TRILENNIUM STRIKE PLATE INSTALLATION - HAND ROUTING
|
|
- Lizbeth McLaughlin
- 5 years ago
- Views:
Transcription
1 OVERVIEW Parts Included in System: Templaco Jamb Right Templaco Jamb Left Templaco Jamb Dust Box Through-Hole All parts above available in Endura Part#: TC- TEMP-TEMPLACO Dust Box Templaco Jamb Dust Box Through-Hole Reinforcing Plate Plate 1/2 Router Bit 5/8 OD Router Guide and Nut Templaco Jamb Right Hand Templaco Jamb Left Hand Additional Parts Required: Router 1/2 Router Bit 5/8 OD Router Guide and Nut Hammer Hand drill Pencil Measuring tape/ Ruler Clamps Plates Reinforcing Plates Dust Boxes 1 of 13
2 Router Setup In order to make use of Templaco System and not damage them in the process, a 5/8 OD Router Guide must be used. To install 5/8 OD Router Guide, align Nut with opening on router base. Align and insert Guide into the Nut, and tighten until secure. 2 of 13
3 1. Aligning A. Measure and Mark Lever Centerline. B. Located Centerline Leverbore 3-5/8 Locate the Leverbore centerline on the jamb. Measure 3-5/8 toward the top of the jamb from Lever Centerline and Mark. This is your Plate Centerline. Note Orientation Left Hand 8/0 Top 6/0 Top Center Bottom Right Hand 3 of 13
4 1. Aligning Cont. C. Align Centerline of with the Center Plate Centerline Mark. Centerline D. Using a Hammer, Secure Locking Pins into Jamb. E. Secure with Claps at each End. Secure to the table to ensure no movement will occur. 4 of 13
5 2. Routing for the Plate Assembly. A. Set Router Depth to 1/8 B. Route Slots for Plates. Trace the perimeter of the strike template then make several passes across the middle until the entire strike area is removed to the 1/8 depth. CAUTION : Be sure to let the router comes to a complete stop before removing to prevent damage to the template system C. Repeat for All Three Required Locations Left Hand 8/0 Top 6/0 Top Center Bottom 3-5/8 8/0 Top 6/0 Top Center Leverbore Bottom Right Hand 5 of 13
6 2. Routing for Dust Box Hole C. Remove Clamps and. D. Disengage Locking Pins. Release Clamps securing template to table. Using the claw end of the hammer release locking pins from jamb. 3. Routing for Dust Box Hole A. Install Dust Box. Note: Be sure the red plastic guide sits inside the strike plate cut out. 6 of 13
7 3. Routing for Dust Box Hole B. Using Hammer, Secure with Locking Pins. C. Secure with Dust Box to Work Table with Clamps. 7 of 13
8 3. Routing for Dust Box Hole Cont. D. Adjust Router Bit. E. Route Dust Box Hole. Measure and adjust drill bit to 17/16 depth. CAUTION : Be sure to let the router comes to a complete stop before removing to prevent damage to the template system F. Remove. Remove clamps securing template to working surface. Using the claw end of the hammer release locking pins from jambs. I. Repeat Routing for Remaining Locations. Repeat steps A-F for the remaining locations. 8 of 13
9 4. Mounting Plates A. Assemble Plates. Dust Box Plate 3/4 Screws Attaching Dust Box and Reinforcing Plate Dust Box feet Reinforcing Plate Arms Reinforcing Plate Attach the Dust Box to the Reinforcing Plate. Align the 3 holes on the Plate with the Reinforcing Plate. Orient as shown. Reinforcing plate arms Dust Box Feet The Dust Box feet should align with the groves parallel to the roller. The Reinforcing Plate plate arms should sit inside the Dust Box. B. Attach Plate Assembly to Jamb. Install (2) 3/4 screws into each strike assembly, and leave the 2-1/2 center screw for the field installation 9 of 13
10 5. Trilennium Compatible Astragal Plate Preparation. The Trilennium Compatible Astragal requires clearance pockets behind the astragal s strike plates in order for the deadbolts to be thrown into the extended position. Without these clearance pockets, the deadbolt will come in contact with the door and will not lock. Correct Application Incorrect Application Deadbolt Deadbolt Astragal Astragal 1/2 1 Panel Panel 10 of 13
11 5. Trilennium Compatible Astragal Plate Preparation. A. Determine Lever Crossbore Centerline. B. Determine the center strike plate centerline. Measure and determine the passive doors crossbore centerline. Top Measure 3/8 up from the leverbore centerline towards the top of the panel. This is the center strike centerline. Top Center Center 3/8 Lever Crossbore Lever Crossbore 3/8 Bottom Bottom 11 of 13
12 5. Trilennium Compatible Astragal Plate Preparation. C. Determine the lower strike plate centerline. D. Determine the Upper strike plate centerline. Measure from the center strike centerline down 24-5/16 toward bottom of door and mark. This is the lower strike plate centerline. From strike centerline measure up and mark at: 33-3/32 for 8/0 doors 23-1/32 for 6/8 doors Top Upper Top 8/0: 33-3/32 6/8: 23-1/32 Center Center 24-5/ /16 Lower Lower Bottom Bottom 12 of 13
13 5. Trilennium Compatible Astragal Plate Preparation. E. Drill deadbolt clearance pocket. Determine the center point on the upper center and lower strike plate center lines and mark the location. Using a 1 spade bit drill a 1/2 deep hole at each center point. Clear debris from stile. Install Trilennium Compatible Astragal. Upper Top Upper Centerline Top Upper Center Centerline Center Center Lower Centerline Lower Bottom Lower Bottom 13 of 13
TRILENNIUM FULL SCOPE (FS) TEMPLATE INSTRUCTIONS
Overview Parts Included in Template System: Full Scope (FS) Template Rails, with ø 2-1/8 Crossbore Guides. FS Router Carrier (for 1-3/4, 2 & 2-1/4 Doors) FS Bridges, Stops and Twist Bolts 13/16 x 5 Router
More informationINSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY
INSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY A B C L M N D E F G O P Q H I J Tools provided in Amesbury installation kit: (A) door router fixture, (B) doorframe router fixture, (C) ½
More informationEntry Mortise Handleset
1. Pencil 2. No. 2 and No. 3 Phillips Head Screwdrivers 3. No. 1 and No. 2 Slotted Screw Drivers 4. 1/8" Allen Head Wrench 5. 3/4" Wood Chisel or Corner Chisel 6. Measuring Device 7. Lock Mortising Tool
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More informationInstallation Guide. Cue Front Unit (Code and Key) Cue Front Unit (RFID) Cue Rear Unit (Latch and Bolt)
Installation Guide Cue Front Unit (Code and Key) Cue Front Unit (RFID) Cue Rear Unit (Latch and Bolt) Table of Contents Before Lock Installation3 Surface Mount Installation For door thickness measuring
More informationED5800 (A) Series. Installation Instructions. Concealed Vertical Rod. Exit Device WARNING
Strike Shim (2) Supplied Strike Plate (3) 10-24 x 3/4" PFHMS (6) 10-24 x 1/2" PFHMS Top Latch TopTube Concealed Vertical Rod Exit Device Important: For use with metal doors only. Device is packed ready
More informationDoor Hardware Installation Instructions. For Assistance Call:
For Assistance Call: Door Hardware Installation Instructions Single Cylinder NOTE: s fit doors 1-3/4 to 2-1/4 thick. For thicker doors, please call customer service. Carefully unpackage all components
More information* * 98/9950WDC. Fire-Rated Devices include these. additional components. 1-Point Latch (LBL)
*24739468* 24739468 98/9950WDC Installation Instructions 1-Point Latch (LBL) Fire-Rated Devices include these additional components Metal Edge Wrap required for 60 and 90-minute applications 2-Point Latch
More informationInstalling Your Electronic Deadbolt
Ultra Security Plus Electronic Deadbolt Installation Instructions http://www.hberger.com/video-gallery/electronic-deadbolt New Installation Lock Location Preparation (Skip this section if you door has
More informationInstallation Instructions For The 8850FL Series Mortise eboss
Installation Instructions For The 8850FL Series Mortise eboss Electronic Battery Operated Security Solution FEATURES Battery Operated (Hardwire Capable) Motorized Grade 1 Mortise Lock 94 User Code Capacity
More informationINSTRUCTIONS TS93 GSR PT RIGHT HAND ACTIVE LEFT HAND INACTIVE RIGHT HAND INACTIVE LEFT HAND ACTIVE
INSTRUCTIONS ATTENTION!!! Before you begin, determine installation type (RIGHT HAND ACTIVE OR INACTIVE). Door coordinator suitable for door from 59 to 98 in width. Inactive door width in the case of unequal
More informationTwo Panel Frameless Bypass Door
INSTALLATION INSTRUCTIONS Two Frameless Bypass Door Series 00 Please Record Model Number From Carton Label Here Please read these instructions carefully to familiarize yourself with the required tools,
More informationINSTRUCTIONS FOR HIT LOCK MORTISER
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-200 LOCK MORTISER WHEN USING POWER TOOLS ALWAYS WEAR EYE AND EAR
More informationED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS
ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS Ver.2 1300 SERIES CONCEALED VERTICAL ROD DEVICE Top Strike Latch Screws Strike Screws Release Plunger Top Latch Plunger Screws
More informationPlease read and understand all instructions before beginning. These instructions cover impact and non-impact aluminum French Door 650/750.
The performance and proper operation of a door is only as good as the installation. By following these instructions, the probability of a good installation greatly increases. Please read and understand
More informationStage 2: Preparing the door (read in conjunction with Hole Drilling Options on back of Template).
There are three stages to fitting the CL100 mortise case: Stage 1: Marking out the position of the lock. Stage 2: Preparing the door by mortising and drilling holes. Stage 3: Fitting lock, door furniture,
More informationSCHLAGE SENSE. Smart Deadbolt. Installation Instructions. Download the Schlage Sense app to get started!
SCHLAGE SENSE Smart Deadbolt Installation Instructions Download the Schlage Sense app to get started! Schlage Sense Installation Instructions Package Contents Camelot Style shown throughout guide. Support
More informationBefore Lock Installation Surface Mount Installation. Door Preparation
Installation Guide Before Lock Installation... 3 Surface Mount Installation For door thickness measuring between.01" -.91" (0.2 mm - 23 mm)... 4 Required Components... 4 Installation... 5 Door Preparation
More informationPlease read and understand all instructions before beginning. These instructions cover the non-impact aluminum French Door 101.
The performance and proper operation of a door is only as good as the installation. By following these instructions, the probability of a good installation greatly increases. Please read and understand
More informationShim (2) Supplied. Strike Plate. (3) x 5/8" PFHMS or 10 x 1" PFHWS. Top Latch. (3) x 1/4" PRHMS. Latch Cover. (2) 8 x 3/8" PFH AB SMS
Installation Instructions ED5400 (A) Series ED5470 (B) Series Surface Vertical Rod Exit Devices Strike Angle Must Engage Strike Top Strike 10-24 PFHMS Top Bracket and Strike required for ED5470. Shim (2)
More informationLATCHBOLT FILLER PLATE ASA FILLER PLATE A. SINGLE DOOR B. DOUBLE DOOR WITH MULLION C. DOUBLE DOOR WITHOUT MULLION END COVER MOUNTING BRACKET
F2000R 2012.03 1/4 x1 1/2 (9 PCS) SELF TAPPING MACHINE SCREWS 1/4-20P x 3/4 (3 PCS) 1/4-20P x 3/4 (6 PCS) ROUND HEAD MACHINE SCREWS THRU BOLT (6 PCS) END COVER MOUNTING BRACKET 1/4 x 1 1/4 (3 PCS) 1/4
More informationINSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET
HIGH EDGE 2 1/4"(57mm) 03079400070 INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET IMPORTANT: THIS LOCK IS NON-HANDED. LOCK IS FACTORY PACKED PREADJUSTED FOR 1³ ₄" (45mm)
More informationWOOD DOOR INSTALLATION
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-32VD9W TEMPLATE FOR VON DUPRIN 99 RIM WOOD DOOR INSTALLATION WHEN USING
More informationSMART ROUTING KIT. Sliding Arm. Perpendicular Stops* Control the movement along the Y-axis. Traveler Two slots for positioning on the Guide Rail
SMART ROUTING KIT The EZ SMART Smart Routing Kit (SRK) is the original routing kit for the EZ SMART system. It turns the average router into a production tool capable of multiple axis routing with CNC-like
More informationEntry Mortise Lock Set Lever to Lever
Entry Mortise Lock Set Lever to Lever 1 Lever 2 Escutcheon 3 Turn Piece 4 Mortise Lock 5 Scalp 6 Mortise Lock Strike 7 Mortise Lock Dust Box 8 Mortise Cylinder 9 Cylinder Swing Cover 10 Spindle 11 Spindle
More informationINSTRUCTIONS FOR HIT-41 SERIES ELECTRIC STRIKE TEMPLATES WHEN USING POWER TOOLS ALWAYS WEAR EYE AND EAR PROTECTION!!
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-41 SERIES ELECTRIC STRIKE TEMPLATES WHEN USING POWER TOOLS ALWAYS WEAR
More informationVYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4
VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7
More informationINSTRUCTIONS FOR HIT TEMPLATE FOR ALARM LOCK DL3500 MORTISE LOCK
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-210 TEMPLATE FOR ALARM LOCK DL3500 MORTISE LOCK WHEN USING POWER
More informationInstallation Manual Flat Track Series
Manual Flat Track Series Contents Safety...1 Parts...2 Hardware.......................................... 2 Tools Required..................................... 4.............................................
More informationCOMBINATION SLOT HEAD FIXTURE
COMBINATION SLOT HEAD FIXTURE This Combination slot head fixture is all you need in one tool! Its dual-sided, self centering design takes the guesswork out of headstocks alignment! No measuring required
More informationInstalling DoorSense August Smart Lock Pro
Installing DoorSense August Smart Lock Pro First, decide how you would like to install the DoorSense. August provides two options for installation: a surface mount and a flush mount installation. The surface
More informationINSTRUCTIONS FOR HIT TEMPLATE FOR SALTO XS-4 MORTISE & CYLINDRICAL LOCKS
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-268 TEMPLATE FOR SALTO XS-4 MORTISE & CYLINDRICAL LOCKS WHEN USING
More informationSALICE AIR TEMPLATE KIT
SALICE AIR TEMPLATE KIT There are two separate templates available for the machining of the AIR hinge; one is used for machining both the top and bottom of the door while the other is used for machining
More informationInstallation Instructions ED4400, ED4400M & ED4400MA Series Surface Vertical Rod Exit Devices
Installation Instructions ED4400, ED4400M & ED4400MA Series Surface Vertical Rod Exit Devices In U.S.: Corbin Russwin, Inc. 225 Episcopal Road Berlin, CT 06037 USA www.corbinrusswin.com In Canada: Door
More informationINSTRUCTIONS FOR HIT TEMPLATE FOR CYLINDRICAL LOCK PREPS
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-110 TEMPLATE FOR CYLINDRICAL LOCK PREPS WHEN USING POWER TOOLS ALWAYS
More informationInstallation Instructions for 45H & 47H Mortise Locks
Installation Instructions for 45H & 47H Mortise Locks Contents These installation instructions describe how to install your 45H & 47H Mortise Lock. Topics covered include: Finishing the preparation...
More informationSwingSafe Swing-Away Mailbox Support Diagram
SwingSafe Swing-Away Mailbox Support Diagram Wood Mounting Plates Top Arm (B) Muffler Clamps (A) Carriage Bolts and Nuts Bottom Arm 4-Foot U-Channel Post USPS Recommended 42-44 Height Ground Slope Hex
More informationInstallation Guide. Cue front unit (code and key) Cue rear unit (latch and bolt)
Installation Guide Cue front unit (code and key) Cue rear unit (latch and bolt) Before Lock Installation... 3 Surface Mount Installation For door thickness measuring between.01" -.91" (0.2 mm - 23 mm)...
More informationHIT-30 ALUMINUM DOOR SERIES OWNERS MANUAL
HIT-30 ALUMINUM DOOR SERIES OWNERS MANUAL INSTALL LOCKS LATCHES LEVERS / PADDLES INDICATORS STRIKES Every Installation Is A Self-Portrait Of The Person Who Did It! Autograph Your Work With Excellence!
More informationInstallation Instructions for 45HW & 47HW Electrified Mortise Locks
Installation Instructions for 45HW & 47HW Electrified Mortise Locks Contents These installation instructions describe how to install your 45HW & 47HW Electrified Mortise Lock. Topics covered include: Finishing
More informationOVERVIEW. Mounting Post (2 places) Cylinder Cam. Handing Pin
DEVICES COVERED IN THIS DOCUMENT: 46CE Cylinder Escutcheon Key locks and 46DT Dummy Trim Pull when dogged unlocks lever 46BE Blank Escutcheon Always operable 46NL Night Latch Key retracts latchbolt 46NK
More informationInstallation Instructions 50 (06-09) 1-15/32 15/32 21/32. 1/4-20 x 5/8" FHMS or #14 x 1/2" FHWS 1/16 1/4. Floor Plate
RIXSON ASSA ABLOY 3/4 Template Jamb 1/8 2- R. Max. 1-7/16 1-1/32 2-2-3/4 7/8 Dia. C L 1-1/4 Dia. Installation Instructions 50 (06-09) Finish Plate 340 TOP PIVOT Pivot Shown Engaged 9/16 1/16 1/4 1-15/32
More informationPassage Mortise Lock Set Lever to Lever
Passage Mortise Lock Set Lever to Lever 1 Lever 2 Escutcheon 3 Mortise Lock 4 Scalp 5 Mortise Lock Strike 6 Mortise Lock Dust Box 7 Spindle 8 Spindle Spring 9 Spindle Retainer 2 1 9 8 7 9 7 8 3 1 2 4 5
More information7110(F), 7170(F)(LBR) Surface Vertical Rod Exit Device Series Installation Instructions
7110(F), 7170(F)(LBR) Surface Vertical Rod Exit Device Series Installation Instructions Shim (2) Supplied Strike Plate 791 Strike (3) 10-24 x 3/4 (19mm) PFHMS Strike Angle Must Engage Strike 12-24 FHPMS
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More informationInstructions for Prepping an Opening for SOSS Invisible Hinges
Instructions for Prepping an Opening for SOSS Invisible Hinges IMPORTANT Use only Porter-Cable Template Guide Bushing #42024 (Lock Face Routing) and #42237 (Lock Nut) to assure the following guide bushing
More informationP USHbutton 500 series
Dimensions 35 60mm 178mm Model 500/505 For use with existing lock 1 6 2 7 3 8 4 9 5 0 1 6 2 7 3 8 4 9 5 0 Features ode Free Entry Mode by turning the slotted button 90 degrees after entering the code (models
More informationEvertune ET001F and ET001T Router Template Instructions
Evertune ET001F and ET001T Router Template Instructions 2011-05-05 All Templates: Every template has scribe lines for the guitar centerline and the scale length. Every template should be positioned so
More informationSWINGING SCREEN DOOR FIELD INSTALLATION INSTRUCTIONS
SWINGING SCREEN DOOR FIELD INSTALLATION INSTRUCTIONS TABLE OF CONTENTS 1: Measuring the Opening for the Storm Door... 4 2: Securing Storm Door Hinge Side Frame into Door Frame... 6 3: Securing Storm Door
More informationHinge Mortising Jig. One of the make it or break it parts of building a. 6 ShopNotes No. 74
Hinge Mortising Jig A Mortise for a Hinge. Quick, clean, and accurate that s the only way to describe the mortise you get with a trim router and this hinge mortising jig. One of the make it or break it
More informationBEST PRACTICE GUIDE. Socket Bases. Working with Concrete Slabs
Working with Concrete Slabs When working with concrete slabs the barrier protection can be erected in three ways - with socket bases, adjustable slab edge brackets and multi slab clamps. Socket Bases 1
More informationInstallers guide Deadbolt 02.
Installers guide Deadbolt 02. version 0.7.1 Specifications Model igloohome Smart Deadbolt 02 Material Zinc Alloy Current Rating (Standby) ~30uA Current Rating (Active) ~200mA Batteries 4 x AA Alkaline
More informationInstallation Instructions
Installation Instructions 8000/8300 Series Electric Strike Product Components HES, Inc. 22630 N. 17th Ave. Phoenix, AZ 85027 800-626-7590 www.hesinnovations.com 1 1 2 8000/8300 Electric Strike Body Sticky
More informationSCHLAGE SENSE. Smart Deadbolt. Installation Instructions. Download the Schlage Sense app to get started!
SCHLAGE SENSE Smart Deadbolt Installation Instructions Download the Schlage Sense app to get started! Schlage Sense Installation Instructions Package Contents Camelot Style shown throughout guide. Support
More informationInstallation Instructions 3040 (05-09) 9/16 9/ /32 9/32. Checking Adjustments
RIXSON ASSA ALOY Template 3/4 1/8 2- R. Max 1-7/16 1-1/32 2-2-3/4 7/8 Dia. C L Spindle Installation Instructions 3040 (05-09) 9/16 9/32 1/16 Finish Plate 1/4 1-1/4 Dia. 340 TOP PIVOT PIVOT SHOWN ENGAGED
More informationBefore Lock Installation Surface Mount Installation. Door Preparation. For door thickness measuring between.01" -.91" (0.2 mm - 23 mm)...
Installation Guide Before Lock Installation... 3 Surface Mount Installation For door thickness measuring between.01" -.91" (0.2 mm - 23 mm)... 4 Required Components... 4 Installation... 5 Door Preparation
More informationD3976 RECESSED EXIT INSTALLATION INSTRUCTIONS
PACKAGE CONTENTS PRODUCT MUST BE INSTALLED ACCORDING TO ALL APPLICABLE BUILDING AND LIFE SAFETY CODES TEMPLATE INSTALLATION INSTRUCTIONS STRIKE HAND TOOL 5/32 HEX KEY ROD END CAPS EXIT DEVICE CRANK ARM
More informationPreference Collection and Treatment Console INSTALLATION GUIDE
Preference Collection 5580.69 and 5580.96 Treatment Console INSTALLATION GUIDE WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious
More informationInstallation Instructions TK-2/3 and TKS-2/3
Installation Instructions TK-2/3 and TKS-2/3 The Trem King TKS-2 is designed to fit tele style guitars with a slanted bridge pickup mounted in the bridge plate. The TKS-2 has a Modern tele bridge footprint.
More information7210 Surface Vertical Rod Exit Device Installation Instructions. Outside Trim
7210 Surface Vertical Rod Exit Device Installation Instructions Top Mounting Plate (2) 1/4-20 x 3/4" PFHMS Blade Stop Block Shim (2 Supplied) Strike Plate 791 Strike (3) 10-24 x 1-1/4" PFHMS Top Latch
More informationAcoustical Surfaces, Inc.
RECEIVING 1. Immediately inspect shipment for damage during transit, for example: damage caused by fork lifts, stacking, water stains etc. and disclose to delivery driver prior to signing for receipt.
More information3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS
3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. TOOLS NEEDED: Tape Measure
More informationSide Light Frame Pack Assembly Instructions
Please read this complete set of assembly instructions before starting the installation and only when you understand the construction method start to follow the step by step guide. IDENTIFY THE PACK CONTENTS
More information33/3550AWDC. Fire-Rated Devices include these. additional. components. 1-Point Latch (LBL) Metal Edge Wrap required for 60 and 90-minute applications
24739476 33/3550AWDC nstallation nstructions 1-Point Latch (LBL) Fire-Rated Devices include these additional components Metal Edge Wrap required for 60 and 90-minute applications 2-Point Latch includes
More informationNARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE. Installation Instructions
NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE Installation Instructions PART Y015 JUNE 2016 Table of Contents Section 1. GENERAL NOTES AND GUIDELINES... 2. DOOR HARDWARE A. Locks B. Push/Pulls
More informationFretboard Wednesday, January 16, :36 PM
ASL Breakdown Page 1 Fretboard Wednesday, January 16, 2013 9:36 PM - - To prepare the fretboard for cutting fret slots: True one edge of the fretboard blank on the jointer. True one of the other edges
More informationSeries----SP3600A SHOWER DOOR
Series----SP3600A SHOWER DOOR INSTALLATION INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram
More informationTools Required. * When installing on a fire door, please see instructions below. *
CL615 Tubular Mortice Latch with Code Free option CL615 Tubular Mortice Latch with Code Free option Number relating to picture Item 1 Front Plate and handle * 2 Back Plate and handle * 3 Neoprene seals
More informationSide Light Frame Pack Assembly Instructions
Side Light Frame Pack Assembly Instructions Please read this complete set of assembly instructions before starting the installation and only when you understand the construction method start to follow
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PARTS REQUIRED Single QuickStand Lite Parts A (1) Lower Arm A B C D B (1) Upper Arm C (1) Base D (1) Base Plate E (1) M8 Dynamic Arm Long F (1) Clamp Bracket G H (1) VESA Plate
More informationPreference Slimline 5536 Utility Console
Preference Slimline 5536 Utility Console I NSTALLATION GUIDE WARNING Failure to install the 5536 as described in this installation guide may cause the unit to collapse, resulting in serious injury to personnel.
More informationESA-200 Fixed Sidelite
Exterior View Installation Instructions For use with ESA II Controller 1 Tools Required: Suggested Fasteners Required - (Not supplied) Screwdrivers Small Straight (FlatBlade) - for Terminal Block wiring
More informationESA-100 Fixed Sidelite/Non Breakout
/Non Breakout Exterior View Installation Instructions For use with ESA II Controller 1 Tools Required: Suggested Fasteners Required - (Not supplied) Screwdrivers Small Straight (FlatBlade) - for Terminal
More informationWINDLOAD POST WayneMark 8000, 8100 INSTALLATION INSTRUCTIONS
WINDLOAD POST WayneMark 8000, 8100 INSTALLATION INSTRUCTIONS Wayne Dalton, a division of Overhead Door Corporation P.O. Box 67, Mt. Hope, OH 44660 www.wayne-dalton.com See garage door owner s manual for
More information1200 SERIES 2 PANEL DOOR rev.1 DETAILED INSTALLATION INTRUCTIONS
1200 SERIES 2 PANEL DOOR 10.2013 rev.1 DETAILED INSTALLATION INTRUCTIONS GENERAL: Door elevations shown in these instructions are as viewed from the outside. X denotes the active or moving panel(s). O
More informationTOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill
DEVICES COVERED IN THIS DOCUMENT: 4700S Surface Vertical Rod Device 4700SF Fire Exit Surface Vertical Rod Device TOOLS REQUIRED Metal Wood Wood and Metal Screws Sex Bolts #7 Drill ¼ -20 Tap #16 Drill #12-24
More informationCL4500 Installation Instructions
CL4500 Installation Instructions Box Contents Check the contents of the box are correct according to the model 4510 4520 1 Front Plate 2 Back Plate 3 Lever Handles 4 Gaskets 5 Sprung Spindle (x1) 6 Spring
More informationsmart hot runner solutions
smart hot runner solutions www.mastip.com Assembly Overview System Overview 1. IMPORTANT!! High temperature (ºC) air fittings and line must be used on this nozzle. The cylinder should be in the closed
More informationEndura All-Aluminum Z-Articulating Cap Sill Retrofit Kit for French Doors
Endura All-Aluminum Z-Articulating Cap Sill Retrofit Kit for French Doors Installation Instructions Before You Begin: This retrofit kit is designed for the Endura Z-Series All- Aluminum sill. Please ensure
More informationVersatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series
Versatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series TM Rough opening width (finished opening width plus 9/16") Notch for top track units (used as frame header) Rough opening height
More informationEnd of Row Doors. Revision Number 1
End of Row Doors Single Swing Door Café Style Doors Revision Number 1 Wright Line LLC 160 Gold Star Boulevard Worcester, MA 01606 Tel: 800-225-7348 508-852-4300 Fax: 508-365-6178 www.wrightline.com info@wrightline.com
More informationModel 6100 Illustrated Installation Instructions Contractors Wardrobe
Model 6100 Illustrated Installation Instructions Contractors Wardrobe DESIGNERS MANUFACTURERS 26121 Avenue Hall Valencia, CA 91355 (661) 257-17 Fax: (661) 257-4907 Toll Free: (800) CW-DOORS (800) 293-6677
More informationNotification System Installation Guide
Notification System Installation Guide NOTE: It is strongly recommend that you hire a licensed electrician to perform the installation of this product. Materials Provided 1. Directory Sign (1) a. Directory
More informationCustom Wood Frame Overlay for Glass Doors Installation Instructions
MARVEL CUSTOM WOOD FRAME OVERLAY FOR GLASS DOORS Custom Wood Frame Overlay for Glass Doors Installation Instructions Wine Cellars 6SWC 6SWCE 61WC 61WCM 66SWC (2 required) 66SWCE (2 required) Beverage Centers
More informationINSTRUCTIONS FOR HIT TEMPLATE FOR BEST 34H-37H MORTISE LOCK
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-230 TEMPLATE FOR BEST 34H-37H MORTISE LOCK WHEN USING POWER TOOLS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS ANSI/BHMA - A156.2 BOX CONTENTS CHECK THAT THE CONTENTS OF YOUR BOX ARE CORRECT ACCORDING TO THE MODEL Model 600/605 Model 610/615 Model 620/625 1 Front plate and handle 2 Back
More information98/ Customer Service # Dogging Key (use to lock down pushbar)
911373-00 Rim Exit Device 98/99 Installation Instructions Dogging Key (use to lock down pushbar) Customer Service 1-877-671-7011 www.allegion.com/us Allegion 2014 Printed in U.S.A. 911373-00 Rev. 05/14-f
More informationCrossOver X25 Lock Installation Need another copy of these installation sheets? You can download one at
CrossOver X25 Lock Installation Need another copy of these installation sheets? You can download one at www.crossoverlock.com/supportcenter.htm 1 Back view of installation Major lock parts 1. Rear handle
More informationVanity Installation Instructions
Vanity Installation Instructions Segments of these instructions will relate to your vanity. Please read these instructions thoroughly and ensure the appropriate instructions are used during the installation
More informationCMT Enlock Jig Owner s Manual
Thank you for purchasing the CMT Enlock Jig. This jig will simplify joinery in your shop, and on the job site. Please read the instructions thoroughly before using the Enlock Jig. Router requirements A
More informationPreference Collection 5580 Treatment Console INSTALLATION GUIDE
Preference Collection 5580 Treatment Console INSTALLATION GUIDE 0 WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious injury
More informationINSTALLATION INSTRUCTIONS. UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE
INSTALLATION INSTRUCTIONS UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE QCI0011 Rev. 0 Page 1of 10 Certified 10/18/2006 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure;
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationUltimate Trilennium Astragal Prehanger Installation Instructions
Ultimte Trilennium Astrgl Prehnger Instlltion Instructions Tools Required: Flthed Screwdriver Shers Phillips Screwdriver Power Drill with 1" Drill Bit Tpe Mesure 1" Spde Bit Kit Includes: Full Astrgl Full
More informationPRODUCT: LOKI INSTALLATION INSTRUCTIONS. Product is covered by U.S. patents. For more information visit
R INSTALLATION INSTRUCTIONS PRODUCT: LOKI CONFIGURATION: SINGLE DOOR MOUNT: GLASS MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com . TOOLS + MATERIALS REQUIRED TOOLS
More informationHigh Density Sports Storage
Owner s Manual High Density Sports Storage CONTENTS Safety...........................................2 General......................................2 Installation...................................2 Usage.......................................2
More informationSLIDING GLASS DOOR ASSEMBLY INSTRUCTION Series 680/780
10/07 M0200030 GENERAL NOTICE READING THESE INSTRUCTIONS FIRST AND FOLLOWING THE PROCEDURES IN PROPER SEQUENCE WILL REDUCE FRUSTRATION, COSTLY MISTAKES AND WASTED TIME. Protect main frame only with light
More informationVigilant Cigar Humidor Vault. Assembly Instructions
Vigilant Cigar Humidor Vault Assembly Instructions Models: 1000, 1500, and 2000 Congratulations! You have purchased a superior cigar humidor. These humidors have been specifically designed to properly
More informationINSTALLING YOUR NEW SPRING LIFT ARM KIT
INSTALLING YOUR NEW SPRING LIFT ARM KIT 1. Measure the distance that the roof is to be raised. [If your lift system is completely non-functional, you will need to calculate or estimate this distance as
More informationINSTRUCTIONS FOR HIT TEMPLATE FOR SCHLAGE AD MORTISE LOCK
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-280 TEMPLATE FOR SCHLAGE AD MORTISE LOCK WHEN USING POWER TOOLS ALWAYS
More information