12.1 XGA Very High Bright TFT-LCD LVM121XSB-02-L01

Size: px

Start display at page:

Download "12.1 XGA Very High Bright TFT-LCD LVM121XSB-02-L01"

Coral Craig
5 years ago
Views:

1 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX FINAL PRODUCT INFORMATION (All information in this technical data sheet is subject to change without notice.) Updated 6/3/29 2. XGA Very High Bright TFTLCD LVM2XSB2L PRODUCT ENGINEERING DEPT. Vertex LCD Inc. Name Signature Date CREATED BY Tom Kim 6/3/29 REVIEWED BY Eric Kim 7/9/29 APPROVED BY Ed Kang 7/3/29 Vertex LCD Inc. (/23) LVM2XSB2L Rev. C

2 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX CONTENTS NO. ITEM Page COVER CONTENTS 2 REVISION HISTORY 3 GENERAL DESCRIPTION 4 2 ABSOLUTE MAXIMUM RATINGS 4 3 ELECTRICAL CHARACTERISTICS 5 4 POWER ON/OFF SEQUENCE 6 5 INTERFACE CONNECTION 7 5. RECOMMENDED LVDS TRANSMITTER 8, 9 6 SIGNAL TIMING SPECIFICATIONS 7 TIMING WAVE FORM 8 COLOR INPUT DATA REFERENCE 2 9 BLOCK DIAGRAM 3 OPTICAL SPECIFICATIONS 4 MECHANICAL CHARACTERISTICS 5 2 MECHANICAL SPECIFICATIONS 6, 7 3 RELIABILITY 8 4 PACKING FORM 9 5 PRECAUTIONS 2 5. MOUNTING PRECAUTION OPERATING PRECAUTION 2, ELECTROSTATIC DISCHARGE CONTROL STORAGE HANDLING PRECAUTION FOR PROTECTION FILM 2 A OPTICAL CHARACTERISTIC MEASUREMENT EQUIPMENT AND METHOD 22 B LUMINANCE 22 C RESPONSE TIME 23 D VIEWING ANGLE 23 Vertex LCD Inc. (2/23) LVM2XSB2L Rev. C

3 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX Revision History Rev ECN No. Description of changes Date Prepared Initial release 4/25/6 Brian Yi A B Change. Absolute Maximum Rating(P4) Operating Temperature 25~85 o C ~5 o C Storage Temperature 25~85 o C 2~6 o C 2. Reliability Condition(P8) High temperature storage test Ta = 85 o C, 24hr Ta = 6 o C, 24hr Low temperature storage test Ta = 25 o C, 24hr Ta = 2 o C, 24hr High temperature & high humidity operation test Ta = 85 o C, 8%RH Ta = 5 o C, 8%RH High temperature operation test Ta = 85 o C, 24hr Ta = 5 o C, 24hr Low temperature operation test Ta = 25 o C, 24hr Ta = o C, 24hr Thermal Shock Ta = 25 o C ~ 85 o C Ta = 2 o C ~ 6 o C Change. Surface treatments(p4,p5) antireflective, clear Anti Glare 2. Absolute Maximum Rating(P4) Backlight Vcc Min. V Max..4V Min. V Max. 8.V Backlight Icc Min. A Max. 2.6A Min. A Max..72A 3. Electrical Characteristic (P5) Back light operating voltage Max. 7.7V 8.V Back light Power consumption Max W 2.96W 4. Power Consumption (LCD & Backlight Only)(P4) Total 3.5 Watt, typ. 2.7 Total 3.66 Watt, typ /29/7 Eric Kim /27/7 Eric Kim C VEECN94 Mechanical Specification changed. (P6) 9.89mm,.4mm, 3.72mm 9.59mm,.mm, 3.42mm 3 on backlight only deleted. (P8) 4. Packing Foam modified. (P9) 5.2 (6) Thermal Map added. (P2~P2) 6/3/9 Tom Kim Vertex LCD Inc. (3/23) LVM2XSB2L Rev. C

4 Vertex LCD Inc. 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX General Description LVM2XSB2L is 2. Color Active Matrix Liquid Crystal Display with an integral LED backlight system. The matrix employs amorphous silicon Thin Film Transistor as the active element. It is a transmissive type display operating in the normally black mode. This TFTLCD has a 2. inch diagonally measured active display area with XGA resolution (24 horizontal by 768 vertical pixel array). Each pixel is divided into Red, Green and Blue subpixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the subpixel color is determined with a 6bit gray scale signal for each dot, thus presenting a palette of more than 262,44 colors. The LVM2XSB2L is intended to support applications where high brightness is a critical factor. In combination with the vertical arrangement of the subpixels, the LVM2XSB2L characteristics provide an excellent flat panel display for avionics (general & military), rugged environment, outdoor or anywhere daylight applications required. General Specification General specifications are summarized in the following table ITEM SPECIFICATION Active screen size 2. inches(3.7cm) diagonal (H) X 84.32(V) mm Outline dimensions 274.(H) 26.3(V) 3.6(D) mm Pixel pitch.24(h) mm.24(v) mm Pixel format 24(H) X 768(V) pixels Color Pixel Arrangement RGB stripe arrangement Color depth 6bit, 262,44 colors Brightness cd/m 2 Power Consumption (LCD & Backlight only) Total 3.66 Watt, typ Weight 9g (typ) Display operating mode transmissive mode, normally Black Surface treatments hard coating(3h), Anti Glare Backlight Unit White LED 2. Absolute Maximum Rating Parameter symbol Min. Values Max. Units Notes Power Input Voltage Display Backlight VCC Vcc Icc Operating Temperature TOP Storage Temperature TST Note Humidity 9% RH. No condensation Vdc Vdc A o C o C at 25 o C 2 2 Vertex LCD Inc. (4/23) LVM2XSB2L Rev. C

5 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX Electrical Characteristics The LVM2XSB2L requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second input which powers the LED backlight, is typically generated by LED driver board. The LED driver board is an external unit to the LCD. Parameter Symbol Values Units Notes Min. Typ. Max. MODULE Power Supply Input Voltage VCC Vdc Vcc = 3.3 V Power Supply Input Current ICC.24 A, 2 Power Consumption Pc.7 Watts, 2 LED Backlight Operating Voltage Operating Current VBL IBL Vdc Adc 4 4 Power Consumption 2.96 Watts 3 Life Time 4, 5, Hrs Notes. The current draw and power consumption specified is for 3.3 Vdc at 25 o C and fv at 6Hz.(at Black pattern displayed) 2. Logic level are specified for Vcc of 3.3 Vdc at 25 o C. The values specified apply to all logic inputs; Hsync, Vsync, Clock, data signals, etc. 3. The life time is determined as the time at which brightness of lamp is 5% compare to that of initial value at the typical LED current & at ambient temperature of 25 o C. 4. LVM2XSB2L load voltage should be about 7.7V at 36mA max current per top and bottom sides. 36mA max LVM2XSB2L BLU Power 36mA max Vertex LCD Inc. (5/23) LVM2XSB2L Rev. C

6 4. Power On/Off Sequences 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX To prevent a latchup or DC operation of the LCD module, the power on/off sequence should be as shown below. Power Supply.9VDD.VDD V T.9VDD.VDD T2 T5 T6 Interface Signal Valid T3 T4 Back light < T ms < T2 5 ms ms T3, T4 < T5 5 ms sec < T6 Note. Please avoid floating state of interface signal at invalid period. 2. When the interface signal is invalid, be sure to pull down the power supply for LCD Vcc to Vcd. 3. Backlight power must be turn on after power supply for LCD and interface signal is valid. Vertex LCD Inc. (6/23) LVM2XSB2L Rev. C

7 Vertex LCD Inc. 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX Interface Connections CN (interface signal) LVM2XSB2L uses 2 pin connector for module electronics. Used connector DF9L2PH (HIROSE Electric Co. LTD) Matching side DF9G2SC (HIROSE) Pin Symbol Description VDD VDD2 Vss Vss RIN RIN+ VSS RIN RIN+ VSS RIN2 RIN2+ VSS RCLK IN RCLK IN+ VSS NC NC VSS VSS Power supply +3.3V Power supply +3.3V Ground Ground Transmission Data of Pixel () Transmission Data of Pixel (+) Ground Transmission Data of Pixel () Transmission Data of Pixel (+) Ground Transmission Data of Pixel 2 () Transmission Data of Pixel 2 (+) Ground Sampling Clock () Sampling Clock (+) Ground No Connection No Connection Ground Ground CN 2(backlight) LVM2XSB2L employs Molex 542 or equivalent connectors for the LED backlight. Pin Symbol Description Notes 2 V Ground Lamp power input Ground Vertex LCD Inc. (7/23) LVM2XSB2L Rev. C

8 5.. Recommended Transmitter to LVM2XSB2L 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX Bit Transmitter (THC63LVDM63A) THC63LVDM63A Input Terminal No. Input Signal (Graphic controller output signal) Symbol THC63LVDM63A Symbol Function LVM2XSB2L Interface (CN) Output Signal Symbol Terminal Symbol TIN 44 R Red Pixels Display Data (LSB) TIN 45 R Red Pixels Display Data TIN2 47 R2 Red Pixels Display Data TIN3 48 R3 Red Pixels Display Data TIN4 R4 Red Pixels Display Data TIN5 3 R5 Red Pixels Display Data (MSB) TIN6 4 G Green Pixels Display Data (LSB) TIN7 6 G Green Pixels Display Data TIN8 7 G2 Green Pixels Display Data TIN9 9 G3 Green Pixels Display Data TIN G4 Green Pixels Display Data TIN 2 G5 Green Pixels Display Data (MSB) TIN2 3 B Blue Pixels Display Data (LSB) TIN3 5 B Blue Pixels Display Data TIN4 6 B2 Blue Pixels Display Data TIN5 8 B3 Blue Pixels Display Data TIN6 9 B4 Blue Pixels Display Data TIN7 2 B5 Blue Pixels Display Data (MSB) TIN8 22 Hsync Horizontal Synchronization Signal TIN9 23 Vsync Vertical Synchronization Signal TIN2 25 DE Compound Synchronization Signal OUT OUT+ OUT OUT + OUT2 OUT2 + CLK IN 26 NCLK Data Sampling Clock CLK OUT CLK OUT + No. 5 No. 6 No. 7 No. 8 No. 9 No. No. No. 2 IN IN + IN IN + IN2 IN2 + CLK IN CLK IN + Vertex LCD Inc. (8/23) LVM2XSB2L Rev. C

9 8 Bit Transmitter (THC63LVDM83A) Vertex LCD Inc. 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX THC63LVDM83A LVM2XSB2L Input Terminal No. Input Signal (Graphic controller output signal) Output Signal Symbol Interface (CN) Symbol THC63LVDM83 Symbol Function Terminal Symbol TIN 5 R Red Pixels Display Data (LSB) TIN 52 R Red Pixels Display Data TIN2 54 R2 Red Pixels Display Data TIN3 55 R3 Red Pixels Display Data TIN4 56 R4 Red Pixels Display Data TIN6 3 R5 Red Pixels Display Data (MSB) TIN7 4 G Green Pixels Display Data (LSB) TIN8 6 G Green Pixels Display Data TIN9 7 G2 Green Pixels Display Data TIN2 G3 Green Pixels Display Data TIN3 2 G4 Green Pixels Display Data TIN4 4 G5 Green Pixels Display Data (MSB) TIN5 5 B Blue Pixels Display Data (LSB) TIN8 9 B Blue Pixels Display Data TIN9 2 B2 Blue Pixels Display Data TIN2 22 B3 Blue Pixels Display Data TIN2 23 B4 Blue Pixels Display Data TIN22 24 B5 Blue Pixels Display Data (MSB) TIN24 27 Hsync Horizontal Synchronization Signal TIN25 28 Vsync Vertical Synchronization Signal TIN26 3 DE Compound Synchronization Signal TIN27 5 NC Non Connection (open) TIN5 2 NC Non Connection (open) TIN 8 NC Non Connection (open) TIN NC Non Connection (open) TIN6 6 NC Non Connection (open) TIN7 8 NC Non Connection (open) TIN23 25 NC Non Connection (open) OUT OUT + OUT OUT + OUT2 OUT2 + OUT3 OUT3 + CLK IN 3 NCLK Data Sampling Clock CLK OUT CLK OUT + No. 5 No. 6 No. 7 No. 8 No. 9 No. No. No. 2 IN IN + IN IN + IN2 IN2 + CLK IN CLK IN + Vertex LCD Inc. (9/23) LVM2XSB2L Rev. C

10 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX Signal Timing Specification The 2.XGA LCM is only operated by the DE mode Item Symbols Min Typ Max Units Frequency /Tc 65 8 MHz Clock High Time Tch 4.5 Ns Low Time Tcl 4.5 Ns Data Setup Time Tds 2.7 Ns Hold Time Tdh Ns Data Enable Setup Time Tes 2.7 Ns Frame Period Tv Lines Vertical Display Period Tvd Lines One Line Scanning Period Th Clocks Horizontal Display Period Thd Clocks Note ) Refer to TIMING CHART and LVDS (THC63LVDF64A) specifications by Thine Electronics Inc. Note 2) If NCLK is fixed to H or L level for certain period, the panel may be damaged. Note 3) Please adjust LCD operating signal timing and FL driving frequency, to optimize the display quality. Note 4) Do not hold NCLK on H level nor L level during VDD (+3.3V) is supplied. When it holds on, DC voltage supplies to liquid crystal materials and it may cause damage to liquid crystal materials. Note 5) Do not make tv, tvhd and tvds fluctuate. If tv, tvhd and tvds are fluctuated, then panel displays black. Note 6) NCLK count of each Horizontal Scanning Time should be always the same. VBlanking period should be n X Horizontal Scanning Time. (n integer) LVDS Rx interface timing parameter Item Symbol Min Typ. Max Unit Remark CLKIN Period trcip nsec Input data trip nsec Input data trip * tripc/7.4 * tripc/7 * tripc/7+.4 nsec Input data 2 trip6 2 * tripc/7.4 2 * tripc/7 2 * tripc/7+.4 nsec Input data 3 trip5 3 * tripc/7.4 3 * tripc/7 3 * tripc/7+.4 nsec Input data 4 trip4 4 * tripc/7.4 4 * tripc/7 4 * tripc/7+.4 nsec Input data 5 trip3 5 * tripc/7.4 5 * tripc/7 5 * tripc/7+.4 nsec Input data 6 trip2 6 * tripc/7.4 6 * tripc/7 6 * tripc/7+.4 nsec trip2 trip3 trip4 trip5 trip6 trip trip RINz +/ Rx3 Rx2 Rx Rx Rx6 Rx5 Rx4 Rx3 Rx2 Rx Rx Vdiff=[v] Vdiff=[v] RCLKIN+ trcip * Z=,, 2, 3 Vertex LCD Inc. (/23) LVM2XSB2L Rev. C * Vdiff = (RINz+)(RINz), (RCLKIN+)(RCLKIN)

11 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX Timing Wave Form(DE Mode) Vertical Timing Waveforms Tv Tvd MCLK Th ENAB R7 ~ R G7 ~ G B7 ~ B Invalid Data x, x,2 x,y x,768 Invalid Data x+, Horizontal Timing Waveforms Thd Th MCLK Tc ENAB RA7 ~RA GA7 ~GA BA7 ~BA D D2 Dn D22 D23 D24 Invalid Data D D2 D3 Tch Tcl MCLK.5V 2.V.8V Tds Tdh Data V a lid Data 2.V.8V Tes ENAB 2.V Vertex LCD Inc. (/23) LVM2XSB2L Rev. C

12 (2/23) LVM2XSB2L Rev. C Vertex LCD Inc. 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX Color Input Data Reference The brightness of each primary color(red, green and blue) is based on the 6bit gray scale data input for the color; the higher the binary input, the brighter the color. The table below provides a reference for color versus data input. Display R5 R4 R3 R2 R R G5 G4 G3 G2 G G B5 B4 B3 B2 B B Basic Colors Black Blue Green Light Blue Red Purple Yellow White Red Red() Dark Red() Red(2) Red(6) Red(62) Red(63) Bright Green Green()Dark Green() Green(2) Green(6) Green(62) Green(63)Bright Blue Blue() Dark Blue() Blue(2) Blue(6) Blue(62) Blue(63) Bright White & Black Black() Dark () (2) (6) (62) White(63) Bright

13 9. Block Diagram 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX Panel Controller + LVDS Column driver circuit CN DC/DC Converter Gray scale Row Driver circuit TFTLCD (24 768) Manipulation Voltage Generation Circuit D/A Converter Circuit CN2 Backlight Ass y Vertex LCD Inc. (3/23) LVM2XSB2L Rev. C

14 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX Optical Specifications Optical characteristics are determined in a dark environment at 25 o C. The values specified are at an approximate distance 5cm from the LCD surface at a viewing angle of Φ and θ equal to. Appendix A presents additional information concerning the measurement equipment and method. Parameter Symbol Values Units Notes Min. Typ. Max. Contrast Ratio CR 4 Surface Luminance, white LWH cd/m 2 2 Luminance Uniformity δ WHITE 7% 3 Response Time Total(Tr + Td) 4 msec 4 CIE Color Coordinates Red Green Blue White xr yr xg yg xb yb xw yw Viewing Angle x axis, right ( =º) x axis, left( =8º) y axis, up( =9º) y axis, down ( =27º) θ x θ x θ y θ y degree 5 Notes. Contrast Ratio (CR) is defined mathematically as Contrast Ratio = Surface Luminance with all white pixels Surface Luminance with all black pixels 2. Surface luminance is the center point across the LCD surface 5cm from the surface with all pixels displaying white. For more information see Appendix B. 3. The uniformity in surface Luminance, δ WHITE is determined by measuring LON at each test position through 9, and then dividing the minimum LON of 9 points luminance by maximum LON of 9 points luminance and multiply by for percentage value. For more information see Appendix B. δ WHITE = Minimum (LON, LON2,...LON9) * / Maximum (LON, LON2,...LON9) 4. Response time is the time required for the display to transition from white to black (Rise Time, TrR) and from black to white (Decay Time, TrD). For additional information see Appendix C. 5. Viewing angle is the angle at which the contrast ratio is greater than. The angles are determined for the horizontal or xaxis and the vertical or yaxis with respect to the zaxis which is normal to the LCD surface. For more information see Appendix D. Vertex LCD Inc. (4/23) LVM2XSB2L Rev. C

15 . Mechanical Characteristics Vertex LCD Inc. 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX The chart below provides general mechanical characteristics for the model LVM2XSB2L. In addition, the figure below is a detailed mechanical drawing of the LCD. Note that dimensions are given for reference purposes only. Outside dimensions Horizontal Vertical Depth Bezel area Horizontal Vertical Active Display area Horizontal Vertical Weight (approximate) 274. ±.5 mm 26.3 ±.5 mm 3.6 ±.5 mm 25.4 mm 88.9 mm mm mm 9 g Surface Treatment Hard coating 3H. Antiglare treatment of the front polarizer. Vertex LCD Inc. (5/23) LVM2XSB2L Rev. C

16 2. Mechanical Specification < FRONT VIEW > 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX Vertex LCD Inc. (6/23) LVM2XSB2L Rev. C

17 <REAR VIEW> 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX Vertex LCD Inc. (7/23) LVM2XSB2L Rev. C

18 3. Reliability 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX Environment test condition. No. Test ITEM Conditions High temperature storage test Ta = 6 o C, 24hr 2 Low temperature storage test Ta = 2 o C, 24hr 3 High temperature & high humidity operation test Ta = 5 o C, 8%RH 24hrs (no condensation) 4 High temperature operation test Ta = 5 o C, 24h 5 Low temperature operation test Ta = o C, 24h 6 Thermal Shock Ta = 2 o C ~ 6 o C (3 min), cycles 7 Shock test (nonoperating) Gravity 2G Pulse width 2ms, half sine wave for X, Y, Z direction 8 Vibration test (nonoperating) Frequency ~ 3 Hz Gravity/AMP.5G Period X, Y, Z 3 min. Result Evaluation Criteria There should be no change which might affect the practical display function when the display quality test is conducted under normal operating condition. Vertex LCD Inc. (8/23) LVM2XSB2L Rev. C

the bottom of the box Put Pad into the box Insert the module into the

As shown in the figure, place the Modules bundled in the box.

19 4. Packing Form 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX Put a bottom cover on the bottom of the box Put Pad into the box Insert the module into the shielding bag. As shown in the figure, place the Modules bundled in the box. Place a cover on the top of the box. Seal the box. a) Total weight Approx. 8kg b) Box Size 335(W)X 298(D) X 298(H) c) Package quantity in one box 6 pcs Vertex LCD Inc. (9/23) LVM2XSB2L Rev. C

20 5. PRECAUTIONS Please pay attention to the followings when you use this TFT/LCD module. 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX MOUNTING PRECAUTIONS () You must mount a module using holes arranged in four corners. (2) You should consider the mounting structure so that uneven force (ex. twisted stress) is not applied to the module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. (3) Please attach the surface with a transparent protective plate in order to protect the polarizer LC cell. Transparent protective plate should have sufficient strength in order to resist external force. (4) You should adopt radiation structure to satisfy the temperature specification. (5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former generates corrosive gas of attacking the polarizer at high temperature and the latter cause circuit break by electrochemical reaction. (6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB pencil lead. And Please do not rub with dust clothes with chemical treatment. Do not touch the surface of polarizer for bare hand or greasy cloth. (Some cosmetics are detrimental to the polarizer.) (7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaked with petroleum benzene. Normalhexane is recommended for cleaning the adhesives used to attach front / rear polarizers. Do not use acetone, toluen and alcohol because they cause chemical damage to the polarizer. (8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes deformations and color fading. (9) Do not open the case because inside circuits do not have sufficient strength. 5.2 OPERATING PRECAUTIONS () The spike noise causes the misoperation of circuits. It should be lower than following voltage V = ± 2mV (Over and under shoot voltage). (2) Response time depends on the temperature. (In lower temperature, it becomes longer.) (3) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur. (4) When fixed patterns are displayed for a long time, remnant image is likely to occur. (5) A module has high frequency circuit. It might be necessary to shield the electromagnetic noise in your integrating system. (6) The thermal map showing the heat imaging of the module (LVM2XSB2L) is shown in figure. Please reference the thermal map for optimum thermal design to maximize the MTBF of LED life. Vertex LCD Inc. (2/23) LVM2XSB2L Rev. C

6 S. Jefferson St. Unit K Placentia, CA 9287 TEL 742237 FAX 7422377 Figure. Thermal Map Showing the Heat Imaging of the LVM2XSB2L (REAR VIEW) 5.

21 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX Figure. Thermal Map Showing the Heat Imaging of the LVM2XSB2L (REAR VIEW) 5.3 ELECTROSTATIC DISCHARGE CONTROL Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wristband etc.. And don t touch I/F pin directly. 5.4 STORAGE When storing modules for a long time, the following precautions should be followed. () Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5 o C and 35 o C at normal humidity. (2) The polarizer surface should not come in contact with any other object. It is recommended that they be stored in the container in which they were shipped. 5.5 HANDLING PRECAUTIONS FOR PROTECTION FILM () When the protection film is peeled off, static electricity is generated between the film and polarizer. This should be peeled off slowly and carefully by people who are electrically grounded and with well ion blown equipment or in such a condition, etc.. (2) The protection film is attached to the polarizer with a small amount of glue. If some stress is applied to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to remain on the polarizer. Please carefully peel off the protection film without rubbing it against the polarizer. (3) When the module with protection film attached is stored for a long time, sometimes there remains a very small amount of glue still on the polarizer after the protection film is peeled off. (4) You can remove the glue easily. When the glue remains on the polarizer surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal hexane. Vertex LCD Inc. (2/23) LVM2XSB2L Rev. C

22 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX A. Optical Characteristic Measurement Equipment and Method Optical Stage(x,y) LCD Module Field = Topcon BM7 or equivalent 5mm B. Luminance <measuring point for luminance variation> <measuring point for surface luminance > mm from the left edge mm from the right edge mm from the top edge mm from the bottom edge Vertex LCD Inc. (22/23) LVM2XSB2L Rev. C

23 6 S. Jefferson St. Unit K Placentia, CA 9287 TEL FAX C. Response Time The response time is defined as the following figure and shall be measured by switching the input signal for black and white. % Ton Toff Optical Response 9 white black white D. Viewing angle <Definition of viewing angle range> ϕ = 9 o (2) yu θ = o z (Eye of inspector) θ ϕ ϕ = 8 o (9) xl xr ϕ = o (3) TFT LCD MODULE z yd ϕ = 27 o (6) Vertex LCD Inc. (23/23) LVM2XSB2L Rev. C

12.1 XGA Very High Bright TFT-LCD. LVM121XSB-411-L01 (based on HYDIS:HV121X02) COLOR LIQUID CRYSTAL DISPLAY

12.1 XGA Very High Bright TFT-LCD. LVM121XSB-411-L01 (based on HYDIS:HV121X02) COLOR LIQUID CRYSTAL DISPLAY TENTATIVE PRODUCT INFORMATION (All information in this technical data sheet is tentative and subject to change without notice.) Updated 4/25/26 2. XGA Very High Bright TFTLCD LVM2XSB4L (based on HYDISHV2X2)