ADA Barrier-Free Bathware for Assisted Living

Transcription

1 This continuing education program is sponsored and provided to you due to the professional courtesy of: ADA Barrier-Free Bathware for Assisted Living Clarion Bathware 44 Amsler Ave. Shippenville, PA Tel. : Fax : 1 (814) Web Site: Fill out form MRS001 AIA-CB2201-W The material contained in this continuing education program belongs to Clarion Bathware. Questions or concerns about the program content need to be addressed with the program instructor. Powered by 1

2 Promotional Statement Slide This course has been design as a structured asynchronous program therefore has been formatted for online use only. Please don t forget to print your AIA/CES Certificate of Completion. Successful completion is scoring 80% or higher on your final exam. If you wish to print later you can access all certificates from you re A-F transcript center. The American Institute of Architects Course No. CB2201-W; LUs This program qualifies for HSW credit Architect-Forum is a registered provider with The American Institute Of Architects Continuing Education Systems. Credit earned on completion of this program will be reported to CES Records for AIA members. Certificates Of Completion for non-aia members available on request. This program is registered with the AIA/CES for continuing professional education. As such, it does not include content that may be deemed or construed to be an approval or endorsement by the AIA of any material of construction or any method or manner of handling, using, distributing, or dealing in any material or product. Questions related to specific materials, methods, and services will be addressed at the conclusion of this presentation.

3 Presenter Bio If you are in the state of California or any other state that requires the Trainer Educator's Knowledge & Experience Background please click on the following link to download a PDF version of the Bio. Click here download Presenter: Arthur Lee Wentling

4 Learning Objectives At the conclusion of this program the designer will have gained knowledge and understanding over the following: 1. The different Codes and Regulations that govern compliance. 2. ADA requirements for shower stalls. 3. Available ADA compliant shower stalls. 4. Understanding the proper applications for different ADA complaint showers. 5. Barrier Free Shower/Tubs Case Studies

5 ADAAG Codes and Regulations

6 Many Codes to deal with Americans Disabilities Act 1991 (ADAAG) Architectural Barriers Act 1968 (ABA) International Code Council (ICC/ANSI A ) International Plumbing Code (IPC- 2006) Uniform Plumbing Code (IAPMO/ANSI UPC ) International Building Code (2006 IBC) Uniform Federal Accessibility Standards (UFAS) Fair Housing Act (HUD)

7 Codes in Conflict ADA, ANSI, UPC, IBC... Standardizing various codes. Impossible for a person to comply with two different bodies who interpreted the code in different manners.

8 Which code to use!!!! ADA is Minimum Requirement for many projects The particular code or codes, relevant to your project may depend on the particular location of the project. Check with the local code officials office for particulars. The code official is often your best ally. Often multiple codes such as ANSI, ADA and UPC can be intermingled and make compliance challenging.

9 ADA Requirements For Shower Stalls

10 ADA Specifics Changes in Level Clear Floor Space for Tubs 36 x 36 Transfer showers 60 x 30 showers 60 x 36 showers Grab Bars Seats

11 Changes In Level- ¼ 303 Changes in Level Vertical. Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical. Vertical Change in Level

12 Changes in Level- ½ Beveled. Changes in level between 1/4 inch (6.4 mm) high minimum and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2. Advisory Beveled. A change in level of 1/2 inch (13 mm) is permitted to be ¼ inch (6.4 mm) vertical plus ¼ inch (6.4 mm) beveled. However, in no case may the combined change in level exceed 1/2 inch (13 mm). Changes in level exceeding 1/2 inch (13 mm) must comply with 405 (Ramps) or 406 (Curb Ramps). Beveled Change in Level

13 Clear Floor Space at Bathtubs Clearance. Clearance in front of bathtubs shall extend the length of the bathtub and shall be 30 inches (760 mm) wide minimum. A lavatory complying with 606 shall be permitted at the control end of the clearance. Where a permanent seat is provided at the head end of the bathtub, the clearance shall extend 12 inches (305 mm) minimum beyond the wall at the head end of the bathtub.

14 Grab bars for tubs with permanent seats Bathtubs With Permanent Seats. For bathtubs with permanent seats, grab bars shall be provided in accordance with Back Wall. Two grab bars shall be installed on the back wall, one located in accordance with and the other located 8 inches (205 mm) minimum and 10 inches (255 mm) maximum above the rim of the bathtub. Each grab bar shall be installed 15 inches (380 mm) maximum from the head end wall and 12 inches (305 mm) maximum from the control end wall Control End Wall. A grab bar 24 inches (610 mm) long minimum shall be installed on the control end wall at the front edge of the bathtub.

15 Grab bars for tubs without permanent seat Bathtubs Without Permanent Seats. For bathtubs without permanent seats, grab bars shall comply with Back Wall. Two grab bars shall be installed on the back wall, one located in accordance with and other located 8 inches (205 mm) minimum and 10 inches (255mm) maximum above the rim of the bathtub. Each grab bar shall be 24 inches (610 mm) long minimum and shall be installed 24 inches (610 mm) maximum from the head end wall and 12 inches (305 mm) maximum from the control end wall Control End Wall. A grab bar 24 inches (610 mm) long minimum shall be installed on the control end wall at the front edge of the bathtub Head End Wall. A grab bar 12 inches (305 mm) long minimum shall be installed on the head end wall at the front edge of the bathtub.

16 Control Location Controls. Controls, other than drain stoppers, shall be located on an end wall. Controls shall be between the bathtub rim and grab bar, and between the open side of the bathtub and the centerline of the width of the bathtub. Controls shall comply with Shower Spray Unit and Water. A shower spray unit with a hose 59 inches (1500 mm) long minimum that can be used both as a fixedposition shower head and as a hand held shower shall be provided. The shower spray unit shall have an on/off control with a non-positive shutoff. If an adjustable-height shower head on a vertical bar is used, the bar shall be installed so as not to obstruct the use of grab bars. Bathtub shower spray units shall deliver water that is 120 F (49 C) maximum.

17 Transfer Shower Stalls Transfer Type Shower Compartments. Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915 mm) wide minimum entry on the face of the shower compartment. Clearance of 36 inches (915 mm) wide minimum by 48 inches (1220 mm) long minimum measured from the control wall shall be provided.

18 Standard Roll In Shower Stalls Standard Roll-In Type Shower Compartments. Standard roll-in type shower compartments shall be 30 inches (760 mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides and shall have a 60 inches (1525 mm) wide minimum entry on the face of the shower compartment. Standard Roll-In-Type Shower Compartment Size and Clearance

19 Alternate Roll In Shower Stall Alternate Roll-In Type Shower Compartments. Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides. A 36 inch (915 mm) wide minimum entry shall be provided at one end of the long side of the compartment.

20 Transfer Shower Grab Bars Transfer Type Shower Compartments. In transfer type compartment, grab bars shall be provided across the control wall and back wall to a point 18 inches (455 mm) from the control wall. ICC/ANSI A Requires vertical 18 bar on control wall 4 from outside edge above horizontal bar.

21 Grab Bars Roll-In Shower Stall Standard Roll-In Type Shower Compartments. Where a seat is provided in standard roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall opposite the seat. Grab bars shall not be provided above the seat. Where a seat is not provided in standard roll-in type shower compartments, grab bars shall be provided on three walls. Grab bars shall be installed 6 inches (150 mm) maximum from adjacent walls.

22 Grab Bars Alternate Roll In Alternate Roll-In Type Shower Compartments. In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry. Grab bars shall not be provided above the seat. Grab bars shall be installed 6 inches (150 mm) maximum from adjacent walls. Grab Bars for Alternative Roll-In-Type Showers

23 Transfer Type Control Location Transfer Type Shower Compartments. In transfer type shower compartments, the Controls, faucets, and shower spray unit shall be installed on the side wall opposite the seat 38 inches (965 mm) minimum and 48 inches (1220 mm) maximum above the shower floor and shall be located on the control wall 15 inches (380 mm) maximum from the centerline of the seat toward the shower opening. Transfer Type Shower Compartment Control Location

24 Standard Roll In Shower Controls Standard Roll-In Type Shower Compartments. In standard roll-in type shower compartments, the controls, faucets, and shower spray unit shall be located above the grab bar, but no higher than 48 inches (1220 mm) above the shower floor. Where a seat is provided, the controls, faucets, and shower spray unit shall be installed on the back wall adjacent to the seat wall and shall be located 27 inches (685 mm) maximum from the seat wall. Advisory Standard Roll-in Type Shower Compartments. In standard roll-in type showers without seats, the shower head and operable parts can be located on any of the three walls of the shower without adversely affecting accessibility.

25 Alternate Roll In Controls Alternate Roll-In Type Shower Compartments. In alternate roll-in type shower compartments, the controls, faucets, and shower spray unit shall be located above the grab bar, but no higher than 48 inches (1220 mm) above the shower floor. Where a seat is provided, the controls, faucets, and shower spray unit shall be located on the side wall adjacent to the seat 27 inches (685 mm) maximum from the side wall behind the seat or shall be located on the back wall opposite the seat 15 inches (380 mm) maximum, left or right, of the centerline of the seat. Where a seat is not Provided, the controls, faucets, and shower spray unit shall be installed on the side wall farthest from the compartment entry. Alternate Roll-In Type Shower Compartment Control Location

26 Shower Spray Unit and Thresholds Shower Spray Unit and Water. A shower spray unit with a hose 59 inches (1500 mm) long minimum that can be used both as a fixed-position shower head and as a hand-held shower shall be provided. The shower spray unit shall have an on/off control with a nonpositive shut-off. If an adjustable-height shower head on a vertical bar is used, the bar shall be installed so as not to obstruct the use of grab bars. Shower spray units shall deliver water that is 120 F (49 C) maximum. EXCEPTION: A fixed shower head located at 48 inches (1220 mm) maximum above the shower finish floor shall be permitted instead of a hand-held spray unit in facilities that are not medical care facilities, long-term care facilities, transient lodging guest rooms, or residential dwelling units. Advisory Shower Spray Unit and Water. Ensure that hand-held shower spray units are capable of delivering water pressure substantially equivalent to fixed shower heads Thresholds. Thresholds in roll-in type shower compartments shall be 1/2 inch (13 mm) high maximum in accordance with 303. In transfer type shower compartments, thresholds 1/2 inch (13 mm) high maximum shall be beveled, rounded, or vertical. EXCEPTION: A threshold 2 inches (51 mm) high maximum shall be permitted in transfer type shower compartments in existing facilities where provision of a 1/2 inch (13 mm) high threshold would disturb the structural reinforcement of the floor slab.

27 Grab Bars-Circular and Non-Circular Circular Cross Section. Grab bars with circular cross sections shall have an outside diameter of 1 1/4 inches (32 mm) minimum and 2 inches (51 mm) maximum Non-Circular Cross Section. Grab bars with noncircular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (100 mm) minimum and 4.8 inches (120 mm) maximum. Please see figure

28 Grab Bar Spacing Spacing. The space between the wall and the grab bar shall be 1 1/2 inches (38 mm). The space between the grab bar and projecting objects below and at the ends shall be 1 1/2 inches (38 mm) minimum. The space between the grab bar and projecting objects above shall be 12 inches (305 mm) minimum, EXCEPTION: The space between the grab bars and shower controls, shower fittings, and other grab bars above shall be permitted to be 1 1/2 inches (38 mm) minimum.

29 Grab Bar Position/Strength Position of Grab Bars. Grab bars shall be installed in a horizontal position, 33 inches (840 mm) minimum and 36 inches (915 mm) maximum above the finish floor measured to the top of the gripping surface, except that at water closets for children's use complying with 604.9, grab bars shall be installed in a horizontal position 18 inches (455 mm) minimum and 27 Inches (685 mm) maximum above the finish floor measured to the top of the gripping surface. The height of the lower grab bar on the back wall of a bathtub shall comply with or Structural Strength. Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the grab bar, fastener, mounting device, or supporting structure.

30 Bathtub Seats Bathtub Seats. The top of bathtub seats shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the bathroom finish floor. The depth of a removable in-tub seat shall be 15 inches (380 mm) minimum and 16 inches (405 mm) maximum. The seat shall be capable of secure placement. Permanent seats at the head end of the bathtub shall be 15 inches (380 mm) deep minimum and shall extend from the back wall to or beyond the outer edge of the bathtub.

31 Shower Seats Shower Compartment Seats. Where a seat is provided in a standard roll-in shower compartment, it shall be a folding type, shall be installed on the side wall adjacent to the controls, and shall extend from the back wall to a point within 3 inches (75 mm) of the compartment entry. Where a seat is provided in an alternate roll-in type shower compartment, it shall be a folding type, shall be installed on the front wall opposite the back wall, and shall extend from the adjacent side wall to a point within 3 inches (75 mm) of the compartment entry. In transfer-type showers, the seat shall extend from the back wall to a point within 3 inches (75 mm) of the compartment entry. The top of the seat shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the bathroom finish floor. Seats shall comply with or

32 Rectangular Seat Rectangular Seats. The rear edge of a rectangular seat shall be 2 1/2 inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall. The side edge of the seat shall be 1 1/2 inches (38 mm) maximum from the adjacent Wall.

33 L Shaped Seats L-Shaped Seats. The rear edge of an L-shaped seat shall be 2 1/2, inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall. The rear edge of the L" portion of the seat shall be 1 1/2, inches (38 mm) maximum from the wall and the front edge shall be 14 inches (355 mm) minimum and 15 inches (380 mm) maximum from the wall. The end of the L" shall be 22 inches (560 mm) minimum and 23 inches maximum (585 mm) from the main seat wall.

34 Bariatric Seat New Seat Bolted through wall Four legs to support weight 550 pound recommended weight limit Folds up Old Seat Bolted through wall Wall section provided strength Folds up

35 Available ADA Compliant Shower Stalls Barrier Free Showers ¾ Barrier Free Showers Convertible Showers Accessorized Showers & Tub/Showers

36 The Challenge Aging process causes challenges in dexterity, balance especially around the tub/shower area. Age advancement makes mobility and maneuvering in the shower/tub area very difficult. We want luxury within the budget. To stay within budget, not only the products and design, but also the installation must be straightforward and reliable, particularly if it s non-traditional.

37 What is assisted living? Residents have as much independence as they want Personal care and support services Assisted living communities are designed to provide residents with assistance with basic activities of daily living such as bathing, grooming, dressing, and more.

38 Transfer Type Showers 36"x36" Transfer showers designed for new construction feature folding seat, 1-1/2" stainless steel grab bars, pressure balanced mixing valve, and hand held shower. Standard Features: Fiberglass reinforced gel coat construction 1-piece shower 3/4" barrier-free threshold Slip-resistant, textured floor Center drain location White, biscuit, bone, or sterling silver finish Complies with NAHB, HUD UM-73A, and ANSI- Z124.2 Complies with ADAAG and ANSI A117.1 when properly accessorized 3 year warranty

39 Barrier Free Available Dimension 36.0" W x 36.75" D x 77.0" H 36" Barrier-free Shower w/2" Threshold 38.0" W x 38.0" D x 78.25" H 38" ADA-Compliant 1-Piece Barrier-free Transfer Shower w/2" Threshold 40.0" W x 39.0" D x 79.0" H 40" ADA-Compliant 1-Piece Barrier-free Transfer Shower w/2" Threshold 40.0" W x 39.0" D x 79.0" H 40" ADA-Compliant 3-Piece Barrier-free Transfer Shower w/2" Threshold 42.25" W x 37.0" D x 84.75" H 40" 1-Piece Acrylic Barrier-free Shower w/seat & 2" Threshold 42.25" W x 37.0" D x 84.75" H 40" ADA-Compliant 1-Piece Acrylic Barrier-free Shower w/2" Threshold 44.0" W x 51.0" D x 77.5" H 44" 3-Piece Barrier-free Shower w/2" Threshold 48.0" W x 36.0" D x 78.0" H 48" Barrier-free Shower w/2" Threshold 50.0" W x 51.0" D x 77.75" H 50" Barrier-free Shower w/2" Threshold 53.75" W x 36.0" D x 85.5" H 51 1/2" 1-Piece Acrylic Barrier-free Shower w/2" Threshold 53.75" W x 36.0" D x 85.5" H 51 1/2" 1-Piece Acrylic Barrier-free Shower w/seat & 2" Threshold " W x 36.75" D x 78.0"H 60" 1-Piece Barrier-free Shower w/seat & 2" Threshold 59.75" W x 33.0" D x 77.75" H 60" 3-Piece Barrier-free Shower w/2" Threshold - Left or Right Hand Drain 59.75" W x 33.0" D x 77.75" H 60" 1-Piece Barrier-free Shower w/2" Threshold 60.0" W x 36.0" D x 78.0" H 60" 1-Piece Barrier-free Shower w/2" Threshold 60.0" W x 36.0" D x 78.0" H 60" 3-Piece Barrier-free Shower w/2" Threshold 62.0" W x 36.0" D x 84.5" H 60" 1-Piece Acrylic Barrier-free Shower w/2" Threshold 62.0" W x 36.0" D x 84.5" H 60" 1-Piece Acrylic Barrier-free Shower w/seat & 2" Threshold 62.75" W x 33.5" D x 77.75" H 63" ADA-Compliant 1-Piece Roll-in Shower w/2" Threshold 65.0" W x 33.0" D x 84.5" H 63" ADA-Compliant 1-Piece Acrylic Barrier-free Roll-in Shower w/2" Threshold 65.25" W x 36.0" D x 85.0" H 63" ADA-Compliant 1-Piece Acrylic Barrier-free Roll-in Shower w/2" Threshold

40 Roll-In Showers 60"x30" Roll-In showers with 3/4" barrier free design can accommodate a wheel chair and are manufactured to meet ADA specifications. Standard Features: Fiberglass reinforced gel coat construction 1-piece shower 3/4" barrier-free threshold Slip-resistant, textured floor Center drain location White, biscuit, bone, or sterling silver finish Complies with NAHB, HUD UM-73A, and ANSI- Z124.2 Complies with ADAAG and ANSI A117.1 when properly accessorized 3 year warranty ADA

41 ¾ Barrier Free Available Dimension 38.0" W x 38.0" D x 78.0" H 38" ADA-Compliant 1-Piece Barrier-free Transfer Shower w/3/4" Threshold 40.0" W x 39.0" D x 78.25" H 40" ADA-Compliant 1-Piece Transfer Shower w/return Flange & 3/4" Threshold 40.0" W x 39.0" D x 78.25" H 40" ADA-Compliant 1-Piece Tiled Barrier-free Transfer Shower w/3/4" Threshold 40.0" W x 39.0" D x 78.25" H 40" ADA-Compliant 1-Piece Barrier-free Transfer Shower w/3/4" Threshold 40.0" W x 39.0" D x 78.25" H 40" ADA-Compliant 3-Piece Barrier-free Transfer Shower w/3/4" Threshold 40.0" W x 39.0" D x 78.25" H 40" ADA-Compliant 3-Piece Barrier-free Transfer Shower w/3/4" Threshold 42.25" W x 37.0" D x 83.5" H 40" ADA-Compliant 1-Piece Acrylic Transfer Shower w/3/4" Threshold 42.25" W x 37.0" D x 83.5" H 40" 1-Piece Acrylic Barrier-free Transfer Shower w/seat & 3/4" Threshold 48.0" W x 36.0" D x 78.0" H 48" Barrier-free Shower w/3/4" Threshold 48.0" W x 36.0" D x 78.0" H 48" 3-Piece Barrier-free Shower w/3/4" Threshold 50.0" W x 39.0" D x 81.75" H 50" 1-Piece Tiled Barrier-free Shower w/return Flange & 3/4" Threshold 60.0" W x 36.0" D x " H 60" 1-Piece Barrier-free Shower w/3/4" Threshold 60.5" W x 32.0" D x 17.5" H Tub insert for Convertible Shower 62.0" W x 34.0" D x 85.0" H 60" Acrylic Tub-Shower - Left or Right Hand Drain 63.0" W x 33.75" D x 78.0" H 63" ADA-Compliant 1-Piece Roll-in Shower w/3/4" Threshold 63.0" W x 33.75" D x 78.0" H 63" ADA-Compliant 1-Piece Tiled Roll-in Shower w/3/4" Threshold 64.0" W x 36.0" D x 78.0" H 64" ADA-Compliant 3-Piece Roll-in Shower w/3/4" Threshold 64.0" W x 36.0" D x 78.0" H 64" ADA-Compliant 1-Piece Roll-in Shower w/3/4" Threshold 65.0" W x 33.0" D x 83.25" H 63" ADA-Compliant 1-Piece Acrylic Barrier-free Roll-in Shower w/3/4" Threshold 65.25" W x 36.0" D x 83.75" H 63" ADA-Compliant 1-Piece Acrylic Barrier-free Roll-in Shower w/3/4" Threshold 66.0" W x 35.0" D x 78.0" H 66" Convertible Shower. Accepts model 6635TX34 Tub Insert which converts this Shower to a Tub-Shower

42 Convertible Showers These shower stalls give the user the ability to convert the shower stall to a tub/shower combination at a later date without major renovation to their bathroom.

43 Convertible Models 60.0" W x 35.0" D x 78.0" H 60" Convertible Shower Accepts model 6035T Tub Insert which converts this Shower to a Tub-Shower 60.0" W x 43.0" D x " H 60" Convertible Shower. Accepts model 6043T Tub Insert which converts this Shower to a Tub-Shower 66.0" W x 35.0" D x 78.0" H 66" Convertible Shower. Accepts model 6635TX34 Tub Insert which converts this Shower to a Tub-Shower

44 Accessorized Showers & Tub/Showers Accessories offered on these units include that help enhance the safety of the end users include 1.5 stainless steel grab bars with 3 X 3 steel backing plates, Fold up naugahyde or phenolic seat, Pressure balanced mixing valves, Hand held shower and glide bar, Soap dishes, curtain rods and more. Note: Slip-resistant floors are standard in all assisted living models.

45 Barrier Free Shower/Tubs Case Studies Now that we have learned about ADA requirements and available barrier free shower/tubs let take a look at some barrier free shower case studies.

46 Saint Vincent Project Case Study 1 Unit Type: Barrier-free Shower /ADA Compliant Project Location: Saint Vincent Erie/PA Saint Vincent is a community hospital that added a new wing and mother and baby delivery center. 46

47 Saint Vincent Project Case Study 1 Barrier-free Shower 40" 1-Piece Acrylic Barrier-free Shower w/seat & 2" Threshold Dimensions: 42.25" W x 37.0" D x 84.75" H Metric: 1073mm W x 939mm D x 2152mm H Standard Features: 1-piece seamless shower 2" threshold Acrylic surface provides long-lasting, durable finish Fiberglass reinforced for added strength Molded seat located opposite valve wall Center drain location White or bone finish Complies with NAHB, HUD UM-73A, and ANSI-Z year warranty 47

48 Erickson Retirement Project Case Study 2 Unit Type: Convertible Shower, Tub Insert, and Barrier-free Shower. Project Location: Erickson Retirement/PA 48

49 Erickson Retirement Project Case Study 2 Convertible Shower Dimensions: 60.0" W x 35.0" D x 78.0" H Metric: 1524mm W x 889mm D x 1981mm H Standard Features: Fiberglass reinforced gel coat construction 1-piece convertible shower Molded soap ledges Slip-resistant, textured floor Center drain location White, biscuit, bone, or sterling silver finish Complies with NAHB, HUD UM-73A, and ANSI-Z

50 Erickson Retirement Project Case Study 2 Tub Insert Dimensions: " W x 32.0" D x 15.0" H Metric: 1431mm W x 812mm D x 381mm H Gallon Capacity: 35.0 US Gallons Standard Features: Fiberglass reinforced gel coat construction Allows to be converted into a tub-shower combination Slip-resistant, textured floor Center drain location White, biscuit, bone, or sterling silver finish Complies with NAHB, HUD UM-73A, and ANSI-Z year warranty 50

51 Program Summary By now you should have gained knowledge and understanding over the following: 1. The different Codes and Regulations that govern compliance. 2. ADA requirements for shower stalls. 3. Available ADA compliant shower stalls. 4. Understanding the proper applications for different ADA complaint showers. 5. Barrier Free Shower/Tubs Case Studies

52 Questions For The Next Ten Minutes This concludes the course material. The following ten minutes will be for taking a short exam. You must complete the exam with a 80% or higher in order to receive credit. Please make sure and print your certificates of completion either for AIA/CES, CSI/CEN or for state MCE credit.

53 Course Handout in PDF Format If you would like to save an Adobe PDF copy of this course please click on the link provided on this slide. Reasons why you might want a copy of this program. To reference the material at a later date. If you are working on a project and need to access the information to refresh your memory. Great way of using to review the material while you take the test. Please click here to access the Adobe Acrobat version of this course. Note: We recommend you create a folder on your computer and save all of Architect- Forum handouts for future reference.

54 ADA Barrier-Free Bathware for Assisted Living This continuing education program is sponsored and provided to you due to the professional courtesy of: This concludes the continuing education program. Please proceed to take the exam. Clarion Bathware 44 Amsler Ave. Shippenville, PA Tel. : Fax : 1 (814) Web Site: Fill out form Thank You For Your Time! MRS001 AIA-CB2201-W The material contained in this continuing education program belongs to Clarion Bathware. Questions or concerns about the program content need to be addressed with the program instructor. Powered by 54

55 Quiz Instructions CB2201-W-Quiz In order for you to get credit for this program you must successfully complete the following short exam. Pass for this exam is 80% or higher. Please make sure and print your certificates of completion either for AIA/CES or for state MCE credit. Please print your Certificate of Completion upon successful completion. You can print the certificate from your A-F transcript any time after completion. If your colleagues can benefit from this course, please let them know. Feel free to revisit the Architect-Forum LMS elearning System to take additional courses.

56 Accessing the Course Exam Take Test To complete the course and get credit you must successfully complete the short course exam with an 80% or higher. You can access the test from this PDF or through the Flash based version. Please click on the Test Button below to get started. After clicking on the button you must scroll down the page and click on the Start test button. If you need help please , call or use our online chat support. If you need to see our help page please click here. Note: Cookies and JavaScript must me enabled in your browser, see help link to make sure its set on your browser.