CLASS # 15 ACE DIAMOND BLADES

Size: px

Start display at page:

Download "CLASS # 15 ACE DIAMOND BLADES"

Elijah Andrew Black
6 years ago
Views:

CLASS # 15 ACE DIAMOND BLADES These blades are manufactured exclusively for Ace Industrial Supply and are available in a wide variety of applications under our own Ace Viper and Eagle Cut brands.

1 CLASS # 15 ACE DIAMOND BLADES These blades are manufactured exclusively for Ace Industrial Supply and are available in a wide variety of applications under our own Ace Viper and Eagle Cut brands. They are made to our exact specifications and are not available online or in stores. To ensure customer receives the correct blade for his application, refer to all specs, diameter and arbor sizes as listed below. Also important to remember is that dry blades can be used with or without water to cool them, however, a wet cutting blade cannot be used dry. It must be water cooled to prevent damage and prolong the life of the blade. When reading dimensions, the first measurement is the diameter of the blade, followed by bare arbor size and bushing size. Example: 4 x 7/8-5/8 = 4 blade with a 7/8 bare arbor hole and bushing for 5/8. This means blade will fit 4 saws or grinders with a 5/8 arbor with bushing inserted or 7/8 arbors with bushing removed. Arbors are not threaded. EAGLE CUT - COLD PRESSED SEGMENTED DIAMOND BLADES For general purpose cutting of granite, marble, masonry, brick, block and other concrete materials. Can be used dry or wet. The segment height on is 7mm. DB12E & DB14E have a segment height of 10mm SEGMENTED DRY CUT BLADE 4 x 7/8-5/ SEGMENTED DRY CUT BLADE 4.5 x 7/8-5/ SEGMENTED DRY CUT BLADE 5 x 7/8-5/ SEGMENTED DRY CUT BLADE 7 x 7/8 DM - 5/ SEGMENTED DRY CUT BLADE 8 x 7/8 DM - 5/ SEGMENTED DRY CUT BLADE 10 x 1-5/8 DB12E 12 SEGMENTED DRY CUT BLADE 12 x 1-20mm DB14E 14 SEGMENTED DRY CUT BLADE 14 x 1-20mm

2 EAGLE CUT - HOT PRESSED CONTINUOUS RIM DIAMOND BLADES Designed for ceramic tiles, granite and marble. Provides the smoothest possible chip-free cuts. These blades fit most tile saws. Recommended for wet cutting only. 7mm segment height CONTINUOUS RIM WET BLADE 4 x 5/ CONTINUOUS RIM WET BLADE 4.5 x 5/ CONTINUOUS RIM WET BLADE 5 x 5/ CONTINUOUS RIM WET BLADE 7 x 5/ CONTINUOUS RIM WET BLADE 8 x 5/ CONTINUOUS RIM WET BLADE 10 x 1-5/8 EAGLE CUT - COLD PRESSED TURBO DIAMOND BLADES Designed for granite, marble, engineering bricks, concrete, block, hard clay roof tiles, masonry products and reinforced concrete. Provides smooth, clean cuts with no chipping. Wet or dry cutting. 7mm segment height FINE TURBO BLADE 4 x 7/8-5/ FINE TURBO BLADE 4.5 x 7/8-5/ FINE TURBO BLADE 5 x 7/8-5/ FINE TURBO BLADE 7 x 7/8 DM - 5/ FINE TURBO BLADE 10 x 1-5/ FINE TURBO BLADE 12 x 1-20mm FINE TURBO BLADE 14 x 1-20mm

EAGLE CUT - DOUBLE ROW DIAMOND CUP WHEELS For grinding and polishing granite, marble,

These cup wheels have 5/8-11 threaded arbors to fit most angle grinders.

5 x 5/8-11 10102 7 DOUBLE ROW CUP WHEEL 7 x 5/8-11 EAGLE CUT - SWIRLY CUP DIAMOND CUP

10103 4 SWIRLY TYPE CUP WHEEL 4 x 5/8-11 10104 4.5 SWIRLY TYPE CUP WHEEL 4.

3 EAGLE CUT - DOUBLE ROW DIAMOND CUP WHEELS For grinding and polishing granite, marble, concrete and concrete products, masonry materials and all types of natural stone. These cup wheels have 5/8-11 threaded arbors to fit most angle grinders DOUBLE ROW CUP WHEEL 4 x 5/ DOUBLE ROW CUP WHEEL 4.5 x 5/ DOUBLE ROW CUP WHEEL 7 x 5/8-11 EAGLE CUT - SWIRLY CUP DIAMOND CUP WHEELS For smooth grinding of concrete and stone or epoxy over concrete and stone. These cup wheels have 5/8-11 threaded arbors to fit most angle grinders SWIRLY TYPE CUP WHEEL 4 x 5/ SWIRLY TYPE CUP WHEEL 4.5 x 5/ SWIRLY TYPE CUP WHEEL 7 x 5/8-11

ACE VIPER - HOT PRESSED TURBO STONE DIAMOND BLADES For hard aggregates, stone, granite, marble and engineering bricks. Smooth cutting with good stock removal. Wet cutting Recommended.

5 x 7/8-5/8 11032 5 FINE TURBO STONE BLADE 5 x 7/8-5/8 11033 6 FINE TURBO STONE BLADE 6 x 7/8-5/8 11034 7 FINE TURBO STONE BLADE 7 x 7/8 DM - 5/8 11035 8 FINE TURBO STONE BLADE 8 x 7/8 DM - 5/8 11036

4 ACE VIPER - HOT PRESSED TURBO STONE DIAMOND BLADES For hard aggregates, stone, granite, marble and engineering bricks. Smooth cutting with good stock removal. Wet cutting Recommended. Segment height is 10mm. Arbors have 4 screw holes for use with flush cut adapter # 1FCA FINE TURBO STONE BLADE 4 x 7/8-5/ FINE TURBO STONE BLADE 4.5 x 7/8-5/ FINE TURBO STONE BLADE 5 x 7/8-5/ FINE TURBO STONE BLADE 6 x 7/8-5/ FINE TURBO STONE BLADE 7 x 7/8 DM - 5/ FINE TURBO STONE BLADE 8 x 7/8 DM - 5/ FINE TURBO STONE BLADE 9 x 7/8 DM - 5/ FINE TURBO STONE BLADE 10 x 1-5/8 ACE VIPER - PRO LASER WELDED CONCRETE DIAMOND BLADES Designed for high performance cutting of an extensive range of masonry and concrete materials including bricks, blocks, slate, stone, cured concrete, etc. These blades have a DPH, (Drive Pin Hole), next to the arbor for high speed saws. 10mm segment height PRO LASER CONCRETE BLADE 12 x 1-20mm PRO LASER CONCRETE BLADE 14 x 1-20mm 10061M 14 PRO LASER CONCRETE BLADE 14 x TRUE 20mm PRO LASER CONCRETE BLADE 16 x 1-20mm PRO LASER CONCRETE BLADE 18 x 1-20mm PRO LASER CONCRETE BLADE 20 x 1-20mm

ACE VIPER - ASPHALT/GREEN CONCRETE DIAMOND BLADES These deep-drop segmented blades are designed for cutting asphalt, asphalt over concrete, green concrete, (concrete that has set but has not hardened.

5 ACE VIPER - ASPHALT/GREEN CONCRETE DIAMOND BLADES These deep-drop segmented blades are designed for cutting asphalt, asphalt over concrete, green concrete, (concrete that has set but has not hardened. Usually within 48 hours after being poured), and other highly abrasive materials. 10mm segment height DEEP DROP ASPHALT BLADE 12 x 1-20mm DEEP DROP ASPHALT BLADE 14 x 1-20mm 10042M 14 DEEP DROP ASPHALT BLADE 14 x TRUE 20mm DEEP DROP ASPHALT BLADE 16 x 1-20mm ACE VIPER - HOT PRESSED PORCELAIN DIAMOND BLADES Designed for chip-free, smooth cutting of porcelain, ceramic tiles, granite and marble. These blades are recommended for wet cutting and are primarily used on wet cutting tile saws. These are Hot Dog style blades. 7mm segment height PORCELAIN CONT. RIM BLADE 4 x 5/ PORCELAIN CONT. RIM BLADE 4.5 x 5/ PORCELAIN CONT. RIM BLADE 7 x 5/ PORCELAIN CONT. RIM BLADE 10 x 1-5/8

ACE VIPER - TUCK POINT DIAMOND BLADES The thick segments on these diamond blades, (6.

They provide for fast, easy removal of grouted or mortared joint material.

10070 4 TUCK POINT DIAMOND BLADE 4 x 7/8-5/8 10071 4.5 TUCK POINT DIAMOND BLADE 4.

6 ACE VIPER - TUCK POINT DIAMOND BLADES The thick segments on these diamond blades, (6.4mm) are specially designed for mortared expansion joints and slotting granite, marble, concrete etc. They provide for fast, easy removal of grouted or mortared joint material. The tungsten carbide inserts provide superior cutting performance and greatly extended blade life. These blades are recommended for wet cutting TUCK POINT DIAMOND BLADE 4 x 7/8-5/ TUCK POINT DIAMOND BLADE 4.5 7/8-5/ TUCK POINT DIAMOND BLADE 7 x 7/8 DM - 5/8 ACE VIPER - CRACK CHASER DIAMOND BLADES These crack chaser blades have a 3/8 thick, V shaped design with diamond embedded segments. They are specifically engineered to efficiently clean out and repair concrete cracks by smooth grooving CRACK CHASER BLADE 4 x 7/8-5/ CRACK CHASER BLADE 4.5 7/8-5/ CRACK CHASER BLADE 5 x 7/8-5/ CRACK CHASER BLADE 7 x 7/8 DM - 5/8

7 ACE VIPER - PRO ALL PURPOSE DIAMOND BLADES These are professional laser welded all purpose blades with vent holes for better cooling. They are designed for cutting cured concrete, brick, block, brick pavers, bluestone, asphalt, limestone etc. Can be used wet or dry. 10mm segment height ALL PURPOSE PRO BLADE 12 x 1-20mm ALL PURPOSE PRO BLADE 14 x 1-20mm ALL PURPOSE PRO BLADE 16 x 1-20mm ACE VIPER - DUCTILE IRON DIAMOND BLADES These are laser welded diamond blades designed to cut very abrasive ductile iron. The swirl pattern in the blade prevents pipe-pinching and heat build up that could damage other blades. Made for high powered gas walk behind saws DUCTILE IRON BLADE 12 x 1-20mm DUCTILE IRON BLADE 14 x 1-20mm 10091M 14 DUCTILE IRON BLADE 14 x TRUE 20mm

ACE VIPER - LASER BRICK, MASONRY & STONE DIAMOND BLADES These are laser welded diamond blades with a wide skew U slot and are designed for cutting bricks, block, masonry, asphalt, asphalt over

8 ACE VIPER - LASER BRICK, MASONRY & STONE DIAMOND BLADES These are laser welded diamond blades with a wide skew U slot and are designed for cutting bricks, block, masonry, asphalt, asphalt over concrete and stone products. Can be used wet or dry on gas walk behind saws. 10mm segment height BRICK, MASON, STONE BLADE 12 x 1-20mm BRICK, MASON, STONE BLADE 14 x 1-20mm ACE VIPER - TAZ PREMIUM GENERAL PURPOSE TURBO BLADES These are segmented turbo blades for general purpose cutting of reinforced concrete, concrete, hard clay roof tiles, marble, granite, and many other masonry materials. Vent holes allow blade to run cooler during dry or wet cutting. 12mm segment height TAZ PREMIUM GP BLADE 12 x 1-20mm TAZ PREMIUM GP BLADE 14 x 1-20mm 11042M 14 TAZ PREMIUM GP BLADE 14 x TRUE 20mm

ACE VIPER - LASER WELDED GENERAL PURPOSE BLADES These are laser welded,

concrete and masonry products. Segment height is 10mm.

1-20mm DB14VM 14 GENERAL PURPOSE BLADE 14 x TRUE 20mm ACE VIPER - FLUSH CUT

stone, granite, marble and tiles when using our stone cutting blades only.

thread shafts. They are heavy duty aluminum and come with (4) 4mm screws.

9 ACE VIPER - LASER WELDED GENERAL PURPOSE BLADES These are laser welded, segmented general purpose blades for wet or dry cutting of brick, block, hard concrete and masonry products. Segment height is 10mm. DB12V 12 GENERAL PURPOSE BLADE 12 x 1-20mm DB14V 14 GENERAL PURPOSE BLADE 14 x 1-20mm DB14VM 14 GENERAL PURPOSE BLADE 14 x TRUE 20mm ACE VIPER - FLUSH CUT ADAPTER FOR STONE CUTTING BLADES These adapters allow for flush cutting into stone, granite, marble and tiles when using our stone cutting blades only. They adapt the stone blades with 20mm 4 hole arbors for mounting on 5/8-11 thread shafts. They are heavy duty aluminum and come with (4) 4mm screws. For use with 4 hole arbor on stone blades # s ITEM#: 1FCA DESCRIPTION: FLUSH CUT ARBOR ADAPTER W/ 4mm SCREWS

It is engineered with a high concentration of diamonds with an extremely strong bond.

10 CLASS # 13 METAL CUT DIAMOND BLADE This new blade is a revolutionary line of diamond wheels for metal cutting applications. It s designed to cut metal, stainless steel and a variety of other ferrous metals with less odor and debris compared to conventional abrasives. It is engineered with a high concentration of diamonds with an extremely strong bond. They can handle higher RPM's than traditional abrasive wheels and unlike traditional cut-off wheels these blade do not change over time, resulting in a blade that remains the same from the first cut to final cut. Specifications: 3 x 3/8 x ,000 RPM 4-1/2" x.050 x 7/8", 5/8" - 13,000 RPM 5 x.050 x 7/8, 5/8-12,000 RPM 7 x.050 x 7/8, 5/8 /Diamond - 8,730 RPM 14 x 1 /20mm 5,460 RPM Ultra Thin Kerf - Cuts Extremely Fast Vacuum Brazed Technology - For Extra Long Life Blade Life is Equivalent to 65 Abrasive Wheels. ITEM#: 3MTL 45MTL 5MTL 7MTL 14MTL DESCRIPTION: 3 METAL CUTTING DIAMOND BLADE 4-1/2 METAL CUTTING DIAMOND BLADE 5 METAL CUTTING DIAMOND BLADE 7 METAL CUTTING DIAMOND BLADE 14 METAL CUTTING DIAMOND BLADE

11 CLASS # 15 DIAMOND BLADES These ACE INDUSTRIAL SUPPLY diamond blades are manufactured by MK DIAMOND. We carry all of the designated blades for cutting brick, block, concrete, asphalt, tile, and most vitreous materials. They are top quality, precision diamond cutting wheels manufactured to strict 900 industry standards and are 39% diamond concentrate, which is the highest diamond concentration in the industry. They re engineered to provide optimum cutting performance under most conditions while maintaining an extra long service life, and are available for many different applications. Refer to following charts for the correct size and application. Some blades also have a drive pin hole, (DPH) which is a small hole next to the arbor and secures the blade on high RPM saws. Be sure to get saw model, arbor size, and exact material being cut to insure sale of proper blade. NOTE: A WET BLADE CAN ONLY BE USED WET AND A DRY BLADE CAN BE USED EITHER WET OR DRY. A WET BLADE CAN BE USED ON A SAW UP TO 35HP AND CAN BE USED CONTINUOSLY, A DRY BLADE CAN ONLY BE USED ON A SAW UP TO 16HP AND IS ONLY MEANT TO CUT FOR 1 FOOTAND THEN IT MUST COOL OFF. DESIGNED FOR CUTTING TILE AND VITREOUS MATERIAL. THE EDGE OF THE BLADE IS SOLID, CONTINUOUS AND CONTAINS 39% DIAMOND CONCENTRATION. CONTINUOUS RIM DIAMOND BLADE ITEM# DIMENSIONS USEAGE 4CR 4 x 5/8 ARBOR WET/DRY CUT - TILE 7CR 7 x 5/8 ARBOR WET/DRY CUT - TILE 10CR 10 x 5/8 ARBOR WET/DRY CUT - TILE

DESIGNED FOR CUTTING MOST CONCRETE, ASPHALT, BRICK AND BLOCK. THE RIM OF THE BLADE IS DIVIDED INTO SEGMENTS THAT CONTAIN DIAMOND PARTICLES.

080 x 5/8 DRY SEGMENTED 10DSB 10 x.070 x 5/8 WET/DRY SEGMENTED 12WDS 12 x.110 x 1 WET/DRY SEGMENTED 14WDS 14 x.125 x 1 WET/DRY SEGMENTED DESIGNED FOR HIGH SPEED CUTTING.

12 DESIGNED FOR CUTTING MOST CONCRETE, ASPHALT, BRICK AND BLOCK. THE RIM OF THE BLADE IS DIVIDED INTO SEGMENTS THAT CONTAIN DIAMOND PARTICLES. DRY SEGMENTED DIAMOND BLADE ITEM# DIMENSIONS USEAGE 4DSB 4 x.080 x 5/8 DRY SEGMENTED 412DSB 4-1/2 x.080 x 7/8 DRY SEGMENTED 5DSB 5 x.080 x 5/8 DRY SEGMENTED 7DSB 7 x.080 x 5/8 DRY SEGMENTED 10DSB 10 x.070 x 5/8 WET/DRY SEGMENTED 12WDS 12 x.110 x 1 WET/DRY SEGMENTED 14WDS 14 x.125 x 1 WET/DRY SEGMENTED DESIGNED FOR HIGH SPEED CUTTING. THE RIM OF THE BLADE IS CONTINUOUS WITH SEGMENTS THAT ARE THICKER THAN THE RIM. THIS WILL PROVIDE FASTER CUTTING BECAUSE IT CAN REMOVE THE RESIDUE OF THE CUT MATERIAL FASTER. THESE ARE TOP OF THE LINE PRO BLADES. TURBO DIAMOND BLADE ITEM# DIMENSIONS USEAGE 4TB 4 x 5/8 ARBOR WET/DRY 412TB 4-1/2 x 5/8 ARBOR WET/DRY 5TB 5 x 5/8 ARBOR WET/DRY 7TB 7 x 5/8 ARBOR WET/DRY 10TB 10 x 5/8 ARBOR WET/DRY 12TB 12 x 1 ARBOR WET/DRY 14TB 14 x 1 ARBOR WET/DRY DESIGNED FOR CUTTING BRICK ONLY. THE RIM OF THE BLADE IS DIVIDED INTO SEGMENTS THAT CONTAIN DIAMOND PARTICLES. SEGMENTED BRICK ONLY ITEM# DIMENSIONS USEAGE 12BRB 12 x.110 X 1 BRICK CUTTING 14BRB 14 x.110 X 1 BRICK CUTTING DESIGNED FOR CUTTING BLOCK ONLY. THE RIM OF THE BLADE IS DIVIDED INTO SEGMENTS THAT CONTAIN DIAMOND PARTICLES. SEGMENTED BLOCK ONLY ITEM# DIMENSIONS USEAGE 12BLB 12 x.110 X 1 BLOCK CUTTING 14BLB 14 x.110 X 1 BLOCK CUTTING

CURED CONCRETE DRY CUTTING ITEM# DIMENSIONS USEAGE 12CCD 12 x.125 x 1 w/ DPH DRY CUTTING 14CCD 14 x.125 x 1 w/ DPH DRY CUTTING DESIGNED FOR CUTTING GRANITE. DRY CUTTING. GRANITE ITEM# DIMENSIONS USEAGE 12GDB 12 x.

13 DESIGNED FOR CUTTING GREEN CONCRETE, AND ASPHALT, ASPHALT / GREEN CONCRETE ITEM# DIMENSIONS USEAGE 12AGCD 12 x.125 x 1 w/ DPH DRY CUTTING 14AGCD 14 x.125 x 1 w/ DPH WET/DRY CUTTING 14AC x.250 x 1 w/ DPH WET/DRY CUTTING DESIGNED FOR CUTTING CURED CONCRETE. DRY CUTTING. CURED CONCRETE DRY CUTTING ITEM# DIMENSIONS USEAGE 12CCD 12 x.125 x 1 w/ DPH DRY CUTTING 14CCD 14 x.125 x 1 w/ DPH DRY CUTTING DESIGNED FOR CUTTING GRANITE. DRY CUTTING. GRANITE ITEM# DIMENSIONS USEAGE 12GDB 12 x.125 x 1 w/ DPH DRY CUTTING 14GDB 14 x.125 x 1 w/ DPH DRY CUTTING DESIGNED FOR CUTTING CURED CONCRETE. WET CUTTING. CURED CONCRETE WET CUTTING ITEM# DIMENSIONS USEAGE 12CCW 12 x.125 x 1 w/ DPH WET CUTTING ONLY 14CCW 14 x.125 x 1 w/ DPH WET CUTTING ONLY

14 CLASS # 15 ACE BRAND DIAMOND BLADES These new, segmented diamond blades were manufactured and tested exclusively for Ace Industrial Supply and are not available anywhere else on the planet. They are wet or dry cutting blades with a thickness of.125 and available in 14 and 12. Both sizes feature a 1 arbor with a knockout bushing for 20mm saws like Stihl. These blades were tested against MK Diamond Vector Blades and Laser Blades with these findings; Our sintered blade, (Eagle Cut) lasted 3.5% longer than MK and our Laser Blade, (Ace Viper), cut 11% faster and lasted 232% longer than MK. Our Eagle Cut blades outperformed even MK s Laser Blades while our Ace Viper Laser blades outperformed and outlasted both the MK sintered and MK laser weld blades. These new diamond blades are not only proven better than MK diamond but we have acquired them at a price far better than the competition. Both the 12 Eagle Cut and Ace Viper blades have a maximum RPM of 6,300 and both 14 blades are rated at 5,500 RPM. Both blades are ideal for general purpose and concrete. ITEM#: DB12E DB12V DB14E DB14V DESCRIPTION: 12 EAGLE CUT DIAMOND BLADE 12 ACE VIPER DIAMOND BLADE - LASER 14 EAGLE CUT DIAMOND BLADE 14 ACE VIPER DIAMOND BLADE - LASER

CLASS # 15 DIAMOND BLADES Vermont American diamond blades cut two to three times faster than standard abrasive wheels and they last 85 times longer than standard

These blades are segmented blades and recommended for cutting concrete, block, brick, and general masonry materials. They re.

15 CLASS # 15 DIAMOND BLADES Vermont American diamond blades cut two to three times faster than standard abrasive wheels and they last 85 times longer than standard abrasive blades which reduces blade changes and minimizes job interruptions. These blades are segmented blades and recommended for cutting concrete, block, brick, and general masonry materials. They re.06 thick and have 7/8 arbors with a 5/8 bushing included. Diameter: 4-1/2 RPM: 13,200 Thickness:.06 Arbor: 7/8 with 5/8 Bushing Diameter: 4 RPM: 14,500 Thickness:.06 Arbor: 7/8 with 5/8 Bushing ITEM#: VA4 VA412 DESCRIPTION: 4 VERMONT AMERICAN DIAMOND BLADE 4-1/2 VERMONT AMERICAN DIAMOND BLADE

The blade utilizes Micro Bead technology and a core slot design to provide a thin kerf that will ensure a consistent cutting edge and eliminate porcelain surface chipping

16 CLASS # 15 PORCELAIN DIAMOND BLADE These MK Hot Dog diamond blades are ideal for the wet cutting of porcelain, vitreous tile and ceramic tile. They re continuous rim blades and must be used with a wet cutting saw. The blade utilizes Micro Bead technology and a core slot design to provide a thin kerf that will ensure a consistent cutting edge and eliminate porcelain surface chipping even with the hardest porcelain tile. They ll cut 10% faster while lasting 20% longer than standard blades. Specifications: Premium Grade 5/8 bore Wet Cut Only For Porcelain, Vitreous and Ceramic Tile ITEM#: DESCRIPTION: 10CRHD 10 WET CUT HOT DOG PORCELAIN BLADE 412CRHD 4-1/2 WET CUT HOT DOG PORCELAIN BLADE

CLASS # 15 TIGER TOOTH DIAMOND BLADES These premium grade multipurpose diamond blades are dry cutting segmented blades for steel, concrete, masonry, ductile, wood and plastic.

17 CLASS # 15 TIGER TOOTH DIAMOND BLADES These premium grade multipurpose diamond blades are dry cutting segmented blades for steel, concrete, masonry, ductile, wood and plastic. Tiger Tooth blades utilize a vacuum brazing process to bond diamond crystals to the segments and the core is made of solid steel to prevent warping. These blades provide improved safety, better performance, greater versatility and a greater value than other blades. They can be used on any gas or electric chop saw or hand grinder and are the perfect diamond blade for contractors, plumbers, electricians and handymen. Specifications: 14 x 1 arbor x.125 thickness 12 x 1 arbor x.125 thickness 9 x 5/8 arbor x.095 thickness 7 x 7/8-5/8 arbor with diamond knockout x.090 thickness 4-1/2 x 7/8-5/8 arbor x.080 thickness 4 x 7/8-5/8 arbor x.080 thickness (Note: 7/8-5/8 arbors are 7/8 bore with a ring to bush to 5/8 ) ITEM#: DESCRIPTION: 14TTD TIGER TOOTH DIAMOND BLADE 14 x 1 12TTD TIGER TOOTH DIAMOND BLADE 12 x 1 9TTD TIGER TOOTH DIAMOND BLADE 9 x 5/8 7TTD TIGER TOOTH DIAMOND BLADE 7 x <>-7/8-5/8 412TTD TIGER TOOTH DIAMOND BLADE 4-1/2 x 7/8-5/8 4TTD TIGER TOOTH DIAMOND BLADE 4 x 7/8-5/8

CLASS # 15 PLANK KUTTER DIAMOND BLADE These are MK Diamond Plank Kutter blades for cutting HardiPlank, a cement fiber material that can be made to resemble wood or stucco but is impermeable to common

18 CLASS # 15 PLANK KUTTER DIAMOND BLADE These are MK Diamond Plank Kutter blades for cutting HardiPlank, a cement fiber material that can be made to resemble wood or stucco but is impermeable to common forms of damage that threaten wood such as water damage, rot and termites. HardiPlank is also designed to retain paint longer than wood without chipping or peeling, and is fire resistant. These are top quality, precision diamond blades that are manufactured to the strict 900 industry standards. They re 39% diamond concentrate, the highest diamond concentration in the industry and are engineered to provide optimum cutting performance under most conditions while maintaining an extra long service life. ITEM#: DESCRIPTION: 7HPDB 7 x 0.80 x 5/8 -DIA - MK PLANK KUTTER 10HPDB 10 x 0.90 x 5/8 -DIA - MK PLANK KUTTER

They have a 7/8 arbor with a 5/8 bushing to fit a standard electric hand grinder for removal of old and cracked mortar quickly and cleanly.

19 CLASS # 15 TUCK POINT DIAMOND BLADE These tuck point diamond blades are the ideal solution to masonry and brick repair. They are 1/4 thick, the perfect width to grind out old mortar in between bricks and tile. They have a 7/8 arbor with a 5/8 bushing to fit a standard electric hand grinder for removal of old and cracked mortar quickly and cleanly. They re segmented, dry cutting diamond blades that you can use to cut about 1/2 from old mortar or they can be used to grind out wall cracks for re-filling. Import. ITEM#: DESCRIPTION: 4DTP 4 TUCK POINT DIAMOND BLADE 412DTP 4-1/2 TUCK POINT DIAMOND BLADE

CLASS # 15 14 VECTOR DIAMOND BLADE This is a general purpose, dry cutting and segmented diamond blade that is ideal

Available in 14 diameter, (356mm), or 12, (305 mm) with a thickness of.125.

20 CLASS # VECTOR DIAMOND BLADE This is a general purpose, dry cutting and segmented diamond blade that is ideal for brick, block, pavers, concrete and bluestone. Available in 14 diameter, (356mm), or 12, (305 mm) with a thickness of.125. They have a 1 arbor with a drive pin hole (DPH), for walk behind saws. The segment height is 10 mm and this blade can be used wet or dry. ITEM#: 14WDSV 12WDSV DESCRIPTION: 14 VECTOR DIAMOND BLADE 12 VECTOR DIAMOND BLADE

21 CLASS # 15 7 DIAMOND BLADE This is Skil's newest diamond cutting blade. It's 7" for tile cutters, but will also work great in 7-1/4" circular saws. This is a Turbo blade that cuts twice as fast, and last 50 times longer than a normal abrasive cutting blade because of its' patented construction, diamond concentrate, and ventilation holes for cooling and durability. These blades will cut brick, cement block, concrete, ceramic tile, fiber cement board, and other masonry material. They have a 5/8" diamond knockout. Maximum rpm is ITEM#: SB79510 DESCRIPTION: SKIL 7 WET/DRY DIAMOND BLADE

They are available in 4 and 4-1/2 diameter with a 5/8"-11-thread nut to fit a standard electric

22 CLASS # 15 DIAMOND GRINDING CUPS These are standard grade, double or single row diamond cup wheels for wet or dry grinding of stone. They are available in 4 and 4-1/2 diameter with a 5/8"-11-thread nut to fit a standard electric hand grinder. ITEM#: DESCRIPTION: 4DRDCW 4 DOUBLE ROW DIAMOND GRINDING CUP 4SDRCW 4 SINGLE ROW DIAMOND GRINDING CUP 412DRGC 4-1/2 DOUBLE ROW DIAMOND GRINDING CUP

BY LACKMOND TILE PRODUCTS AND SOLUTIONS EQUIPMENT ACCESSORIES DIAMOND TOOLS

BY LACKMOND TILE PRODUCTS AND SOLUTIONS EQUIPMENT ACCESSORIES DIAMOND TOOLS TILE PRODUCTS AND SOLUTIONS EQUIPMENT ACCESSORIES DIAMOND TOOLS BEAST 10" WET TILE SAW BLADE SIZE: MOTOR CAPACITY: RIP CUT CAPACITY: DIAGONAL CUT CAPACITY: DEPTH OF CUT AT 90 : DEPTH OF CUT AT 45 : BEVEL: