Model House Exercise-( Extrude)
|
|
|
- Horace Brooks
- 5 years ago
- Views:
Transcription
1 -( Extrude) Prerequisite knowledge Focus of the lesson Commands Used This lesson requires an understanding of using the sketch commands including Inserting a new sketch Adding sketch geometry Understanding the state of the sketch Smart Dimension, Trim, Mirror and Shell This exercise will develop your ability to, select the best profile (the one, when extruded, will generate more of the model than any other) select the best plane on which to place the sketch select the best end condition when using the extrude command On completion of this lesson you will have used Sketch, Mirror, Trim, Extruded Boss/Base, Shell and Extruded Cut DCG/Ex Design &Communication Graphics 1
2 Getting Started When the geometry of this Model House is analysed, it becomes apparent that the main body and roof can be extruded from the right plane, the front entrance off the front plane and the chimney off the top plane. The first feature of the part to be created is the body of the house. This will be an extruded feature based on a sketch. Create a sketch on the right plane similar to the following one. Position the sketch so that the origin is in the lower right hand corner. Note that the line on the right is drawn using the centerline command. Using Mirror Entities, select the lines to be mirrored and the centre line about which they are mirrored. Smart dimension the sketch as shown. DCG/Ex Design &Communication Graphics 2
3 Select Extruded Boss/Base. Select the Mid Plane end condition from the list and enter a width of 160mm. The Mid Plane option is the most appropriate in this exercise as it can be used to create the body, the roof and protruding side windows from a single sketch plane. Renaming the Feature Select the name of the feature (Extrude 1). Press F2 On the keyboard and type the new name of the feature (Body) This allows us to rename each completed feature which makes it easier to identify/ edit different parts on a completed part drawing. DCG/Ex Design &Communication Graphics 3
4 Roofing the house Select the Right Plane from the Feature Manager Design Tree. View Normal To and ` create a sketch using dimensions shown. ` Note the location of the sketch in relation to `. the top of the previous one. Select Extruded Boss/Base. Select the Mid Plane end condition from the list and enter a width of 170mm. and rename the feature. (Body) Note the manner in which this gives an overhang of 5mm on each side. DCG/Ex Design &Communication Graphics 4
5 Side Windows Create a sketch on the right plane using the dimensions shown. Note the location of the origin. Use Trim Entities to remove the lower half of the circle. Select Extrude Boss/Base. Select Offset From surface. Select the face you want to offset from and enter a distance of 20mm. Use the Reverse Offset to ensure the offset is in the correct direction. The Offset From Surface command. ensures that if the length of the house is changed the offset remains at 20mm. Select the Direction 2 box to expand the window. Select the second face you want to offset from and enter a value of 20mm. Use the Reverse Direction to ensure the offset is in the correct direction. and rename the feature. (Side Windows) DCG/Ex Design &Communication Graphics 5
6 Front Entrance Create a sketch on the front plane using the dimensions shown. Note the location of the origin in the centre of the base and how the centre of the semi-circle has the same altitude as the base edge of the roof. Using Extrude Boss/Base and Offset From Surface as in the previous page, set the distance at 25mm to create the feature. and rename the feature. (Entrance) Chimney Create a sketch on the top plane using the dimensions shown. The centre of the square is on the ridge line of the roof. (Using Mirror Entities as outlined on page 2 is one option in creating this sketch.) DCG/Ex Design &Communication Graphics 6
7 Using Extrude Boss/Base and the Blind end condition, set the distance at 120mm. and rename the feature. (Chimney) Changing the altitude of the house will require a similar change in this feature to maintain the overall appearance. Future lessons will deal with the use of inserted sketch planes and how they can help overcome this problem. Creating the shell On the features toolbar click the shell tool. Select the base of the house and set the distance at 5mm. (To select the base we need to see it. To achieve this, hold down the mouse wheel and move the mouse to rotate the drawing) and rename the feature. (Shell) DCG/Ex Design &Communication Graphics 7
8 This completes the shell with a 5mm wall thickness. Windows and Doors Create a sketch on the front plane using the dimensions shown. Select the plane and view normal to as previously outlined.note the use of centerline command as used in page 2. Using Mirror Entities from the features toolbar, create the right hand side of the sketch. DCG/Ex Design &Communication Graphics 8
9 Use the 3 point arc from the sketch toolbar to complete the sketch using the dimensions shown. To create the arc, select one end, select the other end and then select the approximate location of the top of the curve. Select Extrude Cut from the features toolbar. Select the Up To Surface end condition and the front face of the entrance as the chosen surface. and rename the feature. (Front opes) Using the Up To Surface end condition ensures that any changes in the width of the house will not change these openings. DCG/Ex Design &Communication Graphics 9
10 Side Windows Create a sketch on the selected plane using the dimensions shown. Note the concentric circles. Select Extrude cut from the features toolbar and use the Through All end condition. (Side opes) and rename the feature. Using the Through All end condition ensures that any change in the width of the house will not change these openings. DCG/Ex Design &Communication Graphics 10
11 Edit Material Right click on Roof in the Feature Manager Design Tree, select Appearance, Texture.. Select Stone..Slate Edit Colour Right click on Body, Side Windows, Entrance etc. in the Feature Manager Design Tree, select Appearance, Colour.and select a colour to make the model look more realistic as shown on the front page of the document. DCG/Ex Design &Communication Graphics 11
12 Alternative Option In this case Revolve Boss/Base can be selected from the Features toolbar to create the tower. Lofted Boss/Base Conical top surface. can also be used to create the Lesson Complete!. DCG/Ex Design &Communication Graphics 12
Introduction to Circular Pattern Flower Pot
Prerequisite Knowledge Previous knowledge of the sketching commands Line, Circle, Add Relations, Smart Dimension is required to complete this lesson. Previous examples of Revolved Boss/Base, Cut Extrude,
Clock Exercise (Inserting Planes)
Clock Exercise (Inserting Planes) Prerequisite Knowledge To complete this exercise you will need to be familiar with Sketching, Applying relations, Extrude Boss/ Base, Extrude cut, Applying Textures, Renaming
10/14/2010. Chevy Malibu. Vehicle Design with Solidworks. Start SolidWorks Create a New SolidWorks Document. Miles, Rowardo B
Chevy Malibu Vehicle Design with Solidworks Start SolidWorks Create a New SolidWorks Document Miles, Rowardo B 1 Click: Part and then OK Now you are ready to make a Part. 2 Right Toolbar: Document Properties:
Introduction to Revolve - A Glass
Introduction to Revolve - A Glass Design & Communication Graphics 1 Object Analysis sheet Design & Communication Graphics 2 Prerequisite Knowledge Previous knowledge of the following commands are required
From the above fig. After sketching the path and profile select the sweep command First select the profile from property manager tree And then select
Chapter 5 In sweep command there is a) Two sketch profiles b) Two path c) One sketch profile and one path The sweep profile is used to create threads springs circular things and difficult geometry. For
Digital Camera Exercise
Commands Used New Part This lesson includes Sketching, Extruded Boss/Base, Extruded Cut, Fillet, Chamfer and Text. Click File, New on the standard toolbar. Select Part from the New SolidWorks Document
SolidWorks Navigation
SolidWorks Basics SolidWorks Navigation Command Bar Feature Tree Model Window Simple Box Select the Front plane Create a new sketch Create a Center Rectangle from the origin Smart Dimension the length
Wireless Mouse Surfaces
Wireless Mouse Surfaces Design & Communication Graphics Table of Contents Table of Contents... 1 Introduction 2 Mouse Body. 3 Edge Cut.12 Centre Cut....14 Wheel Opening.. 15 Wheel Location.. 16 Laser..
Purlin Roof. Create a New Folder in your chosen location called Purlin Roof. The nine parts that make up the project will be saved here.
Purlin Roof Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Add Relations, Dimensioning), Inserting Planes, Extrude,
Spatula. Spatula SW 2015 Design & Communication Graphics Page 1
Spatula Introduction: The model shown in the picture is made of three parts, - the base, the washer and the handle. The base requires the use of Spline and Style Spline command, Slot command and Mirror
Sash Clamp. Sash Clamp SW 2015 Design & Communication Graphics Page 1.
Sash Clamp 1 Introduction: The Sash clamp consists of nine parts. In creating the clamp we will be looking at the improvements made by SolidWorks in linear patterns, adding threads and in assembling the
AEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here.
AEROPLANE Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Arc, Add Relations, Dimensioning), Extrude, Assemblies and
SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI
SolidWorks 2015 Part I - Basic Tools Includes CSWA Preparation Material Parts, Assemblies and Drawings Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered
Engineering Technology
Engineering Technology Introduction to Parametric Modelling Engineering Technology 1 See Saw Exercise Part 1 Base Commands used New Part This lesson includes Sketching, Extruded Boss/Base, Hole Wizard,
SolidWorks Design & Technology
SolidWorks Design & Technology Training Course at PHSG Ex 5. Lego man Working with part files 8mm At first glance the Lego man looks complicated but I hope you will see that if you approach a project one
EXERCISE ONE: BEACH BUGGY.
EXERCISE ONE: BEACH BUGGY. Prerequisite knowledge Students should have completed Exercises from the file: Introduction to Assemblies Concept Mates Focus of lesson Commands Used This lesson will focus on
Hydro Hull. Chapter 21. Boat. A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2).
Chapter 21 Boat Hydro Hull A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2). Step 2. Click File Menu > Save As. Step 3. Key-in HYDRO for the filename and press ENTER. B. Delete Loft1,
Introduction to Sweep - Allen Key part (A)
Introduction to Sweep - Allen Key part (A) Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson, sketching (line construction, dimensioning, polygon).
Toothbrush Holder. A drawing of the sheet metal part will also be created.
Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson; Sketch (Line, Centerline, Circle, Add Relations, Smart Dimension,), Extrude Boss/Base, and Edit
Beginner s Guide to SolidWorks Level I
Beginner s Guide to SolidWorks 2013 - Level I Parts, Assemblies, Drawings, Simulation Xpress Alejandro Reyes MSME, CSWP, CSWI SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices.
Engineering & Computer Graphics Workbook Using SolidWorks 2014
Engineering & Computer Graphics Workbook Using SolidWorks 2014 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)
Beginner s Guide to SolidWorks Level I
Beginner s Guide to SolidWorks 2014 - Level I Parts, Assemblies, Drawings, PhotoView 360 and Simulation Xpress Videos Now includes SolidWorks training videos Alejandro Reyes MSME, CSWP, CSWI Multimedia
Engineering & Computer Graphics Workbook Using SOLIDWORKS
Engineering & Computer Graphics Workbook Using SOLIDWORKS 2017 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)
DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY
DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY CAPSULE PROGRAM Funded by NSF grant #0833636 Tutorial 02 3D Part Modeling SolidWorks 2010 Copyright 2010 Prof. Zeid 3D Part Modeling
Introducing SolidWorks
Introducing SolidWorks SAAST Robotics 2008 SolidWorks Software Visually-based 3-D Mechanical design software Engineers and Designers use it to: Quickly sketch out ideas Experiment with features, dimensions
Product Modelling in Solid Works
Product Modelling in Solid Works In the following exercise you will use solid works to construct the computer mouse shown opposite. In this exercise you will use a number of advanced features to achieve
g. Click once on the left vertical line of the rectangle.
This drawing will require you to a model of a truck as a Solidworks Part. Please be sure to read the directions carefully before constructing the truck in Solidworks. Before submitting you will be required
Alternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch.
Sketcher All feature creation begins with two-dimensional drawing in the sketcher and then adding the third dimension in some way. The sketcher has many menus to help create various types of sketches.
Introduction to Sheet Metal Features SolidWorks 2009
SolidWorks 2009 Table of Contents Introduction to Sheet Metal Features Base Flange Method Magazine File.. 3 Envelopment & Development of Surfaces.. 14 Development of Transition Pieces.. 23 Conversion to
Feature-Based Modeling and Optional Advanced Modeling. ENGR 1182 SolidWorks 05
Feature-Based Modeling and Optional Advanced Modeling ENGR 1182 SolidWorks 05 Today s Objectives Feature-Based Modeling (comprised of 2 sections as shown below) 1. Breaking it down into features Creating
Chair. Bottom Rail. on the Command Manager. on the Weldments toolbar.
Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click
SOLIDWORKS Essentials
SOLIDWORKS Essentials Length: 5 days Prerequisite: Mechanical design experience and experience with the Windows operating system. Description: SOLIDWORKS Essentials teaches you how to use SOLIDWORKS mechanical
CAD Tutorial 24: Step by Step Guide
CAD TUTORIAL 24: Step by step CAD Tutorial 24: Step by Step Guide Level of Difficulty Time Approximately 40 50 minutes Lesson Objectives To understand the basic tools used in SketchUp. To understand the
Bottom Rail. Chapter 2. Chair. A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. B. 3D Sketch.
Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click
SolidWorks Reference Geometry
SolidWorks Reference Geometry IDeATe Laser Micro Part 2 Dave Touretzky and Susan Finger 1. Symmetry and Reference Geometry Today, you ll make this part bear-like face and then cut it on the laser cutter:
Shaft Hanger - SolidWorks
ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN Shaft Hanger - SolidWorks BY: DR. HERLI SURJANHATA ASSIGNMENT Submit TWO isometric views of the Shaft Hanger with your report, 1. Shaded view of the trimetric
Explanation of buttons used for sketching in Unigraphics
Explanation of buttons used for sketching in Unigraphics Sketcher Tool Bar Finish Sketch is for exiting the Sketcher Task Environment. Sketch Name is the name of the current active sketch. You can also
SolidWorks 95 User s Guide
SolidWorks 95 User s Guide Disclaimer: The following User Guide was extracted from SolidWorks 95 Help files and was not originally distributed in this format. All content 1995, SolidWorks Corporation Contents
Cube in a cube Fusion 360 tutorial
Cube in a cube Fusion 360 tutorial n Before using these instructions, it is helpful to watch this video screencast of the CAD drawing actually being done in the software. Click to link to the video tutorial.
for Solidworks TRAINING GUIDE LESSON-9-CAD
for Solidworks TRAINING GUIDE LESSON-9-CAD Mastercam for SolidWorks Training Guide Objectives You will create the geometry for SolidWorks-Lesson-9 using SolidWorks 3D CAD software. You will be working
SDC. SolidWorks Tutorial 2001Plus. A Competency Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P.
2001Plus A Competency Project Based Approach Utilizing 3D Solid Modeling David C. Planchard & Marie P. Planchard SDC PUBLICATIONS www.schroff.com www.schroff-europe.com Project 2 Below are the desired
Drawing and Assembling
Youth Explore Trades Skills Description In this activity the six sides of a die will be drawn and then assembled together. The intent is to understand how constraints are used to lock individual parts
Lesson 10: Loft Features
10 Goals of This Lesson Your students will be able to create the following part: profiles chisel This lesson plan corresponds to the Loft Features chapter of SolidWorks Getting Started. SolidWorks Student
Essentials of SOLIDWORKS 2015 (4+ Days) * Ve-I Bonus! * File Management + SimulationXpress
Essentials of SOLIDWORKS 2015 (4+ Days) * Ve-I Bonus! * File Management + SimulationXpress Overview What is SOLIDWORKS? Interface Tour View Manipulation Provides some background info on the SOLIDWORKS
Lab 3 Introduction to SolidWorks I Silas Bernardoni 10/9/2008
1 Introduction This lab is designed to provide you with basic skills when using the 3D modeling program SolidWorks. You will learn how to build parts, assemblies and drawings. You will be given a physical
Computer Aided Design Module 2. Lesson Toblerone Bar
Computer Aided Design Module 2 Lesson Toblerone Bar Lesson? Toblerone Bar New Commands used: Polygon, Add Relations, Smart Dimension, Extrude Boss/Base (Mid Plane), Fillet, Line, Extrude-Cut, Linear Pattern
Beginner s Guide to SolidWorks Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS
Beginner s Guide to SolidWorks 2008 Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com Part Modeling
EN1740 Computer Aided Visualization and Design Spring /1/2012 Brian C. P. Burke
EN1740 Computer Aided Visualization and Design Spring 2012 3/1/2012 Brian C. P. Burke Last time: Measure Shell Surfaces Best practices/appropriate Uses Parametric From standard features Tonight: Finish
Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated)
Inventor (5) Module 2: 2-1 Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated) In this tutorial, we will learn how to build a 3D model
1. Creating geometry based on sketches 2. Using sketch lines as reference 3. Using sketches to drive changes in geometry
4.1: Modeling 3D Modeling is a key process of getting your ideas from a concept to a read- for- manufacture state, making it core foundation of the product development process. In Fusion 360, there are
TRAINING COURSE PROSPECTUS
SOLIDWORKS Essentials Duration: Prerequisites: Description: The topics covered in this course are: 4 Days Mechanical design experience; experience with the Windows operating system SOLIDWORKS Essentials
Introduction to 3D CAD with SolidWorks. Jianan Li
Introduction to 3D CAD with SolidWorks Jianan Li Create a New Part The first time you launch SolidWorks, it asks you to set the default units and dimension standard. Make sure you have IPS and ANSI selected,
Part 8: The Front Cover
Part 8: The Front Cover 4 Earpiece cuts and housing Lens cut and housing Microphone cut and housing The front cover is similar to the back cover in that it is a shelled protrusion with screw posts extruding
Objectives. Inventor Part Modeling MA 23-1 Presented by Tom Short, P.E. Munro & Associates, Inc
Objectives Inventor Part Modeling MA 23-1 Presented by Tom Short, P.E. Munro & Associates, Inc To demonstrate most of the sketch tools and part features in : Inventor Release 6 And, to show logical techniques
Using Google SketchUp
Using Google SketchUp Opening sketchup 1. From the program menu click on the SketchUp 8 folder and select 3. From the Template Selection select Architectural Design Millimeters. 2. The Welcome to SketchUp
CREO.1 MODELING A BELT WHEEL
CREO.1 MODELING A BELT WHEEL Figure 1: A belt wheel modeled in this exercise. Learning Targets In this exercise you will learn: Using symmetry when sketching Using pattern to copy features Using RMB when
SolidWorks Tutorial 1. Axis
SolidWorks Tutorial 1 Axis Axis This first exercise provides an introduction to SolidWorks software. First, we will design and draw a simple part: an axis with different diameters. You will learn how to
Understanding Projection Systems
Understanding Projection Systems A Point: A point has no dimensions, a theoretical location that has neither length, width nor height. A point shows an exact location in space. It is important to understand
1. Open the Feature Modeling demo part file on the EEIC website. Ask student about which constraints needed to Fully Define.
BLUE boxed notes are intended as aids to the lecturer RED boxed notes are comments that the lecturer could make Control + Click HERE to view enlarged IMAGE and Construction Strategy he following set of
Solidworks Tutorial Pencil
The following instructions will be used to help you create a Pencil using Solidworks. These instructions are ordered to make the process as simple as possible. Deviating from the order, or not following
SolidWorks 103: Barge Design Challenge
SolidWorks 103: Barge Design Challenge Note: This tutorial was created using SolidWorks 2009. If you are using another version of SolidWorks, you may notice some variation in display states and configuration.
Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material
ENGINEERING & COMPUTER GRAPHICS WORKBOOK Using SolidWorks 2005 Ronald E. Barr Thomas J. Krueger Theodore A. Aanstoos Davor Juricic SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com
WEEK 5: Shaft Modeling (C51X01, C51X02) Revolved Features, Chamfer
WEEK 5: Shaft Modeling (C51X01, C51X02) Revolved Features, Chamfer 1. Creating the Shaft Model 1. File> New> Part, Name: C51X01> OK 2. Insert> Revolve> Placement> Define> select TOP datum plane> Sketch
Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material
ENGINEERING & COMPUTER GRAPHICS WORKBOOK Using SolidWorks 2008 Ronald E. Barr Thomas J. Krueger Theodore A. Aanstoos Davor Juricic SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better
Rotational Patterns of Sketched Features Using Datum Planes On-The-Fly
Rotational Patterns of Sketched Features Using Datum Planes On-The-Fly Patterning a sketched feature (such as a slot, rib, square, etc.,) requires a slightly different technique. Why can t we create a
Using Siemens NX 11 Software. The connecting rod
Using Siemens NX 11 Software The connecting rod Based on a Catia tutorial written by Loïc Stefanski. At the end of this manual, you should obtain the following part: 1 Introduction. Start NX 11 and open
Introduction to SolidWorks Introduction to SolidWorks
Introduction to SolidWorks Introduction to SolidWorks SolidWorks is a powerful 3D modeling program. The models it produces can be used in a number of ways to simulate the behaviour of a real part or assembly
Part Design. Sketcher - Basic 1 13,0600,1488,1586(SP6)
Part Design Sketcher - Basic 1 13,0600,1488,1586(SP6) In this exercise, we will learn the foundation of the Sketcher and its basic functions. The Sketcher is a tool used to create two-dimensional (2D)
Inventor 2016 Essentials Plus
Autodesk NEW Features a chapter on sheet metal design Inventor 2016 Essentials Plus Daniel T. Banach & Travis Jones SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF
Autodesk Inventor Module 17 Angles
Inventor Self-paced ecourse Autodesk Inventor Module 17 Angles Learning Outcomes When you have completed this module, you will be able to: 1 Describe drawing inclined lines, aligned and angular dimensions,
Veerapandian.K Mechanical Engg Vedharanyam A manual to mechanical designers How Solid works Works?
Compiled by Veerapandian.K Mechanical Engg Vedharanyam-614 810 A manual to mechanical designers How Solid works Works? Solid works Overview Solid works main idea is user to create drawing directly in 3D
Introduction to Autodesk Inventor for F1 in Schools (Australian Version)
Introduction to Autodesk Inventor for F1 in Schools (Australian Version) F1 in Schools race car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital
CATIA Instructor-led Live Online Training Program
Course Outline Introduction & Understanding to CATIA Environment Introduction & Understanding to CATIA interface Starting new file Understand the Sketcher workbench of CATIA V5 Start a new file in the
Creo Parametric 4.0 Basic Design
Creo Parametric 4.0 Basic Design Contents Table of Contents Introduction...1 Objective of This Textbook...1 Textbook Outline...2 Textbook Conventions...3 Exercise Files...3 System Configuration...4 Notes
Advance Dimensioning and Base Feature Options
Chapter 4 Advance Dimensioning and Base Feature Options Learning Objectives After completing this chapter you will be able to: Dimension the sketch using the autodimension sketch tool. Dimension the sketch
Siemens NX11 tutorials. The angled part
Siemens NX11 tutorials The angled part Adaptation to NX 11 from notes from a seminar Drive-to-trial organized by IBM and GDTech. This tutorial will help you design the mechanical presented in the figure
Introduction to solid modeling using Onshape
Onshape is a CAD/solid modeling application. It provides powerful parametric and direct modeling capabilities. It is cloud based therefore you do not need to install any software. Documents are shareable.
Module 2.1, 2.2 Review. EF101 Analysis & Skills Module 2.3. Sketched Features and Operations. On-line Help Two Locations
EF101 Analysis & Skills Module 2.3 Engineering Graphics Revolved Features Placed Features Work Features Module 2.1, 2.2 Review What are the three types of operations for adding features to the base feature?
Lesson 6 2D Sketch Panel Tools
Lesson 6 2D Sketch Panel Tools Inventor s Sketch Tool Bar contains tools for creating the basic geometry to create features and parts. On the surface, the Geometry tools look fairly standard: line, circle,
The Revolve Feature and Assembly Modeling
The Revolve Feature and Assembly Modeling PTC Clock Page 52 PTC Contents Introduction... 54 The Revolve Feature... 55 Creating a revolved feature...57 Creating face details... 58 Using Text... 61 Assembling
Creo Revolve Tutorial
Creo Revolve Tutorial Setup 1. Open Creo Parametric Note: Refer back to the Creo Extrude Tutorial for references and screen shots of the Creo layout 2. Set Working Directory a. From the Model Tree navigate
Creo Parametric 2.0: Introduction to Solid Modeling. Creo Parametric 2.0: Introduction to Solid Modeling
Creo Parametric 2.0: Introduction to Solid Modeling 1 2 Part 1 Class Files... xiii Chapter 1 Introduction to Creo Parametric... 1-1 1.1 Solid Modeling... 1-4 1.2 Creo Parametric Fundamentals... 1-6 Feature-Based...
Education Curriculum Combined Specialist
Education Curriculum Combined Specialist Invest your time in imagining next generation designs. Here s what we will teach you to give shape to your imagination. CATIA Combined Specialist Course CATIA Mechanical
SOLIDWORKS 2016 Advanced Techniques
SOLIDWORKS 2016 Advanced Techniques Mastering Parts, Surfaces, Sheet Metal, SimulationXpress, Top Down Assemblies, Core & Cavity Molds Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices.
Introduction to Autodesk Inventor User Interface Student Manual MODEL WINDOW
Emmett Wemp EDTECH 503 Introduction to Autodesk Inventor User Interface Fill in the blanks of the different tools available in the user interface of Autodesk Inventor as your instructor discusses them.
SOLIDWORKS 2015 and Engineering Graphics
SOLIDWORKS 2015 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following
Lesson 4 Extrusions OBJECTIVES. Extrusions
Lesson 4 Extrusions Figure 4.1 Clamp OBJECTIVES Create a feature using an Extruded protrusion Understand Setup and Environment settings Define and set a Material type Create and use Datum features Sketch
SolidWize. Online SolidWorks Training. Simple Sweep: Head Scratcher
SolidWize Online SolidWorks Training Simple Sweep: Head Scratcher Step 1: Creating the Handle: Sketch Using Inches as the unit create a sketch on the Front plane. Start with the sketch shown below: Create
Lab 1: Engineering Drawing, 3D Printing and Laser Cutting Innovation Fellows Program Bootcamp Prof. Steven S. Saliterman
Lab 1: Engineering Drawing, 3D Printing and Laser Cutting Innovation Fellows Program Bootcamp Prof. Steven S. Saliterman In the following exercises you will learn basic drawing skills required for most
Below are the desired outcomes and usage competencies based on the completion of Project 4.
Engineering Design with SolidWorks Project 4 Below are the desired outcomes and usage competencies based on the completion of Project 4. Project Desired Outcomes: An understanding of the customer s requirements
Parametric Modeling. with. Autodesk Inventor Randy H. Shih. Oregon Institute of Technology SDC
Parametric Modeling with Autodesk Inventor 2009 Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower Prices. iii Table of
Inventor Activity 5: Lofted Vase
Inventor Activity 5: Lofted Vase In this tutorial, you will use a few new commands to create a free form Lofted object. Sometimes you want to create an object that is not made up of square, flat, or perfectly
1.6.7 Add Arc Length Dimension Modify Dimension Value Check the Sketch Curve Connectivity
Contents 2D Sketch... 1 1.1 2D Sketch Introduction... 1 1.1.1 2D Sketch... 1 1.1.2 Basic Setting of 2D Sketch... 2 1.1.3 Exit 2D Sketch... 4 1.2 Draw Common Geometry... 5 2.2.1 Points... 5 2.2.2 Lines
Drawing a Living Room and Family Room Floorplan
Appendix C Drawing a Living Room and Family Room Floorplan In this chapter, you will learn the following to World Class standards: Draw a Living Room and Family Room Floorplan Draw the Walls and Stairs
Introduction to CATIA V5
Introduction to CATIA V5 Release 17 (A Hands-On Tutorial Approach) Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower
Canoe Mirroring Lofts
Canoe Mirroring Lofts 1. Set Units to Inches 2. Create a New Design. 3. Save the Design as canoeinl811 in your Canoe folder. 4. Create a New Sketch on the Frontal Workplane. Name the Sketch Middle. 5.
Revit Structure 2014 Basics
Revit Structure 2014 Basics Framing and Documentation Elise Moss Authorized Author SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit