Computerized Embroidery and Sewing Machine. Operation Manual

Size: px
Start display at page:

Download "Computerized Embroidery and Sewing Machine. Operation Manual"

Transcription

1 GETTING READY SEWING BASICS 2 UTILITY STITCHES 3 EMBROIDERY 4 APPENDIX 5 Computerized Emroidery nd Sewing Mhine Opertion Mnul Produt Code: 885-U0/U04 Be sure to red this doument efore using the mhine. We reommend tht you keep this doument nery for future referene.

2

3 IMPORTANT SAFETY INSTRUCTIONS Plese red these sfety instrutions efore ttempting to use the mhine. DANGER - To redue the risk of eletri shok: Alwys unplug the mhine from the eletril outlet immeditely fter using, when lening, when mking ny user serviing djustments mentioned in this mnul, or if you re leving the mhine unttended. WARNING - To redue the risk of urns, fire, eletri shok, or injury to persons. 2 Alwys unplug the mhine from the eletril outlet when mking ny djustments mentioned in the instrution mnul: To unplug the mhine, swith the mhine to the symol O position to turn it off, then grsp the plug nd pull it out of the eletril outlet. Do not pull on the ord. Plug the mhine diretly into the eletril outlet. Do not use n extension ord. Alwys unplug your mhine if the power is ut. 3 Eletril Hzrds: This mhine should e onneted to n AC power soure within the rnge indited on the rting lel. Do not onnet it to DC power soure or inverter. If you re not sure wht kind of power soure you hve, ontt qulified eletriin. This mhine is pproved for use in the ountry of purhse only. 4 Never operte this mhine if it hs dmged ord or plug, if it is not working properly, if it hs een dropped or dmged, or wter is spilled on the unit. Return the mhine to the nerest uthorized deler or servie enter for exmintion, repir, eletril or mehnil djustment. While the mhine is stored or in use if you notie nything unusul, suh s n odor, het, disolortion or deformtion, stop using the mhine nd immeditely unplug the power ord. When trnsporting the sewing mhine, e sure to rry it y its hndle. Lifting the sewing mhine y ny other prt my dmge the mhine or result in the mhine flling, whih ould use injuries. When lifting the sewing mhine, e reful not to mke ny sudden or reless movements, otherwise you my injure your k or knees. 5 Alwys keep your work re ler: Never operte the mhine with ny ir openings loked. Keep ventiltion openings of the sewing mhine nd foot ontrol free from the uild up of lint, dust, nd loose loth. Do not store ojets on the foot ontroller. Do not use extension ords. Plug the mhine diretly into the eletril outlet. Never drop or insert ny ojet into ny opening. Do not operte where erosol (spry) produts re eing used or where oxygen is eing dministered. Do not use the mhine ner het soure, suh s stove or iron; otherwise, the mhine, power ord or grment eing sewn my ignite, resulting in fire or n eletri shok. Do not ple this sewing mhine on n unstle surfe, suh s n unstedy or slnted tle, otherwise the sewing mhine my fll, resulting in injuries.

4 6 Speil re is required when sewing: Alwys py lose ttention to the needle. Do not use ent or dmged needles. Keep fingers wy from ll moving prts. Speil re is required round the mhine needle. Swith the sewing mhine to the symol O position to turn it off when mking ny djustments in the needle re. Do not use dmged or inorret needle plte, s it ould use the needle to rek. Do not push or pull the fri when sewing, nd follow reful instrution when freehnd stithing so tht you do not deflet the needle nd use it to rek. 7 This mhine is not toy: Your lose ttention is neessry when the mhine is used y or ner hildren. The plsti g tht this sewing mhine ws supplied in should e kept out of the reh of hildren or disposed of. Never llow hildren to ply with the g due to the dnger of suffotion. Do not use outdoors. 8 For longer servie life: When storing this mhine, void diret sunlight nd high humidity lotions. Do not use or store the mhine ner spe heter, iron, hlogen lmp, or other hot ojets. Use only neutrl sops or detergents to len the se. Benzene, thinner, nd souring powders n dmge the se nd mhine, nd should never e used. Alwys onsult the opertion mnul when repling or instlling ny ssemlies, the presser feet, needle, or other prts to ssure orret instlltion. 9 For repir or djustment: If the Light unit (light-emitting diode) is dmged, it must e repled y uthorized deler. In the event mlfuntion ours or djustment is required, first follow the trouleshooting tle in the k of the opertion mnul to inspet nd djust the mhine yourself. If the prolem persists, plese onsult your lol uthorized Brother deler. Use this mhine only for its intended use s desried in this mnul. Use essories reommended y the mnufturer s ontined in this mnul. The ontents of this mnul nd speifitions of this produt re sujet to hnge without notie. For dditionl produt informtion, visit our we site t 2

5 SAVE THESE INSTRUCTIONS This mhine is intended for household use. FOR USERS IN COUNTRIES EXCEPT EUROPEAN COUNTRIES This ppline is not intended for use y persons (inluding hildren) with redued physil, sensory or mentl pilities, or lk of experiene nd knowledge, unless they hve een given supervision or instrution onerning use of the ppline y person responsile for their sfety. Children should e supervised to ensure tht they do not ply with the ppline. FOR USERS IN EUROPEAN COUNTRIES This ppline n e used y hildren ged from 8 yers nd ove nd persons with redued physil, sensory or mentl pilities or lk of experiene nd knowledge if they hve een given supervision or instrution onerning use of the ppline in sfe wy nd understnd the hzrds involved. Children shll not ply with the ppline. Clening nd user mintenne shll not e mde y hildren without supervision. IMPORTANT FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY In the event of repling the plug fuse, use fuse pproved y ASTA to BS 362, i.e. rrying the mrk, rting s mrked on plug. Alwys reple the fuse over. Never use plugs with the fuse over omitted. If the ville eletril outlet is not suitle for the plug supplied with this equipment, you should ontt your uthorized deler to otin the orret led. 3

6 4

7 Contents IMPORTANT SAFETY INSTRUCTIONS... Introdution...9 Sewing Mhine Fetures...9 Aessories...0 Inluded essories...0 Optionl essories...2 Nmes of Mhine Prts nd Their Funtions...3 Front view...3 Needle nd presser foot setion...4 Right-side/rer view...4 Opertion uttons...5 Opertion pnel...6 GETTING READY 7 Turning the Mhine On/Off...8 Power supply preutions...8 Turning on the mhine...9 Turning off the mhine...9 LCD (Liquid Crystl Disply) Opertion...20 Viewing the LCD...20 Chnging the mhine settings...2 Cheking mhine operting proedures...23 Winding/Instlling the Boin...25 Boin preutions...25 Winding the oin...25 Instlling the oin...29 Upper Threding...3 Aout the spool of thred...3 Threding the upper thred...32 Threding the needle...34 Threding the needle mnully (without using the needle threder)...35 Using the twin needle...36 Pulling up the oin thred...39 Repling the Needle...40 Needle preutions...40 Needle types nd their uses...4 Cheking the needle...42 Repling the needle...42 Repling the Presser Foot...44 Presser foot preutions...44 Repling the presser foot...44 Removing nd tthing the presser foot holder...46 Sewing Cylindril Piees...47 Free-rm sewing...47 SEWING BASICS 49 Sewing...50 Generl sewing proedure...50 Seleting stithing...5 Positioning the fri...52 Strting to sew...53 Seuring the stithing...55 Cutting the thred...56 Setting the Stith...58 Adjusting the stith width...58 Adjusting the stith length...59 Adjusting the thred tension

8 Useful Funtions...6 Automtilly sewing reverse/reinforement stithes...6 Automtilly utting the thred...62 Mirroring stithes...63 Useful Sewing Tips...64 Tril sewing...64 Chnging the sewing diretion...64 Sewing urves...64 Adjusting the presser foot pressure...64 Sewing thik fris...65 Sewing thin fris...66 Sewing streth fris...66 Sewing lethers or vinyl fris...66 Sewing n even sem llowne...66 Hnds-free rising nd lowering of the presser foot...67 Sewing hook-nd-loop fstener...68 UTILITY STITCHES 69 Stith Setting Chrt...70 Utility stithes...70 Other stithes...74 Seleting Stithing...77 Stith types...77 Seleting stithing...77 Sving stith settings...79 Oversting Stithes...8 Sewing oversting stithes using oversting foot G...8 Sewing oversting stithes using zigzg foot J...82 Sewing oversting stithes using the optionl side utter...83 Bsi Stithing...85 Bsting...85 Bsi stithing...85 Blind Hem Stithing...87 Buttonhole Stithing/Button Sewing...89 Buttonhole sewing...90 Button sewing...94 Zipper Insertion...96 Inserting entered zipper...96 Inserting side zipper...98 Zipper/piping Insertion...0 Inserting entered zipper...0 Inserting piping...02 Sewing Streth Fris nd Elsti Tpe...03 Streth stithing...03 Elsti tthing...03 Appliqué, Pthwork nd Quilt Stithing...05 Appliqué stithing...06 Pthwork (rzy quilt) stithing...07 Pieing...07 Quilting...09 Free-motion quilting...0 Stin stithing using the sewing speed ontroller... Reinforement Stithing...3 Triple streth stithing...3 Br tk stithing...3 Drning...5 Eyelet Stithing...7 Horizontl Stithing...8 6

9 Deortive Stithing...20 Fgoting...2 Sllop stithing...22 Smoking...22 Shell tuk stithing...23 Joining...24 Heirloom stithing...25 Sewing the Vrious Built-in Deortive Ptterns...28 Sewing eutiful ptterns...28 Sewing ptterns...28 Chnging the pttern size...29 Chnging the stith density...29 Chnging the length for stin stithes...30 Shifting ptterns...3 Comining ptterns...32 Sving ptterns...35 Religning the pttern...36 Designing Pttern (My Custom Stith)...39 Drwing sketh of the pttern...39 Entering the pttern dt...40 Exmples of designs...42 EMBROIDERY 43 Suessful Emroidering...44 Wht to prepre...44 Emroidery step y step...46 Atthing the Emroidery Foot...47 Atthing the emroidery foot...47 Removing the emroidery foot...49 Atthing the Emroidery Unit...50 Emroidery unit preutions...50 Atthing the emroidery unit...50 Removing the emroidery unit...52 Prepring the Fri...53 Atthing n optionl stilizer mteril to the fri...53 Setting the fri in the emroidery frme...54 Atthing the Emroidery Frme...57 Atthing the emroidery frme...57 Removing the emroidery frme...58 Seleting Emroidery Ptterns...59 Copyright informtion...59 Emroidery pttern types...59 LCD (liquid rystl disply) opertion...60 Seleting n emroidery pttern...62 Seleting hrters...63 Seleting frme pttern...64 Using n emroidery rd (sold seprtely)...65 Emroidering...66 Sewing ttrtive finishes...66 Emroidering pttern...67 Appliquéing...69 Editing Ptterns...7 Adjusting the lyout...7 Adjusting the thred tension...73 Adjusting the lternte oin se (with no olor on the srew)...74 Resewing...75 Thred runs out prtwy through design...75 Stopping while emroidering...76 Using the Memory Funtion...78 Emroidery dt preutions...78 Sving ptterns...80 Trnsferring emroidery ptterns from the omputer to mhine...8 7

10 APPENDIX 83 Cre nd Mintenne...84 Restritions on oiling...84 Preutions on storing the mhine...84 Clening the mhine surfe...84 Clening the re...84 Trouleshooting...86 Frequent trouleshooting topis...86 Upper thred tightened up...86 Tngled thred on wrong side of fri...87 Inorret thred tension...89 Fri is ught in the mhine nd nnot e removed...90 When the thred eme tngled under the oin winder set...93 List of symptoms...95 Error messges...20 Adjusting the LCD Opertion eep Cneling the opertion eep Upgrding Your Mhine s Softwre Using USB Medi Index

11 Introdution Thnk you for purhsing this sewing mhine. Before using this sewing mhine, refully red the IMPORTANT SAFETY INSTRUCTIONS (pge ), nd then study this mnul for the orret opertion of the vrious funtions. In ddition, fter you hve finished reding this mnul, store it where it n quikly e essed for future referene. Sewing Mhine Fetures d e f Simple oin-winding The oin n quikly nd esily e wound with thred (pge 25). Built-in stithes You n selet from the uilt-in stithes ville, inluding utility stithes nd deortive stithes (pge 70). Quik-set oin You n strt sewing without pulling up the oin thred (pge 29). Automti thred utting The thred n e ut utomtilly fter sewing (pge 62). Emroidery You n emroider uilt-in emroidery ptterns, hrters, frmed deortions, nd designs from optionl emroidery rds (pge 43). Knee lifter Use the knee lifter to rise nd lower the presser foot with your knee, leving oth hnds free to hndle the fri (pge 67). Introdution / Sewing Mhine Fetures 9

12 Aessories Inluded essories After opening the ox, hek tht the following essories re inluded. If ny item is missing or dmged, ontt your deler. Note (For U.S.A. only) Foot ontroller: Model T This foot ontroller n e used on the mhine with produt ode:885-u0/u04. The produt ode is mentioned on the mhine rting plte. The srew for the presser foot holder is ville through your uthorized deler. (Prt ode: ) The orgnized essory try is ville through your uthorized deler. (Prt ode: XC ) * *75/ 2 needles 90/4 2 needles 90/4 2 needles: Bll point needle (gold olored) 0

13 No. Prt Nme Prt Code Ameris Others Buttonhole foot A XC Oversting foot G XC Monogrmming foot N XD Zipper foot I X Zigzg foot J (on mhine) XZ Blind stith foot R XE Button fitting foot M XE Stith guide foot P SA60 F035N: XC Adjustle zipper/piping F036N: SA6 foot XC Non stik foot SA4 F007N: XC Open toe foot SA86 F060: XE Sem ripper XZ Boin (4) SA56 SFB: XA Needle set X Twin needle X Clening rush X Eyelet punh XZ Srewdriver (lrge) XC Srewdriver (smll) X Spool p (lrge) Spool p (medium) (2) XE Spool p (smll) No. Prt Nme Prt Code Ameris Others 23 Extr spool pin XC Spool net XA Foot ontroller XZ (EU re) XZ500-00(other res) 26 Opertion mnul XE Quik referene guide XD Emroidery foot Q XD Emroidery set (lrge) 29 H 8 m W 3 m EF84: (H 7 inhes W 5 SA444 XF inhes) 30 Emroidery set (extr lrge (multi-position)) H 30 m W 3 m (H 2 inhes W 5 inhes) SA445 EF85: XG Emroidery oin thred (white) 32 Alternte oin se (no olor on the srew) 33 Knee lifter XA Grid sheet set XC Sissors XC Hrd se XC Aessory g XC Dis-shped srewdriver XC EBT-CEN: SA-EBT X XC Aessories

14 Optionl essories The following re ville s optionl essories to e purhsed seprtely Prt Code No. Prt Nme Ameris Others Emroidery oin EBT-CEN: SA-EBT thred (white) X Emroidery oin EBT-CEBN: SAEBT999 thred (lk) XC Emroidery rd Emroidery set (smll) EF82: 3 H 2 m W 6 m SA442 (H inh W 2-/2 inhes) XG Emroidery set (medium) H 0 m W 0 m (H 4 inhes W 4 inhes) Wter solude stilizer Stilizer mteril for emroidery SA443 SA520 SA59 6 Wide tle SA55 7 Wlking foot SA40 8 Quilting foot SA29 9 /4 inh quilting foot SA25 0 Side utter S SA77 Quilting guide SA32 2 /4 inh quilting foot with guide SA85 3 Cirulr tthment SACIRC EF83: XG BM5: XE BM3: XE WT5: XC F033N: XC F005N: XC F00N: XC F054: XC F06N: XC F057: XC CIRC: XE Memo To otin optionl essories or prts, ontt your sles representtive or the nerest uthorized servie enter. All speifitions re orret t the time of printing. The prt odes re sujet to hnge without notie. Visit your nerest uthorized retiler for omplete listing of optionl essories ville for your mhine. 2

15 Nmes of Mhine Prts nd Their Funtions The nmes of the vrious prts of the sewing mhine nd their funtions re desried elow. Before using the sewing mhine, refully red these desriptions to lern the nmes of the mhine prts. Front view d e f g h Thred guide plte Pss the thred under the thred guide plte. Thred guide over Pss the thred ehind the thred guide over when threding the upper thred. Spool pin Ple spool of thred on the spool pin. Boin winding thred guide nd pretension disk Pss the thred under this thred guide nd round the pretension disk when winding the oin thred. Top over Open the top over to ple the spool of thred on the spool pin. Boin winder Use the oin winder when winding the oin. Opertion pnel From the opertion pnel, stith settings n e viewed nd edited, nd opertions for using the mhine n e displyed (pge 6). Knee lifter mounting slot Insert the knee lifter into the knee lifter mounting slot. i j k l m n o Emroidery unit onnetor slot Plug in the onnetor for the emroidery unit. Presser foot lever Rise nd lower the presser foot lever to rise nd lower the presser foot. Opertion uttons nd sewing speed ontroller Use these uttons nd the slide to operte the sewing mhine (pge 5). Flt ed tthment Insert the essories try into the essory omprtment of the flt ed tthment. Remove the flt ed tthment when sewing ylindril piees suh s sleeve uffs. Thred utter Pss the threds through the thred utter to ut them. Needle threder lever Use the needle threder lever to thred the needle. Thred tke-up lever hek window Look through the window to hek the position of the tke-up lever. Nmes of Mhine Prts nd Their Funtions 3

16 Needle nd presser foot setion Right-side/rer view d e f g h i Buttonhole lever The uttonhole lever is used with the one-step uttonhole foot to rete uttonholes. Thred guide disk Pss the thred through the thred guide disk when using the needle threder to thred the needle. Needle r thred guide Pss the upper thred through the needle r thred guide. Needle plte The needle plte is mrked with guides to help sew stright sems. Needle plte over Remove the needle plte over to len the oin se nd re. Boin over Open the oin over to set the oin. Feed dogs The feed dogs feed the fri in the sewing diretion. Presser foot The presser foot pplies pressure onsistently on the fri s sewing tkes ple. Atth the pproprite presser foot for the seleted stith. Presser foot holder The presser foot is tthed onto the presser foot holder. d e f g h i j k Hndle Crry the sewing mhine y its hndle when trnsporting the mhine. Hndwheel Turn the hndwheel towrd you to rise nd lower the needle. The hndwheel should e turned towrds you (ounterlokwise). Emroidery rd slot Insert the emroidery rd. USB port (for USB flsh drive (USB flsh memory)) In order to import ptterns from USB flsh drive (USB flsh memory), plug the USB medi diretly into the USB port. Air vent The ir vent llows the ir surrounding the motor to irulte. Do not over the ir vent while the sewing mhine is eing used. Min power swith Use the min power swith to turn the sewing mhine ON nd OFF. Foot ontroller jk Insert the plug on the end of the foot ontroller le into the foot ontroller jk. Power supply jk Insert the plug on the power ord into the power supply jk. Feed dog position swith Use the feed dog position swith to lower the feed dogs. Presser foot pressure dil Use the presser foot pressure dil to djust the mount of pressure tht the presser foot pplies. Presser foot lever Rise nd lower the presser foot lever to rise nd lower the presser foot. Memo Refer to pges 3 through 6 while you re lerning to use your mhine. 4

17 Opertion uttons The opertion uttons help you to esily perform vrious si sewing mhine opertions. d e Strt/Stop utton Press the Strt/Stop utton to strt or stop sewing. The mhine sews t slow speed t the eginning of sewing while the utton is pressed. When sewing is stopped, the needle is lowered in the fri. For detils, refer to Strting to sew (pge 53). The utton hnges olor ording to the mhine s opertion mode. Green: Red: Ornge: The mhine is redy to sew or is sewing. The mhine n not sew. The mhine is winding the oin thred, or the oin winder shft is moved to the right side. Reverse/Reinforement Stith utton Press the Reverse/Reinforement Stith utton to sew reverse stithes or reinforement stithes. Reverse stithes re sewn y keeping the utton pressed down to sew in the opposite diretion. Reinforement stithes re sewn y sewing 3 to 5 stithes on top of eh other. For detils, refer to Seuring the stithing (pge 55). Needle Position utton Press the Needle Position utton to rise or lower the needle. Pressing the utton twie sews one stith. Thred Cutter utton Press the Thred Cutter utton fter sewing is stopped to ut oth the upper nd the oin threds. For detils, refer to Cutting the thred (pge 56). Sewing speed ontroller Slide the sewing speed ontroller to djust the sewing speed. Note Do not press ( Thred Cutter utton) if there is no fri under the presser foot or while the mhine is sewing, otherwise dmge to the mhine my our. When utting thred thiker thn #30, nylon thred or other speil threds, use the thred utter on the side of the mhine. For detils, refer to Using the thred utter (pge 57). CAUTION Do not press ( Thred Cutter utton) fter the threds hve lredy een ut, otherwise the needle my rek, the threds my eome tngled or dmge to the mhine my our. Nmes of Mhine Prts nd Their Funtions 5

18 Opertion pnel The front opertion pnel hs n LCD (liquid rystl disply) nd opertion keys. f d e i d e LCD (liquid rystl disply) (touh pnel) Seleted pttern settings nd messges re displyed. Touh the keys displyed on the LCD to perform opertions. For detils, refer to LCD (Liquid Crystl Disply) Opertion (pge 20). Bk key Press to return to the previous sreen. Previous pge key Displys the previous sreen when there re items tht re not displyed on the LCD. Next pge key Displys the next sreen when there re items tht re not displyed on the LCD. Memory key Press to enter hrter emroidery, omined stith ptterns, My Custom Stith ptterns, et into the sewing mhine memory. g f g h i h Utility stith key Press this key to selet utility stith or deortive stith or to design stith pttern using the My Custom Stith funtion. Emroidery key Press this key to sew emroidery. Settings key Press to set the needle stop position, the uzzer sound, nd more. Sewing mhine help key Press to get help on using the sewing mhine. Displys simple explntions of setting upper thred / oin winding / setting oin thred / needle replement / emroidery unit tthment / emroidery frme tthment / emroidery foot tthment / presser foot replement. 6

19 GETTING READY The vrious preprtions required efore strting to sew re desried in this hpter. Turning the Mhine On/Off...8 Power supply preutions...8 Turning on the mhine...9 Turning off the mhine...9 LCD (Liquid Crystl Disply) Opertion...20 Viewing the LCD...20 Chnging the mhine settings...2 Cheking mhine operting proedures...23 Winding/Instlling the Boin...25 Boin preutions...25 Winding the oin...25 Instlling the oin...29 Upper Threding...3 Aout the spool of thred...3 Threding the upper thred...32 Threding the needle...34 Threding the needle mnully (without using the needle threder)...35 Using the twin needle...36 Pulling up the oin thred...39 Repling the Needle...40 Needle preutions...40 Needle types nd their uses...4 Cheking the needle...42 Repling the needle...42 Repling the Presser Foot...44 Presser foot preutions...44 Repling the presser foot...44 Removing nd tthing the presser foot holder...46 Sewing Cylindril Piees...47 Free-rm sewing...47

20 GETTING READY Turning the Mhine On/Off This setion explins how to turn the sewing mhine on nd off. Power supply preutions Be sure to oserve the following preutions onerning the power supply. WARNING Use only regulr household eletriity for the power soure. Using other power soures my result in fire, eletri shok, or dmge to the mhine. Mke sure tht the plugs on the power ord re firmly inserted into the eletril outlet nd the power supply jk on the mhine. Do not insert the plug on the power ord into n eletril outlet tht is in poor ondition. Turn off the min power nd remove the plug in the following irumstnes: When you re wy from the mhine After using the mhine When the power fils during use When the mhine does not operte orretly due to d onnetion or disonnetion During eletril storms CAUTION Use only the power ord inluded with this mhine. Do not use extension ords or multi-plug dpters with mny other pplines plugged in to them. Fire or eletri shok my result. Do not touh the plug with wet hnds. Eletri shok my result. When unplugging the mhine, lwys turn off the min power first. Alwys grsp the plug to remove it from the outlet. Pulling on the ord my dmge the ord, or led to fire or eletri shok. Do not llow the power ord to e ut, dmged, modified, forefully ent, pulled, twisted, or undled. Do not ple hevy ojets on the ord. Do not sujet the ord to het. These things my dmge the ord nd use fire or eletri shok. If the ord or plug is dmged, tke the mhine to your uthorized deler for repirs efore ontinuing use. Unplug the power ord if the mhine is not to e used for long period of time. Otherwise fire my result. 8

21 Turning on the mhine Prepre the inluded power ord. Mke sure tht the sewing mhine is turned off (the min power swith is set to ), nd then plug the power ord into the power supply jk on the right side of the mhine. Insert the plug of the power ord into household eletril outlet. Turning off the mhine When you re finished using the sewing mhine, turn it off. In ddition, efore trnsporting the sewing mhine to nother lotion, e sure to turn it off. Mke sure tht the mhine is not sewing. Press the left side of the min power swith on the right side of the mhine to turn the mhine off (set it to ). The sewing lmps nd the LCD go off when the mhine is turned off. Power supply jk Unplug the power ord from the eletril outlet. Grsp the plug when unplugging the power ord. Press the right side of the min power swith on the right side of the mhine to turn the mhine on (set it to I ). The light, LCD nd ( Strt/Stop utton) light up when the mhine is turned on. Memo When the mhine is turned on, the needle nd the feed dogs will mke sound when they move; this is not mlfuntion. d Unplug the power ord from the power supply jk. Note If power outge ours while the sewing mhine is eing operted, turn off the sewing mhine nd unplug the power ord. When restrting the sewing mhine, follow the neessry proedure to orretly operte the mhine. (For U.S.A. only) This ppline hs polrized plug (one lde wider thn the other). To redue the risk of eletril shok, this plug is intended to fit in polrized outlet only one wy. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, ontt qulified eletriin to instll the proper outlet. Do not modify the plug in ny wy. Turning the Mhine On/Off 9

22 GETTING READY LCD (Liquid Crystl Disply) Opertion Seleted stith, pttern settings nd messges re displyed on the LCD (liquid rystl disply) on the front of the sewing mhine. Viewing the LCD When the power is turned on, the LCD omes on, nd the following sreen is displyed. The sreen is hnged using the keys elow the sreen, nd opertions performed y diretly touhing the ions on the LCD sreen. Utility stith seletion sreen m l k d e j h i g f Seleted stith i Numer of stithes ontined in the seleted stith Presser foot to e used type Stithes j Horizontl mirror imge d Stith settings nd twin needle sewing k Automti thred utting e Stith width (mm) l Automti reverse/reinforement f Stith length (mm) m Single/twin needle sewing nd needle stop position g Thred tension h Numer of the seleted stith Stith type seletion sreen Press (Utility stith key) to disply the sreen for seleting the stith type. The detils re explined in Seleting stithing (pge 5). Memo A different sreen is displyed when the emroidery unit is tthed. Refer to Error messges (pge 20) for messges displyed on the LCD. Depending on the model of sewing mhine, n nimtion my e displyed when the power is turned on. When n nimtion is displyed, the sreen ove will e displyed if you touh the LCD with your finger. 20

23 Chnging the mhine settings Vrious sewing mhine opertions nd sewing settings n e hnged. The stith or mhine ttriutes tht n e set re listed elow. Attriute Ion Detils Settings Needle position Stith width ontrol Speifies where the needle is positioned when the sewing mhine is stopped. Allows the stith width to e djusted with the sewing speed ontroller. Down Up Vertil pttern djustment Horizontl pttern djustment Thred olor disply Disply unit Emroidery tension Mx emroidery speed Buzzer Opening sreen Initil needle position Lnguge Adjusts the up nd down position of the pttern (pge 36). Adjusts the left nd right position of the pttern (pge 36). Chnges the thred olor disply on the emroidery sreen. (When Thred No. #23 is seleted) Selets the mesurement units tht re displyed (only for emroidering). Adjusts the thred tension for emroidering (only for emroidering). Speifies the mximum emroidering speed. Speifies whether or not eep is sounded with eh opertion (pge 205). Sets whether or not to disply the opening sreen when the power is turned on. (There re models where this nnot e hnged.) Selet the stright stith tht is utomtilly seleted when the mhine is turned on. Allows the lnguge used in the sreens to e hnged. -9 to +9-9 to +9 Thred olor/time to emroider/ Needle ount/thred numer (#23) Emroidery/Country/Mdeir poly/ Mdeir ryon/sulky/roison nton mm/inch -8 to +8 English/Frenh/Spnish/Portuguese/ Koren/others Memo Depending on the model, the following lnguges my lso e ville. Germn/Itlin/Duth/Jpnese/ Dnish/Norwegin/Finnish/ Swedish/Russin/Thi LCD rightness Adjusts the rightness of the LCD. Lighter Drker Stith ounter Produt numer NO.: Disply the servie ount nd the totl numer of emroidery stithes. The servie ount is reminder to tke your mhine in for regulr serviing. (Contt your uthorized deler for detils.) The NO. is the numer for the sewing nd emroidery mhine. Progrm version VERSION: Disply the progrm version. LCD (Liquid Crystl Disply) Opertion 2

24 GETTING READY Turn on the sewing mhine. The LCD omes on. Press pnel. (Settings key) on the opertion The settings sreen ppers. Press the item to e set. Swith sreens using (Previous pge key) nd (Next pge key). The items shown in reverse highlighting re the settings t the time of purhse. Exmple: Chnging the needle stop position 22

25 d When settings re omplete, press (Bk key). Cheking mhine operting proedures Displys simple explntions of setting upper thred / oin winding / setting oin thred / needle replement / emroidery unit tthment / emroidery frme tthment / emroidery foot tthment / presser foot replement on the LCD. The initil sreen ppers gin. Turn on the sewing mhine. Note Settings tht re hnged re not lost when the power is turned off. The LCD omes on. Press (Sewing mhine help key) on the opertion pnel. The sewing mhine help sreen ppers. Press the item to e displyed. d e f h g Upper threding Boin winding Boin instlltion d Needle replement e Emroidery unit tthment f Emroidery frme tthment g Emroidery foot tthment h Presser foot replement The first sreen desriing the proedure for the seleted topi ppers. Pressing (Bk key), returns you to the item seletion sreen. LCD (Liquid Crystl Disply) Opertion 23

26 GETTING READY Press (Next pge key) to swith to the d next pge. If you press (Previous pge key), you return to the previous pge. Exmple: Upper threding The initil stith sreen ppers gin. Note For detils on eh topi, refer to the orresponding pge in this Opertion Mnul. After you finish looking, press e key) two times. (Bk 24

27 Winding/Instlling the Boin This setion desries how to wind the thred onto the oin, nd then insert the oin thred. Boin preutions Be sure to oserve the following preutions onerning the oin. CAUTION Only use the Boin (prt ode: SA56, SFB: XA5539-5) designed speifilly for this sewing mhine. Use of ny other oin my result in injuries or dmge to the mhine. The inluded oin ws designed speifilly for this sewing mhine. If oins from other models re used, the mhine will not operte orretly. Use only the inluded oin or oins of the sme type (prt ode: SA56, SFB: XA5539-5)..5 mm (7/6 inh) Atul size This model Other model Winding the oin Wind the thred round the oin to prepre the oin thred. Boin winder Memo The order tht the mhine should e threded for winding the oin is indited y roken line on the sewing mhine. Be sure to thred the mhine s indited. Winding/Instlling the Boin 25

28 GETTING READY Turn on the sewing mhine. f Ple the spool of thred for the oin onto the spool pin. Slide the spool onto the pin so tht the spool is horizontl nd the thred unwinds to the front t the ottom. Open the top over. Ple the oin on the oin winder shft so tht the spring on the shft fits into the noth in the oin. Press down on the oin until it snps into ple. If the spool is not positioned so tht the thred unwinds orretly, the thred my eome tngled round the spool pin. Slide the spool p onto the spool pin. g Slide the spool p s fr s possile to the right, s shown, with the rounded side on the left. d Noth Boin winder shft spring Slide the oin winder in the diretion of the rrow until it snps into ple. CAUTION If the spool or the spool p is not positioned orretly, the thred my eome tngled round the spool pin nd the needle my rek. Three spool p sizes re ville (lrge, medium nd smll), llowing you to hoose spool p tht est fits the size of spool eing used. If the spool p is too smll for the spool eing used, the thred my th on the slit in the spool or the mhine my e dmged. ( Strt/Stop utton) lights up in ornge. e Remove the spool p tht is inserted onto the spool pin. Spool pin Spool p 26

29 Memo When sewing with fine, ross-wound thred, use the smll spool p, nd leve smll spe etween the p nd the spool. While holding the thred ner the spool with h your right hnd, s shown, pull the thred with your left hnd, nd then pss the thred ehind the thred guide over nd to the front. Spool p (smll) Spool (ross-wound thred) Spe When using thred tht winds off quikly, suh s trnsprent nylon thred or metlli thred, ple the spool net over the spool efore pling the spool of thred onto the spool pin. If the spool net is too long, fold it to fit the size of the spool. When the spool net is used, the tension of the upper thred will slightly inrese. Be sure to hek the thred tension. For detils, refer to Adjusting the thred tension (pge 59). i j Thred guide over Pss the thred under the thred guide plte, nd then pull it to the right. Thred guide plte Pss the thred under the hook on the thred guide, nd then wind it ounterlokwise under the pretension disk. 2 d Spool net Spool Spool p Spool pin 3 Thred guide Pretension disk Pull it in s fr s possile Note Mke sure tht the thred psses under the pretension disk. Winding/Instlling the Boin 27

30 GETTING READY k While holding the thred with your left hnd, wind the thred tht ws pulled out lokwise round the oin five or six times with your right hnd. Press ( Strt/Stop utton) one to strt n winding the oin. When the foot ontroller is plugged in, press down on the foot ontroller. l Note Mke sure tht the thred etween the spool nd the oin is pulled tight. Be sure to wind the thred lokwise round the oin, otherwise the thred will eome wrpped round the oin winder shft. Pss the end of the thred through the guide slit in the oin winder set, nd then pull the thred to the right to ut it. Guide slit in oin winder set (with uilt-in utter) The thred is ut to suitle length. Strt/Stop utton When the oin winding eomes slow, press ( Strt/Stop utton) one to stop the mhine. When the foot ontroller is plugged in, remove your foot from the foot ontroller. CAUTION When the oin winding eomes slow, stop the mhine, otherwise the sewing mhine my e dmged. o Use sissors to ut the end of the thred wound round the oin. CAUTION Be sure to ut the thred s desried. If the oin is wound without utting the thred using the utter uilt into the slit in the oin winder set, the thred my eome tngled in the oin nd the needle my end or rek when the oin thred strts to run out. p Slide the oin winder shft to the left, nd then remove the oin from the shft. m Slide the sewing speed ontroller to the right to inrese the oin winding speed nd slide to left to derese. Memo If the oin winder shft is set to the right side, the needle will not move. (Sewing is impossile.) Speed ontroller 28

31 q Remove the spool for the oin thred from the spool pin, nd then lose the top over. Memo When the sewing mhine is strted or the hndwheel is turned fter winding the oin, the mhine will mke liking sound; this is not mlfuntion. Press ( Needle Position utton) one or twie to rise the needle, nd then rise the presser foot lever. Turn off the sewing mhine. Slide the oin over lth to the right. Instlling the oin Instll the oin wound with thred. CAUTION Use oin tht hs een orretly wound with thred, otherwise the needle my rek or the thred tension will e inorret. Boin over Lth The oin over opens. Remove the oin over. d Hold the oin with your right hnd nd hold e the end of the thred with your left. The oin ws designed speifilly for this sewing mhine. If oins from other models re used, the mhine will not operte orretly. Use only the inluded oin or oins of the sme type (prt ode: SA56, SFB (XA5539-5))..5 mm (7/6 inh) Atul size f Be reful not to drop the oin. Insert the oin with your right hnd so tht the end of the thred is on the left, nd then, fter pulling the thred firmly round the t with your left hnd s shown, lightly pull the thred to guide it through the slit. This model Other model T Winding/Instlling the Boin 29

32 GETTING READY CAUTION Be sure to instll the oin so tht the thred unwinds in the orret diretion, otherwise the thred my rek or the thred tension will e inorret. Note Mke sure tht the thred is orretly inserted through the tension-djusting spring of the oin se. If it is not inserted orretly, reinsert the thred. Memo The order tht the oin thred should e pssed through the oin se is indited y mrks round the oin se. Be sure to thred the mhine s indited. Tension-djusting spring g While lightly holding down oin with your right hnd s shown, guide the thred through the slit ( nd 2). At this time, hek tht the oin esily rottes ounterlokwise. Then, pull the thred towrd you to ut it with the utter (3). Retth the oin over. h Insert the t in the lower-left orner of the oin over, nd then lightly press down on the right side. The oin threding is finished. Next, thred the upper thred. Continue with the proedure in Upper Threding (pge 3). Slit Cutter (Cut the thred with the utter.) Memo You n egin sewing without pulling up the oin thred. If you wish to pull up the oin thred efore strting to sew, pull up the thred ording to the proedure in Pulling up the oin thred (pge 39). 30

33 Upper Threding This setion desries how to position the spool for the upper thred, nd then thred the needle. CAUTION When threding the upper thred, refully follow the instrutions. If the upper threding is not orret, the thred my eome tngled nd the needle my end or rek. Memo The order tht the mhine should e threded is indited y solid line on the sewing mhine. Be sure to thred the mhine s indited. Aout the spool of thred Informtion out the spools of thred is desried elow. CAUTION Three spool p sizes re ville (lrge, medium nd smll), llowing you to hoose spool p tht est fits the size of spool eing used. If the spool p is too smll for the spool eing used, the thred my th on the slit in the spool nd the needle my rek. Upper Threding 3

34 GETTING READY Threding the upper thred Open the top over. d Set the spool of thred on the spool pin, nd then thred the mhine. Turn on the sewing mhine. e Remove the spool p tht is inserted onto the spool pin. Rise the presser foot lever to rise the presser foot. Spool pin Spool p Presser foot lever Note If the presser foot is not rised, the sewing mhine nnot e threded. f Ple the spool of thred onto the spool pin. Slide the spool onto the pin so tht the spool is horizontl nd the thred unwinds to the front t the ottom. Press ( Needle Position utton) one or twie to rise the needle. Needle Position utton The needle is orretly rised when the mrk on the hndwheel is t the top, s shown elow. Chek the hndwheel nd, if this mrk is not t this position, press ( Needle Position utton) until it is. CAUTION If the spool or the spool p is not positioned orretly, the thred my eome tngled round the spool pin nd the needle my rek. Slide the spool p onto the spool pin. g Slide the spool p s fr s possile to the right, s shown, with the rounded side on the left. Mrk on hndwheel 32

35 While holding the thred lightly with your h right hnd, pull the thred with your left hnd, nd then pss the thred ehind the thred guide over nd to the front. Note If the presser foot hs een lowered nd the shutter is losed, the mhine nnot e threded. Be sure to rise the presser foot nd open the shutter efore threding the mhine. In ddition, efore removing the upper thred, e sure to rise the presser foot nd open the shutter. This mhine is equipped with window tht llows you to hek the position of the tke-up lever. Look through this window nd hek tht the thred is orretly fed through the tke-up lever. Thred guide over i Pss the thred under the thred guide plte, nd then pull it up. j Thred guide plte While using your right hnd to lightly hold the thred pssed under the thred guide plte, pss the thred through the thred pth in the order shown elow. k Pss the thred ehind the needle r thred guide. The thred n esily e pssed ehind the needle r thred guide y holding the thred in your left hnd, then feeding the thred with your right hnd, s shown. Needle r thred guide Shutter Next, use the needle threder to thred the needle. Continue with the proedure in Threding the needle (pge 34). Upper Threding 33

36 GETTING READY Threding the needle This setion desries how to thred the needle. Memo The needle threder n e used with sewing mhine needles 75/ through 00/6. The needle threder nnot e used with the wing needle or the twin needle. If the needle threder nnot e used, refer to Threding the needle mnully (without using the needle threder) (pge 35). Note If the thred is pulled through nd nnot e ut orretly, lower the presser foot so tht the thred is held in ple efore utting the thred. If this opertion is performed, skip step. When using thred tht quikly winds off the spool, suh s metlli thred, it my e diffiult to thred the needle if the thred is ut. Therefore, insted of using the thred utter, pull out out 80 mm (pprox. 3 inhes) of thred fter pssing it through the thred guide disks (mrked 7 ). Pull the end of the thred, whih hs een pssed through the needle r thred guide, to the left, then pss the thred through the noth of the thred guide, nd then firmly pull the thred from the front nd insert it into the slit of the thred guide disk mrked "7" ll the wy 2. Mke sure tht the thred psses the noth of the thred guide. 80 mm (3 inhes) or more Lower the presser foot lever to lower the presser foot. 2 Noth of the thred guide Thred guide disk Presser foot lever 2 d Lower the needle threder lever on the left side of the mhine until it liks, nd then slowly return the lever to its originl position. Cut the thred with the thred utter on the left side of the mhine. Thred utter Needle threder lever The thred is pssed through the eye of the needle. 34

37 Note If the needle ws not ompletely threded, ut loop in the thred ws formed in the eye of the needle, refully pull the loop through the eye of the needle to pull out the end of the thred. CAUTION When pulling out the thred, do not pull it with extreme fore, otherwise the needle my rek or end. Threding the needle mnully (without using the needle threder) When using speilty thred, suh s trnsprent nylon thred or metlli thred, wing needle or twin needle whih nnot e used with the needle threder, thred the needle s desried elow. Thred the mhine to the needle r thred guide. For detils, refer to Upper Threding (pge 3). Lower the presser foot lever. e Rise the presser foot lever, pss the end of the thred through the presser foot, nd then pull out out 5 m (2 inhes) of thred towrd the rer of the mhine. Pressor foot lever Pss the thred through the eye of the needle from front to k. 5 m (2 inhes) The upper threding is finished. Now tht the upper threding nd the lower threding re finished, you re redy to egin sewing. Note If the needle is not rised, the needle threder nnot thred the needle. Be sure to press ( Needle Position utton) to rise the needle efore using the needle threder. CAUTION Do not touh the ( Strt/Stop utton), ( Needle Position utton) or ( Reverse/Reinforement stith utton). If one of the uttons is identlly pressed, the mhine will egin sewing nd your finger my e priked with the needle or the needle my rek. d Rise the presser foot lever, pss the end of the thred through the presser foot, nd then pull out out 5 m (2 inhes) of thred towrd the rer of the mhine. Upper Threding 35

38 GETTING READY Using the twin needle With the twin needle, you n sew two prllel lines of the sme stith with two different threds. Both upper threds should hve the sme thikness nd qulity. Be sure to use the twin needle, the extr spool pin nd the spool p. For detils on the stithes tht n e sewn with the twin needle, refer to Stith Setting Chrt (pge 70). d Insert the extr spool pin onto the oin winder shft. Insert the extr spool pin so tht it is perpendiulr to the oin winder shft. Boin winder shft e Swing down the spool pin so tht it is horizontl. CAUTION Only use the twin needle (prt ode: X ). Use of ny other needle my end the needle or dmge the mhine. Never use ent needles. Bent needles n esily rek, possily resulting in injuries. Instll the twin needle. For detils on instlling needle, refer to Repling the needle (pge 42). f Ple the upper thred spool for the needle on the right side onto the extr spool pin, nd then seure it with the spool p. The thred should unroll from the top front of the spool. Thred the upper thred for the left needle eye. For detils, refer to steps through k of Threding the upper thred (pge 32). Mnully thred the left needle with the upper thred. Pss the thred through the eye of the needle from the front. Spool p Spool 36 The needle threder nnot e used with the twin needle. If the needle threder is used with the twin needle, the sewing mhine my e dmged.

39 g Thred the upper thred for the right side in the sme wy tht the upper thred for the left side ws threded. Turn on the sewing mhine nd selet stith. j For stith seletion see Seleting stithing (pge 5). See Stith Setting Chrt (pge 70) for stithes tht use twin needle. Thred guide over For detils, refer to steps h through j of Threding the upper thred (pge 33). Without pssing the thred through the needle h r thred guide, mnully thred the right needle. Pss the thred through the eye of the needle from the front. Note When using the pintuk foot (sold seprtely) to sew stright pintuks with the twin needle, selet the stith with the enter needle position. CAUTION When using the twin needle, e sure to selet n pproprite stith, otherwise the needle my rek or the mhine my e dmged. After djusting the stith width, slowly turn the hndwheel towrd you (ounterlokwise) nd hek tht the needle does not touh the presser foot. If the needle hits the presser foot, the needle my end or rek. The needle threder nnot e used with the twin needle. If the needle threder is used with the twin needle, the sewing mhine my e dmged. Atth zigzg foot J. i For detils on hnging the presser foot, refer to Repling the Presser Foot (pge 44). CAUTION When using the twin needle, e sure to tth zigzg foot J. If unhed stithes our, use presser foot N or tth stilizer mteril. Press. k The sreen for setting the twin needle ppers. Upper Threding 37

40 GETTING READY Press. l displys in reverse highlight. If pressed gin, it returns to. CAUTION When hnging the sewing diretion, press ( Needle Position utton) to rise the needle from the fri, nd then rise the presser foot lever nd turn the fri. Otherwise the needle my rek or the mhine my e dmged. Do not try turning the fri with the twin needle left down in the fri, otherwise the needle my rek or the mhine my e dmged. m Press The twin needle n now e used. (Bk key). The initil sreen ppers gin, nd ppers. CAUTION When using the twin needle, e sure to selet the twin needle setting, otherwise the needle my rek or the mhine my e dmged. Strt sewing. n For detils on strting to sew, refer to Strting to sew (pge 53). Two lines of stithing re sewn prllel to eh other. 38

41 Pulling up the oin thred When mking gthers or efore free-motion quilting, first pull up the oin thred s desried elow. Insert the oin into the oin se. Refer to steps through g of Instlling the oin (pge 29). Pss the oin thred through the slot. Do not ut the thred with the utter. e Pull out out 0 m (4 inhes) of the oin thred under the presser foot towrd the rer of the mhine. f Retth the oin over. Insert the t in the lower-left orner of the oin over, nd then lightly press down on the right side. While lightly holding the upper thred with your left hnd with the needle in the upposition, press ( Needle Position utton) twie to lower nd rise the needle. d Needle Position utton The oin thred is looped round the upper thred nd n e pulled up. Crefully pull the upper thred upwrd to pull out the end of the oin thred. Upper Threding 39

42 GETTING READY Repling the Needle This setion desries how to reple the needle. Needle preutions Be sure to oserve the following preutions onerning the hndling of the needle. Filure to oserve these preutions is extremely dngerous, for exmple, if the needle reks nd frgments re dispersed. Be sure to red nd refully follow the instrutions elow. CAUTION Only use home sewing mhine needles. Use of ny other needle my end the needle or dmge the mhine. Never use ent needles. Bent needles n esily rek, possily resulting in injuries. 40

43 Needle types nd their uses The sewing mhine needle tht should e used depends on the fri nd thred thikness. Refer to the following tle when hoosing the thred nd needle pproprite for the fri tht you wish to sew. Thred Fri Type/Applition Size of Needle Type Size Brodloth Cotton thred Medium weight Tffet Syntheti thred 75/ 90/4 fris Flnnel, Grdine Silk thred 50 Lwn Cotton thred Thin fris Georgette Syntheti thred 65/9 75/ Chllis, Stin Silk thred /6 Denim Cotton thred 50 Thik fris Corduroy Syntheti thred 90/4 00/ Tweed Silk thred Jersey Bll point needle Streth fris Thred for knits / 90/4 Triot (golden olored) Cotton thred Esily fryed fris Syntheti thred 65/9 90/4 Silk thred 50 Syntheti thred 30 00/6 For top-stithing Silk thred / 90/4 Note Never use thred of weight 20 or lower. It my use mlfuntions. Thred nd needle numer The lower the thred numer is, the lrger the thred, nd the lrger the needle numer, the lrger the needle. Bll point needle (gold olored) To void skipped stithes use ll point needles with streth fris. Trnsprent nylon thred Use 90/4 to 00/6 needle, regrdless of the fri or thred. Emroidery needles Use 75/ home sewing mhine needle. When emroidering on thik fris suh s denim, use 90/4 or 00/6 home sewing mhine needle. CAUTION The pproprite fri, thred nd needle omintions re shown in the tle ove. If the omintion of the fri, thred nd needle is not orret, prtiulrly when sewing thik fris (suh s denim) with thin needles (suh s 65/9 to 75/), the needle my end or rek. In ddition, the stithing my e uneven or pukered or there my e skipped stithes. Repling the Needle 4

44 GETTING READY Cheking the needle Sewing with ent needle is extremely dngerous sine the needle my rek while the mhine is eing operted. Before using the needle, ple the flt side of the needle on flt surfe nd hek tht the distne etween the needle nd the flt surfe is even. Repling the needle Reple the needle s desried elow. Use the srewdriver nd needle tht hs een determined to e stright ording to the instrutions in Cheking the needle. Press ( Needle Position utton) one or twie to rise the needle. Needle Position utton Flt side Needle type mrking Turn off the sewing mhine. CAUTION If the distne etween the needle nd the flt surfe is not even, the needle is ent. Do not use ent needle. CAUTION Before repling the needle, e sure to turn off the sewing mhine, otherwise injuries my our if ( Strt/Stop utton) is identlly pressed nd the mhine strts sewing. Ple fri or pper under the presser foot to over the hole in the needle plte. Flt surfe Note Before repling the needle, over the hole in the needle plte with fri or pper to prevent the needle from flling into the mhine. Lower the presser foot lever. d Presser foot lever 42

45 e Hold the needle with your left hnd, nd then use srewdriver to turn the needle lmp srew towrd you (ounterlokwise) to remove the needle. While holding the needle with your left hnd, g use the srewdriver to tighten the needle lmp srew. 2 Instll the twin needle in the sme wy. f Srewdriver Needle lmp srew Do not pply strong fore when loosening or tightening the needle lmp srew, otherwise ertin prts of the sewing mhine my e dmged. With the flt side of the needle towrd the rer of the mhine, insert the needle until it touhes the needle stopper. CAUTION Be sure to insert the needle until it touhes the needle stopper nd seurely tighten the needle lmp srew with the srewdriver, otherwise the needle my rek or dmge my result. Needle stopper Repling the Needle 43

46 GETTING READY Repling the Presser Foot This setion desries how to reple the presser foot. Presser foot preutions Be sure to oserve the following preutions onerning the presser feet. CAUTION Use the presser foot pproprite for the type of stith tht you wish to sew, otherwise the needle my hit the presser foot, using the needle to end or rek. Only use presser feet designed speifilly for this sewing mhine. Use of ny other presser foot my result in injuries or dmge to the mhine. Repling the presser foot Rise the presser foot lever. Reple the presser foot s desried elow. Press ( Needle Position utton) one or twie to rise the needle. d Presser foot lever The presser foot is rised. Press the lk utton t the k of the presser foot holder. Needle Position utton Turn off the sewing mhine. CAUTION Before repling the presser foot, e sure to turn off the sewing mhine, otherwise injuries my our if ( Strt/Stop utton) is identlly pressed nd the mhine strts sewing. Blk utton Presser foot holder The presser foot holder releses the presser foot. 44

47 e Ple different presser foot elow the holder so tht the presser foot pin is ligned with the noth in the holder. Position the presser foot so the letter inditing the presser foot type (A, G, I, J, M, N or R) is positioned to e red. Rise the presser foot lever to hek tht the g presser foot is seurely tthed. f 2 3 Presser foot holder Noth Pin d Presser foot type Slowly lower the presser foot lever so tht the presser foot pin snps into the noth in the presser foot holder. J 4 Note When stith is seleted, the ion for the presser foot tht should e used ppers in the sreen. Chek tht the orret presser foot is tthed efore strting to sew. If the wrong presser foot is instlled, turn off the sewing mhine, tth the orret presser foot, nd then selet the desired stith gin. d Buttonhole foot A Oversting foot G Zigzg foot J Button fitting foot M Presser foot lever Presser foot holder Noth d Pin The presser foot is tthed. Monogrmming foot N Blind stith foot R Side utter S For detils on the presser foot tht should e used with the seleted stith, refer to Stith Setting Chrt (pge 70). Repling the Presser Foot 45

48 GETTING READY Removing nd tthing the presser foot holder Remove the presser foot holder when lening the sewing mhine or when instlling presser foot tht does not use the presser foot holder, suh s the emroidery foot nd optionl quilting foot. Use the srewdriver to remove the presser foot holder. Remove the presser foot. For detils, refer to Repling the presser foot (pge 44). Use the srewdriver to loosen the presser foot holder srew. Hold the presser foot holder in ple with your right hnd, nd then tighten the srew using the srewdriver in your left hnd. Srewdriver Note If the presser foot holder is not orretly instlled, the thred tension will e inorret. Srewdriver Presser foot holder Presser foot holder srew Atthing the presser foot holder Rise the presser foot lever. Align the presser foot holder with the lowerleft side of the presser r. 46

49 Sewing Cylindril Piees Free-rm sewing mkes sewing ylindril piees esy. Free-rm sewing Removing the flt ed tthment llows for free-rm sewing, mking it esier to sew ylindril piees suh s sleeve uffs nd pnt legs. Pull the flt ed tthment off to the left. With the flt ed tthment removed, freerm sewing is possile. Slide the prt tht you wish to sew onto the rm, nd then sew from the top. When you re finished with free-rm sewing, instll the flt ed tthment k in its originl position. Sewing Cylindril Piees 47

50 GETTING READY 48

51 2 SEWING BASICS The neessry preprtions for sewing re desried in this hpter. Sewing...50 Generl sewing proedure...50 Seleting stithing...5 Positioning the fri...52 Strting to sew...53 Seuring the stithing...55 Cutting the thred...56 Setting the Stith...58 Adjusting the stith width...58 Adjusting the stith length...59 Adjusting the thred tension...59 Useful Funtions...6 Automtilly sewing reverse/reinforement stithes...6 Automtilly utting the thred...62 Mirroring stithes...63 Useful Sewing Tips...64 Tril sewing...64 Chnging the sewing diretion...64 Sewing urves...64 Adjusting the presser foot pressure...64 Sewing thik fris...65 Sewing thin fris...66 Sewing streth fris...66 Sewing lethers or vinyl fris...66 Sewing n even sem llowne...66 Hnds-free rising nd lowering of the presser foot...67 Sewing hook-nd-loop fstener...68

52 SEWING BASICS Sewing Bsi sewing opertions re desried elow. Before operting the sewing mhine, red the following preutions. CAUTION While the mhine is in opertion, py speil ttention to the needle lotion. In ddition, keep your hnds wy from ll moving prts suh s the needle nd hndwheel, otherwise injuries my our. Do not pull or push the fri too hrd while sewing, otherwise injuries my our or the needle my rek. Never use ent needles. Bent needles n esily rek, possily resulting in injuries. Mke sure tht the needle does not strike sting pins, otherwise the needle my rek or end. Generl sewing proedure Follow the si proedures elow to sew. Turn on the mhine. 2 Selet the stith. 3 Atth the presser foot. 4 Position the fri. 5 Strt sewing. 6 Cut the thred. Turn on the sewing mhine. For detils on turning on the mhine, refer to Turning on the mhine (pge 9). Selet the stith pproprite for the re to e sewn. For detils on seleting stith, refer to Seleting stithing (pge 5). Atth the presser foot pproprite for the stith. (Be sure to turn off the mhine efore repling the presser foot.) For detils on repling the presser foot, refer to Repling the presser foot (pge 44). Ple the re to e sewn under the presser foot. Be sure tht the fri piees re sewn in the orret order nd tht the right nd wrong sides of the fri re ligned orretly. For detils on positioning the fri, refer to Positioning the fri (pge 52). Strt sewing. For detils on strting to sew, refer to Strting to sew (pge 53). Cut the thred t the end of sewing. For detils on utting the thred, refer to Cutting the thred (pge 56). 50

53 Seleting stithing Stithes re seleted using LCD opertions. There re 7 utility stithes. Right fter turning the power on, the stright stith (left needle position) is seleted. The mhine n lso e set to selet the stright stith (enter needle position). For detils on hnging the setting, refer to pge 2. Determine the stith to e used, nd get the mthing presser foot redy. Refer to Stith Setting Chrt (pge 70). Atth the presser foot. The mhine omes with zigzg foot J tthed. For detils, refer to Repling the presser foot (pge 44). CAUTION Use the presser foot pproprite for the stith. If the wrong presser foot is used, the needle my hit the presser foot nd rek or end. Turn on the sewing mhine. The stright stith (left needle position) is shown seleted in the LCD. When n nimtion is displyed on the sreen, touh the sreen with your finger. Selet stith. d (Previous pge key) displys the previous sreen, nd (Next pge key) displys the next sreen. e Exmple: is seleted: The stith is seleted, nd the stith numer nd settings re displyed. If neessry, speify the setting for utomti reverse/reinforement stithing nd djust the stith length, et. Memo Uses of stithes nd other stith seletions re explined in UTILITY STITCHES (pge 69). Automti reverse/reinforement stithing nd other settings re explined in Useful Funtions (pge 6). The proedures for speifying the thred tension re desried in Adjusting the thred tension (pge 59). Proedures for hnging the stith width nd length re desried in Adjusting the stith width (pge 58) nd Adjusting the stith length (pge 59). Note When stith is seleted, the ion for the presser foot tht should e used ppers on the sreen. For detils, refer to Repling the presser foot (pge 44). Chek tht the orret presser foot is tthed efore strting to sew. If the wrong presser foot is instlled, turn off the sewing mhine, tth the orret presser foot, nd then selet the desired stith gin. 2 Sewing 5

54 SEWING BASICS Positioning the fri Be sure tht the fri piees re sewn in the orret order nd tht the right nd wrong sides of the fri re ligned orretly. d While holding the end of the thred nd the fri with your left hnd, turn the hndwheel towrd you (ounterlokwise) with your right hnd to lower the needle to the strting point of the stithing. Turn on the sewing mhine. Press ( Needle Position utton) one or twie to rise the needle. Needle Position utton Ple the fri under the presser foot. If the sem llowne is positioned on the right side, sewing in stright line is esier nd the extr fri does not get in the wy. Lower the presser foot lever. e Presser foot lever The fri is now positioned to e sewn. 52

55 Strting to sew One you re redy to strt sewing, you n strt the sewing mhine. The sewing speed n e djusted using either the sewing speed ontroller or the foot ontroller. Note When the foot ontroller is plugged in, ( Strt/Stop utton) nnot e used to strt sewing. Using the opertion utton Sewing n e strted nd stopped using the opertion utton ( Strt/Stop utton). Slide the sewing speed ontroller to the left or right to selet the desired sewing speed. Slide the sewing speed ontroller to the left to sew t slower speed, or slide the speed ontroller to the right to sew t fster speed. If you ontinue to hold the ( Strt/Stop utton) pressed immeditely fter the sewing strts, the mhine will sew t slow speed. When the end of the stithing is rehed, press ( Strt/Stop utton) one. The mhine stops sewing with the needle down (in the fri). When you hve finished sewing, press d ( Needle Position utton). The needle is rised. Cut the threds. e For detils, refer to Cutting the thred (pge 56). 2 Sewing speed ontroller Note This mhine will utomtilly stop when the oin eomes lmost empty. When the mhine stops, reple the oin thred, nd then press ( Strt/Stop utton) to egin sewing gin. Press ( Strt/Stop utton) one. Using the foot ontroller Sewing n e strted nd stopped using the foot ontroller. Strt/Stop utton The mhine strts sewing. Turn off the sewing mhine. When onneting the foot ontroller, e sure to turn off the sewing mhine in order to prevent the mhine from identlly eing strted. Sewing 53

56 SEWING BASICS Insert the foot ontroller plug into its jk on the right side of the sewing mhine. When the end of the stithing is rehed, f ompletely relese the foot ontroller. The mhine stops sewing with the needle lowered (in the fri). When you hve finished sewing, press g ( Needle Position utton). The needle is rised. Foot ontroller jk Turn on the sewing mhine. Slide the sewing speed ontroller to the left or d right to selet the foot ontroller's mximum sewing speed. Slide the sewing speed ontroller to the left to selet lower mximum sewing speed, or slide the speed ontroller to the right to selet higher mximum sewing speed. Cut the threds. h For detils, refer to Cutting the thred (pge 56). Memo When the foot ontroller is plugged in, ( Strt/Stop utton) nnot e used to strt sewing. When sewing is stopped, the needle remins lowered (in the fri). The mhine n e set so tht the needle will sty up when sewing is stopped. For detils on setting the mhine so tht the needle stys up when sewing is stopped, refer to Chnging the mhine settings (pge 2). Sewing speed ontroller The speed set using the sewing speed ontroller will e the foot ontroller s mximum sewing speed. One you re redy to strt sewing, slowly e press down on the foot ontroller. Pressing down on the foot ontroller inreses the sewing speed; relesing the pressure on the foot ontroller dereses the sewing speed. CAUTION Do not llow thred or dust to umulte in the foot ontroller, otherwise fire or n eletri shok my our. Do not ple ojets on the foot ontroller, otherwise dmge to the mhine or injuries my our. If the mhine is not to e used for long period of time, unplug the foot ontroller, otherwise fire or n eletri shok my our. Slower Fster Slowly press down on the foot ontroller. Pressing it down hrd strts sewing too quikly. The mhine strts sewing. 54

57 Seuring the stithing When sewing with the stright stith, for exmple, t the end of n opening or where sems do not overlp, use reverse stithing or reinforement stithing to seure the end of the thred. Lower the needle into the fri t the eginning of the stithing, nd then lower the presser foot lever. Press ( Strt/Stop utton) or press down on the foot ontroller. At this time, if ( Strt/Stop utton) is held down, the mhine sews t slow speed. Reverse/Reinforement Stith utton While ( Reverse/Reinforement Stith utton) is held down, reverse stithes re sewn. After sewing k to the eginning of the d stithing, relese ( Reverse/Reinforement Stith utton). The mhine stops sewing. Press ( Strt/Stop utton), or press down e on the foot ontroller. The mhine strts sewing in the norml sewing diretion. 2 Strt/Stop utton For detils, refer to Strting to sew (pge 53). The mhine strts sewing. After sewing 3 to 5 stithes, press ( Reverse/Reinforement Stith utton). Keep ( Reverse/Reinforement Stith utton) held down until you reh the eginning of the stithing. The mhine sews t slow speed when ( Reverse/Reinforement Stith utton) is held down. When the end of the stithing is rehed, press f ( Reverse/Reinforement Stith utton). Keep ( Reverse/Reinforement Stith utton) held down until 3 to 5 reverse stithes re sewn. While ( Reverse/Reinforement Stith utton) is held down, reverse stithes re sewn. Sewing 55

58 SEWING BASICS After 3 to 5 reverse stithes hve een sewn, g relese ( Reverse/Reinforement Stith utton). The mhine stops sewing. Press ( Strt/Stop utton), or press down h on the foot ontroller. At this time, if ( Strt/Stop utton) is held down, the mhine sews t slow speed. The mhine strts sewing in the norml sewing diretion. After sewing to the end of the stithing, the i sewing mhine stops. Press ( Strt/Stop utton) or relese foot ontroller. 3 2 Cutting the thred When you hve finished sewing, ut the threds. Using ( Thred Cutter utton) When you wish to finish the stithing, press ( Thred Cutter utton) one. Thred Cutter utton The threds re ut nd the needle is rised. Rise the presser foot lever, then remove the fri. 4 2 Beginning of stithing End of stithing Sewing stithes Reverse stithes re preset for the 3 nd 7 stithes. When ( Reverse/Reinforement Stith utton) is pressed with stithes other thn these, reinforement stithes re used. Reinforement stithes re 3 to 5 stithes sewn on top of eh other in one ple. 2 Reverse stithing Reinforement stithing Memo The sewing mhine n e set to utomtilly sew reverse or reinforement stithes t the eginning nd end of the stithing. For detils, refer to Automtilly sewing reverse/ reinforement stithes (pge 6). 5 6 Presser foot lever CAUTION Do not press ( Thred Cutter utton) fter threds hve lredy een ut, otherwise the needle my rek, the threds my eome tngled or dmge to the mhine my our. Do not press ( Thred Cutter utton) if there is no fri under the presser foot or while the mhine is sewing, otherwise dmge to the mhine my our. Memo The mhine n e set so tht the threds will e ut when sewing is finished. For detils on setting the mhine so tht the threds re ut utomtilly, refer to Automtilly utting the thred (pge 62). 56

59 Using the thred utter When sewing with nylon or metlli threds, or other speil threds, use the thred utter on the side of the mhine to ut the threds. When you wish to finish the stithing nd the sewing mhine is stopped, press ( Needle Position utton) one to rise the needle. 2 Needle Position utton The needle is rised. Rise the presser foot lever. Presser foot lever Pull the fri to the left side of the mhine, nd then pss the threds through the thred utter to ut them. Thred utter Sewing 57

60 SEWING BASICS Setting the Stith This mhine is preset with the defult settings for the stith width, stith length, nd upper thred tension for eh stith. However, you n hnge ny of the settings y pressing in the sreen, then following the proedure desried in this setion. Note If the thred tension nnot e djusted s desired, refer to List of symptoms (pge 97). Settings for some stithes nnot e hnged. For detils, refer to Stith Setting Chrt (pge 70). Stith settings return to their defults if they re hnged, when the mhine is turned off or different stith is seleted efore the stith setting is sved. Adjusting the stith width The stith width (zigzg width) n e djusted to mke the stith wider or nrrower. Eh press of mkes the zigzg stith nrrower. Memo Press to return the setting to its defult. If the stright stith (left needle position or triple streth stith) ws seleted, hnging the stith width hnges the needle position. Inresing the width moves the needle to the right; reduing the width moves the needle to the left. The sewing mhine n e set so tht the stith width n esily e hnged with the sewing speed ontroller. For detils, refer to Stin stithing using the sewing speed ontroller (pge ). mens the setting nnot e djusted. Eh press of mkes the zigzg stith wider. CAUTION After djusting the stith width, slowly turn the hndwheel towrd you (ounterlokwise) nd hek tht the needle does not touh the presser foot. If the needle hits the presser foot, the needle my end or rek. 58

61 Adjusting the stith length The stith length n e djusted to mke the stith longer or shorter. Adjusting the thred tension You my need to hnge the thred tension, depending on the fri nd thred eing used. Eh press of mkes the stith shorter. Corret thred tension The upper thred nd the oin thred should ross ner the enter of the fri. Only the upper thred should e visile from the right side of the fri, nd only the oin thred should e visile from the wrong side of the fri. 2 Eh press of mkes the stith longer. d Wrong side of fri Right side of fri Upper thred Boin thred Memo Press to return the setting to its defult. mens the setting nnot e djusted. CAUTION If the stithes re unhed together, inrese the stith length. Continuing to sew with the stithes unhed together my result in the needle ending or reking. Setting the Stith 59

62 SEWING BASICS Upper thred is too tight If the oin thred is visile from the right side of the fri, the upper thred is too tight. Upper thred is too loose If the upper thred is visile from the wrong side of the fri, the upper thred is too loose. Note If the oin thred ws inorretly threded, the upper thred my e too tight. In this se, refer to Instlling the oin (pge 29) nd rethred the oin thred. Note If the upper thred ws inorretly threded, the upper thred my e too loose. In this se, refer to Upper Threding (pge 3) nd rethred the upper thred. Wrong side of fri Right side of fri Upper thred d Boin thred e The oin thred is visile from the right side of the fri. Eh press of mkes the thred tension looser. Wrong side of fri Right side of fri Upper thred d Boin thred e The upper thred is visile from the wrong side of the fri. Eh press of mkes the thred tension tighter. Memo Press defult. to return the setting to its Note If the upper thred is not threded orretly or the oin is not instlled orretly, it my not e possile to set the orret thred tension. If the orret thred tension nnot e hieved, rethred the upper thred nd insert the oin orretly. 60

63 Useful Funtions Funtions useful in improving sewing effiieny re desried elow. Automtilly sewing reverse/ reinforement stithes d Position the fri under the presser foot, nd then press ( Strt/Stop utton) one. The sewing mhine n e set to utomtilly sew reverse or reinforement stithes t the eginning nd end of the stithing. Whether reverse stithes or reinforement stithes re sewn depends on the stith tht is seleted. For detils, refer to Stith Setting Chrt (pge 70). Turn on the sewing mhine. The LCD omes on. Selet stith. For detils on seleting stith, refer to Seleting stithing (pge 5). Press on the LCD. This step is not neessry if stith suh s those for sewing uttonholes nd r tks is seleted where reinforement stithes re utomtilly sewn. e Strt/Stop utton After reverse/reinforement stithes re sewn, the mhine strts sewing. After rehing the end of the stithing, press ( Reverse/Reinforement Stith utton) one. This step is not neessry if stith suh s those for sewing uttonholes nd r tks is seleted where reinforement stithes re utomtilly sewn. Reverse/Reinforement Stith utton After reverse/reinforement stithes re sewn, the sewing mhine stops. 2 It turns to, nd the sewing mhine is set for utomti reverse/reinforement stithing. To turn utomti reverse/reinforement stithing off, press. When the sewing mhine is turned off, the utomti reverse/reinforement stithing setting is nelled. Memo Reverse/reinforement stithes WILL NOT e sewn until ( Reverse/Reinforement Stith utton) is pressed. ( Strt/Stop utton) my e pressed to stop stithing when needed suh s for pivoting orners. Useful Funtions 6

64 SEWING BASICS Automtilly utting the thred The sewing mhine n e set to utomtilly ut the threds t the end of the stithing. This is lled progrmmed thred-utting. If progrmmed thredutting is set, utomti reverse/reinforement stithing is lso set. Turn on the sewing mhine. Set the fri in ple, nd press d Stop utton) one. ( Strt/ Strt/Stop utton Stithing strts fter reverse stithing or reinforement stithing. The LCD omes on. Selet stith. For detils on seleting stith, refer to Seleting stithing (pge 5). Press on the sreen. One you hve rehed the end of the e stithing, press ( Reverse/Reinforement Stith utton) one. If stithing, suh s uttonholes nd r tking, tht inludes reinforement stithing hs een seleted, this opertion is unneessry. After the reverse stithing or reinforement stithing hs een done, the sewing mhine stops, nd the thred is ut. You get, nd the sewing mhine is set for progrmmed thred-utting nd utomti reverse/reinforement stithing. The thred is ut here. To turn progrmmed thred utting off, press. Memo Reverse/reinforement stithes WILL NOT e sewing nd the thred will not utomtilly e ut until ( Reverse/ Reinforement Stith utton) is pressed. ( Strt/Stop utton) my e pressed to stop stithing when needed suh s for pivoting orners. If the power is turned off, progrmmed thred-utting will e turned off. 62

65 Mirroring stithes You n sew the mirror imge of stith horizontlly (left nd right). Turn on the sewing mhine. The LCD omes on. 2 Selet stith. For detils on seleting stith, refer to Seleting stithing (pge 5). Press on the sreen. It turns to, nd the pttern displyed t the top of the sreen is mirrored. To turn the mirrored stithing off, press. Memo Mirroring is not possile for uttonholes nd other stithes where shows. When the sewing mhine is turned off, the mirroring setting is nelled. Useful Funtions 63

66 SEWING BASICS Useful Sewing Tips Vrious wys to hieve etter results for your sewing projets re desried elow. Refer to these tips when sewing your projet. Tril sewing After you hve set up the mhine with the thred nd needle pproprite for the type of fri eing sewn, the mhine utomtilly sets the thred tension nd stith length nd width for the stith tht is seleted. However, tril piee of fri should e sewn sine, depending on the type of fri nd stithing eing sewn, the desired results my not e hieved. For the tril sewing, use piee of fri nd thred tht re the sme s those used for your projet, nd hek the thred tension nd stith length nd width. Sine the results differ depending on the type of stithing nd the numer of lyers of fri sewn, perform the tril sewing under the sme onditions tht will e used with your projet. Chnging the sewing diretion When the stithing rehes orner, stop the sewing mhine. Leve the needle lowered (in the fri). If the needle remined up when the mhine stopped sewing, press ( Needle Position utton) to lower the needle. Rise the presser foot lever, nd then turn the fri. Turn the fri using the needle s pivot. Sewing urves Stop sewing, nd then slightly hnge the sewing diretion to sew round the urve. For detils on sewing with n even sem llowne, refer to Sewing n even sem llowne (pge 66). When sewing long urve while using zigzg stith, selet shorter stith length in order to otin finer stith. Adjusting the presser foot pressure The presser foot pressure (the mount of pressure pplied to the fri y the presser foot) n e djusted. Lower the presser foot lever to lower the presser foot. Presser foot lever Lower the presser foot lever nd ontinue sewing. 64

67 Turn the presser foot pressure dil t the k of the mhine to djust the pressure of the presser foot. The sle on the dil indites the rnge from (wek) to 4 (strong). Turn the dil to the right (smller numer) to derese the pressure. Turn the dil to the left (lrger numer) to inrese the pressure. Sewing diretion Rise the presser foot lever. Align the eginning of stithing, nd then position the fri. 2 Strong Wek While holding zigzg foot J level, hold the presser foot loking pin (lk utton on the left side) pressed in, nd lower the presser foot lever. When you re finished sewing, reset the dil to 3 (stndrd). Sewing thik fris If the fri does not fit under the presser foot If the fri does not fit esily under the presser foot, rise the presser foot lever even higher to ring the presser foot to its highest position. Presser foot holding pin (lk utton) Relese the presser foot loking pin (lk d utton). The presser foot remins level, llowing the fri to e fed. If thik sems re eing sewn nd the fri does not feed t the eginning of stithing The fri my not feed when thik sems re eing sewn nd the presser foot is not level, s shown elow. In this se, use the presser foot loking pin (lk utton on the left side of zigzg foot J ) so tht the presser foot remins level while sewing, llowing the fri to e fed smoothly. After the sem is sewn, the presser foot will return to its originl ngle. CAUTION If fri more thn 6 mm (5/64 inh) thik is sewn or if the fri is pushed with too muh fore, the needle my end or rek. Useful Sewing Tips 65

68 SEWING BASICS Sewing thin fris When sewing thin fris, the stithing my eome misligned or the fri my not feed orretly. If this ours, ple thin pper or stilizer mteril under the fri nd sew it together with the fri. When you hve finished sewing, ter off ny exess pper. Sewing n even sem llowne To sew n even sem, strt sewing so tht the sem llowne is to the right of the presser foot, nd the edge of the fri is ligned with either the right edge of the presser foot or mrking on the needle plte. Aligning the fri with the presser foot Sew while keeping the right edge of the presser foot fixed distne from the edge of the fri. Stilizer mteril or pper Sewing streth fris First, ste the piees of fri together, nd then sew without strething the fri. Sem Presser foot Aligning the fri with the stith guide foot Sew while keeping the right edge of the fri ligned with desired position of mrkings on the stith guide foot. Bsting For est results when sewing on knit fris use the streth stithes reommended elow. Also e sure to use needle for knits Sem Stith guide foot Mrkings Sewing lethers or vinyl fris When sewing the fris tht my stik to the presser foot suh s lethers or oted fris, hnge the presser foot to the non stik foot. Lether 66

69 Aligning the fri with needle plte mrking The mrkings on the needle plte show the distne from the needle position of sem sewn with the stright stith (left needle position). Sew while keeping the edge of the fri ligned with mrking in the needle plte. The distne etween the mrkings in the upper sle is /8 inh (3 mm) nd the distne etween the mrkings in the grid is 5 mm (3/6 inh). Hnds-free rising nd lowering of the presser foot Using the knee lifter, you n rise nd lower the presser foot with your knee, leving oth hnds free to hndle the fri. Instlling the knee lifter Turn off the sewing mhine. 2 6 d e f Sem Presser foot Centimeters Inhes Needle plte.6 m (5/8 inh) Insert the knee lifter into the mounting slot on the front of the sewing mhine in the lowerright orner. Align the ts on the knee lifter with the nothes in the mounting slot, nd then insert the knee lifter s fr s possile. Ts Nothes Note If the knee lifter is not fully inserted into the mounting slot, it my fll out while the sewing mhine is operting. Useful Sewing Tips 67

70 SEWING BASICS Using the knee lifter Stop the sewing mhine. Do not use the knee lifter while the sewing mhine is operting. With your knee, press the knee lifter to the right. Keep the knee lifter pressed to the right. Sewing hook-nd-loop fstener CAUTION Use only the ungummed hook-nd-loop fstener whih is for sewing. If the glue is tthed to the needle or the oin hook re, it my use mlfuntion. If the hook-nd-loop fstener is sewn with the thin needle (65/9-75/), the needle my end or rek. Note Before strt sewing, ste together the fri nd the hook-nd-loop fstener. The presser foot is rised. Relese the knee lifter. The presser foot is lowered. CAUTION While sewing, keep your knee wy from the knee lifter. If the knee lifter is pressed while the sewing mhine is operting, the needle my rek or the mhine my e dmged. Mke sure tht the needle psses through the hooknd-loop fstener y turning the hndwheel nd lower the needle into the hook-nd-loop fstener efore sewing. And then, sew the edge of the hooknd-loop fstener t slow speed. If the needle does not pss through the hook-ndloop fstener, reple the needle with the needle for thik fris (pge 4). Edge of the hook-nd-loop fstener 68

71 3 UTILITY STITCHES The vrious stithes nd their pplitions re desried in this hpter. Stith Setting Chrt...70 Utility stithes...70 Other stithes...74 Seleting Stithing...77 Stith types...77 Seleting stithing...77 Sving stith settings...79 Oversting Stithes...8 Sewing oversting stithes using oversting foot G...8 Sewing oversting stithes using zigzg foot J...82 Sewing oversting stithes using the optionl side utter...83 Bsi Stithing...85 Bsting...85 Bsi stithing...85 Blind Hem Stithing...87 Buttonhole Stithing/Button Sewing...89 Buttonhole sewing...90 Button sewing...94 Zipper Insertion...96 Inserting entered zipper...96 Inserting side zipper...98 Zipper/piping Insertion...0 Inserting entered zipper...0 Inserting piping...02 Sewing Streth Fris nd Elsti Tpe...03 Streth stithing...03 Elsti tthing...03 Appliqué, Pthwork nd Quilt Stithing Appliqué stithing...06 Pthwork (rzy quilt) stithing..07 Pieing...07 Quilting...09 Free-motion quilting...0 Stin stithing using the sewing speed ontroller... Reinforement Stithing...3 Triple streth stithing...3 Br tk stithing...3 Drning...5 Eyelet Stithing...7 Horizontl Stithing...8 Deortive Stithing...20 Fgoting...2 Sllop stithing...22 Smoking...22 Shell tuk stithing...23 Joining...24 Heirloom stithing...25 Sewing the Vrious Built-in Deortive Ptterns...28 Sewing eutiful ptterns...28 Sewing ptterns...28 Chnging the pttern size...29 Chnging the stith density...29 Chnging the length for stin stithes...30 Shifting ptterns...3 Comining ptterns...32 Sving ptterns...35 Religning the pttern...36 Designing Pttern (My Custom Stith)...39 Drwing sketh of the pttern...39 Entering the pttern dt...40 Exmples of designs...42

72 UTILITY STITCHES Stith Setting Chrt Applitions, stith lengths nd widths nd whether the twin needle n e used re listed for utility stithes in the following tle. Utility stithes Stith Nme Pttern Presser Foot Applition Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul Twin Needle Reverse/ Reinforement Stithing Wlking Foot J Bsi stithing, sewing gthers or pintuks, et. 0.0 (0) (0 /4) 2.5 (3/32) (/64 3/6) Yes (J) Reverse No Stright stith Left 2 J Bsi stithing nd sewing gthers or pintuks 0.0 (0) (0 /4) 2.5 (3/32) (/64 3/6) Yes (J) Reinforement Yes Center 3 J/I Atthing zippers, si stithing, sewing gthers or pintuks, et. 3.5 (/8) (0 /4) 2.5 (3/32) (/64 3/6) Yes (J) Reverse No Triple streth stith 4 J Atthing sleeves, sewing insems, sewing streth fris nd deortive stithing 0.0 (0) (0 /4) 2.5 (3/32) (/6 3/6) Yes (J) Reinforement No Streth stith 5 J Sewing streth fris nd deortive stithing.0 (/6) (/6 /8) 2.5 (3/32) (/6 3/6) Yes (J) Reinforement No Bsting stith 6 J Temporrily seuring 0.0 (0) (0 /4) 20 (3/4) 5 30 (3/6-3/6) No Reinforement No Zigzg stith Center Right 7 8 J J Oversting nd tthing ppliqués Beginning sewing from the right needle position 3.5 (/8) 3.5 (/8) (0 /4) (3/32 3/6).4 (/6).4 (/6) (0 3/6) (/64 3/6) Yes (J) Yes (J) Reverse Reinforement No Yes 2-point zigzg stith 9 J Oversting on medium weight or streth fris, tthing elsti, drning, et. 5.0 (3/6) (/6 /4).0 (/6) (/64 3/6) Yes (J) Reinforement Yes 3-point zigzg stith 0 J Oversting on medium weight or streth fris, tthing elsti, drning, et. 5.0 (3/6) (/6 /4).0 (/6) (/64 3/6) Yes (J) Reinforement No G Oversting on thin or medium weight fris 3.5 (/8) (3/32 3/6) 2.0 (/6) (/6 3/6) No Reinforement No 2 G Oversting on thik fris 5.0 (3/6) (3/32 3/6) 2.5 (3/32) (/6 3/6) No Reinforement No Oversting stith 3 4 G J Preventing frying in thik fris nd fris tht fry esily Oversting on streth fris 5.0 (3/6) 5.0 (3/6) (/8 3/6) (0 /4) 2.5 (3/32) 2.5 (3/32) (/6 3/6) (/32 3/6) No Reinforement No Yes (J) Reinforement No 5 J Oversting on thik or streth fris 5.0 (3/6) (0 /4) 2.5 (3/32) (/32 3/6) Yes (J) Reinforement No 6 J Oversting on streth fris nd deortive stithing 4.0 (3/6) (0 /4) 4.0 (3/6) (/6 3/6) Yes (J) Reinforement No 70

73 Stith Nme Pttern Presser Foot Applition Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul Twin Needle Reverse/ Reinforement Stithing Wlking Foot Blind hem stith 7 8 R R Blind hem stithing on medium weight fris Blind hem stithing on streth fris 00 (0) 00 (0) (/6) 2.0 (/6) (/6 /8) (/6 /8) No Reinforement No No Reinforement No Appliqué stith 9 J Appliqué stithing 3.5 (/8) (3/32 /4) 2.5 (3/32) (/6 3/6) Yes (J) Reinforement No Shell tuk stith 20 J Shell tuk stithing 4.0 (3/6) (0 /4) 2.5 (3/32) (/64 3/6) Yes (J) Reinforement No Pieing stright stith Stright stith tht looks hnd-sewn (for quilting) J J J Pieing stright stithing (with sem llowne of 6.5 mm (/4 inh) from the right edge of the presser foot) Pieing stright stithing (with sem llowne of 6.5 mm (/4 inh) from the left edge of the presser foot) Stright stith quilting tht looks hnd-sewn 5.5 (7/32).5 (/6) 0.0 (0) (0 /4) (0 /4) (0 /4) 2.0 (/6) 2.0 (/6) 2.5 (3/32) (/64 3/6) (/64 3/6) (/6 3/6) No Reinforement No No Reinforement Yes No Reinforement No 3 Zigzg stith (for quilting) 24 J Appliqué quilting, free-motion quilting, stin stithing 3.5 (/8) (0 /4).4 (/6) (0 3/6) No Reinforement Yes Appliqué stith (for quilting) 25 J Atthing ppliqués nd inding.5 (/6) (/32 /8).8 (/6) (/6 3/6) No Reinforement No Quilting stith (for stippling) 26 J Quilting kground stithing (stippling) 7.0 (/4) (/6 /4).6 (/6) (/6 3/6) No Reinforement No Stin sllop stith 27 N Sllop stithing 5.0 (3/6) (3/32 /4) 0.5 (/32) 0..0 (/64 /6) Yes (J) Reinforement No 28 J Pthwork stithing nd deortive stithing 4.0 (3/6) (0 /4).2 (/6) (/64 3/6) Yes (J) Reinforement No Joining stith 29 J Pthwork stithing, deortive stithing nd sewing oversting on oth piees of fri, suh s with triot 5.0 (3/6) (3/32 /4) 2.5 (3/32) (/6 3/6) Yes (J) Reinforement No 30 J Pthwork stithing nd deortive stithing 5.0 (3/6) (0 /4).2 (/6) (/64 3/6) Yes (J) Reinforement No Smoking stith 3 J Smoking stithing nd deortive stithing 5.0 (3/6) (0 /4).6 (/6) (/6 3/6) Yes (J) Reinforement No Fgoting stith J J Fgoting nd deortive stithing Fgoting nd deortive stithing 5.0 (3/6) 5.0 (3/6) (0 /4) (3/32 /4) 2.5 (3/32) 2.5 (3/32) (/6 3/6) (/6 3/6) Yes (J) Yes (J) Reinforement Reinforement No No Elsti-tthing stith 34 J Atthing elsti to streth fris 4.0 (3/6) (0 /4).0 (/6) (/64 3/6) Yes (J) Reinforement No Ldder stith 35 J Deortive stithing 4.0 (3/6) (0 /4) 3.0 (/8) (/6 3/6) No Reinforement No Rik-rk stith 36 J Deortive stithing 4.0 (3/6) (0 /4) 2.5 (3/32) (/6 3/6) Yes (J) Reinforement No Stith Setting Chrt 7

74 UTILITY STITCHES Stith Nme Pttern Presser Foot Applition Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul Twin Needle Reverse/ Reinforement Stithing Wlking Foot Deortive stith 37 J Deortive stithing 5.5 (7/32) (0 /4).6 (/6) (/6 3/6) Yes (J) Reinforement No Serpentine stith 38 N Deortive stithing nd elstitthing 5.0 (3/6) (/6 /4).0 (/6) (/64 3/6) Yes (J) Reinforement No 39 N Le sewing, deortive hemming, heirloom stithing, et. 3.5 (/8) (/6 /4) 2.5 (3/32) (/6 3/6) No Reinforement No 40 N Deortive hemming, heirloom stithing, et. 6.0 (5/64) (/6 /4) 3.0 (/8) (/6 3/6) No Reinforement No 4 N Deortive hemming on thin, medium weight nd plin weve fris, heirloom stithing, et. 5.0 (3/6) (/6 /4) 3.5 (/8) (/6 3/6) No Reinforement No 42 N Deortive hemming on thin, medium weight nd plin weve fris, heirloom stithing, et. 5.0 (3/6) (/6 /4) 4.0 (3/6) /6 3/6) Yes (J) Reinforement No Hemstithing 43 N Deortive hemming on thin, medium weight nd plin weve fris, heirloom stithing, et. 5.0 (3/6) (/6 /4) 2.5 (3/32) (/6 3/6) Yes (J) Reinforement No 44 N Deortive hemming on thin, medium weight nd plin weve fris, heirloom stithing, et. 5.0 (3/6) (/6 /4) 2.0 (/6) (/6 3/6) Yes (J) Reinforement No 45 N Deortive hemming, rion threding, heirloom stithing, et. 5.0 (3/6) (/6 /4) 3.0 (/8) (/6 3/6) Yes (J) Reinforement No 46 N Deortive stithing, smoking stithing, heirloom stithing, et. 6.0 (5/64) (/6 /4).6 (/6) (/6 3/6) No Reinforement No 47 N Deortive stithing, smoking stithing, heirloom stithing, et. 5.0 (3/6) (/6 /4).6 (/6) (/6 3/6) No Reinforement No 48 A Horizontl uttonholes on thin nd medium weight fris 5.0 (3/6) (/8 3/6) 0.4 (/64) (/64 /6) No Automti reinforement No 49 A Horizontl uttonholes on res tht re sujet to strin 5.0 (3/6) (/8 3/6) 0.4 (/64) (/64 /6) No Automti reinforement No 50 A Horizontl uttonholes on thik fris 5.0 (3/6) (/8 3/6) 0.4 (/64) (/64 /6) No Automti reinforement No Buttonhole stith 5 A Seured uttonholes for fris tht hve kings 5.0 (3/6) (/8 3/6) 0.4 (/64) (/64 /6) No Automti reinforement No 52 A Buttonholes for streth or knit fris 6.0 (5/54) (/8 5/64).0 (/6) (/32 /6) No Automti reinforement No 53 A Buttonholes for streth fris 6.0 (5/54) (/8 5/64).5 (/6) (/6 /8) No Automti reinforement No 54 A Bound uttonholes 5.0 (3/6) (0 5/64) 2.0 (/6) (/64 3/6) No Automti reinforement No 72

75 Stith Nme Pttern Presser Foot Applition Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul Twin Needle Reverse/ Reinforement Stithing Wlking Foot 55 A Keyhole uttonholes for thik or furry fris 7.0 (/4) (/8 /4) 0.5 (/32) (/64 /6) No Automti reinforement No Buttonhole stith 56 A Keyhole uttonholes for medium weight nd thik fris 7.0 (/4) (/8 /4) 0.5 (/32) (/64 /6) No Automti reinforement No 57 A Horizontl uttonholes for thik or furry fris 7.0 (/4) (/8 /4) 0.5 (/32) (/64 /6) No Automti reinforement No Drning stith Br tk stith A A A Drning medium weight fris Drning thik fris Reinforing openings nd res where the sem esily omes loose 7.0 (/4) 7.0 (/4) 2.0 (/6) (3/32 /4) (3/32 /4) (/6 /8) 2.0 (/6) 2.0 (/6) 0.4 (/64) (/64 3/32) (/64 3/32) (/64 /6) No No No Automti reinforement Automti reinforement Automti reinforement No No No 3 Button-sewing stith 6 M Button sewing 3.5 (/8) (3/32 3/6) No Automti reinforement No Eyelet stith 62 N Sewing eyelets, for exmple, on elts 7.0 (/4) 7.0, 6.0, 5.0 (/4, 5/64, 3/6) 7.0 (/4) 7.0, 6.0, 5.0 (/4, 5/64, 3/6) No Automti reinforement No 63 S Sewing stright stithes while utting the fri 0.0 (0) (0 3/32) 2.5 (3/32) (/64 3/6) No Reinforement No 64 S Sewing zigzg stithes while utting the fri 3.5 (/8) (/8 3/6).4 (/6) (0 3/6) No Reinforement No Side utter 65 S Oversting on thin nd medium weight fris while utting the fri 3.5 (/8) (/8 3/6) 2.0 (/6) (/6 3/6) No Reinforement No 66 S Oversting on thik fris while utting the fri 5.0 (3/6) (/8 3/6) 2.5 (3/32) (/6 3/6) No Reinforement No 67 S Oversting on medium weight nd thik fris while utting the fri 5.0 (3/6) (/8 3/6) 2.5 (3/32) (/6 3/6) No Reinforement No Horizontl stright stith N N Atthing ppliqués to sleeves (stright stith sewn to the left) Atthing ppliqués to sleeves (stright stith sewn to the right) No Reinforement No No Reinforement No Horizontl zigzg stith 70 7 N N Atthing ppliqués to sleeves (zigzg stith sewn to the left) Atthing ppliqués to sleeves (zigzg stith sewn to the right) No Reinforement No No Reinforement No Stith Setting Chrt 73

76 UTILITY STITCHES Other stithes Stith Type Pttern Presser Foot Twin Needle Pttern Size Adjustle Stithing Density Adjustle Pttern Length/width Left/Right Flipping Deortive stithes * 30* N No Lrge, Smll No Lrge: No Smll: Yes (*Not possile) Yes 3** Stin stithes * 8* N Yes (*Not possile) Lrge No Yes (*Not possile) Yes (*Not possile) * 7* 8* 9* 0* Crossstithes * 2* 3* 4* 5* N No Lrge No Yes (*Not possile) Yes Deortive stin stithes N No Lrge, Smll Yes Yes (length only) Yes Comined utility stithes N No Lrge No Yes Yes ** Pttern for mking djustment 74

77 Chrter stithes (Gothi font) Chrter stithes (Sript font) Left/Right Flipping 3 Adjustle Pttern Length/width 2 Adjustle Stithing Density N No Lrge, Smll No No Yes N No Lrge No No Yes Pttern Size Pttern Twin Needle Stith Type Presser Foot Stith Setting Chrt 75 3

78 UTILITY STITCHES Stith Type Pttern Presser Foot Twin Needle Pttern Size Adjustle Stithing Density Adjustle Pttern Length/width Left/Right Flipping Chrter stithes (Outline style) N No Lrge, Smll No No Yes

79 Seleting Stithing This setion provides detils on the vrious types of stithes ville nd the proedure for seleting stith. Stith types A stith n e seleted from the following types ville. For detils on the vrious stithes, refer to Stith Setting Chrt (pge 70). f i j h i j k Comined utility stithes (Cn e omined) You n sew with omintions from 39 utility stithes. Deortive stin stithes (Cn e omined) There re 0 deortive stin stithes. Cross stithes (Cn e omined) You n selet from 5 ross stithes. You n sew omintions of multiple deortive stithes. Ptterns sved in the mhine's memory You n retrieve sved pttern. (For detils, refer to Sving ptterns (pge 35).) 3 d e f g d e g h k Utility stithes You n selet from 7 utility stithes, inluding stright line stithing, oversting, utton holes nd si deortive stithes. If this is seleted, the utility stith seletion ppers right fter the power is turned on. My Custom Stith You n design originl stithes. (For detils, refer to Designing Pttern (My Custom Stith) (pge 39).) Chrter stithes Gothi font (Cn e omined) There re 97 hrters, inluding letters, symols nd numers, in the Gothi font. Chrter stithes Sript font (Cn e omined) There re 97 hrters, inluding letters, symols nd numers, in the Sript font. Chrter stithes Outline style (Cn e omined) There re 97 hrters, inluding letters, symols nd numers, in the outline style. Deortive stithes (Cn e omined) You n selet from 3 deortive stithes, inluding leves, flowers nd herts. You n sew omintions of multiple deortive stithes. Stin stithes (Cn e omined) You n selet from 8 stin stithes. You n sew omintions of multiple deortive stithes. Seleting stithing Turn on the sewing mhine. When n nimtion is displyed on the sreen, touh the sreen with your finger. The stright stith (left needle position) is shown seleted on the sreen. Press pnel. (Utility stith key) on the opertion The sreen ontining the vrious types of stithes ppers. Seleting Stithing 77

80 UTILITY STITCHES Selet the stith type. When deortive stith is seleted The sreen ontining the vrious stithes in the seleted stith type ppers. To selet different stith type, press (Bk key). Press the stith seletion. d (Previous pge key) displys the previous sreen, nd (Next pge key) displys the next sreen. e If neessry, speify the setting for utomti reverse/reinforement stithing nd djust the stith length, et. For detils on sewing with eh of the utility stithes, egin on pge 8. Note When stith is seleted, the ion for the presser foot tht should e used ppers on the sreen. Chek tht the orret presser foot is tthed efore strting to sew. If the wrong presser foot is instlled, turn off the sewing mhine, tth the orret presser foot, nd then selet the desired stith gin. Memo For detils on djusting the stith width nd length, refer to Adjusting the stith width (pge 58) nd Adjusting the stith length (pge 59). k j Seleting hrters Three styles of hrter stithes re ville. The proedure for seleting hrter is the sme with ll styles. Follow steps nd in Seleting stithing (pge 77) to disply the sreen where stith type n e seleted. Selet the hrter style. i h g d e f Deortive stith seletion Set width, length nd tension Lrge pttern size d Smll pttern size e Single stith sewing f Repet sewing g Horizontl mirror imge h Delete seleted pttern i Chek omined pttern j Automti thred utting k Automti reverse/reinforement stith To selet different stith, press remove the seleted pttern. to Selet the hrters. If wrong hrter ws seleted, press to erse the hrter, nd then selet the orret hrter. To selet different hrter style, press, nd then selet the new hrter style. Press to view smple of the seleted pttern. To enter spe, press _. 78

81 Exmple: Bus Sving stith settings This mhine is preset with the defult settings for the stith width (zigzg width), stith length, thred tension, progrmmed thred utting, nd utomti reverse/reinforement stithing for eh stith. However, if you wish to sve speifi settings for stith so tht they n e used lter, press fter hnging the settings to sve the new settings with the seleted stith. This feture n e used only with utility stithes. To use stith length of 2.0 mm for the stright stith Selet stright stith. Press. 3 Memo The defult stith length is 2.5 mm. Set the stith length to 2.0 mm. Press. d To reset the seleted stith pttern to its defult settings, press, nd then press. The onfirmtion messge is displyed. Seleting Stithing 79

82 UTILITY STITCHES Press. e Note The next time tht the sme stright stith is seleted, the stith length is set to 2.0 mm. All stith settings (stith width (zigzg width), stith length, thred tension, progrmmed thred utting, nd utomti reverse/reinforement stithing, et.) re sved, not just the setting tht ws hnged. When the sme stith pttern is seleted, the lst settings sved re displyed even if the mhine ws turned off. If the settings re hnged gin, or if is pressed to reset the setting to its defult, the new settings re not sved unless is pressed nother time. Even if is pressed, the settings for progrmmed thred utting nd utomti reverse/reinforement stithing nnot e reset. 80

83 Oversting Stithes Sew oversting stithes long the edges of ut fri to prevent fri from frying. 5 stithes re ville for oversting. The proedure for sewing oversting stith is explined ording to the presser foot tht is used. Sewing oversting stithes using oversting foot G Three stithes n e used to sew oversting with oversting foot G. Stith Nme Pttern Applition Oversting stith Preventing frying in medium weight nd thin fris Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul 3.5 (/8) Preventing frying in thik (3/6) fris nd fris tht fry 3 esily 5.0 (3/6) (3/32 3/6) (3/32 3/6) (/8 3/6) 2.0 (/6) 2.5 (3/32) 2.5 (3/32) (/6 3/6) (/6 3/6) (/6 3/6) Presser Foot G 3 Atth oversting foot G. G Position the fri with the edge of the fri ginst the guide of the presser foot, nd then lower the presser foot lever. For detils, refer to Repling the presser foot (pge 44). Selet stith. Guide d Sew with the edge of the fri ginst the presser foot guide. For detils, refer to Seleting stithing (pge 5). Needle drop point Oversting Stithes 8

84 UTILITY STITCHES Sewing oversting stithes using zigzg foot J Seven stithes n e used to sew oversting stithes with zigzg foot J. Stith Nme Pttern Applition Zigzg stith (enter needle position) Zigzg stith (right needle position) 2-point zigzg stith 3-point zigzg stith 7 Preventing frying (enter seline/reverse stithing) 8 Preventing frying (right seline/reinforement stithing) Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul 3.5 (/8) 3.5 (/8) Preventing frying in thik fris nd streth fris (3/6) 5.0 (3/6) (0 /4) (3/32 3/6) (/6 /4) (/6 /4).4 (/6).4 (/6).0 (/6).0 (/6) (0 3/6) (/64 3/6) (/64 3/6) (/64 3/6) Presser Foot J 4 Preventing frying in streth fris 5.0 (3/6) (0 /4) 2.5 (3/32) (/32 3/6) Oversting stith 5 Preventing frying in thik fris nd streth fris 5.0 (3/6) (0 /4) 2.5 (3/32) (/32 3/6) 6 Preventing frying in streth fris 4.0 (3/6) (0 /4) 4.0 (3/6) (/6 3/6) Atth zigzg foot J. J Sew long the edge of the fri with the needle dropping off the edge t the right. For detils, refer to Repling the presser foot (pge 44). Selet stith. Needle drop point Needle drop point For detils, refer to Seleting stithing (pge 5). 82

85 Sewing oversting stithes using the optionl side utter Using the side utter, sem llownes n e finished while the edge of the fri is ut off. Five stithes n e used to sew oversting stithes with the side utter. Note Thred the needle mnully when using the side utter, or only tth the side utter fter threding the needle using the needle threder. Stith Nme Pttern Applition 63 Sewing stright stithes while utting the fri Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul 0.0 (0) (0 3/32) 2.5 (3/32) (/64 3/6) Presser Foot 3 64 Sewing zigzg stithes while utting the fri 3.5 (/8) (/8 3/6).4 (/6) (0 3/6) Side Cutter 65 Preventing frying in thin nd medium weight fris while utting the fri 3.5 (/8) (/8 3/6) 2.0 (/6) ( /6 3/6) S 66 Preventing frying in thik fris while utting the fri 5.0 (3/6) (/8 3/6) 2.5 (3/32) ( /6 3/6) 67 Preventing frying in thik fris while utting the fri 5.0 (3/6) (/8 3/6) 2.5 (3/32) ( /6 3/6) Position the side utter so tht side utter pin is ligned with the noth in the presser foot holder, nd then slowly lower the presser foot lever. Remove the presser foot. For detils, refer to Repling the presser foot (pge 44). Hook the onneting fork of the side utter onto the needle lmp srew. Noth in presser foot holder Pin The side utter is tthed. Conneting fork Needle lmp srew Oversting Stithes 83

86 UTILITY STITCHES d e Rise the presser foot lever to hek tht the side utter is seurely tthed. Pss the upper thred under the side utter, nd then pull it out towrd the rer of the sewing mhine. Position the fri in the side utter. h The ut in the fri should e positioned over the guide plte of the side utter. Guide plte If the fri is not positioned orretly, the fri will not e ut. Selet stith. f i Lower the presser foot lever, nd then strt sewing. A sem llowne is ut while the stithing is sewn. For detils, refer to Seleting stithing (pge 5). If the stithing is sewn in stright line 63, the sem llowne will e out 5 mm (3/6 inh). g Mke ut of out 2 m (3/4 inh) long in the fri t the eginning of the stithing. 5 mm (3/6 inh) 2 m (3/4 inh) Memo The side utter n ut s muh s one lyer of 3-oz. denim. After using the side utter, len it y removing ny lint or dust. If the side utter n no longer ut fri, use rg to pply smll mount of oil to the utting edge of the utter. 84

87 Bsi Stithing Stright stithes re used for sewing plin sems. Five stithes re ville for si stithing. Stith Nme Pttern Applition Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul Presser Foot Bsting stith 6 Temporrily seuring 0.0 (0) (0 /4) 20 (3/4) 5 30 (3/6-3/6) Stright stith (left needle position) Stright stith (enter needle position) Bsi stithing nd sewing gthers or pintuks (left seline/ reverse stithing) 2 Bsi stithing nd sewing gthers or pintuks (left seline/ reinforement stithing) 3 Bsi stithing nd sewing gthers or pintuks (enter seline/reverse stithing) 0.0 (0) 0.0 (0) 3.5 (/8) (0 /4) (0 /4) (0 /4) 2.5 (3/32) 2.5 (3/32) 2.5 (3/32) (/64 3/6) (/64 3/6) (/64 3/6) J 3 Triple streth stith 4 Reinforing sems nd sewing streth fris 0.0 (0) (0 /4) 2.5 (3/32) (/6 3/6) Bsting Bsi stithing Sew sting with stith length etween 5 mm (3/6 inh) nd 30 mm (-3/6 inhes). Atth zigzg foot J. J Bste or pin together the fri piees. Atth zigzg foot J. J For detils, refer to Repling the presser foot (pge 44). Selet stith 6. For detils, refer to Repling the presser foot (pge 44). Selet stith. For detils, refer to Seleting stithing (pge 5). Strt sewing. For detils, refer to Strting to sew (pge 53). d For detils, refer to Seleting stithing (pge 5). Lower the needle into the fri t the eginning of the stithing. Bsi Stithing 85

88 UTILITY STITCHES e Lower the presser foot lever, nd then strt sewing. For detils, refer to Strting to sew (pge 53). For detils on sewing reverse/reinforement stithes, refer to Seuring the stithing (pge 55). Chnging the needle position The needle position used s the seline is different for the stright stith (left needle position) nd the stright stith (enter needle position). 2 When sewing is finished, ut the thred. f For detils, refer to Cutting the thred (pge 56). Stright stith (left needle position) Stright stith (enter needle position) When the stith width of the stright stith (left needle position) is set to its stndrd setting (0.0 mm), the distne from the needle position to the right side of the presser foot is 2 mm (/2 inh). If the stith width is hnged (etween 0 nd 7.0 mm (/4 inh)), the needle position will lso hnge. By hnging the stith width nd sewing with the right side of the presser foot ligned with the edge of the fri, sem llowne n e sewn with fixed width d e f Stith width setting Distne from the needle position to the right side of the presser foot 2.0 mm (/2 inh) 0.0 mm (3/8 inh) 6.5 mm (/4 inh) 5.0 mm (3/6 inh) For detils, refer to Adjusting the stith width (pge 58). 86

89 Blind Hem Stithing Seure the ottoms of skirts nd pnts with lind hem. Two stithes re ville for lind hem stithing. Stith Nme Pttern Applition Blind hem stith 7 Blind hem stithing on medium weight fris 8 Blind hem stithing on streth fris Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul 00 (0) 00 (0) (/6) 2.0 (/6) (/6 /8) (/6 /8) Presser Foot R Sew lind hem ording to the following proedure. Fold the fri long the desired edge of the hem, nd then ste it out 5 mm (3/6 inh) from the edge of the fri. Atth lind hem foot R. 3 For detils, refer to Repling the presser foot (pge 44). Selet stith. d d Wrong side of fri Bsting stithing Desired edge of hem 5 mm (3/6 inh) Fold k the fri long the sting, nd then position the fri with the wrong side fing up. 2 e For detils, refer to Seleting stithing (pge 5). Position the fri with the edge of the folded hem ginst the guide of the presser foot, nd then lower the presser foot lever. Wrong side of fri Bsting 2 3 Wrong side of fri Fold of hem Guide Blind Hem Stithing 87

90 UTILITY STITCHES f Adjust the stith width until the needle slightly thes the fold of the hem. If the needle does not th the hem fold The needle is too fr to the right. Press to inrese the stith width so tht the needle slightly thes the fold of the hem. Needle drop point When you hnge the needle drop point, rise the needle, nd then hnge the stith width. 2 Wrong side of fri Right side of fri For detils, refer to Adjusting the stith width (pge 58). Sew with the fold of the hem ginst the g presser foot guide. Stith width If the needle thes too muh of the hem fold The needle is too fr to the left. Press to derese the stith width so tht the needle slightly thes the fold of the hem. Remove the sting stithing. h 2 Wrong side of fri Right side of fri 2 Wrong side of fri Right side of fri 88

91 Buttonhole Stithing/Button Sewing Buttonholes n e sewn nd uttons n e sewn on. 0 stithes re ville for sewing one-step uttonholes nd one stith for sewing on uttons. Stith Nme Pttern Applition 48 Horizontl uttonholes on thin nd medium weight fris Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul 5.0 (3/6) (/8 3/6) 0.4 (/64) (/64 /6) Presser Foot 49 Horizontl uttonholes on res tht re sujet to strin 5.0 (3/6) (/8 3/6) 0.4 (/64) (/64 /6) 50 Horizontl uttonholes on thik fris 5 Buttonholes with r tks on oth ends for stilized fris 5.0 (3/6) 5.0 (3/6) (/8 3/6) (/8 3/6) 0.4 (/64) 0.4 (/64) (/64 /6) (/64 /6) 3 Buttonhole stith 52 Buttonholes for streth or knit fris 53 Buttonholes for streth fris 6.0 (5/64) 6.0 (5/64) (/8 5/64) (/8 5/64).0 (/6).5 (/6) (/32 /6) (/6 /8) A 54 Bound uttonholes 5.0 (3/6) (0 5/64) 2.0 (/6) (/64 3/6) 55 Keyhole uttonholes for thik or plush fris 7.0 (/4) (/8 /4) 0.5 (/32) (/64 /6) 56 Keyhole uttonholes for medium weight nd thik fris 7.0 (/4) (/8 /4) 0.5 (/32) (/64 /6) 57 Horizontl uttonhole for thik or plush fris 7.0 (/4) (/8 /4) 0.5 (/32) (/64 /6) Buttonsewing stith 6 Button sewing 3.5 (/8) (3/32 3/6) M Buttonhole Stithing/Button Sewing 89

92 UTILITY STITCHES Buttonhole sewing The mximum uttonhole length is out 28 mm (-/8 inhes) (dimeter + thikness of the utton). Buttonholes re sewn from the front of the presser foot to the k, s shown elow. Reinforement stithing The nmes of prts of uttonhole foot A, whih is used for sewing uttonholes, re indited elow. Use hlk to mrk on the fri the position nd length of the uttonhole Mrks on fri Button hole sewing A 4 Pull out the utton guide plte of uttonhole foot A, nd then insert the utton tht will e put through the uttonhole. d e Button guide plte Presser foot sle Pin Mrks on uttonhole foot 5 mm (3/6 inh) 90

93 If the utton does not fit in the utton guide plte Add together the dimeter nd thikness of the utton, nd then set the utton guide plte to the lulted length. (The distne etween the mrkings on the presser foot sle is 5 mm (3/6 inh).) Selet stith. d Presser foot sle Length of uttonhole (dimeter + thikness of utton) 5 mm (3/6 inh) Exmple: For utton with dimeter of 5 mm (9/6 inh) nd thikness of 0 mm (3/8 inh), the utton guide plte should e set to 25 mm ( inh) on the sle. e For detils, refer to Seleting stithing (pge 5). Position the fri with the front end of the uttonhole mrk ligned with the red mrks on the sides of the uttonhole foot, nd then lower the presser foot lever. 2 0 mm (3/8 inh) 5 mm (9/6 inh) The size of the uttonhole is set. Atth uttonhole foot A. For detils, refer to Repling the presser foot (pge 44). Mrk on fri (front) Red mrks on uttonhole foot A Pss the upper thred down through the hole in the presser foot. When lowering the presser foot, do not push in the front of the presser foot. Do not redue the gp. Buttonhole Stithing/Button Sewing 9

94 UTILITY STITCHES f Pull down the uttonhole lever s fr s possile. Press ( Thred Cutter utton) one. h The threds re ut, nd the needle is rised. Rise the presser foot, nd then remove the fri. Buttonhole lever The uttonhole lever is positioned ehind the rket on the uttonhole foot. Memo If the utomti thred utting setting ws seleted efore sewing, the mhine will utomtilly ut the threds t the end of the stithing. For detils, refer to Automtilly utting the thred (pge 62). When using the thred utter on the left side of the mhine or sissors to ut the threds, press ( Needle Position utton) to rise the needle, rise the presser foot, nd then pull out the fri efore utting the threds. For detils, refer to Using the thred utter (pge 57). 2 Buttonhole lever Brket i Rise the uttonhole lever to its originl position. g Gently hold the end of the upper thred in your left hnd, nd then strt sewing. j Insert pin long the inside of one r tk t the end of the uttonhole stithing to prevent the stithing from eing ut. One sewing is ompleted, the mhine utomtilly sews reinforement stithes, then stops. k Pin Use the sem ripper to ut towrds the pin nd open the uttonhole. Sem ripper For keyhole uttonholes, use the eyelet punh to mke hole in the rounded end of the uttonhole, nd then use the sem ripper to ut open the uttonhole. 92

95 Sewing uttonholes on streth fris When sewing uttonholes on streth fris, use gimp thred. Hook the gimp thred onto the prt of uttonhole foot A shown in the illustrtion. Eyelet punh When using the eyelet punh, ple thik pper or some other protetive sheet under the fri efore punhing the hole in the fri. CAUTION When opening the uttonhole with the sem ripper, do not ple your hnds in the utting diretion, otherwise injuries my result if the sem ripper slips. Do not use the sem ripper in ny other wy thn how it is intended. It fits into the grooves, nd then loosely tie it. 3 Chnging the density of the stithing Adjust the stith length. For detils, refer to Adjusting the stith length (pge 59). If the fri does not feed (for exmple, if it is too thik), derese the density of the stithing. Chnging the stith width Adjust the stith width. Atth uttonhole foot A. For detils, refer to Repling the presser foot (pge 44). Selet stith 52 or 53. d Adjust the stith width to the thikness of the e gimp thred. Lower the presser foot lever nd the f uttonhole lever, nd then strt sewing. When sewing is finished, gently pull the gimp g thred to remove ny slk. For detils, refer to Adjusting the stith width (pge 58). Memo Before sewing uttonholes, hek the stith length nd width y sewing tril uttonhole on srp piee of fri. Use hndsewing needle to pull the gimp h thred to the wrong side of the fri, nd then tie it. Buttonhole Stithing/Button Sewing 93

96 UTILITY STITCHES Button sewing Selet stith 6. d Buttons n e sewn on with the sewing mhine. Buttons with two or with four holes n e tthed. Mesure the distne etween the holes in the utton to e tthed. For detils, refer to Seleting stithing (pge 5). Rise the presser foot lever, nd then slide the drop feed lever, loted t the rer of the mhine on the se, to (to the left s seen from the rer of the mhine). e f Sine the end of the thred will e tied off lter, do not set the sewing mhine for progrmmed-thred utting. Adjust the stith width so tht it is the sme s the distne etween the holes in the utton. Ple the utton in the position where it will e sewn, nd lower the presser foot lever. Drop feed lever (s seen from the rer of the mhine) The feed dogs re lowered. Atth utton-sewing foot M. For detils, refer to Repling the presser foot (pge 44). Button The utton is held in ple. When tthing four-hole uttons, first sew the two holes losest to you. Then, slide the utton so tht the needle goes into the two holes towrd the rer of the sewing mhine, nd then sew them in the sme wy. 94

97 g Turn the hndwheel towrd you (ounterlokwise) to hek tht the needle orretly goes into the two holes of the utton. If it seems s if the needle will hit the utton, remesure the distne etween the holes in the utton. Adjust the stith width to the distne etween the utton holes. When you re finished tthing the utton, j slide the drop feed lever to (to the right s seen from the rer of the mhine) nd turn the hndwheel to rise the feed dogs. Memo The feed dog position swith is normlly set to the right side (s seen from the rer of mhine). The feed dogs ome up when you strt sewing gin. CAUTION When sewing, e sure tht the needle does not touh the utton, otherwise the needle my end or rek. Atthing shnk to utton To sew the utton with shnk, tth the utton with spe etween it nd the fri, nd then wind the thred y hnd. This tthes the utton seurely. Ple the utton into utton-sewing foot M, nd then pull the shnk lever towrd you. 3 Strt sewing. h Set the sewing speed ontroller to the left (so tht the speed will e slow). Shnk lever i The sewing mhine utomtilly stops fter sewing reinforement stithes. Do not press ( Thred Cutter utton). If dditionl strength is needed to seure the utton, perform the utton-sewing opertion twie. Use sissors to ut the upper thred nd the oin thred t the eginning of the stithing. Pull the upper thred t the end of the stithing to the wrong side of the fri, nd then tie it with the oin thred. After sewing is finished, ut the upper thred with plenty of exess, wind it round the thred etween the utton nd the fri, nd then tie it to the upper thred t the eginning of the stithing. Tie together the ends of the oin thred t the end nd t the eginning of the stithing on the wrong side of the fri. Cut off ny exess thred. Buttonhole Stithing/Button Sewing 95

98 UTILITY STITCHES Zipper Insertion A zipper n e sewn in ple. Stith Nme Pttern Applition Stright stith (enter needle position) 3 Atthing zippers Sewing oneled sems nd pintuks Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul 3.5 (/8) (0 /4) 2.5 (3/32) (/64 3/6) Presser Foot I There re mny methods for inserting zippers. The proedures for inserting entered zipper nd side zipper re desried elow. Using sting stith, ontinue sewing to the edge of the fri. Inserting entered zipper Stithing is sewn on oth piees of fri utted ginst eh other. 2 3 d Bsting stithing Reverse stithes Wrong side of fri End of zipper opening Right side of fri Stithing End of zipper opening d Press open the sem llowne from the wrong side of the fri. Atth zigzg foot J. Sew stright stithes up to the zipper opening. With the right sides of the fri fing eh other, sew reverse stithes fter rehing the zipper opening. For detils, refer to Bsi stithing (pge 85). Wrong side of fri 96

99 e Align the sem with the enter of the zipper, nd then ste the zipper in ple. Selet stith 3. h 2 f Wrong side of fri Bsting stithing Zipper Remove out 5 m (2 inhes) from the end of the sting on the outside For detils, refer to Seleting stithing (pge 5). CAUTION When using zipper foot I, e sure to selet the stright stith (enter needle position), nd slowly turn the hndwheel towrd you (ounterlokwise) to hek tht the needle does not touh the presser foot. If different stith is seleted or the needle hits the presser foot, the needle my end or rek. 3 g Wrong side of fri Zipper sting Outside sting d 5 m (2 inhes) Atth the presser foot holder to the right pin of zipper foot I. Topstith round the zipper. i 3 2 I 4 2 Pin on the right side Needle drop point For detils, refer to Repling the presser foot (pge 44). d Stithing Right side of fri Bsting stithing End of zipper opening CAUTION When sewing, e sure tht the needle does not touh the zipper, otherwise the needle my end or rek. Remove the sting stithing. j Zipper Insertion 97

100 UTILITY STITCHES Inserting side zipper d Press open the sem llowne from the wrong side of the fri. Stithing is visile on only one piee of fri. Use this type of zipper pplition for side openings nd k openings. 2 e Wrong side of fri Press the sem llowne so tht the right side (the side tht will not e stithed) hs n extr 3 mm (/8 inh). Stithing Right side of fri End of zipper opening The following proedure will desrie how to stith on the left side, s shown in the illustrtion. Atth zigzg foot J. Sew stright stithes up to the zipper opening. With the right sides of the fri fing eh other, sew reverse stithes fter rehing the zipper opening. 3 For detils, refer to Bsi stithing (pge 85). f 2 Wrong side of fri 3 mm (/8 inh) Align the zipper teeth with the pressed edge of the fri hving the extr 3 mm (/8 inh), nd then ste or pin the zipper in ple. Using sting stith, ontinue sewing to the edge of the fri. Zipper teeth Bsting stithing d Bsting stithing Reverse stithes Wrong side of fri End of zipper opening Atth the presser foot holder to the right pin g of zipper foot I. If the stithing will e sewn on the right side, tth the presser foot holder to the left pin of the zipper foot. I 2 Pin on the right side Needle drop point For detils, refer to Repling the presser foot (pge 44). 98

101 Selet stith 3. h j When you re out 5 m (2 inhes) from the end of the zipper, stop the sewing mhine with the needle lowered (in the fri), rise the presser foot lever. Open the zipper nd ontinue sewing. k For detils, refer to Seleting stithing (pge 5). CAUTION When using zipper foot I, e sure to selet the stright stith (enter needle position), nd slowly turn the hndwheel towrd you (ounterlokwise) to hek tht the needle does not touh the presser foot. If different stith is seleted or the needle hits the presser foot, the needle my end or rek. l Close the zipper, turn over the fri, nd then ste the other side of the zipper to the fri. 3 i Sew the zipper to the piee of fri with the extr 3 mm (/8 inh), strting from the se of the zipper. Bsting stithing m Atth the presser foot holder to the other pin of zipper foot I. If the presser foot holder ws tthed to the right pin in step g, hnge it to the left pin. CAUTION When sewing, e sure tht the needle does not touh the zipper, otherwise the needle my end or rek. 2 Pin on the left side Needle drop point I Zipper Insertion 99

102 UTILITY STITCHES n Topstith round the zipper. Sew reverse stithes t the end of the zipper opening nd lign the zipper teeth with the side of the presser foot d e Right side of fri End of zipper opening Reverse stithes Beginning of stithing Bsting stithing CAUTION When sewing, e sure tht the needle does not touh the zipper, otherwise the needle my end or rek. o When you re out 5 m (2 inhes) from the end of the zipper, stop the sewing mhine with the needle lowered (in the fri), rise the presser foot lever, nd then open the zipper nd ontinue sewing. Remove the sting stithing. p 00

103 Zipper/piping Insertion A zipper nd piping n e sewn in ple. Stith Nme Pttern Applition Stright stith (left needle position) Atthing zippers Sewing oneled sems nd piping Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul 0.0 (0) (0 /4) 2.5 (3/32) (/64 3/6) Presser Foot There re mny methods for inserting zippers nd pipings. The proedures for inserting entered zipper nd piping re desried elow, with the djustle zipper/piping foot. Inserting entered zipper Refer to step e of Inserting entered zipper (pge 96). d Loosen the positioning srew on the k of the presser foot. 3 Remove the presser foot nd presser foot holder (pge 46) to tth the srew-on djustle zipper/piping foot. Positioning srew e Slide the presser foot over either the left or right feed dog. Note Use srew driver to seurely tighten the srew tht holds the presser foot. If the srew is loose, the needle my rek nd use injures. Selet stith. Left sewing position Right sewing position f Chnge the needle position so tht the needle does not touh the presser foot. For detils, refer to Adjusting the stith width (pge 58). Needle drop point Zipper/piping Insertion 0

104 UTILITY STITCHES g CAUTION After djusting the needle position, slowly turn the hndwheel towrd you nd hek the needle does not touh (ounterlokwise) the presser foot. If the needle hits the presser foot, the needle my end or rek. Seurely tighten the positioning srew with srewdriver. Inserting piping Ple the piping etween two fri piees turned inside out, s shown elow. 3 2 Fri Piping Fri Positioning srew Refer to the steps of tthing the djustle zipper/piping foot on the previous pge. Sew long the piping. Topstith round the zipper. h 2 3 After sewing, turn fri piees. d 4 d Stithing Right side of fri Bsting stithing End of zipper opening CAUTION When sewing, e sure tht the needle does not touh the zipper, otherwise the needle my end or rek. Remove the sting stithing. i 02

105 Sewing Streth Fris nd Elsti Tpe Streth fris n e sewn nd elsti tpe n e tthed. Stith Nme Pttern Applition 5 Streth stith Streth fris Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul.0 (/6) (/6 /8) 2.5 (3/32) (/6 3/6) Presser Foot 2-point zigzg stith 3-point zigzg stith Elstitthing stith (3/6) Atthing elsti (3/6) 34 Atthing elsti to streth fris 4.0 (3/6) (/6 /4) (/6 /4) (0 /4).0 (/6).0 (/6).0 (/6) (/64 3/6) (/64 3/6) (/64 3/6) J 3 Oserve the orresponding preutions when performing eh of the following stithing opertions. Streth stithing Atth zigzg foot J. For detils, refer to Repling the presser foot (pge 44). Selet stith 5. J Elsti tthing When elsti tpe is tthed to the uff or wist of piee of lothing, the finished dimensions will e tht of the strethed elsti tpe. Therefore, it is neessry tht suitle length of the elsti tpe e used. Pin the elsti tpe to the wrong side of the fri. Pin the elsti tpe to the fri t few points to mke sure tht the tpe is uniformly positioned on the fri. For detils, refer to Seleting stithing (pge 5). Sew the fri without strething it. 2 Elsti tpe Pin Atth zigzg foot J. J For detils, refer to Repling the presser foot (pge 44). Sewing Streth Fris nd Elsti Tpe 03

106 UTILITY STITCHES Selet stith. Exmple: 2-point zigzg stith Exmple: Elsti-tthing stith For detils, refer to Seleting stithing (pge 5). d Sew the elsti tpe to the fri while strething the tpe so tht it is the sme length s the fri. While pulling the fri ehind the presser foot with your left hnd, pull the fri t the pin nerest the front of the presser foot with your right hnd. CAUTION When sewing, e sure tht the needle does not touh ny pins, otherwise the needle my end or rek. 04

107 Appliqué, Pthwork nd Quilt Stithing The stithes tht n e used for sewing ppliqués, pthwork nd quilts re desried elow. Stith Nme Pttern Applition Zigzg stith 7 Atthing ppliqués (enter seline/reverse stithing) 24 Appliqué quilting, free-motion quilting, stin stithing Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul 3.5 (/8) 3.5 (/8) (0 /4) (0 /4).4 (/6).4 (/6) (0 3/6) (0 3/6) Presser Foot Appliqué stith 9 25 Atthing ppliqués Atthing ppliqués nd inding 3.5 (/8).5 (/6) (3/32 /4) (/32 /8) 2.5 (3/32).8 (/6) (/6 3/6) (/6 3/6) 3 Pieing stright stith 2 22 Pieing stright stithing (with sem llowne of 6.5 mm (/4 inh) from the right edge of the presser foot) Pieing stright stithing (with sem llowne of 6.5 mm (/4 inh) from the left edge of the presser foot) 5.5 (7/32).5 (/6) (0 /4) (0 /4) 2.0 (/6) 2.0 (/6) (/64 3/6) (/64 3/6) J (3/6) (0 /4).2 (/6) (/64 3/6) Joining stith Pthwork stithing (3/6) (3/32 /4) 2.5 (3/32) (/6 3/6) (3/6) (0 /4).2 (/6) (/64 3/6) Mok hnd quilting stith 23 Stright stith quilting tht looks hnd quilting 0.0 (0) (0 /4) 2.5 (3/32) (/6 3/6) Quilting stippling 26 Stippling 7.0 (/4) (/6 /4).6 (/6) (/6 3/6) Memo Ptterns showing Q on the LCD re for quilting nd those showing P re for pieing. Appliqué, Pthwork nd Quilt Stithing 05

108 UTILITY STITCHES Appliqué stithing Selet stith. e For est results, use the inluded open toe foot. Cut out the ppliqué, leving sem llowne of etween 3 nd 5 mm (/8 nd 3/6 inh). For detils, refer to Seleting stithing (pge 5). Sem llowne Ple pttern mde of thik pper or stilizer on the k of the ppliqué, nd then fold over the sem llowne using n iron. f Turn the hndwheel towrd you (ounterlokwise), nd then egin sewing round the edge of the ppliqué, mking sure tht the needle drops just outside of the ppliqué. Turn the fri over, nd then ste or fuse it onto the fri tht it will e tthed to. When sewing round orners, stop the mhine with the needle in the fri just outside of the ppliqué, rise the presser foot lever, nd then turn the fri s needed to hnge the sewing diretion. Bsting stithing Atth the open toe foot. d 06 For detils, refer to Repling the presser foot (pge 44).

109 Pthwork (rzy quilt) stithing Fold the edge of the top piee of fri nd ple it over the lower piee. Sew the two piees of fri together so the pttern spns over oth piees. Pieing Sewing together two piees of fri is lled pieing. The fri piees should e ut with 7 mm (/4 inh) sem llowne. Sew pieing stright stith 7 mm (/4 inh) from either the right side or the left side of the presser foot. Bste or pin long the sem llowne of the fri tht you wish to piee together. Atth zigzg foot J. J 3 For detils, refer to Repling the presser foot (pge 44). Selet stith 2 or 22. d For detils, refer to Seleting stithing (pge 5). The pieing stright stith shows P on the LCD. Sew with the side of the presser foot ligned with the edge of the fri. For sem llowne on the right side Align the right side of the presser foot with the edge of the fri, nd sew using stith 2. 7 mm (/4 inh) Appliqué, Pthwork nd Quilt Stithing 07

110 UTILITY STITCHES For sem llowne on the left side Align the left side of the presser foot with the edge of the fri, nd sew using stith 22. When sewing with sem llowne, lign the left edge of the nrrow prt of the /4 inh quilting foot with the fri edge. 7 mm (/4 inh) Sem (3.2 mm (/8 inh)) Memo To hnge the width of the sem llowne (needle position), djust the stith width. For detils, refer to Adjusting the stith width (pge 58). Using the optionl /4 inh quilting foot If the /4 inh quilting foot is used, sems n e sewn with sem llowne of 6.4 mm (/4 inh). Strt sewing. e When the end of the stithing is rehed, stop f the sewing mhine. Sew until the mrk t the lower edge of the /4 inh quilting foot ligns with the lower edge of the fri. Bste or pin long the sem llowne of the fri tht you wish to piee together. Atth the /4 inh quilting foot mm (/4 inh) End of stithing Mrk on /4 inh quilting foot For detils, refer to Repling the presser foot (pge 44). Selet stith 3. Align the mrk t the upper edge of the /4 d inh quilting foot with the upper edge of the fri. Align the right edge of the fri with the right edge of the nrrow prt of the /4 inh quilting foot. 2 Mrk on /4 inh quilting foot Beginning of stithing 08

111 Quilting Sndwihing tting etween the top nd ottom lyers of fri is lled quilting. Quilts n esily e sewn using the optionl wlking foot nd the optionl quilting guide. Note Thred the needle mnully when using the wlking foot, or only tth the wlking foot fter threding the needle using the needle threder. When sewing with the wlking foot, sew t speed etween slow nd medium. When quilting, use 90/4 home sewing mhine needle. The wlking foot n only e used with stright or zigzg stith ptterns. Reverse stithes nnot e sewn with the wlking foot. Only selet stright or zigzg stith ptterns with reinforement stithes. For detils, refer to Stith Setting Chrt (pge 70). Bste the fri to e quilted. Remove the presser foot nd the presser foot holder. For detils, refer to Removing nd tthing the presser foot holder (pge 46). Hook the onneting fork of the wlking foot onto the needle lmp srew. d Lower the presser foot lever, insert the presser foot holder srew, nd then tighten the srew with the srewdriver. Presser foot holder srew The wlking foot is tthed. CAUTION Selet stith. e For detils, refer to Seleting stithing (pge 5). f Be sure to seurely tighten the srews with the srewdriver, otherwise the needle my touh the presser foot, using it to end or rek. Before strting to sew, slowly turn the hndwheel towrd you (ounterlokwise) nd hek tht the needle does not touh the presser foot. If the needle hits the presser foot, the needle my end or rek. Ple one hnd on eh side of the presser foot, nd hold fri tut while sewing. 3 Conneting fork Needle lmp srew Appliqué, Pthwork nd Quilt Stithing 09

112 UTILITY STITCHES Using the optionl quilting guide Use the quilting guide to sew prllel stithes tht re eqully sped. Free-motion quilting With free-motion quilting, lower the feed dogs (using the drop feed lever) so tht the fri n e moved freely in ny diretion. When free-motion quilting, use the following instrutions with the optionl quilting foot. Insert the stem of the quilting guide into the hole t the rer of the wlking foot or presser foot holder. Wlking foot Presser foot holder Adjust the stem of the quilting guide so tht the guide ligns with the sem tht hs lredy een sewn. Note Thred the needle mnully when using the quilting foot, or only tth the quilting foot fter threding the needle using the needle threder. Remove the presser foot nd the presser foot holder. Refer to Removing nd tthing the presser foot holder (pge 46). Seure the quilting foot with the presser foot holder srew. The pin on the quilting foot should e positioned over the needle lmp srew. 2 3 Note The optionl quilting guide is ville through rother deler. Pin on quilting foot Presser foot holder srew Needle lmp srew Hold the quilting foot in ple with your right hnd, nd then tighten the presser foot holder srew using the srewdriver in your left hnd. Presser foot holder srew 0

113 CAUTION Be sure to seurely tighten the srews with the srewdriver, otherwise the needle my touh the presser foot, using it to end or rek. Slide the drop feed lever, loted t the rer of d the mhine on the se, to (to the left s seen from the rer of the mhine). e f Feed dog position swith (s seen from the rer of the mhine) The feed dogs re lowered. Turn on the sewing mhine, nd then selet stith. For detils, refer to Seleting stithing (pge 5). Use oth hnds to hold the fri tut, nd then move the fri to follow the pttern. Reinforement stithes re sewn t the eginning nd end of sewing. Stin stithing using the sewing speed ontroller A deortive stith n e sewn y hnging the stith width of stin stith. If the sewing mhine is set so tht the stith width n e djusted using the sewing speed ontroller, the stith width n quikly nd esily e djusted. In this se, the sewing speed is djusted with the foot ontroller. Connet the foot ontroller. For detils, refer to Strting to sew (pge 53). Atth zigzg foot J. J For detils, refer to Repling the presser foot (pge 44). Turn on the sewing mhine, nd then press (Settings key) on the opertion pnel. 3 The settings sreen ppers. Press ON for stith width ontrol setting. d Pttern After sewing is finished, slide the drop feed g lever to (to the right s seen from the rer of the mhine) nd turn the hndwheel to rise the feed dogs. Normlly, the drop feed lever is positioned t the right. The mhine is now set so tht the stith width n e ontrolled with the sewing speed ontroller. If the stith width ontrol setting is set to ON, for stith width will hnge to sewing speed ontroller ion. Appliqué, Pthwork nd Quilt Stithing

114 UTILITY STITCHES Press e (Bk key). When you re finished sewing, set the stith h width ontrol setting k to OFF. Memo Although the stithing result differs depending on the type of fri eing sewn nd the thikness of the thred eing used, for est results, djust the stith length to etween 0.3 nd 0.5 mm (/64 nd /32 inh). The initil sreen ppers gin. Selet stith 24. f g For detils, refer to Seleting stithing (pge 5). While sewing, slide the sewing speed ontroller to djust the stith width. Slide the ontroller to the left to mke the width nrrower. Slide the ontroller to the right to mke the width wider. Nrrower Wider Adjust the sewing speed with the foot ontroller. Memo When the foot ontroller is plugged in, ( Strt/Stop utton) nnot e used to strt sewing. 2

115 Reinforement Stithing Reinfore points tht will e sujet to strin, suh s sleeve holes, insems nd poket orners. Stith Nme Pttern Applition Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul Presser Foot Triple streth stith 4 Reinforing the sems of sleeves nd insems 0.0 (0) (0 /4) 2.5 (3/32) (/6 3/6) J Br tk stith 60 Reinforing the ends of openings, suh s the orners of pokets 2.0 (/6) (/6 /8) 0.4 (/64) (/64 /6) Drning stith Drning medium weight fris Drning thik fris 7.0 (/4) 7.0 (/4) (3/32 /4) (3/32 /4) 2.0 (/6) 2.0 (/6) (/64 3/32) (/64 3/32) A 3 Triple streth stithing Br tk stithing Use triple streth stithing to reinfore sleeve holes nd insems. Atth zigzg foot J. Br tks re used to reinfore points sujet to strin, suh s poket orners nd openings. As n exmple, the proedure for sewing r tks t poket orners is desried elow. J For detils, refer to Repling the presser foot (pge 44). Selet stith 4. Determine the desired length of the r tk. Set the utton guide plte on uttonhole foot A to the desired length. (The distne etween the mrkings on the presser foot sle is 5 mm (3/6 inh).) For detils, refer to Seleting stithing (pge 5). 2 3 Strt sewing. For detils, refer to Strting to sew (pge 53). Presser foot sle Length of r tk 5 mm (3/6 inh) A r tk with mximum length of out 28 mm ( /8 inhes) n e sewn. Reinforement Stithing 3

116 UTILITY STITCHES Atth uttonhole foot A. For detils, refer to Repling the presser foot (pge 44). e Pull down the uttonhole lever s fr s possile. Selet stith 60. d For detils, refer to Seleting stithing (pge 5). Position the fri so tht the opening of the poket fes towrd you, nd then lower the presser foot lever so tht the needle drops 2 mm (/6 inh) in front of the poket opening. Buttonhole lever The uttonhole lever is positioned ehind the rket on the uttonhole foot. 2 Buttonhole lever Brket f Gently hold the end of the upper thred in your left hnd, nd then strt sewing. 2 mm (/6 inh) Pss the upper thred down through the hole in the presser foot. When lowering the presser foot, do not push in the front of the presser foot, otherwise the r tk will not e sewn with the orret size. One sewing is ompleted, the mhine utomtilly sews reinforement stithes, then stops. Rise the presser foot lever, remove the fri, g nd then ut the threds. Rise the uttonhole lever to its originl h position. Do not redue the gp. Memo If the fri does not feed, for exmple, euse it is too thik, inrese the stith length. For detils, refer to Adjusting the stith length (pge 59). 4

117 Drning Fri tht hs een torn n e drned. Drning is sewn s shown elow. 3 Reinforement stithing Determine the desired length of the drning. Set the utton guide plte on uttonhole foot A to the desired length. (The distne etween the mrkings on the presser foot sle is 5 mm (3/6 inh).) Selet stith 58 or d For detils, refer to Seleting stithing (pge 5). Position the fri so tht the needle is 2 mm (/6 inh) in front of the re to e drned, nd then lower the presser foot lever. Presser foot sle Length of drning 5 mm (3/6 inh) d 7 mm (/4 inh) Atth uttonhole foot A. For detils, refer to Repling the presser foot (pge 44). 2 Ter 2 mm (/6 inh) Reinforement Stithing 5

118 UTILITY STITCHES Pss the upper thred down through the hole in the presser foot. When lowering the presser foot, do not push in the front of the presser foot, otherwise the drning will not e sewn with the orret size. Rise the presser foot lever, remove the fri, g nd then ut the threds. Rise the uttonhole lever to its originl h position. Memo If the fri does not feed, for exmple, euse it is too thik, inrese the stith length. For detils, refer to Adjusting the stith length (pge 59). Do not redue the gp. e Pull down the uttonhole lever s fr s possile. Buttonhole lever The uttonhole lever is positioned ehind the rket on the uttonhole foot. 2 Buttonhole lever Brket f Gently hold the end of the upper thred in your left hnd, nd then strt sewing. One sewing is ompleted, the mhine utomtilly sews reinforement stithes, then stops. 6

119 Eyelet Stithing Eyelets, suh s those on elts, n e sewn. Three sizes of eyelets re possile: 7 mm, 6 mm nd 5 mm (/4, 5/64 nd 3/6 inh). Stith Nme Pttern Applition Eyelet stith 62 Sewing eyelets, for exmple, on elts Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul 7.0 (/4) 7.0, 6.0 or 5.0 (/4, 5/64 or 3/6) 7.0 (/4) 7.0, 6.0 or 5.0 (/4, 5/64 or 3/6) Presser Foot N Atth monogrmming foot N. d Lower the needle into the fri t the eginning of the stithing, nd then lower the presser foot lever. 3 For detils, refer to Repling the presser foot (pge 44). Selet stith 62. For detils, refer to Seleting stithing (pge 5). Adjust either the stith width or the stith length to selet the desired eyelet size. Strt sewing. e One sewing is ompleted, the mhine utomtilly sews reinforement stithes, then stops. f Use the eyelet punh to ut hole in the enter of the eyelet mm 6mm 5mm For detils, refer to Adjusting the stith width (pge 58) nd Adjusting the stith length (pge 59). When using the eyelet punh, ple thik pper or some other protetive sheet under the fri efore punhing the hole in the fri. Memo If light weight thred is used, the stithing my e sprse. If this ours, sew the eyelet twie efore removing the fri, one on top of the other. Eyelet Stithing 7

120 UTILITY STITCHES Horizontl Stithing Horizontl stithing is used to tth ppliqués to fri tht nnot e moved round, suh s ylindril piees. Stright stithes nd zigzg stithes tht sew to either the left or right re ville. Stith Nme Pttern Applition Horizontl stright stith Horizontl zigzg stith 68 Atthing ppliqués to sleeves (stright stith sewn to the left) 69 Atthing ppliqués to sleeves (stright stith sewn to the right) 70 Atthing ppliqués to sleeves (zigzg stith sewn to the left) 7 Atthing ppliqués to sleeves (zigzg stith sewn to the right) Stith Width [mm (inh)] Stith Length [mm (inh)] Presser Foot N The illustrtion elow shows the sewing order for the following explntion. 4 d Lower the needle into the fri t the eginning of the stithing, nd then strt sewing. Lower the needle t the upper-right orner. 3 2 Remove the flt ed tthment. For detils, refer to Free-rm sewing (pge 47). Atth monogrmming foot N. For detils, refer to Repling the Presser Foot (pge 44). e The fri is fed towrd the k of the mhine, s usul. After you hve sewn to the orner, stop the sewing mhine, nd then selet stith 68. Strt sewing. f Selet stith. For detils, refer to Seleting stithing (pge 5). The fri is fed to the right. After you hve sewn to the orner, stop the g sewing mhine, nd then selet stith. 8

121 Press ( Reverse/Reinforement Stith h utton). Hold ( Reverse/Reinforement Stith utton) pressed until the stithing rehes the upper-left orner. The fri is fed forwrd. i After you hve sewn to the orner, stop the sewing mhine, nd then selet stith 69. Strt sewing. j 3 k l The fri is fed to the left. After you hve sewn to the orner, stop the sewing mhine, nd then selet stith gin. After sewing 3 to 5 stithes t the eginning of the stithing, stop the sewing mhine. Memo The feeding diretion of the fri differs depending on the stith tht is seleted. Be sure to guide the fri while it is sewn. Horizontl Stithing 9

122 UTILITY STITCHES Deortive Stithing The utility stithes ontin the following deortive stithes. Stith Nme Pttern Applition Fgoting stith Sewing two piees of fri together ross n open sem (3/6) 5.0 (3/6) Stith Width [mm (inh)] Stith Length [mm (inh)] Auto Mnul Auto Mnul (0 /4) (3/25 /4) 2.5 (3/32) 2.5 (3/32) (/6 3/6) (/6 3/6) Presser Foot (3/6) (0 /4).2 (/6) (/64 3/6) Joining stith Deortive ridging stithes (3/6) (3/32 /4) 2.5 (3/32) (/6 3/6) (3/6) (0 /4).2 (/6) (/64 3/6) J Shell tuk stith 20 Shell tuk stithing on ollrs nd urves 4.0 (3/6) (0 /4) 2.5 (3/32) (/64 3/6) (3/6) (0 /4).6 (/6) (/6 3/6) Smoking stith 32 Smoking fris to dd texture 5.0 nd elstiity (3/6) (0 /4) 2.5 (3/32) (/6 3/6) (3/6) (3/32 /4) 2.5 (3/32) (/6 3/6) Sllop stith 27 Stin sllop stithing 5.0 (3/6) (3/32 /4) 0.5 (/32) 0..0 (/64 /6) Le sewing, deortive (/8) 40 hemming, heirloom stithing, et. 6.0 (5/64) (/6 /4) (/6 /4) 2.5 (3/32) 3.0 (/8) (/6 3/6) (/6 3/6) Hemstithing (3/6) Deortive hemming nd (3/6) heirloom stithing, et. on thin, 43 medium weight nd plin weve 5.0 fris (3/6) (/6 /4) (/6 /4) (/6 /4) 3.5 (/8) 4.0 (3/6) 2.5 (3/32) (/6 3/6) (/6 3/6) (/6 3/6) N (3/6) (/6 /4) 2.0 (/6) (/6 3/6) 45 Deortive hemming, rion threding, heirloom stithing, et. 5.0 (3/6) (/6 /4) 3.0 (/8) (/6 3/6) 20

123 Stith Nme Pttern Applition Hemstithing (5/64) Heirloom stithing, et (3/6) Stith Width [mm (inh)] (/6 /4) (/6 /4).6 (/6).6 (/6) Stith Length [mm (inh)] Auto Mnul Auto Mnul (/6 3/6) (/6 3/6) Presser Foot N Ldder stith (3/6) (0 /4) 3.0 (/8) (/6 3/6) Rik-rk stith Deortive stith Serpentine stith (3/6) Deortive stithing (7/32) (3/6) (0 /4) (0 /4) (/6 /4) 2.5 (3/32).6 (/6).0 (/6) (/6 3/6) (/6 3/6) (/64 3/6) J N 3 Fgoting Selet stith 32 or 33. d Stithing ross n open sem is lled fgoting. It is used on louses nd hildren's lothing. This stith is more deortive when thiker thred is used. Use n iron to fold the two piees of fri long their sems. Bste the two piees of fri, seprted y out 4 mm (3/6 inh), onto thin pper or sheet of wter-solule stilizer. If you drw line down the middle of the thin pper or wter-solule stilizer, sewing is esier. 3 For detils, refer to Seleting stithing (pge 5). Set the stith width to 7.0 mm (/4 inh). e For detils, refer to Adjusting the stith width (pge 58). f Sew with the enter of the presser foot ligned long the enter of the two piees of fri. 2 Thin pper or wter solule stilizer Bsting stithing 4 mm (3/6 inh) Atth zigzg foot J. J For detils, refer to Repling the presser foot (pge 44). After sewing is finished, remove the pper. g Deortive Stithing 2

124 UTILITY STITCHES Sllop stithing The wve-shped repeting pttern tht looks like shells is lled slloping. It is used on the ollrs of louses nd to deorte the edges of projets. Atth monogrmming foot N. Smoking The deortive stith reted y stithing or emroidering over gthers is lled smoking. It is used to deorte the front of louses or uffs. The smoking stith dds texture nd elstiity to fri. Atth zigzg foot J. J For detils, refer to Repling the presser foot (pge 44). Selet stith 27. For detils, refer to Seleting stithing (pge 5). Stith long the edge of the fri, mking sure not to sew diretly on the edge of the fri. For detils, refer to Repling the presser foot (pge 44). Selet the stright stith, nd then djust the stith length to 4.0 mm (3/6 inh) nd loosen the thred tension. For detils, refer to Adjusting the stith length (pge 59) nd Adjusting the thred tension (pge 59). Pull up the oin thred. For detils, refer to Pulling up the oin thred (pge 39). Sew prllel stithing t intervls of m (3/8 inh). For etter results, pply spry strh the fri nd press with hot iron efore it is sewn. Trim long the stithes. d d m (3/8 inh) Do not use reverse/reinforement stithing or thred utting. At the end of the stithing, the thred is pulled out out 5 m (2 inhes). Pull the oin threds to rete gthers. Smooth the gthers y ironing them. Be reful not to ut the stithes. 22

125 Selet stith 3, 32 or 33. e Shell tuk stithing The gthers tht look like shells re lled shell tuks. They re used to deorte trims, the front of louses or uffs mde of thin fris. For detils, refer to Seleting stithing (pge 5). Fold the fri long the is. Stith etween the stright stithes. f Atth zigzg foot J. 3 J Pull out the threds for the stright stithes. g For detils, refer to Repling the presser foot (pge 44). Selet stith 20 tension., nd then inrese the thred For detils, refer to Seleting stithing (pge 5) nd Adjusting the thred tension (pge 59). Deortive Stithing 23

126 UTILITY STITCHES d Sew while mking sure tht the needle drops slightly off the edge of the fri. Joining Deortive ridging stithes n e sewn over the sem llowne of joined fris. This is used when mking rzy quilt. Atth zigzg foot J. Needle drop point J For detils, refer to Repling the presser foot (pge 44). Sew together the right sides of the two piees of fri, nd then open up the sem llownes. 2 e Unfold the fri, nd then iron the tuks down to one side. 3 Wrong side of fri 7 mm (/4 inh) sem llowne Stright stith Selet stith 28, 29 or 30. d For detils, refer to Seleting stithing (pge 5). Turn the fri over so tht the right side fes up, nd then sew over the sem with the enter of the presser foot ligned with the sem. Right side of fri 24

127 Heirloom stithing When sewing with the wing needle, the needle holes re enlrged, reting le-like deortive stith. This is used to deorte hems nd tleloths on thin or medium weight fris in ddition to plin weve fris. Selet stith. The stithes tht n e used re 39, 40, 4, 42, 43, 44, 45, 46 or 47. Note If the thred eomes tngled, use stilizer mteril. Instll the wing needle. 3 Use 30/705H 00/6 wing needle. For detils on instlling needle, refer to Repling the needle (pge 42). The needle threder nnot e used with the wing needle, otherwise the sewing mhine my e dmged. Mnully pss the thred through the eye of the needle from the front to the k. For detils, refer to Threding the needle mnully (without using the needle threder) (pge 35). Atth monogrmming foot N. For detils, refer to Repling the presser foot (pge 44). For detils, refer to Seleting stithing (pge 5). When sewing with the wing needle, selet stith width of 6.0 mm (5/64 inh) or less. Strt sewing. d CAUTION When sewing with the wing needle, selet stith width of 6.0 mm (5/64 inh) or less, otherwise the needle my end or rek. After djusting the stith width, slowly turn the hndwheel towrd you (ounterlokwise) nd hek tht the needle does not touh the presser foot. If the needle hits the presser foot, the needle my end or rek. Deortive Stithing 25

128 UTILITY STITCHES Prtilly removing threds is lled drwnwork. This gives eutiful result with fris tht hve loose weve. Two wys to rete drwnwork re desried elow. Drwnwork (Exmple ) Press on the LCD. e The pttern displyed t the top of the sreen is mirrored. Sew long the other edge of the fryed setion f so tht it looks like the previous stithing. Pull out severl threds from the fri. N Atth monogrmming foot N. Press, nd set the horizontl mirror g imge key k to OFF. For detils, refer to Repling the presser foot (pge 44). Selet stith 39. For detils, refer to Seleting stithing (pge 5). With the right side of the fri fing up, sew d long the right edge of the fryed setion. N 26

129 Drwnwork (Exmple 2) Pull out severl threds from two setions of the fri, seprted y n unfryed setion of out 4 mm (3/6 inh). 3 4 mm (3/6 inh) Atth monogrmming foot N. For detils, refer to Repling the presser foot (pge 44). Selet stith 42. For detils, refer to Seleting stithing (pge 5). Sew long the enter of the unfryed setion. d N Deortive Stithing 27

130 UTILITY STITCHES Sewing the Vrious Built-in Deortive Ptterns You n sew deortive stithes, stin stithes, ross stithes, deortive stin stithes, omined utility stithes nd 3 types of hrter stithes. All re sewn with monogrmming foot N. Sewing eutiful ptterns In order to sew the ptterns orretly, the following must e onsidered. Fri Before sewing streth or thin fris or fris with orse weve, ffix stilizer mteril to the wrong side of the fri or ple thin sheet of pper, suh s tring pper, under the fri. Sine mteril pukering or unhed stithes my our when stin stithes re sewn, e sure to ffix stilizer mteril to the fri. Needles nd threds When sewing thin, medium weight or streth fris, use the ll point needle. When sewing thik fris, use 90/4 home sewing mhine needle. In ddition, #50 to #60 thred should e used. Tril sewing Depending on the type nd thikness of the fri eing sewn nd whether or not stilizer mteril is used, the desired result my not e hieved. Be sure to sew tril piee of fri efore sewing your projet. In ddition, while sewing, e sure to guide the fri with your hnds in order to prevent the fri from slipping. Sewing ptterns Atth monogrmming foot N. For detils, refer to Repling the presser foot (pge 44). Selet stith. For detils, refer to steps through e of Seleting stithing (pge 77). Strt sewing. d The stithing is sewn in the diretion indited y the rrow. Sew reinforement stithes. When sewing with hrter stith, reinforement stithes re utomtilly sewn fter eh hrter. When sewing pttern with stith other thn hrter stith, it is useful to first set the utomti reverse/reinforement stithing setting. For detils, refer to Automtilly sewing reverse/reinforement stithes (pge 6). e When you re finished sewing, use sissors to trim off ny exess threds t the eginning of the stithing nd etween the ptterns. Memo For detils on djusting the stith width nd length, refer to Adjusting the stith width (pge 58) nd Adjusting the stith length (pge 59). 28

131 Chnging the pttern size The size of hrter stithes in the Gothi font nd outline style, deortive stithes, nd deortive stin stithes n e swithed etween lrge nd smll. However, the size of other ptterns nnot e hnged. Chnging the stith density If deortive stin stith hs een seleted, the stith density n e hnged. Press (Utility stith key) on the opertion pnel, nd selet (Deortive stin stith). Selet stith. For detils on seleting stith, refer to Seleting stithing (pge 77). Press until the desired size is seleted. 3 Selet deortive stin stith pttern. Repet steps nd. Press until the desired stith density is seleted. Selet for sprse stithing, or selet for ompt stithing. Memo The lrge pttern size is the defult. If the smll pttern size is seleted, smll ptterns n e omined nd onneted. If multiple ptterns hve een omined, the size of eh seleted pttern n e speified. CAUTION If the stithing density is too ompted, depending on the needle, the stithes my e unhed together, using the needle to rek. Sewing the Vrious Built-in Deortive Ptterns 29

132 UTILITY STITCHES Chnging the length for stin stithes Press. The length for one stin stith n e hnged in five grdtions. Press (Utility stith key) on the opertion pnel, nd selet (Stin stith). It turns to nd the pttern is longer. Selet stin stith pttern. Eh time you press it the numer hnges. You n selet from -. 30

133 Shifting ptterns Stin stithes n e shifted to the left or right y hlf the width of the pttern, llowing you to rete stepshped pttern. This is lled step pttern. Selet one to move the stith pttern to the left y hlf the width of the stith pttern. Selet one to move the stith pttern to the right y hlf the width of the stith pttern. As n exmple, the proedure for reting the following pttern is desried elow. Press. Press (Utility stith key) on the opertion pnel, nd selet (Stin stith). 3 The next pttern seleted is moved hlf width to the right. Selet stin stith pttern. Selet the sme pttern. d Sewing the Vrious Built-in Deortive Ptterns 3

134 UTILITY STITCHES Press. e Comining ptterns You n sew with omintions of stithes from hrter stithes, deortive stithes, stin stithes, omined utility stithes, deortive stin stithes nd ross stithes. Touh (Utility stith key) on the opertion pnel, nd selet the stith type. The next pttern seleted is moved hlf width to the left. Selet the first pttern. The first pttern is seleted nd ppers in on the sreen. f Speify tht the ptterns will e sewn repetedly. When the sewing is strted, the seleted pttern is sewn repetedly until the sewing mhine is stopped. For detils, refer to Repeting ptterns (pge 33). Exmples of step ptterns 32

135 Selet the next pttern. The omined pttern ppers on the sreen. Repeting ptterns When multiple stithes re omined, the sewing mhine stops when the pttern displyed on the sreen hs een ompleted. Use the following opertions to sew omined pttern repetedly. After the ptterns hve een omined, press. If pressed gin, it turns to (single sewing). d To remove seleted pttern, press on the sreen. The pttern tht ws seleted lst is removed. To omine ptterns from different types, press (Bk key), nd fter seleting the type, selet the next pttern. After ll of the desired ptterns re seleted, strt sewing. turns to, nd you n now sew the speified pttern repetedly. 2 3 The order tht the ptterns pper on the sreen is the order tht they will e sewn. Single Repeted Memo Up to 70 ptterns n e omined. If multiple ptterns hve een omined, the sewing mhine stops one ll the seleted ptterns displyed in the LCD hve een sewn. To repetedly sew the omined pttern, refer to Repeting ptterns. The omined pttern n e sved for lter use. For detils, refer to Sving ptterns (pge 35). Note If repeted sewing is set, the pttern is repetedly sewn until the sewing mhine is stopped. If the sewing mhine is turned off, the repeted/single sewing setting returns to its defult setting. Sewing the Vrious Built-in Deortive Ptterns 33

136 UTILITY STITCHES Mirroring pttern imge After single pttern hs een seleted, press to mirror the pttern imge horizontlly. Cheking the pttern When the speified pttern is not displyed on the sreen, hek the pttern using the following steps. Press. The sreen for heking the pttern is displyed. Press, nd onfirm the pttern. Press (Bk key). The initil sreen ppers gin. Memo The omined pttern n e sved for lter use. For detils, refer to Sving ptterns (pge 35). 34

137 Sving ptterns Comined ptterns n e sved for lter use. Sine sved ptterns re not lost fter the sewing mhine is turned off, they n e retrieved t ny time. Up to 0 ptterns n e sved. Sving pttern Retrieving pttern Press. Retrieve the sved pttern. Crete the omined pttern tht you wish to sve. For detils, refer to Comining ptterns (pge 32). Press pnel. (Memory key) on the opertion The sreen for seleting poket ppers. Selet the poket where the omined pttern you wish to retrieve is stored. indites pokets where ptterns re lredy sved. 3 Sving... ppers while the pttern is eing sved. After the pttern is sved, the initil sreen ppers gin. Do not turn off the sewing mhine while the pttern is eing sved, otherwise the pttern dt my e lost. The seleted poket is shown in reverse highlighting, nd the sved pttern is displyed. Chek the ontents, nd then press. Press to hek pttern tht is not displyed ompletely. The sved pttern is retrieved. The pttern seletion sreen ppers, nd you n sew the pttern you hve retrieved. Sewing the Vrious Built-in Deortive Ptterns 35

138 UTILITY STITCHES Deleting sved pttern Sved pttern in the pokets n e deleted. Press. Religning the pttern The pttern my not e sewn orretly, depending on the type of fri eing sewn or the sewing speed. If this ours, djust the pttern while sewing on piee of srp fri tht is the sme s tht used for your projet. Atth monogrmming foot N. Selet the poket where the pttern you wish to delete is stored. indites pokets where ptterns re lredy sved. For detils, refer to Repling the presser foot (pge 44). Press (Utility stith key) on the opertion pnel, nd selet (Deortive stith). The seleted poket is shown in reverse highlighting, nd the sved pttern is displyed. Chek the ontents, then press. The sreen ontining the vrious deortive stithes ppers. Selet. The onfirmtion messge is displyed. Press. d The sved pttern nd the poket re deleted. The pttern lignment stith is seleted. 36

139 Strt sewing. d Press f (Settings key) on the opertion pnel. e The pttern for mking the djustment is sewn. The sewing mhine stops fter it hs finished sewing the pttern. Chek the sewn pttern. If the prt of the pttern indited in the illustrtion is sewn uniformly, the pttern is orretly ligned. The settings sreen ppers. Press. g To djust the vertil position, press vertil pttern djustment. To djust the horizontl position, press for horizontl pttern djustment. for 3 If the pttern ppers s shown elow, the stithing is misligned in the vertil diretion. Mke the neessry djustments ording to how the pttern is sewn. Vertil pttern djustment If the pttern ppers s shown elow, the stithing is misligned in the horizontl diretion. Press design. to inrese the vertil spe in the If the pttern is not sewn orretly, follow the steps elow to djust the sewing. Press design. to derese the vertil spe in the Sewing the Vrious Built-in Deortive Ptterns 37

140 UTILITY STITCHES Horizontl pttern djustment Press to inrese the horizontl spe in the design. Press to derese the horizontl spe in the design. Press h (Bk key). It returns to the sreen for djusting the pttern. Selet one gin, strt the sewing i mhine nd hek the stithing. Continue djusting the pttern until it is sewn orretly. 38

141 Designing Pttern (My Custom Stith) With the My Custom Stith funtion, you n sew stith ptterns tht you design yourself. Drwing sketh of the pttern Prepre grid sheet set. Mrk the points in the pttern tht re positioned t intersetions in the grid, nd then link those points with ontinuous stright line. Drw sketh of the pttern on the grid sheet set. Drw the pttern s one ontinuous line nd with the strt point nd the end point of the design t the sme height. Determine the sewing order. d For more ttrtive stith, lose the pttern y interseting the line. 3 If the pttern will e repeted, determine the spe etween the repeting ptterns. Designing Pttern (My Custom Stith) 39

142 UTILITY STITCHES Entering the pttern dt e Speify the oordintes of the seond point, nd then press. Follow the pttern drwn on the grid sheet nd progrm the pttern into the sewing mhine. Atth monogrmming foot N. f Repet steps d through e to speify eh point. For detils, refer to Repling the presser foot (pge 44). Press (Utility stith key) on the opertion pnel, nd selet. If you mke mistke entering point, press, nd the previous point is ersed. To orret the ontent entered, press. You n insert, delete nd move points. The sreen for entering pttern ppers. Chek the grid sheet set, nd speify the oordintes of the first point. Speify the oordintes using, nd press. After ll points hve een entered, press. g Speify whether single stithing or triple d stithing will e sewn etween the points. is single stithing, nd gives triple stithing. The sewing sreen ppers. 40

143 Speify the vrious stithing settings, suh s h reverse/reinforement stithing, in the sme wy s with other stithes. To revise the pttern, press. Memo The pttern you entered n e sved for lter use. For detils, refer to Sving ptterns (pge 35). 3 Designing Pttern (My Custom Stith) 4

144 UTILITY STITCHES Exmples of designs Enter eh of the points indited in the tle to sew the smple stith. Point Point Point Point Point Point Point Point

145 4 EMBROIDERY The steps for emroidering re desried in this hpter. Suessful Emroidering...44 Wht to prepre...44 Emroidery step y step...46 Atthing the Emroidery Foot...47 Atthing the emroidery foot Removing the emroidery foot Atthing the Emroidery Unit...50 Emroidery unit preutions...50 Atthing the emroidery unit Removing the emroidery unit Prepring the Fri...53 Atthing n optionl stilizer mteril to the fri...53 Setting the fri in the emroidery frme...54 Atthing the Emroidery Frme Atthing the emroidery frme Removing the emroidery frme Seleting Emroidery Ptterns...59 Copyright informtion...59 Emroidery pttern types...59 LCD (liquid rystl disply) opertion...60 Seleting n emroidery pttern...62 Seleting hrters...63 Seleting frme pttern...64 Using n emroidery rd (sold seprtely)...65 Emroidering...66 Sewing ttrtive finishes...66 Emroidering pttern...67 Appliquéing...69 Editing Ptterns...7 Adjusting the lyout...7 Adjusting the thred tension...73 Adjusting the lternte oin se (with no olor on the srew)...74 Resewing...75 Thred runs out prtwy through design...75 Stopping while emroidering...76 Using the Memory Funtion...78 Emroidery dt preutions...78 Sving ptterns...80 Trnsferring emroidery ptterns from the omputer to mhine...8

146 EMBROIDERY Suessful Emroidering This setion desries the preprtions nd si proedures for emroidering. Wht to prepre The following is neessry for emroidering. Fri Prepre the fri for emroidery. Prepre piee of fri little lrger thn the emroidery frme tht mthes the size of the pttern you wnt to sew. Note Alwys use stilizer when sewing emroidery projets, espeilly when emroidering on lightweight or streth fris. Not using stilizer my result in poor qulity emroidery designs. When emroidering on lrge piees of fri, rrnge the fri so tht it does not hng off the tle where the sewing mhine is pled. If emroidery is done with the fri hnging off, the emroidery unit movement my e impired, this ould use the pttern to sew inorretly. CAUTION Do not emroider fris tht re too thik. To hek the fri thikness, tth the emroidery frme to the emroidery unit, nd use ( Needle Position utton) to rise the needle. If there is spe etween the presser foot nd the fri, the fri n e emroidered. If there is not spe, do not emroider the fri. Otherwise, the needle my rek, resulting in injury. Be reful when sewing overlpping ptterns. The needle my not esily piere the fri, using the needle to rek. Stilizer mteril Atth stilizer mteril for emroidery to the fri to prevent poor qulity emroidery designs. We reommend stilizer mteril for emroidery. Use wter solule sheet on thin mterils like orgndy nd fris with np like towels. For detils, refer to Optionl essories (pge 2). Emroidery thred For the upper thred, use the emroidery thred or ountry thred. For the oin thred, use the emroidery oin thred. For detils, refer to Optionl essories (pge 2). Note For good qulity emroidery designs e sure to use emroidery thred designed for emroidery mhines. Before strting to sew, e sure there is enough oin thred. If you ontinue emroidering when the oin thred is low, the thred my eome tngled. 44

147 Needle Use 75/ home sewing mhine needle. When emroidering on thik fris suh s denim, use 90/4 home sewing mhine needle. Memo A 75/ needle is lredy instlled when the sewing mhine is purhsed. When repling the needle, refer to Repling the needle (pge 42). CAUTION Sine ll point needles (gold olored) re needles for fris where stithes re esily skipped, suh s pttern stithing nd streth fris, e solutely sure not to use them for emroidery. The needle my rek or end. Other Emroidery frmes smll nd medium re optionl. For detils, refer to Optionl essories (pge 2). 4 Suessful Emroidering 45

148 EMBROIDERY Emroidery step y step The si steps for emroidery re s follows. Presser foot tthment 2 Cheking the needle 3 Emroidery unit tthment 4 Repling the oin se 5 Boin thred setup 6 Fri preprtion 7 Emroidery frme tthment 8 Pttern seletion 9 Cheking the lyout 0 Emroidery thred setup Atth the emroidery foot Q. For detils on tthing the emroidery foot, refer to Atthing the emroidery foot (pge 47). Use needle mthed to the fri. For detils on repling the needle, refer to Repling the needle (pge 42). Atth the emroidery unit. For detils on tthing the emroidery unit, refer to Atthing the emroidery unit (pge 50). When using other kinds of emroidery oin thred, use the optionl lternte oin se (no olor on the srew). For detils on repling the oin se, refer to Clening the re (pge 84). For the oin thred, wind emroidery oin thred nd set it in ple. For detils on setting up the oin thred, refer to Winding/Instlling the Boin (pge 25). Atth stilizer mteril to the fri, nd hoop it in n emroidery frme. For detils on prepring the fri, refer to Prepring the Fri (pge 53). Atth the emroidery frme to the emroidery unit. For detils on tthing the emroidery frme, refer to Atthing the Emroidery Frme (pge 57). Selet n emroidery pttern. For detils on seleting emroidery ptterns, refer to Seleting Emroidery Ptterns (pge 59). Chek nd djust the size nd position of the emroidery. For detils on djusting the lyout, refer to Adjusting the lyout (pge 7). Set up emroidery thred ording to the pttern. For detils on setting up the thred, refer to Upper Threding (pge 3). 46

149 Atthing the Emroidery Foot This setion desries how to tth the emroidery foot. Atthing the emroidery foot Atth the emroidery foot when emroidering. Hve the inluded emroidery foot Q nd srewdriver redy. CAUTION Before repling the presser foot, e sure to turn off the sewing mhine, otherwise injuries my our if ( Strt/Stop utton) is identlly pressed nd the mhine strts sewing. Rise the presser foot lever. 2 Emroidery foot r Cught y the presser foot holder srew CAUTION Alwys use the emroidery foot Q when emroidering. If the wrong presser foot is used, the needle my hit the presser foot nd rek or end. Press ( Needle Position utton) one or twie to rise the needle. d Presser foot lever The presser foot is rised. At the time of purhse, the presser foot lever is up. Press nd hold the lk utton on the k of the presser foot holder to deth the presser foot. 4 Needle Position utton The needle goes up. Turn off the sewing mhine. Blk utton Presser foot holder Atthing the Emroidery Foot 47

150 EMBROIDERY e Loosen the presser foot holder srew nd remove the presser foot holder. Turn the srewdriver towrd the k. Seure the emroidery foot with the presser h foot holder srew. Set the emroidery foot perpendiulr. f Srewdriver Presser foot holder Presser foot holder srew Hold the emroidery foot with your right hnd, s shown. Hold the emroidery foot with your index finger wrpped round the lever t the k of the foot. i Mounting noth Presser foot holder srew Firmly tighten the presser foot holder srew. Turn the srewdriver towrd the front. g Lever Emroidery foot r While pressing in the lever with your finger, fit the emroidery foot r over the needle lmp srew to tth the emroidery foot to the presser foot r. 2 CAUTION Do not hit the needle with your finger or the emroidery foot Q when tthing it. The needle my rek or use injury. Be sure to tighten the srew with the inluded srewdriver. If the srew is loose, the needle my hit the presser foot nd rek or end. Before sewing, lwys turn the hndwheel towrd you (ounterlokwise) slowly to mke sure tht the needle does not hit the presser foot. Otherwise, the needle my rek or end. Emroidery foot r Needle lmp srew 48

151 Removing the emroidery foot Press ( Needle Position utton) one or twie to rise the needle. d While pressing in the lever t the k of the emroidery foot with your finger, loosen the presser foot holder srew, nd then remove emroidery foot Q. Turn the srewdriver towrd the k. Needle Position utton Turn off the sewing mhine. Atth the presser foot holder. e For detils, refer to Atthing the presser foot holder (pge 46). CAUTION Before removing the emroidery foot, e sure to turn off the sewing mhine. Otherwise, injuries my our if one of the opertion uttons is identlly pressed nd the mhine strts sewing. 4 Rise the presser foot lever. Presser foot lever The presser foot is rised. Atthing the Emroidery Foot 49

152 EMBROIDERY Atthing the Emroidery Unit This setion desries how to tth the emroidery unit. Emroidery unit preutions Cutions for the emroidery unit will e explined elow. CAUTION Do not move the sewing mhine with the emroidery unit in ple. The emroidery unit my e dropped nd use injury. Keep your hnds nd other ojets wy from the emroidery rrige nd frme. Otherwise injury my result. Note Do not touh the onnetor in the emroidery unit onnetor slot. The onnetor ould e dmged, nd it my use mlfuntions. Do not lift up on the emroidery rrige, nd do not forefully move it. It my use mlfuntions. Atthing the emroidery unit Get the inluded emroidery unit redy. Turn off the sewing mhine. Pull the flt ed tthment off to the left. Slide the t on the over of the onnetion port in the diretion of the rrow to open the over. Note Be sure to lose the over of the onnetion port when the emroidery unit is not eing used. 50

153 d Slide the emroidery unit onto the sewing mhine rm. Push it in until it liks nd stops. CAUTION Do not put your hnds or other ojets ner the rrige. It my use injury. Note If the mhine is initilized with hnds or ojets ner the rrige, the sreen my return to the initil disply. After removing whtever is ner the rrige, turn the power on gin. The emroidery unit is tthed. The sreen for seleting the emroidery pttern type is displyed. Turn on the sewing mhine. e f The onfirmtion messge is displyed. Be sure tht no ojets or hnds re ner the emroidery unit nd press. For detils on the emroidery ptterns, refer to Seleting Emroidery Ptterns (pge 59). Memo Utility stithes nnot e seleted when the emroidery unit is tthed. 4 When n nimtion is displyed on the sreen, the messge ove will e displyed if you touh the sreen with your finger. The rrige moves to its initil position. Crrige Atthing the Emroidery Unit 5

154 EMBROIDERY Removing the emroidery unit Mke sure tht the sewing mhine is ompletely stopped nd follow the instrutions elow. d Hold the relese utton on the ottom left of the emroidery unit, nd slowly pull the emroidery unit to the left. Remove the emroidery frme. For detils on removing the emroidery frme, refer to Removing the emroidery frme (pge 58). Press, nd then press. The emroidery rrige moves into position where it n e stored. Turn off the sewing mhine. Relese utton The emroidery unit seprtes from the sewing mhine. CAUTION Do not rry the emroidery unit y holding the relese utton omprtment. CAUTION Alwys turn off the sewing mhine efore removing the emroidery unit. It my use mlfuntions if removed when the mhine is turned on. 52

155 Prepring the Fri After tthing stilizer mteril to the emroidery fri, it is strethed on n emroidery frme. Atthing n optionl stilizer mteril to the fri Atth stilizer mteril for emroidery to the fri to prevent poor qulity emroidery designs. Prepre stilizer mteril tht is lrger thn the emroidery frme eing used. Memo We reommend the stilizer mteril for emroidery. Use wter solule stilizer on thin mterils like orgndy nd fris with np like towels. For detils, refer to Optionl essories (pge 2). 2 3 Fri Size of emroidery frme Stilizer mteril If you re using stilizers with dhesive, ple the dhesive surfe of the stilizer mteril ginst the wrong side of the fri, nd iron it with stem iron. 4 Note Alwys use stilizer mteril for emroidery with streth fris, thin fris, fris with loose weve nd fris where stithes esily ontrt. 2 3 CAUTION Alwys use stilizer mteril when sewing emroidery projets. The needle my rek or end if you emroider without using stilizer mteril for thin fris or streth fris. Furthermore, the pttern my e sewn inorretly. Stilizer mteril Fri (wrong side) Atthed surfe When it nnot e ironed or pled in the hoop. For fris, suh s towels, whih nnot e ironed or for emroidering in ples where ironing is diffiult, ple the stilizer mteril under the fri, nd streth the fri in the emroidery frme without tthing the stilizer. Prepring the Fri 53

156 EMBROIDERY Setting the fri in the emroidery frme The fri is strethed in the emroidery frme. If the fri is loose, the qulity of the emroidery pttern my e poor. Put the fri in the frme without slk following the steps elow. Hve fri with stilizer mteril tthed nd the emroidery frme (medium, smll, lrge or extr lrge (multi-position)) redy. Emroidery frme (lrge) Emroidery n e done in n re with height of up to 8 m (7 inhes) nd width of up to 3 m (5 inhes). This is used to emroider multiple ptterns without hnging the fri position in the frme. Emroidery frme (medium)[option] Ptterns with height of up to 0 m (4 inhes) nd width of up to 0 m (4 inhes) n e sewn. CAUTION Use the emroidery frme tht mthes the size of the pttern eing emroidered. Otherwise, the emroidery frme my e hit y the presser foot nd use injury or needle rekge. Loosen the emroidery frme djustment srew nd remove the inner nd outer frmes, pling the outer frme on flt surfe. Seprte the inner nd outer frme y removing inner frme upwrd. Inner frme Outer frme Adjustment srew Ple the fri with the stilizer mteril on top of the outer frme. Hve the right side of the loth up. 2 3 Emroidery frme (smll)[option] Ptterns with height of up to 2 m ( inh) nd width of up to 6 m (2-/2 inhes) n e sewn. This is used for letters nd other smll emroidery. Right side There re ptterns for whih emroidery frme (smll) nnot e used. Emroidery frme (extr lrge (multi-position)) Emroidery n e done in n re with height of up to 30 m (2 inhes) nd width of up to 3 m (5 inhes). This is used to emroider onneted or omined hrters or ptterns, or lrge ptterns. Press the inner frme in from the top of the fri. Line up on the inner frme nd on outer frme. 54

157 d Tighten the djustment srew y hnd just enough to seure the fri. Tighten the djustment srew while removing g ny slk in the fri y hnd. The gol is to hve drum-like sound when the strethed fri is struk lightly. e Gently remove the fri from the frme without loosening the djustment srew. Using emroidery sheets If the emroidery sheet tthed to the emroidery frme is used, the emroidery n e sewn in extly the right position on the fri. Memo This preutionry step will help redue pttern distortion while emroidering. 4 Press the inner frme in from the top of the f fri gin, lining up on the inner frme nd on outer frme. Mke mrk with hlk pen t the enter of the position for the pttern to e emroidered. 2 3 Emroidery pttern Mrk Outer frme Inner frme Fri (right side) d Stilizer mteril e Ledge of outer frme Press down firmly until the inner frme is seurely pressed ginst the ledge of the outer frme. Prepring the Fri 55

158 EMBROIDERY Ple the emroidery sheet on the inner frme. 3 2 Emroidery on fris tht nnot e strethed on n emroidery frme When smll piees of fri tht nnot e strethed on n emroidery frme or thin piees like rion re eing emroidered, use stilizer mteril s se to streth on the frme. We reommend stilizer mteril for ll emroidery. Emroidery sheet Inner frme Emroidery sheet se lines Line the mrk on the fri up with the se line on the emroidery sheet. Ple the inner frme with the fri on the d outer frme nd streth the fri. For detils, refer to pge 54. Remove the emroidery sheet. e Stilizer mteril Tk or spry glue Fri After ompleting the emroidery, remove the stilizer mteril refully. 56

159 Atthing the Emroidery Frme This setion desries how to tth the emroidery frme. Atthing the emroidery frme Wind the emroidery oin thred onto the oin nd set it into the oin se. For detils, refer to Winding/Instlling the Boin (pge 25). Rise the presser foot lever. Lever 2 Presser foot lever 4 Pss the emroidery frme under the presser foot while rising the presser foot lever even further. Mounting rkets Pins 2 3 d CAUTION Do not hit the needle with your finger or the emroidery frme. It my use injury or needle rekge. While lightly holding the lever on the frme holder to the left, lign the two pins on the emroidery frme holder with the mounting rkets on the frme, nd then press the frme into the emroidery frme holder until lik is herd. After pressing the front mounting rket onto the pin so tht it liks into ple, press the k mounting rket into ple. Note Be sure to insert oth pins. If only the forwrd or the k pin is inserted, the pttern my not turn out orretly. CAUTION Corretly set the emroidery frme into the emroidery frme holder. Otherwise, the presser foot my hit the emroidery frme, resulting in injury. Atthing the Emroidery Frme 57

160 EMBROIDERY Removing the emroidery frme Pss the emroidery frme under the presser foot while rising the presser foot lever even further. Mke sure tht the sewing mhine is ompletely stopped nd follow the instrutions elow. Rise the presser foot lever. Presser foot lever CAUTION Do not hit the needle with your finger or the emroidery frme. It my use injury or needle rekge. While pushing the lever of the emroidery frme holder to the left, lift the emroidery frme up to remove it. Remove the k mounting rket from the pin, nd then remove the front mounting rket from the pin. Lever 2 2 Mounting rkets Pins 3 58

161 Seleting Emroidery Ptterns This setion provides detils on the vrious types of emroidery ptterns ville nd the proedure for seleting pttern. Copyright informtion The ptterns sved in the sewing mhine nd emroidery rds re intended for privte use only. Any puli or ommeril use of opyrighted ptterns is n infringement of opyright lw nd is stritly prohiited. Emroidery pttern types An emroidery pttern n e seleted from the following types ville. d e f g Emroidery ptterns Additionl emroidery ptterns Alphet ptterns d Frme ptterns e Emroidery rd f Ptterns sved in the mhine's memory g Ptterns retrieved from USB flsh drive (USB flsh memory) Emroidery ptterns (Emroidery ptterns/ Additionl emroidery ptterns) There re totl 36 ptterns. The ptterns re ompleted y hnging the upper thred ording to the instrutions displyed on the sreen. For detils, refer to Seleting n emroidery pttern (pge 62). Alphet ptterns There re 6 types of hrters (Europen hrters); upper se/lower se/numers/ symols. For detils, refer to Seleting hrters (pge 63). Frme ptterns 0 shpes, suh s squres nd irles, n e omined with 2 stith types. For detils, refer to Seleting frme pttern (pge 64). Emroidery rd (sold seprtely) Ptterns from n emroidery rd n e emroidered. For detils, refer to Using n emroidery rd (sold seprtely) (pge 65). Ptterns sved in the mhine's memory Ptterns, suh s frequently used hrter omintions, n e sved in the mhine s memory to e retrieved lter nd emroidered. Ptterns onsisting of up to 2 ptterns or 52 KB n e sved. For detils, refer to Sving ptterns (pge 80). Ptterns retrieved from USB flsh drive (USB flsh memory) Ptterns retrieved from USB medi n e emroidered. Note Only USB flsh drive (USB flsh memory) n e onneted to the USB port on this mhine. For detils, refer to Trnsferring emroidery ptterns from the omputer to mhine (pge 8). 4 Seleting Emroidery Ptterns 59

162 EMBROIDERY LCD (liquid rystl disply) opertion The LCD (liquid rystl disply) is operted using the opertion keys on the opertion pnel. The use of the keys for emroidery will e explined elow. Opertion keys DISPLAY UNIT The mesurement units tht re displyed n e seleted. [mm/inh] EMBROIDERY TENSION The thred tension for emroidering n e djusted. [-8 to +8] Returns to the previous sreen. MAX EMBROIDERY SPEED (SPM) The mximum emroidering speed n e seleted. [650SPM/350SPM] Press When there re ptterns tht re not displyed on the sreen (when or is displyed), the previous ptterns/susequent ptterns re displyed. Returns to the type seletion sreen. The seleted pttern is nelled. Press this key to djust lnguge or hnge the thred olor disply or other settings. (Settings key). NAME OF COLOR: Typil olor nme TIME: Time required for emroidering NEEDLE COUNT: Needle progress numer #23: Selet from the following thred olor numer sets EMBROIDERY (POLYESTER) THREAD# COUNTRY (COTTON) THREAD# MADEIRA POLY THREAD# MADEIRA RAYON THREAD# SULKY THREAD# ROBISON-ANTON POLY THREAD# 60

163 LCD utton When speifi pttern is seleted, press this key nd then, press to swith the disply. The sewing settings suh s the speified lphet hrter string nd olor re onfirmed. The needle progresses one olor or one stith (if pressed ontinuously, 9 stithes to 20 stithes) t time nd hnges the position for strting the emroidery. This is used when speifi olor is not sewn or when restrting the sewing mhine fter power hs een turned off in the middle of the opertion. Press this key to hnge the thred settings. Bk one olor Bk one stith Forwrd one olor Forwrd one stith 4 For detils, refer to Resewing (pge 75). Press this key to selet or nel progrmmed thred utting. The position of the pttern within the emroidery frme n e heked, nd the size nd ngle n e hnged. Press or to djust the thred tension. Press or to hnge the thred density (hrter ptterns only). Press this key to djust the pttern. For detils, refer to Adjusting the lyout (pge 7). Memo Keys tht pper surrounded with dotted line nnot e used. Press this key when you wnt to hnge the olor hrter y hrter in hrter emroidery. Sine the sewing mhine stops t the end of eh hrter, the upper thred is hnged s you sew. Press this key gin to nel multi-olor. Seleting Emroidery Ptterns 6

164 EMBROIDERY Seleting n emroidery pttern There re totl of 36 emroidery ptterns, suh s fruits nd nimls, sved in the mhine's memory. Selet the pttern. Swith the sreen using (Previous pge key) nd (Next pge key). 70 Emroidery ptterns 66 Emroidery ptterns Memo Refer to Emroidery Pttern Color Chnge Tle in the Quik referene guide for smples of ompleted ptterns nd the thred used. When / is pressed, the disply of ptterns moves forwrd or kwrd in inrements of 0 designs. Selet the type of the emroidery pttern. When pttern is seleted, it n e emroidered. The pttern seletion sreen is displyed. 62

165 Seleting hrters Speify the hrters for emroidery. Memo When The pttern is too lrge for the emroidery frme. is displyed, no more hrters n e input. Chrters of different styles (sns serif, serif, nd outline, et.) nnot e omined. Selet the hrter stithes. 4 Selet the hrter style. Selet the hrters. If wrong hrter ws seleted, press. To enter spe, press _. Exmple: Welome Swith etween upperse/lowerse Swith mong lrge/medium/smll sizes Seleting Emroidery Ptterns 63

166 EMBROIDERY Selet the frme shpe. Swith the sreen using (Previous pge key) (Next pge key), nd selet from the ten types. Memo The hrter pttern tht you reted n e sved for lter use. For detils, refer to Sving ptterns (pge 80). Seleting frme pttern 0 shpes, suh s squres nd irles, n e omined with 2 stith types. Memo Refer to Frme ptterns in the Quik referene guide for frme pttern shpes nd stithes. The stith seletion sreen is displyed. Selet the stith. Swith the sreen using (Previous pge key) (Next pge key), nd selet from the 2 stithes. Press the frme pttern. The frme shpe seletion sreen is displyed. When stith is seleted, it n e emroidered. 64

167 Using n emroidery rd (sold seprtely) If n emroidery rd is used, you n emroider ptterns other thn the ptterns sved in the sewing mhine. There re vrious rds with different themes. Insert the emroidery rd in the emroidery rd slot on the right side of the sewing mhine. Fe the rrow on the emroidery rd towrd you, nd insert it in the diretion of the rrow. Note Alwys turn off the sewing mhine to insert nd remove emroidery rds. Insert the emroidery rd into the emroidery rd slot, fing it in the right diretion. Do not put nything other thn n emroidery rd in the emroidery rd slot. When emroidery rds re not in use, keep them in their storge ses. Use only emroidery rds mnuftured for this mhine. Using unuthorized rds my use your mhine to operte inorretly. Emroidery rds purhsed in foreign ountries my not work with your mhine. Lrge ptterns supplied on emroidery rds my e diffiult to view on the sreen. Turn on the sewing mhine. Press the emroidery rd on the sreen. d 4 Turn off the sewing mhine. e The seletion sreen for the ptterns sved in the rd is displyed. Selet pttern. The opertion is the sme s in Seleting Emroidery Ptterns (pge 59). Seleting Emroidery Ptterns 65

168 EMBROIDERY Emroidering After the preprtions re done, you n try emroidering. This setion desries the steps for emroidering nd ppliquéing. Sewing ttrtive finishes There re mny ftors tht go into sewing eutiful emroidery. Using the pproprite stilizer (pge 53) nd hooping the fri in the frme (pge 54) re two importnt ftors mentioned erlier. Another importnt point is the ppropriteness of the needle nd thred eing used. See the explntion of threds elow. Inluded with this mhine re two oin ses. Follow the explntion elow. Thred Upper thred Boin thred Use emroidery thred, or ountry emroidery thred intended for use with this mhine. Other emroidery threds my not yield optimum results. Use emroidery oin thred intended for use with this mhine. Memo If you use threds other thn those listed ove, the emroidery my not sew out orretly. Boin se Stndrd oin se (green mrking on the srew) Alternte oin se (no olor on the srew) Stndrd oin se (green mrking on the srew) is in the mhine for sewing nd emroidery. The oin se originlly instlled in the mhine hs green srew. Alternte oin se (no olor on the srew) is set with tighter tension for emroidery with different weights of oin threds nd vriety of emroidery tehniques. This oin se is identified with drk olored mrk on the inside of the oin vity. The srew on this se n e djusted if neessry. For detils on how to remove the oin se, refer to Clening the re (pge 84). For detils on djusting the lternte oin se, refer to Adjusting the lternte oin se (with no olor on the srew) (pge 74). Note Before emroidering, hek tht there is enough thred in the oin. If you ontinue sewing without enough thred in the oin, the thred my tngle. Do not leve ojets in the rnge of motion of the emroidery frme. The frme my strike the ojet nd use poor finish to the emroidery pttern. When emroidering on lrge grments (espeilly jkets or other hevy fris), do not let the fri hng over the tle. Otherwise, the emroidery unit nnot move freely, nd the pttern my not turn out s plnned. 66

169 Emroidering pttern Emroidery ptterns re emroidered with hnge of thred fter eh olor. Prepre emroidery thred of the olor shown on the sreen. Exmple: Emroidery thred numer seleted d e Emroidery frmes tht n e used for emroidering Current olor step/numer of olors in design Current nme of olor d Current olor prt e Next olor prt The thred olor numer set displyed for the thred olors n e hnged. Press (Settings key), nd then hnge the setting in the settings sreen. For detils, refer to LCD (liquid rystl disply) opertion (pge 60). Set the emroidery thred, nd thred the needle. Refer to Threding the upper thred (pge 32) nd Threding the needle (pge 34). Note Before using the needle threder, e sure to lower the presser foot. 4 Pss the thred through the emroidery foot hole, nd hold it lightly in your left hnd. Give the thred little slk. CAUTION If the thred is pulled too tight, the needle my rek or end. Do not let hnds or ojets hit the rrige while sewing. The pttern my mislign. Emroidering 67

170 EMBROIDERY Lower the presser foot lever. d Presser foot lever Press ( Strt/Stop utton). e Press ( Strt/Stop utton) gin. h The emroidery egins gin. i Stithing stops utomtilly with reinforement fter one olor hs een ompleted. When utomti thred utting is set, the thred is ut. Set up emroidery thred for the next olor, nd repet steps through h. Cut the exess thred. j When the lst olor is sewn, Finished sewing. will pper on the disply. Press, nd the disply will return to the initil sreen. Strt/Stop utton Memo For the utomti utting setting, refer to LCD (liquid rystl disply) opertion (pge 60). f g After progressing 5-6 stithes, press ( Strt/Stop utton) to stop the mhine. Use sissors to ut the thred t the eginning of the stithing. Cut the thred t the edge of the stithing. If the thred is left t the eginning of the stithing, it my e sewn over s you ontinue emroidering the pttern, mking it very diffiult to del with the thred fter the pttern is finished. Trim the thred t the eginning. 68

171 Appliquéing Prepre the se fri nd the ppliqué fri (ppliqué piee). Press (Settings key), nd set the thred olor disply to NAME OF COLOR, so APPLIQUE MATERIAL, APPLIQUE POSITION nd APPLIQUE re displyed on the sreen. Selet n ppliqué pttern. d Remove the fri from the emroidery frme, nd ut it out long the ut-out line. Cut refully long the stithing nd remove the thred. If it is not ut right on the stithing, it will not e finished netly. When APPLIQUE MATERIAL is displyed on the sreen, pply iron-on stilizer to the k of the ppliqué piee fri, nd streth it on the emroidery frme. e Streth the se fri on the emroidery frme. Set up the thred for ppliquéing. f Lower the presser foot lever, nd press g ( Strt/Stop utton). The position for the ppliqué is stithed, nd the sewing mhine stops. 4 Lower the presser foot lever, nd press ( Strt/Stop utton). The ut-out for the ppliqué piee is sewn, nd the sewing mhine stops. Appliqué position Bse fri 2 APPLIQUE will e displyed on the sreen. 2 Cut-out line Appliqué piee fri APPLIQUE POSITION will e displyed on the sreen. Apply thin lyer of fri glue or spry h dhesive to the k of the ppliqué piee, nd tth it in the ppliqué position. Emroidering 69

172 EMBROIDERY Lower the presser foot lever, nd press i ( Strt/Stop utton). Note When APPLIQUE MATERIAL, APPLIQUE POSITION nd APPLIQUE re displyed, speifi olor thred does not pper. Use proper olor thred to mth the ppliqué piee. j Follow the instrutions on the sreen, nd hnge thred olors s you sew. 70

173 Editing Ptterns This setion desries wys to edit, djust, nd reposition ptterns. Adjusting the lyout Chek nd djust the lyout. d e f The pttern is normlly positioned in the enter of the emroidery frme. You n hek the lyout efore strting emroidery nd hnge the position nd the size. k g h Memo Keys tht pper surrounded with dotted line nnot e used. After seleting the emroidery pttern, press. The emroidery sreen is displyed. j d e f g h i j k Lyout within the frme Aville emroidery frmes Disply unit (m/inch) Chnge position keys Size key Lyout key Rottion key Horizontl mirror imge key Distne from the enter Emroidery size Strting point key i 4 Press. Emroidery frme size These flsh if the pttern ws resized, the lyout ws djusted, or the reommended emroidery frme size ws hnged. Emroidery frme ions tht pper in gry nnot e used. Size key Inreses/dereses the size of the pttern. Press to return to the previous sreen. The lyout sreen is displyed. Dereses size Returns to originl size Returns to enter position (when the pttern ws moved with the hnge position key) Inreses size Chnge position keys Moves the emroidery position up, down, left nd right. Editing Ptterns 7

174 EMBROIDERY Memo If you mke note of the vlues in the lower prt of sreen when you hnge the size nd position, you n sew with the sme size nd lyout even if you hve to turn the power k on in the middle of your work. Press Strting point key Press this key to move the emroidery frme nd hek the emroidering position or to hnge the needle position efore emroidering. The sreen elow ppers when this key is pressed. to return to the previous sreen. Lyout key Press this key to move to rottion sreen. Moves the needle to the position of the seleted needle strt position. Rottion key Rottes the pttern one degree, 0 degrees or 90 degrees t time. Press (Bk key) to return to the previous sreen. Moves the frme to hek the pttern position. Rottes the pttern 90 degrees to the left Rottes the pttern 90 degrees to the right Rottes the pttern 0 degrees to the left Rottes the pttern 0 degrees to the right Rottes the pttern degree to the left Rottes the pttern degree to the right Returns the pttern to its originl position CAUTION Never lower the needle when the emroidery frme is moving. The needle my rek or end. When you hve revised the pttern, hek the disply of ville emroidery frmes nd use n pproprite frme. If you use n emroidery frme not displyed s ville for use, the presser foot my strike the frme nd possily use injury. Horizontl mirror imge key Mirrors the pttern left nd right. 72

175 Press (Bk key) to return to the d originl sreen. Adjusting the thred tension If emroidery fils, it is diffiult to undo the thred nd the fri my e dmged. Before emroidering, use srp of the sme fri to hek the djustment of the thred tension, et. To djust the thred tension, press (Settings key). Memo When the power is turned off, the lyout returns to the originl setting. You n lso hek the pttern size nd distne from the enter y pressing fter eginning emroidering. Press Press to weken the thred tension. to tighten the thred tension. Corret thred tension The thred tension is orret when upper thred is just visile on k of the fri. 4 Right side Wrong side 2 Upper thred is too tight The lower thred will e visile on the front of the fri. In this instne, derese the upper thred tension. Right side Wrong side 2 Upper thred is too loose The upper thred hs slk. In this instne, inrese the upper thred tension. Right side Wrong side 2 Editing Ptterns 73

176 EMBROIDERY Adjusting the lternte oin se (with no olor on the srew) When using the emroidery oin thred provided, plese e sure to hoose the green mrked oin se when performing utility stith sewing nd emroidery funtions. When in the emroidery funtion mode, the lternte oin se (with no olor on the srew) should e seleted when sustitute emroidery oin threds (other thn wht is ompnied with your mhine) re eing used. The lternte oin se (with no olor on the srew) n e esily djusted when oin tension hnges re required to ommodte different oin threds. Refer to Sewing ttrtive finishes (pge 66). To djust the oin tension for emroidery funtion, using the lternte oin se (with no olor on the srew), turn the slotted srew (-) with (smll) srewdriver. Do not turn phillips srew (+). Adjust with srewdriver (smll). Corret tension Upper thred slightly ppers on the wrong side of fri. Right side Wrong side 2 Boin thred is too loose Boin thred ppers slightly on the right side of fri. Boin thred is too tight Upper thred on the right side of fri seems to e lifting/looping nd oin thred is not seen on the wrong side of fri. Right side Wrong side If this ours, turn the slotted srew (-) ounterlokwise, eing reful not to overloosen the srew, pproximtely degrees to derese oin tension. CAUTION 2 When djusting the lternte oin se, e sure to remove the oin from the lternte oin se. DO NOT djust the position of the phillips (+) srew on the lternte oin se s this my result in dmge to the oin se, rendering it unusle. If the slotted srew (-) is diffiult to turn, do not use fore. Turning the srew too muh or providing fore in either (rottionl) diretion my use dmge to the oin se. Should dmge our, the oin se my not mintin proper tension. Right side Wrong side 2 If this ours, turn the slotted srew (-) lokwise, eing reful not to over-tighten the srew, pproximtely degrees to inrese oin tension. 74

177 Resewing When the wrong upper thred olor hs een sewn, it n e resewn with the orret olor. Press ( Strt/Stop utton) to stop the sewing mhine. Press. Thred runs out prtwy through design When the upper thred or the oin thred runs out while sewing, the sewing mhine stops. Move the needle k out 0 stithes nd resume sewing. Set up the upper or oin thred. Press. Press. Press. 4 Press (Bk one olor) to return to the d eginning of the mistken olor. Press (Bk one stith) to move the d needle k out 0 stithes. (Forwrd one stith) inreses the stith numer. Set up the orret olor for the upper thred. e Press ( Strt/Stop utton) to ontinue f the design. Restrt the emroidery. e Editing Ptterns 75

178 EMBROIDERY Stopping while emroidering If the emroidery is stopped efore it is omplete, hek the urrent needle ount efore turning off the sewing mhine. Press (Emroidery key). Memo When the sewing mhine is turned off, the emroidery size nd lyout return to the originl setting. Press ( Strt/Stop utton) to stop the sewing mhine. The onfirmtion messge is displyed. Press. d Chek the urrent needle ount on the sreen nd mke note of it. The seleted pttern is deleted, nd the sreen for seleting the emroidery pttern type is displyed. If the needle ount is not displyed, press (Settings key), nd then use to disply the following sreen. Turn off the sewing mhine. e f Alwys deth the emroidery unit when you move the sewing mhine. Turn on the sewing mhine nd selet the pttern. Press. g Press (Bk key) to return to the emroidery sreen. 76

179 Press. h Press (Forwrd one olor) to move to i the eginning of the olor you wnt to emroider. Press (Forwrd one stith) to inrese j the needle ount. If is pressed ontinuously, it moves forwrd > 9 > 30 stithes. 4 Move forwrd to out 0 stithes efore the totl numer of stithes onfirmed in. Restrt the emroidery. k Editing Ptterns 77

180 EMBROIDERY Using the Memory Funtion Emroidery dt preutions Oserve the following preutions when using emroidery dt other thn tht reted nd sved in this mhine. CAUTION When using emroidery dt other thn our originl ptterns, the thred or needle my rek when sewing with stith density tht is too fine or when sewing three or more overlpping stithes. In tht se, use one of our originl dt design systems to edit the emroidery dt. Types of Emroidery Dt Tht Cn Be Used Only.pes nd.dst emroidery dt files n e used with this mhine. Using dt other thn tht sved using our dt design systems or sewing mhines my use the emroidery mhine to mlfuntion. Types of USB Medi Tht Cn Be Used Emroidery dt n e relled from USB flsh drive (USB flsh memory) of ny size. Note Only USB flsh drive (USB flsh memory) n e onneted to the USB port on this mhine. Some USB medi my not e omptile with this mhine. Visit our wesite for more detils. When using USB medi equipped with n ess inditor, the ess inditor will egin flshing fter the medi is inserted into your omputer or mhine, nd my tke out 5 to 6 seonds efore the medi is reognized. (The length of time differs depending on the USB medi.) For dditionl informtion, refer to the instrution mnul inluded with the USB medi tht you hve purhsed. Memo Letters nd numerls n e used in file nmes. In ddition, if the file nme ontins no more thn eight hrters, the entire file nme will pper on the sreen. If the file nme is more thn eight hrters long, only the first six hrters followed y ~ nd numer pper s the file nme. This pplies to.dst emroidery dt files only. Only the nmes of.dst files re displyed. Preutions on Using the Computer To Crete nd Sve Dt If the file nme of emroidery dt nnot e identified, for exmple, euse the nme ontins speil hrters, the file will not e displyed. If this ours, hnge the nme of the file. We reommend using the 26 letters of the lphet (upperse nd lowerse), the numers 0 through 9, -, nd _. All designs must e within the 8 m (H) 3 m (W) (Approx. 7 inhes (H) 5 inhes (W)) design field size. If the seleted pttern does not fit within the 8 m (H) 3 m (W) (Approx. 7 inhes (H) 5 inhes (W)) design field size unless it is rotted 90 degrees, messge ppers, sking if you wish to rotte the pttern 90 degrees..pes files sved with the numer of stithes, the numer of olors nd the numer of omined ptterns exeeding the speified limits nnot e displyed. Use one of our originl dt design systems to edit the emroidery pttern so tht it meets the required speifitions. Even if the emroidery unit is not tthed, the mhine will reognize emroidery dt. Sve the ptterns in the root diretory of the USB medi. If emroidery dt is sved in folder on USB medi, tht emroidery dt nnot e retrieved y the mhine. 78

181 Tjim (.dst) Emroidery Dt When.dst file is imported, the only wy tht you n view the design is y seleting the pttern (file nme). Then press to disply the design on the sreen. 4 Using the Memory Funtion 79

182 EMBROIDERY Sving ptterns The emroidery ptterns nd the lphet hrters you hve ustomized n e sved in the sewing mhine's memory. Sine the sved ptterns will not e ersed when the power is turned off, you n lwys retrieve them for emroidery. This is onvenient for sving nmes nd the like. You n sve up to 2 ptterns or 52 KB of dt. Sving pttern After seleting the pttern to e sved, press (Memory key). Selet the pttern you wish to retrieve. Swith sreens using (Previous pge key) nd (Next pge key). Totl mount of memory used Totl mount of memory spe Numer of the urrently displyed pge from the totl numer of pges The seleted pttern is shown in reverse highlighting. Press. To delete the sved pttern, press. After the pttern is sved, the initil sreen ppers gin. Note Do not turn off the sewing mhine while the pttern is eing sved, otherwise the pttern dt my e lost. The sved pttern is retrieved. The emroidery sreen ppers, nd you n emroider the retrieved pttern. Retrieving pttern. Press. The sved ptterns re displyed. Note Chrters sved from n emroidery rd must hve the emroidery rd inserted in the mhine in order to retrieve the memory sved from the emroidery rd. 80

183 Trnsferring emroidery ptterns from the omputer to mhine Copy the pttern dt to Removle Disk. Note Only USB flsh drive (USB flsh memory) n e onneted to the USB port on this mhine. An emroidery pttern n e trnsferred to the mhine from USB medi ontining dt for no more thn 200 emroidery ptterns. Emroidery ptterns nnot e trnsferred to the mhine if the USB medi ontins dt for more thn 200 emroidery ptterns. In this se, redue the numer of designs sved on the USB medi. In ddition, if the emroidery designs ontin too mny olors (this numer my vry within the designs themselves), it my not e possile to trnsfer n emroidery pttern to the mhine, even if there re less thn 200 emroidery ptterns tht hve een sved on the USB medi. In this se lso, redue the numer of designs sved on the USB medi. Sve the ptterns in the root diretory of the USB medi. If emroidery dt is sved in folder on USB medi, tht emroidery dt nnot e retrieved y the mhine. Insert the USB medi into the USB port on the omputer. USB port on the omputer USB medi The Removle Disk ion ppers in Computer (My omputer) on the omputer. d Sfely remove the USB medi from the USB port on the omputer. USB port on the omputer USB medi CAUTION Before disonneting the USB medi, lik the Unplug or Ejet Hrdwre ion in the tskr of Windows 2000 or the Sfely Remove Hrdwre ion in the tskr of Windows XP/Windows Vist. Then, when the removle disk n sfely e removed, disonnet the USB medi from the omputer. Windows XP Windows Vist 4 Using the Memory Funtion 8

Operation Manual GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX. Computerized Sewing Machine Product Code: 888-V12/V13/V15

Operation Manual GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX. Computerized Sewing Machine Product Code: 888-V12/V13/V15 GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX Opertion Mnul Computerized Sewing Mhine Produt Code: 888-V12/V13/V15 Be sure to red this doument efore using the mhine. We reommend tht you keep this

More information

CONGRATULATIONS ON CHOOSING OUR MACHINE PLEASE READ BEFORE USING THIS MACHINE

CONGRATULATIONS ON CHOOSING OUR MACHINE PLEASE READ BEFORE USING THIS MACHINE CONGRATULATIONS ON CHOOSING OUR MACHINE Your mhine is the most dvned omputerized household sewing mhine. To fully enjoy ll the fetures inorported, we suggest tht you study the mnul. PLEASE READ BEFORE

More information

Operation Manual GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX. Computerized Sewing Machine

Operation Manual GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX. Computerized Sewing Machine GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX Opertion Mnul Computerized Sewing Mhine Importnt Sfety Instrutions Plese red these sfety instrutions efore ttempting to use the mhine. This mhine is

More information

GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX. Operation Manual. Computerized Sewing Machine

GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX. Operation Manual. Computerized Sewing Machine GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX Opertion Mnul Computerized Sewing Mhine Importnt Sfety Instrutions Plese red these sfety instrutions efore ttempting to use the mhine. This mhine is

More information

Operation Manual GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX. Computerized Sewing Machine Product Code: 888-V14

Operation Manual GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX. Computerized Sewing Machine Product Code: 888-V14 GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX Be sure to red this doument efore using the mhine. We reommend tht you keep this doument nery for future referene. Opertion Mnul Computerized Sewing

More information

Operation Manual. Read before use. Read when additional information is required. GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX

Operation Manual. Read before use. Read when additional information is required. GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX GETTING READY Red efore use. SEWING BASICS UTILITY STITCHES Red when dditionl informtion is required. APPENDIX Computerized Sewing Mhine Produt Code: 885-U24 Opertion Mnul IMPORTANT SAFETY INSTRUCTIONS

More information

Operation Manual. Product Code 885-V51. Computerized Embroidery Machine GETTING READY EMBROIDERY APPENDIX

Operation Manual. Product Code 885-V51. Computerized Embroidery Machine GETTING READY EMBROIDERY APPENDIX Computerized Emroidery Mhine Opertion Mnul Produt Code 885-V51 GETTING READY EMBROIDERY APPENDIX Plese visit us t http://solutions.rother.om where you n get produt support nd nswers to frequently sked

More information

Operation Manual Sewing Machine

Operation Manual Sewing Machine Opertion Mnul Sewing Mhine Produt Code: 888-S33/S36 KNOWING YOUR SEWING MACHINE SEWING BASICS UTILITY STITCHES APPENDIX Be sure to red this doument efore using the mhine. We reommend tht you keep this

More information

Operation Manual. Sewing Machine. Product Code: 888-F42

Operation Manual. Sewing Machine. Product Code: 888-F42 Opertion Mnul Sewing Mhine Produt Code: 888-F42 Be sure to red this doument efore using the mhine. We reommend tht you keep this doument nery for future referene. INTRODUCTION INTRODUCTION Thnk you for

More information

Operation Manual GETTING READY SEWING BASICS UTILITY STITCHES EMBROIDERY APPENDIX. Easy Thread Cassette System

Operation Manual GETTING READY SEWING BASICS UTILITY STITCHES EMBROIDERY APPENDIX. Easy Thread Cassette System SE-BrotherE_sgml.ook Pge Mondy, June 30, 003 3:44 PM GETTING READY SEWING BASICS UTILITY STITCHES EMBROIDERY APPENDIX CPS5XV[Y Esy Thred Cssette System Opertion Mnul Inluded Aessories After opening the

More information

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS INTRODUCTION INTRODUCTION Thnk you for purhsing this mhine. Before using this mhine, refully red the IMPORTANT SAFETY INSTRUCTIONS, nd then study this mnul for the orret opertion of the vrious funtions.

More information

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS INTRODUCTION INTRODUCTION Thnk you for purhsing this mhine. Before using this mhine, refully red the IMPORTANT SAFETY INSTRUCTIONS, nd then study this mnul for the orret opertion of the vrious funtions.

More information

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS INTRODUCTION INTRODUCTION Thnk you for purhsing this mhine. Before using this mhine, refully red the IMPORTANT SAFETY INSTRUCTIONS, nd then study this mnul for the orret opertion of the vrious funtions.

More information

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS INTRODUCTION INTRODUCTION Thnk you for purhsing this mhine. Before using this mhine, refully red the IMPORTANT SAFETY INSTRUCTIONS, nd then study this mnul for the orret opertion of the vrious funtions.

More information

SERVICE MANUAL 9940/20/10

SERVICE MANUAL 9940/20/10 9940/0/0 9/0/00 Tle of ontents REMOVING THE EXTERIOR PARTS... A. Light Cover... B. Bse... C. Top Cover (Flp)... 4 D. Hinge Cover... 4 E. Thred Tension Cover... 4 F. Side Enlosure... 5 G. Hndle nd Unit

More information

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS When using this mhine, si sfety preutions should lwys e tken, inluding the following: Red ll instrutions efore using. DANGER - To redue the risk of eletri shok: 1. The mhine

More information

Operation Manual. Product Code 885-V55. Computerized Embroidery Machine GETTING READY EMBROIDERY APPENDIX

Operation Manual. Product Code 885-V55. Computerized Embroidery Machine GETTING READY EMBROIDERY APPENDIX Computerized Emroidery Mchine Opertion Mnul Product Code 885-V55 GETTING READY EMBROIDERY APPENDIX Be sure to red this document efore using the mchine. We recommend tht you keep this document nery for

More information

Operation Manual Sewing Machine

Operation Manual Sewing Machine Opertion Mnul Sewing Mchine Product Code: 888-V64/V65/V66/V67 KNOWING YOUR SEWING MACHINE SEWING BASICS UTILITY STITCHES APPENDIX Be sure to red this document efore using the mchine. We recommend tht you

More information

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS INTRODUCTION INTRODUCTION Thnk you for purchsing this mchine. Before using this mchine, crefully red the IMPORTANT SAFETY INSTRUCTIONS, nd then study this mnul for the correct opertion of the vrious functions.

More information

Operation Manual Sewing

Operation Manual Sewing Opertion Mnul Sewing Emroidery nd Sewing Mhine Produt Code: 882-W30 Be sure to red this mnul efore using the mhine. We reommend tht you keep this doument nery for future referene. INTRODUCTION INTRODUCTION

More information

Operation Manual. Sewing Machine KNOWING YOUR SEWING MACHINE SEWING BASICS UTILITY STITCHES APPENDIX

Operation Manual. Sewing Machine KNOWING YOUR SEWING MACHINE SEWING BASICS UTILITY STITCHES APPENDIX Opertion Mnul Sewing Mchine Product Code: 885-V58/V59/V68/V69 KNOWING YOUR SEWING MACHINE SEWING BASICS UTILITY STITCHES APPENDIX Be sure to red this document before using the mchine. We recommend tht

More information

IMPORTANT SAFETY INSTRUCTIONS. Please read these safety instructions before attempting to use the machine.

IMPORTANT SAFETY INSTRUCTIONS. Please read these safety instructions before attempting to use the machine. INTRODUCTION INTRODUCTION Thnk you for purhsing this emroidery nd sewing mhine. Before using this mhine, refully red the IMPORTANT SAFETY INSTRUCTIONS, nd then study this mnul for the orret opertion of

More information

For installation help please visit Please Do Not Return Product to Store!

For installation help please visit   Please Do Not Return Product to Store! Instlltion Guide Replement Sreen Housing for ndersen Luminire Retrtle Inset Sreen Door For instlltion help plese visit www.ndersenluminire.om/instll Plese Do Not Return Produt to Store PLESE ll the Storm

More information

Operation Manual. Embroidery Machine. Product Code: 888-M30/M31

Operation Manual. Embroidery Machine. Product Code: 888-M30/M31 Opertion Mnul Emroiery Mhine Prout Coe: 888-M30/M31 Be sure to re this oument efore using the mhine. We reommen tht you keep this oument nery for future referene. INTRODUCTION Thnk you for purhsing this

More information

Operation Manual Embroidery

Operation Manual Embroidery Opertion Mnul Emroidery Emroidery nd Sewing Mchine Product Code: 882-W30 Be sure to red this mnul efore using the mchine. We recommend tht you keep this document nery for future reference. HOW TO USE

More information

MODEL 351 POWERGLIDE SERIES INSTRUCTIONS FOR INSTALLING SARGENT DOOR CLOSERS WITH "H" HOLDER ARMS

MODEL 351 POWERGLIDE SERIES INSTRUCTIONS FOR INSTALLING SARGENT DOOR CLOSERS WITH H HOLDER ARMS MODEL POWERGLIDE SERIES INSTRUTIONS FOR INSTLLING SRGENT LOSERS WITH "H" HOLDER S SERIES NON SIZED DJUSTLE SIZES THRU 6 UTION: FILURE TO INSTLL OR DJUST PROPERLY MY RESULT IN INJURY OR DMGE. FOR SSISTNE,

More information

* * 98/9949WDC. 1-Point Latch (LBL) 2-Point Latch includes these additional parts. Customer Service

* * 98/9949WDC. 1-Point Latch (LBL) 2-Point Latch includes these additional parts. Customer Service *24017501* 24017501 Coneled Vertil Devie for Wood Doors 98/9949WDC Instlltion Instrutions 1-Point Lth (LBL) 2-Point Lth inludes these dditionl prts NOTE: If door does not hve utout for ling inside lok

More information

Operation Manual. Embroidery Machine. Product Code: 882-D80/D82

Operation Manual. Embroidery Machine. Product Code: 882-D80/D82 Opertion Mnul Emroidery Mchine Product Code: 882-D80/D82 Be sure to red this document efore using the mchine. We recommend tht you keep this document nery for future reference. TRADEMARKS IMPORTANT: READ

More information

RWM4400UH High Performance Hand Held Wireless Microphone System

RWM4400UH High Performance Hand Held Wireless Microphone System CH 1 CH 2 CH 3 CH 4 UHF QUAD VOLUME MAX VOLUME MAX VOLUME MAX VOLUME RWM 4400UH MIN MIN MIN CHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4 RWM4400UH High Performne Hnd Held Wireless Mirophone System OWNER S MANUAL

More information

POWER TRIM. Table of Contents. Section 5C - Dual Power Trim System

POWER TRIM. Table of Contents. Section 5C - Dual Power Trim System SERVICE MANUAL NUMBER 28 Tle of Contents POWER TRIM Setion 5C - Dul Power Trim System DUAL POWER TRIM SYSTEM Lurints / Selnts / Adhesives..... 5C-2 Importnt Informtion................ 5C-2 Testing Dul

More information

All information provided related to future Intel products and plans is preliminary and subject to change at any time, without notice.

All information provided related to future Intel products and plans is preliminary and subject to change at any time, without notice. TRADEMARKS IMPORTANT: READ BEFORE DOWNLOADING, COPYING, INSTALLING OR USING. By downloding, copying, instlling or using the softwre you gree to this license. If you do not gree to this license, do not

More information

INSTALLATION & OPERATION INSTRUCTIONS LEVER HANDLE LOCKSETS.

INSTALLATION & OPERATION INSTRUCTIONS LEVER HANDLE LOCKSETS. INSTALLATION & OPERATION INSTRUCTIONS FOR LEVER HANDLE LOCKSETS 999-00333E_EN FOR BRINKS HOME SECURITY INTERIOR LOCKING & NON-LOCKING LEVER HANDLE LOCKSETS. FITS DOORS 1-3/8" (35 mm) TO 1-3/4" (45 mm)

More information

Basic Embroidery. Chapter 5 COMBINING PATTERNS BEFORE EMBROIDERING PREPARING THE FABRIC SELECTING PATTERNS...

Basic Embroidery. Chapter 5 COMBINING PATTERNS BEFORE EMBROIDERING PREPARING THE FABRIC SELECTING PATTERNS... Chpter 5 Bsic Emroidery BEFORE EMBROIDERING... 196 Emroidery Step y Step...196 Attching Emroidery Foot W+ with LED pointer...197 Attching the Emroidery Unit...197 Aout the Emroidery Unit... 197 Removing

More information

Operation Manual. Embroidery and Sewing Machine. Product Code: 882-C50

Operation Manual. Embroidery and Sewing Machine. Product Code: 882-C50 Opertion Mnul Emroidery nd Sewing Mchine Product Code: 882-C50 Be sure to red this document efore using the mchine. We recommend tht you keep this document nery for future reference. TRADEMARKS IMPORTANT:

More information

McAfee Network Security Platform

McAfee Network Security Platform M-6030 Sensor Quik Strt Guide Revision B MAfee Network Seurity Pltform This Quik Strt Guide explins how to quikly set up nd tivte your MAfee Network Seurity Pltform [formerly MAfee IntruShield ] M-6030

More information

McAfee Network Security Platform

McAfee Network Security Platform M-2750 Sensor Quik Strt Guide Revision B MAfee Network Seurity Pltform This Quik Strt Guide explins how to quikly set up nd tivte your MAfee Network Seurity Pltform M-2750 Sensor in in-line mode. Cling

More information

Patterns and Algebra

Patterns and Algebra Student Book Series D Mthletis Instnt Workooks Copyright Series D Contents Topi Ptterns nd funtions identifying nd reting ptterns skip ounting ompleting nd desriing ptterns numer ptterns in tles growing

More information

ISM-PRO SOFTWARE DIGITAL MICROSCOPE OPERATION MANUAL

ISM-PRO SOFTWARE DIGITAL MICROSCOPE OPERATION MANUAL MN-ISM-PRO-E www.insize.om ISM-PRO SOFTWARE DIGITAL MICROSCOPE OPERATION MANUAL Desription Clik Next. As the following piture: ISM-PRO softwre is for ISM-PM00SA, ISM-PM600SA, ISM- PM60L digitl mirosopes.

More information

Analog Input Modules

Analog Input Modules 7 922 nlog Input odules G56... nlog input modules for the ontrol of SQ5... ir dmper tutors y ontinuous nlog ontrol signls, suh s 4...20 m, nd ontinuous nlog position feedk signls. For supplementry Dt Sheets,

More information

AGA56... Analog Input Modules. Siemens Building Technologies HVAC Products

AGA56... Analog Input Modules. Siemens Building Technologies HVAC Products 7 922 nlog Input odules G56... nlog input modules for the ontrol of SQ5... ir dmper tutors y ontinuous nlog ontrol signls, suh s 4...20 m, nd ontinuous nlog position feedk signls. For supplementry Dt Sheets,

More information

Operation Manual. Addendum. Embroidery Machine. Product Code: 884-T13

Operation Manual. Addendum. Embroidery Machine. Product Code: 884-T13 Emroidery Mchine Opertion Mnul Addendum Product Code: 884-T13 Be sure to red this document efore using the mchine. We recommend tht you keep this document nery for future reference. ABOUT THIS MANUAL ABOUT

More information

Installation manual. Daikin Altherma LAN adapter BRP069A61 BRP069A62. Installation manual Daikin Altherma LAN adapter. English

Installation manual. Daikin Altherma LAN adapter BRP069A61 BRP069A62. Installation manual Daikin Altherma LAN adapter. English Instlltion mnul Dikin Altherm LAN dpter BRP069A6 BRP069A6 Instlltion mnul Dikin Altherm LAN dpter English Tle of ontents Tle of ontents Aout the doumenttion. Aout this doument... Aout the produt. Comptiility....

More information

Abdominal Wound Closure Forceps

Abdominal Wound Closure Forceps Inventor: Crlson, Mrk A. My 25, 2007 Adominl Wound Closure Foreps Astrt. The devie is modifition of stndrd tissue foreps for use during losure of dominl wounds mde for surgil proedure. The modifition onsists

More information

ABOUT THIS MANUAL ABOUT THIS MANUAL

ABOUT THIS MANUAL ABOUT THIS MANUAL ABOUT THIS MANUAL ABOUT THIS MANUAL This mnul provides detils on IQ Designer, which is ville with the upgrde. Mke sure tht the mchine hs een upgrded to the most recent version. When you find this icon

More information

Math Circles Finite Automata Question Sheet 3 (Solutions)

Math Circles Finite Automata Question Sheet 3 (Solutions) Mth Circles Finite Automt Question Sheet 3 (Solutions) Nickols Rollick nrollick@uwterloo.c Novemer 2, 28 Note: These solutions my give you the nswers to ll the prolems, ut they usully won t tell you how

More information

Operation Manual. Embroidery and Sewing Machine. Product Code: 882-C40/C42

Operation Manual. Embroidery and Sewing Machine. Product Code: 882-C40/C42 Opertion Mnul Emroidery nd Sewing Mchine Product Code: 882-C40/C42 Be sure to red this document efore using the mchine. We recommend tht you keep this document nery for future reference. TRADEMARKS IMPORTANT:

More information

Macroscopic and Microscopic Springs Procedure

Macroscopic and Microscopic Springs Procedure Mrosopi nd Mirosopi Springs Proedure OBJECTIVE Purpose In this l you will: investigte the spring-like properties of stright wire, disover the strethiness of mteril, independent of the size nd shpe of n

More information

Operation Manual. Sewing Machine KNOWING YOUR SEWING MACHINE SEWING BASICS UTILITY STITCHES APPENDIX

Operation Manual. Sewing Machine KNOWING YOUR SEWING MACHINE SEWING BASICS UTILITY STITCHES APPENDIX Operation Manual Sewing Machine Product Code: 885-V58/V59/V68/V69 KNOWING YOUR SEWING MACHINE SEWING BASICS UTILITY STITCHES APPENDIX Be sure to read this document before using the machine. We recommend

More information

After opening the box, check that the following accessories are enclosed. If any item is missing or damaged, contact your retailer.

After opening the box, check that the following accessories are enclosed. If any item is missing or damaged, contact your retailer. Enclosed Accessories After opening the box, check that the following accessories are enclosed. If any item is missing or damaged, contact your retailer. Accessories The following items should also be enclosed

More information

WORKSHOP 15 PARASOLID MODELING

WORKSHOP 15 PARASOLID MODELING WORKSHOP 15 PARASOLID MODELING WS15-2 Workshop Ojetives Crete prsoli moel of tension fitting using numer of the prsoli tools in MSC.Ptrn WS15-3 Suggeste Exerise Steps 1. Crete new tse for the tension fitting

More information

1" MORTISE INSTALLATION INSTRUCTIONS

1 MORTISE INSTALLATION INSTRUCTIONS K Aess Control 2941 Indin Avenue Winston-Slem, NC 27105 USA Tel: (800) 849-8324 (336) 725-1331 Fx: (800) 346-9640 (336) 725-3269 www.kess.om www.e-plexlok.om PKG3140 0507 1" MORTISE INSTALLATION INSTRUCTIONS

More information

Fitting & User Instructions

Fitting & User Instructions Issue 03 Alexnder Universl Furniture Risers Note: These frmes require the ddition of n ttchment. (See pges 4 - ) Bse Frme Mrk Bse Frme Mrk Fitting & User Instructions These instructions pply to the rising

More information

ASY P.O. BOX 729 TERRELL, TEXAS / PAGE 1 OF 13 SAM

ASY P.O. BOX 729 TERRELL, TEXAS / PAGE 1 OF 13 SAM 203 Madix Inc., ll rights reserved ommon Parts 2 MXI GRI WIRE GRI SHELF WITH (GPWGS) MXI GRI FIXTURE PNEL (GPWFP) FIXTURE PNELS RE USE S EN SUPPORT. SHELF N E USE NYWHERE. MXI GRI REINFORMENT R 3 (GPR)

More information

After opening the box, check that the following accessories are enclosed. If any item is missing or damaged, contact your retailer.

After opening the box, check that the following accessories are enclosed. If any item is missing or damaged, contact your retailer. Enclosed Accessories After opening the box, check that the following accessories are enclosed. If any item is missing or damaged, contact your retailer. Accessories te (For U.S.A. only) Foot controller:

More information

After opening the box, check that the following accessories are enclosed. If any item is missing or damaged, contact your retailer.

After opening the box, check that the following accessories are enclosed. If any item is missing or damaged, contact your retailer. Enclosed Accessories After opening the box, check that the following accessories are enclosed. If any item is missing or damaged, contact your retailer. Accessories The following items should also be enclosed

More information

Operation Manual. Sewing Machine. Product Code: 888-X53/X54/X55/X56

Operation Manual. Sewing Machine. Product Code: 888-X53/X54/X55/X56 Operation Manual Sewing Machine Product Code: 888-X/X/X/X6 Please visit us at http://solutions.brother.com where you can get product support and answers to frequently asked questions (FAQs). IMPORTANT

More information

Resistors, Current and Voltage measurements, Ohm s law, Kirchhoff s first and second law. Kirchhoff s first Objectives:

Resistors, Current and Voltage measurements, Ohm s law, Kirchhoff s first and second law. Kirchhoff s first Objectives: EE -050 Ciruit L Experiment # esistors, Current nd Voltge mesurements, Ohm s lw, Kirhhoff s first nd seond lw. Kirhhoff s first Ojetives: Slmn in Adul Aziz University Eletril Engineering Deprtment. Fmiliriztion

More information

Operation Manual. Embroidery and Sewing Machine. Product Code: 882-W20/W22

Operation Manual. Embroidery and Sewing Machine. Product Code: 882-W20/W22 Opertion Mnul Emroidery nd Sewing Mchine Product Code: 882-W20/W22 Be sure to red this document efore using the mchine. We recommend tht you keep this document nery for future reference. INTRODUCTION

More information

S2_BrotherE_cover DIC181p K. ENGLISH 885-S06 XC Printed in China

S2_BrotherE_cover DIC181p K. ENGLISH 885-S06 XC Printed in China S_BrotherE_cover DIC8p K ENGLISH 885-S06 XC57-0 Printed in China S_brotherE_Cover.fm Page A Tuesday, March 0, 00 :6 PM Enclosed Accessories After opening the box, check that the following accessories are

More information

SLOVAK UNIVERSITY OF TECHNOLOGY Faculty of Material Science and Technology in Trnava. ELECTRICAL ENGINEERING AND ELECTRONICS Laboratory exercises

SLOVAK UNIVERSITY OF TECHNOLOGY Faculty of Material Science and Technology in Trnava. ELECTRICAL ENGINEERING AND ELECTRONICS Laboratory exercises SLOVAK UNIVERSITY OF TECHNOLOGY Fulty of Mteril Siene nd Tehnology in Trnv ELECTRICAL ENGINEERING AND ELECTRONICS Lbortory exerises Róbert Riedlmjer TRNAVA 00 ELECTRICAL ENGINEERING AND ELECTRONICS Lbortory

More information

McAfee Network Security Platform

McAfee Network Security Platform NS9300XC Sensor Quik Strt Guide Revision A MAfee Network Seurity Pltform This Quik Strt Guide explins how to quikly set up nd tivte your MAfee Network Seurity Pltform NS9300XC Sensor to e lod lned y MAfee

More information

S3_BrotherE_cover DIC181p K. English 885-S08 XC Printed in China

S3_BrotherE_cover DIC181p K. English 885-S08 XC Printed in China S_BrotherE_cover DIC8p K English 885-S08 XC55-0 Printed in China S_brotherE.book Page A Wednesday, February, 00 :9 AM Enclosed Accessories After opening the box, check that the following accessories are

More information

LORING THE SMARTER WAY TO ROAST PROPRIETARY ITEM:

LORING THE SMARTER WAY TO ROAST PROPRIETARY ITEM: TLE, MXIMUM WEIGHTS, L (KG) ROSTER (9) JOS TUING + (9.) GREEN EN RT + (.) EXHUST STK VENT UTO HOPPER.9.. 9.. ZONE TRIER UTO ISHRGE OOR PPROVE J HUTTON. 0....0 9. WLL TO. 0..0 0. REOMMENE LERNE.0. REOMMENE

More information

English Printed in Taiwan XG

English Printed in Taiwan XG COVER 1-4 C M Y K English Printed in Tiwn XG0091-001 Congrtultions on choosing our product! Thnk you very much for purchsing our product. To otin the est performnce from this device nd to ensure sfe nd

More information

CAUTION- SAVE THESE INSTRUCTIONS This product is for household use, or equivalent.

CAUTION- SAVE THESE INSTRUCTIONS This product is for household use, or equivalent. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, dropped into water. Return this sewing machine to the nearest authorized

More information

Elettra Evolution OK! OK! b. User manual

Elettra Evolution OK! OK! b. User manual Elettr Evolution User mnul Pg. 1 INSTALLING THE SOLENOID VALVE. The progrmmle solenoi vlve is fully wtertight n will funtion even if instlle permnently uner wter t epth of up to one metre (IP68 ingress

More information

LORING THE SMARTER WAY TO ROAST PROPRIETARY ITEM:

LORING THE SMARTER WAY TO ROAST PROPRIETARY ITEM: TLE, MXIMUM WEIGHTS, L (KG) ROSTER (.) JOS TUING +. (.) ZONE.. 9.. 0.. 9. WLL TO L 0F STK 9.9 MINIMUM ROSTER LERNES R9.. ELETRIL ENLOSURE OOR OPENING EXHUST VENT JOS TUING EN ISION HISTORY ESRIPTION INITIL

More information

1/4" Multi-Turn Fully Sealed Container Cermet Trimmer

1/4 Multi-Turn Fully Sealed Container Cermet Trimmer www.vishy.om Vishy Sfernie 1/4" Multi-Turn Fully Seled Continer Cermet Trimmer Due to their squre shpe nd smll size (6.8 mm x 6.8 mm x 5 mm), the multi-turn trimmers of the series re idelly suited for

More information

XL5050us_cover. Operation Manual. English XC Printed in China. XC XL5050 (NA03J061) Bk

XL5050us_cover. Operation Manual. English XC Printed in China. XC XL5050 (NA03J061) Bk XL00us_cover Operation Manual English 88-8 XC67-0 Printed in China XC67-0 XL00 (NA0J06) Bk XL000us.book Page Tuesday, November, 00 9: AM IMPORTANT SAFETY INSTRUCTIONS When using this machine, basic safety

More information

660 Freestyle/Style Door with Double In-Line Panels

660 Freestyle/Style Door with Double In-Line Panels 660 Freestyle/Style Door with Doule In-Line Pnels (CUH or MG) Style Series Option M Metl HK87 Slide MGNTIC PULL HNDL KIT with Mgnet Vinyl 989 MGNTIC DOOR STOP 716 HDR / SILL INSRT O V678 VINYL DOOR SL

More information

DCM Series DC T-Series Non-Spring Return Rotary Electronic Damper Actuators

DCM Series DC T-Series Non-Spring Return Rotary Electronic Damper Actuators DCM-0 Series DC-0-T-Series Non-Spring Return Rotry Eletroni Dmper Atutors. Atutor. U-olt shft pter. Position initor EA0R e f g. Shft pter loking lip e. Position initor pter f. Mounting rket g. Mounting

More information

Aluminium Roof Outlets - Introduction to Detail Outlets

Aluminium Roof Outlets - Introduction to Detail Outlets Aluminium Roof Outlets - Introution to Detil Outlets The Hrmer Roof Detil rnge inlues outlets to over ll the wkwr etiling situtions tht our in uiling esign n in refurishment. Min Chrteristis Hrmer Roof

More information

Probability and Statistics P(A) Mathletics Instant Workbooks. Copyright

Probability and Statistics P(A) Mathletics Instant Workbooks. Copyright Proility nd Sttistis Student Book - Series K- P(A) Mthletis Instnt Workooks Copyright Student Book - Series K Contents Topis Topi - Review of simple proility Topi - Tree digrms Topi - Proility trees Topi

More information

Student Book SERIES. Fractions. Name

Student Book SERIES. Fractions. Name D Student Book Nme Series D Contents Topic Introducing frctions (pp. ) modelling frctions frctions of collection compring nd ordering frctions frction ingo pply Dte completed / / / / / / / / Topic Types

More information

BACK DOOR GLASS REPLACEMENT HINT:

BACK DOOR GLASS REPLACEMENT HINT: WINSHIEL/WINOWGLSS/MIRROR REPLEMENT 7025 The instlltion proeures re the removl proeures in reverse orer. However, only instlltion proeures requiring itionl inormtion re inlue. 700VX01 Pino Wire lip 1.

More information

1/4" Multi-Turn Fully Sealed Container Cermet Trimmer

1/4 Multi-Turn Fully Sealed Container Cermet Trimmer 1/4" Multi-Turn Fully Seled Continer Cermet Trimmer Due to their squre shpe nd smll size (6.8 mm x 6.8 mm x 5 mm), the multi-turn trimmers of the series re idelly suited for PCB use, enling high density

More information

Technical Note 7. General Introduction. Holy Stone

Technical Note 7. General Introduction. Holy Stone Generl Introdution Tehnil Note 7 The Multilyer Cermi Chip Cpitors supplied in bulk, ssette or tped & reel pkge re idelly suitble for thik-film Hybrid iruits nd utomti surfe mounting on printed iruit bords.

More information

The Math Learning Center PO Box 12929, Salem, Oregon Math Learning Center

The Math Learning Center PO Box 12929, Salem, Oregon Math Learning Center Resource Overview Quntile Mesure: Skill or Concept: 300Q Model the concept of ddition for sums to 10. (QT N 36) Model the concept of sutrction using numers less thn or equl to 10. (QT N 37) Write ddition

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS Multi Line 6 x8 255x193x203cm / 100 1 /2 x76 x80 Poly-Tex, Inc. PO Box 458 27725 Dnville Avenue Cstle Rock, MN 55010 We Site: www.poly-tex.com English - 69717 Hoy Greenhouse Service

More information

peyote stitch projects and patterns

peyote stitch projects and patterns 6 peyote stith projets nd ptterns 2011 Klmh Pulishing Co. This mteril my not e reprodued in ny form without permission from the pulisher. 1 Contents Colorful onnetions...p. 3 Wve ring...p. 5 Lovely nd

More information

3/8" Square Multi-Turn Cermet Trimmer

3/8 Square Multi-Turn Cermet Trimmer www.vishy.om 3/8" Squre Multi-Turn Cermet Trimmer Vishy Sfernie ermet element. FEATURES Industril grde The is smll size trimmer - 3/8" x 3/8" x 3/16" - nswering PC ord mounting requirements. Five versions

More information

Introduction 6 Basics 8 Projects 26. Stitching terms 94. About the author 95

Introduction 6 Basics 8 Projects 26. Stitching terms 94. About the author 95 Contents Klmh Books 21027 Crossros Cirle Wukesh, Wisonsin 53186 www.klmh.om/books 2010 Lesley Weiss All rights reserve. Exept for rief exerpts for review, this ook my not e reproue in prt or in whole y

More information

MAIN PARTS

MAIN PARTS MAIN PARTS 7 8 9 10 11 12 13 1 2 3 17 4 5 6 01 02 03 04 05 12 23 34 45 56 13 24 35 46 57 14 25 36 47 58 15 16 26 27 37 38 48 49 59 60 06 07 08 09 10 17 18 28 29 39 40 50 51 61 62 19 30 41 52 63 20 21 31

More information

3/8" Square Multi-Turn Cermet Trimmer

3/8 Square Multi-Turn Cermet Trimmer Vishy Sfernie 3/8" Squre Multi-Turn Cermet Trimmer FEATURES Industril grde W t 70 C The T93 is smll size trimmer - 3/8" x 3/8" x 3/16" - nswering PC ord mounting requirements. Five versions re ville whih

More information

mac profile Configuration Guide Adobe Photoshop CS/CC Sawgrass Virtuoso SG400/SG800 Macintosh v

mac profile Configuration Guide Adobe Photoshop CS/CC Sawgrass Virtuoso SG400/SG800 Macintosh v mc profile Mcintosh 10.5-10.10 Configurtion Guide Adoe Photoshop CS/CC Swgrss Virtuoso SG400/SG800 v20150427 Configurtion Guide - Photoshop CS/CC Swgrss SG400/800 Before proceeding, ensure the correct

More information

When using an electrical appliance, basic safety precautions should always be followed, including the following:

When using an electrical appliance, basic safety precautions should always be followed, including the following: Instruction book IMPORTANT SAFETY INSTRUCTIONS This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge,

More information

(1) Primary Trigonometric Ratios (SOH CAH TOA): Given a right triangle OPQ with acute angle, we have the following trig ratios: ADJ

(1) Primary Trigonometric Ratios (SOH CAH TOA): Given a right triangle OPQ with acute angle, we have the following trig ratios: ADJ Tringles nd Trigonometry Prepred y: S diyy Hendrikson Nme: Dte: Suppose we were sked to solve the following tringles: Notie tht eh tringle hs missing informtion, whih inludes side lengths nd ngles. When

More information

Pearson Education Limited Edinburgh Gate Harlow Essex CM20 2JE England and Associated Companies throughout the world

Pearson Education Limited Edinburgh Gate Harlow Essex CM20 2JE England and Associated Companies throughout the world Person Edution Limited Edinurgh Gte Hrlow Essex M20 2JE Englnd nd ssoited ompnies throughout the world Visit us on the World Wide We t: www.personed.o.uk Person Edution Limited 2014 ll rights reserved.

More information

LEXUS IS250/IS350 FRONT SPOILER Section I - Installation Preparation. Part Number: Section I - Installation Preparation.

LEXUS IS250/IS350 FRONT SPOILER Section I - Installation Preparation. Part Number: Section I - Installation Preparation. Section I - Instlltion Preprtion Prt Numer: 0854-53830 Section I - Instlltion Preprtion Kit Contents 3 Description Front spoiler Hrdwre g Instruction mnul Additionl Items Required For Instlltion Conflicts

More information

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS When using this machine, basic safety precautions should always be taken, including the following: Read all instructions before using. DANGER To reduce the risk of electric

More information

Aquauno Select MINUTES. (duration) FREQUENCY LED. OFF 8h AQUAUNO SELECT 5 MIN FREQUENCY. the timer is being programmed;

Aquauno Select MINUTES. (duration) FREQUENCY LED. OFF 8h AQUAUNO SELECT 5 MIN FREQUENCY. the timer is being programmed; Aquuno Select Pg. INSTALLATION. Attch the timer to cold wter tp, following these simple instructions. Do not instll the timer in pit or vlve ox, elow ground level or indoors. Do not use the timer with

More information

Programming Guide. Neurostimulators for Chronic Pain. RestoreSensor, RestoreUltra, RestoreAdvanced, and PrimeAdvanced

Programming Guide. Neurostimulators for Chronic Pain. RestoreSensor, RestoreUltra, RestoreAdvanced, and PrimeAdvanced Progrmming Guide Neurostimultors for Chroni Pin RestoreSensor, RestoreUltr, RestoreAdvned, nd PrimeAdvned For use with SureSn MRI nd erlier non-suresn Neurostimultion Systems. Overview This guide desries

More information

PROGRAMMING MANUAL MTMA/01 MTMV/01 FB00329-EN

PROGRAMMING MANUAL MTMA/01 MTMV/01 FB00329-EN RMMING MNUL MTM/01 MTMV/01 FB00329-EN Generl precutions Red the instructions crefully efore eginning the instlltion nd crry out the ctions s specified y the mnufcturer. The instlltion, progrmming, commissioning

More information

REMOTE IR/LED MODULE REMOTE 3 REVISION HISTORY C DETAIL A SCALE 1 : 1.5 I\O PANEL - SHEET 1 OF 6 ECO ZONE REV. DESCRIPTION DATE APPR'D

REMOTE IR/LED MODULE REMOTE 3 REVISION HISTORY C DETAIL A SCALE 1 : 1.5 I\O PANEL - SHEET 1 OF 6 ECO ZONE REV. DESCRIPTION DATE APPR'D 00000 ISION HISTORY EO ZONE. ESRIPTION TE PPR'. 9...0 IR 0 0.. LE INITOR LNSPE WLL MOUNT HNGERS REMOTE IR/LE MOULE REMOTE. 0 PORTRIT WLL MOUNT HNGERS SERVIE PNEL KEEP PERFORTE RES LER FOR IRFLOW. 9..0..

More information

Section 6.1 Law of Sines. Notes. Oblique Triangles - triangles that have no right angles. A c. A is acute. A is obtuse

Section 6.1 Law of Sines. Notes. Oblique Triangles - triangles that have no right angles. A c. A is acute. A is obtuse Setion 6.1 Lw of Sines Notes. Olique Tringles - tringles tht hve no right ngles h is ute h is otuse Lw of Sines - If is tringle with sides,, nd, then sin = sin = sin or sin = sin = sin The miguous se (SS)

More information

SAVE THESE INSTRUCTIONS

SAVE THESE INSTRUCTIONS INSTRUCTION BOOK IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the followings: Read all instructions before using this

More information

Question Paper Wednesday 13 Thursday 14 January 2010

Question Paper Wednesday 13 Thursday 14 January 2010 KEY SKILLS INFORMATION AND COMMUNICATION TECHNOLOGY Level 3 ArtComp [KSI31] Question Pper Wenesy 13 Thursy 14 Jnury 2010 Do NOT open this Question Pper until you re tol to y the invigiltor THERE ARE THREE

More information

* * 33/3549A CS 33/3549A. 2-Point Latch includes these additional parts. 1-Point Latch (LBL) Customer Service. Installation Instructions

* * 33/3549A CS 33/3549A. 2-Point Latch includes these additional parts. 1-Point Latch (LBL) Customer Service. Installation Instructions *23970726* 23970726 33/3549A CS 33/3549A Instlltion Instructions This instruction covers new instlltion of the 33/3549A conceled verticl device for luminum nd hollow metl doors. RF Also covered is the

More information

11210 INSTRUCTION MANUAL

11210 INSTRUCTION MANUAL 11210 INSTRUCTION MANUAL Important Safety Instructions When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using

More information

Tubing Spacers. Backing Plate. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a a. a a. a a

Tubing Spacers. Backing Plate. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a a. a a. a a Grnd Slm Instlltion Instructions TACO Metls Inc., 98 NE 179th Street Mimi, Florid 33162 hndyhnk@tcomrine.com tcomrine.com This Box Contins: 1- Port side Grnd Slm 1- Strbord side Grnd Slm 4-5/16 x 1 stinless

More information