Glenco Gas/Liquid Syringes from Spectrum Chromatography
|
|
- Ronald Townsend
- 6 years ago
- Views:
Transcription
1 Glenco Gas/Liquid Syringes from Spectrum Chromatography D Copyright 1996 by Spectrum Chromatography PO Box Houston, TX Phone: (281) (800) (US & Canada) Fax: (281)
2 Introduction Spectrum Chromatography manufactures a variety of syringes for laboratory use. The Gas/Liquid syringes range in volume from 500 µl to 100 ml. Each syringe s Teflon plunger provides a gas- and liquid-tight seal. The syringes are available with either fixed (cemented) needles or with removable, screwhub needles. In addition, syringes are available with either conventional, constant-tension plungers or with adjustable-tensions plungers. 2 Conventional Gas/Liquid Syringes Ideally suited for handling almost any gas or liquid Fixed and interchangeable needle models available Interchangeable plungers with constant-tension seal The Spectrum conventional Gas/Liquid syringes offer the same high degree of resistance to chemical attack as the adjustable plunger seal Gas/Liquid syringes; only borosilicate glass and Teflon are wetted by the fluid. The plunger in these syringes has a flat face which contacts the flat bottom of the barrel assuring that all of the fluid is displaced from the syringe. The barrels and plungers of these syringes are interchangeable within a given size. This allows replacements barrels to be readily obtained in the event of accidental breakage. While these syringes are leak-free to in excess of 30 psig, we do not recommend using them at high pressures. At high pressures the plunger may be accidentally ejected from the barrel creating a hazard. D10122 Gas/Liquid Syringes
3 Adjustable Plunger Seal Gas/Liquid Syringes Ideally suited for handling almost any gas or liquid Fixed and interchangeable needle models available Interchangeable plungers with adjustabletension seal The Spectrum adjustable plunger seal Gas/Liquid syringes offer the highest degree of resistance to chemical attack. Only borosilicate glass and Teflon are wetted by the fluid. The unique adjustable plunger seal features an expanding Teflon seal at the plunger face. The two concentric parts of the plunger shaft may be rotated to expand the Teflon O-rings, ensuring the maintenance of the leak-proof seal. The figure below illustrates the direction in which the two knobs should be turned to tighten the seal. Turning them in the opposite manner will loosen the seal by allowing the O-ring to contract. These syringes, when properly used, are leak-free to in excess of 50 psig. However, using these syringes at high pressures in no recommended; the plunger may become difficult to control and may be launched from the barrel creating a hazard. vc Tightening the Syringe Plunger D10122 Gas/Liquid Syringes 3
4 The plunger in these syringes has a flat face which contacts the flat bottom of the barrel assuring that all of the fluid is displaced from the syringe. The barrels and plungers of these syringes are interchangeable within a given size. This allows replacement barrels to be readily obtained in the event of accidental breakage. Syringe Replacement Parts Replacement plungers and barrels are available for the full line of Gas/Liquid syringes. The same barrels are used both the conventional and the adjustable plunger seal syringes. Replacement barrels with either a threaded tip for use with a removable screw-hub needle or with a fixed 2 x #22 needle are available. Replacement barrels with a 3 x #22 needle are available by special order only. The same plungers are used with both the removable screw-hub needle barrels and the cemented needle barrels. Replacement conventional, as well as adjustable plunger seal, plungers are available. Both flat end (90 ) and sharp (22 ) removable screw-hub needles are available as replacement parts. They are available with a #22 outside diameter (0.028 ), and two different inside diameters, and These needles are supplied with the Teflon sealing washer but not the screw hub nut. Additional screw hub nuts, if required, must be ordered separately. The Teflon seals used in the connection made at the end of the syringe are supplied with each needle and accessory. The are also available separately. 4 D10122 Gas/Liquid Syringes
5 Gas/Liquid Syringe Accessories Spectrum Chromatography offers a variety of accessories which can be used with the removable needle Gas/Liquid syringes. Gas/Liquid syringes may be used with standard Luer hub needles with the aid of the Luer adapter. The adapter screws onto the 1/4-28 threads on the end of the screw-hub Gas/Liquid syringes. It provides a standard male Luer-Lock fitting for use with needles and other Luer-compatible devices. The wetted surfaces in this adapter include Kel-F and chromium plate. Luer-hubbed needles are available from Spectrum Chromatography for use with this adapter. Two different shut-off valves are available for the Gas/Liquid syringes. These may be used for positive fluid control. By filling the syringe and then closing the valve one can be sure that no leakage will occur prior to the desired release of the syringe contents. These valves are constructed entirely of Kel-F and Teflon. They have 1/4-28 threads on both their inlet and outlet so that they will accommodate any accessory or needle which would fit the syringe. When open, the valves have a straight, clear flow-path for minimum dead volume. These valves are able to withstand 200 psig without leakage. For a more permanent syringe seal, a screw-on closure is available for the Gas/Liquid syringes. This Kel-F device screws onto the end of the syringe to seal it. It may also be used in conjunction with a shut-off valve to allow for the ready storage of material in syringes. Fittings for connecting tubing directly to the threads on the end of the Gas/Liquid syringes are available. The flare-tube coupling is designed to mate with most 1/4-28 flare-tube or flangeless fittings which require a flatbottomed receptacle. These include Cheminert and Omnifit fittings. D10122 Gas/Liquid Syringes 5
6 Syringe Guard Station The Syringe Guard Station allows you to store your syringes in a convenient and organized manner. The Spectra/Chrom Syringe Guard Station puts all of those misplaced syringes at your fingertips. No more syringe breakage or loss. Each Syringe Guard Station holds up to ten syringes. It is not designed to accommodate syringes larger than 2.5 ml. 6 D10122 Gas/Liquid Syringes
7 Conventional Gas/Liquid Syringes with Removable Screw Hub Needles and Constant Tension Plunger Glenco Series Needle Grad. Length (in) Needle Part No. Size Div. and Gauge ID x OD(in) µl 1 µl 2 x x µl 1 µl 3 x x µl 2 µl 2 x x µl 2 µl 3 x x µl 5 µl 2 x x µl 5 µl 3 x x µl 10 µl 2 x x µl 10 µl 3 x x ml 10 µl 2 x x ml 10 µl 3 x x ml 50 µl 2 x x ml 0.1 ml 2 x x ml 0.5 ml 2 x x ml 0.5 ml 2 x x ml 1.0 ml 2 x x ml 1.0 ml 2 x x * 2.5 ml 50 µl 2 x x.028 * is supplied with a flat end (90 ) needle, the others with a sharp (22 ) needle. D10122 Gas/Liquid Syringes 7
8 Conventional Gas/Liquid Syringes with Fixed (Cemented) Needles and Constant Tension Plunger (Glenco Series 19930) Needle Grad. Length (in) Needle Part No. Size Div. and Gauge ID x OD(in) µl 1 µl 2 x x µl 2 µl 2 x x µl 5 µl 2 x x µl 10 µl 2 x x ml 10 µl 2 x x ml 50 µl 2 x x ml 0.1 ml 2 x x ml 0.1 ml 2 x x ml 0.5 ml 2 x x ml 1.0 ml 2 x x ml 1.0 ml 2 x x.028 Gas/Liquid Syringes with Removable Screw Hub Needles and Adjustable Plunger (Glenco Series 19925A) Needle Grad. Length (in) Needle Part No. Size Div. and Gauge ID x OD (in) ml 0.1 ml 2 x x ml 0.1 ml 2 x x ml 0.5 ml 2 x x ml 1.0 ml 2 x x ml 1.0 ml 2 x x D10122 Gas/Liquid Syringes
9 Gas/Liquid Syringes with Fixed (Cemented) Needles and Adjustable Plunger (Glenco Series 19930A) Needle Grad. Length (in) Needle Part No. Size Div. and Gauge ID x OD(in) ml 0.1 ml 2 x x ml 0.1 ml 2 x x ml 0.5 ml 2 x x ml 1.0 ml 2 x x ml 1.0 ml 2 x x.028 Replacement Glass Barrels for Gas/Liquid Syringes For use with Syringe With fixed removable needles Size 2" x 22 Needle µl µl µl µl ml ml ml ml ml ml ml D10122 Gas/Liquid Syringes 9
10 Replacement Plungers for Gas/Liquid Syringes Constant Syringe Adjustable Tension Size Tension µl µl µl µl ml ml ml ml ml ml ml Replacement Screw-Hub Needles Flat End (90 ) Sharp (22 ) Length (in) ID x OD Part No. Part No. x Gauge (in) Qty x x x x x x x x x x x x D10122 Gas/Liquid Syringes
11 Screw Hub Nuts and Teflon Seals Part No. Description Qty/pk Screw Hub Nut Teflon Seals 6 Gas/Liquid Syringe Accessories Part No. Description Qty/pk Shut-off Valve with bore Shut-off Valve with bore Male Luer Adapter Female Luer Adapter Syringe Closure Flare-Tube Coupling /8 Flare-Tube Nut /16 Flare-Tube Nut Side port Needle, 2 x 22 2 Syringe Guard Station Part No. Description Syringe Guard Station for up to 10 syringes D10122 Gas/Liquid Syringes 11
12 Glenco is a registered trademark of Spectrum Medical Industries, inc. Kel-F is a registered trademark of 3M Company. Spectra/Chrom is a registered trademark of Spectrum Medical Industries, inc. Teflon is a registered trademark of E.I. du Pont de Nemours & Co., inc. 12 D10122 Gas/Liquid Syringes
Gastight Syringes. A guide to syringe terminations and needle points can be found on page Series
Gastight Syringes Gastight syringes are ideal for dispensing both liquids and gases. They have a precision-machined polymer plunger tip, often PTFE, which creates a leak-free seal. With the tight fit,
More informationPTFE Tip, Gas-Tight Syringes
PTFE Tip, Suitable for gases or liquids. High accuracy of dispensed volumes. Interchangeable barrels, plungers, and tips extend performance and increase cost-effectiveness. Volume Needle Needle Needle
More informationFITTINGS & GAUGES 20,000 PSI
PRESSURE GAUGE Features 4" high visibility face with laminated safety glass dial cover Accurate within +/- 0.5% of full scale range Stainless steel case and internals Heavy-duty movement Glycerine-filled
More informationCaution: Installation and Operation Instructions. Locking Mechanism (if supplied) Set Screws Backed Out. Mounting Orientation
Genie Probe Regulator (GPR)/ Genie Probe (GP2)/ Genie Probe for Composite Sampler (CSA)/ And (Model H) Installation and Operation Instructions Caution: Not designed for external fire. Prior to use in a
More informationGP-SD GENIE PROBE SMALL DIAMETER
For GENIE PROBE SMALL DIAMETER Installation and Operation Instructions 2 for s Locking Mechanism (if supplied) Set Screws Backed Out To ensure that the is Locking never accidentally loosened or Mechanism
More information5.1 MUELLER CORPORATION VALVES. MUELLER 300 Ball Type Corporation Valves
MUELLER CORPORATION VALVES 5.1 Shaded area indicates changes Rev. 4-14 Machine inserted corporation stops were developed by Hieronymus Mueller in conjunction with his development of the drilling and tapping
More informationOperating, Servicing, and Safety Manual Model # 100 Standard Hydraulic Tubing Notcher Model #100-U Heavy Duty Hydraulic Tubing Notcher
Operating, Servicing, and Safety Manual Model # 100 Standard Hydraulic Tubing Notcher Model #100-U Heavy Duty Hydraulic Tubing Notcher Model # 100 Standard Model #100-U Heavy Duty CAUTION: Read and Understand
More informationThe Virgo/Libra Steam Engine
The Virgo/Libra Steam Engine Congratulations on becoming the owner of a Virgo or Libra Steam Engine. With careful use and maintenance it will give many years of satisfying performance. Contents 1) Notes
More informationLPK1550 Hydraulic Crimping Tool 15-ton
SERVICE MANUAL LPK1550 Hydraulic Crimping Tool 15-ton Serial Code FYF Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register
More informationCV Control Valves Installation and Operation Manual
CV00 - Control Valves Installation and Operation Manual Overview Warning: This bulletin should be used by experienced personnel as a guide to the installation of the Armstrong CV00 Control Valve. Selection
More informationOperation Manual Panel Mounting Gas Pressure Regulators
687 Technology Way Napa, CA 94558 Phone: (707) 259-0102 FAX: (707) 259-0117 www.aptech-online.com Table of Contents: A. General information... 1 B. Panel Mount Nut - AP/AZ/AK/SL Model Regulators... 1 C.
More informationUnderstanding pipe threads: types and designations
WHITE PAPER 8008 Understanding pipe threads: types and designations By Mark Schmidt Applications Engineer CPC (Colder Products Company) Different types of screw threads have evolved for fastening and hydraulic
More informationH4670/42192 Submersible Trash Pump
SERVICE MANUAL H4670/42192 Submersible Trash Pump Serial Code GLW Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. 99916070 REV
More informationInstallation Instructions
Contemporary Round Floor Mounted Tub Filler Thank you for selecting American-Standard... the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly-- please read
More informationMODEL T TON HYDRAULIC PRESS INSTRUCTIONS (For Machines Mfd. Since 10/17)
MODEL T1241 20-TON HYDRAULIC PRESS INSTRUCTIONS (For Machines Mfd. Since 10/17) For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Identification
More informationSR-1.0 Manual, a.doc 11/14/2006 Page 1 of 17
SR-1.0 Manual, 20061108a.doc 11/14/2006 Page 1 of 17 ASSEMBLY INSTRUCTIONS, MODEL SR-1.0 EXTRUSION HEAD STREAMLINE EXTRUSION, INC. Following is a set of photos and verbal descriptions for assembling the
More informationEngineering Data Single Reduction Parts List Item # Description Basic Single Reduction Unit 1. Gear Housing 2. Pipe Plug 3. Vent Plug 4. Splash Guard
Engineering Data Single Reduction Parts List Item # Description Basic Single Reduction Unit 1. Gear Housing 2. Pipe Plug 3. Vent Plug 4. Splash Guard 5. Input Cover 6. O-Ring 7. Hex Head Cap Screw 8. Input
More informationUsing Your Chip Priming Station
s1 Using Your Chip Priming Station The Chip Priming Station, part number 5065-4401, is for use with the Agilent 2100 Bioanalyzer LabChip Kits. Refer to Figure 1 and 2 for a picture of the Chip Priming
More informationGeneral Information. Ball Curb Valve
General Information 1. All Jones Curb Valves are manufactured in accordance with the AWWA Standard C-800-latest revision. 1. Copper Alloy CDA No. C83600 (85-5-5-5) 2. Copper Alloy CDA No. 89520 (Low Lead)
More informationAdjustable Center Crossheads Operations Manual
Plastic Extrusion Tooling Specialists ph: 800.272.8878 Adjustable Center Crossheads Operations Manual BH25, BH30, BH75, BH225, BH250 & BH750 B&H TOOL COMPANY FIRST IN EXTRUSION TOOLING Dear Customer, Thank
More informationInstallation Instructions
Contemporary Square Floor Mounted Tub Filler Thank you for selecting American-Standard... the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly-- please read
More informationSeries B Medical Gas Service Outlet Upgrade Kits
Installation Instructions Series B Medical Gas Service Outlet Upgrade Kits For additional information concerning operation of Puritan Bennett Series B Quick-Connect Outlet Valves, refer to Operating Instructions
More informationSERVICE INSTRUCTIONS Model 9670 Lubricant Pump
TM TM SERVICE INSTRUCTIONS Model 9670 Lubricant Pump 9670 DESCRIPTION Model 9670 Lubricant Pump is designed to pump light to heavy oils directly from the original container. This design features a 10:1
More informationBHJ Products, Inc. Parts List & Instructions
Product Name: O-Ring Groove Cutter Adjustable Tool Block Upgrade Page 1 of 5 Prototype Kit Contents: 1x Adjustable Tool Block 1x Adjustable Tool Holder 1x Graduated Adjusting Screw 1x 1/8 Registration
More informationMUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extension Sections. Reliable Connections
insertion Instructions manual MUELLER Improved, Centurion Series, Modern Improved, and 107 table of contents PAGE Centurion Series Fire Hydrant Adding an Extension 2-3 Improved Fire Hydrant Inserting Extension
More informationUnderwater Probes. Description
Underwater Probes Description 3300 XL underwater probes are designed specifically for applications involving constant exposure to liquids, such as those in hydroelectric plants or sewage treatment facilities.
More informationDust RIGHT. Shop Vacuum Dust Hose Reel Instructions. For safe and effective operation, please read these instructions fully before use.
Dust RIGHT Shop Vacuum Dust Hose Reel Instructions For safe and effective operation, please read these instructions fully before use. GENERAL SAFETY WARNINGS This tool is designed for specific applications
More informationMUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extention Sections. Reliable Connections
insertion Instructions manual MUELLER Improved, Centurion Series, Modern Improved, and 107 table of contents PAGE Centurion Series Fire Hydrant Adding an Extention 2-3 Improved Fire Hydrant Inserting Extention
More informationOWNER'S MANUAL JST-48 Sliding Table
OWNER'S MANUAL JST-48 Sliding Table (shown mounted on JET 708663PK) JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 Phone:253-351-6000 A WMH Company Auburn, WA 98071-1349 Fax: 1-800-274-6840 www.jettools.com
More informationRhino r VE/CE Pneumatic Level Detect Modules. Description S S. The assembly detects two conditions during the downward movement of the follower:
Rhino r VE/CE Pneumatic Level Detect Modules Description See Figure 1. Level Detect modules use roller plunger limit switches on guide rails to monitor the distance between the bottom of the follower and
More informationBHJ Products, Inc. Parts List & Instructions
Product Name: O-Ring Groove Cutter Page 1 of 6 Kit Contents: 1x Cutter Head Assembly with Handle & Adjustable Tool Block 1x Graduated Adjusting Screw 1x Adjustable Tool Holder 1x Carbide Insert (Size of
More informationElectron Microscopy Sciences
Electron Microscopy Sciences INSTRUCTIONAL MANUAL CAT. 50120-10 Model 900 Grinding and Polishing Machine P.O. Box 550 s1560 Industry Road s Hatfield PA 19440 1 Introduction The Model 900 is a small, compact
More informationSupport Stands & Conveyor Mountings. Parts, Assembly & Maintenance Manual. Steel Support Stand. Aluminum Support Stand Rev.
Support Stands & Conveyor Mountings Parts, Assembly & Maintenance Manual Aluminum Support Stand Steel Support Stand -00 Rev. B Table of Contents Safe Practices............................... Foreword....................................
More informationFord Water Meter Couplings & Accessories
Section H 2/2001 Ford Water Meter Couplings & Accessories The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260/563-3171 FAX: 1-800-826-3487 Overseas
More informationaccidents which arise due to nonobservance and the safety information herein. SPECIFICATIONS
7 TON ELECTRIC LOG SPLITTER Model: 05620 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.
More informationH8508 Impact Wrench SERVICE MANUAL. Model (Serial Code FWN) Model (Serial Code FWP)
SERVICE MANUAL H8508 Impact Wrench Model 48755 (Serial Code FWN) Model 48760 (Serial Code FWP) Read and understand all of the instructions and safety information in this manual before operating or servicing
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Square Free Standing Floor Mount Tub Filler Model D35900900 Thank you for selecting DXV. To ensure that your installation proceeds smoothly, please read these instructions carefully
More informationTYPE 3740/3740D WET/DRY RUNNING CARTRIDGE SPLIT SEAL
1 Foreword These instructions are provided to familiarize the user with the seal and its designated use. The instructions must be read and applied whenever work is done on the seal, and must be kept available
More informationBETTIS SERVICE INSTRUCTIONS FOR MODELS G01 THROUGH G10 SERIES HYDRAULIC SPRING RETURN ACTUATORS WITH M11 HYDRAULIC OVERRIDE
ENGLISH LANUAGE BETTIS SERVICE INSTRUCTIONS FOR MODELS G01 THROUGH G10 SERIES HYDRAULIC SPRING RETURN ACTUATORS WITH M11 HYDRAULIC OVERRIDE PART NUMBER: 127072E REVISION: A DATE: December 2001 Page 1 of
More informationHOLE CUTTER SHARPENER ASSEMBLY & SERVICE MANUAL
HOLE CUTTER SHARPENER ASSEMBLY & SERVICE MANUAL WARNING You must thoroughly read and understand this manual before operating the equipment, paying particular attention to the Warning & Safety instructions.
More informationMUELLER GAS. DH-5 Drilling Machine. For use on 1 1 /2 & 2 Line Stopper Fittings. Reliable Connections. General Information 2
operating Instructions manual MUELLER GAS TAble of contents PAGE DH-5 Drilling Machine For use on 1 1 /2 & 2 Line Stopper Fittings General Information 2 Installing and Stopping-off 1 1 /2 and 2 Line Stopper
More informationHydraulic Adapters STEEL PIPE ADAPTERS NPTF DRY SEAL PIPE ASSEMBLY INSTRUCTIONS. Steel Pipe Adapters. Steel Pipe Adapters. Hydraulic.
CONFORMANCE SAE J54 for hex nipples, expanders, elbows, tees and crosses SAE J54, J50 and J5 for bushing and plugs. Temperature Range -65 0 F to +400 0 F MATERIALS - SAE L4 carbon steel plated zinc with
More informationSECTION 7. SAFETYING
9/8/98 AC 43.13-1B SECTION 7. SAFETYING 7-122. GENERAL. The word safetying is a term universally used in the aircraft industry. Briefly, safetying is defined as: Securing by various means any nut, bolt,
More informationMECHANICAL ASSEMBLY John Wiley & Sons, Inc. M. P. Groover, Fundamentals of Modern Manufacturing 2/e
MECHANICAL ASSEMBLY Threaded Fasteners Rivets and Eyelets Assembly Methods Based on Interference Fits Other Mechanical Fastening Methods Molding Inserts and Integral Fasteners Design for Assembly Mechanical
More informationOWNERS MANUAL. Model No LB. POLY PRO SPIKER/SPREADER. CAUTION: Read Rules for Safe Operation and Instructions Carefully
OWNERS MANUAL Model No. -0301 CAUTION: Read Rules for Safe Operation and Instructions Carefully 17 LB. POLY PRO SPIKER/SPREADER Safety Assembly Operation Maintenance Parts PRINTED IN U.S.A. FORM NO. 78
More informationAustin Standing Seam Awning with Overhead Braces Assembly and Installation Instructions. Assembly Instructions
Austin Standing Seam Awning with Overhead Braces Assembly and Installation Instructions Be sure to use safety glasses when assembling and installing the awning. Some metal parts may have sharp edges. Use
More information3 Emergency Breakaway Coupling
SM64227 July 2008 Applicable addition manuals: N/A Aerospace Group Conveyance Systems Division Carter Ground Fueling Maintenance & Repair Manual 3 Emergency Breakaway Coupling Model 64227 Table of Contents
More information20 TON HyDRAULIC SHOP PRESS with GRID GUARD 06/2015 INSTRUCTION MANUAL MODEL: KHP-20T-GG COPYRIGHT 2015 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
06/2015 20 TON HyDRAULIC SHOP PRESS with GRID GUARD MODEL: KHP-20T-GG INSTRUCTION MANUAL COPYRIGHT 2015 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC. warranty INFORMATION 2-yEAR LIMITED WARRANTY FOR THIS
More informationINSTALLATION INSTRUCTIONS
Flash Shower Valve Rough With Screwdriver Stops Thank you for selecting American-Standard... the benchmark of fine quality for over 0 years. To ensure that your installation proceeds smoothly-please read
More informationLANVRT10. Instructions. Lankota Vertical Unload Auger Removal Tool for JD 00 to S series combines. 270 West Park Avenue Huron, SD
LANVRT10 Instructions Lankota Vertical Unload Auger Removal Tool for JD 00 to S series combines 270 West Park Avenue Huron, SD 57350 866-526-5682 Page 1 Numerical Parts List Part Numbers Description Quantity
More informationSquare Wheel Belt Grinder Models: 4103, 4106, and 4126AC
This Manual is Bookmarked Operating Instructions Parts Manual Square Wheel Belt Grinder Models: 4103, 4106, and 4126AC WHM TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Ph.: 800-274-6848 www.wmhtoolgroup.com
More informationUnderwater Probes. Bently Nevada* Asset Condition Monitoring. Description
Underwater Probes Bently Nevada* Asset Condition Monitoring Description 3300 XL underwater probes are designed specifically for applications involving constant exposure to liquids, such as those in hydroelectric
More informationINSTRUCTIONS FOR AIRFLEX 36WCBEP/36WCSEP WEAR PLATE REPLACEMENT USING GASKET SEALING TAPE
INSTRUCTIONS FOR AIRFLEX 36WCBEP/36WCSEP WEAR PLATE REPLACEMENT USING GASKET SEALING TAPE The material included in this kit is to be used for WC styles of brakes that are designed or upgraded to the EP
More informationStaple Specification:
H-1027, H-1028 H-3064 PNEUMATIC STICK STAPLER stapler specifications Dimensions: L x H x W 13.5 x 8.75 x 6" Weight (Without Fasteners) Compressed Air: Maximum psi: Recommended Operating Pressure: Air Consumption:
More informationELECTRIC TUBE ROLLER
41238-0000 ELECTRIC TUBE ROLLER OPERATING INSTRUCTIONS & SERVICE MANUAL Rev: A, 8/20/2007 TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE USER MUST READ AND UNDERSTAND OPERATOR S MANUAL. Thomas C. Wilson,
More informationEMO. Service Instruction. created by Frank Weithöner. Table of contents: Special Tools Assembling Mixing Chamber
EMO Service Instruction created by Frank Weithöner Table of contents: - Special Tools Disassembling Mixing Chamber Assembling Mixing Chamber Adjustment Rotor / Level Indicator Unit Temperature Compensating
More informationMSR/MSB Mechanical Setting Tool
Tech Unit No: 0620000004 Revision: C Approved By: Quality Engineer Date: 201-1-9 MSR/MSB Mechanical Setting Tool FEATURES: Special designed Bow Spring provides positive control and allows one size Mechanical
More informationMSR/MSB Mechanical Setting Tool
Tech Unit No: 0620000004 Revision: B Approved By: Quality Engineer Date: 2014-12-16 MSR/MSB Mechanical Setting Tool FEATURES: Special designed Bow Spring provides positive control and allows one size Mechanical
More informationRim-Lock Door Set Installation Instructions
Rim-Lock Door Set Installation Instructions Let s get started Check Your Parts List Two Doorknobs with Set Screws B. Doorknob Spindle C. Rim Lock with Mounting Screws D. Keeper with Mounting Screws E.
More informationDCD Design & Model K (400) Part #: Pull Type Cable Lasher Operating Instructions. Manufacturing Ltd. ENGINEERING SOLUTIONS
Model K (400) Part #: 61500-000 Pull Type Cable Lasher Operating Instructions Specifications: Lasher Weight: 40 lbs Shipping Weight: approximately 75 lbs (shipped in storage chest) Dimensions: 19 long
More information25000 Series Lo-T TM Butterfly Control Valve Instructions
November 2001 25000 Series Lo-T TM Butterfly Control Valve Instructions Instruction No. 25.1:IM PRELIMINARY STEPS Before installation, note the flow direction arrow on the valve body. The flow should enter
More informationDust RIGHT. Shop Vacuum Dust Hose Reel Instructions
Dust RIGHT Shop Vacuum Dust Hose Reel Instructions Review full instruction manual prior to use for important safety information. Always check Rockler.com to confi rm that you are using the most recent manual
More informationJ D SQUARED INC. NOTCH MASTER Tube and Pipe Notcher Operating Instructions
Copyright (c) 2006 J D SQUARED INC. www.jd2.com NOTCH MASTER Tube and Pipe Notcher Operating Instructions Angled Notches PATENT PENDING Straight Notches Offset Notches Tube Clamp Slider Tube Clamp Exploded
More informationFluid Sealing Association
Fluid Sealing Association STANDARD FSA-MG-501-02 STANDARD TEST METHOD FOR INWARD BUCKLING OF SPIRAL-WOUND GASKETS 994 Old Eagle School Road, Suite 1019 Wayne, Pennsylvania 19087-1866 Phone: (610) 971-4850
More informationTYPE 3740XL EXTRA LARGE WET RUNNING CARTRIDGE SPLIT SEAL
1 Foreword These instructions are provided to familiarize the user with the seal and its designated use. The instructions must be read and applied whenever work is done on the seal, and must be kept available
More informationHARDINGE Installation booklet For:
HARDINGE Installation booklet For: L Flange Nose Dead-Length Collet Adaptation Chucks Draw Collet Read the enclosed instructions and recommendations before any installations WARRANTY & RETURN PROCEDURES
More informationMade in USA. Valves VALVES FOR INSTRUMENTATION & PROCESS SYSTEMS
Made in USA Valves VALVES FOR INSTRUMENTATION & PROESS SYSTEMS SSP Fittings orp. Table of ontents FloLok Product Overview... 3 FloLok Selection Guide... 11 Two-Way Ball Valves... 12 Three-Way Ball Valves...
More informationJD-12. Instruction & Parts Manual
JD-12 Instruction & Parts Manual Framon Manufacturing Company, Inc. 909 W Washington Avenue Alpena, MI 49707 Phone: 989-354-5623 Fax: 989-354-4238 E-mail: support@framon.com Website: www.framon.com The
More informationInstruction Manual. EASY / WHISPER 2, 3, 4 & 5 Blades. Scan the QR code with a mobile device to view the installation video.
Instruction Manual EASY / WHISPER 2, 3, 4 & 5 Blades Scan the QR code with a mobile device to view the installation video. www.max-prop.com 1) INTRODUCTION: Thank you for having chosen a Max-Prop automatic
More informationDue to possible damage in shipping, the vertical stop assembly has been removed from this machine.
Due to possible damage in shipping, the vertical stop assembly has been removed from this machine. To assemble, insert the threaded rod through the shroud opening in the top of the machine. Start the four
More informationCopyright 2007 ES Manufacturing, Inc th Street North St. Petersburg, FL 33713
e-mail sales@esmfg.com US/Canada 800-55ES-MFG Documentation & Warranty Packet MB110 ( 600 rpm s) Thank you for purchasing the MB110 If properly operated and maintained, this Heavy Duty Fiber Cutter will
More informationSAVE THIS FOR FUTURE REFERENCE THIS PRODUCT IS FOR PROFESSIONAL LABORATORY USE ONLY USER'S MANUAL
DENTAL, INC. TECHNICAL BULLETIN G801-022510 5860 FLYNN CREEK ROAD READ ALL INSTRUCTIONS P.O. BOX 106 BEFORE PROCEEDING COMPTCHE, CALIFORNIA, U.S.A. 95427-0106 SAVE THIS FOR FUTURE REFERENCE www.wellsdental.com
More informationSPECIFICATIONS. The WM-6XL Long Wm. Malcolm Telescopic Riflescope Instruction Manual WARNING:
The WM-6XL Long Wm. Malcolm Telescopic Riflescope Instruction Manual SPECIFICATIONS Power: 6X Objective: 17mm Length: 30 in. Weight: 1.85 lb. (29.60 oz.) Eye relief: approx. 4.5 in. Reticle: Fine Crosshair
More informationRiser Extension INSTALLATION GUIDE 40100AX35 / 40100AX18. Manual 40100X35-8
Riser Extension INSTALLATION GUIDE 40100AX35 / 40100AX18 Manual 40100X35-8 3 2 4 Access covers with bolts supplied with Interceptor 1 5 14 6 11 15 Sampling Port/Cleanout cap supplied with Interceptor 12
More informationReliance SG800 Series Steel Water Gage Valves
Installation, Operation, & Maintenance Instructions R500.541D1 10/16/2016 Reliance SG800 Series Steel Water Gage Valves Note: Design variations in Steel Water Gage Valves necessitate typical illustrations,
More information400 SERIES GRINDER PUMPS 41502, 42202,43302, AND MODELS
Section: MOYNO 500 PUMPS Page: 1 of 6 Date: March 1, 1998 SERVICE MANUAL MOYNO 500 PUMPS 400 SERIES GRINDER PUMPS 41502, 42202,43302, AND 44402 MODELS DESIGN FEATURES Housing: Cast iron Pump Rotor: Chrome
More informationTB404 Conductivity sensors. Perfect for use in standard to highly corrosive solutions
Data sheet TB404 Conductivity sensors Toroidal Perfect for use in standard to highly corrosive solutions Greatly reduces coating and other fouling problems Inductive measurement technique yields a solution
More informationHigh Speed Air Turbine Handpiece
OPERATION MANUAL High Speed Air Turbine Handpiece Please read this Operation Manual carefully before use and file for future reference. Handpiece should not be used with friction grip burs exceeding 18.5
More informationOPERATOR'S MANUAL ROUTER MOUNTING KIT
OPERATOR'S MANUAL MOUNTING KIT 4950301 (FOR USE WITH BT3000 AND BT3100 TABLE SAWS) Your new router mounting kit has been engineered and manufactured to Ryobi's high standard for dependability, ease of
More informationMounting Instructions For 3-Piece Namur Style Mounting Bracket To 2-Way 60 Series Valves
Mounting Instructions For 3-Piece Namur Style Mounting Bracket To 2-Way 60 Series Valves NOTE: These instructions apply only to 60 series ball valves with bodies containing external mounting nibs. External
More informationChiltern Model Steam Engines
Chiltern Model Steam Engines Mill Twin Cylinder Model Steam Engine v2 Assembly Instructions v1.0 Notes: 1. In overview the engine should first be assembled "dry" with no oil/lubricants, thread lock or
More informationGCX Mounting Assembly Installation Guide. Drager Narcomed GS Anesthesia Machines with Philips MP60/70 IntelliVue Patient Monitor Kit
GCX Mounting Assembly Installation Guide Drager Narcomed GS Anesthesia Machines with Philips MP60/70 IntelliVue Patient Monitor Kit Philips MP60/70 IntelliVue Patient Monitor AGM Philips M8048A Flexible
More informationHARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet
HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet Read the enclosed instructions and recommendations before any installations CONTENTS Dead-Length Collet Adaptation
More informationPressure Balance Shower Only Dual Control (Volume & Temperature) Ceramic Disc Cartridge Platinum Shower Trim Kit
Shower Only PL8900-00 & TR-SH Pressure Balance Shower Only Dual Control (Volume & Temperature) Ceramic Disc Cartridge Platinum Shower Trim Kit - Installation Instructions Before Your Installation Read
More informationSERVICE MANUAL LHFS
SERVICE MANUAL LHFS-210003 Pruner Serial Code FFD Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product at www.greenlee.com
More informationPURESTREAM SYSTEM - ASSEMBLY GUIDE
PURESTREAM SYSTEM - ASSEMBLY GUIDE VISIT OUR WEBSITE : www.cagpurification.com our installment procedure videos in the PURESTREAM Piping section. NECESSARY TOOLS FOR INSTALLATION We suggest the use of
More informationUsing Your Chip Priming Station
Using Your Chip Priming Station The Chip Priming Station (5065-4401), is for use with the Agilent 2100 Bioanalyzer Analysis Kits. Refer to Figure 1 on page 2 for a picture of the Chip Priming Station.
More informationOPERATING INSTRUCTIONS AND PARTS LISTS
3889560 REEL ALIGNMENT GAGE OPERATING INSTRUCTIONS AND PARTS LISTS WARNING You must thoroughly read and understand this manual before operating the equipment, paying particular attention to the Warning
More informationInstruction Manual for MHE Products DeepWater2 PushPoint Sampler Ver. 2.0 November 21, 2016
Instruction Manual for MHE Products DeepWater2 PushPoint Sampler Ver. 2.0 November 21, 2016 The DeepWater2 is heavier-duty a version of the PushPoint Sampler made of stainless steel pipe instead of SS
More informationHYDRAULIC FLARING TOOL
Item #31562 HYDRAULIC FLARING TOOL INSTRUCTIONS The FAIRMOUNT HYDRAULIC FLARING TOOL provides the ability to produce repeatable, perfect, OE-precision brake and fuel line flares in steel and soft-metal
More informationAngle Grinder. Model Visit our website at:
Angle Grinder Safety Guard Model 45921 Installation Instructions Note: Cutting Blade and Angle Grinder sold separately. Visit our website at: http://www.harborfreight.com Read this material before using
More information30DC Speed Lathe Manual
30DC Speed Lathe Manual The Crozier Model 30DC Speed Lathe is our most popular model. It has many standard features not found on any other machine in its class or price range. Standard Features 3/4 HP
More informationSERVICE MANUAL CLINTON FEED OFF THE ARM CHAIN CUTTER WITH EXTERNAL AIR DRIVE MODEL 2115FOTA-V FOR UNION SPECIAL 35800, & YAMATO FD-62 ML2115-7A
ML2115-7A CLINTON FEED OFF THE ARM CHAIN CUTTER WITH EXTERNAL AIR DRIVE MODEL 2115FOTA-V FOR UNION SPECIAL 35800, 36200 & YAMATO FD-62 SERVICE MANUAL 40-0164-01 ML2115-8E I. GENERAL INFORMATION A. The
More informationChin Strap, Sealed Pull Pins and Swing Catch for Fiberglass Helmets. Contents
Chin Strap Chin Strap, Sealed Pull Pins and Swing Catch for Fiberglass Helmets Contents BTM-1 1.1 Chin Strap BTM-4 1.2.3.1 Preparation BTM-1 1.1.1 Chin Strap Removal BTM-4 1.2.3.2 Disassembly BTM-1 BTM-2
More informationFlat Sample Holder Part Number
Flat Sample Holder Part Number 990-00403 (Patent Pending) Operator s Manual Copyright 2016 Gamry Instruments, Inc. April 8, 2016 988-00043 Rev. 1 If You Have Problems Please visit our service and support
More informationBand-Master ATS Nano Pneumatic Banding Tool Operating Instructions
Band-Master ATS 601-118 Nano Pneumatic Banding Tool CONTENTS 601-118 Overview... 3 Safety.... 5 Initial Tool Set-up... 5 Regulator assembly mounting... 5 Attach tool head to regulator.... 6 Operating instructions...
More informationInspection. Assembly Install the springs. 1. Discard the 0-rings. 2. Clean all parts in cleaning solvent.
6010-34 Inspection 3. Install the springs. 1. Discard the 0-rings. 2. Clean all parts in cleaning solvent. 3. If spring test equipment is available, check the tension of each spring according to the specifications
More informationINSTRUCTION MANUAL. In vivo Test Apparatus for 305B Muscle Lever Systems
INSTRUCTION MANUAL Model 806A In vivo Test Apparatus for 305B Muscle Lever Systems May 18, 2005, Revision 3 Copyright 2005 Aurora Scientific Inc. Aurora Scientific Inc. 360 Industrial Parkway S., Unit
More information8 TONNE LOG SPLITTER
8 TONNE LOG SPLITTER MODEL NO: LOGBUSTER 9 PART NO: 3402043 OPERATION & MAINTENANCE INSTRUCTIONS LS03/16 INTRODUCTION Thank you for purchasing this CLARKE 8 Tonne Log Splitter. Before attempting to use
More informationM-5 PRO CORE BORE PARTS LIST DRILLING MACHINE. (March 2017) Part #
M- PRO CORE BORE DRILLING MACHINE PARTS LIST (March 07) Part #809 Table of Contents Description Page No. Carriage Assembly....... - Combo Base Assembly....... - 7 Anchor Base Assembly........8 Anchor
More information