3D Scanning Guide. 0. Login. I. Startup
|
|
- Bertram McKenzie
- 6 years ago
- Views:
Transcription
1 3D Scanning Guide UTSOA has a Konica Minolta Vivid 910 3D non-contact digitizing system. This scanner is located in the digital fabrication section of the technology lab in Sutton Hall It is free for use by all student in the school of architecture. The Vivid 910 system is capable of scanning over 300,000 data points with very high accuracy in under one minute. The unit is also equipped with an automated rotary stage for 360 degree captures and will overlay captured geometry with textures captured from the camera lens of the unit. - See more at: 0. Login Ask a TA at the SOA-Technology Desk to log into the computer with the Admin account. I. Startup 1. Make sure that the scanner is turned on before the computer. If the scanner is turned off (or not recognized), reboot the computer with the scanner on. 2. Launch Geomagic Studio 2012 from the desktop. 3. When the welcome screen comes up, select Scan. 4. When the Minolta Vivid Plugin Tray comes up on the left, click the camera button.
2 Note: If you lose the Minolta tray at any point, select the Hardware tab at the top of the window and click the Minolta Vivid button. II. Place Object for Scanning: 1. Select 'Show/Hide Live Image Window", then click the 'stream' check box. You can now see what the scanner sees in the window. 2. Place object in optimal position with appropriate lens (see object and placement guidelines below). 3. Uncheck the "Stream" box. If it is on during calibration, the software will crash. III. Calibrate Rotational Axis: 1. Place the calibration chart on the turntable. Make sure that the black stripe is at the center of rotation and that the wooden top is relatively centered on the turntable base. (You will need to reach under the wooden top to check if it s centered on the turntable.)
3 2. Expand the Turntable Control Dialogue in the Minolta Tray and select 'Calibrate'. 3. If calibration is successful, you should see an image like the one below in the Live Window.
4 4. Place the object back on the turntable and recheck Stream. As you place the object, do not move the tripod, table or turntable as this would invalidate the calibration. IV. Check Settings Your settings should be similar to the image below. Camera Control: Auto Focus, Auto Intensity and Auto Brightness should all be checked Advanced Camera Control: Do not change these settings. Scanning Options: Name You can name your scan here. Scan Angle Filter Default of 75 is fine for most cases. This is a decimal field (0 to 90 degrees) that specifies the maximum divergence from perpendicular of surfaces whose points are to be captured. Turntable Control: Turntable and Com Port - Use settings shown at left. Scan mode: Single - Takes a single scan from one angle. Continuous (recommended setting) After the first scan, which will require confirmation, the scanner will automatically continue scanning, rotating the object by the number of degrees specified in the Step box between each scan. Multishot Like Continuous mode, but requires you to click Scan after each step. Step: Specifies the number of degrees the object will be rotated between scans. V. Scan Object (using Continuous mode) 1. Under Scanning, click Scan. This will scan the object and place the first scan in the Live Window.
5 2. After the first scan is verified (meaning you have checked that good data was collected), click the Store button. The scanner will continue through the rest of the scans automatically. NOTE: If your scan looks like a radial array of object segments as in the image below, go back to the turntable calibration step.
6 3. Click 'OK' on the Minolta Vivid Dialogue. This will close the plug-in and return you to the application with your scanned data. VI. Merge and Save The Geomagic software has a number of options for editing your model that are not covered in this guide. However-- **If you want to make any changes or adjustments to your scan, do so before moving on to the next step ** 1. Select all of your scans under the model manager, and click "Merge" under the Points tab.
7 2. Click "OK" under Merge Scans. 3. Select your merged scan under the model manager, and click the Save button. You can save your model as an.stl file (recommended) or another file format, depending on which program you will use to continue working on your model. NOTE: AutoCAD, 3DS Max, Rhino & other common modeling software cannot handle six-figure meshes - if you are bringing a single scan into a model - we usually recommend ~25k polygons (see Max Triangles in the dialogue box above) - if you need greater detail you can go up to perhaps 75k, if you want smaller files, you can reduce the number significantly. Object guide:
8 The scanner works best with matte-white objects. Black, glossy, or transparent objects will have problems scanning or may not scan at all. Using corn starch, white spray paint, epsom salt spray (from the 3d print process), or 'spray developer' are ways that object can be treated to provide quality scanning. In order for a surface to be scanned it must be visible simultaneously to the optical lens (upper aperture) and the laser lens (lower aperture) on the 3D scanner. With the 'medium' lens the scanner and current setup the scanner is ready to scan objects ranging from about 3"-cubed to about 12"-cubed. (Using alternate lenses, this range can be extended down to 0.5"-cubed or up to 36"-cubed object volumes. For alternate lens installation see the computer lab service desk.)
Minolta Scanner Plugin
Minolta Scanner Plugin For a list of Minolta digitizers and Geomagic software products with which this plugin is compatible, see Release Notes for Geomagic Minolta Plugin 7.6.0.3. Copyright 2005, Raindrop
More informationFire CR Calibration Guide
1 Fire CR Calibration Guide This reference guide will guide you through the steps to complete the calibration for the Fire CR.. Getting Started: 1. Click on the Opal Icon on the Desktop. Figure 1 2. Once
More informationEinScan-SE. Desktop 3D Scanner. User Manual
EinScan-SE Desktop 3D Scanner User Manual Catalog 1. 2. 3. 4. 5. 6. 7. 8. 1.1. 1.2. 1.3. 1.1. 1.2. 1.1. 1.2. 1.3. 1.1. 1.2. Device List and Specification... 2 Device List... 3 Specification Parameter...
More informationYou can easily print images using the Capture NX print function. Here we will explain the process for printing
Printing - Print Size Request How do you print images to fit on particular paper sizes. Response You can easily print images using the Capture NX print function. Here we will explain the process for printing
More informationDAVID SLS-1. Getting Started Guide
DAVID SLS-1 Getting Started Guide Version 3.7 DAVID Vision Systems GmbH Rudolf-Diesel-Str. 2a D-56070 Koblenz Germany Phone: +49(0)261 983 497-70 Fax: +49(0)261 983 497-77 Mail: service@david-vision-systems.de
More informationR I T. Title: Wyko RST Plus. Semiconductor & Microsystems Fabrication Laboratory Revision: A Rev Date: 05/23/06 1 SCOPE 2 REFERENCE DOCUMENTS
Approved by: Process Engineer / / / / Equipment Engineer 1 SCOPE The purpose of this document is to detail the use of the Wyko RST Plus. All users are expected to have read and understood this document.
More informationUser Manual Of Einscan-Pro. Brief Introduction
User Manual Of Einscan-Pro Brief Introduction 1. PC Configuration 2. Software interface 3. Calibration 4. Fix Scan 5. Handheld HD Scan 6. Handheld Rapid Scan 7.FAQ PC Configuration System Requirement:Before
More informationEinScan-Pro+ Multi-Functional Handheld 3D Scanner. User Manual
EinScan-Pro+ Multi-Functional Handheld 3D Scanner User Manual Catalog Device List and Specification... 3 Device List... 4 Specification Parameter... 5 Installation Notes... 6 Hardware Installation... 7
More informationQUICKSTART GUIDE: WIDEFIELD HWF1 Zeiss Cell Observer Live Cell Imaging System (HAMMERSMITH, L BLOCK, ROOM 314) Imperial College London
Imperial College London Facility for Imaging by Light Microscopy QUICKSTART GUIDE: WIDEFIELD HWF1 Zeiss Cell Observer Live Cell Imaging System (HAMMERSMITH, L BLOCK, ROOM 314) Observing Life As It Happens
More informationUser Manual Of Einscan-Pro. Brief Introduction
User Manual Of Einscan-Pro Brief Introduction 1. PC Configuration 2. Software interface 3. Calibration 4. Fix Scan 5. Handheld HD Scan 6. Handheld Rapid Scan 7.FAQ PC Configuration System Requirement:Before
More informationOlympus LEXT OLS 4000 Confocal Laser Microscope
Olympus LEXT OLS 4000 Confocal Laser Microscope The Olympus LEXT OLS4000 is a confocal microscope capable of taking high-resolution 3D images. The magnification (Optical and Digital) of this microscope
More informationProcedures for the Use of the PointGrey Flea3 FireWire Camera and ImageJ *
Procedures for the Use of the PointGrey Flea3 FireWire Camera and ImageJ * * Although the following procedures are given for the Free Fall experiment, you can utilize the camera adjustments and settings,
More informationContents STARTUP MICROSCOPE CONTROLS CAMERA CONTROLS SOFTWARE CONTROLS EXPOSURE AND CONTRAST MONOCHROME IMAGE HANDLING
Operations Guide Contents STARTUP MICROSCOPE CONTROLS CAMERA CONTROLS SOFTWARE CONTROLS EXPOSURE AND CONTRAST MONOCHROME IMAGE HANDLING Nikon Eclipse 90i Operations Guide STARTUP Startup Powering Up Fluorescence
More informationMC3 Motion Control System Shutter Stream Quickstart
MC3 Motion Control System Shutter Stream Quickstart Revised 7/6/2016 Carousel USA 6370 N. Irwindale Rd. Irwindale, CA 91702 www.carousel-usa.com Proprietary Information Carousel USA has proprietary rights
More informationInserting and Creating ImagesChapter1:
Inserting and Creating ImagesChapter1: Chapter 1 In this chapter, you learn to work with raster images, including inserting and managing existing images and creating new ones. By scanning paper drawings
More information3D Scanning with Artec Studio 11 Professional
Digital Media Tutorial Witten by Dan Staffieri 3D Scanning with Artec Studio 11 Professional 1) Open Artec Studio 11 Professional 2) Press the Preview button or press the Artec scanner s toggle switch
More information12 x 12 anti-glare screen provides a clear, detailed view of your microform.
MS6000 MKII Microform Scanner. High-resolution viewing, with auto imaging and optional trimming and masking. Dual scan and print output at a single touch. The ability to reads on screen, print on paper,
More informationTitle: Leica SP5 Confocal User Manual
Title: Leica SP5 Confocal User Manual Date of first issue: 23/10/2015 Date of review: Version: Admin For assistance or to report an issue Office: CG07 or 05 Email: Igmm-imaginghelpdesk@igmm.ed.ac.uk Website:
More informationKoPa Scanner. User's Manual A99. Ver 1.0. SHENZHEN OSTEC OPTO-ELECTRONIC TECHNOLOGY CO.,LTD.
KoPa Scanner A99 User's Manual Ver 1.0 SHENZHEN OSTEC OPTO-ELECTRONIC TECHNOLOGY CO.,LTD. http://www.ostec.com.cn Content Chapter 1 Start... 1 1.1 Safety Warnings and Precautions... 1 1.2 Installation
More informationistar Panoramas for HDS Point Clouds Hugh Anderson Illustrations, descriptions and technical specification are not binding and may change.
istar Panoramas for HDS Point Clouds istar Panoramas for HDS Point Clouds Why use istar Panoramas for HDS Point Clouds Taking the Photographs Fitting the Panorama with ColourCloud Creating the Equirectangular
More informationDiaInspect-P. Operating manual. Version Page 1
DiaInspect-P Operating manual Version 8.1.9 Page 1 1. Application of the device... 3 2. Operating concept... 3 2.1. Hardware... 4 2.2. Software... 5 2.3. Data archiving... 6 3. Functions in operators mode...
More informationShadowtracker User Manual
Shadowtracker User Manual Shadowtracker is a helidon housed at the University of Oregon s Baker Lighting Lab College of Architecture and Allied Arts Department of Architecture Designed and constructed
More informationMotion Blur with Mental Ray
Motion Blur with Mental Ray In this tutorial we are going to take a look at the settings and what they do for us in using Motion Blur with the Mental Ray renderer that comes with 3D Studio. For this little
More informationLeica SP8 TCS Users Manual
Version : 07/08/0 Leica SP8 TCS Users Manual Start up:. Turn the PC Microscope, Scanner Power, Laser Power, and the Laser Emission key to on (bottom right of desk).. Turn on the fluorescent lamp (top left
More informationEinScan-Pro+ Multi-Functional Handheld 3D Scanner. User Manual
EinScan-Pro+ Multi-Functional Handheld 3D Scanner User Manual Catalog Device List and Specification... 3 Device List... 4 Specification Parameter... 5 Installation Notes... 6 2.1. Hardware Installation...
More informationUser Manual SCANIFY F3D2001. Version 1.0. Revision Date:
User Manual SCANIFY F3D2001 Version 1.0 Revision Date: 2015.01.02 Contents SCANIFY Profile 2 Set-up 3 - Registering your device and locating your serial number - Setting up your scanner 3 Taking a scan
More informationRANGEVISION. SMART ScanCenter
RANGEVISION SMART ScanCenter 2016.2 Introduction Technical specifications System requirements Preparing to work Package contents Installing software and drivers Scanner conection Scanner assembly Connecting
More informationPLEASE WEAR GLOVES. NEVER TOUCH THE RESIN (EVEN WITH GLOVED HANDS). BE CAREFUL: RESIN GETS EVERYWHERE.
FORM 2 TUTORIAL PLEASE KEEP THE FORM 2 AREA CLEAN. PLEASE WEAR GLOVES. NEVER TOUCH THE RESIN (EVEN WITH GLOVED HANDS). BE CAREFUL: RESIN GETS EVERYWHERE. TABLE OF CONTENTS STEP 1: HAVE YOUR.STL or.obj
More informationAs an ENERGY STAR Program Participant, the manufacturer has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
C5150/C5200ne/C5200n Technical Reference, Macintosh 59351301 Rev 1.2 August 2005 Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. The manufacturer
More informationInformation & Instructions
KEY FEATURES 1. USB 3.0 For the Fastest Transfer Rates Up to 10X faster than regular USB 2.0 connections (also USB 2.0 compatible) 2. High Resolution 4.2 MegaPixels resolution gives accurate profile measurements
More informationImage-Pro Plus 7.0 Product Note
Image-Pro Plus 7.0 Product Note Automated Microscope Configuration Introduction Cameras, software, shutters, stages, objectives, filters, turrets there are a lot of components in an automated microscopy
More informationKurzweil Adaptive Technology Lab - FAQs.
Kurzweil 1000 Adaptive Technology Lab - FAQs. Q. What is Kurzweil 1000? A. Kurzweil 1000 is a software program that scans paper text documents, converts scanned documents to digital text, and reads digital
More informationQUICKSTART GUIDE: WIDEFIELD WF3 Zeiss Cell Observer Live Cell Imaging System (SAF, ROOM 409) Imperial College London
Imperial College London Facility for Imaging by Light Microscopy QUICKSTART GUIDE: WIDEFIELD WF3 Zeiss Cell Observer Live Cell Imaging System (SAF, ROOM 409) Observing Life As It Happens Startup procedure...
More informationConfocal Application Notes Vol. 5 July 2010
Tile Scan Prepared by Myriam Gastard, PhD Application and Technical Support Group, Leica Microsystems, Inc. In this issue of our Confocal Application Notes, proper set up of the Tile function enables you
More informationinphoto ID Canon and Olympus camera control software Automatic ID photography User Guide
inphoto ID Canon and Olympus camera control software Automatic ID photography User Guide 2006 Akond company 197342, Russia, St.-Petersburg, Serdobolskaya, 65a Phone/fax: +7(812)600-6918 Cell: +7(921)757-8319
More informationENSC 470/894 Lab 3 Version 6.0 (Nov. 19, 2015)
ENSC 470/894 Lab 3 Version 6.0 (Nov. 19, 2015) Purpose The purpose of the lab is (i) To measure the spot size and profile of the He-Ne laser beam and a laser pointer laser beam. (ii) To create a beam expander
More informationRANGEVISION. ScanCenter
RANGEVISION ScanCenter 2016.2 Introduction System requirements Technical specifications Preparing for work Package contents Installing software and drivers Setting up your computer for the work with the
More informationPASS Sample Size Software. These options specify the characteristics of the lines, labels, and tick marks along the X and Y axes.
Chapter 940 Introduction This section describes the options that are available for the appearance of a scatter plot. A set of all these options can be stored as a template file which can be retrieved later.
More informationHow to combine images in Photoshop
How to combine images in Photoshop In Photoshop, you can use multiple layers to combine images, but there are two other ways to create a single image from mulitple images. Create a panoramic image with
More informationLEICA TCS SP5 AOBS TANDEM USER MANUAL
LEICA TCS SP5 AOBS TANDEM USER MANUAL STARTING THE SYSTEM...2 THE LAS AF SOFTWARE...3 THE «ACQUIRE» MENU...5 CHOOSE AND CREATE A SETTING...6 THE CONTROL PANEL...8 THE DMI6000B MICROSCOPE...10 ACQUIRE ONE
More informationOPT3: Operating Procedure for Horiba Jobin Yvon LabRam Aramis Raman/PL System See LabSpec_6_2 General User Quick Start Guide on the computer desktop
OPT3: Operating Procedure for Horiba Jobin Yvon LabRam Aramis Raman/PL System See LabSpec_6_2 General User Quick Start Guide on the computer desktop 1. Log in usage using the SMIF web site 2. Turn power
More informationROTATING SYSTEM T-12, T-20, T-50, T- 150 USER MANUAL
ROTATING SYSTEM T-12, T-20, T-50, T- 150 USER MANUAL v. 1.11 released 12.02.2016 Table of contents Introduction to the Rotating System device 3 Device components 4 Technical characteristics 4 Compatibility
More informationBEAMAGE KEY FEATURES AVAILABLE MODELS. CMOS Beam Profiling Cameras
BEAM DIAGNOS TICS Beam Profiling Cameras KEY FEATURES SPECIAL PRODUCTS OEM DETECTORS THZ DETECTORS PHOTO DETECTORS HIGH POWER SOLUTIONS POWER DETECTORS ENERGY DETECTORS MONITORS AVAILABLE MODELS Beamage-3.0
More informationGetting started 1 System Requirements... 1 Software Installation... 2 Hardware Installation... 2 System Limitations and Tips on Scanning...
Contents Getting started 1 System Requirements......................... 1 Software Installation......................... 2 Hardware Installation........................ 2 System Limitations and Tips on
More informationThe Mobile CNC Measurement and 3D Scanning System. WENZEL ScanTec MobileScan3D
The Mobile CNC Measurement and 3D Scanning System WENZEL ScanTec MobileScan3D MobileScan3D What is it and how does it work? MobileScan3D is a truly mobile CNC laser scanning solution allowing fully automatic
More informationXYZscan User Manual ENG. XYZscan User Manual P 1
ENG XYZscan User Manual P 1 Declaration Limitation of Liability Clause Although we try to ensure that the manual and product functions are correct and stable, in no event shall XYZprinting be liable for
More informationInstruction Manual for HyperScan Spectrometer
August 2006 Version 1.1 Table of Contents Section Page 1 Hardware... 1 2 Mounting Procedure... 2 3 CCD Alignment... 6 4 Software... 7 5 Wiring Diagram... 19 1 HARDWARE While it is not necessary to have
More informationBruker Dimension Icon AFM Quick User s Guide
Bruker Dimension Icon AFM Quick User s Guide August 8 2014 GLA Contacts Jingjing Jiang (jjiang2@caltech.edu 626-616-6357) Xinghao Zhou (xzzhou@caltech.edu 626-375-0855) Bruker Tech Support (AFMSupport@bruker-nano.com
More informationHoriba LabRAM ARAMIS Raman Spectrometer Revision /28/2016 Page 1 of 11. Horiba Jobin-Yvon LabRAM Aramis - Raman Spectrometer
Page 1 of 11 Horiba Jobin-Yvon LabRAM Aramis - Raman Spectrometer The Aramis Raman system is a software selectable multi-wavelength Raman system with mapping capabilities with a 400mm monochromator and
More informationExercise 2-2. Four-Wire Transmitter (Optional) EXERCISE OBJECTIVE DISCUSSION OUTLINE. Ultrasonic level transmitter DISCUSSION
Exercise 2-2 Four-Wire Transmitter (Optional) EXERCISE OBJECTIVE Become familiar with HART point-to-point connection of a four-wire transmitter. DISCUSSION OUTLINE The Discussion of this exercise covers
More informationZeiss LSM 510 Confocor III Training Notes. Center for Cell Analysis & Modeling
Zeiss LSM 510 Confocor III Training Notes Center for Cell Analysis & Modeling Confocor 3 Start Up Go to System Module Turn on Main Switch, System/ PC, and Components Switches Do you need the arc lamp?
More informationDownloading a ROBOTC Sample Program
Downloading a ROBOTC Sample Program This document is a guide for downloading and running programs on the VEX Cortex using ROBOTC for Cortex 2.3 BETA. It is broken into four sections: Prerequisites, Downloading
More informationMityCAM-B2521 EPIX XCAP User s Guide
MityCAM-B2521 EPIX XCAP User s Guide (CT031 Revision 1) Page 1 of 13 60-000014 Contents 1 Installing Laptop Express Card... 3 2 Using the Camera in Single Camera Link mode (Laptop)... 3 3 Single Camera
More informationAirScope Spectrum Analyzer User s Manual
AirScope Spectrum Analyzer Manual Revision 1.0 October 2017 ESTeem Industrial Wireless Solutions Author: Date: Name: Eric P. Marske Title: Product Manager Approved by: Date: Name: Michael Eller Title:
More informationAdvanced Diploma in. Photoshop. Summary Notes
Advanced Diploma in Photoshop Summary Notes Suggested Set Up Workspace: Essentials or Custom Recommended: Ctrl Shift U Ctrl + T Menu Ctrl + I Ctrl + J Desaturate Free Transform Filter options Invert Duplicate
More informationTable of Contents. Chapter 1: Software Installation...1. Chapter 2: Running the Software II. Daily Practical Operation...10
Product Manual Table of Contents Chapter 1: Software Installation.................................1 Chapter 2: Running the Software............................... 2 I. The Initial Defining in Lock Management
More informationBruker Dimension Icon AFM Quick User s Guide
Bruker Dimension Icon AFM Quick User s Guide March 3, 2015 GLA Contacts Jingjing Jiang (jjiang2@caltech.edu 626-616-6357) Xinghao Zhou (xzzhou@caltech.edu 626-375-0855) Bruker Tech Support (AFMSupport@bruker-nano.com
More informationStitching distortion-free mosaic images for QWA using PTGui. Georg von Arx
Stitching distortion-free mosaic images for QWA using PTGui Georg von Arx Index A. Introduction and overview... 2 B. Taking microscopic images... 2 C. Installing PTGui... 3 D. Initial Setup... 3 E. Preparing
More informationFrom Raster to Vector: Make That Scanner Earn Its Keep!
December 2-5, 2003 MGM Grand Hotel Las Vegas From Raster to Vector: Make That Scanner Earn Its Keep! Felicia Provencal GD31-2 This class is an in-depth introduction to Autodesk Raster Design, formerly
More informationENG. XYZscan User Manual P 1
ENG XYZscan User Manual P 1 Declaration Limitation of Liability Clause Although we try to ensure that the manual and product functions are correct and stable, in no event shall XYZprinting be liable for
More informationScanGear CS-U 6.0. for CanoScan D646U Color Scanner. User s Guide
ScanGear CS-U 6.0 for CanoScan D646U Color Scanner User s Guide Copyright Notice Copyright 2000 Canon Inc. This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may
More informationVeterinary Digital X-Ray System Quick Start Guide
1 Veterinary Digital X-Ray System Quick Start Guide 2 SOPIX² X-Ray Sensors Quick Start Guide ***PERFORM THIS STEP BEFORE PLUGGING IN THE SENSOR*** Step 1 Load the CD: If you have already plugged in the
More informationOperating Procedures for MICROCT1 Nikon XTH 225 ST
Operating Procedures for MICROCT1 Nikon XTH 225 ST Ensuring System is Ready (go through to ensure all windows and tasks below have been completed either by you or someone else prior to mounting and scanning
More informationZeiss LSM 780 Protocol
Zeiss LSM 780 Protocol 1) System Startup F Please note the sign-up policy. You must inform the facility at least 24 hours beforehand if you can t come; otherwise, you will receive a charge for unused time.
More informationInstruction manual for T3DS software. Tool for THz Time-Domain Spectroscopy. Release 4.0
Instruction manual for T3DS software Release 4.0 Table of contents 0. Setup... 3 1. Start-up... 5 2. Input parameters and delay line control... 6 3. Slow scan measurement... 8 4. Fast scan measurement...
More informationBEAMAGE-3.0 KEY FEATURES BEAM DIAGNOSTICS AVAILABLE MODELS MAIN FUNCTIONS SEE ALSO ACCESSORIES. CMOS Beam Profiling Cameras
BEAM DIAGNOSTICS BEAM DIAGNOSTICS SPECIAL PRODUCTS OEM DETECTORS THZ DETECTORS PHOTO DETECTORS HIGH POWER DETECTORS POWER DETECTORS ENERGY DETECTORS MONITORS CMOS Beam Profiling Cameras AVAILABLE MODELS
More informationScanning Procedure Using SilverFast Ai Software (6.6.1r2b) 1
last modified 6.16.2015 Scanning Procedure Using SilverFast Ai Software (6.6.1r2b) 1 PREP In scanner notebook, fill out Incoming Checklist column on a Scanner Equipment Checklist sheet. Use flash drive
More informationCell Biology and Bioimaging Core
Cell Biology and Bioimaging Core Leica TCS SP5 Operating Instructions Starting up the instrument 1. First, log in the log book located on the confocal desk. Include your name, your lab s PI, an account
More informationPANalytical X pert Pro Gazing Incidence X-ray Reflectivity User Manual (Version: )
University of Minnesota College of Science and Engineering Characterization Facility PANalytical X pert Pro Gazing Incidence X-ray Reflectivity User Manual (Version: 2012.10.17) The following instructions
More informationAxioscan - Startup. 1. Turn on the Axioscan (button to the left) and turn on the computer. 2. Log on and start the ZEN Blue software from the desktop
Axioscan - Startup 1. Turn on the Axioscan (button to the left) and turn on the computer 2. Log on and start the ZEN Blue software from the desktop 3. Press ZEN slidescan and Start System 4. Start by changing
More informationERS KEY FEATURES BEAM DIAGNOSTICS MAIN FUNCTIONS AVAILABLE MODEL. CMOS Beam Profiling Camera. 1 USB 3.0 for the Fastest Transfer Rates
POWER DETECTORS ENERGY DETECTORS MONITORS SPECIAL PRODUCTS OEM DETECTORS THZ DETECTORS PHOTO DETECTORS HIGH POWER DETECTORS CAMERA PROFIL- CMOS Beam Profiling Camera KEY FEATURES ERS 1 USB 3.0 for the
More informationPaperCut Toshiba Eraser Embedded Manual
PaperCut Toshiba Eraser Embedded Manual Contents 1 Overview... 3 2 Installation... 5 2.1 Requirements... 5 2.1.1 Supported Devices... 5 2.2 Setup Procedure... 5 2.2.1 Verify Access to the Toshiba Administrative
More informationUniversal Camera Registration User Guide for ILS 9.75 & 12.75
User Guide for ILS 9.75 & 12.75 www.ulsinc.com Overview Camera Registration allows the laser system to automate the alignment of a vector path with the material for the purpose of tightening process control
More informationTM5. Guide Book. Hardware Version: 2.00 Software Version: 1.62
TM5 Guide Book Hardware Version: 2.00 Software Version: 1.62 ii Release Date : 2017-07-10 The information contained herein is the property of Techman Robot Corporation (hereinafter referred to as the Corporation).
More informationCombo Scanner. User Manual
Combo Scanner User Manual I. Unpack the Combo Scanner Backlight Holder Combo Scanner Business card Fixture Photo/Business Card Holder User Manual Quick Installation Guide Note This Combo Scanner supports
More informationEagleSoft Instructions for using Scanner Interface Version: 11.0 Date Created: 9/1/04 Last Modified: 9/3/04 Filename: 11 Scanner Interface.
EagleSoft Instructions for using Scanner Interface Version: 11.0 Date Created: 9/1/04 Last Modified: 9/3/04 Filename: 11 Scanner Interface.doc Required materials: TWAIN compliant Flatbed Scanner Required
More informationRachel
http://gmv.cast.uark.edu A Method Store for Advanced Survey and Modeling Technologies Mon, 01 Apr 2013 03:29:18 +0000 en-us hourly 1 http://wordpress.org/?v=3.5.1 http://gmv.cast.uark.edu/scanning/guide-to-leveling-andaligning-the-breuckmann-tripod-and-smartscan-he-for-calibration/
More informationHARDWARE SETUP GUIDE. 1 P age
HARDWARE SETUP GUIDE 1 P age INTRODUCTION Welcome to Fundamental Surgery TM the home of innovative Virtual Reality surgical simulations with haptic feedback delivered on low-cost hardware. You will shortly
More informationLSM 510 Meta Training Notes
LSM 510 Meta Training Notes Turning on the system Turn on X-Cite power supply. This supplies light for epifluorescence for viewing your samples through the microscope. Turn on the remote control switch.
More informationSteamVR Unity Plugin Quickstart Guide
The SteamVR Unity plugin comes in three different versions depending on which version of Unity is used to download it. 1) v4 - For use with Unity version 4.x (tested going back to 4.6.8f1) 2) v5 - For
More informationThings to check before start-up.
Byeong Cha Page 1 11/24/2009 Manual for Leica SP2 Confocal Microscope Enter you name, the date, the time, and the account number in the user log book. Things to check before start-up. Make sure that your
More informationLSM 510 Training Notes
LSM 510 Training Notes Turning on the system Turn on the arc lamp, found on the bench top left of the microscope. This supplies light for epifluorescence for viewing your samples through the microscope.
More informationSetup and Walk Through Guide Orion for Clubs Orion at Home
Setup and Walk Through Guide Orion for Clubs Orion at Home Shooter s Technology LLC Copyright by Shooter s Technology LLC, All Rights Reserved Version 2.5 September 14, 2018 Welcome to the Orion Scoring
More informationZeiss LSM 880 Protocol
Zeiss LSM 880 Protocol 1) System Startup Please note put sign-up policy. You must inform the facility at least 24 hours beforehand if you can t come; otherwise, you will receive a charge for unused time.
More informationHartmann Sensor Manual
Hartmann Sensor Manual 2021 Girard Blvd. Suite 150 Albuquerque, NM 87106 (505) 245-9970 x184 www.aos-llc.com 1 Table of Contents 1 Introduction... 3 1.1 Device Operation... 3 1.2 Limitations of Hartmann
More informationGlassSpection User Guide
i GlassSpection User Guide GlassSpection User Guide v1.1a January2011 ii Support: Support for GlassSpection is available from Pyramid Imaging. Send any questions or test images you want us to evaluate
More informationThe operation manual of spotlight 300 IR microscope
The operation manual of spotlight 300 IR microscope Make sure there is no sample under the microscope and then click spotlight on the desktop to open the software. You can do imaging with the image mode
More informationBeamPro 3.0 Series User Manual Revision WARRANTY
a BeamPro 3.0 Series User Manual Revision 9.0 1 WARRANTY The Edmund Optics BeamPro 3.0 series beam profiler carries a one-year warranty (from date of shipment) against material and/or workmanship defects,
More informationLabel Studio Quick Start Guide
Label Studio Quick Start Guide Overview The goal of the LabelStudio program is to help you layout and manage bulk jobs containing a mix of different logos, that all require a specified quanity. LabelStudio
More informationMEDIA CONVERSION PROJECT: DIGITIZING HISTORIC PHOTOS
MEDIA CONVERSION PROJECT: DIGITIZING HISTORIC PHOTOS What you need to know: Basic understanding of a computer What you need: Computer Epson Perfection V550 Scanner (available in the Southglenn and Smoky
More informationStandard Operating Procedure of Atomic Force Microscope (Anasys afm+)
Standard Operating Procedure of Atomic Force Microscope (Anasys afm+) The Anasys Instruments afm+ system incorporates an Atomic Force Microscope which can scan the sample in the contact mode and generate
More informationAPPLICATIONS FOR TELECENTRIC LIGHTING
APPLICATIONS FOR TELECENTRIC LIGHTING Telecentric lenses used in combination with telecentric lighting provide the most accurate results for measurement of object shapes and geometries. They make attributes
More informationWALLY ROTARY ENCODER. USER MANUAL v. 1.0
WALLY ROTARY ENCODER USER MANUAL v. 1.0 1.MEASUREMENTS ANGULAR POSITIONING a. General Description The angular positioning measurements are performed with the use of the Wally rotary encoder. This measurement
More informationZeiss 780 Training Notes
Zeiss 780 Training Notes Turn on Main Switch, System PC and Components Switches 780 Start up sequence Do you need the argon laser (458, 488, 514 nm lines)? Yes Turn on the laser s main power switch and
More informationENSC 470/894 Lab 1 V1.4 (Oct )
ENSC 470/894 Lab 1 V1.4 (Oct. 29 2010) Introduction: Lab 1 is designed to give students basic experience in optics. In the lab you will set up lenses on an optical table, with a LCD screen pattern as the
More informationCALIBRATION MANUAL. Version Author: Robbie Dowling Lloyd Laney
Version 1.0-1012 Author: Robbie Dowling Lloyd Laney 2012 by VirTra Inc. All Rights Reserved. VirTra, the VirTra logo are either registered trademarks or trademarks of VirTra in the United States and/or
More informationHARDWARE SETUP GUIDE. 1 P age
HARDWARE SETUP GUIDE 1 P age INTRODUCTION Welcome to Fundamental Surgery TM the home of innovative Virtual Reality surgical simulations with haptic feedback delivered on low-cost hardware. You will shortly
More informationNikon AZ100. Laser Scanning Macro Confocal Microscope. Jordan Briscoe Adam Fries Kyle Marchuk Kaitlin Corbin. May 2017.
Nikon AZ100 Laser Scanning Macro Confocal Microscope Jordan Briscoe Adam Fries Kyle Marchuk Kaitlin Corbin May 2017 Contents 1 Introduction 2 2 Hardware - Startup 2 3 Software/Operation 4 3.1 Multidimensional
More informationAgilEye Manual Version 2.0 February 28, 2007
AgilEye Manual Version 2.0 February 28, 2007 1717 Louisiana NE Suite 202 Albuquerque, NM 87110 (505) 268-4742 support@agiloptics.com 2 (505) 268-4742 v. 2.0 February 07, 2007 3 Introduction AgilEye Wavefront
More informationThe CReSIS Anechoic Chamber is located at: The University of Kansas. M2SEC building W 15 th St. Lawrence, KS
The CReSIS Anechoic Chamber is located at: The University of Kansas M2SEC building 1536 W 15 th St Lawrence, KS 66045 Pattern Manual Antenna radiation pattern measurement 1. To open EMQuest, right click
More information