C) For T A >55 C, please refer to "General technical information", section Lead spacing 15 mm 100 VDC/63 VAC 250 VDC/160 VAC 400 VDC/200 VAC 630 VDC/350 VAC Page 19 of 22

20 B32563 Permissible AC voltage V rms versus frequency f (for sinusoidal waveforms, T A 55 C) For T A >55 C, please refer to "General technical information", section Lead spacing 22.5 mm 100 VDC/63 VAC 250 VDC/160 VAC 400 VDC/200 VAC Page 20 of 22

21 B32564 Permissible AC voltage V rms versus frequency f (for sinusoidal waveforms, T A 55 C) For T A >55 C, please refer to "General technical information", section Lead spacing 27.5 mm 100 VDC/63 VAC 250 VDC/160 VAC 400 VDC/200 VAC 420 VDC/200 VAC Page 21 of 22

22 Important Notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of passive electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of a passive electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of a passive electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous ). Useful information on this will be found in our Material Data Sheets on the Internet ( Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the General Terms of Delivery for Products and Services in the Electrical Industry published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, CeraDiode, CSSP, PhaseCap, PhaseMod, SilverCap, SIFI, SIMID, SIKOREL, SIOV, SIP5D, SIP5K, TOPcap, UltraCap, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at Page 22 of 22