PORTAGE COUNTY WATER RESOURCES DRAFTING STANDARDS. Date: January 26, 2001

Size: px
Start display at page:

Download "PORTAGE COUNTY WATER RESOURCES DRAFTING STANDARDS. Date: January 26, 2001"

Transcription

1 PORTAGE COUNTY WATER RESOURCES DRAFTING STANDARDS Date: January 26, 2001

2 Portage County Water Resources Drafting Standards. AutoCad 2000/Land Development Desktop R2 Friday, January 26, 2001 Preface: Part 1 General Practices 1.01 Scales 1.02 Text Styles 1.03 Piping Conversions 1.04 Drawing Naming 1.05 Mark-ups 1.06 Basic Drawing Principles 1.07 Layering System 1.08 Hatching Part 2 Legend & Symbols 2.01 Pipe Legend 2.02 Pipe Fittings 2.03 General Plan Symbols 2.04 Plan and Profile Symbols 2.05 Miscellaneous Line Legend 2.06 Standard Title Sheet 2.07 Standard Frame Part 3 Dimensioning and Labeling 3.01 Basic Practices 3.02 Placement of Dimensions and Extensions Lines 3.03 Notes 3.04 Additional Info 3.05 Standard Abbreviations Part 4 Drafting Administration 4.01 Drawing Files 4.02 Plotting Procedures 4.03 Standard Detail Management 4.04 Special Notes Library 4.05 General Notes Library

3 PREFACE The purpose of a set of plans is to delineate the intended work with sufficient details of design, supplemented with specifications, in such a manner that they are clearly and uniformly interpreted by engineers and contractors. The drawing documents serve as a permanent record of the project and must provide sufficient data to enable the contractor to make an accurate bid and perform the work as intended. Clarity, completeness and conciseness are essential in avoiding misinterpretation. Unnecessary details should be avoided. Repetition of the specifications such as specifying capacities, etc., should also be avoided. The plans become part of the contract and represent the detailed description of the work which the contractor agrees to do in consideration for an agreed sum. It is important the designer, engineer or technician understand that errors, contradictions or omissions in the plans may result in expensive change orders at the time of construction. The importance of minimizing this situation cannot be over-emphasized. A general knowledge of drafting practices (as described in the American National Drafting Standards Manual ANSI Y-14) is required by the Technician. It is assumed that the technician has prior exposure to ANSI Y14 from previous employment or educational background. Part 1 GENERAL PRACTICES 1.01 SCALES Preliminary plans should be plotted on paper. Final plans shall be plotted on mylar. The following are recommended plotting scales. Do not proceed with an assumed scale without consulting with the project engineer. For treatment plant structures: 1/8 =1-0 for general plan views 1/4 or 3/8 =1-0 for plan views 1/4 =1-0 for whole or half sections through tanks and buildings 3/8, 1/2 or 3/4 =1-0 for enlarged sections and details For plan and profile sheets: 1 = 100 general plans 1 = 20 horizontal and 1 = 5 for congested areas such as city streets 1 = 50 horizontal and 1 = 5 for more open areas such as country roads 1.02 TEXT STYLES For process drawings: Existing style parameters:

4 Font = Simplex Height = Leroy #100 Width Factor = 0.8 Obliquing Angle = 15 degrees For Plan and Profile Sheets: Existing Style parameters: Font = Simplex Height = Leroy #100 Width Factor = 0.8 Obliquing Angle = 0 Proposed Style parameters: Font = Simplex Height = Leroy # 120 Width Factor = 1 Obliquing Angle = 0 When two (2) proposed utilities are shown on the same project (i.e., sanitary and waterline) the proposed text for the waterline should be differentiated from the sanitary with the use of a bolder color or text font such as Romand PIPING CONVERSIONS: For Process Drawings: For plot scales of 1/4, 3/8 or 1/2, process piping of 3 and smaller will be shown with a single line. Process piping of 4 and larger will be shown with double lines. These standards may be modified for plot scales of 1/8 and smaller. For Plan and Profile and/or Site Plan drawings: For plot scales of 1=20, 1=30 or 1=40 - Plan view utility piping smaller than 18-inch will be shown with a single line. Profile view utility piping 18-inch and larger with be shown with double lines. See Section 2C for appropriate line types. These standards may be modified for plot scales or 1=50 and smaller DRAWING NUMBERING The lead technician initiating work on a project is responsible for creating and distributing the title block information to all other technicians who will be involved on the project. The lead technician shall create a drawing of the title block area from the standard title block drawing.

5 The drawing shall be named as indicated below: Applies to regular AutoCad drawings: U:\ACADDATA\STD\..for Standard Drawings U:\ACADDATA\MISC\ for Miscellaneous Drawings U:\ACADDATA\SEWER\ for Sewer Projects created w/o Land Development U:\ACADDATA\WATER\ for Water drawings created w/o Land Development For Land Development Desktop Project files: U:\ACADDATA\LAND PROJ R2\PROJECT NAME\DWG\.. The above PROJECT NAME shall be described with the official project name, obtainable from the Official Project List maintained by the Division Manager, but not limited by a precise number of characters; be concise with the project name. Then the name of the drawing shall be descriptive of the drawing itself, (i.e. planprof will suffice for plan and profile drawings, etc.). It is the discretion of the drafter to name the drawing with the best, short descriptive name for the drawing. Land Development Desktop projects share a common database from within the current project folder. Thus, all the drawings that pertain to that project shall be saved under the same project folder in the DWG folder MARK-UPS When marking up a print for corrections or additions the following colors should be used. Red - for things that are to be removed. Red - for additions or corrections that are to be made. Yellow to indicate work that has been addressed. Pencil for drafting information only (i.e. sizes, dimensions or instructions not to be placed on the drawings) BASIC DRAWING PRINCIPLES There are some basic principles to be followed for the preparation of functional design drawings: Avoid artistry do not indulge in representation to a point where it will border on artistry. Avoid repetition drawings should avoid showing repetitive dimensions. (See also Part 4 Dimensioning and Labeling )

6 meaning intended. Do Use simplicity keep drawing so that they are clear and simple, but still convey the not show unnecessary detailing on equipment. In most cases an outline representation of equipment is adequate LAYERING SYSTEM: CURRENTLY BEING UPDATED. As a rule, use the following system for layering: Additional layers may be added or required to be more specific to the drawing. These are not limited to, but should consist of the above pattern of naming. It is still the drafter s best discretion to determine the exact layer names used in the drawing. See Figure HATCH PATTTERNS AutoCAD s hatch patterns are to be used to show certain types of materials used in construction. Consistency is to be used between drawings. A number of standard hatch patterns are stored in Land Development Desktop Library and can be used readily. A nonstandard hatch pattern is not transportable unless the appropriate.pat file is sent with the drawing file. Part II. Legends and Symbols 2.01 PIPE LEGEND The following standard legends are to be used on all construction drawings. The legends, with the exception of plan and profile sheets, are intended so as to avoid notation of each item. See Figure 2.01 (below)

7 Figure 2.01

8 2.02 PIPE FITTINGS Pipe fittings may be inserted from the standard pipe fittings drawing located in the Standards folder on the network drive GENERAL PLAN SYMBOLS Plan and profile line legends shall adhere to the following figure. Figure 2.03

9 Figure 2.03 continued

10 Figure 2.03 continued

11 2.04 PLAN AND PROFILE SYMBOLS Figure 2.04

12 Figure 2.04 continued

13 2.05MISCELLANEOUS LINE LEGEND Figure 2.05

14 2.06 STANDARD TITLE SHEET The standard prototype Portage County Water Resources Title sheet can be found on the server in the Standard folder and with the name of STDTITLE.DWG. In some cases the text may need to be changed to accommodate more lines of text, drawing lists, quantities and approvals. Do not change the grouping of the information without consulting the Project Engineer. Any other modifications should be kept to a minimum. The project location map should be inserted at the specified scale. See Figure STANDARD BORDER FRAME The standard border frame is drawn at 1=1 and saved in the Standard folder on U:\ When inserting into a drawing, use the intended scale of the drawing scale. See Figure 2.07 Part III Dimensioning and Labeling 3.01 BASIC PRACTICES The following check list summarizes some common dimensioning conventions used to reduce mistakes. Each dimension should be given clearly, so that it can be interpreted in only one way. Dimensions should not be duplicated or information given two different ways. No dimensions shall be given except those that are needed for construction or estimated quantities. Dimensions should be given between centerlines or wall surfaces that have a functional relation to each other or that control the location of openings or access ways. Dimensions should be given so that it will not be necessary for the contractor to calculate, scale or assume any dimensions. Dimensions should be attached to the view where the shape is best shown. Avoid dimensioning to hidden lines. Dimensions should not be placed upon a view unless shown with clarity and long extension lines are avoided. Dimensions applying to two adjacent views should be placed between views, unless clearness is promoted by placing some of them outside.

15 The longer dimensions should be placed outside all intermediate dimensions so that dimension lines will not cross extension lines PLACEMENT OF DIMENSIONS AND EXTENSION LINES The correct placement of dimension lines and extensions is crucial to the legibility of the drawing. Shorter dimensions should be closest to the object while longer dimensions shall be placed outside and beyond the shorter dimensions. The crossing of extension lines shall be avoided this way. Extension lines shall never form a continuation of any line of the drawing to avoid confusion. Hidden lines should never be dimensioned unless no other view is available to show that dimension NOTES Some dimensions may need to be supplemented with notes. They should be brief and carefully worded to be capable of one interpretation. Notes should be lettered horizontally on the sheet and arranged in a systematic manner. They should not be lettered in crowded places. Avoid placement of notes between views where possible. The notes should be placed next to the correct view where application is needed so as to not confuse the reader. Leaders should not cross intersections, specific points or corners of objects in the drawing and cross as few lines as possible. Notes are classified as general notes that apply to the entire drawing. Local notes are notes the apply to specific items. General notes should be lettered in the lower right-hand corner of the drawings, above or to the left of the title block, or in a central position below the view to which they apply ADDITIONAL INFO The main purpose of a plan view is to show equipment and piping relative to architectural space requirements. Equipment and piping layout in plan view should be dimensioned from inside face of walls to important centerlines such as discharge and suction piping or centers of pump pads. In addition to pipe material, size and flow direction should also be indicated in both plan and section views. (ie., 6 DIP blower pump discharge). Titles for plan views are to be labeled with reference to the elevation from which the plan is viewed and not the floor elevation. A plan cut five feet above a floor having an elevation of would be labeled EL The cutting plane arrows used on architectural, process, structural, plumbing, HVAC and electrical plan views are shown here:

16 Figure 3.04 The corresponding sectional view is to be labeled as follows with the appropriate scale: Please note the left justification of the scale. Cutting plane arrows can be selected from the symbols library STANDARD ABBREVIATIONS See the attached Figure 3.05 standard abbreviations for commonly used standard abbreviations that may be used on the drawings at any time. Part IV Drafting Administration 4.01 DRAWING FILES Drawing files are stored on the Network server. The location is as follows: U:\ACADDATA\SEWER\Project Name\DWG Name (for sewer drawings done without Land Development Desktop). The drafter puts the project name and drawing name on the drawing.

17 U:\ACADDATA\WATER\Project Name\DWG Name (for water drawings done without Land Development Desktop) U:\ACADDATA\LANDPROJ R2\Project Name\DWG\DWG Name (for drawings done with Land Development Desktop) Note: Any drawings not saved on Network Drive U:\ will not be backed up by the server tape backup. When saving a drawing and choosing a drawing name, a folder shall be created with the project name and the drawing shall be saved with a descriptive name into the respective project folder. Drawings received on disk by surveyors and or consultants are to be copied onto the server under their respective project folder and the disk(s) shall be logged in to the data received log book PLOTTING PROCEEDURES Drawings are plotted on paper and official title sheets for signatures are plotted on mylar. As-builted drawings are plotted to mylar and stored in the hanging file STANDARD DETAIL MANAGEMENT Water Resources Standard drawings are saved on the network drive on u:\acaddata\standard\ and are not to be altered or changed unless requested by the construction engineer or the engineering department itself. These drawings consist of standard water and sewer construction details, a title sheet, pump station drawings and miscellaneous drawings. Changes are submitted to the Engineering Division Manager for final approval. Drawings are drawn at a scale of 1=1 and then plotted at the matching dimscale or the intended plot scale SPECIAL NOTES LIBRARY Special notes are drawn at a scale of 1=1 and saved in the U:\Acaddata\Standard folder. They may be accessed and inserted into a drawing at the intended scale of the drawing GENERAL NOTES LIBRARY General notes are drawn at a scale of 1=1 and saved in the U:\Acaddata\Standard foler. These may be accessed and inserted into a drawing at the intended scale of the drawing. T:\DATA\JGE\My Documents\PCWR DraftStds.doc

CONSULTANT: Wantman Group, Inc SERVICE AUTHORIZATION NO. _12-03 FOR CONSULTING SERVICES CITY PROJECT NO CONSULTANT PROJECT NO.

CONSULTANT: Wantman Group, Inc SERVICE AUTHORIZATION NO. _12-03 FOR CONSULTING SERVICES CITY PROJECT NO CONSULTANT PROJECT NO. EXHIBIT A CONSULTING SERVICE AUTHORIZATION DATE: CONSULTANT: Wantman Group, Inc SERVICE AUTHORIZATION NO. _12-03 FOR CONSULTING SERVICES CITY P.O. NO. CITY EXPENSE CODE CITY PROJECT NO. 14-073 CONSULTANT

More information

Miami University. Physical Facilities Department. CAD Standards. April 2004

Miami University. Physical Facilities Department. CAD Standards. April 2004 Miami University Physical Facilities Department CAD Standards April 2004 1.0.0 OVERVIEW These standards pertain to the use, production and submittal of electronic CAD files at Miami University. They have

More information

Fundamentals for building Drawing

Fundamentals for building Drawing Fundamentals for building Drawing What is Drawing Introduction Knowledge of preparing and understanding drawing will prove to be an invaluable aid while performing their jobs effectively, efficiently.

More information

Project Booklet. Structural Drafting with AutoCAD

Project Booklet. Structural Drafting with AutoCAD Project Booklet Structural Drafting with AutoCAD Introduction 1 General Setup 2 Border and Title Block 3 Drafting the Foundation Plan (Plate 1) 8 Drafting the South Elevation (Plate 2) 11 Drafting Section

More information

DIGITAL DATA SUBMISSION STANDARDS Procedures and Guidelines

DIGITAL DATA SUBMISSION STANDARDS Procedures and Guidelines DIGITAL DATA SUBMISSION STANDARDS Procedures and Guidelines 2014 Citizens Wastewater of Westfield - GIS Digital Standards Table of Contents Introduction... 3 Definitions and Terms... 3 Reference Documents...

More information

Elementary Dimensioning

Elementary Dimensioning Elementary Dimensioning Standards Institutions ANSI - American National Standards Institute - creates the engineering standards for North America. ISO - International Organization for Standardization -

More information

1.0 INTRODUCTION DEFINITIONS DRAWING CONTROL PREPARATION OF SPECIFICATIONS AND DATASHEETS... 5

1.0 INTRODUCTION DEFINITIONS DRAWING CONTROL PREPARATION OF SPECIFICATIONS AND DATASHEETS... 5 TABLE OF CONTENTS 1.0 INTRODUCTION... 3 2.0 DEFINITIONS... 4 3.0 DRAWING CONTROL... 4 4.0 PREPARATION OF SPECIFICATIONS AND DATASHEETS... 5 5.0 GUIDELINES FOR PREPARATION OF DRAWINGS... 5 6.0 CONTENTS

More information

Chapter 23. Signing and Pavement Marking Plans

Chapter 23. Signing and Pavement Marking Plans Chapter 23 Signing and Pavement Marking Plans 23.1 General... 23-3 23.2 Key Sheet... 23-4 23.3 Signature Sheet... 23-4 23.4 Tabulation of Quantities and Pay Item Notes... 23-4 23.4.1 Standard Notes...

More information

SECTION III SUBMITTALS AND APPROVALS

SECTION III SUBMITTALS AND APPROVALS SECTION III SUBMITTALS AND APPROVALS In order to expedite the approval process of new water distribution system and sanitary sewer collection system extensions, the Hilton Head No. 1 Public Service District

More information

Making an Architectural Drawing Template

Making an Architectural Drawing Template C h a p t e r 8 Addendum: Architectural Making an Architectural Drawing Template In this chapter, you will learn the following to World Class standards:! Starting from Scratch for the Last time! Creating

More information

CHAPTER A-10 DRAWINGS

CHAPTER A-10 DRAWINGS CHAPTER A-10 DRAWINGS INDEX Revised May 2018 10.1 GENERAL 10.1.1 Purpose and Scope 10.2 APPLICABLE PUBLICATIONS 10.3 COMPUTER AIDED DESIGN (CAD) 10.3.1 CAD Requirements 10.3.2 CAD Deliverables 10.3.3 CAD

More information

Plan Submittal and Review Checklist

Plan Submittal and Review Checklist Improving quality of life today creating a better tomorrow Plan Submittal and Review Checklist Version 1.2 September 4, 2017 Contents Overview... 2 Plan Submittal Checklist... 2 Plan Review Checklist -

More information

Scale and Dimensioning (Architectural Board Drafting)

Scale and Dimensioning (Architectural Board Drafting) Youth Explore Trades Skills Description In this activity, the teacher will first select an object that is larger than the page and scale it to fit in the designated drawing area to explain architectural

More information

Technical English -I 4 th week ENGINEERING DRAWING

Technical English -I 4 th week ENGINEERING DRAWING Technical English -I 4 th week ENGINEERING DRAWING What is engineering drawing? It is the art of representation of geometrical objects on a drawing sheet. An engineering drawing is used to fully and clearly

More information

UDS OVERVIEW Uniform Drawing System

UDS OVERVIEW Uniform Drawing System UDS OVERVIEW Uniform Drawing System The Construction Specifications Institute 601 Madison Street Alexandria, VA 1994 CSI began development of UDS Organization and presentation of drawing sets Organization

More information

DFTG-1305 Technical Drafting Prof. Francis Ha

DFTG-1305 Technical Drafting Prof. Francis Ha DFTG-1305 Technical Drafting Prof. Francis Ha Session 5 Dimensioning Geisecke s textbook: 14 th Ed. Chapter 10 p. 362 15 th Ed. Chapter 11 p. 502 Update: 17-0508 Dimensioning Part 1 of 2 Dimensioning Summary

More information

APPENDIX D: DRAWING SUBMISSION STANDARDS

APPENDIX D: DRAWING SUBMISSION STANDARDS 1.0 FIRST SUBMISSION CONCEPTUAL DESIGN Once the Developer has obtained approval for a Development Application where Park or Open Space improvements are required, a detailed Park or Open Space submission

More information

Orthographic Drawing (Architectural Board Drafting)

Orthographic Drawing (Architectural Board Drafting) Design and Drafting Description In this activity, the teacher will introduce orthographic projection, in which a multi-view drawing shows how the sides of an object are related to each another. Students

More information

Minimum Drawing & Electronic Submittal Requirements For Record Drawings /As-Builts

Minimum Drawing & Electronic Submittal Requirements For Record Drawings /As-Builts Minimum Drawing & Electronic Submittal Requirements For Record Drawings /As-Builts PUBLIC WORKS ENGINEERING DEPARTMENT Revised: February 1, 2017 MINIMUM DRAWING REQUIREMENTS A. GENERAL PLAN REQUIREMENTS:

More information

Drawing Standards & Conventions for IDD

Drawing Standards & Conventions for IDD Drawing Standards & Conventions for IDD This document consists of a set of standards that have been developed to maintain a consistency in Interior Decoration and Design students work. The standards are

More information

CITY OF LA MARQUE CHAPTER GRAPHIC REQUIREMENTS CONSTRUCTION PLAN AND MISCELLANEOUS REQUIREMENTS

CITY OF LA MARQUE CHAPTER GRAPHIC REQUIREMENTS CONSTRUCTION PLAN AND MISCELLANEOUS REQUIREMENTS CITY OF LA MARQUE CHAPTER 2 -------------------------------------------- GRAPHIC REQUIREMENTS CONSTRUCTION PLAN AND MISCELLANEOUS REQUIREMENTS CHAPTER 2 ------------------------------------------------

More information

PMA ONLINE TRAINING. Commercial Drawings. One Hour Continuing Education

PMA ONLINE TRAINING. Commercial Drawings. One Hour Continuing Education PMA ONLINE TRAINING Commercial Drawings One Hour Continuing Education PMA training disclaimer The information provided in this document is intended for use as a guideline and is not intended as, nor does

More information

AutoCAD Standards University of California, Santa Cruz Physical Planning & Construction

AutoCAD Standards University of California, Santa Cruz Physical Planning & Construction University of California, Santa Cruz Physical Planning & Construction 1. General Requirements: 1.1 Format 1.2 Ownership 2. Required Data: 2.1 Area Tabulation 2.2 Drawing Files 2.3 External References 2.4

More information

BASIC CADD DRAWING PROCEDURES

BASIC CADD DRAWING PROCEDURES BASIC CADD DRAWING PROCEDURES I. Set up Electronic Drawing Environment: 1) SET UNITS 2) DETERMINE ELECTRONIC SCALE FACTOR (SF) a. CALCULATE WHITE SPACE 3) SET LIMITS (MODEL SPACE) 4) ZOOM ALL, F7 (TURN

More information

STATE UNIVERSITY CONSTRUCTION FUND

STATE UNIVERSITY CONSTRUCTION FUND DIRECTIVE 1C-12 Issue date: August 2012 1. General SURVEY, MAPPING AND UTILITY LOCATING This Directive has been developed as a general guide for the survey and mapping effort required for Fund projects.

More information

CITY OF BEVERLY HILLS Department of Public Works and Transportation Civil Engineering Division SANITARY SEWER IMPROVEMENT PLAN REVIEW CHECKLIST

CITY OF BEVERLY HILLS Department of Public Works and Transportation Civil Engineering Division SANITARY SEWER IMPROVEMENT PLAN REVIEW CHECKLIST CITY OF BEVERLY HILLS Department of Public Works and Transportation Civil ing Division SANITARY SEWER IMPROVEMENT PLAN REVIEW CHECKLIST The following checklist consists of the minimum requirements for

More information

PLANNING AND DEVELOPMENT

PLANNING AND DEVELOPMENT OVERVIEW Effective January 1, 1992 all applications for multi-family residential and all non-residential building permits require site plan approval before permit issuance. All new developments and existing

More information

UTILITY AND STREET CONSTRUCTION PLAN REQUIREMENTS SECTION 1

UTILITY AND STREET CONSTRUCTION PLAN REQUIREMENTS SECTION 1 UTILITY AND STREET CONSTRUCTION PLAN REQUIREMENTS SECTION 1 ENGINEERING STANDARDS FOR UTILITY AND STREET CONSTRUCTION PLANS MARCH 2014 CONSTRUCTION PLAN SHEET FORMAT REQUIREMENTS REPRODUCIBLE MYLAR 1.

More information

1. Land survey Work. 2. Civil and Structural engineering services.

1. Land survey Work. 2. Civil and Structural engineering services. SECTION 01050 FIELD ENGINEERING PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division-1 Specification

More information

Bureau of Engineering. CADD Standards. Preface

Bureau of Engineering. CADD Standards. Preface BOE CADD STANDARDS Preface The is committed to improving the quality of project delivery offered to all our Clients. By producing electronic design data consistently, communication among designer, owner

More information

LESSON 1: UNDERSTANDING CONSTRUCTION DRAWINGS

LESSON 1: UNDERSTANDING CONSTRUCTION DRAWINGS LESSON 1: UNDERSTANDING CONSTRUCTION DRAWINGS INTRODUCTION In this lesson, you ll learn about the different types of drawings used in the construction industry, and how to read floor plans, section drawings,

More information

PRELIMINARY PLAT CHECK LIST

PRELIMINARY PLAT CHECK LIST Name of Proposed Subdivision: The following items must be included with the initial submittal of a Preliminary Plat: Application, filled out completely Project Narrative Pre-application Conference Report

More information

Chapter 2: Dimensioning Basic Topics Advanced Topics Exercises

Chapter 2: Dimensioning Basic Topics Advanced Topics Exercises Chapter 2: Dimensioning Basic Topics Advanced Topics Exercises Dimensioning: Basic Topics Summary 2-1) Detailed Drawings 2-2) Learning to Dimension 2-3) Dimension Appearance and Techniques. 2-4) Dimensioning

More information

SECTION SUBMITTALS. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.

SECTION SUBMITTALS. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. SECTION 013300 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting

More information

PLAN PREPARATION (G 700)

PLAN PREPARATION (G 700) TABLE OF CONTENTS PLAN PREPARATION (G 700) SECTION NO. SUBJECT DATE G 710 STANDARDS June, 1968 G 711 Format G 712 Drawing Orientation June, 1968 G 713 Drafting Standards " G 713.1 Scales G 713.2 Line Convention

More information

Chapter 8. Piping Isometrics

Chapter 8. Piping Isometrics Chapter 8 Piping Isometrics An isometric drawing is a type of pictorial drawing in which three sides of an object can be seen in one view. It s popular within the process piping industry because it can

More information

Update: July 20, 2012

Update: July 20, 2012 Location and Design Manual, Volume 3 ODOT Office of CADD and Mapping Services Update: July 20, 2012 ** NOTE: All metric references have been removed from this manual. ** PREFACE REVISIONS Glossary of Terms

More information

8.1 Control. 8.2 Sheet Setup

8.1 Control. 8.2 Sheet Setup 8.1 Control Responsibility for development of the pipe data sheets is in the hands of the project s drainage or roadway designer. Pipe data sheets should be developed after the drainage design is fairly

More information

SANITARY SEWER SYSTEM ADMINISTRATIVE STANDARDS A.1 SANITARY SEWER SYSTEM PLAN SUBMITTAL PROCEDURES AND GENERAL REQUIREMENTS

SANITARY SEWER SYSTEM ADMINISTRATIVE STANDARDS A.1 SANITARY SEWER SYSTEM PLAN SUBMITTAL PROCEDURES AND GENERAL REQUIREMENTS SANITARY SEWER SYSTEM ADMINISTRATIVE STANDARDS A.1 SANITARY SEWER SYSTEM PLAN SUBMITTAL PROCEDURES AND GENERAL REQUIREMENTS All plans for sanitary sewer main extensions, improvements and modifications

More information

READING ARCHITECTURAL PLANS

READING ARCHITECTURAL PLANS READING ARCHITECTURAL PLANS ARCHITECTURAL DRAWINGS FOR A HOUSE Architectural drawings contain information about the size, shape, and location of all parts of the house ARCHITECTURAL DRAWINGS FOR A HOUSE

More information

PART XII: TOPOGRAPHIC SURVEYS

PART XII: TOPOGRAPHIC SURVEYS PART XII: TOPOGRAPHIC SURVEYS 12.1 Purpose and Scope The purpose of performing topographic surveys is to map a site for the depiction of man-made and natural features that are on, above, or below the surface

More information

1.1 GENERAL RECORD DRAWING REQUIREMENTS

1.1 GENERAL RECORD DRAWING REQUIREMENTS Page 1 of 5 VILLAGE OF ROMEOVILLE RECORD DRAWINGS CHECKLIST PART I GENERAL Record drawings are required to provide a means of schematic verification that the intent of the approved engineering design has

More information

Technological Design Mr. Wadowski. Orthographic & Isometric Drawing Lesson

Technological Design Mr. Wadowski. Orthographic & Isometric Drawing Lesson Technological Design Mr. Wadowski Orthographic & Isometric Drawing Lesson TOPICS Working Drawings, Isometric Drawings & Orthographic Drawings Glass box concept Multiview projection Orthographic projection

More information

SECTION 1 - GENERAL REQUIREMENTS

SECTION 1 - GENERAL REQUIREMENTS SECTION 1 - GENERAL REQUIREMENTS 1.1 GENERAL All plans must be provided to Alberta Transportation (AT) in hardcopy and digital formats. Beginning with the 2003 Highway and Bridge tender submissions, all

More information

ENGINEERING GRAPHICS ESSENTIALS. (A Text and Lecture Aid) Second Edition. Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS

ENGINEERING GRAPHICS ESSENTIALS. (A Text and Lecture Aid) Second Edition. Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS ENGINEERING GRAPHICS ESSENTIALS (A Text and Lecture Aid) Second Edition Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com

More information

11.0 INSTRUMENTATION LOOP DIAGRAMS

11.0 INSTRUMENTATION LOOP DIAGRAMS 11.0 INSTRUMENTATION LOOP DIAGRAMS Table of Contents 11.0 INSTRUMENTATION LOOP DIAGRAMS... 11-1 11.1 HISTORY OF CHANGE... 11-2 11.2 INSTRUMENT LOOP DIAGRAMS (ILD)... 11-4 11.2.1 Drawing Content... 11-4

More information

CHAPTER 3 INFORMATION REQUIRED FOR PUBLIC IMPROVEMENT CONSTRUCTION PLANS TABLE OF CONTENTS

CHAPTER 3 INFORMATION REQUIRED FOR PUBLIC IMPROVEMENT CONSTRUCTION PLANS TABLE OF CONTENTS CHAPTER 3 INFORMATION REQUIRED FOR PUBLIC IMPROVEMENT CONSTRUCTION PLANS TABLE OF CONTENTS Section Title Page 3.1 General... 3-1 3.1.1 Plan Set...3-1 A. Loveland (City Limits Only)...3-1 3.1.2 Final Mylars...3-1

More information

List of Figures. List of Forms

List of Figures. List of Forms City of Columbia Engineering Regulations PART 1: SUBMISSION OF PLANS Table of Contents Paragraph Description Page No. 1.1 General 1-1 1.2 Engineer s Report 1-1 1.3 Plans 1-3 1.4 Revisions to Approved Plan

More information

This specification describes the minimum technical requirements for drawings, as applicable to all disciplines.

This specification describes the minimum technical requirements for drawings, as applicable to all disciplines. SPEC-0800 1/5 1.0 PURPOSE This specification describes the minimum technical requirements for drawings, as applicable to all disciplines. 2.0 VALE DRAWING TYPE DEFINITIONS Engineering Drawings Engineering

More information

Required Supporting Information and Documentation for Historic Preservation Certification Applications

Required Supporting Information and Documentation for Historic Preservation Certification Applications Required Supporting Information and Documentation for Historic Preservation Certification Applications Part 1 Submittal- Evaluation of Significance Descriptive Information Describe the major features of

More information

Stanford University-Facilities Design Guideline SECTION Plans Review Submission Guidelines

Stanford University-Facilities Design Guideline SECTION Plans Review Submission Guidelines SECTION 01 33 00 Plans Review Submission Guidelines PART 1 GENERAL 1.01 OVERVIEW A. University Plans Review Process: 1. The process by which the Designer s schematic, design development, construction documents

More information

BRASELTON WATER AND WASTEWATER DEPARTMENT CONSTRUCTION PLAN REVIEW CHECKLIST May 2006

BRASELTON WATER AND WASTEWATER DEPARTMENT CONSTRUCTION PLAN REVIEW CHECKLIST May 2006 Project Name: BRASELTON WATER AND WASTEWATER DEPARTMENT CONSTRUCTION PLAN REVIEW CHECKLIST May 2006 Phase: Unit: # Lots: Development Type (residential, commercial, industrial, etc.) Braselton Project No.

More information

ID 40 Residential Design. General Notes Title Sheet and Index Cross-reference Symbols

ID 40 Residential Design. General Notes Title Sheet and Index Cross-reference Symbols ID 40 Residential Design General Notes Title Sheet and Index Cross-reference Symbols Title Sheet All plan sets include a Title sheet. It usually features a site plan, a drawing index, and the name of the

More information

UNIVERSITY OF ROCHESTER DESIGN STANDARDS FEBRUARY 29, 2012

UNIVERSITY OF ROCHESTER DESIGN STANDARDS FEBRUARY 29, 2012 SECTION 01950 - RECORD DRAWINGS & SPACE FLOOR PLANS 1.1 RECORD DRAWINGS MATERIAL AND FORMAT A. Definition 1. Final record drawings, or as-builts, are drawings, which are revised to reflect the changes

More information

MINIMUM DRAWING REQUIREMENTS FOR WATER AND SEWER LINE PROJECTS

MINIMUM DRAWING REQUIREMENTS FOR WATER AND SEWER LINE PROJECTS Public Works Department Water & Wastewater Services WATER & WASTEWATER ENGINEERING DIVISION 2555 West Copans Road Pompano Beach, Florida 33369 954-831-0745 FAX 954-831-0798/0925 MINIMUM DRAWING REQUIREMENTS

More information

B.2 MAJOR SUBDIVISION PRELIMINARY PLAN CHECKLIST

B.2 MAJOR SUBDIVISION PRELIMINARY PLAN CHECKLIST B.2 MAJOR SUBDIVISION PRELIMINARY PLAN CHECKLIST YES* GENERAL SUBMISSION ITEMS Does the submission include: 1. Thirteen (13) copies of completed Application Form? 2. Thirteen (13) copies of the Preliminary

More information

CITY OF LOMPOC DEVELOPMENT ASSISTANCE BROCHURE ENCROACHMENT PERMITS AND PUBLIC IMPROVEMENT PLANS

CITY OF LOMPOC DEVELOPMENT ASSISTANCE BROCHURE ENCROACHMENT PERMITS AND PUBLIC IMPROVEMENT PLANS CITY OF LOMPOC DEVELOPMENT ASSISTANCE BROCHURE E-10 ENCROACHMENT PERMITS AND PUBLIC IMPROVEMENT PLANS The City of Lompoc has determined that the Engineering Division should administer and issue Encroachment

More information

General Requirements for the Preparation of Plans

General Requirements for the Preparation of Plans August 6, 2003 General Requirements for the Preparation of Plans NOTE: This document is a Controller of Surveys Policy manual to be used as a general guideline for the preparation and examination of plans.

More information

5.7 Plan Documentation and Supporting Information.

5.7 Plan Documentation and Supporting Information. 5.7 and Supporting Information. In any case where the and Supporting Information for a Development Plan requires the submission of a Site Plan, Overall Plan, Landscape Plan, Building Elevations, Sign Plan

More information

SECTION 100 PRELIMINARY CONSIDERATIONS & INSTRUCTIONS

SECTION 100 PRELIMINARY CONSIDERATIONS & INSTRUCTIONS SECTION 100 PRELIMINARY CONSIDERATIONS & INSTRUCTIONS 101 General 102 Submittal Requirements A. Initial Submittal B. Second Submittal 103 Plan Requirements A. Subdivisions B. Site Plans 104 Approval of

More information

Section E NSPS MODEL STANDARDS FOR TOPOGRAPHIC SURVEYS Approved 3/12/02

Section E NSPS MODEL STANDARDS FOR TOPOGRAPHIC SURVEYS Approved 3/12/02 Section E NSPS MODEL STANDARDS FOR TOPOGRAPHIC SURVEYS Approved 3/12/02 1. INTRODUCTION This standard is written to provide the professional surveyor (Surveyor) and the client with a guideline for producing

More information

CITY OF MUSKEGO DRAFTING STANDARDS

CITY OF MUSKEGO DRAFTING STANDARDS CITY OF MUSKEGO DRAFTING STANDARDS GENERAL - These standards apply to all plans. 1. Plans must be prepared on sheets measuring 36 inch across and 22 inch to 24 inch high unless otherwise specified under

More information

Dimensioning. Dimensions: Are required on detail drawings. Provide the shape, size and location description: ASME Dimensioning Standards

Dimensioning. Dimensions: Are required on detail drawings. Provide the shape, size and location description: ASME Dimensioning Standards Dimensioning Dimensions: Are required on detail drawings. Provide the shape, size and location description: - Size dimensions - Location dimensions - Notes Local notes (specific notes) General notes ASME

More information

CHAPTER REQUIREMENTS FOR PLATS AND SITE PLANS

CHAPTER REQUIREMENTS FOR PLATS AND SITE PLANS CITY OF MOSES LAKE MUNICIPAL CODE CHAPTER 17.15 REQUIREMENTS FOR PLATS AND SITE PLANS Sections: 17.15.010 Purpose 17.15.020 General Requirements 17.15.030 Specific Plat Requirements 17.15.040 Specific

More information

CHAPTER 11 SURVEY CADD

CHAPTER 11 SURVEY CADD CHAPTER 11 SURVEY CADD Chapter Contents Sec. 11.01 Sec. 11.02 Sec. 11.03 Sec. 11.04 Sec. 11.05 Sec. 11.06 Sec. 11.07 Sec. 11.08 Sec. 11.09 Sec. 11.10 General Description of Survey File Contents of Survey

More information

Anne Arundel County Dept. of Inspections and Permits Water Sewer Plan Checklist

Anne Arundel County Dept. of Inspections and Permits Water Sewer Plan Checklist Project Name Project Number Engineer Plans are to be designed based on the standards set forth in the Anne Arundel County Design Manual Standards and Specifications, and all other manuals as stipulated

More information

Issue Date: August 2018 Revision: 03

Issue Date: August 2018 Revision: 03 ENGINEERING CADD MANUAL Issue Date: August 2018 Revision: 03 Developed For: Metra Engineering Department 547 West Jackson Blvd. Chicago, Illinois 60661 Developed By: Chandra Mahalingam CADD System Administrator

More information

Copyrighted Material. Copyrighted Material. Copyrighted. Copyrighted. Material

Copyrighted Material. Copyrighted Material. Copyrighted. Copyrighted. Material Engineering Graphics ORTHOGRAPHIC PROJECTION People who work with drawings develop the ability to look at lines on paper or on a computer screen and "see" the shapes of the objects the lines represent.

More information

Contents. Notes on the use of this publication

Contents. Notes on the use of this publication Contents Preface xxiii Scope Notes on the use of this publication xxv xxvi 1 Layout of drawings 1 1.1 General 1 1.2 Drawing sheets 1 1.3 Title block 2 1.4 Borders and frames 2 1.5 Drawing formats 2 1.6

More information

.1 Applicability: These criteria shall be applied as follows:

.1 Applicability: These criteria shall be applied as follows: DESIGN CRITERIA DIVISION 4800 STREET LIGHTING 4801 GENERAL: These criteria shall be adhered to for the design of all publiclyfinanced or privately-financed traffic signal systems to be installed in the

More information

GUIDELINES FOR DRAFTING

GUIDELINES FOR DRAFTING UNIT 1 GUIDELINES FOR DRAFTING 1.1 Introduction The term draughting is used to describe the language of drafting in this book. It defines the terminology, symbology, conventions, and standards used in

More information

SECTION 3 IMPROVEMENT PLAN REQUIREMENTS

SECTION 3 IMPROVEMENT PLAN REQUIREMENTS SECTION 3 IMPROVEMENT PLAN REQUIREMENTS CONTENTS Page 3-1 Digital Submittals 3-2 3-2 Paper Size and Scale 3-2 3-3 Drafting Standard 3-2 3-4 Title Sheet 3-2 3-5 Title Block 3-3 3-6 Drainage, Sewer, Water,

More information

SECTION 2 GENERAL REQUIREMENTS

SECTION 2 GENERAL REQUIREMENTS SECTION 2 GENERAL REQUIREMENTS 2-1 ENGINEER REQUIRED: All plans and specifications for Improvements which are to be accepted for maintenance by the County and private, on-site drainage and grading shall

More information

NEORSD. Cad Standards and Procedures Manual

NEORSD. Cad Standards and Procedures Manual NEORSD Cad Standards and Procedures Manual This Manual is being provided to you on loan from the NEOSRD and is the property of the NEOSRD. Periodic updates will be provided and you are responsible for

More information

Subdivision Application Checklist

Subdivision Application Checklist City of Portsmouth, New Hampshire Subdivision Application Checklist This subdivision application checklist is a tool designed to assist the applicant in the planning process and for preparing the application

More information

RIT CAD Specifications

RIT CAD Specifications RIT CAD Specifications The design team shall provide RIT with Revit, AutoCAD, and PDF files that capture the construction conditions of the associated project. This document outlines requirements for submitting

More information

Washington County Road Engineering Plan Submittal/Review Checklist

Washington County Road Engineering Plan Submittal/Review Checklist Washington County Road Engineering Plan Submittal/Review Checklist Washington County Land Use Case File Number: Parcel(s): Developer/Owner Name(s): Developer/Owner E-mail(s): The following elements should

More information

ENGINEERING DRAWING LECTURE 4

ENGINEERING DRAWING LECTURE 4 ENGINEERING DRAWING LECTURE 4 Conventions Convention or Code: The representation of any matter by some sign or mark on the drawing is known as convention or code. The convention make the drawing simple

More information

Section 4-02 Typical Sections TABLE OF CONTENTS. INTRODUCTION...2 General...2

Section 4-02 Typical Sections TABLE OF CONTENTS. INTRODUCTION...2 General...2 Section 4-02 Typical Sections TABLE OF CONTENTS INTRODUCTION...2 General...2 DRAFTING GUIDELINES...3 General...3 Drawing Typical Sections...3 Attaching a Sheet...3 Text Size and Spacing...4 Labeling of

More information

TABLE OF CONTENTS 1200 PLAN PREPARATION

TABLE OF CONTENTS 1200 PLAN PREPARATION 1200 PLAN PREPARATION TABLE OF CONTENTS PAGE 1201 General Plan Sheet Information... 12-1 1201.1 Introduction... 12-1 1201.2 Unit of Measure... 12-1 1201.3 Plan Sheet Materials and File Format... 12-1 1201.4

More information

CMW DELIVERABLES SPECIFICATION Version 1.0

CMW DELIVERABLES SPECIFICATION Version 1.0 CMW DELIVERABLES SPECIFICATION Version 1.0 Code: CMW-CADD-STD-06 June 2012 CONTENTS 1 INTRODUCTION... 3 2 GENERAL... 3 3 GRAPHIC FORMAT... 3 4 CADD STANDARDS... 3 5 DELIVERY MEDIA AND FORMAT... 4 6 DRAWING

More information

REHABILITATING HISTORIC PROPERTIES FOR FEDERAL INVESTMENT TAX CREDITS

REHABILITATING HISTORIC PROPERTIES FOR FEDERAL INVESTMENT TAX CREDITS REHABILITATING HISTORIC PROPERTIES FOR FEDERAL INVESTMENT TAX CREDITS State Historic Preservation Office Oklahoma Historical Society 800 Nazih Zuhdi Drive Oklahoma City, OK 73105 (405) 521-6249 http://www.okhistory.org/shpo

More information

Checklist for Tentative Subdivision Map

Checklist for Tentative Subdivision Map Checklist for Tentative Subdivision Map All submittal information shall be provided to the Community Development Department. All submittal information shall be presented along with the Uniform Application,

More information

Modeling an Airframe Tutorial

Modeling an Airframe Tutorial EAA SOLIDWORKS University p 1/11 Difficulty: Intermediate Time: 1 hour As an Intermediate Tutorial, it is assumed that you have completed the Quick Start Tutorial and know how to sketch in 2D and 3D. If

More information

3. The dimensioning SYMBOLS for arcs and circles should be given:

3. The dimensioning SYMBOLS for arcs and circles should be given: Draft Student Name: Teacher: District: Date: Wake County Test: 9_12 T and I IC61 - Drafting I Test 2 Description: 4.08 Dimensioning Form: 501 1. The MINIMUM amount of space between two, ADJACENT DIMENSION

More information

Chapter 6 Title Blocks

Chapter 6 Title Blocks Chapter 6 Title Blocks In previous exercises, every drawing started by creating a number of layers. This is time consuming and unnecessary. In this exercise, we will start a drawing by defining layers

More information

3. The PAC (Permit Application Center) will notify the design professional of plan review results.

3. The PAC (Permit Application Center) will notify the design professional of plan review results. Planning and Development Dept. Infrastructure Division P.O. Box 11706, or 155 Johnston Street Rock Hill, South Carolina 29731-1706 Phone: 803-329-5515 FAX: 803-329-7228 www.cityofrockhill.com AS-BUILT

More information

Grease Interceptor Design Checklist

Grease Interceptor Design Checklist CHECKLIST C2 Revised 5/2/2016 Grease Interceptor Design Checklist Public Works DISCLAIMER - This checklist is provided to Consulting Engineers for the express purpose of assisting them in compiling private

More information

SECTION D BIM COORDINATION DRAWINGS - CONTRACTORS

SECTION D BIM COORDINATION DRAWINGS - CONTRACTORS END OF SECTION 01 30 00 SECTION 01 31 21-3D BIM COORDINATION DRAWINGS - CONTRACTORS PART 1 - GENERAL 1.01 RELATED DOCUMENTS Attention is directed to Bidding and Contract Requirements, and to Division 1,

More information

Plan Preparation Checklist

Plan Preparation Checklist Appendix D Plan Preparation Checklist It is the responsibility of the Designer to complete and submit this checklist along with all required drawings for OUC (EFP) Review. All drawings submitted for OUC

More information

Student Name: Teacher: Date: District: Rowan. Assessment: 9_12 T and I IC61 - Drafting I Test 2. Description: Drafting 1 - Test 6.

Student Name: Teacher: Date: District: Rowan. Assessment: 9_12 T and I IC61 - Drafting I Test 2. Description: Drafting 1 - Test 6. Student Name: Teacher: Date: District: Rowan Assessment: 9_12 T and I IC61 - Drafting I Test 2 Description: Drafting 1 - Test 6 Form: 501 1. 2X on a hole note means: A. Double the size of the hole. B.

More information

Page 1 of 5. ENGINEERING SKETCHES INFORMATION SHEETS MEL02INF2430 v1.1 HEALTH & SAFETY REQUIREMENTS

Page 1 of 5. ENGINEERING SKETCHES INFORMATION SHEETS MEL02INF2430 v1.1 HEALTH & SAFETY REQUIREMENTS Page 1 of 5 Competenz - N Z Engineering Food & Manufacturing Industry Training Organisation Inc. ENGINEERING SKETCHES INFORMATION SHEETS MEL02INF2430 v1.1 HEALTH & SAFETY REQUIREMENTS RECORDING REQUIREMENTS:

More information

Electrical Overcurrent Studies

Electrical Overcurrent Studies Electrical Overcurrent Studies 11-01-2011 Deliverables associated with electrical overcurrent studies are as follow : a. Draft Reports i. Construction Related Projects have the following draft reports

More information

Ecological Restoration Drafting & Design Guidelines

Ecological Restoration Drafting & Design Guidelines Ecological Restoration Drafting & Design Guidelines Version 2.0 July 2017 Philadelphia Water Ecological Restoration Drafting & Design Guidelines Table of Contents 1.0 INTRODUCTION...2 2.0 GENERAL PLAN

More information

State College Area School District

State College Area School District State College Area School District The following is a guideline for project design submittals to the Facility Committee of the State College Area School District. During the design process the committee

More information

CHAPTER 01 PRESENTATION OF TECHNICAL DRAWING. Prepared by: Sio Sreymean

CHAPTER 01 PRESENTATION OF TECHNICAL DRAWING. Prepared by: Sio Sreymean CHAPTER 01 PRESENTATION OF TECHNICAL DRAWING Prepared by: Sio Sreymean 2015-2016 Why do we need to study this subject? Effectiveness of Graphics Language 1. Try to write a description of this object. 2.

More information

Ohio Department of Transportation, VBA Documentation

Ohio Department of Transportation, VBA Documentation Contents 1.1 Current Versions... 2 1.2 Overview... 3 1.3 Supporting Files and Standards... 4 1.3.1 ODOT_Drainage.cel... 4 1.3.2 ODOT2013.ddb... 5 1.4 ODOT_StormSewerPlan2013.mvba... 6 1.4.1 Mode: Place

More information

ENGINEERING STANDARD FOR DRAFTING FIRST EDITION JANUARY 2012

ENGINEERING STANDARD FOR DRAFTING FIRST EDITION JANUARY 2012 ENGINEERING STANDARD FOR DRAFTING FIRST EDITION JANUARY 2012 This Standard is the property of Iranian Ministry of Petroleum. All rights are reserved to the owner. Neither whole nor any part of this document

More information

Working with Process Flow DiagramsChapter1:

Working with Process Flow DiagramsChapter1: Chapter 1 Working with Process Flow DiagramsChapter1: In this chapter, you learn about designing piping with AutoCAD MEP. The design phase consists of conceptualizing, modeling, and documenting the necessary

More information

Autodesk Advance Steel. Drawing Style Manager s guide

Autodesk Advance Steel. Drawing Style Manager s guide Autodesk Advance Steel Drawing Style Manager s guide TABLE OF CONTENTS Chapter 1 Introduction... 5 Details and Detail Views... 6 Drawing Styles... 6 Drawing Style Manager... 8 Accessing the Drawing Style

More information