Introduction to Soldering Electronic Circuits
|
|
- Fay Collins
- 5 years ago
- Views:
Transcription
1 Introduction to Soldering Electronic Circuits Department of Electrical and Computer Engineering Kettering University Soldering Tools and Supplies Good quality pencil-type soldering iron Small gauge resign core solder Damp sponge Safety glasses Needle nose pliers/wire cutters Bench top vise for extra hands Braided de-soldering wick
2 Soldering Safety Always wear safety glasses Solder on a fire resistant surface (never directly on a bench or desk top) Never leave a hot iron unattended Use caution when laying down or picking up a hot iron (tip temperatures are degrees F) Use a soldering iron stand if available Replace the cord if it becomes worn or burnt Do not overload electrical outlets A clean tip is important A clean tip assures good thermal contact between iron and component Clean the tip regularly by wiping on a damp sponge
3 Holding the soldering iron Hold the soldering iron in a relaxed position, like holding a pen Steady your arm by resting it on the work surface Correct component placement Place the components through the holes on the top side of board Check the alignment of polarized components Components should be nearly flush with the board surface Bend the leads outward on the bottom side to hold components in place while soldering
4 Incorrect component placement Here the components are not placed flush with the board surface See the previous slide for correct, flush component placement Tin the tip Melt a small amount of solder on the tip before beginning; called tinning the tip This procedure reduces oxidation on the tip and improves heat transfer to the component
5 Soldering technique The component lead should be between the iron and the solder Heat the component lead and the PCB trace for a short time (max. 2-3 seconds) Touch the solder to the component lead (not the tip of the iron) Soldering technique (cont.) Feed a small amount of molten solder to the joint Some solder will be drawn up into hole, the rest will form a cone around the lead Pull the solder away first, then pull the iron away
6 Good solder joint A good solder joint should be shiny and cone shaped Wiggle the component slightly to test for good mechanical connection Trim the excess lead length with wire cutters Bad solder joint A bad (cold) solder joint will be dull and glob-like The board may be discolored from overheating These symptoms will lead to unreliable electrical and mechanical connection
7 De-soldering If you make a mistake, solder can be removed from a connection using braided desoldering wick De-soldering Place the braided desoldering wick on the solder to be removed Heat the wick to melt and draw the solder into the wick Continue to use fresh wick until all solder is removed and component lead is free
8 Completed board This is an example of the top side of a completed board Components are neatly aligned with correct polarity and placed flush with the board surface Completed board This is an example of the bottom side of a completed board Solder joints are shiny and cone shaped Board is not discolored from over-heating Excess leads are neatly trimmed off There are no unwanted solder bridges between connections
9 Finishing Up Before finishing, invest some time in checking over your work. It could save you hours of trouble-shooting and re-work later. Look for solder bridges between connections, cold solder joints, missed connections, and reversed polarity on components. Touch up any solder connections that seem less than perfect. Once power is applied.it may be too late!
Soldering & De-soldering
Soldering and De-soldering Digital Electronics 04 Soldering & De-soldering This presentation will Review the tools needed to solder and de-solder electronic components. Demonstrate how to tin a soldering
More informationSoldering Techniques NIAGARA COLLEGE TECHNOLOGY DEPT.
Soldering Techniques NIAGARA COLLEGE TECHNOLOGY DEPT. Soldering 101 Soldering is the process of joining two metals together to form an electrically ll and mechanically secure bond using heat and a third
More informationIntroduction to Soldering
Introduction to Soldering The Soldering Iron American Standard Wire Gage (AWG) Solder The Soldering Process Stripping & Tinning Wire Connecting/Soldering Wire Component Soldering De-Soldering Lab Exercise
More informationSOLDERING MANUAL A simple, yet easy to follow manual for your basic soldering needs. Copyright 2017 TortugaPro. All Rights Reserved
A simple, yet easy to follow manual for your basic soldering needs Copyright 2017 TortugaPro. All Rights Reserved Purpose Soldering is not limited to electrical and electronics work. It is a skill that
More informationXkitz.com XLO-5CP Control Panel for Five Channel Color Light Organ
Xkitz.com XLO-5CP Control Panel for Five Channel Color Light Organ Rev 1.15 An Optional accessory for the Xkitz XLO-5 or XLO-5DC 5 Channel Color Light Organs Introduction This kit contains all the electronics
More informationElectronics Merit Badge Class 4. 12/30/2010 Electronics Merit Badge Class 4 1
Electronics Merit Badge Class 4 12/30/2010 Electronics Merit Badge Class 4 1 Soldering Safety Note: A Soldering Iron gets hotter than 374 F. Do not touch the soldering iron s metal parts or you will receive
More informationupad Proto Base Assembly Guide v2.0
upad Proto Base Assembly Guide v2.0 Last Updated September 1, 2015 Table of Contents Preface... 3 Introduction... 3 Required Tools... 3 Flux Pen... 3 Soldering Iron... 3 Solder... 3 Diagonal Cutters...
More informationAny Questions? Contact us or BSA Atomic Blinkie
BSA Atomic Blinkie The heart of this blinkie is a tiny electronic chip embedded in each of the three LEDs. When power is applied, the chip tells the LED to turn on and off, or fade different colors By
More information01. Parts. Blink v1.1. Battery Holder x1. Red LED x1 Green LED x1 Blue LED x1. Resistors x3. Battery x1. Blink PCB x1. Push Button Switchers x3
Blink L1 L2 L3 01. Parts Battery Holder x1 Red LED x1 Green LED x1 Blue LED x1 Resistors x3 Learn to Solder Kit Battery x1 L1 L2 L3 Blink PCB x1 S3 Push Button Switchers x3 02. Tools RECOMENDED Soldering
More informationCornerstone Electronics Technology and Robotics I Week 19 Soldering Tutorial
Cornerstone Electronics Technology and Robotics I Week 19 Soldering Tutorial Administration: o Prayer o Turn in quiz o Using fixed resistors design and build a voltage divider divides 5 volts in half.
More informationElectrical Workshop. Module 6: Soldering Techniques. Academic Services Unit PREPARED BY. August 2012
Electrical Workshop PREPARED BY Academic Services Unit August 2012 Applied Technology High Schools, 2012 Module Objectives Upon successful completion of this module, students should be able to: 1. Identify
More informationLearn to solder electronics with the Maker
Learn to solder electronics with the Maker Shed Solder Badge! How to assemble the Maker Shed Badge kit. Written By: Alexander ifixit CC BY-NC-SA www.ifixit.com Page 1 of 19 INTRODUCTION The Maker Shed
More informationEE 1202 Labs: Ground Rules
EE 1202 Labs: Ground Rules There are eight lab exercises that you will do as a part of EE 1202. The EE 1202 lab is ECSS 4.622, on the third floor of the ECSS building. Lab exercises will be done by teams
More informationELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS Lesson 13 EET 150 Electrical Connections Learning Objectives In this lesson you will: see different methods of making electrical connections. learn a procedure for making soldered
More informationLighthouse Beginner s soldering kit
Lighthouse Beginner s soldering kit Kit contains: 1 x 220 ohm resistor (Red, Red, Black) 1 x 82k ohm resistor (Grey, Red, Orange) 2 x 220k ohm resistors (Red, Red, Yellow) 2 x Diodes 1 x Power switch 1
More informationSoldering and Desoldering Instruction
Soldering and Desoldering Instruction Soldering is defined as "the joining of metals by a fusion of alloys which have relatively low melting points". In other words, you use a metal that has a low melting
More informationSoldering is easy. here's how to do it. Andie Nordgren (Comics adaptation) Jeff Keyzer. by: Mitch Altman (soldering wisdom) (Layout and editing)
Soldering is easy here's how to do it by: Mitch Altman (soldering wisdom) Andie Nordgren (Comics adaptation) Jeff Keyzer (Layout and editing) Download this comic book and share it with your friends! Distribute
More informationExperiment 2 Soldering Parallel and Series Circuits and using the Digital Multimeter
Experiment 2 Soldering Parallel and Series Circuits and using the Digital Multimeter Introduction Soldering is the most common means of joining components to each other or to circuit boards in electronics.
More information01. Parts. LEDs x2. On/Off Switch x1. Jitterbug PCB x1. Vibration Motor x1. Battery Holder x1. Wire x1. 3V Coin Cell Battery x1
01. Parts LEDs x2 Jitterbug PCB x1 On/Off Switch x1 Vibration Motor x1 Battery Holder x1 Wire x1 3V Coin Cell Battery x1 02. Tools RECOMENDED Soldering Iron 110V 60W Soldering Iron FINE SOLDER WIRE Flush
More informationTechnical Specifications - Characteristics
Watt FM TRANSMITTER General Description This is a small but quite powerful FM transmitter having three RF stages incorporating an audio preamplifier for better modulation. t has an output power of 4 Watts
More informationTips For Soldering. By Harsh Tandel. Team Blip EEC 134A/B, Introduction
Tips For Soldering By Harsh Tandel 914346151 Team Blip EEC 134A/B, 2017-2018 Introduction Every electrical engineer should at least know the basic soldering skills. It is very important to be familiar
More informationGENERAL SOLDERING PROCEDURE
College of Engineering Laboratory Procedure GENERAL SOLDERING PROCEDURE Dept: Multi-department Laboratory: Multi-lab Rm: Multi-lab Authored by: Dick Sevier, Lab Support Engineer Date: Reviewed and Approved
More informationSolder is a metallic glue that holds the parts together and forms a connection that allows electrical current to flow.
Proper Soldering & Desoldering High Performance Ultrasonic Range Finders Techniques of a MaxBotix Sensor Materials Needed for Soldering Goggles Hands-free clamp Wire stripper Soldering iron with stand
More informationUser s Manual SOLDERING STATION
User s Manual SOLDERING STATION ASE-1111 Thank you for choosing AKTAKOM soldering station. www.tmatlantic.com Please note the following safety notes to avoid malfunctions, damage or physical injury: Persons
More informationBetter Soldering (A COOPER Tools Reprint) Overview Solder and Flux Base Material
Better Soldering (A COOPER Tools Reprint) Purpose We hope this short manual will help explain the basics of Soldering. The emphasis will be on the care and use of equipment. Overview Soldering is accomplished
More informationSoldering Basics. Purpose We hope this short manual will help explain the basics of Soldering. The emphasis will be on the care and use of equipment.
Soldering Basics Purpose We hope this short manual will help explain the basics of Soldering. The emphasis will be on the care and use of equipment. Overview Soldering is accomplished by quickly heating
More informationOpenROV. Guide 3 - Electronics. We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV
OpenROV Guide 3 - Electronics We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV 2017 openrov.dozuki.com Page 1 of 33 INTRODUCTION We will introduce soldering
More informationSolder Practice Kit MODEL AK-100. Elenco Electronics, Inc. Lesson Manual. Elenco Electronics, Inc.
Solder Practice Kit MODEL AK-100 Elenco Electronics, Inc. 150 W. Carpenter Avenue Wheeling, IL 60090 (847) 541-3800 http://www.elenco.com e-mail: elenco@elenco.com Lesson Manual Elenco Electronics, Inc.
More informationLesson 2: Soldering. Goals
Introduction: Its time to learn how to solder. So you have met all the components needed to make a DIY Gamer, now it s time to put it together. Soldering is joining the components to the printed circuit
More informationRepairing your Porsche 928 Central Warning System (CWS) controller
Repairing your Porsche 928 Central Warning System (CWS) controller Disclaimer: This procedure is for a 1984 Porsche 928 S controller. Overview: Under the left foot pedal (dead pedal) of the Porsche 928
More informationQUASAR ELECTRONICS KIT No DRILL SPEED CONTROLLER
QUASAR ELECTRONICS KIT No. 1074 DRILL SPEED CONTROLLER General Description If you work with an electric drill and unless you are lucky enough to own one of the most sophisticated models with speed control,
More informationLEARN TO SOLDER CLASS PACK
TEACHING RESOURCES HOW TO SOLDER GUIDE BUILD INSTRUCIONS HOW THE KIT WORKS DEVELOP YOUR SOLDERING SKILLS WITH THIS LEARN TO SOLDER CLASS PACK Version 1.0 Index of Sheets Introduction... 3 Answers... 4
More informationLesson 2: Soldering. Goals
Introduction: Its time to learn how to solder. So you have met all the components needed to make a DIY Gamer, now it s time to put it together. Soldering is joining the components to the printed circuit
More informationPacific Antenna Easy TR Switch
Pacific Antenna Easy TR Switch Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate receiver
More informationHow to Hand Solder an Electric Wire to a COB LED
How to Hand Solder an Electric Wire to a COB LED Table of Contents 1. Overview 2. Necessary/Recommended Soldering Equipment 3. How to Choose the Optimal Soldering Iron Tip 4. Cautions/Suggestions for Stripping
More informationPacific Antenna - Easy TR Switch
Pacific Antenna - Easy TR Switch Kit Description The Easy TR Switch is an RF sensing switch that can be used to switch an antenna between a receiver and transmitter. It also has a second switched pair
More informationTips in Soldering. By Jesus Beltran. Team J (AKA J Crew) EEC 134AB, Professor Xiaoguang Liu UC Davis College of Engineering
Tips in Soldering By Jesus Beltran Team J (AKA J Crew) EEC 134AB, 2015 16 Professor Xiaoguang Liu UC Davis College of Engineering INTRODUCTION Basic soldering skills is a trait that every electronic/electrical
More informationEasy Transmitter. Support ETX_REV5_Manual V2.7 Revised
Easy Transmitter Introduction The Easy Transmitter kit from qrpkits.com provides a basic, crystal controlled transmitter with VXO tuning to provide a small tuning range around the crystal frequency. It
More informationLearn to Solder: Simon Says Stencil Kit Information & Instructions
Learn to Solder: Simon Says Stencil Kit Information & Instructions This is considered an intermediate kit for people who have soldered through-hole components before and wish to learn how to reflow surface
More informationEET 150 Introduction to EET Lab Activity 6 Introduction to Wire Splicing and Soldering
Required Parts, Software and Equipment Parts None for this activity EET 150 Equipment Required Hookup wire (22 AWG) Wire cutter/stripper Soldering Iron* Soldering Iron Stand* Solder (Use standard lead/tin
More informationKey Tips & Techniques for Taking Care of Solder Iron Tips
Key Tips & Techniques for Taking Care of Solder Iron Tips 1 Tip Construction Copper Core Iron Plating Nickel plating over the Iron Chrome plating over the nickel Tin over Chrome plating 2 What is in a
More informationPacific Antenna Easy SWR Indicator Kit
Pacific Antenna Easy SWR Indicator Kit Description Monitoring the match of an antenna to your transmitter or adjusting an antenna tuner for best match requires an indicator of the reflected power as an
More informationFM Wireless Microphone Kit Instructions for Assembly Page 1 of 5
Instructions for Assembly Page 1 of 5 1. Find Resistor R1. Remove any tape that may be attached to the leads. Bend the leads as needed to insert Resistor R1 into the printed circuit board in the holes
More informationFirefly Jar Learn to Solder Kit
Firefly Jar Learn to Solder Kit Parts Tools A. Firefly Jar PCB B. 10mm Flickering LED (White or Yellow) C. Resistor D. Tilt Switch (Black or Green) E. Battery Holder F. Velcro ( Not Pictured) G. Jar (
More informationTHE TRILL TREMOLO (K-960)
THE TRILL TREMOLO (K-60) DEPTH SPEED The Trill Tremolo Modkitsdiy.com Unplug when not in use to save battery life. TO AMP IN FROM GUITAR OUT Use these instructions to learn: How to build an effects pedal
More informationValue Location Qty Potentiometers C1M Distortion 1 A10k Volume 1. Footswitch 3PDT SW1 1. Jacks 1/4 Mono 2 DC Power 1
Distortion BUILD INSTRUCTIONS Thank you for your purchase of our Distortion+ kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same
More informationAny Questions? Contact us or Alligator Blinkie
Alligator Blinkie The heart of this blinkie is a 12F1822 PIC produced by a company called Microchip. A PIC is a tiny, yet surprisingly powerful little computer. By itself, it can t do much it needs someway
More informationTHE AGGRESSOR (K-995)
THE AGGRESSOR (K-99) TONE VOLUME DISTORTION MID-SHIFT SWITCH LED The Aggressor Distortion Pedal Modkitsdiy.com 9 VDC CENTER (-) ADAPTER TO AMP IN FROM GUITAR OUT Unplug when not in use to save battery
More informationπλ² Synthesizer Manual for Assembly Kit Features 2 Oscillators 4 Waveforms 32 Presets 32 User presets
πλ² Synthesizer Manual for Assembly Kit Features 2 Oscillators 4 Waveforms 32 Presets 32 User presets Specifications Power supply: +5V DC/50mA Dimensions: 100 x 100 x 23mm Congratulations on purchasing
More informationDuoDrive Nixie Bargraph Kit
Assembly Instructions And User Guide Nixie Bargraph Kit - 1 - REVISION HISTORY Issue Date Reason for Issue Number 1 12 December 2017 New document - 2 - 1. INTRODUCTION 1.1 About Nixie Bargraph Driver IN-9
More informationW7MRI's Anderson Powerpole. Power Hub
W7MRI's Anderson Powerpole Power Hub This PDF is provided by K7JM at http://radio.mcdougallshome.net Don, W7MRI made up a nice small circuit board that holds 7 pairs of Anderson Powerpole connectors to
More informationA Precision 2000 Mixed Media Project
Día de los Muertos (Day of the Dead) Panel A Precision 2000 Mixed Media Project PROJECT TITLE: Día de los Muertos (Day of the Dead) Panel DESIGNED BY: Andy Spencer SKILL LEVEL: (Adult 1-5: 1 being the
More informationTemperature activated switch
Build instructions, circuit explanation and example applications Issue 1.5 Product information: www.kitronik.co.uk/quicklinks/2113/ TEACHER Temperature activated switch Introduction About the project kit
More informationAssembly Instructions for the 1.5 Watt Amplifier Kit
Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are
More informationTelecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering tips: Removing Current Wiring: Step 1. Step 2.
Telecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers Wire Strippers 3/8 Drill Bit 5/32 Drill Bit
More informationPacific Antenna Easy Transmitter Kit
Pacific Antenna Easy Transmitter Kit Introduction The Easy Transmitter kit from qrpkits.com provides a crystal controlled transmitter with VXO tuning. The circuit consists of a N3904 based crystal oscillator
More informationConstruction Hints and Techniques
Construction Hints and Techniques You just get finished building a Microwave project and it looks beautiful. After admiring it for awhile you decide to spark it up. All of the voltages and currents look
More informationTHE THUNDERDRIVE (K-950)
THE THUNDERDRIVE (K-950) OUTPUT DISTORTION Unplug when not in use to save battery life. TO AMP IN The Thunderdrive Modkitsdiy.com FROM GUITAR OUT Use these instructions to learn: How to build an effects
More informationGat ew ay T o S pace AS EN / AS TR Class # 07. Colorado S pace Grant Consortium
Gat ew ay T o S pace AS EN / AS TR 2500 Class # 07 Colorado S pace Grant Consortium One Minute Reports: - Can we have two data loggers? - Do you provide us with cameras? {Hardware Checkout after proposal}
More informationStained Glass Mission-Style Frame A stained glass project
Stained Glass Mission-Style Frame A stained glass project Stained Glass Mission-Style Frame A Stained Glass Project PROJECT TITLE: Stained Glass Mission-Style Frame SKILL LEVEL: (Adult 1-5: 1 being the
More informationExplorer Wiring Kit (assembled)
Explorer Wiring Kit (assembled) For Vintage, Firestorm & Standard Series Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers
More informationRead This Page First
Read This Page First If you are reading this you know the manuals are always available at QRPKITS.com. This is version 8.0 of the manual dated 4/27/2016. There is no need to print out the whole assembly
More informationManual Version July 2007
Manual Version 1.2 - July 2007 Page 1 Table of Contents Section1: M3 Phono Board Build...3 Phono Board Parts List...3 Preparation...4 Fitting the Valve Bases...6 Installing the Resistors...7 Starting the
More informationTotal solder points: Difficulty level: beginner advanced 3 DIGIT PANEL METER KIT K2032 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 65 + 49 Difficulty level: beginner 1 2 3 4 5 advanced 3 DIGIT PANEL METER KIT K2032 Ideal replacement for moving coil meters ILLUSTRATED ASSEMBLY MANUAL H2032IP-1 Features & Specifications
More informationValue Location Qty Transistors 2N5485 Q1, Q2, 4 Q3, Q4 2N5087 Q5 1. Trim Pots 250k VTRIM 1. Potentiometers C500k Speed 1. Toggle Switch On/On Vibe 1
P-90 BUILD INSTRUCTIONS Thank you for your purchase of our P-90 kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same great sound!
More informationWritten By: Christopher Hartigan
Fender Starcaster Pickups Replacement Written By: Christopher Hartigan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION Pickups may become scratchy or unresponsive and may require replacement.
More informationInduction Heater Coil Kit Compact low voltage, high current induction coil
Induction Heater Coil Kit Compact low voltage, high current induction coil Model: CT-400-KIT Features and Specifications High power water cool-able copper coil PCB Layout designed to reduce eddy losses
More informationSurface Mount Rework Techniques
Technical Note Surface Mount Rework Techniques Table of Contents Abstract:...1 Removing Discrete and Passive Components...1 Replacing Discrete Components...2 Removal of SOICS, SOJS, and SOPS...3 Pad Clean
More informationWiring our Micro LEDs CAUTION!
Wiring our Micro LEDs Secure Site Shop with Confidence Best viewed using: Internet Explorer or Mozilla Firefox If you've wired up some of our 2x3 LEDs, you've gained the general techniques required to
More informationiphone 1st Generation Battery Replacement Written By: irobot ifixit CC BY-NC-SA Page 1 of 15
Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 15 INTRODUCTION Battery not lasting long? Swap it out (requires soldering). TOOLS: Probe and Pick Set (1) Desoldering Braid (1) SIM Card Eject
More informationSOLDER PRACTICE KIT MODEL SP-3B. Assembly and Instruction Manual
SOLDER PRACTICE KIT MODEL SP-3B 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Assembly and Instruction Manual Elenco Electronics,
More informationIntroduction. Pictures in this lab have been taken from Pre-Lab Homework
Introduction This lab relates to material in Hecht, Chapter 18. In this lab you will explore the concepts of circuits, resistors, and capacitors, by actually building a small circuit that is yours to keep!
More informationConvert 10M (33 ) 100 LED Sequencing Strings to Full Wave Always On.
Convert 10M (33 ) 100 LED Sequencing Strings to Full Wave Always On. DoItYourselfChristmas.Com User: CaptKirk If you search EBAY, you will find a number of vendors offering 10m 100 LED Fairy Lights. That
More informationSSRP LTC1746 Assembly Manual V0.1 Check the most recent version
SSRP LTC1746 Assembly Manual V0.1 Check the most recent version http://oscar.dcarr.org/ssrp/hardware/ltc1746/ltc1746.php Introduction This manual details the general assembly process for the SSRP LTC1746
More information400W MONO/STEREO AMPLIFIER
400W MONO/STEREO AMPLIFIER Universal, robust and compact are the words to describe this amplifier. Total solder points: 264 Difficulty level: beginner 1 2 3 4 5 advanced K4005B ILLUSTRATED ASSEMBLY MANUAL
More informationRF Current Meter Kit
Kit When assembled, this kit provides you with a simple but effective means of measuring the current in antenna wires, and of looking for braid currents on coax feeders. The more current you can get flowing
More informationTotal solder points: 33 Difficulty level: beginner advanced. 7W mono amplifier K4001 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 33 Difficulty level: beginner 1 2 3 4 5 advanced 7W mono amplifier K4001 Small but powerful multipurpose amplifier. ILLUSTRATED ASSEMBLY MANUAL H4001IP-1 2 Features & Specifications
More informationBuilding the Toothpick Audio CW Filter
Building the Toothpick Audio CW Filter Introduction The toothpick is a simple variable bandpass audio filter designed to compliment the Splinter QRPp Trans-Receiver. The filter also contains an audio amplifier
More informationSOLDERING TO TRANSDUCERS
APPLICATION NOTE AN-13 SOLDERING TO TRANSDUCERS The purpose of this Application Note is to aid the user of Knowles transducers to: Provide good electrical connections to the transducer Avoid undesired
More information2.00AJ / 16.00AJ Exploring Sea, Space, & Earth: Fundamentals of Engineering Design Spring 2009
MIT OpenCourseWare http://ocw.mit.edu 2.00AJ / 16.00AJ Exploring Sea, Space, & Earth: Fundamentals of Engineering Design Spring 2009 For information about citing these materials or our Terms of Use, visit:
More informationHAND SOLDERING FOR THROUGH-HOLE COMPONENTS (DVD-42C) TRAINING CERTIFICATION EXAM v.2
This test consists of thirty multiple-choice questions. All questions are from the video: Hand Soldering for Through-Hole Components (DVD-42C). Each question has only one most correct answer. Circle the
More informationPacific Antenna Low Pass Filter Kit
Pacific Antenna Low Pass Filter Kit Description Many basic transmitter and/or transceiver designs have minimal filtering on their output and frequently have significant harmonic content in their signals.
More informationTHE STEP LADDER (K-978)
THE STEP LADDER (K-978) Footswitch True-bypass = 0 db OUTPUT INPUT Ground shunt switching on the input jack keeps the amp quiet when unplugged from the Step Ladder. Attenuator Pot Full clockwise = 0 db
More informationTotal solder points: 198 Difficulty level: beginner advanced DUAL ELECTRONIC DICE K3400 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 198 Difficulty level: beginner 1 2 3 4 5 advanced DUAL ELECTRONIC DICE K3400 Cheating is no longer possible! ILLUSTRATED ASSEMBLY MANUAL H3400IP-1 Features & Specifications Features:
More informationTHE RING RESONATOR (K-975)
THE RING RESONATOR (K-975) OUTPUT BOOST The Ring Resonator An Octave Up Fuzz Modkitsdiy.com 9 VDC CENTER (-) ADAPTER TO AMP IN FROM GUITAR OUT Unplug when not in use to save battery life. Use these instructions
More informationSOLDER PRACTICE KIT MODEL SP-3B. Assembly and Instruction Manual ELENCO
SOLDER PRACTICE KIT MODEL SP-3B Assembly and Instruction Manual ELENCO Copyright 2017, 2001 by Elenco Electronics, Inc. All rights reserved. Revised 2012 REV-K No part of this book shall be reproduced
More informationK8066 3W MONO AMPLIFIER. Specifications
Total solder points: 34 Difficulty level: beginner 1 2 3 4 5 advanced 3W MONO AMPLIFIER K8066 Small but powerful amplifier suits a wide range of applications. Specifications Output power : 3Wrms (4-8 ohm,
More informationMusic Thing Modular SimpleEQ Construction Guide (1206 version)
Music Thing Modular SimpleEQ Construction Guide (1206 version) Page 1 Useful Links The latest version of this doc and BOM can always be found at http://thonk.co.uk/documents/eq/ A build thread on the Muffwiggler
More informationPacific Antenna Field Strength Indicator Kit
Pacific Antenna Field Strength Indicator Kit Description The Field Strength Indicator kit from Pacific Antenna provides a visual way to monitor the presence and relative strength RF fields through the
More informationThe Useless Machine. Parts Only - Build Guide v0001
TM The Useless Machine Parts Only - Build Guide v0001 For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required: One phillips screwdriver,
More informationAC/DC POWER SUPPLY KIT
AC/DC POWER SUPPLY KIT MODEL K-11 Assembly and Instruction Manual ELENCO Copyright 2016, 1989 by ELENCO All rights reserved. Revised 2016 REV-O 753211 No part of this book shall be reproduced by any means;
More informationStandard Kit #1 (5-way switch)
Standard Kit #1 (5-way switch) Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers 3/8 Drill Bit 1/4 Drill Bit Variable
More informationThe Useless Machine. DIY Soldering Edition. Instruction Guide v0004
The Useless Machine DIY Soldering Edition Instruction Guide v0004 TM For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required: Soldering
More informationTek-Bot Remote Control Transmitter Board Construction
Tek-Bot Remote Control Transmitter Board Construction Purpose This tutorial illustrates the procedure for construction of the Transmitter board for the Tek-bot. A Guide to Soldering Many of you have soldered
More informationunit 3: GENErAL ElectriCAL SySTEM DiAGNOSiS
Electrical/Electronic Systems unit 3: GENErAL ElectriCAL SySTEM DiAGNOSiS lesson 4: wire and connector repairs I. Connector repairs A. Connector repairs involve fixing damaged wires. Wires are marred due
More informationSimon Tilts Assembly Guide
Page 1 of 20 Simon Tilts Assembly Guide Introduction Simon Tilts is a memory game very similar to Simon Says, but instead of pressing buttons, the player is challenged to rotate the device in a specific
More informationLight activated switch
Build instructions, circuit explanation and example applications Issue 1.6 Product information: www.kitronik.co.uk/quicklinks/2112/ TEACHER Light activated switch Introduction About the project kit This
More informationHeartboard PCB Assembly Instructions
Heartboard PCB Assembly Instructions Thanks for purchasing a Heartboard! These instructions will guide you through assembling and testing the Heartboard. Let s get started! Stuff you need Soldering iron
More informationTotal solder points: 79 Difficulty level: beginner advanced GUITAR PREAMPLIFIER WITH HEADPHONE OUTPUT K4102 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 79 Difficulty level: beginner 1 2 3 4 5 advanced GUITAR PREAMPLIFIER WITH HEADPHONE OUTPUT K4102 Practice the guitar without disturbing others. ILLUSTRATED ASSEMBLY MANUAL H4102IP-1
More informationK44 Audio Splitter Board Kit
Introduction The K44 has a great CW reader but one thing that slows most folks down is connecting audio from their receiver to the K44's audio input. recommends using audio from the receiver's audio line
More information