Processing and. Photography. Printing

Size: px

Start display at page:

Download "Processing and. Photography. Printing"

Shanna Gertrude Ferguson
5 years ago
Views:

1 Processing and Photography Printing

2 Darkroom Layout Divided into dry area and wet area Need good workflow between the two Dry bench consists of enlarger photographic paper multigrade filters contact printer easel film Wet bench has trays of chemicals to process and wash the prints Two areas should be kept separate wet fingers can ruin negatives or printing papers for health and safety as water and electricity should be kept apart

3 Darkroom Layout 1. WHITE LIGHT 2. CONTACT PRINTING 3. ENLARGER S NEGATIVE CARRIER 4. ENLARGER 5. FOCUSING MAGNIFIER 6. EASEL 7. TIMER 8. DEVELOPER, STOP BATH & FIXER TRAYS 9. BOTTLES 10.PROCESSING TANK 11.FILM 12.SAFELIGHT

4 Basic Darkroom Equipment DRY BENCH Enlarger with lens Enlarger timer Easel Contact printer Focus finder (optional) Blower brush Printing filter kit Photographic paper Scissors or small guillotine 2 x A4 size card WET BENCH Set of trays Tongs Wash tray and hoses Clock 3 x measuring beaker Film and paper process chemicals A darkroom requires both a safelight and a white light source. Darkroom bulbs which can be plugged into an existing socket are available from photographic suppliers. You need at least 2 safelights and one should be above the dry area the other near the wet bench. The white light allows you to evaluate your work. Process trays should be 3 different colours labelled according to the chemicals they will contain (developer; stop bath; fix). Same for tongs and beakers. Contamination can badly affect your results using dedicated containers prevents this. (Wash everything after use too)

5 The entire process

6 Black & White Negative Processing Processing Equipment Requirements Developing tank and reels Thermometer Scissors 3 x 1 litre (2 pint) jugs Negative developer Stop bath Fix Hypo clearing agent Wetting agent Darkroom clock/timer Film wiper or chamois leather

Loading Film Exposed film is loaded onto the processing reel IN COMPLETE DARKNESS (no safelight) PRACTICE THE PROCESS WITH UNWANTED FILM IN THE LIGHT Lay out tank, reel, lids, reels reel rod and

7 Loading Film Exposed film is loaded onto the processing reel IN COMPLETE DARKNESS (no safelight) PRACTICE THE PROCESS WITH UNWANTED FILM IN THE LIGHT Lay out tank, reel, lids, reels reel rod and scissors so you know where they are and can find them in the dark Remove the exposed film cassette from camera. If leader tongue is still visible, cut it off so end of film is straight (b) Make sure reel is completely dry (hard to load if wet) Ensure the 2 small flag indicators are opposite one another Close the door, switch off the lights If you already cut off the film tongue you can load immediately, if it is in the film case, break open the case, feel for the tongue and cut it off with scissors Guide the film under the two flag indicators (c) and over the ball bearings. Gently pull the film onto the reel. Once you have threaded about 1 (2.5cm) it is safe to rotate the reel slowly (thumbs on flags) you will feel the film slip past your fingers (d) Continue rotating until the film cassette end prevent further winding (keeping thumbs on flags throughout to prevent film slipping off the reel edge) Cut off the cassette and rotate reel to load film end

Loading Film Insert the reel rod through the centre of the reel and put in the tank (e) Ensure that the flattened disc end fits into the slot at the bottom of the tank Put on the tank s lid With the

8 Loading Film Insert the reel rod through the centre of the reel and put in the tank (e) Ensure that the flattened disc end fits into the slot at the bottom of the tank Put on the tank s lid With the lid securely closed the film is now shielded from the light so you can turn on the light It is possible to load film into developing tanks inside a photographer s lightproof changing bag, in which case you can leave the light on but you are still working just by touch

Processing the film - 1 Fill measuring jug with 1 litre water @ 20 C (68 F) temperature is important In 2 nd jug measure required amount of developer; add the appropriate amount of water @ 20 C for

9 Processing the film - 1 Fill measuring jug with 1 litre 20 C (68 F) temperature is important In 2 nd jug measure required amount of developer; add the appropriate amount of 20 C for the number of films being developed. Pour the remaining water into the developing tank to pre-wet the film (ensures film at correct temp; ensures all film will get the chemical soln at the same time; washes off any dust) Close the upper lid of the tank Invert the tank twice; tap it gently on the wet bench (=agitation) leave to stand for seconds Remove the upper lid and pour away the water

Processing the film - 2 Set the dark room clock to the developing time (according to chart provided with the chemicals) Pour the developer into the tank and begin timing For the first 30 seconds

10 Processing the film - 2 Set the dark room clock to the developing time (according to chart provided with the chemicals) Pour the developer into the tank and begin timing For the first 30 seconds agitate the tank continuously, after this invert the tank and tap on the bench once every 30 secs for the rest of the developing time At the end of the time remove the tank s upper lid and pour the soln down the sink. Pour in the stop bath solution. Replace lid, agitate for 10 secs then stand. Pour stop bath soln down the sink after 30 secs and add the fixing bath soln. Fixing takes 2-4 mins depending on the brand you are using Agitate for 10 secs then one inversion and one tap every minute Pour fix into storage bottle and wash the film in running water for 10 minutes. It is important to remove all residue of chemical from the film (some tanks have a special tap fitting to make washing easy)

Processing the film - 3 At the end of the washing add a drop of wetting agent to the developing tank. Swirl the reel around in the tank making sure the agent is well mixed in the water.

11 Processing the film - 3 At the end of the washing add a drop of wetting agent to the developing tank. Swirl the reel around in the tank making sure the agent is well mixed in the water. Remove reel from tank and the film from the reel taking great care as the emulsion is still soft and easily scratched until it is dry Carefully wipe down the film with a wet softened chamois leather or special film wipers Hang the film up to dry (20-60 mins) dependent on temperature and whether using drying cupboard DO NOT EXAMINE THE NEGATIVES UNTIL THEY ARE DRY AS THEY ARE STILL VULNERABLE TO DAMAGE & DUST Once dry cut them into strips of six and immediately place in negative sleeves you can now safely view them

12 Printing the Negatives 2 types of photographic paper Resin coated (RC) Fibre based (FB) Both come with different surfaces glossy, matt, semi-mat etc Best to use RC paper to start with as it is cheaper, faster and less susceptible to chemical staining. Usually best to start with glossy paper Fibre based papers produce rich tones and are used for exhibition quality photographs

20 x 24cm (8x10 ) paper Requirements Contact printer

13 Making a contact print A contact print is the positive print of all the negatives of a film on a single piece of 20 x 24cm (8x10 ) paper Requirements Contact printer Blower brush Filter printing kit Photographic paper A4 card Negatives

Printing the negatives View negatives on light box but keep in sleeves to avoid static which encourages dust Select a strip of negatives and decide whether normal

14 Printing the negatives View negatives on light box but keep in sleeves to avoid static which encourages dust Select a strip of negatives and decide whether normal exposure (density), under or over exposed in general Filter selection depends on densities/exposures (see table below) Ensure the glass of the contact printer is clean

16 The entire process

ILFORDINFO HOW TO PROCESS YOUR FIRST BLACK AND WHITE FILM

ILFORDINFO HOW TO PROCESS YOUR FIRST BLACK AND WHITE FILM Your darkroom (kitchen, bathroom or cupboard) needs to be completely blacked out to stop light from entering. For windows use thick card cut to