Scotchcal Translucent Graphic Film IJ , FN and RG *

Transcription

1 Product Bulletin PIJ3630 Release G, Effective September 2010 (Replaces F, May 10) See Bulletin Change Summary at end of Bulletin Scotchcal Translucent Graphic Film IJ , FN and RG * For Solvent, UV and Latex Inkjet Printing and Cut Graphics 1. Product Description Films IJ and FN are 2-mil film for flat or thermoformed backlit graphics that have uniform color in both reflected and transmitted light. This white, translucent film has a synthetic layflat liner and clear, pressure-sensitive adhesive. It is approved for making permanent interior or exterior graphics. * Film RG is available for purchase and use with only a 3M Basic Product Warranty on a customer test and approve basis. 2. Recommended Types of Graphics and End Uses When constructed and used as described in this Bulletin, these types of graphics and end uses may be warranted by the 3M MCS Warranty or the 3M Performance Guarantee. Please read the entire Bulletin for details. For indoor or outdoor use on internally-illuminated vertical sign faces A. Limitations of End Uses This 3M product is not designed or recommended for the following uses. Please contact us to discuss other options. Not suitable for fleet graphics Not suitable for graphic constructions with more than two layers of film, including the overlaminate Graphics applied to: - surfaces with rivets or corrugations - non-3m flexible substrates - substrates with coatings such as silicone 3. Compatible Products This Bulletin provides details about the base film, recommended construction options, warranted durability and warranty limitations for the constructions shown in the Warranted Durability Tables. Additional specific information about compatible products can be found in the Product and Instruction Bulletins listed in 3M Related Literature at the end of this bulletin. A. Solvent Inkjet Inks and B. Latex Inkjet Inks and Ink Series Printer 3M Piezo Inkjet Ink Series 1500v2 EFI VUTEk 150, 2360/3360, 3300/5300 and 3000/5000 3M Piezo Inkjet Ink Series 4400 HP XLJet 1200 and M Piezo Inkjet Ink Series 4800 HP Scitex TJ8300, TJ8350 Series Digital Press* 3M Piezo Inkjet Ink Series 5500 Océ Arizona 600 Printer 3M Piezo Inkjet Ink Series 6200 Agfa :Jeti 3312, 3318, 3324, 5024 [Gandinnovations] HP 3M LX600 Specialty Latex Ink HP Designjet L65500, Scitex LX600 & LX800 Product Bulletin PIJ3630-1

2 C. UV Inkjet Inks and Ink Series Printer 3M Piezo Inkjet Ink Series 2200UV EFI VUTEk PV200 Printer 3M Piezo Inkjet Ink Series 2600UVv2 3M Printer 2500UV 3M Piezo Inkjet Ink Series 2700UV Durst Rho 160R, 351R 3M Piezo Inkjet Ink Series 2800UV EFI VUTEk QS2000, QS3200, QS3220, QS220 3M Piezo Inkjet Ink Series 5400UV HP Designjet H35000/45000 Mimaki Ink Series LF-200 Mimaki UJV-160, JFX-1631, JFC-1615R D. Graphic Protection 3M Screen Print UV Gloss Clear 9720i 3M Screen Print Clear 9720UV 3M Scotchcal Gloss Overlaminate M Scotchcal Luster Overlaminate M Scotchcal Matte Overlaminate M Scotchcal Luster Overlaminate M Scotchcal Matte Overlaminate M Scotchcal Luster Overlaminate M Scotchcal Matte Overlaminate M Scotchcal Ultra Matte Overlaminate 8915 E. Light Control Films 3M Diffuser Films M Diffuser Films M Blockout Film B 3M Blockout Film B F. Substrates 3M Panaflex Awning and Sign Facing 945GPS 3M Panagraphics III Wide-Width Flexible Substrate Flat, rigid substrates (see Application Characteristics) G. Other Products 3M Prespacing Tape SCPS-2 3M Prespacing Tape SCPS-53X 3M Premasking Tape SCPM-3 3M Premasking Tape SCPM-44X 4. Characteristics These are typical values for unprocessed product; processing may change the values. Contact your 3M representative for a custom specification. A. Physical Characteristics Characteristic Value Film Vinyl Colors Translucent white Thickness Without adhesive: 2 mils (0.05 mm) With adhesive: 3 to 4 mils (0.08 to 0.1 mm) Adhesive type Adhesive color Liner Adhesion 24 hours after application Chemical resistance Flammability Pressure sensitive Clear Polyethylene-coated paper Acrylic and uncoated, clear polycarbonate: 4 pounds/inch (0.7 kg/cm) Resists mild alkalis, mild acids, and salt Excellent resistance to water (not immersion) Call for information Product Bulletin PIJ3630-2

3 B. Application Characteristics Characteristic Value Finished graphic application recommendation Finished graphic exposure temperature Application temperature: 60 F (16 C) minimum air, substrate Application method: Wet, typical Surface type: Flat, without rivets Substrate type: 3M flexible substrates; Rigid substrates such as flat acrylic, polycarbonate, high temperature copolyester sheet, glass - These films typically adhere to solar-grade polycarbonate substrate. However, some lots of this substrate may inhibit film adhesion. Contact Technical Service if you are having difficulty. See Instruction Bulletin 5.7 for additional information. - Polycarbonate substrates may require oven drying before use because outgassing of moisture from the polycarbonate may cause the film to bubble. Refer to the manufacturers' instructions. -50 to +170 F (-45 to +77 C ) Impact at low temperatures of film applied to flexible substrates may result in cracking of the film and/or substrate. Graphic removal None, permanent C. 3M Flexible Substrates Important Note! The user is responsible for determining and complying with all applicable building codes that affect the use of materials in interior and exterior awning, banner and sign face applications, including flammability standards. For information on flammability requirements, contact your local building code officials. For information on the results of flammability testing on 3M flexible substrates, including the product covered in this Product Bulletin from 3M Commercial Graphics Division, call Definitions A. Exposure Types U.S. Vertical Exposure face of graphic The face of the graphic is +/- 10 from vertical. U.S. Desert Southwest Exposure Any outdoor graphic exposed to solar energy more than half of the daylight hours in Arizona, New Mexico and the desert areas of California, Nevada, Utah and Texas is subject to reduced warranties. A detailed map is available at 3Mgraphics.com under Warranties. U.S. Horizontal Exposure face of graphic The face of the graphic is +/- 5 from horizontal. U.S. Desert Southwest Exposure Any outdoor graphic exposed to solar energy more than half of the daylight hours in Arizona, New Mexico and the desert areas of California, Nevada, Utah and Texas is subject to reduced warranties. A detailed map is available at 3Mgraphics.com under Warranties. B. Graphic Types Indoor Signs Stationary graphics applied indoors and not exposed to the elements. Outdoor Signs Stationary graphics applied outdoors and exposed to the elements. C. Graphic Construction The products used to make a graphic, which may include film and/or flexible substrate, graphic protection, ink, printer and application tape. D. Graphic Protection Overlaminate films or clear coats used to protect the graphic and/or change gloss. Product Bulletin PIJ3630-3

4 6. Warranty Information A. Limitations and Disclaimers Applicable to All Warranties & Warranty Coverage Overview Both the warranty coverage and the durability for each graphic is based on the user(s) reading and following all applicable and current 3M Product and Instruction Bulletins. 3M will honor the Warranted Durability stated in the base film or substrate Product Bulletin that is current when the film was purchased. Warranted durabilities may be reduced and stipulations may apply for certain constructions and applications, as covered in this Bulletin. The following is made in lieu of all other express or implied warranties, including any implied warranty of merchantability or fitness for a particular purpose or implied warranty arising out of a course of dealing, custom or usage of trade. 3M will replace or refund the price of any 3M materials that do not meet this warranty within the specified time periods. These remedies are exclusive. In no case shall 3M be liable for any direct, indirect, or consequential damages, including any labor or non-3m materials charges. See the 3M Graphics Market Center Warranty Brochure at 3Mgraphics.com, which gives the terms, additional limitations of the warranty, if any, and limitations of liability. B. 3M Basic Product Warranty All 3M products are warranted to be free of defects in materials and manufacture at the time of shipment and to meet the specifications stated in this Product Bulletin and as further set forth in the 3M Graphics Market Center Warranty Brochure. C. 3M MCS Warranty Subject to Stipulations set forth in Section E., below (1) Warranted Durability Table for Finished Graphics in a Standard U.S. Vertical Exposure Finished graphics constructed with the materials specified and the exposure specified in the Warranted Durability Tables, Section C.(1), is eligible for the 3M MCS Warranty. For warranties for other exposures, see Section E.(1). OUT = Outdoor Signs IN = Indoor Signs HP VUTEk 150, 2360/ 3360, 3300/5300, 3000/5000 HP XLJet Series 1200, 1500 HP Scitex TJ8300 and TJ8350 Digital Presses SOLVENT Ink Series 1500v2 SOLVENT Ink Series 4400 SOLVENT Ink Series 4800 Graphic Protection VEH OUT IN VEH OUT IN VEH OUT IN 3619, , 8519, 8520, , DR UV i none Agfa:Jeti 3312, 3318, 3324, 5024 [Gandiinnovations] Océ Arizona 600 Printer Designjet L65500; Scitex LX600 & LX800 SOLVENT Ink Series 6200 SOLVENT Ink Series 5500 HP 3M LX600 Specialty Latex Ink Graphic Protection VEH OUT IN VEH OUT IN VEH OUT IN 3619, , 8519, 8520, , DR UV i none Product Bulletin PIJ3630-4

5 EFI VUTEk PV200 3M Printer 2500UV Durst RhoR & 351R Ink Series 2200UV Ink Series 2600UVv2 Ink Series 2700UV Graphic Protection VEH OUT IN VEH OUT IN VEH OUT IN 3619, , 8519, 8520, DR i, 9720UV none EFI VUTEk QS2000, QS3200, QS3220, QS220 HP Designjet H35000/45000 Mimaki UJV 160, JFX 1631 & 1615R Ink Series 2800UV Ink Series 5400UV Ink Series LF 200 Graphic Protection VEH OUT IN VEH OUT IN VEH OUT IN 3619, , 8519, 8520, DR 9720i, 9720UV none Note: IJ3630 may be applied to Panagraphics III Substrate with all listed graphic protection options or Panaflex Substrate 945GPS with overlaminate 3619, 3620, 8519, 8520 or D. 3M Performance Guarantee Subject to Stipulations set forth in Section E., below (1) Warranted Durability Table for 3M Product Performance Only in a Standard U.S. Vertical Exposure Graphics constructed with the 3M materials specified and in the exposure specified in the Warranted Durability Table, Section D.(1) eligible for the 3M Performance Guarantee. This warranty only covers the performance of the recommended 3M products used in the graphic construction when imaged with the printers and OEM inks listed in the most current version of Performance Guarantee Printer and Ink Matrix at 3Mgraphics.com. The Matrix may also list certain restrictions for using the film covered in this Bulletin. For warranties for other exposures, see Section E.(1). Warranted Durability of 3M Product Performance, in Years Film IJ3630 Graphic Protection DR UV i 8915 Outdoor Indoor 2 Inks and See the 3M Performance Guarantee Printer and Ink Matrix at 3Mgraphics.com, under Warranties E. General Warranty Stipulations for 3M MCS Warranty and 3M Performance Guarantee These stipulations apply to both the 3M MCS Warranty and 3M Performance Guarantee. General provisions for these stipulations are covered in the 3M Graphics Market Center Warranty Brochure at 3Mgraphics.com. Product Bulletin PIJ3630-5

6 (1) Reduced Warranted Durability for Non-vertical Graphics For graphics oriented in a non-vertical, outdoor exposure, multiply the warranted durability years for your graphic construction as shown in the applicable Warranted Durability Tables, Section C.(1) or Section D(1), by the percentage shown for the intended graphic exposure. If the Graphic Exposure is: Use this Percentage of U.S. Vertical Exposure, Warranted Durability Calculation Examples U.S. Non-vertical 50% (0.5) 0.5 x 5 years = 2 years 0.5 x 3 years = 1 years Desert Southwest Vertical 70% (0.7) 0.7 x 5 years = 2.8 years 0.7 x 3 years = 1.4 years Desert Southwest Non-vertical 35% (0.35) 0.35 x 5 years = 1.4 years 0.35 x 3 years = 0.7 years Horizontal 0% 0 (1) Abrasion and Loss of Gloss Abrasion damage and loss of gloss are not covered by any 3M warranty. This is considered normal wear and tear. (2) Application Outside the U.S. Contact the 3M organization for that country. (3) Application to Glass 3M accepts no liability for glass breakage when using this film for window graphics. See Instruction Bulletin 5.1 for details. (4) Graphics Made with Components Not Sold or Recommended by 3M 7. Factors that Affect Graphic Performance Life 3M does not warrant finished graphics made with inks, film, graphic protection and/or application tapes that are not sold or recommended by 3M. The user is solely responsible for the graphic appearance, performance and durability of graphic constructions that include any other products. The 3M Performance Guarantee covers selected 3M branded graphics products when used with qualified printers and inks. See the 3M Performance Guarantee Printer and Ink Matrix at The actual performance life of a graphic is affected by all of the following. The combination of graphics materials used Ink formulation Adequate ink drying or curing Selection, condition and preparation of the substrate Surface texture Application methods Angle and direction of sun exposure Environmental conditions Cleaning or maintenance methods 8. Graphics Manufacturing Refer to the 3M Related Literature section for a list of the Product and Instruction Bulletins that may be needed to make a graphic. A. Inkjet Printer Support Information! CAUTION Before using any equipment, always read the manufacturer's instructions for safe operation. (1) Ink Always read and follow the ink manufacturer's written instructions on usage. Product Bulletin PIJ3630-6

7 (2) Total Ink Coverage The maximum recommended total ink coverage for this film is: 270% when printed with all approved 3M inkjet solvent inks. 280% when printed with all approved 3M inkjet UV inks and latex inks. 250% when printed on the Mimaki JV5 Series printer with HS ink series (3M Performance Guarantee). Too high a total physical ink amount on the film results in media characteristic changes, inadequate drying, overlaminate lifting, and/or poor graphic performance. Refer to the Instruction Bulletin for the ink system being used for additional details about total ink coverage. (3) Adequately Dry Graphics Important Note! Inadequate drying can result in graphic failure including curling, increased shrinkage and adhesion failure, which are not covered under warranty. Always build enough time into your process to ensure adequate drying of the graphic. Poorly dried film may become soft and stretchy, and the adhesive may become too aggressive. This can cause difficulty when applying an overlaminate, rolling the graphic, and applying the film. See the ink's Instruction Bulletin for more details. B. Cutting The following are common cutting methods. See Instruction Bulletin 4.1 for details. For individual pieces, use one of these cutting methods. Hand cut Die cut Kiss cut Electronic cutter For multiple pieces, use one of these cutting methods. Guillotine Die cut (1) Minimum Cutting Heights Based on cutting and weeding evaluations that used Helvetica medium upper case, the recommended minimum cutting height for text is 1 inch (2.54 cm). Because of the differences in electronically-controlled cutting equipment and font characteristics, users should determine their own cutting and weeding capability. (2) Inside and Outside Corners For inside and outside corners of cut out letters and symbols, and the pointed end of stripes, cut the largest radius consistent with an acceptable appearance. This technique helps avoid stress cracking due to age, and lifting of pointed ends during maintenance. (3) Factors that Affect Cutting Quality and Ability Sharpness of the knife blade. Dull blades create a serrated look to the cut edge of the film scores the liner. Too little weight does not cut completely through the film and the adhesive. Excessive weight cuts the liner. It also causes the blade to drag, accelerating wear and eventually creating a serrated cut edge on the film. Temperature and relative humidity are minor considerations, but avoid extreme or rapidly fluctuating conditions. Store the film in the same environment as the cutting equipment. Consider the stroke width of characters, style of serifs or extensions, and small details of scanned or digitized artwork. The minimum recommended stroke width is inch (1.0 mm) when film is exposed to cleaning or other physical stress C. Application Tapes (1) When to Use Premasking Tape (2) When to Use Prespacing Tape As an application aid to increase stiffness, and prevent stretching and damage during application. Hold cut and weeded letters or graphics in registration after removing the film liner. Protect cut graphic parts from scratching or damage during application. Use when large amounts of liner are exposed. Product Bulletin PIJ3630-7

8 (3) How to Select a Tape Determine whether you want to premask the graphic or prespace film elements. Then locate the graphic protection on your graphic in the table below, and use the corresponding tape. See Instruction Bulletin 4.3 for complete details. EXAMPLE: If the film is protected by overlaminate 8519 and you want to premask the film, use premasking tape SCPM-3. If it is protected by clear 9720i, use premasking tape SCPM-44X. Graphic Protection Refer to the Warranty table to determine what graphic protection is approved for your graphic construction. None None 3619, i UV ink series Other ink 8518, 8519, 1920DR UV Application Tape only series 8520, 8915 Premasking SCPM-3 Prespacing SCPS-2 Premasking SCPM-44X Prespacing SCPS-53X NR= Prespacing and/or premasking it not recommended when using this graphic protection option. 9. Application and Installation For application by hand, the detergent and water application method is recommended for this pressure-sensitive film. Dry application by hand may leave some dark streaks or bubbles that could be visible in transmitted light. For roll application, the dry method is acceptable. 10. Maintenance and Cleaning Use a cleaner designed for high-quality painted surfaces. The cleaner must be wet, nonabrasive, without strong solvents, and have a ph value between 3 and 11 (neither strongly acidic nor strongly alkaline.) Refer to Instruction Bulletin 6.5 for general maintenance and cleaning information. 11. Shelf Life, Storage and Shipping A. Shelf Life Total shelf life: 3 years from the date of manufacture on the original box. Up to 3 years unprocessed, OR process within 2 years and then apply within 1 year of processing. B. Storage Conditions 40 to 100 F (4 to 38 C) Out of sunlight Clean dry area Original container Bring the film to print room temperature before using C. Shipping Finished Graphics Flat, or rolled printed side out on 6 inch (15 cm) or larger core. This helps prevent the liner and, if used, the application tape from popping off. 12. Health and Safety! CAUTION When handling any chemical products, read the manufacturers' container labels and the Material Safety Data Sheets (MSDS) for important health, safety and environmental information. To obtain MSDS sheets for 3M products go to 3M.com/MSDS, or by mail or in case of an emergency, call or When using any equipment, always follow the manufacturers' instructions for safe operation. Product Bulletin PIJ3630-8

9 13. 3M Related Literature Before starting any job, be sure you have the most current Product and Instruction Bulletins. The information in 3M Product and Instruction Bulletins is subject to change. Current Bulletins are available at 3Mgraphics.com. The following applicable Bulletins provide information and processes you need to properly make the graphics described in this Bulletin. Additional Bulletins may be needed as indicated in the 3M Related Literature section of other 3M components you use. Bulletin types: PB = Product Bulletin; PB-IB = Product & Instruction Bulletin; IB = Instruction Bulletin Subject Type Bulletin No. 3M Piezo Inkjet Ink Series 1500v2 PB-IB M Piezo Inkjet Ink Series 4400 PB-IB M Piezo Inkjet Ink Series 4800 PB-IB M Piezo Inkjet Ink Series 5500 PB-IB M Piezo Inkjet Ink Series 6200 PB-IB M Piezo Inkjet Ink Series 2200UV PB-IB 2200UV 3M Piezo Inkjet Ink Series 2600UVv2 PB-IB 2600UV 3M Piezo Inkjet Ink Series 2700UV PB-IB 2700UV 3M Piezo Inkjet Ink Series 2800UV PB-IB 2800UV 3M Piezo Inkjet Ink Series 5400UV PB-IB 5400UV Mimaki Ink Series LF-200 PB-IB LF200 3M Graphic Protection Products PB GP-1 3M Screen Print Gloss Clear 1920DR - Applying screen printing clear 1920DR PB IB M Screen Print UV Clears 9720i, 9720UV, 9730UV PB-IB Clears M Panaflex Awning and Sign Facing 945GPS PB 945 3M Panagraphics III Wide-Width Flexible Substrate - Application of 3M pressure sensitive films to Panagraphics substrate PB IB P M Light Management Films from Series 3635 PB 3635 Cold roll lamination IB 4.22 Scoring and cutting IB 4.1 Using 3M application tapes; premasking and prespacing for films IB 4.3 Making backlit signs with 3M digitally imaged graphics IB 4.26 Application, substrate selection, preparation and application techniques IB 5.1 Application, general procedures for indoor and outdoor dry applications IB 5.5 Application, wet method for translucent screen printed and cut graphics IB 5.7 Application, special applications and vehicles IB 5.4 Storage, handling, maintenance, removal IB 6.5 3M Graphics Center Warranty Brochure go to Warranties 3M, MCS, Panaflex, Panagraphics and Scotchcal are trademarks of 3M Company. EFI is a trademark and VUTEk is a registered trademark of EFI Inc.; All other trademarks are the property of their respective owners. 14. Bulletin Change Summary New Compatible Products: Added HP Scitex LX600 & LX800 and HP 3M LX600 Specialty LATEX inks; Added Mimaki JFX-1631 and JFC-1615R printers for ink series LF-200. Discontinued ink series 6000 and 6800 and films. Film RG is available for purchase and use with only a 3M Basic Product Warranty on a customer test and approve basis. Product Bulletin PIJ3630-9

10 Commercial Graphics Division 3M Center, Building E-04 PO Box St. Paul, MN USA General Info Technical Info Fax M Canada P.O. Box 5757 London, Ontario Canada N6A 4T Fax M México, S.A. de C.V Av. Santa Fe No. 55 Col. Santa Fe, Del. Alvaro Obregón México, D.F Fax M Puerto Rico, Inc. Puerto Rico Industrial Park 350 Chardon Avenue, Suite 1100 San Juan PR Fax M All rights reserved. Product Bulletin PIJ