Rickenbacker Road. Bell, CA

Transcription

1 Rickenbacker Road Bell, CA Landmark Signs, Inc. 2014

2 T ABLE OF CONTENTS & PROGRAM DIRECTORY General Information Occupant Procedures & Requirements Minimum Sign Standards Prohibited Signs Pages: A1 A2 A3 Project Site Plan 5390 & Pages: A1 A2 Corporate Wall Signs Allowable Parameters Typical Allowable Sign Areas Corporate Monument Sign Building Address Sign Allowable Parameters Specifications & Dimensions Allowable Parameters Specifications & Dimensions Allowable Location Elevations Developer Building Sign Commemorative Sign Allowable Parameters Specifications & Dimensions Allowable Location Elevation Allowable Parameters Specifications & Dimensions B1 B2 - B6 C1 C2 D1 D2 D3 & D4 E1 E2 E3 F1 F2 Approved Sign Contractor / Consultant: Developer: Pacific Industrial 6272 E. Pacific Coast Hwy., Suite E. Long Beach, CA Contact: Emily Mandrup emilym@pac-industrial.comee Phone: Landmark Signs 2456 N. Glassell St., Suite A Orange, CA Contact: John Myres johnm@landmarksignsinc.com Cell: Phone: Fax: City Planning: City of Bell Community Development 6330 Pine Ave. Bell, CA Contact: Joe Perez jperez@cityofbell.orgee Phone: Fax:

3 GENERAL INFORMATION OCCUPANT PROCEDURES & REQUIREMENTS 1. Building occupant shall not install any sign without all required permits from any local authority holding jurisdiction over such work. 2. In the event of any future modifications, revisions or changes to the Building Occupant s lawfully permitted signs, Occupant shall abide by all of the regulations of this Sign Program and reapply for any required permits. 3. Building occupant s contractors and their agents must be lawfully licensed and bonded according to the State Contractors License Law and possess a minimum of 2 million dollars general liability insurance. 4. All sign work must comply with every required building and electrical code. 5. All ground signs must be engineered by a California State licensed engineer. 6. Occupant shall be responsible for all costs associated with the manufacture, installation, maintenance and removal of their signs, including but not limited to, permits, engineering, designs, corrections, building modifications necessary for electrical or service access, repairs, cleaning, refinishing, refurbishing, personal or property damage as a result of sign malfunctions, sign removal and disposal resulting from violation of the regulations of this Sign Program, and sign removal and repair of building damage after vacancy. 7. Within 30 days of vacating premises or loss of lease, Occupant shall completely remove and dispose of all of Occupant s signs and restore the building surfaces to their original condition. A3 A1

4 GENERAL G IINFORMATION MINIMUM SIGN STANDRDS All signs shall be manufactured and installed according to the following minimum standards: A. Signs shall be in compliance with U. L. Laboratories, the National Electric Code (NEC), the Uniform Building Code (ICBO) and any other Federal, State and Local building codes that are required. B. Electrical Signs shall bear U. L. labels applied by an U. L. Laboratories licensed manufacturer, Manufacturer's labels and Permit Stickers (where required). Manufacturer's labels shall not be visible from parking or the street, or from any normal viewing angle. Permit Stickers shall be applied with minimum visibility so as to only comply with the local authority's minimum placement requirements. C. All sign companies and their agents shall be lawfully licensed and bonded according to the State Contractor's Board requirements and with any local authorities where licensing is required. All sign companies and their agents shall be insured with a minimum of 2 million dollars general liability insurance. D. No sign shall be installed without Permits from every appropriate local authority and without required preliminary or final inspections, such inspections having been completed within 90 days of the commencement of the sign installation. E. All signs shall be manufactured and installed according to the highest sign industry standards, using the best quality materials and utilizing the best processes available at the time the work occurs. stainless steel or zinc coated to prevent rust. G. Signs must be fabricated with little or no visibility of seams, welds or fasteners. All exposed seams must be filled flush and finished so as to be an invisible part of their adjacent surfaces. All exposed welds must be ground smooth and finished so as to be an invisible part of their adjacent surfaces. All exposed fasteners such as rivets and screws must be flush, filled and finished so as to be an invisible part of their adjacent surfaces. H. Signs must use a minium.080" depth of material on any flat, exposed surfaces, and greater depth is required to eliminate "oil canning", any noticeable warping or visibility of any interior frame attachments. I. No exposed angle clips or black iron may be used as installation hardware. Installation parts must be hidden when possible, and when exposed (such as spacers) to any angle of view, must be painted to match either the building wall or the adjacent sign surface. J. Painted finishes must be smooth and uniformly covered, without intermittent orange peel, drips or runs and remain free from blistering, peeling, chipping or fading for a minimum of 1-year from the commencement of installation. Enamel paints must be of automotive quality and all painted finishes must be applied using the paint manufacturer's recommended methods, preconditioning and primers. K. No color hues and finishes prone to early fading may be used. All exposed metals, plastics, vinyls, including printed vinyls and other parts must be L. Internal lighting must be uniform and free of "hot spots" or shadowing. Fluorescent lamps must be either single pin or high output and placed with a minimum on center distance of 12" apart and 6" from the interior sign edge. Neon transformers must be 30 MA, and neon must be placed with a minimum on center distance of 5" apart and 2 ½ " distance from the interior sign edge. LED lighting must be 5 watts per unit, minimum. Light leaks are not permitted. M. Exposed neon housings, supports, backs, crossovers and returns must be painted with opaque paint to match the adjacent sign surface. N. Exposed conduits, junction boxes or electrical parts are not permitted. A2

5 GENERAL INFORMATION PROHIBITED SIGNS Any sign of the following types or specifications shall be prohibited: 1. Signs advertising any entity, products, events or subjects unrelated to the property upon which said sign is located. This includes but is not limited to Outdoor Advertising, Billboards and Off-Site signs of all types. 2. Roof signs or signs projecting above a building parapet or roof line. 3. Signs that constitute a traffic hazard by using symbols, colors, designs or words commonly used on traffic signs and signals in such a manner as to interfere with, mislead or confuse pedestrian or automotive traffic. 4. Signs that flash, make audible sounds, or have animation; or have parts that do so. are attached to or interfere with any public utility. 9. Portable signs, Sandwich Board signs or inflatable displays. 10. Holiday lighting, light bulb strings or the like. 11. Signs displaying profanity, obscene images or immoral content as deemed so by the Property Owner. 12. Signs affixed to any parts of the buildings or premises that are not a normally acceptable location for signs such as but not limited to, stand pipes and drains, roofing or roof equipment, roof or parapet flashing, window frames, awnings and canopies, light standards, poles or sign posts. 13. Signs left abandoned beyond 30 days after an occupant vacates a property. Program. 18. Any sign not allowed in this Sign Program with the exception of: Non-illuminated directional wall or informational signs labeling Shipping and Receiving, Will Call or loading docks, and containing opening hours, contact information or rules and regulations of the like, not to exceed 6 square feet in area. 5. Signs affixed to vehicles (aside from those used exclusively for delivery) for the purpose of advertising any entity, product, event or subject whether related or unrelated to the property upon which such vehicle is parked. Such vehicles may be towed away at the vehicle owner's expense. 6. Temporary signs such as but not limited to banners, flags, pennants or balloons unless specifically allowed by and in accordance with the code of the local authority. 7. Signs that violate any law or regulation whether Federal, State or Local. 14. Signs in unclean condition or in need of repair or maintenance for a period not to exceed 30 days. 15. Window signs including but not limited to neon displays, neon window borders, lighted cabinets, non-illuminated vinyl, printed or painted graphics or lettering. 16. Paper, cardboard or foam core signs, decals or stickers, graffiti, or any sign that defaces property. Perpetrators of such signs may be liable to arrest and prosecution. 17. Any sign prohibited according to the City of Bell codes that are current to the publication of this Sign A3

6 CORPORATE WALL SIGNS ALLOWABLE PARAMETERS Permitted Sign Type: Quantity allowed: Locations: Maximum Sign Height: Maximum Length: Maximum Sign Area: Sign Design and Color: Allowable Copy & Graphics: Sign Materials & Lighting: Individual illuminated or non-illuminated standard or reverse channel letters and logos. One per building elevation, per lease-holding tenant. Where indicated within Signable Areas where indicated on building elevations on pages B2 - B6. Any combination of individual letters or logos not to exceed 7' in overall height. Any combination of individual letters or logos not to exceed the lengths indicated within Signable Areas on pages B2 - B6. Total sign area per lease-holding tenant not to exceed 4 square feet per foot of adjacent street or freeway frontage. May be according to occupant s own design. All signs must be approved in writing by the Landlord prior to installation. Restricted to corporate or business name and logo, no products or services to be advertised. Letters (illuminated or non-illuminated) must be fabricated from a minimum of.080 aluminum, 3" deep. Illumination must be from internal LED light sources. Landmark Signs, Inc B1

7 5390 CORPORATE WALL SIGNS TYPICAL ALLOWABLE SIGN AREAS 36' Maximum Length Sign must be centered horizontally on window vertical center line. 7' Maximum Height 5390 Rickenbacker, North Elevation, East End Scale: 1" = 25'-0" Key: Signable Area Sign must be centered horizontally on window vertical center line. 7' Maximum Height 52' Maximum Length Horizontal Center Line (Signs must be centered vertically here when indicated). Vertical Center Line (Signs must be centered horizontally here when indicated) Rickenbacker, East Elevation, North Corner Scale: 1" = 25'-0" Landmark Signs, Inc B2

8 5390 CORPORATE WALL SIGNS TYPICAL ALLOWABLE SIGN AREAS 62' Maximum Length 7' Maximum Length 5390 Rickenbacker, West Elevation Scale: 1" = 25'-0" Key: Signable Area 7' Maximum Height ual 62' Maximum Length ual Horizontal Center Line (Signs must be centered vertically here when indicated). Vertical Center Line (Signs must be centered horizontally here when indicated) Rickenbacker, South Elevation Scale: 1" = 25'-0" Landmark Signs, Inc B3

9 5630 CORPORATE WALL SIGNS TYPICAL ALLOWABLE SIGN AREAS 52' Maximum Length Sign must be centered horizontally on window vertical center line. ual 7' Maximum Height ual 5630 Rickenbacker, East Elevation, South Corner Scale: 1" = 25'-0" Key: Signable Area 18' Maximum Length ual 7' Maximum Height ual Horizontal Center Line (Signs must be centered vertically here when indicated). Vertical Center Line (Signs must be centered horizontally here when indicated) Rickenbacker, South Elevation, East End Scale: 1" = 25'-0" Landmark Signs, Inc B4

10 5630 CORPORATE WALL SIGNS TYPICAL ALLOWABLE SIGN AREAS 48' Maximum Length Sign must be centered vertically on this horizontal center line. 7'-6" to Center Line 7' Maximum Height 5630 Rickenbacker, North Elevation, East End Scale: 1" = 25'-0" Key: Signable Area Sign must be centered vertically on this horizontal center line. 7' Maximum Height 7'-6" to Center Line 52' Maximum Length Horizontal Center Line (Signs must be centered vertically here when indicated). Vertical Center Line (Signs must be centered horizontally here when indicated) Rickenbacker, East Elevation, North Corner Scale: 1" = 25'-0" Landmark Signs, Inc B5

11 5630 CORPORATE WALL SIGNS TYPICAL ALLOWABLE SIGN AREAS Sign must be centered horizontally on window vertical center line. 52' Maximum Length ual 7' Maximum Height ual 5630 Rickenbacker, North Elevation, West End Scale: 1" = 25'-0" Key: Signable Area 31' Maximum Length ual 7' Maximum Height ual Horizontal Center Line (Signs must be centered vertically here when indicated). Vertical Center Line (Signs must be centered horizontally here when indicated) Rickenbacker, West Elevation Scale: 1" = 25'-0" B6 Landmark Signs, Inc. 2014

12 PROJECT MONUMENT SIGN ALLOWABLE PARAMETERS Permitted Sign Type: Specifications: Quantity allowed: Locations: Maximum Height: Maximum Length: Maximum Sign Area: Design and Colors: Single face non-illuminated pour-in-place concrete monument sign with individual dimensional letters. See page C2 One. Where indicated on Project Site Plan, page G2. 5'-0" from grade at the base of the sign. 20'-0". 2,867 Sq. Ft. (Letters Only). According to the project design and colors. C1

13 H PROJECT MONUMENT SIGN SPECIFICATIONS & DIMENSIONS 10" 1'-6" Color & Material Schedule 1'-7" 10" 10" 9" 1'-6" 1'-6" Plan View 20'-0" 10" x 15' -7 1/4 Sign Area = Sq. Ft. A. Reinforced pour-in-place concrete monument, exterior latex flat color to match Sherwin-Williams #SW 7067 Cityscape. B. 1" deep aluminum F. C. O. letters with a Matthews Brushed Aluminum acrylic polyurethane enamel finish. C. Pour-in-place concrete with a natural polished finish and clear satin protective coating. D. 5" x 2" x 1/4" aluminum rectangular tube fabricated bar with a Matthews Brushed Aluminum acrylic polyurethane enamel finish. E. Monument area with exterior latex flat paint to match Sherwin-Williams #SW 7066 Gray Matters. F. Monument area with exterior latex flat paint to match Sherwin-Williams #SW 7064 Passive. G. Monument area with exterior latex flat paint to match Sherwin-Williams #SW 7004 Snowbound. H. 3" x 2" x 1/4" aluminum rectangular tube fabricated supports with a Matthews Brushed Aluminum acrylic polyurethane enamel finish. I. 1" formed reveals painted to match the adjacent upper area color. 18'-6" A 2'-4" B 9" 4'-0" 1'-6" 17'-0" 1'-6" C 10" D E 5'-0" 4'-2" F I G Project Monument Sign Scale: 1/4" = 1'-0" End View C2

14 BUILDING ADDRESS SIGNS ALLOWABLE PARAMETERS Permitted Sign Type: Specifications: Quantity allowed: Locations: Maximum Dimensions: Design and Colors: Individual dimensional stainless steel numerals. See page D2 One on Building 5390 and two on Building Where indicated on Building Elevations, pages D3-D4 and on Project Site Plan, page G1 and G2. As indicated on Specifications and Dimensions, page D2. As specified on Specifications and Dimensions, page D2. D1

15 BUILDING ADDRESS SIGNS SPECIFICATIONS & DIMENSIONS A ual 51" 5 A. Color & Material Schedule 4" deep Brushed Stainless Steel fabricated numerals, hidden clip mounted to the building wall ual 40" 10" 40" 10" 40" 10" 40" 13" 51" 13" 51" 13" 51" ual ual 5390 Building Address Sign Scale: 1/16" = 1'-0" 5630 Building Address Signs Scale: 1/16" = 1'-0" D2

16 BUILDING ADDRESS SIGNS 5390 BUILDING ELEVATION Rickenbacker, East Elevation, North Corner Scale: 1" = 25'-0" D3

17 BUILDING ADDRESS SIGN 5630 BUILDING ELEVATIONS Rickenbacker, West Elevation Scale: 1" = 25'-0" Rickenbacker, North Elevation, East End Scale: 1" = 25'-0" D4

18 DEVELOPER DIMENSIONAL BUILDING SIGN ALLOWABLE PARAMETERS Permitted Sign Type: Specifications: Quantity allowed: Location: Maximum Height: Maximum Length: Maximum Sign Area: Design and Colors: Illuminated or Non-Illuminated stainless steel reverse channel dimensional background and symbol. See page E2 One per buildings 5390 & Where indicated on Allowable Location Elevations, page E3 and Project Site Plan, pages G1 and G2. 4'-0" 4'-0" 16 Square Feet. According to Property Owners/Develoers logo and colors. E1

19 DEVELOPER DIMENSIONAL BUILDING SIGN SPECIFICATIONS & DIMENSIONS A B 4'-0" 3'-0" C D New Developer Dimensinal Building Logo Scale: 3/4" = 1'-0" End View Color & Material Schedule A. B. C. D. 4" deep Brushed Stainless Steel fabricated back, hidden clip mounted to the building wall. 3" deep Stainless steel reverse channel logo piece with an Orange satin acrylic polyurethane enamel finish in two options: 1. Non-illuminated. 2. LED internal halo illumination. 3" deep Stainless steel reverse channel logo piece with a Dark Blue satin acrylic polyurethane enamel finish in two options as indicated above. Bolts through 3/4" stainless steel tube spacers. E2

20 DEVELOPER DIMENSIONAL BUILDING SIGN ALLOWABLE LOCATION ELEVATIONS 4' 5390 Rickenbacker, North Elevation, East End Scale: 1" = 25'-0" 4' 5630 Rickenbacker, North Elevation, East End Scale: 1" = 25'-0" E3

21 COMMEMORATIVE FREE STANDING SIGN ALLOWABLE PARAMETERS Permitted Sign Type: Specifications: Quantity allowed: Locations: Maximum Height: Maximum Length: Maximum Sign Area: Design and Colors: Ground mounted non-illuminated stainless steel plaque. See page F2 One per project, page G1. Where indicated on Project /site Plan, page G1. 5'-0" 3'-3" 4 Sq. Ft. Per design, see page F2. F1

22 COMMEMORATIVE FREE STANDING SIGN SPECIFICATIONS & DIMENSIONS A E B 5 1/2" 3.34" D C Plan View F 3'-3" A 5 1/2" 2" 2'-0" 2" 5 1/2" Color & Material Schedule 2'-0" Mexican-American population, was also In the early 1940's the temporary home one of two of many service men reservoirs, nicknamed the Sleepy involved in activities surrounding World Lagoon, existed upon themselves to issue vigilante justice behind the building by attacking the pachucos in a series of Angeles history, referred to as the Zoot Suit incidents called the Zoot Suit Riots. Riots. The riots began after a confrontation Local Mexican-American youth, many of whom belonged to neighborhood gangs clean up Main Street... referred to as Pachucos, often used the of pachuco gangs. On the following day, a convoy of sailors headed On the night of August 1, to East Los Angeles and 1942, members of the began clubbing Mexican- 38th Street gang allegedly American youth, beat and stabbed a stripping any found to be Mexican-American man wearing Zoot Suits. named Jose Gallardo Additional rioting and incidents against Diaz, after mistakenly Latinos continued for a time in San Diego; authorities, police and local newspapers was Oakland; Beaumont, TX; Chicago, IL; exaggerated, apparently due to racial populated by Mexicanprejudice. The L.A.P.D. quickly rounded up Americans and charges. A little frequented by their youth, over two years later became the home of the in October of 1944, Cheli Air Force Supply the trial was Base in Named determined to have after the World War II been held in naval hero and p o s t h u m o u s B A. 6" x 6" (nominal) rough sawn sealed redwood post, mounted in a concrete footing. B. 3/4" bolts through 1" round stainless steel tube spacers. C. 1/4" etched stainless steel plaque. D. 5 1/2" x 5 1/2" fabricated 1/2" Cor-Ten steel beam, mounted in a concrete footing. E..090 aluminum cover with a Matthews Brushed Aluminum acrylic polyurethane enamel finish. F. 3" x 3" x.125" aluminum square tube frame with a Matthews Brushed Aluminum acrylic polyurethane enamel finish. 5'-0" C 3'-0" D New Commemorative Free Standing Sign Scale: 1/2" = 1'-0" F2

23 5390 & 5391 SITE PLAN TYPICAL ALLOWABLE SIGN LOCATIONS 5391 Rickenbacker Road 710 Freeway 5390 & 5391 Rickenbacker Site Plan Scale: 1" = 150'-0" 5390 Key: Landmark Signs, Inc Allowable Corporate Wall Sign Locations. Bulding Address Sign (Page D1). Developer Building Sign (Page E1). Commemorative Sign (Page F1). G1

24 5630 SITE PLAN TYPICAL ALLOWABLE SIGN LOCATIONS Rickenbacker Road 5630 Sixth Street 5630 Rickenbacker Site Plan Scale: 1" = 150'-0" Key: Allowable Corporate Wall Sign Locations. Project Monument Sign (Page C1). Bulding Address Signs (Page D1). Developer Building Signs (Page E1). Landmark Signs, Inc G2