LSI/CSI LS7211N-7212N PROGRAMMABLE DIGITAL DELAY TIMER

Size: px
Start display at page:

Download "LSI/CSI LS7211N-7212N PROGRAMMABLE DIGITAL DELAY TIMER"

Transcription

1 LSI/CSI LSN-N UL LSI Computer Systems, Inc. Walt Whitman Road, Melville, NY (6) -000 FX (6) PROGRMMLE DIGITL DELY TIMER FETURES: -bit programmable delay from microseconds to days On chip oscillator (RC or Crystal) or external clock time base Selectable prescaler for real time delay generation based on 0Hz/60Hz time base or,6hz watch crystal Four operating modes Reset input for delay abort Low quiescent and operating current Direct relay drive +V to +V operation ( - VSS) LSN, LSN (DIP); LSN-S, LSN-S (SOIC) - See Figure - DESCRIPTION: The LSN and LSN are CMOS integrated circuits for generating digitally programmable delays. The delay is controlled by binary weighted inputs, W0 - W, in conjunction with an applied clock or oscillator frequency. The programmed time delay manifests itself in the Delay Output () as a function of the Operating Mode selected by the Mode Select inputs and : One-Shot, Delayed Operate, Delayed Release or Dual Delay. The time delay is initiated by a transition of the Trigger Input (). I/O DESCRIPTION: MODE SELECT Inputs & (Pins & ) The operating modes are selected by Inputs and according to Table TLE. MODE SELECTION MODE 0 0 One-Shot (OS) 0 Delayed Operate (DO) 0 Delayed Release (DR) Dual Delay (DD) Each input has an internal pull-up resistor of about 00kΩ. One-Shot Mode (OS) positive transition at the input causes to switch low without delay and starts the delay timer. t the end of the programmed delay timeout, switches high. If a delay timeout is in progress when a positive transition occurs at the input, the delay timer will be restarted. negative transition at the input has no effect. Delayed Operate Mode (DO) positive transition at the input starts the delay timer. t the end of the delay timeout, switches low. negative transition at the input causes to switch high without delay. is high when is low. N-00- () RC/ RCS/CLKS PSCLS VSS (-V) () XTLI/ XTLO PSCLS VSS (-V) PIN SSIGNMENT - TOP VIEW 6 6 LSI 9 0 LSI Feb 0 Delayed Release Mode (DR) negative transition at the input starts the delay timer. t the end of the delay timeout, switches high. postive transition at the input causes to switch low without delay. is low when is high. Dual Delay Mode (DD) positive or negative transition at the input starts the delay timer. t the end of the delay timeout, switches to the logic state which is the inverse of the input. If a delay timeout is in progress when a transition occurs at the input, the delay timer is restarted. LSN LSN FIGURE W0 W W W W W W6 W W0 W W W W W W6 W

2 GER Input (, Pin ) transition at the input causes to switch with or without delay, depending on the selected mode. The input to transition relation is always opposite in polarity, with the exception of One-Shot mode. (See Mode definitions above.) input has an internal pull-down resistor of about 00kΩ and is buffered by a Schmitt trigger to provide input hysteresis. LSN TIME SE Input (RC/, Pin ) For LSN, the basic timing signal is applied at the RC/ input. The clock can be provided from either an external source or generated by an internal oscillator by connecting an R-C network to this input. The frequency of oscillation is given by ƒ /RC. Chip-tochip oscillation tolerance is ± % for a fixed value of RC. The minimum resistance, R MIN = 000Ω, = + V = 00Ω, = +0V = 600Ω, = +V The external clock mode is selected by applying a logic low to the RCS/CLKS input (Pin ); the internal oscillator mode is selected by applying a high level to the RCS/CLKS input. LSN TIME SE Input (XTLI/, Pin ) For LSN, the basic timing clock is applied to the XLTI/ input from either an external clock source or generated by an internal crystal oscillator by connecting a crystal between XTLI/ input and the XTLO output (Pin ). LSN TIME SE SELECT Input (RCS/CLKS, Pin ) For LSN, the external clock operation at Pin is selected by applying a logic low to the RCS/CLKS input. The internal oscillator option with RC timer at Pin is selected by applying a logic high at the RCS/CLKS input. RCS/CLKS input has an internal pull-down resistor of about 00kΩ. LSN TIME SE Output (XTLO, Pin ) For LSN, when a crystal is used for generating the time base oscillation, the crystal is connected between XTLI/ and XTLO pins. PRESCLER SELECT Input (PSCLS, Pin 6) The PSCLS input is a -state input, which selects one of three prescale factors according to Table. TIMER Input (, Pin ) When input switches high, any timeout in progress is aborted and switches high without delay. With RE- SET high, remains high. When switches low with low in any mode, remains high. When RE- SET switches low with high in Delayed Operate and Dual Delay modes, the delay timer is started and switches low at the end of the delay timeout. When RE- SET switches low with high in Delayed Release mode, switches low without delay. When switches low with high in One-Shot mode, remains high. input has an internal pull-down resistor of about 00kΩ, and is buffered by a Schmitt Trigger to provide input hysteresis. VSS (-V, Pin ) Supply voltage negative terminal or GND. DELY Output (, Pin 9) Except in One-Shot mode, switches with or without delay (depending on mode) in inverse relation to the logic level of the input. In One-Shot mode, a timed low level is produced at, in response to a positive transition of the input. WEIGHTING IT Inputs (W to W0, Pins 0 - ) Inputs W0 through W are binary weighted delay bits used to program the delay according to the following relations: One-Shot Mode: Pulse width = SW ƒ ll other Modes: Delay = SW + 0. ƒ Where: S = Prescale factor (See Table ) ƒ = Time base frequency at Pin W = W0 + W +... W The weighting factor W is calculated by substituting in the equation above for W, the weighted values for all the W inputs that are at logic high. The weighted values for the W inputs are shown in Table. Each W input has an internal pull-down resistor of about 00kΩ. TLE. PRESCLE FCTOR SELECTION TLE. IT WEIGHTS PSCLS Input S (Prescale Factor ) Logic Level LSN LSN Float VSS,000,6,600,6x60 Using prescale factors of 000 and 600, delays in units of minutes can be produced from 0Hz and 60Hz line sources. Prescale factors of,6 and,6 x 60 can be used to generate accurate delays in units of seconds and minutes, respectively, from a khz watch crystal. N ITS VLUE W0 W W W W 6 W W6 6 W (, Pin ) Supply voltage positive terminal.

3 SOLUTE MXIMUM RTINGS: (ll voltages referenced to VSS) SYMOL VLUE UNIT DC Supply Voltage +9 V Voltage (ny Pin) VIN VSS - 0. to + 0. V Operating Temperature T -0 to + C Storage Temperature TSTG -6 to +0 C ELECTRICL CHRCTERISTICS (Voltages referenced to Vss) Characteristic SYMOL -0 C + C + C Unit Condition Min Max Min Max Min Max Supply Voltage V µ Supply Current IDD µ with the clock off and µ all inputs floating. Input Voltages: V Reset, Trigger Low VTL V V V Reset, Trigger High VTH V V V Reset, Trigger Hysteresis V V V ll other inputs, Low VIL V V V ll other inputs, High VIH V V Input Currents: µ PSCLS Low IPL µ Input at VSS µ µ PSCLS High IPH µ Input at µ µ, Low IML µ Input at VSS µ, High IMH n Input at ll other inputs, Low IIL n Input at VSS µ ll other inputs, High IIH µ Input at µ Output Current: m Sink IOSNK m Vo = +0.V m m Source IOSRC m Vo = - 0.V m N-0009-

4 ELECTRICL CHRCTERISTICS (Voltages referenced to Vss) (Con t) Characteristic SYMOL Unit Condition Min Max Min Max Min Max Switching Characteristics (See Fig. ) MHz RC Oscillator Frequency fosc MHz MHz MHz For prescale External Clock or fext MHz factor S = 6 Crystal Oscillator MHz or 6 x 60 Frequency MHz S = or 000 fext MHz or MHz Set-Up Time t ns -, Set-Up Time t ns - W0 - W Set-Up Time t ns ns Clock to Out Delay t ns CL = 0pF ns 00k MODE REG 00k EDGE DETECT LTCH CONTROL LOGIC UF 9 00k /RC/XTLI 00k LTCH/TIMER 0- W-W0 00k () OSC MUX XTLO (LSN) PRESCLER RCS/CLKS (LSN) 00k PSCLS 6 M M -STTE DECODER -V (Gnd) VSS FIGURE. LSN / LSN LOCK DIGRM N-00-

5 t0 Clock t t, W0-W t t = 0, =, Delayed Operate Programmed Delay t Immediate Release Note. input is clocked in by the negative edge of external clock. Note. Inputs, and W0 - W are sampled only at a input transition and ignored at all other times. Note. is switched by the positive edge of the external clock. FIGURE. INPUT/PUT TIMING (OS) C F (DO) (DR) D (DD) E G H. Turn-on delay in DO and DD modes; Pulse-width in OS mode.. Turn-off delay in DR and DD modes. C. Pulse-width extended by re-trigger in OS mode. No effect in DO and DD modes because switches back low before turn-on delay has timed out. D. Turn-off delay in DR mode. E. Turn-on delay in DO and DD modes; pulse-width in OS mode. F. No effect in DO, DR and DD modes because of s switching back to opposite levels. G. Time-outs aborted and forces high by. H. fter the removal of, switches to the inverse polarity of immediately (DR) or after the timeout (DO, DD). No effect in OS. FIGURE. MODE ILLUSTRTION WITH, ND N

6 RCS/CLKS pf 0k CRYSTL 0M XTLO LSN XTLI LSN 0k ƒ 0.µF RC LSN pf LSN FIGURE 6. MULTI-TIMER WITH SINGLE CRYSTL TIME-SE V SS V DD ƒ = x 0 x 0. x 0 = khz 0VC M LSN FIGURE. RC- Oscillator Connection 00pF V SS FIGURE. DRIVING INPUT FROM THE C LINE * * 0-, W0-W, LSN * * 0-, W0-W, LSN GER ƒ 9 9 Vss Vss * Connect for desired delay and mode FIGURE. DELY EXTENSION Y CSCDING N

7 GER IN pf ƒ pf 0k S 0M 6 XTLI XTLO PSCLS W0 W W W W W W6 W 6 0 s/m s/m s/m s/m 6s/6m s/m 6s/6m s/m Vss LSN s = seconds m = minutes PUT 9 NOTE : Crystal Frequency, ƒ =,6Hz Switch: S low: Delay increment = s; Maximum Delay = s S high: Delay increment = m; Maximum Delay = m FIGURE 9. PROGRMMLE CCURTE REL-TIME DELY GENERTION The information included herein is believed to be accurate and reliable. However, LSI Computer Systems, Inc. assumes no responsibilities for inaccuracies, nor for any infringements of patent rights of others which may result from its use. N-0606-

8 V DD W0 W 6 ƒi LSN W W W W ƒo 9 Vss W6 W 0 CSE. MODE = DO or DR; PRESCLE FCTOR, S = In this setup a frequency division of the input clock, ƒi by a factor of to, in increments of can be obtained according to the equation: ƒo = ƒi where W (weighting factor) = 0 to W + The ƒo pulse width is non-symmetrical (non-0% duty -cycle) CSE. MODE = DD; PRESCLE FCTOR, S = In this setup a frequency division of the input clock, ƒi by a factor of to, in increments of can be obtained according to the equation: ƒi ƒo = where W (weighting factor) = 0 to (W + ) The ƒo pulse widths are symmetrical with 0% duty -cycle EXMPLES OF CSE and CSE FREQUENCY DIVISIONS WITH W = ƒi ƒo Case, Mode = DO; ƒo Case, Mode = DD; 6 N FIGURE 0. PROGRMMLE FREQUENCY DIVIDER

LSI/CSI LS7215 LS7216 PROGRAMMABLE DIGITAL DELAY TIMER

LSI/CSI LS7215 LS7216 PROGRAMMABLE DIGITAL DELAY TIMER LSI/CSI UL 00 LSI Computer Systems, Inc. Walt Whitman Road, Melville, NY (6) -000 FX (6) -00 PROGRMMLE DIGITL DELY TIMER FETURES: Programmable delay from microseconds to days Programmable delay controlled

More information

LSI/CSI LS7213R PROGRAMMABLE DIGITAL DELAY TIMER

LSI/CSI LS7213R PROGRAMMABLE DIGITAL DELAY TIMER LSI/CSI LSR UL 00 PROGRMMLE DIGITL DELY TIMER FETURES: Eight timing ranges Four modes controlled on-chip oscillator Power-On-Reset (POR) Reset input for delay abort Complementary outputs Delay-in-Progress

More information

LSI/CSI LS7560N LS7561N BRUSHLESS DC MOTOR CONTROLLER

LSI/CSI LS7560N LS7561N BRUSHLESS DC MOTOR CONTROLLER LSI/CSI LS7560N LS7561N LSI Computer Systems, Inc. 15 Walt Whitman Road, Melville, NY 747 (631) 71-0400 FAX (631) 71-0405 UL A3800 BRUSHLESS DC MOTOR CONTROLLER April 01 FEATURES Open loop motor control

More information

LSI/CSI LS7290 STEPPER MOTOR CONTROLLER. LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631)

LSI/CSI LS7290 STEPPER MOTOR CONTROLLER. LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) LSI/CSI UL A800 FEATURES: LSI Computer Systems, Inc. 1 Walt Whitman Road, Melville, NY 114 (1) 1-0400 FAX (1) 1-040 STEPPER MOTOR CONTROLLER Controls Bipolar and Unipolar Motors Cost-effective replacement

More information

LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631)

LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) LSI/CSI UL A3800 LSI Computer Systems, Inc. 235 Walt Whitman Road, Melville, NY 747 (63) 270400 FAX (63) 270405 TOUCH CONTROL STEP DIMMER LIHT SWITCH WITH AUTOMATIC AIN CONTROL (AC) March 2007 FEATURES:

More information

MC14541B. Programmable Timer

MC14541B. Programmable Timer MC44 Programmable Timer The MC44 programmable timer coists of a stage binary counter, an integrated oscillator for use with an external capacitor and two resistors, an automatic power on reset circuit,

More information

LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) PIR SENSOR INTERFACE DIFF. AMP.

LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) PIR SENSOR INTERFACE DIFF. AMP. LSI/CSI LS6522 UL LSI Computer Systems, Inc. 1235 Walt Whitman Road, Melville, NY 11747 (631) 2710400 FAX (631) 2710405 A3800 PIR SENSOR INTERFACE February 2014 FEATURES: Low Quiescent Current Direct Interface

More information

LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) PIR SENSOR INTERFACE

LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) PIR SENSOR INTERFACE LSI/CSI LS6N LS6 LS6 UL LSI Computer Systems, Inc. Walt Whitman Road, Melville, NY 77 (6) 7000 FAX (6) 700 A800 SENSOR INTERFACE September 009 FEATURES: Direct Interface with Sensor TwoStage Differential

More information

LSI/CSI LS7232NT PROXIMITY/TOUCH CONTROL HALOGEN LAMP DIMMER

LSI/CSI LS7232NT PROXIMITY/TOUCH CONTROL HALOGEN LAMP DIMMER LSI/CSI LS7232NT UL LSI Computer Systems, Inc. 1235 Walt Whitman Road, Melville, NY 11747 (631) 271-0400 FAX (631) 271-0405 A00 PROXIMITY/TOUCH CONTROL HALOGEN L DIMMER FEATURES: Control of incandescent

More information

ICS Glitch-Free Clock Multiplexer

ICS Glitch-Free Clock Multiplexer Description The ICS580-01 is a clock multiplexer (mux) designed to switch between 2 clock sources with no glitches or short pulses. The operation of the mux is controlled by an input pin but the part can

More information

LSI/CSI LS8292 LS8293. PRELIMINARY MICRO-STEPPING MOTOR CONTROLLER June 2013

LSI/CSI LS8292 LS8293. PRELIMINARY MICRO-STEPPING MOTOR CONTROLLER June 2013 LSI/CSI LS8292 LS8293 LSI Computer Systems, Inc. 1235 Walt Whitman Road, Melville, NY 11747 (631) 271-0400 FAX (631) 271-0405 PRELIMINARY MICRO-STEPPING MOTOR CONTROLLER June 2013 FEATURES: DESCRIPTION:

More information

LSI/CSI LS6506R LS6507R PIR SENSOR INTERFACE. LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631)

LSI/CSI LS6506R LS6507R PIR SENSOR INTERFACE. LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) 6506R0602091 LSI/CSI UL A3800 LS6506R LS6507R LSI Computer Systems, Inc. 1235 Walt Whitman Road, Melville, NY 11747 (631) 2710400 FAX (631) 2710405 FEATURES: Latching relay drive (LS6506R) LS6506R is suitable

More information

LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) DECADE PREDETERMINING UP/DOWN COUNTER

LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) DECADE PREDETERMINING UP/DOWN COUNTER LSI/CSI UL A3800 LSI Computer Systems, Inc. 1235 Walt Whitman Road, Melville, NY 11747 (631) 271-0400 FAX (631) 271-0405 6 DECADE PREDETERMINING UP/DOWN COUNTER FEATURES: +4.75V to +15V ( - VDD) Preset,

More information

LSI/CSI LS8397 STEPPER MOTOR CONTROLLER. LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631)

LSI/CSI LS8397 STEPPER MOTOR CONTROLLER. LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) LSI/SI LS39 UL LSI omputer Systems, Inc. Walt Whitman Road, Melville, NY 4 (3) -0400 FAX (3) -040 A300 PER MOTOR ONTROLLER April 009 FEATURES: ontrols Bipolar and Unipolar Motors L9 operation with added

More information

DATASHEET CD4060BMS. Pinout. Features. Functional Diagram. Oscillator Features. Applications. Description

DATASHEET CD4060BMS. Pinout. Features. Functional Diagram. Oscillator Features. Applications. Description DATASHEET CDBMS CMOS 1 Stage Ripple-Carry Binary Counter/Divider and Oscillator FN3317 Rev. Features Pinout High Voltage Type (V Rating) Common Reset 1MHz Clock Rate at 15V Fully Static Operation Q1 Q13

More information

LSI/CSI LS8297 LS8297CT STEPPER MOTOR CONTROLLER

LSI/CSI LS8297 LS8297CT STEPPER MOTOR CONTROLLER LSI/CSI LS9 LS9CT UL LSI Computer Systems, Inc. Walt Whitman oad, Melville, NY 4 (3) -0400 FAX (3) -040 A300 PE MOTO CONTOLLE April 009 FEATUES: Controls Bipolar and Unipolar Motors Cost-effective, low

More information

CF5074B VCXO Module IC with Built-in Varicap

CF5074B VCXO Module IC with Built-in Varicap XO Module IC with Built-in Varicap OVERVIEW The CF574B is XO module IC with built-in varicap diodes. The integrated varicap diode BiCMOS process allows the device to be fabricated on a single chip. newly

More information

NJ88C Frequency Synthesiser with non-resettable counters

NJ88C Frequency Synthesiser with non-resettable counters NJ88C Frequency Synthesiser with non-resettable counters DS8 -. The NJ88C is a synthesiser circuit fabricated on the GPS CMOS process and is capable of achieving high sideband attenuation and low noise

More information

Programmable Low Voltage 1:10 LVDS Clock Driver ADN4670

Programmable Low Voltage 1:10 LVDS Clock Driver ADN4670 Data Sheet Programmable Low Voltage 1:10 LVDS Clock Driver FEATURES FUNCTIONAL BLOCK DIAGRAM Low output skew

More information

CD4541BC Programmable Timer

CD4541BC Programmable Timer CD4541BC Programmable Timer General Description The CD4541BC Programmable Timer is designed with a 16-stage binary counter, an integrated oscillator for use with an external capacitor and two resistors,

More information

Preliminary Rev. M Accusilicon AS318-B Series Professional Audiophile Crystal Oscillator

Preliminary Rev. M Accusilicon AS318-B Series Professional Audiophile Crystal Oscillator Accusilicon AS318-B Series Professional Audiophile Crystal Oscillator Features Extremely low close-in phase noise, designed for professional Audiophile & Recording application. Typical -100dBc @ 10Hz at

More information

DATA SHEET. HEF4541B MSI Programmable timer. For a complete data sheet, please also download: INTEGRATED CIRCUITS

DATA SHEET. HEF4541B MSI Programmable timer. For a complete data sheet, please also download: INTEGRATED CIRCUITS INTEGRATED CIRCUITS DATA SHEET For a complete data sheet, please also download: The IC04 LOCMOS HE4000B Logic Family Specifications HEF, HEC The IC04 LOCMOS HE4000B Logic Package Outlines/Information HEF,

More information

Low Power Low Offset Voltage Dual Comparators

Low Power Low Offset Voltage Dual Comparators Low Power Low Offset ltage Dual Comparators Product Description The GS393 consists of two independent precision voltage comparators which were designed specifically to operate from a single power supply

More information

ML4818 Phase Modulation/Soft Switching Controller

ML4818 Phase Modulation/Soft Switching Controller Phase Modulation/Soft Switching Controller www.fairchildsemi.com Features Full bridge phase modulation zero voltage switching circuit with programmable ZV transition times Constant frequency operation

More information

DATASHEET CD4013BMS. Pinout. Features. Functional Diagram. Applications. Description. CMOS Dual D -Type Flip-Flop. FN3080 Rev 0.

DATASHEET CD4013BMS. Pinout. Features. Functional Diagram. Applications. Description. CMOS Dual D -Type Flip-Flop. FN3080 Rev 0. DATASHEET CD013BMS CMOS Dual D -Type Flip-Flop FN300 Rev 0.00 Features High-Voltage Type (0V Rating) Set-Reset Capability Static Flip-Flop Operation - Retains State Indefinitely With Clock Level Either

More information

DATASHEET CD4069UBMS. Features. Pinout. Applications. Functional Diagram. Description. Schematic Diagram. CMOS Hex Inverter

DATASHEET CD4069UBMS. Features. Pinout. Applications. Functional Diagram. Description. Schematic Diagram. CMOS Hex Inverter DATASHEET CD9UBMS CMOS Hex Inverter FN331 Rev. December 199 Features Pinout High Voltage Types (V Rating) Standardized Symmetrical Output Characteristics CD9UBMS TOP VIEW Medium Speed Operation: tphl,

More information

MOS INTEGRATED CIRCUIT

MOS INTEGRATED CIRCUIT DATA SHEET MOS INTEGRATED CIRCUIT µpd6345 8 BIT SERIAL IN/PARALLEL OUT DRIVER The µpd6345 is a monolithic Bi-CMOS integrated Circuit designed to drive LED, Solenoid and Relay. This device consists of an

More information

OBJECTIVE The purpose of this exercise is to design and build a pulse generator.

OBJECTIVE The purpose of this exercise is to design and build a pulse generator. ELEC 4 Experiment 8 Pulse Generators OBJECTIVE The purpose of this exercise is to design and build a pulse generator. EQUIPMENT AND PARTS REQUIRED Protoboard LM555 Timer, AR resistors, rated 5%, /4 W,

More information

M-991 Call Progress Tone Generator

M-991 Call Progress Tone Generator Call Progress Tone Generator Generates standard call progress tones Digital input control Linear (analog) output Power output capable of driving standard line 14-pin DIP and 16-pin SOIC package types Single

More information

LC75857E LC75857W. SANYO Semiconductors DATA SHEET. Preliminary. Overview. Features. CMOS IC 1/3, 1/4 Duty LCD Display Drivers with Key Input Function

LC75857E LC75857W. SANYO Semiconductors DATA SHEET. Preliminary. Overview. Features. CMOS IC 1/3, 1/4 Duty LCD Display Drivers with Key Input Function Ordering number : ENN*798 Preliminary SANYO Semiconductors DATA SHEET LC75857E LC75857W CMOS IC 1/3, 1/4 Duty LCD Display Drivers with Key Input Function Overview The LC75857E and LC75857W are 1/3 duty

More information

MM Stage Oscillator Divider

MM Stage Oscillator Divider MM5369 17 Stage Oscillator Divider General Description The MM5369 is a CMOS integrated circuit with 17 binary divider stages that can be used to generate a precise reference from commonly available high

More information

DATASHEET CD4027BMS. Features. Pinout. Functional Diagram. Applications. Description. CMOS Dual J-KMaster-Slave Flip-Flop. FN3302 Rev 0.

DATASHEET CD4027BMS. Features. Pinout. Functional Diagram. Applications. Description. CMOS Dual J-KMaster-Slave Flip-Flop. FN3302 Rev 0. DATASHEET CD7BMS CMOS Dual J-KMaster-Slave Flip-Flop FN33 Rev. Features Pinout High Voltage Type (V Rating) Set - Reset Capability CD7BMS TOP VIEW Static Flip-Flop Operation - Retains State Indefinitely

More information

DATASHEET CD4098BMS. Description. Features. Applications. Pinout. CMOS Dual Monostable Multivibrator. FN3332 Rev 0.00 Page 1 of 11.

DATASHEET CD4098BMS. Description. Features. Applications. Pinout. CMOS Dual Monostable Multivibrator. FN3332 Rev 0.00 Page 1 of 11. DATASHEET CD9BMS CMOS Dual Monostable Multivibrator Features High Voltage Type (V Rating) Retriggerable/Resettable Capability Trigger and Reset Propagation Delays Independent of RX, CX Triggering from

More information

XR-2207 Voltage-Controlled Oscillator

XR-2207 Voltage-Controlled Oscillator ...the analog plus company TM Voltage-Controlled Oscillator FETURES Excellent Temperature Stability (20ppm/ C) Linear Frequency Sweep djustable Duty Cycle (0.% to.%) Two or Four Level FSK Capability Wide

More information

DATASHEET CD14538BMS. Description. Features. Applications. Functional Diagram. Pinout. CMOS Dual Precision Monostable Multivibrator

DATASHEET CD14538BMS. Description. Features. Applications. Functional Diagram. Pinout. CMOS Dual Precision Monostable Multivibrator DATASHEET CD153BMS CMOS Dual Precision Monostable Multivibrator FN319 Rev. Features High-Voltage Type (V Rating) Retriggerable/Resettable Capability Trigger and Reset Propagation Delays Independent of

More information

DATASHEET 82C284. Features. Description. Part # Information. Pinout. Functional Diagram. Clock Generator and Ready Interface for 80C286 Processors

DATASHEET 82C284. Features. Description. Part # Information. Pinout. Functional Diagram. Clock Generator and Ready Interface for 80C286 Processors OBSOLETE PRODUCT NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc Clock Generator and Ready Interface for 80C286 Processors DATASHEET FN2966 Rev.2.00

More information

HiMARK FS8170. FS GHz Low Power Phase-locked Loop IC. Description. Features. Package and Pin Assignment

HiMARK FS8170. FS GHz Low Power Phase-locked Loop IC. Description. Features. Package and Pin Assignment 2. GHz Low Power Phase-locked Loop IC Princeton Technology Corp. reserves the right to change the product described in this datasheet. ll information contained in this datasheet is subject to change without

More information

78A207 MFR1 Receiver DATA SHEET DESCRIPTION FEATURES OCTOBER 2005

78A207 MFR1 Receiver DATA SHEET DESCRIPTION FEATURES OCTOBER 2005 DESCRIPTION The 78A207 is a single-chip, Multi-Frequency (MF) receiver that can detect all 15 tone-pairs, including ST and KP framing tones. This receiver is intended for use in equal access applications

More information

2.6GHz Bidirectional I 2 C BUS Controlled Synthesiser

2.6GHz Bidirectional I 2 C BUS Controlled Synthesiser SP555.6GHz Bidirectional I C BUS Controlled Synthesiser The SP555 is a single chip frequency synthesiser designed for T tuning systems. Control data is entered in the standard I C BUS format. The device

More information

Embedded Systems. Oscillator and I/O Hardware. Eng. Anis Nazer First Semester

Embedded Systems. Oscillator and I/O Hardware. Eng. Anis Nazer First Semester Embedded Systems Oscillator and I/O Hardware Eng. Anis Nazer First Semester 2016-2017 Oscillator configurations Three possible configurations for Oscillator (a) using a crystal oscillator (b) using an

More information

CARDINAL COMPONENTS. Operating Conditions: Description Min Max Unit

CARDINAL COMPONENTS. Operating Conditions: Description Min Max Unit Standard Package Options Series CPP Part Numbering Example: CPP C 1 L Z - A5 B6 - XXXXXX TS CPP C 1 L Z A5 SERIES CPP OUTPUT C = CMOS T = TTL Specifications: PACKAGE STYLE 1 = Full Size 4 = Half Size 5

More information

SG2525A SG3525A REGULATING PULSE WIDTH MODULATORS

SG2525A SG3525A REGULATING PULSE WIDTH MODULATORS SG2525A SG3525A REGULATING PULSE WIDTH MODULATORS 8 TO 35 V OPERATION 5.1 V REFERENCE TRIMMED TO ± 1 % 100 Hz TO 500 KHz OSCILLATOR RANGE SEPARATE OSCILLATOR SYNC TERMINAL ADJUSTABLE DEADTIME CONTROL INTERNAL

More information

DATASHEET CD4028BMS. Features. Pinout. Functional Diagram. Applications. Description. CMOS BCD-To-Decimal Decoder. FN3303 Rev 0.

DATASHEET CD4028BMS. Features. Pinout. Functional Diagram. Applications. Description. CMOS BCD-To-Decimal Decoder. FN3303 Rev 0. DATASHEET CMOS BCD-To-Decimal Decoder FN Rev. December Features Pinout High Voltage Type (V Rating) BCD-to-Decimal Decoding or Binary-to-Octal Decoding TOP VIEW High Decoded Output Drive Capability Positive

More information

ICS507-01/02 PECL Clock Synthesizer

ICS507-01/02 PECL Clock Synthesizer Description The ICS507-01 and ICS507-02 are inexpensive ways to generate a low jitter 155.52 MHz (or other high speed) differential PECL clock output from a low frequency crystal input. Using Phase-Locked-

More information

LSI/CSI LS BIT MULTI-MODE COUNTER

LSI/CSI LS BIT MULTI-MODE COUNTER LSI/CSI LS766 UL LSI Computer Systems, Inc. 235 Walt Whitman Road, Melville, NY 747 (63) 27-4 FAX (63) 27-45 A38 24-BIT MULTI-MODE COUNTER December 999 FEATURES: Programmable modes are: Up/Down, Binary,

More information

General-Purpose OTP MCU with 14 I/O LInes

General-Purpose OTP MCU with 14 I/O LInes General-Purpose OTP MCU with 14 I/O LInes Product Specification PS004602-0401 PRELIMINARY ZiLOG Worldwide Headquarters 910 E. Hamilton Avenue Campbell, CA 95008 Telephone: 408.558.8500 Fax: 408.558.8300

More information

LC75836WS-T/D. 1/4-Duty General-Purpose LCD Driver

LC75836WS-T/D. 1/4-Duty General-Purpose LCD Driver 1/4-Duty General-Purpose LCD Driver Overview The LC75836WS-T is 1/4-duty general-purpose microprocessor-controlled LCD driver that can be used in applications such as frequency display in products with

More information

Low Power Windowed Watchdog with Reset, Sleep Mode Functions. Features. Applications. Selection Table. Part Number V REF

Low Power Windowed Watchdog with Reset, Sleep Mode Functions. Features. Applications. Selection Table. Part Number V REF EM MICROELECTRONIC - MARIN SA Low Power Windowed Watchdog with Reset, Sleep Mode Functions Description The offers a high level of integration by combining voltage monitoring and software monitoring using

More information

Dual Processor Supervisors with Watchdog ADM13305

Dual Processor Supervisors with Watchdog ADM13305 Dual Processor Supervisors with Watchdog ADM335 FEATURES Dual supervisory circuits Supply voltage range of 2.7 V to 5.5 V Pretrimmed threshold options:.8 V, 2.5 V, 3.3 V, and 5 V Adjustable.6 V voltage

More information

NT7605. Features. General Description

NT7605. Features. General Description PRELIMINARY Single-chip 20CX2L Dot-Matrix LCD Controller / Driver Features! Internal LCD drivers 6 common signal drivers 00 segment signal drivers! Maximum display dimensions 20 characters * 2 lines or

More information

Z86116 CMOS Z8 PN MODULATOR WIRELESS CONTROLLER CUSTOMER PROCUREMENT SPECIFICATION FEATURES GENERAL DESCRIPTION Z86116 CP95WRL0501 PRELIMINARY

Z86116 CMOS Z8 PN MODULATOR WIRELESS CONTROLLER CUSTOMER PROCUREMENT SPECIFICATION FEATURES GENERAL DESCRIPTION Z86116 CP95WRL0501 PRELIMINARY PRELIMINARY CUSTOMER PROCUREMENT SPECIFICATION CMOS Z8 PN MODULATOR WIRELESS CONTROLLER FEATURES ROM RAM* SPEED Part (Kbytes) (Kbytes) (MHz) 1 124 12 * General-Purpose 18-Pin DIP and SOIC Packages 3.0-

More information

TDA7326 AM-FM RADIO FREQUENCY SYNTHESIZER

TDA7326 AM-FM RADIO FREQUENCY SYNTHESIZER AM-FM RADIO FREQUENCY SYNTHESIZER FM INPUT AND PRECOUNTER FOR UP TO 140MHz AM INPUT FOR UP TO 40MHz 6-BIT SWALLOW COUNTER, 8-BIT PRO- GRAMMABLE COUNTER FOR FM AND SW 14-BIT PROGRAMMABLE COUNTER FOR LW

More information

HCF4018B PRESETTABLE DIVIDE-BY-N COUNTER

HCF4018B PRESETTABLE DIVIDE-BY-N COUNTER PRESETTABLE DIVIDE-BY-N COUNTER MEDIUM SPEED OPERATION 10 MHz (Typ.) at V DD - V SS = 10V FULLY STATIC OPERATION STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED UP TO 20V 5V,

More information

MB1503. LOW-POWER PLL FREQUENCY SYNTHESIZER WITH POWER SAVE FUNCTION (1.1GHz) Sept Edition 1.0a DATA SHEET. Features

MB1503. LOW-POWER PLL FREQUENCY SYNTHESIZER WITH POWER SAVE FUNCTION (1.1GHz) Sept Edition 1.0a DATA SHEET. Features Sept. 1995 Edition 1.0a MB1503 DATA SHEET LOW-POWER PLL FREQUENCY SYNTHESIZER WITH POWER SAVE FUNCTION (1.1GHz) The Fujitsu MB1503 is a serial input phase-locked loop (PLL) frequency synthesizer with a

More information

MOSA ELECTRONICS. Features. Description. MS8870 DTMF Receiver

MOSA ELECTRONICS. Features. Description. MS8870 DTMF Receiver Features Complete DTMF receiver Low power consumption Adjustable guard time Central Office Quality CMOS, Single 5V operation Description O rdering Information : 18 PIN DIP PACKAGE The is a complete DTMF

More information

HCF4017B DECADE COUNTER WITH 10 DECODED OUTPUTS

HCF4017B DECADE COUNTER WITH 10 DECODED OUTPUTS DECADE COUNTER WITH 10 DECODED OUTPUTS MEDIUM SPEED OPERATION : 10 MHz (Typ.) at V DD = 10V FULLY STATIC OPERATION STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED UP TO 20V

More information

UNISONIC TECHNOLOGIES CO., LTD CD4541

UNISONIC TECHNOLOGIES CO., LTD CD4541 UNISONIC TECHNOLOGIES CO., LTD CD4541 PROGRAMMABLE TIMER DESCRIPTION The CD4541 programmable timer comprise a 16-stage binary counter, an integrated oscillator for use with an external capacitor and two

More information

FAST CMOS OCTAL BIDIRECTIONAL TRANSCEIVER

FAST CMOS OCTAL BIDIRECTIONAL TRANSCEIVER IDT74FCT2245T/CT FST CMOS OCTL BIDIRECTIONL TRNSCEIVER FST CMOS OCTL BIDIRECTIONL TRNSCEIVER INDUSTRIL TEMPERTURE RNGE IDT74FCT2245T/CT FETURES: and C grades Low input and output leakage 1μ (max.) CMOS

More information

EN: This Datasheet is presented by the m anufacturer. Please v isit our website for pricing and availability at ore.hu.

EN: This Datasheet is presented by the m anufacturer. Please v isit our website for pricing and availability at   ore.hu. EN: This Datasheet is presented by the m anufacturer. Please v isit our website for pricing and availability at www.hest ore.hu. CD49BMS December 199 Features High-Voltage Type (V Rating) Medium Speed

More information

SM5160CM/DM OVERVIEW PINOUT FEATURES PACKAGE DIMENSIONS SERIES LINEUP. Programable PLL Frequency Synthesizer. (Top View)

SM5160CM/DM OVERVIEW PINOUT FEATURES PACKAGE DIMENSIONS SERIES LINEUP. Programable PLL Frequency Synthesizer. (Top View) NIPPON PRECISION CIRCUITS INC. Programable PLL Frequency Synthesizer OVERVIEW PINOUT (Top View) The SM5160CM/DM is a PLL frequency synthesizer IC with programmable input and reference frequency dividers.

More information

CD4028. CMOS BCD-To-Decimal Decoder. Pinout. Features. Functional Diagram. Applications. Description.

CD4028. CMOS BCD-To-Decimal Decoder. Pinout. Features. Functional Diagram. Applications. Description. CD CMOS BCD-To-Decimal Decoder Features Pinout High Voltage Type (V Rating) BCD-to-Decimal Decoding or Binary-to-Octal Decoding TOP VIEW High Decoded Output Drive Capability Positive Logic Inputs and Outputs

More information

3.3V ZERO DELAY CLOCK MULTIPLIER

3.3V ZERO DELAY CLOCK MULTIPLIER 3.3V ZERO DELAY CLOCK MULTIPLIER FEATURES: Phase-Lock Loop Clock Distribution for Applications ranging from 10MHz to 1 operating frequency Distributes one clock input to two banks of four outputs Separate

More information

DUAL AUTO-ZEROED OPERATIONAL AMPLIFIERS TC913A TC913B GENERAL DESCRIPTION FEATURES ORDERING INFORMATION

DUAL AUTO-ZEROED OPERATIONAL AMPLIFIERS TC913A TC913B GENERAL DESCRIPTION FEATURES ORDERING INFORMATION DUL UTO-ZEROED FETURES First Monolithic Dual uto-zeroed Operational mplifier Chopper mplifier Performance Without External Capacitors V OS... µv Max V OS Drift....µV/ C Max Saves Cost/ssembly of Four "Chopper"

More information

LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631)

LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) LSI/CSI LS7766 UL 3800 LSI Computer Systems, Inc. 1235 Walt Whitman Road, Melville, NY 11747 (631) 271-0400 FX (631) 271-0405 June 2012 32-IT SINGLE- XIS/DUL-XIS QUDRTURE COUNTER FETURES: Direct interface

More information

LC75836W/D. 1/4-Duty General-Purpose LCD Driver

LC75836W/D. 1/4-Duty General-Purpose LCD Driver 1/4-Duty General-Purpose LCD Driver Overview The LC75836W is 1/4-duty general-purpose microprocessor-controlled LCD driver that can be used in applications such as frequency display in products with electronic

More information

DEFROST and REHEAT key interlock each other, and BEGAL key is individual. Output driver. Key scan. System Oscillator.

DEFROST and REHEAT key interlock each other, and BEGAL key is individual. Output driver. Key scan. System Oscillator. PT8A5A Features Operating voltage:.5v~5.5v. Have Defrost, eheat and Bagel function elay output disable without external oscillator Adjustable timer: 0s~0mins Few external components Low cost 8-Pin DIP

More information

MC74HC4538A. Dual Precision Monostable Multivibrator (Retriggerable, Resettable)

MC74HC4538A. Dual Precision Monostable Multivibrator (Retriggerable, Resettable) Dual Precision Monostable Multivibrator (Retriggerable, Resettable) The is identical in pinout to the MC4538. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are

More information

MM5452/MM5453 Liquid Crystal Display Drivers

MM5452/MM5453 Liquid Crystal Display Drivers MM5452/MM5453 Liquid Crystal Display Drivers General Description The MM5452 is a monolithic integrated circuit utilizing CMOS metal gate, low threshold enhancement mode devices. It is available in a 40-pin

More information

Regulating Pulse Width Modulators

Regulating Pulse Width Modulators Regulating Pulse Width Modulators UC1525A/27A FEATURES 8 to 35V Operation 5.1V Reference Trimmed to ±1% 100Hz to 500kHz Oscillator Range Separate Oscillator Sync Terminal Adjustable Deadtime Control Internal

More information

Low Power Consumption IPS009BL9_BL9A_BLAA AT Cut 32KHz SPXO

Low Power Consumption IPS009BL9_BL9A_BLAA AT Cut 32KHz SPXO Description IPS009BL9, IPS009BL9A and is the specific SPXO IC for achieving 32KHz output by divide, corresponding to the fundamental crystal from 14MHZ to 27MHz and 33.554MHz corresponding to each IC.

More information

8-bit shift register and latch driver

8-bit shift register and latch driver 8-bit shift register and latch driver The BU2114 and BU2114F are CMOS ICs with low power consumption, and are equipped with an 8-bit shift register latch. Data in the shift register can be latched asynchronously.

More information

3.3V ZERO DELAY CLOCK BUFFER, SPREAD SPECTRUM COMPATIBLE

3.3V ZERO DELAY CLOCK BUFFER, SPREAD SPECTRUM COMPATIBLE 3.3V ZERO DELAY CLOCK BUFFER, SPREAD SPECTRUM COMPATIBLE IDT23S05 FEATURES: Phase-Lock Loop Clock Distribution 10MHz to 133MHz operating frequency Distributes one clock input to one bank of five outputs

More information

PT7C4511. PLL Clock Multiplier. Features. Description. Pin Configuration. Pin Description

PT7C4511. PLL Clock Multiplier. Features. Description. Pin Configuration. Pin Description Features Zero ppm multiplication error Input crystal frequency of 5-30 MHz Input clock frequency of - 50 MHz Output clock frequencies up to 200 MHz Peak to Peak Jitter less than 200ps over 200ns interval

More information

HCF4040B RIPPLE-CARRY BINARY COUNTER/DIVIDERS 12 STAGE

HCF4040B RIPPLE-CARRY BINARY COUNTER/DIVIDERS 12 STAGE RIPPLE-CARRY BINARY COUNTER/DIVIDERS 12 STAGE MEDIUM SPEED OPERATION : t PD = 80ns (TYP.) at V DD = 10V FULLY STATIC OPERATION COMMON RESET BUFFERED INPUTS AND OUTPUTS STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS

More information

INTRODUCTION FEATURES ORDERING INFORMATION APPLICATIONS LOW POWER DTMF RECEIVER 18 DIP 300A

INTRODUCTION FEATURES ORDERING INFORMATION APPLICATIONS LOW POWER DTMF RECEIVER 18 DIP 300A LOW POWER DTMF RECEIVER INTRODUCTION The is a complete Dual Tone Multiple Frequency (DTMF) receiver that is fabricated by low power CMOS and the Switched- Capacitor Filter technology. This LSI consists

More information

MC MOTOROLA CMOS SEMICONDUCTOR TECHNICAL DATA

MC MOTOROLA CMOS SEMICONDUCTOR TECHNICAL DATA SEMICONDUCTOR TECHNICAL DATA Order this document by MC456/D CMOS The MC456 is a phase locked loop (PLL) frequency synthesizer constructed in CMOS on a single monolithic structure. This synthesizer finds

More information

NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package.

NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package. DECADE COUNTER; 4-BIT BINARY COUNTER The SN54/ and SN54/ are high-speed 4-bit ripple type counters partitioned into two sectio. Each counter has a divide-by-two section and either a divide-by-five () or

More information

LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631)

LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631) LSI/CSI LS7366 UL LSI Computer Systems, Inc. 1235 Walt Whitman Road, Melville, NY 11747 (631) 271-0400 FX (631) 271-0405 3800 32-IT QUDRTURE COUNTER WITH SERIL INTERFCE GENERL FETURES: Operating voltage:

More information

BiMOS II 8-BIT SERIAL-INPUT, LATCHED DRIVERS

BiMOS II 8-BIT SERIAL-INPUT, LATCHED DRIVERS 5841 ND 5842 5841 ND 5842 BiMOS II 8-BIT SERIL-INPUT, LTCHED DRIVERS Data Sheet 26185.14B* UCN5841 & UCN5842 BSOLUTE MXIMUM RTINGS at 25 C Free-ir Temperature Output Voltage, V CE (UCN5841 & 5841SLW)......

More information

3.3 VOLT COMMUNICATIONS CLOCK PLL MK Description. Features. Block Diagram DATASHEET

3.3 VOLT COMMUNICATIONS CLOCK PLL MK Description. Features. Block Diagram DATASHEET DATASHEET 3.3 VOLT COMMUNICATIONS CLOCK PLL MK2049-45 Description The MK2049-45 is a dual Phase-Locked Loop (PLL) device which can provide frequency synthesis and jitter attenuation. The first PLL is VCXO

More information

UCS Channel LED Driver / Controller

UCS Channel LED Driver / Controller GENERAL DESCRIPTION 3-Channel LED Driver / Controller The UCS1903 is a 3-channel LED display driver / controller with a built-in MCU digital interface, data latches and LED high voltage driving functions.

More information

CD4047BC Low Power Monostable/Astable Multivibrator

CD4047BC Low Power Monostable/Astable Multivibrator Low Power Monostable/Astable Multivibrator General Description The CD4047B is capable of operating in either the monostable or astable mode. It requires an external capacitor (between pins 1 and 3) and

More information

CD4063BMS. CMOS 4-Bit Magnitude Comparator. Pinout. Features. Functional Diagram. Applications. Description. December 1992

CD4063BMS. CMOS 4-Bit Magnitude Comparator. Pinout. Features. Functional Diagram. Applications. Description. December 1992 CD3BMS December 99 Features CMOS -Bit Magnitude Comparator Pinout High Voltage Type (V Rating) Expansion to 8,,... N Bits by Cascading Units CD3BMS TOP VIEW Medium Speed Operation - Compares Two -Bit Words

More information

M63850P/FP. PRELIMINARY Notice: This is not a final specification. MITSUBISHI SEMICONDUCTOR <TRANSISTOR ARRAY> 4-UNIT 1.5A DMOS ARRAY WITH CLAMP DIODE

M63850P/FP. PRELIMINARY Notice: This is not a final specification. MITSUBISHI SEMICONDUCTOR <TRANSISTOR ARRAY> 4-UNIT 1.5A DMOS ARRAY WITH CLAMP DIODE M685P/FP -UNIT DMOS RRY WITH CLMP DIODE DESCRIPTION The M685P/FP is a inverter input power DMOS transistor array that consists of independent output N-channel DMOS transistors. PIN CONFIGURTION COM O 6

More information

Adaptive Power MOSFET Driver 1

Adaptive Power MOSFET Driver 1 Adaptive Power MOSFET Driver 1 FEATURES dv/dt and di/dt Control Undervoltage Protection Short-Circuit Protection t rr Shoot-Through Current Limiting Low Quiescent Current CMOS Compatible Inputs Compatible

More information

NT7605. Single-chip 20C X 2L Dot-Matrix LCD Controller / Driver. Features. General Description 1 V2.1

NT7605. Single-chip 20C X 2L Dot-Matrix LCD Controller / Driver. Features. General Description 1 V2.1 Single-chip 20C X 2L Dot-Matrix LCD Controller / Driver Features! Internal LCD drivers 6 common signal drivers 00 segment signal drivers! Maximum display dimensions 20 characters * 2 lines or 40 characters

More information

Video switch for CANAL-Plus decoder

Video switch for CANAL-Plus decoder Video switch for CANAL-Plus decoder The BA7630S and BA7630F are decoder switching ICs for the scrambled broadcasts in France. The ICs include a 3- input multiplexer, -input multiplexers with amplifiers,

More information

MK VCXO-BASED FRAME CLOCK FREQUENCY TRANSLATOR. Features. Description. Block Diagram DATASHEET. Pullable Crystal

MK VCXO-BASED FRAME CLOCK FREQUENCY TRANSLATOR. Features. Description. Block Diagram DATASHEET. Pullable Crystal DATASHEET MK2059-01 Description The MK2059-01 is a VCXO (Voltage Controlled Crystal Oscillator) based clock generator that produces common telecommunications reference frequencies. The output clock is

More information

SERIALLY PROGRAMMABLE CLOCK SOURCE. Features

SERIALLY PROGRAMMABLE CLOCK SOURCE. Features DATASHEET ICS307-02 Description The ICS307-02 is a versatile serially programmable clock source which takes up very little board space. It can generate any frequency from 6 to 200 MHz and have a second

More information

ICS663 PLL BUILDING BLOCK

ICS663 PLL BUILDING BLOCK Description The ICS663 is a low cost Phase-Locked Loop (PLL) designed for clock synthesis and synchronization. Included on the chip are the phase detector, charge pump, Voltage Controlled Oscillator (VCO)

More information

Obsolete Product(s) - Obsolete Product(s)

Obsolete Product(s) - Obsolete Product(s) DUAL MONOSTABLE MULTIVIBRATOR RETRIGGERABLE/RESETTABLE CAPABILITY TRIGGER AND RESET PROPAGATION DELAYS INDEPENDENT OF R X, C X TRIGGERING FROM LEADING OR TRAILING EDGE Q AND Q BUFFERED OUTPUT AVAILABLE

More information

HCF4538B DUAL MONOSTABLE MULTIVIBRATOR

HCF4538B DUAL MONOSTABLE MULTIVIBRATOR DUAL MONOSTABLE MULTIVIBRATOR RETRIGGERABLE/RESETTABLE CAPABILITY TRIGGER AND RESET PROPAGATION DELAYS INDEPENDENT OF R X, C X TRIGGERING FROM LEADING OR TRAILING EDGE Q AND Q BUFFERED OUTPUT AVAILABLE

More information

NT7603. Features. General Description

NT7603. Features. General Description PRELIMINARY Single-Chip 16Cx2L Dot-Matrix LCD Controller / Driver Features Internal LCD drivers 16 common signal drivers 80 segment signal drivers Maximum display dimensions 16 characters * 2 lines or

More information

ELM409 Versatile Debounce Circuit

ELM409 Versatile Debounce Circuit ersatile Debounce Circuit Description The ELM is digital filter circuit that is used to interface mechanical contacts to electronic circuits. All mechanical contacts, whether from switches, relays, etc.

More information

UNISONIC TECHNOLOGIES CO., LTD

UNISONIC TECHNOLOGIES CO., LTD U UNISONIC TECHNOLOGIES CO., LTD REGULATING PWM IC DESCRIPTION The UTC U is a pulse width modulator IC and designed for switching power supplies application to improve performance and reduce external parts

More information

AUTOMOTIVE DIGITAL CLOCK IC IN7100 TECHNICAL DATA DESCRIPTION DIP-40

AUTOMOTIVE DIGITAL CLOCK IC IN7100 TECHNICAL DATA DESCRIPTION DIP-40 TECHNICAL DATA AUTOMOTIVE DIGITAL CLOCK IC IN7100 DESCRIPTION IN7100 is a automotive digital clock, CMOS LSI. It drives fluorescent indicator panel directly. It can be driven by a 4.194304 MHz crystal

More information

5V Automotive Regulator with Windowed Watchdog. Features. Applications. Selection Table. Part Number V REF

5V Automotive Regulator with Windowed Watchdog. Features. Applications. Selection Table. Part Number V REF EM MICOELECTONIC - MAIN SA 5V Automotive egulator with Windowed Watchdog Description The offers a high level of integration by combining voltage regulation, voltage monitoring and software monitoring using

More information

General Purpose Clock Synthesizer

General Purpose Clock Synthesizer 1CY 290 7 fax id: 3521 CY2907 General Purpose Clock Synthesizer Features Highly configurable single PLL clock synthesizer provides all clocking requirements for numerous applications Compatible with all

More information

SN54221, SN54LS221, SN74221, SN74LS221 DUAL MONOSTABLE MULTIVIBRATORS WITH SCHMITT-TRIGGER INPUTS

SN54221, SN54LS221, SN74221, SN74LS221 DUAL MONOSTABLE MULTIVIBRATORS WITH SCHMITT-TRIGGER INPUTS Dual Versions of Highly Stable SN542 and SN742 One Shots SN5422 and SN7422 Demonstrate Electrical and Switching Characteristics That Are Virtually Identical to the SN542 and SN742 One Shots Pinout Is Identical

More information

Output format same as L, except that when HP1 or HP2 is active, it will clear CP1. VDD GND. Rx IN OSC HP1 CODE 2 HP2 SC9149AL/ 9149AHN HP3 HP4 SP2

Output format same as L, except that when HP1 or HP2 is active, it will clear CP1. VDD GND. Rx IN OSC HP1 CODE 2 HP2 SC9149AL/ 9149AHN HP3 HP4 SP2 INFRARED REMOTE CONTROL RECEIVER DESCRIPTION The are CMOS LSIs designed for use on the infrared remote control receiver, and when this LSI is used in combination with SC4A for transmitter, the remote control

More information