Description: SM-BGA socket for BGA223 19x15 array 0.5mm pitch 8mm x 10mm x 1.2mm DUT

Size: px
Start display at page:

Download "Description: SM-BGA socket for BGA223 19x15 array 0.5mm pitch 8mm x 10mm x 1.2mm DUT"

Transcription

1 Silver Ball Matrix BG Socket Recommended Torque 1.5 in-lb. Features Wide temperature range (-55C to +150C). Current capability is 4 per pin. Over 40GHz for edge pins. Low and stable contact resistance for reliable production yield. Highly compliant to accommodate wide co-planarity variations. Capacitance under 0.15pF TOP VIEW 8.83 B 1.59 DETIL B SCLE 20 : SECTION - Description: SM-BG socket for BG223 19x15 array 0.5mm pitch 8mm x 10mm x 1.2mm DUT SM-BG-9058 Drawing STTUS: Released FILE: SM-BG-9058 Dwg SHEET: 1 OF 5 DRWN BY: M. Raske DTE: 12/12/2014 REV. SCLE: 3.5:1

2 9.00 *Note: BG pattern is not symmetrical with respect to the mounting holes, it is offset 0.25mm * BG pin 1 orientation 1.70±0.10 (x4) NON-PLTED MOUNTING HOLE 0.85±0.025 (x2) NON-PLTED LIGNMENT HOLE (x4) (x223 pad) (x4) Socket Base Outline Description: Recommended PCB Layout Socket Base Outline Target PCB Recommendations Total thickness: 1.6mm min. Plating: Gold or Solder finish PCB Pad height: same or higher than solder mask SM-BG-9058 Drawing STTUS: Released FILE: SM-BG-9058 Dwg SHEET: 2 OF 5 DRWN BY: M. Raske DTE: 12/12/2014 REV. SCLE: 6:1

3 Y D BG PIN 1 MRKING X ddd C b 0.15 X Y 0.05 e Z 0.08 Z E TOP VIEW 1 BOTTOM VIEW SIDE VIEW Ironwood Package Code: BG Dimensions are in millimeters. 2. Interpret dimensions and tolerances per SME Y14.5M Dimension b is measured at the maximum solder ball diameter, parallel to datum plane Z. 4. Datum Z (seating plane) is defined by the spherical crowns of the solder balls. 5. Parallelism measurement shall exclude any effect of mark on top surface of package. Description: Compatible BG SM-BG-9058 Drawing STTUS: Released FILE: SM-BG-9058 Dwg DIM MIN NOM MX D E b e 0.5 BSC RRY 19x15 PIN COUNT 223 SHEET: 3 OF 5 DRWN BY: M. Raske DTE: 12/12/2014 REV. SCLE: 8:1

4 ITEM NO. Description Material 4 1 SM Socket Base 10mm IC 3mm Thk 0.25mm shift 7075-T6 luminum lloy 2 Socket Lid 7075-T6 luminum lloy 3 Compression Plate for 8.9x9.2mm IC 7075-T6 luminum lloy 2 4 Compression Screw M6x1 Stainless Steel (18-8) 5 #0-80 X.313 LG, SOC HD CP SCREW, LLOY STL, BLK OXIDE lloy Steel 6 #0-80 Shoulder Screw, 0.062" thread length Stainless Steel (303) Test board, daisy chain, for 8x10mm body, 0.5mm, 19x15 array 8 BG test chip, 8x10mm body, 0.5mm, 19x15 array FR Dowel Pin, 1/32" x 3/16", SS Chrome Stainless Steel 10 Ball guide BG223 19x15 array 0.5mm pitch 8mm x 10mm DUT Kapton Polyimide/Cirlex 11 IC Guide BG223 19x15 array 0.5mm pitch 8mm x 10mm 1.2mm thick Torlon SM elastomer; BG223 19x15 array 0.5mm pitch 8mm x 10mm DUT SM elastomer Backing Plate 7075-T6 lumium lloy 14 Insulation Plate FR4 High temp 10 BG pin 1 Socket base pin Description: SM-BG socket for BG223 19x15 array 0.5mm pitch 8mm x 10mm x 1.2mm DUT SM-BG-9058 Drawing STTUS: Released FILE: SM-BG-9058 Dwg 4X THRU LL 0-80 UNF THRU LL Insulation plate - Backing plate stack-up SHEET: 4 OF 5 DRWN BY: M. Raske DTE: 12/12/2014 REV. SCLE: 3.5:1 4.59

5 BG PIN 1 ORIENTTION SM elastomer layout (Top View) Target PCB layout (Top View) SOCKET BSE OUTLINE BCKING PLTE OUTLINE Description: SM-BG socket for BG223 19x15 array 0.5mm pitch 8mm x 10mm x 1.2mm DUT Rev Date Initials Description 12/12/14 MR Original SM-BG-9058 Drawing STTUS: Released FILE: SM-BG-9058 Dwg SHEET: 5 OF 5 DRWN BY: M. Raske DTE: 12/12/2014 REV. SCLE: 6:1

Silver Ball Matrix BGA Socket

Silver Ball Matrix BGA Socket A1 corner 4.600 Silver Ball Matrix BGA Socket Features Wide temperature range (-55C to +0C). Current capability is 4A per pin. Over 40GHz bandwidth @-1dB for edge pins. Low and stable contact resistance

More information

GHz BGA SOCKET - direct mount, solderless

GHz BGA SOCKET - direct mount, solderless 45.00±0.25 GHz BGA SOCKET - direct mount, solderless Features Directly mounts to target PCB (needs tooling holes) with hardware High speed reliable elastomer connection Minimum real estate required Compression

More information

Features. Description: SG-MLF Socket for 8x8mm. Recommended torque = 1.25 lbf-in. (14.1 N-cm) SG-MLF-7007 Drawing

Features. Description: SG-MLF Socket for 8x8mm. Recommended torque = 1.25 lbf-in. (14.1 N-cm) SG-MLF-7007 Drawing GHz MLF Socket - Direct mount, solderless Features Directly mounts to target PCB (needs tooling holes) with hardware High speed reliable elastomer connection Minimum real estate required Compression plate

More information

GHz BGA Socket - Direct mount, solderless

GHz BGA Socket - Direct mount, solderless GHz BGA Socket - Direct mount, solderless Features 10.625 14.500 Directly mounts to target PCB (needs tooling holes) with hardware High speed, reliable Elastomer connection Minimum real estate required

More information

SMP-CGA DIRECT MOUNT, SOLDERLESS SOCKET FOR BURN-IN AND TEST APPLICATIONS

SMP-CGA DIRECT MOUNT, SOLDERLESS SOCKET FOR BURN-IN AND TEST APPLICATIONS 38.500 SMP-CGA DIRECT MOUNT, SOLDERLESS SOCKET FOR BURN-IN AND TEST APPLICATIONS FEATURES: Wide temperature range (-55C to +155C ) xga IC High current capability (up to 4A ) Excellent signal integrity

More information

Interposer MATED HEIGHT

Interposer MATED HEIGHT Product Specification: FEATURES High Performance PCBeam Connector Technology Product options at 1.27mm, 1.0mm, and 0.8mm pitch Maximized pin count per form factor 3 form factor sizes available Standard

More information

Product Specification - LPM Connector Family

Product Specification - LPM Connector Family LPM Product Specification - LPM OVERVIEW Developed for mobile devices and other space-constrained applications, the Neoconix LPM line of connectors feature exceptional X-Y-Z density with a simple, highly

More information

CLICK HERE TO GO BACK TO PART NUMBER OVERVIEW. QFP/TQFP - 64 Pins (10x10) 0.5mm pitch. Detail C. Detail B

CLICK HERE TO GO BACK TO PART NUMBER OVERVIEW. QFP/TQFP - 64 Pins (10x10) 0.5mm pitch. Detail C. Detail B QFP/TQFP - 64 Pins (10x10) 0.5mm pitch Withstanding Voltage: 100V eff Solvent Durability: Freon Part Number (Details) IC149-064 - *69 - B5 B5 = Au over Ni Not available Detail C 10mm x 10mm N1 Detail B

More information

Features. = +25 C, Vdd = 5V, Vgg1 = Vgg2 = Open

Features. = +25 C, Vdd = 5V, Vgg1 = Vgg2 = Open v3.117 HMC441LM1 Typical Applications The HMC441LM1 is a medium PA for: Point-to-Point Radios Point-to-Multi-Point Radios VSAT LO Driver for HMC Mixers Military EW & ECM Functional Diagram Vgg1, Vgg2:

More information

TN016. PCB Design Guidelines for 5x5 DFN Sensors. Introduction. Package Marking

TN016. PCB Design Guidelines for 5x5 DFN Sensors. Introduction. Package Marking PCB Design Guidelines for 5x5 DFN Sensors Introduction This technical note is intended to provide information about Kionix s 5 x 5 mm DFN (non wettable flank, i.e. standard) packages and guidelines for

More information

Data Sheet. ACFF-1024 ISM Bandpass Filter ( MHz) Description. Features. Specifications. Functional Block Diagram.

Data Sheet. ACFF-1024 ISM Bandpass Filter ( MHz) Description. Features. Specifications. Functional Block Diagram. ACFF-124 ISM Bandpass Filter (241 2482 MHz) Data Sheet Description The Avago ACFF-124 is a miniaturized Bandpass Filter designed for use in the 2.4 GHz Industrial, Scientific and Medical (ISM) band. The

More information

Electrical Specifications. Insertion to +85 TOP VIEW SIDE VIEW BOTTOM VIEW. Pin 2. Yantel Corporation

Electrical Specifications. Insertion to +85 TOP VIEW SIDE VIEW BOTTOM VIEW. Pin 2. Yantel Corporation Description The is a low profile, high performance 20dB directional coupler. It is designed for DCS & PCS applications. This component is suitable for feed-forward amplifier and signal sampling circuits

More information

CALL (512 ) x6400

CALL (512 ) x6400 The AirBorn stackable compliant connector family is one of AirBorn s solutions for high-density, board-to-board stacking applications. This connector family is available in 0.075 contact spacing and 100

More information

Product Specification - LPS Connector Series

Product Specification - LPS Connector Series LPS Product Specification - LPS OVERVIEW The LPS products are solderable versions of those in the Neoconix LPM product series. Also developed for mobile devices and other space-constrained applications,

More information

GaAS MMIC SMT LOW DISTORTION T/R SWITCH DC GHZ

GaAS MMIC SMT LOW DISTORTION T/R SWITCH DC GHZ '99 MICROWVE CORPORTI GaS MMIC LOW DISTORTI T/R SWITCH DC - 2.5 GHZ Features General Description HIGH THIRD ORDER INTERCEPT: + m SINGLE POSITIVE SUPPLY: +3 TO +V HIGH POWER CPILITY TTL/CMOS CTROL The is

More information

From dc to 10 GHz the. VSWR shall not exceed 1.3 &.04 (f) where f is the frequency in Gigahertz (GHz).

From dc to 10 GHz the. VSWR shall not exceed 1.3 &.04 (f) where f is the frequency in Gigahertz (GHz). 121 Series Coaxial Snap On & Screw On Types / 50 Ohm & 75 Ohm These 50 and 75 Ohm coaxial connectors are easily inserted into your printed circuit board using an insertion tool. Solder is eliminated and

More information

Matrix BGA Socket Assembly Instructions

Matrix BGA Socket Assembly Instructions s 0,80mm, 1,00mm, 1,7mm Pitch MPI-1758-01 Rev. 1 4 5 6 7 1. mm Hex Wrench (Not Supplied.). Spring Plate Assembly. ( Item). Top Support Plate. ( Item) 4. BGA Package (Not Supplied.) 5. Matrix MPI BGA Socket

More information

High Isolation SP4T SWITCH

High Isolation SP4T SWITCH High Isolation SP4T SWITCH NJG1699MD7 GENERAL DESCRIPTION The NJG1699MD7 is a GaAs high isolation SP4T switch MMIC. It features low insertion loss and very high isolation. It has integrated DC blocking

More information

TN008. PCB Design Guidelines for 2x2 LGA Sensors. Introduction. 2x2 LGA Package Marking

TN008. PCB Design Guidelines for 2x2 LGA Sensors. Introduction. 2x2 LGA Package Marking PCB Design Guidelines for 2x2 LGA Sensors Introduction This technical note is intended to provide information about Kionix s 2 x 2 mm LGA packages and guidelines for developing PCB land pattern layouts.

More information

Low-Cost PCB Design 1

Low-Cost PCB Design 1 Low-Cost PCB Design 1 PCB design parameters Defining PCB design parameters begins with understanding: End product features, uses, environment, and lifetime goals PCB performance, manufacturing, and yield

More information

Top View (Near-side) Side View Bottom View (Far-side) .89±.08. 4x.280. Orientation Marker Orientation Marker.

Top View (Near-side) Side View Bottom View (Far-side) .89±.08. 4x.280. Orientation Marker Orientation Marker. Model B2F2AHF Ultra Low Profile 168 Balun Ω to 2Ω Balanced Description The B2F2AHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential input locations on data conversion

More information

MAXIMUM RATINGS Note Parameter Conditions/comments Value Unit

MAXIMUM RATINGS Note Parameter Conditions/comments Value Unit The CT2 Audio Volume Controls are high quality stepped 24-position attenuators. Designed for maximum sonic quality, accuracy and reliability. This makes them equally suited for audiophile and professional

More information

Features. = +25 C, Vdd = +3V

Features. = +25 C, Vdd = +3V v.117 HMC3LPE Typical Applications Features The HMC3LPE is ideal for: Millimeterwave Point-to-Point Radios LMDS VSAT SATCOM Functional Diagram Low Noise Figure:. db High Gain: db Single Positive Supply:

More information

DATASHEET HA-2520, HA-2522, HA Features. Applications. Ordering Information

DATASHEET HA-2520, HA-2522, HA Features. Applications. Ordering Information DATASHEET 2MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers FN2894 Rev 1. comprise a series of operational amplifiers delivering an unsurpassed combination of specifications

More information

Data Sheet. ACMD-6103 Band 3 Duplexer. Description. Features. Specifications. Applications. Functional Block Diagram

Data Sheet. ACMD-6103 Band 3 Duplexer. Description. Features. Specifications. Applications. Functional Block Diagram ACMD-613 Band 3 Duplexer Data Sheet Description The Avago Technologies ACMD-613 is a highly miniaturized duplexer designed for use in LTE Band 3 (171 1785 MHz UL, 185 188 MHz DL) handsets and mobile data

More information

Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED

Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK Typical Applications The is ideal

More information

Features. Parameter Frequency Min. Typ. Max. Units. Return Loss Off State DC - 20 GHz 19 db

Features. Parameter Frequency Min. Typ. Max. Units. Return Loss Off State DC - 20 GHz 19 db Typical Applications The is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military & Space Hybrids Test Instrumentation SATCOM & Sensors Functional Diagram Features Broadband Performance: DC

More information

Made in USA. Download a full set of drawings from MorrisonandMarvin.com. Vise Assembly MORRISON & MARVIN ENGINE WORKS

Made in USA. Download a full set of drawings from MorrisonandMarvin.com. Vise Assembly MORRISON & MARVIN ENGINE WORKS Download a full set of drawings from MorrisonandMarvin.com Made in US DESIGNED Y DRWN Y ox 555 enton City, W 99320 US 4:1 Vise ssembly 1 of 18 1 14 3 6 7 18 5 2 11 12 9 10 13 1 15 16 17 Download a full

More information

2x2 mm LGA Package Guidelines for Printed Circuit Board Design. Figure 1. 2x2 mm LGA package marking information.

2x2 mm LGA Package Guidelines for Printed Circuit Board Design. Figure 1. 2x2 mm LGA package marking information. 2x2 mm LGA Package Guidelines for Printed Circuit Board Design This technical note is intended to provide information about Kionix s 2 x 2 mm LGA packages and guidelines for developing PCB land pattern

More information

Model PD0409J7575S2HF

Model PD0409J7575S2HF Model PD49J77SHF Ultra Low Profile 8 Power Divider 7Ω to 7Ω Description The PD49J77SHF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD49J77SHF is

More information

Data Sheet. ACMD-6003 UMTS Band 3 Duplexer. Features. Description. Specifications. Applications. Functional Block Diagram

Data Sheet. ACMD-6003 UMTS Band 3 Duplexer. Features. Description. Specifications. Applications. Functional Block Diagram ACMD-63 UMTS Band 3 Duplexer Data Sheet Description The Avago ACMD-63 is a highly miniaturized duplexer designed for use in UMTS Band 3 (171 1785 MHz UL, 185 188 MHz DL) handsets and mobile data terminals.

More information

ENGINEERING STANDARDS SECTION: D TOG-L-LOC V-LOC OVAL-LOC LANCE-N-LOC INFORMATION. Tog-L-Loc. How The Joining Process Works

ENGINEERING STANDARDS SECTION: D TOG-L-LOC V-LOC OVAL-LOC LANCE-N-LOC INFORMATION. Tog-L-Loc. How The Joining Process Works Tog-L-Loc Tog-L-Loc is a circular, leakproof joint formed by drawing the metals into a circular "cup'' and then expanding the diameter to form a 360 radial lock below the bottom sheet. How The Joining

More information

Model PD3150J5050S2HF

Model PD3150J5050S2HF Model PD315J55S2HF Ultra Low Profile 85 Power Divider 5Ω to 5Ω Description The PD315J55S2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD315J55S2HF

More information

Model PD0409J5050S2HF

Model PD0409J5050S2HF Model PD49JSHF Ultra Low Profile 8 Power Divider Ω to Ω Description The PD49JSHF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD49JSHF is ideal for

More information

Power MOSFET T C = 25 C. V GS at 10 V

Power MOSFET T C = 25 C. V GS at 10 V IRFF20S, SiHFF20S, IRFF20L, SiHFF20L Power MOSFET PRODUCT SUMMRY V DS (V) 900 R DS(on) ( ) V GS = 10 V 8.0 Q g (Max.) (nc) 38 Q gs (nc) 4.7 Q gd (nc) 21 Configuration Single I 2 PK (TO-262) D 2 PK (TO-263)

More information

Model PD2328J5050S2HF

Model PD2328J5050S2HF Model PD2328J55S2HF Ultra Low Profile 85 Power Divider 5Ω to 5Ω Description The PD2328J55S2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD2328J55S2HF

More information

Surface Mount SOT-363 (SC-70) Package. Pin Connections and Package Marking GND 1 4 V CC

Surface Mount SOT-363 (SC-70) Package. Pin Connections and Package Marking GND 1 4 V CC GHz Low Noise Silicon MMIC Amplifier Technical Data INA-63 Features Ultra-Miniature Package Internally Biased, Single 5 V Supply (12 ma) db Gain 3 db NF Unconditionally Stable Applications Amplifier for

More information

HA Features. Quad, 3.5MHz, Operational Amplifier. Applications. Pinout. Ordering Information. Data Sheet July 2004 FN2922.5

HA Features. Quad, 3.5MHz, Operational Amplifier. Applications. Pinout. Ordering Information. Data Sheet July 2004 FN2922.5 HA-4741 Data Sheet July 24 FN2922. Quad, 3.MHz, Operational Amplifier HA-4741, which contains four amplifiers on a monolithic chip, provides a new measure of performance for general purpose operational

More information

TEL: FAX: Electrical Specifications, (continued) Parameter Conditions Min. Typ. Max Units Output Low Voltage 2 V Output Rise /

TEL: FAX: Electrical Specifications, (continued) Parameter Conditions Min. Typ. Max Units Output Low Voltage 2 V Output Rise / TEL:055-83396822 FAX:055-8336182 Typical Applications Features The is ideal for: RF ATE Applications Broadband Test & Measurement Serial Data Transmission up to 13 Gbps Digital Logic Systems up to 13 GHz

More information

Top View (Near-side) Side View Bottom View (Far-side) ± ±.08. 4x.28. Orientation Marker Balanced port 1.

Top View (Near-side) Side View Bottom View (Far-side) ± ±.08. 4x.28. Orientation Marker Balanced port 1. Model BD2FAHF Ultra Low Profile 168 Balun Ω to Ω Balanced Description The BD2FAHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential input locations on data conversion

More information

OBSOLETE HMC915LP4E. GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, GHz. Typical Applications. Features. Functional Diagram. General Description

OBSOLETE HMC915LP4E. GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, GHz. Typical Applications. Features. Functional Diagram. General Description v1.5 LO AMPLIFIER,.5-2.7 GHz Typical Applications The is ideal for: PCS / 3G Infrastructure Base Stations & Repeaters WiMAX & WiBro ISM & Fixed Wireless Functional Diagram Features Input IP3: +28 dbm Low

More information

HA-2640, HA Features. 4MHz, High Supply Voltage Operational Amplifiers. Applications. Ordering Information. Pinouts

HA-2640, HA Features. 4MHz, High Supply Voltage Operational Amplifiers. Applications. Ordering Information. Pinouts HA-264, HA-2645 Data Sheet January 3, 26 FN294.5 4MHz, High Supply Voltage Operational Amplifiers HA-264 and HA-2645 are monolithic operational amplifiers which are designed to deliver unprecedented dynamic

More information

Surface Mount SOT-363 (SC-70) Package. Pin Connections and Package Marking 4 V CC. Note: Package marking provides orientation and identification.

Surface Mount SOT-363 (SC-70) Package. Pin Connections and Package Marking 4 V CC. Note: Package marking provides orientation and identification. 1.5 GHz Low Noise Silicon MMIC Amplifier Technical Data INA-52063 Features Ultra-Miniature Package Single 5 V Supply (30 ma) 22 db Gain 8 dbm P 1dB Unconditionally Stable Applications Amplifier for Cellular,

More information

SBB-3089Z Pb MHz InGaP HBT Active Bias Gain Block

SBB-3089Z Pb MHz InGaP HBT Active Bias Gain Block Product Description Sirenza Microdevices SBB-389Z is a high performance InGaP HBT MMIC amplifier utilizing a Darlington configuration with an active bias network. The active bias network provides stable

More information

DATASHEET HA Features. Applications. Pinout. Ordering Information. Quad, 3.5MHz, Operational Amplifier. FN2922 Rev 5.00 Page 1 of 8.

DATASHEET HA Features. Applications. Pinout. Ordering Information. Quad, 3.5MHz, Operational Amplifier. FN2922 Rev 5.00 Page 1 of 8. DATASHEET HA-4741 Quad, 3.5MHz, Operational Amplifier HA-4741, which contains four amplifiers on a monolithic chip, provides a new measure of performance for general purpose operational amplifiers. Each

More information

Product Description. Ordering Information. GaAs HBT GaAs MESFET InGaP HBT

Product Description. Ordering Information. GaAs HBT GaAs MESFET InGaP HBT Basestation pplications Broadband, Low-Noise Gain Blocks IF or RF Buffer mplifiers Driver Stage for Power mplifiers Final P for Low-Power pplications High Reliability pplications RF3396General Purpose

More information

20 MHz to 6 GHz RF/IF Gain Block ADL5542

20 MHz to 6 GHz RF/IF Gain Block ADL5542 FEATURES Fixed gain of db Operation up to 6 GHz Input/output internally matched to Ω Integrated bias control circuit Output IP3 46 dbm at MHz 4 dbm at 9 MHz Output 1 db compression:.6 db at 9 MHz Noise

More information

Part No. Output Voltage Tolerance Package Marking HT V 3% HT V 3% HT V 3% HT V 3% HT

Part No. Output Voltage Tolerance Package Marking HT V 3% HT V 3% HT V 3% HT V 3% HT 100mA Voltage Regulator Features Low power consumption Low voltage drop Low temperature coefficient High input voltage (up to 24V) High output current : 100mA (P d 250mW) Output voltage accuracy: tolerance

More information

Spring Loaded Contacts

Spring Loaded Contacts Spring Loaded Contacts Contents ATE Spring Probes Specifications One Part Probes Two Part Probes Spring Loaded Contacts Specifications Spring Loaded Contact Connectors Single Spring Loaded Contacts SMT

More information

EIA Standard Board Layout Drawing for BGA, CCGA, CSP, and QFN

EIA Standard Board Layout Drawing for BGA, CCGA, CSP, and QFN EIA Standard Board Layout Drawing for BGA, CCGA, CSP, and QFN March 2008 DL SM SL VL TH LW A_A A_A Figure 1: Suggested Board Layout of Soldered Pads for BGA Packages Notes: 1. Table 2a through Table 6

More information

TGV2561-SM GHz VCO with Divide by 2

TGV2561-SM GHz VCO with Divide by 2 GND RFout / 2 Vtune TGV2561-SM Applications Point to Point Radio / VSAT Millimeter-wave Communications Test Equipment 32-pin 5x5mm package Product Features Functional Block Diagram Frequency range: 8.9

More information

IIHS LATCH Measurement Tool Set Drawings REV1. iihs.org

IIHS LATCH Measurement Tool Set Drawings REV1. iihs.org IIHS LTCH Measurement Tool Set Drawings REV1 iihs.org REV. DESCRIPTION DTE BY DD STORGE CSE. CHNGE IIHS LOGO. 2/1/2017 RGJ LTCH FORCE TOOL WITH DEPTH SHIELD SHEET 3-4, 9 WGNER INSTRUMENTS FDX100 WWW.WGNERINSTRUMEMTS.COM

More information

Features. Upconversion & Downconversion Applications MIXERS - SINGLE & DOUBLE BALANCED - SMT

Features. Upconversion & Downconversion Applications MIXERS - SINGLE & DOUBLE BALANCED - SMT v1. Typical Applications The HMC688LP4(E) is Ideal for: Cellular/3G & LTE/WiMAX/4G Basestations & Repeaters GSM, CDMA & OFDM Transmitters and Receivers Features High Input IP3: +35 dbm Low Conversion Loss:

More information

Data Sheet. ACMD-6125 Band 25 Duplexer. Description. Features. Specifications, 10 C to +85 C. Applications. Functional Block Diagram

Data Sheet. ACMD-6125 Band 25 Duplexer. Description. Features. Specifications, 10 C to +85 C. Applications. Functional Block Diagram ACMD-6125 Band 25 Duplexer Data Sheet Description The Avago ACMD-6125 is a highly miniaturized duplexer designed for use in Band 25 (185.25 1914.75 MHz UL, 193.25 1994.75 MHz DL) handsets and mobile data

More information

Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED

Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK v1.14 AMPLIFIER, 18-4 GHz Typical

More information

HMC6380LC4B. WIDEBAND VCOs - SMT. Electrical Specifications, T A. Typical Applications. Features. General Description. Functional Diagram

HMC6380LC4B. WIDEBAND VCOs - SMT. Electrical Specifications, T A. Typical Applications. Features. General Description. Functional Diagram Typical Applications Low Noise wideband MMIC VCO is ideal for: Industrial/Medical Equipment Test & Measurement Equipment Satcom Military Radar, EW, & ECM Functional Diagram Features Wide Tuning Bandwidth

More information

DATASHEET ISL9021A. Features. Pinouts. Applications. 250mA Single LDO with Low I Q, Low Noise and High PSRR LDO. FN6867 Rev 2.

DATASHEET ISL9021A. Features. Pinouts. Applications. 250mA Single LDO with Low I Q, Low Noise and High PSRR LDO. FN6867 Rev 2. NOT RECOMMENDED FOR NEW DESIGNS RECOMMENDED REPLACEMENT PART ISL9021A 250mA Single LDO with Low I Q, Low Noise and High PSRR LDO DATASHEET FN6867 Rev 2.00 The ISL9021 is a single LDO providing high performance

More information

Features. Upconversion & Downconversion Applications MIXERS - SINGLE & DOUBLE BALANCED - SMT

Features. Upconversion & Downconversion Applications MIXERS - SINGLE & DOUBLE BALANCED - SMT v1. Typical Applications The HMC689LP4(E) is Ideal for: Cellular/3G & LTE/WiMAX/4G Basestations & Repeaters GSM, CDMA & OFDM Transmitters and Receivers Features High Input IP3: +32 dbm Low Conversion Loss:

More information

Features. Preliminary. = +25 C, IF = 1 GHz, LO = +13 dbm*

Features. Preliminary. = +25 C, IF = 1 GHz, LO = +13 dbm* Typical Applications Features The is ideal for: Test Equipment & Sensors Point-to-Point Radios Point-to-Multi-Point Radios Military & Space Functional Diagram Wide IF Bandwidth: DC - 17 GHz Input IP3:

More information

Data Sheet. ACMD-6103 Band 3 Duplexer. Description. Features. Specifications. Applications. Functional Block Diagram

Data Sheet. ACMD-6103 Band 3 Duplexer. Description. Features. Specifications. Applications. Functional Block Diagram ACMD-613 Band 3 Duplexer Data Sheet Description The Avago Technologies ACMD-613 is a highly miniaturized duplexer designed for use in LTE Band 3 (171 1785 MHz UL, 185 188 MHz DL) handsets and mobile data

More information

SLVDA2.8LC. 600 WATT MULTI-LINE ultra LOW CAPACITANCE TVS ARRAY PIN CONFIGURATION

SLVDA2.8LC. 600 WATT MULTI-LINE ultra LOW CAPACITANCE TVS ARRAY PIN CONFIGURATION 600 WATT MULTI-LINE ultra LOW CAPACITANCE TVS ARRAY Description The is an ultra low capacitance TVS array that provides four line pairs of protection. This device protects high-frequency applications such

More information

TQP3M9018 High Linearity LNA Gain Block

TQP3M9018 High Linearity LNA Gain Block Applications Repeaters Mobile Infrastructure LTE / WCDMA / CDMA / EDGE General Purpose Wireless 6 Pin x mm QFN Package Product Features Functional Block Diagram -4 MHz.5 db Gain at 9 MHz. db Noise Figure

More information

TEL: FAX: Electrical Specifications, (continued) Parameter Conditions Min. Typ. Max Units Output Rise / Fall Time Differential,

TEL: FAX: Electrical Specifications, (continued) Parameter Conditions Min. Typ. Max Units Output Rise / Fall Time Differential, TEL:055-83396822 FAX:055-8336182 Typical Applications Features The is ideal for: Serial Data Transmission up to 26 Gbps High Speed Frequency Divider (up to 26 GHz) Broadband Test & Measurement RF ATE Applications

More information

Return loss (db) Insertion loss (db) .56±.06 TBD. GND / DC Feed 1 + RF GND 2. Unbalanced Port Balanced Port Balanced Port.

Return loss (db) Insertion loss (db) .56±.06 TBD. GND / DC Feed 1 + RF GND 2. Unbalanced Port Balanced Port Balanced Port. Model BD6N5AHF Ultra Low Profile 44 Balun 5Ω to Ω Balanced Description The BD6N5AHF is a low cost, low profile sub-miniature unbalanced to balanced transformer designed for differential inputs and output

More information

TQP7M W High Linearity Amplifier. Applications. Ordering Information

TQP7M W High Linearity Amplifier. Applications. Ordering Information Applications Repeaters BTS Transceivers BTS High Power Amplifiers CDMA / WCDMA / LTE General Purpose Wireless 3-pin SOT-89 Package Product Features 5-15 MHz +3 dbm P1dB at 94MHz +49 dbm Output IP3 at 94MHz

More information

SBB-5089Z GHz, Cascadable Active Bias InGaP HBT MMIC Amplifier

SBB-5089Z GHz, Cascadable Active Bias InGaP HBT MMIC Amplifier Product Description Sirenza Microdevices SBB-89Z is a high performance InGaP HBT MMIC amplifier utilizing a Darlington configuration with an active bias network. The active bias network provides stable

More information

Features. = +25 C, IF = 200 MHz, LO = 0 dbm, Vcc = Vcc1, 2, 3 = +5V, G_Bias = +2.5V*

Features. = +25 C, IF = 200 MHz, LO = 0 dbm, Vcc = Vcc1, 2, 3 = +5V, G_Bias = +2.5V* v4.1 Typical Applications The HMC685LP4(E) is Ideal for: Cellular/3G & LTE/WiMAX/4G Basestations & Repeaters GSM, CDMA & OFDM Transmitters and Receivers Features High Input IP3: +35 dbm 8 db Conversion

More information

Features TEMP. RANGE ( C)

Features TEMP. RANGE ( C) DATASHEET HFA0, HFA09, HFA27, HFA28 Ultra High Frequency Transistor Arrays The HFA0, HFA09, HFA27 and the HFA28 are Ultra High Frequency Transistor Arrays that are fabricated from Intersil Corporation

More information

Features. = +25 C, Vcc = +5V [1]

Features. = +25 C, Vcc = +5V [1] Typical Applications Low Noise wideband MMIC VCO is ideal for: Features Wide Tuning Bandwidth Industrial/Medical Equipment Test & Measurement Equipment Military Radar, EW & ECM Functional Diagram Pout:

More information

Model B0922N7575AHF Rev B. Ultra Low Profile 0404 Balun

Model B0922N7575AHF Rev B. Ultra Low Profile 0404 Balun Model B9N7575AHF Ultra Low Profile 44 Balun 75Ω to 75Ω Balanced Description The B9N7575AHF is a low profile, low impedance mm square subminiature wideband unbalanced to balanced transformer designed for

More information

B2501 B Series 0.5mm (.0197) Pitch

B2501 B Series 0.5mm (.0197) Pitch B Series 0.5mm (.0197) Pitch FEATURES

More information

TQP3M9008 High Linearity LNA Gain Block

TQP3M9008 High Linearity LNA Gain Block General Description The is a cascadable, high linearity gain block amplifier in a low-cost surface-mount package. At 1.9 GHz, the amplifier typically provides 2.6 db gain, +36 dbm OIP3, and 1.3 db Noise

More information

HMC540SLP3E v db LSB SILICON MMIC 4-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, GHz

HMC540SLP3E v db LSB SILICON MMIC 4-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, GHz HMC54SLP3E v.95 LSB SILICON MMIC 4-BIT DIGITAL POSITIVE CONTROL ATTENUATOR,. - 8 GHz Typical Applications Features The HMC54SLP3E is ideal for both RF and IF applications: Cellular Infrastructure Wireless

More information

Features. mvp-p Differential, peak-to-peak Input High Voltage V Input Low Voltage -1 0 V. Differential, 40 Gbps

Features. mvp-p Differential, peak-to-peak Input High Voltage V Input Low Voltage -1 0 V. Differential, 40 Gbps Typical Applications Features The is ideal for: RF ATE Applications Broadband Test & Measurement Serial Data Transmission up to 45 Gbps Digital Logic Systems up to 25 GHz NRZ-to-RZ Conversion Functional

More information

SBB-1089 SBB-1089Z MHz, Cascadable Active Bias InGaP/GaAs HBT MMIC Amplifier

SBB-1089 SBB-1089Z MHz, Cascadable Active Bias InGaP/GaAs HBT MMIC Amplifier Product Description Sirenza Microdevices SBB89 is a high performance InGaP HBT MMIC amplifier utilizing a Darlington configuration with an active bias network. The active bias network provides stable current

More information

Power MOSFET. 50 I D T C = 100 C 50 Pulsed Drain Current a, e I DM 290 Linear Derating Factor 1.3 W/ C Single Pulse Avalanche Energy b, e E AS 100 mj

Power MOSFET. 50 I D T C = 100 C 50 Pulsed Drain Current a, e I DM 290 Linear Derating Factor 1.3 W/ C Single Pulse Avalanche Energy b, e E AS 100 mj Power MOSFET PRODUCT SUMMRY V DS (V) 60 R DS(on) () V GS = 10 V 0.018 Q g (Max.) (nc) 110 Q gs (nc) 29 Q gd (nc) 36 Configuration Single D I 2 PK (TO-262) D 2 PK (TO-263) FETURES dvanced process technology

More information

HMC997LC4. Variable Gain Amplifier - SMT. VARIABLE GAIN AMPLIFIER GHz. Typical Applications. General Description. Functional Diagram

HMC997LC4. Variable Gain Amplifier - SMT. VARIABLE GAIN AMPLIFIER GHz. Typical Applications. General Description. Functional Diagram v2.14 Typical Applications The is ideal for: Point-to-Point Radio Point-to-Multi-Point Radio EW & ECM Subsystems Ka-Band Radar Test Equipment Functional Diagram Features Wide Gain Control Range: 1 db Single

More information

Parameter Frequency Min. Typ. Max. Units GHz GHz Attenuation Range GHz 31.5 db

Parameter Frequency Min. Typ. Max. Units GHz GHz Attenuation Range GHz 31.5 db v.37. db LSB GaAs MMIC 6-BIT DIGITAL POSITIVE CONTROL ATTENUATOR,. - 8. GHz Typical Applications Features ATTENUATORS - SMT The HMCALP3E is ideal for: WLAN & Point-to-Multi-Point Fiber Optics & Broadband

More information

GaAs, phemt, MMIC, Single Positive Supply, DC to 7.5 GHz, 1 W Power Amplifier HMC637BPM5E

GaAs, phemt, MMIC, Single Positive Supply, DC to 7.5 GHz, 1 W Power Amplifier HMC637BPM5E 9 11 13 31 NIC 3 ACG1 29 ACG2 2 NIC 27 NIC 26 NIC GaAs, phemt, MMIC, Single Positive Supply, DC to 7.5 GHz, 1 W Power Amplifier FEATURES P1dB output power: 2 dbm typical Gain:.5 db typical Output IP3:

More information

Features. = +25 C, IF= 100 MHz, LO= +15 dbm* Parameter Min. Typ. Max. Min. Typ. Max. Units

Features. = +25 C, IF= 100 MHz, LO= +15 dbm* Parameter Min. Typ. Max. Min. Typ. Max. Units v2.514 MIXER, 2.5-7. GHz Typical Applications The is ideal for: WiMAX & Fixed Wireless Point-to-Point Radios Point-to-Multi-Point Radios Test Equipment & Sensors Military End-Use Functional Diagram Features

More information

Features = +5V. = +25 C, Vdd 1. = Vdd 2

Features = +5V. = +25 C, Vdd 1. = Vdd 2 v1.11 HMC51LP3 / 51LP3E POWER AMPLIFIER, 5-1 GHz Typical Applications The HMC51LP3(E) is ideal for: Microwave Radio & VSAT Military & Space Test Equipment & Sensors Fiber Optics LO Driver for HMC Mixers

More information

NORTH AMERICA ONLY PIPE SLUG CHUTE DETAILS ALL DIMENSIONS IN INCHES

NORTH AMERICA ONLY PIPE SLUG CHUTE DETAILS ALL DIMENSIONS IN INCHES "B" B. C. PIPE SLUG CHUTE DETAILS ALL DIMENSIONS IN INCHES PVC - DWV PIPE FITTINGS FOR "X" SOC. HD. SCREW (N) HOLES "D" "C" "A" O.D. ALTER IF CONSTRAINED BY SPACE LIMITATION. (2) MIN. FASTENING HOLES REQUIRED.

More information

SLVU WATT MULTI-LINE ULTRA LOW CAPACITANCE TVS ARRAY DESCRIPTION SO-8 PACKAGE APPLICATIONS FEATURES MECHANICAL CHARACTERISTICS

SLVU WATT MULTI-LINE ULTRA LOW CAPACITANCE TVS ARRAY DESCRIPTION SO-8 PACKAGE APPLICATIONS FEATURES MECHANICAL CHARACTERISTICS 600 WATT MULTI-LINE ULTRA LOW CAPACITANCE TVS ARRAY DESCRIPTION The is an ultra low capacitance TVS array that provides four line pairs of protection. This device protects high-frequency applications such

More information

Data Sheet. ACMD-7409 Miniature PCS Band Duplexer. Features. Description. Specifications. Applications. Functional Block Diagram

Data Sheet. ACMD-7409 Miniature PCS Band Duplexer. Features. Description. Specifications. Applications. Functional Block Diagram ACMD-749 Miniature PCS Band Duplexer Data Sheet Description The Avago ACMD-749 is a miniature duplexer designed for US PCS handsets. The ACMD-749 is designed with Avago Technologies Film Bulk Acoustic

More information

Data Sheet. ACMD-7605 Miniature UMTS Band 8 Duplexer. Description. Features. Specifications

Data Sheet. ACMD-7605 Miniature UMTS Band 8 Duplexer. Description. Features. Specifications ACMD-765 Miniature UMTS Band 8 Duplexer Data Sheet Description The Avago Technologies ACMD-765 is a miniature duplexer designed for use in UMTS Band 8 (88 915 MHz UL, 925 96 MHz DL) handsets and mobile

More information

Features. = +25 C, VDD = +5 V, 0 dbm Drive Level [1]

Features. = +25 C, VDD = +5 V, 0 dbm Drive Level [1] Typical Applications Features The HMC196LP3E is suitable for: Point-to-Point & VSAT Radios Test Instrumentation Military & Space Functional Diagram High Output Power: 12 dbm Low Input Power Drive: -2 to

More information

DATASHEET HA Features. Applications. Ordering Information. Pinouts. 250MHz Video Buffer. FN2924 Rev 8.00 Page 1 of 12.

DATASHEET HA Features. Applications. Ordering Information. Pinouts. 250MHz Video Buffer. FN2924 Rev 8.00 Page 1 of 12. 25MHz Video Buffer NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at -888-INTERSIL or www.intersil.com/tsc DATASHEET FN2924 Rev 8. The HA-533 is a unity

More information

Features. = +25 C, 50 Ohm system

Features. = +25 C, 50 Ohm system v6.312 Typical Applications Features The E is ideal for: Point-to-Point Radio VSAT Radio Test Instrumentation Microwave Sensors Military, ECM & Radar Functional Diagram Wide Bandwidth: 5-26.5 GHz Excellent

More information

HMC1095LP4E v db LSB GaAs MMIC 6-BIT 75 Ohms DIGITAL ATTENUATOR, DC - 3 GHz. Typical Applications. Functional Diagram. General Description

HMC1095LP4E v db LSB GaAs MMIC 6-BIT 75 Ohms DIGITAL ATTENUATOR, DC - 3 GHz. Typical Applications. Functional Diagram. General Description v1.713 Typical Applications The is ideal for: CATV/ Sattelite Set Top Boxes CATV Modems CATV Infrastructure Data Network Equipment Functional Diagram Features.5 db LSB Steps to Power-Up State Selection

More information

Anaren 0805 (B0809J50ATI) balun optimized for Texas Instruments CC1100/CC1101 Transceiver

Anaren 0805 (B0809J50ATI) balun optimized for Texas Instruments CC1100/CC1101 Transceiver (ANN-2005) Rev B Page 1 of 13 Anaren 0805 (B0809J50ATI) balun optimized for Texas Instruments CC1100/CC1101 Transceiver Trong N Duong RF Co-Op Nithya R Subramanian RF Engineer Introduction The tradeoff

More information

SPDT SWITCH GaAs MMIC

SPDT SWITCH GaAs MMIC NJG181K75 SPDT SWITCH GaAs MMIC GENERAL DESCRIPTION The NJG181K75 is a SPDT switch IC suited for switching transmit/receive signals at 82.11 a/b/g/n/ac applications. The NJG181K75 features low insertion

More information

High Isolation, Silicon SPDT, Nonreflective Switch, 0.1 GHz to 6.0 GHz HMC8038W

High Isolation, Silicon SPDT, Nonreflective Switch, 0.1 GHz to 6.0 GHz HMC8038W 5 6 7 8 6 5 4 3 FEATURES Nonreflective, 50 Ω design High isolation: 60 db typical Low insertion loss: 0.8 db typical High power handling 34 dbm through path 29 dbm terminated path High linearity P0.dB:

More information

v3.99 Attenuation vs. Frequency over Vctrl V -1.6 V -.6 V. V Attenuation vs. Vctrl1 Over 1 GHz, Vctrl2

v3.99 Attenuation vs. Frequency over Vctrl V -1.6 V -.6 V. V Attenuation vs. Vctrl1 Over 1 GHz, Vctrl2 5 TEL:755-83396822 FAX:755-83376182 E-MAIL: szss2@163.com Typical Applications v3.99 Features The is ideal for: Point-to-Point Radio VSAT Radio Test Instrumentation Microwave Sensors Military, ECM & Radar

More information

HMC729LC3C HIGH SPEED LOGIC - SMT. 26 GHz, T-FLIP-FLOP w/ RESET. Typical Applications. Features. Functional Diagram. General Description

HMC729LC3C HIGH SPEED LOGIC - SMT. 26 GHz, T-FLIP-FLOP w/ RESET. Typical Applications. Features. Functional Diagram. General Description Typical Applications The is ideal for: Serial Data Transmission up to 26 Gbps High Speed Frequency Divider (up to 26 GHz) Broadband Test & Measurement RF ATE Applications Functional Diagram Features Supports

More information

sealed mini usb connectors

sealed mini usb connectors QUICK CONNECT CABLE END MATES WITH PANEL MOUNT PANEL MOUNT MATES WITH CABLE END REAR VIEW - PC TAIL REAR VIEW - FEED-THRU TERMINATION REAR VIEW - SOLDER HOLES SPECIFICATIONS Mechanical Specifications Life:

More information

Model C1517J5003AHF. Ultra Low Profile db, 90 Hybrid Coupler

Model C1517J5003AHF. Ultra Low Profile db, 90 Hybrid Coupler Model C57J53AHF Ultra Low Profile 85 3 db, 9 Hybrid Coupler Description The C57J53AHF is a low cost, low profile sub-miniature high performance 3 db coupler in an easy to use surface mount package. The

More information

HMC659LC5 LINEAR & POWER AMPLIFIERS - SMT. GaAs PHEMT MMIC POWER AMPLIFIER, DC - 15 GHz. Features. Typical Applications. General Description

HMC659LC5 LINEAR & POWER AMPLIFIERS - SMT. GaAs PHEMT MMIC POWER AMPLIFIER, DC - 15 GHz. Features. Typical Applications. General Description v.61 Typical Applications The wideband PA is ideal for: Telecom Infrastructure Microwave Radio & VSAT Military & Space Test Instrumentation Fiber Optics Functional Diagram Features P1dB Output Power: +27.5

More information

Ultralow Distortion Current Feedback ADC Driver ADA4927-1/ADA4927-2

Ultralow Distortion Current Feedback ADC Driver ADA4927-1/ADA4927-2 FEATURES Extremely low harmonic distortion 117 HD2 @ 10 MHz 85 HD2 @ 70 MHz 75 HD2 @ 100 MHz 122 HD3 @ 10 MHz 95 HD3 @ 70 MHz 85 HD3 @ 100 MHz Better distortion at higher gains than F amplifiers Low input-referred

More information

Features. = +25 C, Vdd1 = Vdd2 = +3.5V, Idd = 80 ma [2]

Features. = +25 C, Vdd1 = Vdd2 = +3.5V, Idd = 80 ma [2] Typical Applications This is ideal for: Features Low Noise Figure: 1.8 db Point-to-Point Radios Point-to-Multi-Point Radios Military & Space Test Instrumentation Functional Diagram High Gain: 19 db High

More information

Features OBSOLETE. = +25 C, 50 Ohm system, Vdd = +5V. Parameter Frequency Min. Typ. Max. Units GHz

Features OBSOLETE. = +25 C, 50 Ohm system, Vdd = +5V. Parameter Frequency Min. Typ. Max. Units GHz Typical Applications v.91 ATTENUATOR,.5-6. GHz Features The is ideal for: Point-to-Point Radio Cellular/3G & WiMAX/4G Infrastructure Test Instrumentation Microwave Sensors Military, ECM & Radar Functional

More information