Accurately capture signals with Smart Noise Reduction

Transcription

1 Smart Fiber Amplifier Units ENX-FA Long Range for Small Object Detection Rapid analysis with dual digital display White characters on black display for high visibility Reduced set-up time with push button teach Selectable power and response times to match your application Tailor machine functions with timer options Minimize debris build-up and LED deterioration for longer life Network compatibility for data management CSM_ENX-FA_E9I-E-0 For the most recent information on ls that have been certified for safety standards, refer to your OMR website. Refer to the Safety Precautions on page 7. Accurately capture signals with Smart Noise Reduction.5 Times Powerful coupling module Without GIGA RAY With GIGA RAY By increasing the number of samples and the threshold margin, the influences of noise are greatly reduced., high precision The lens and reflector focus light beams for uniform brightness. Adjust the light intesity to accurately detect fast-moving workpieces. A response time of 0µ s can be achieved. in highspeed. Ordering Information Fiber Amplifier Units (Dimensions pages 9 and 0) Type Connecting Appearance Inputs/outputs NPN output PNP output Standard ls Pre-wired ( m) output ENX-FA M ENX-FA-5 M CE NEW * ENX-FA4 M --- Wire-saving Connector output ENX-FA6 ENX-FA8 Pre-wired ( m) outputs + input ENX-FA M ENX-FA5 M Advanced ls Wire-saving Connector output + input ENX-FA7 ENX-FA9 outputs ENX-FA7TW ENX-FA9TW output + input ENX-FA4 ENX-FA54 M8 Connector outputs --- ENX-FA54TW *. This type can prevent mutual interference for two units in the SHS.

2 Type Connecting Appearance Inputs/outputs NPN output PNP output Infrared ls Pre-wired ( m) output ENX-FAH M CE ENX-FAH4 M CE NEW NEW Wire-saving Connector output ENX-FAH6 CE ENX-FAH8 CE NEW NEW Analog output ls Pre-wired ( m) outputs ENX-FAAN M CE ENX-FA4AN M CE NEW NEW for Sensor Communications Unit * Connector for Sensor Communications Unit *. A Sensor Communications Unit is required if you want to use the Fiber Amplifier Unit on a network. Accessories (Sold Separately) Wire-saving Connectors (Required for ls for Wire-saving Connectors.) (Dimensions page ) Connectors are not provided with the Fiber Amplifier Unit and mu st be ordered separately. Note: Protective stickers are provide d. --- ENX-FA0 ENX-FAH0 CE Type Appearance Cable length No. of conductors Applicable Fiber Amplifier Units NEW Master Connector Slave Connector 4 EX-CN EX-CN ENX-FA7 ENX-FA7TW ENX-FA9 ENX-FA9TW m Master Connector Slave Connector EX-CN EX-CN ENX-FA6 ENX-FA8 Sensor I/O Connectors (Required for ls for M8 Connectors.) (Dimensions page ) Connectors are not provided with the Fiber Amplifier Unit and must be ordered separately. Size Cable Appearance Cable type m XSF-M4-40-A Straight 5m XSF-M4-405-A M8 Standard cable 4-wire m XSF-M4-40-A L-shaped 5m XSF-M4-405-A

3 Mounting Bracket (Dimensions page ) A Mounting Bracket is not provided with the Fiber Amplifier Unit. It must be ordered separately as required. Appearance Quantity Related Products Sensor Communications Units Type Appearance E9-L4 Sensor Communications Unit for EtherCAT ENW-ECT DIN Track (Dimensions page ) A DIN Track is not provided with the Fiber Amplifier Unit. It must be ordered separately as required. Appearance Type Quantity Sensor Communications Unit for CompoNet ENW-CRT * Shallow type, total length: m Shallow type, total length: 0.5 m PFP-00N PFP-50N Sensor Communications Unit for CC-Link ENW-CCL Deep type, total length: m PFP-00N End Plate (Dimensions page ) Two End Plates are provided with the Sensor Communications Unit. End Plates are not provided with the Fiber Amplifier Unit. They must be ordered separately as required. Appearance Quantity PFP-M Cover Attach these Covers to Amplifier Units. Order a Cover when required, e.g., if you lose the covers. Appearance Quantity E9-G5 FOR ENX-FA NEW Distributed Sensor Unit * ENW-DS Refer to your OMR website for details. *. Only ENX-FA0 can be connected to ENW-CRT. *. The Distributed Sensor Unit can be connected to any of the Sensor Communications Units. EtherCAT is a registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany. CompoNet is a registered trademark of the ODVA. CC-Link is a registered trademark of Mitsubishi Electric Corporation. The trademark is managed by the CC-Link Partner Association.

4 Ratings and Specifications Standard ls/ Advanced ls/ Infrared ls Item Giga-power 0 (GIGA) *. This type can prevent mutual interference for two units in the SHS. *. At Power supply voltage of 0 to 0 VDC Standard s: Normal : 990 mw max. (Current consumption: ma max. at 0 VDC, 65 ma max. at 0 VDC) Eco function : 780 mw max. (Current consumption: 6 ma max. at 0 VDC, 4 ma max. at 0 VDC) Eco function LO : 840 mw max. (Current consumption: 8 ma max. at 0 VDC, 45 ma max. at 0 VDC) Advanced s: Normal :,00 mw max. (Current consumption: 4 ma max. at 0 VDC, 67 ma max. at 0 VDC) Eco function : 80 mw max. (Current consumption: 7 ma max. at 0 VDC, 44 ma max. at 0 VDC) Eco function LO : 870 mw max. (Current consumption: 9 ma max. at 0 VDC, 48 ma max. at 0 VDC) Infrared ls: Normal :,60 mw max. (Current consumption: 4 ma max. at 0 VDC, 80 ma max. at 0 VDC) Eco function :,050 mw max. (Current consumption: 5 ma max. at 0 VDC, 60 ma max. at 0 VDC) Eco function LO :,40 mw max. (Current consumption: 8 ma max. at 0 VDC, 70 ma max. at 0 VDC) *. The following details apply to the input. *-.Input time is 5 ms ()/() only when (in tune) or (in PtUn) input is selected. *4. The tuning will not change the number of units. The least unit count among the mutual interference prevention units of ENX and ENC. Check the mutual interference prevention unit count and response speed of each l. ENX-FA Type Standard ls Advanced ls Infrared ls NPN output ENX-FA ENX-FA6 ENX-FA-5 * ENX-FA ENX-FA7 ENX-FA7TW ENX-FA4 --- ENX-FAH ENX-FAH6 PNP output ENX-FA4 ENX-FA8 --- ENX-FA5 ENX-FA9 ENX-FA9TW ENX-FA54 ENX-FA54TW ENX-FAH4 ENX-FAH8 Connecting Pre-wired Wire-saving Connector Pre-wired Pre-wired Wire-saving Connector M8 Connector Pre-wired Wire-saving Connector Inputs/ s output outputs output outputs output outputs outputs outputs External inputs --- input input --- input Light source (wavelength) Red, 4-element LED (65 nm) Infrared LED (870nm) Power supply voltage 0 to 0 VDC, including 0% ripple (p-p) At Power supply voltage of 4 VDC Standard s: Normal : 840 mw max. (Current consumption at 5 ma max.) Eco function : 650 mw max. (Current consumption at 7 ma max.) Eco function LO : 750 mw max. (Current consumption at ma max.) Advanced s or for Sensor Communications Unit: Power consumption * Normal : 90 mw max. (Current consumption at 8 ma max.) Eco function : 680 mw max. (Current consumption at 8 ma max.) Eco function LO : 800 mw max. (Current consumption at ma max.) Infrared ls: Normal : 080 mw max. (Current consumption at 45 ma max.) Eco function : 90 mw max. (Current consumption at 8 ma max.) Eco function LO : 00 mw max. (Current consumption at 4 ma max.) power supply voltage: 0 VDC max., open-collector output (depends on the NPN/PNP output format) current: Groups of to Amplifier Units: 00 ma max., Groups of 4 to 0 Amplifier Units: 0 ma max. Control output Residual voltage: At load current of less than 0 ma: V max. At load current of 0 to 00 ma: V max. current: 0. ma max. External inputs --- Refer to *. --- Refer to *. --- Indicators Protection circuits (SHS) Response time 7-segment displays (Sub digital display: green, Main digital display: white) Display direction: Switchable between normal and reversed. OUT indicator, L/D indicator, ST indicator (blue), DPC indicator (green), and OUT selection indicator (orange, only on ls with outputs) Power supply reverse polarity protection, output short-circuit protection, and output reve rse polarity protection or reset for l with output: 0 μs (Super High Speed (SHS) of ENX-FA-5 is 60 μs each), with outputs: μs or reset: 50 μs (HS) Standard or reset: ms (Stnd) Giga-power or reset: 6 ms (GIGA) Smart Tuning (-point tuning, full auto tuning, position tuning, maximum sensitivity tuning, power tuning, or percentage tuning (-99% to 99%)) or manual adjustment Sensitivity adjustment Maximum connectable Units 0 No. of Units for mutual interference prevention *4 NPN PNP (SHS) (HS) Standard (Stnd) 0 Note: units when the detection is set to Super High Speed (SHS), and for other ls, the mutual interference prevention function is disabled. 0 0 Contact input (relay or switch) Non-contact input () Input time *- : Shorted to 0 V (Sourcing current: ma max.). : Open or shorted to Vcc. : Shorted to Vcc (Sinking current: ma max.). : Open or shorted to 0 V. :.5 V max. (Sourcing current: ma max.) : Vcc.5 V to Vcc (Leakage current: 0. ma max.) : Vcc.5 V to Vcc (Sinking current: ma max.) :.5 V max. (Leakage current: 0. ma max.) : 9 ms min. : 0 ms min. 4

5 Item Functions Type Standard ls Advanced ls Infrared ls NPN output ENX-FA ENX-FA6 ENX-FA-5 * ENX-FA ENX-FA7 ENX-FA7TW ENX-FA4 --- ENX-FAH ENX-FAH6 PNP output ENX-FA4 ENX-FA8 --- ENX-FA5 ENX-FA9 ENX-FA9TW ENX-FA54 ENX-FA54TW ENX-FAH4 ENX-FAH8 Connectin g Pre-wired Wire-saving Connector *5. The bank is not reset by the user reset function or saved by the user save function. *6. Eco LO is supported for Amplifier Units manufactured in July 04 or later. *7. When the number of connected units is or more, the ambient temperature is less than 50 C. Pre-wired Pre-wired Wire-saving Connector M8 Connector Pre-wired Wire-saving Connector Automatic power control (APC) Always enabled. Dynamic power control (DPC) Provided Timer Select from timer disabled, -delay, -delay, one-shot, or -delay + -delay timer: to 9,999 ms Zero reset Negative values can be displayed. (Threshold value is shifted.) Resetting settings *5 Select from initial reset (factory defaults) or user reset (saved settings). Eco *6 Select from (digital display lit), Eco (digital display not lit), and Eco LO (digital display dimmed). Bank switching Select from banks to 4. Power tuning Select from, or Execution on power-up. Select from or. Select from normal detection, area detection or differential detection. Select from normal detection or area detection. --- External input --- Select from normal detection, alarm output, error output or differential detection. --- Select from input, tuning, power tuning, emission, zero reset, or bank switching. Select from normal detection, alarm output ---, error output or differential detection. Select from input, tuning, power tuning, --- emission, zero reset, or bank switching. Select from normal detection, alarm output, error output or differential detection. Hysteresis width Select from standard setting or user setting. For a user setting, the hysteresis width can be set from 0 to 9,999. Ambient illumination (Receiver side) Incandescent lamp: 0,000 lx max., Sunlight: 0,000 lx max. Ambient temperature range *7 Ambient humidity range Altitude Installation environment Insulation resistance Dielectric strength Vibration resistance (destruction) Shock resistance (destruction) Weight (packed state/ Sensor only) Case Materials Cover Cable Accessories Operating: Groups of or Amplifier Units: 5 to 55 C, Groups of to 0 Amplifier Units: 5 to 50 C, Groups of to 6 Amplifier Units: 5 to 45 C, Groups of 7 to 0 Amplifier Units: 5 to 40 C Storage: 0 to 70 C (with no icing or condensation) Operating and storage: 5 to 85% (with no condensation) within the surrounding air temperature range shown above,000 m max. Pollution degree 0 MΩ min. (at 500 VDC),000 VAC at 50/60 Hz for min 0 to 55 Hz with a.5-mm double amplitude for hours each in X, Y, and Z directions 500 m/s for times each in X, Y, and Z directions Approx. 5 g/ approx. 75 g Approx. 60g/ approx. 0g Polycarbonate (PC) Polycarbonate (PC) PVC Instruction Manual Approx. 5 g/ approx. 75 g Approx. 5 g/ approx. 75 g Approx. 60g/ approx. 0g Approx. 65 g/ approx. 5 g Approx. 5 g/ approx. 75 g Approx. 60g/ approx. 0g 5

6 Analog output ls/ for Sensor Communications Unit Type Analog output ls for Sensor Communications Unit NPN output ENX-FAAN ENX-FA0 ENX-FAH0 PNP output ENX-FA4AN Item Connecting Pre-wired Connector for Sensor Communications Unit Inputs/ s outputs outputs External inputs * --- * Light source (wavelength) Red, 4-element LED (65 nm) Infrared LED (870nm) Power supply voltage 0 to 0 VDC, including 0% ripple (p-p) Supplied from the connector through the communication units. Power consumption * Control output Analog output Indicators Protection circuits Control output Response time Super-high-speed (SHS) At Power supply voltage of 4 VDC Normal : 960 mw max. (Current consumption at 40 ma max.) Eco function : 770 mw max. (Current consumption at ma max.) Eco function LO : 870 mw max. (Current consumption at 6 ma max.) power supply voltage: 0 VDC max., open-collector output (depends on the NPN/PNP output format) current: Groups of to Amplifier Units: 00 ma max., Groups of 4 to 0 Amplifier Units: 0 ma max. Residual voltage: ( At load current of less than 0 ma: V max. ) At load current of 0 to 00 ma: V max. current: 0. ma max. Voltage output: -5 VDC (0 kω or more connected load), temperature characteristics: 0.% F.S. / C At Power supply voltage of 4 VDC Normal : 90 mw max. (Current consumption at 8 ma max.) Eco function : 680 mw max. (Current consumption at 8 ma max.) Eco function LO : 800 mw max. (Current consumption at ma max.) *. Two sensor outputs are allocated in the programmable logic controller PLC I/O table. PLC operation via Communications Unit enables reading detected values and changing settings. *. At Power supply voltage of 0 to 0 VDC Analog output ls: Normal :,080 mw max. (Current consumption: 6 ma max. at 0 VDC, 75 ma max. at 0 VDC) Eco function : 840 mw max. (Current consumption: 8 ma max. at 0 VDC, 55 ma max. at 0 VDC) Eco function LO : 960 mw max. (Current consumption: ma max. at 0 VDC, 65 ma max. at 0 VDC) *. The tuning will not change the number of units. The least unit count among the mutual interference prevention units of ENX and ENC. Check the mutual interference prevention unit count and response speed of each l At Power supply voltage of 4 VDC Normal :,080 mw max. (Current consumption at 45 ma max.) Eco function : 90 mw max. (Current consumption at 8 ma max.) Eco function LO :,00 mw max. (Current consumption at 4 ma max.) 7-segment displays (Sub digital display: green, Main digital display: white) Display direction: Switchable between normal and reversed. OUT indicator, L/D indicator, ST indicator (blue), DPC indicator (green), and OUT selection indicator (orange, only on ls with outputs) Power supply reverse polarity protection, output short-circuit Power supply reverse polarity protection and output short-circuit protection protection, and output reve rse polarity protection or reset: 80 μs or reset: μs (HS) or reset: 50μs or reset: 50 μs Standard (Stnd) or reset: ms or reset: ms Giga-power (GIGA) or reset: 6 ms or reset: 6 ms Sensitivity adjustment Smart Tuning (-point tuning, full auto tuning, position tuning, maximum sensitivity tuning, power tuning, percentage tuning ( 99% to 99%)) or manual adjustment With ENW-ECT: 0 units (When connected to an OMR NJ-series Controller.) Maximum connectable Units 0 With ENW-CRT: 6 units (Note: ENX-FAH0 can not be connected.) With ENW-CCL: 6 units No. of Units for mutual interference prevention * Super-high-speed (SHS) (HS) 0 Standard (Stnd) 0 Giga-power (GIGA) 0 (The mutual interference prevention function is disabled if the detection is set to super-high-speed.) 0 6

7 Item Functions NPN output PNP output Type Analog output ls for Sensor Communications Unit ENX-FAAN ENX-FA4AN *4. The bank is not reset by the user reset function or saved by the user save function. *5. When the number of connected units is or more, the ambient temperature is less than 50 C. ENX-FA0 ENX-FAH0 Connecting Pre-wired Connector for Sensor Communications Unit Automatic power control (APC) Always enabled. Dynamic power control (DPC) Provided Timer Select from timer disabled, -delay, -delay, one-shot, or -delay + -delay timer: to 9,999 ms Zero reset Negative values can be displayed. (Threshold value is shifted.) Resetting settings *4 Select from initial reset (factory defaults) or user reset (saved settings). Eco Select from (digital display lit), Eco (digital display not lit), and Eco LO (digital display dimmed). Bank switching Select from banks to 4. Power tuning Select from or. Select from normal detection or area detection. Select from Analog scaling or Analog offset. Select from normal detection, alarm output, error output or differential detection (ENX-FA0 only). Hysteresis width Select from standard setting or user setting. For a user setting, the hysteresis width can be set from 0 to 9,999. Ambient illumination (Receiver side) Incandescent lamp: 0,000 lx max., Sunlight: 0,000 lx max. Ambient temperature range *5 Operating: Groups of or Amplifier Units: 5 to 55 C, Groups of to 0 Amplifier Units: 5 to 50 C, Groups of to 6 Amplifier Units: 5 to 45 C, Groups of 7 to 0 Amplifier Units: 5 to 40 C Storage: 0 to 70 C (with no icing or condensation) Operating: Groups of or Amplifier Units: 0 to 55 C, Groups of to 0 Amplifier Units: 0 to 50 C, Groups of to 6 Amplifier Units: 0 to 45 C, Groups of 7 to 0 Amplifier Units: 0 to 40 C Storage: 0 to 70 C (with no icing or condensation) Ambient humidity range Operating and storage: 5 to 85% (with no condensation) within the surrounding air temperature range shown above Altitude,000 m max. Installation environment Pollution degree Insulation resistance 0 MΩ min. (at 500 VDC) Dielectric strength,000 VAC at 50/60 Hz for min Vibration resistance (destruction) 0 to 55 Hz with a.5-mm double amplitude for hours each in X, Y, and Z directions Shock resistance (destruction) 500 m/s for times each in X, Y, and Z directions 50 m/s for times each in X, Y, and Z directions Weight (packed state/sensor only) Approx. 5 g/approx. 75 g Approx. 65 g/approx. 5 g Approx. 65 g/approx. 5 g Case Polycarbonate (PC) Materials Cover Polycarbonate (PC) Cable PVC Accessories Instruction Manual 7

8 Distances Standard ls/ Advanced ls/ Analog output ls Threaded s Reflective direction *. The fiber length is m on each side, so the sensing distance is given as 4,000 mm. Cylindrical s Reflective Right-angle Straight Right-angle Straight Size dia. Size M4 M Giga distance (mm) Standard ENX-FA E-TN M,000,500, E-LTN M 4,000 * 4,000 *, E-TR M,000,500, E-LT M 4,000 * 4,000 * 4,000 *,080 E-LTR M 4,000 * 4,000 *, E-CN M E-CN M M4 E-DN M, M6 M E-CN M, E-LDN M, E-DR M E-C M E-CM M M4 E-DR M M6 direction E-DR M, E-CC00 M, E-LD M, E-LDR M, Giga distance (mm) Standard E-TR M dia. E-TB M, dia..5 dia..5 dia dia. dia. dia dia. E-TR M,000,500, Side-view E-T4LR M, E-DB M E-D4M M E-DR M E-DB M E-DL M, E-D M Flat s Reflective direction Giga distance (mm) Standard E-T5XR M,000,500, Side-view Flat-view E-T5YR M E-T5ZR M, E-D5XR M, Side-view Flat-view E-D5YR M E-D5ZR M

9 Sleeve s Reflective direction Side-view Side-view Giga distance (mm) Standard E-T4R M E-T4E M E-T M E-T-S M E-TC00BR M,000,500, E-D4R M E-D4-S M E-D4M M E-D M 9 6 E-D M E-D-S 0.5M E-D-S 0.5M E-DC00F4R M E-D-S M E-D-S M E-DC00BR M, E-D5-S M Small-spot, Reflective s Type Spot diameter distance (mm) Center s distance (mm) Giga Standard Variable spot 0. to 0.6 dia. 6 to 5 E-C4 M + E9-FA Spot diameter of 0. to 0.6 mm at 6 to 5 mm. 0. to.6 dia. 0 to 0 E-C4 M + E9-F7 Spot diameter of 0. to.6 mm at 0 to 0 mm. Parallel light 4 dia. 0 to 0 E-C M + E9-FC E-CN M + E9-FC Spot diameter of 4 mm max. at 0 to 0 mm. Integrated lens 0. dia. 5 E-C4S M Spot diameter of 0. mm at 5 mm. 6 dia. 50 E-L5 M Spot diameter of 6 mm at 50 mm. 0. dia. E-C4 M + E9-FA-5 Spot diameter of 0. mm at 7 mm. 0.5 dia. 7 E-C M + E9-FA-5 E-CN M + E9-FA-5 Spot diameter of 0.5 mm at 7 mm. 0. dia. E-C4 M + E9-FB Spot diameter of 0. mm at 7 mm. Small-spot 7 E-C M + E9-FB 0.5 dia. Spot diameter of 0.5 mm at 7 mm. E-CN M + E9-FB dia. 50 E-CC00 M + E9-F8 E-CN M + E9-F8 Spot diameter of mm at 50 mm. 9

10 High-power Beam s Type ls with integrated lens ls with lenses Reflective ls with integrated lens direction *. The fiber length is 0 m on each side, so the sensing distance is given as 0,000 mm. *. The fiber length is m on each side, so the sensing distance is given as 4,000 mm. Narrow View s Aperture angle s *. The fiber length is m on each side, so the sensing distance is given as 4,000 mm. s for Detection without Background Interference Giga distance (mm) Standard Right-angle 5 E-LTN M 4,000 * 4,000 *, E-T7L 0M 0,000 * 0,000 * 0,000 * 8,000 5 E-LT M 4,000 * 4,000 * 4,000 *,080 E-LTR M 4,000 * 4,000 *, Side-view 0 E-T4 M 4,000 * 4,000 * 4,000 *,800 Right-angle E-TN M + E9-F 4,000 * 4,000 * 4,000 *,000 6 E-TN M + E9-F6 4,000 * 4,000 * 4,000 *,600 E-TR M + E9-F 4,000 * 4,000 * 4,000 *,000 6 E-TR M + E9-F6 4,000 * 4,000 * 4,000 *,600 Side-view 60 E-TR M + E9-F,70, E-T M + E9-F 4,000 * 4,000 * 4,000 *,860 6 E-T M + E9-F6 4,000 * 4,000 * 4,000 * 4,000 * Side-view 60 E-T M + E9-F,450,980,90 0 E-T5R M + E9-F 4,000 * 4,000 * 4,000 *,500 6 E-T5R M + E9-F6 4,000 * 4,000 * 4,000 * 4,000 * Side-view 60 E-T5R M + E9-F,00, E-T8R-S M + E9-F 4,000 * 4,000 * 4,000 *,000 6 E-T8R-S M + E9-F6 4,000 * 4,000 * 4,000 *,800 Side-view 60 E-T8R-S M + E9-F, E-T6-S M + E9-F 4,000 * 4,000 * 4,000 *,800 6 E-T6-S M + E9-F6 4,000 * 4,000 * 4,000 *,00 Side-view 60 E-T6-S M + E9-F,50, E-T5 M + E9-F- 4,000 * 4,000 *,450,400 6 E-T5 M + E9-F6 4,000 * 4,000 * 4,000 * 4,000 * 4 E-D6 M 40 to 4,000 * 40 to,00 40 to,50 40 to 480 direction Side-view Aperture angle.5 E-A0 M E-A0- M s Giga distance (mm) Standard 4,000 *,670, E-A04 M,90, E-T4SR M 4,000 *,00, E-T4S M 4,000 *,900, E-TS M 4,000 * 4,000 *,750,000 direction Flat-view Giga distance (mm) Standard E-L6-N M 0 to 5 0 to E-L4S M 0 to 4 Side-view E-L5L M 5.4 to 9 (center 7.) Transparent Object Detection (Retro-reflective s) Retro-reflective Feature Size s Giga distance (mm) Standard Limitedreflective E-C M + Film detection M E9-FR + E9-RP7 Square --- E-R6 5M 50 to,500 Threaded E-R M 0 to 70 0 to 50 Hex-shaped M6 E-LRNP M + E9-RP,00,800,

11 Transparent Object Detection (Limited-reflective s) Limitedreflective Feature direction Small size Flat-view distance (mm) Giga Standard Super-high-speed E-L4S M 0 to 4 Standard E-L6-N M 0 to 5 0 to Glass substrate alignment, 70 C E-A08 M 0 to Standard/long-distance E-A M to Side-view form Side-view E-L5L M 5.4 to 9 (center 7.) Glass substrate mapping, 70 C E-A09 M 5 to Chemical-resistant, Oil-resistant s Type direction distance (mm) Giga Standard Super-high-speed Oil-resistant Right-angle E-TNF M 4,000 * 4,000 * 4,000 *,00 Chemical/oil-resistant Chemical/oil-resistant at 50 C E-TF M 4,000 * 4,000 * 4,000 *,600 E-TF M 4,000 * 4,000 *,900,000 Side-view E-T4F M,00, E-T5F M 4,000 * 4,000 *, Semiconductors: Cleaning, developing, and etching; 60 C E-LFP 5M 8 to 0 mm from tip of lens (Recommended sensing distance: mm), 9 to mm from center of mounting hole A (Recommended sensing distance: mm) Reflective Semiconductors: Resist stripping; 85 C E-LFS 5M 8 to 0 mm from tip of lens (Recommended sensing distance: mm), to 44 mm from center of mounting hole A (Recommended sensing distance: 5 mm) Chemical/oil-resistant E-DF M --- * Chemical-resistant cable E-DU M, *. The fiber length is m on each side, so the sensing distance is given as 4,000 mm. *. Even if there is no sensing object, the Sensor will detect light that is reflected by the fluororesin. Bending-resistant s Size distance (mm) Giga Standard Super-high-speed.5 dia. E-TB M, M E-T M M4 E-T M,750,00,50 60 Square E-T5XB M Reflective.5 dia. E-DB M M E-D M dia. E-DB M M4 E-DB M M6 E-D M, Square E-D5XB M Heat-resistant s Reflective Heat-resistant temperature *. The fiber length is m on each side, so the sensing distance is given as 4,000 mm. distance (mm) Giga Standard Super-high-speed 00 C E-T5R M,400, C E-T5 M 4,000 *,50, C E-T8R-S M, C E-T6-S M,50, C E-D5R M, C E-D5 M, C E-D8R-S M C 50 C E-A08H M 0 to E-A09H M 0 to 0 (center 5) --- E-D6-S M E-D6-S M C E-D7-S M

12 Area Detection s *. The fiber length is m on each side, so the sensing distance is given as 4,000 mm. Liquid-level Detection s Vacuum-resistant s Type width Area mm *. The fiber length is m on each side, so the sensing distance is given as,000 mm. s for FPD, Semiconductors, and Solar Cells *. The fiber length is m on each side, so the sensing distance is given as 4,000 mm. distance (mm) Giga Standard Super-high-speed E-T6PR M 4,000 *,550, E-T6JR M 4,000 *,50, mm E-T6WR M 4,000 *,900, Reflective Array mm E-D6P M, Tube-mounting Liquid contact (heat-resistant up to 00 C) Limitedreflective Tube diameter Feature., 6.4, or 9.5 dia 8 to 0 dia Stable residual quantity detection Mounting at multiple levels E-A0 5M E-L5T M distance (mm) Giga Standard Super-high-speed Applicable tube: Transparent tube with a diameter of., 6.4, or 9.5 mm, Recommended wall thickness: mm Applicable tube: Transparent tube with a diameter of 8 to 0 mm, Recommended wall thickness: mm No restrictions Large tubes E-D6T 5M Applicable tube: Transparent tube (no restrictions on diameter) E-D8F 4M Liquid-contact type distance (mm) Heat-resistant temperature Giga Standard Super-high-speed E-T5V M, C E-T5V M + E9-FV,000 *,000 *,000 * C E-T84SV M,000 *, Application Operating temperature Glass presence detection 70 C Glass substrate alignment Glass substrate mapping Wet processes: Cleaning, Resist developing and etching Wet process: Resist stripping distance (mm) Giga Standard Super-high-speed E-L6-N M 0 to 5 0 to E-A08 M 0 to C E-A08H M E-A M to C E-A09 M 5 to C E-A09H M 0 to 0 (center 5) C E-LFP 5M 8 to 0 mm from tip of lens (Recommended sensing distance: mm), 9 to mm from center of mounting hole A (Recommended sensing distance: mm) 85 C E-LFS 5M 8 to 0 mm from tip of lens (Recommended sensing distance: mm), to 44 mm from center of mounting hole A (Recommended sensing distance: 5 mm) E-A0 M E-A0- M 4,000 *,670, Wafer mapping 70 C E-A04 M,90, E-T4SR M 4,000 *,00, E-T4S M 4,000 *,900,60 700

13 Infrared ls Threaded s Reflective Cylindrical s direction Size Right-angle Straight Straight Size dia. M4 E-TN M E-TR M Giga distance (mm) Standard M E-C M M6 direction E-DR M E-CC00 M Giga distance (mm) Standard E-TR M Side-view E-T4LR M Reflective dia. E-DL M Flat s Reflective direction Giga distance (mm) Standard E-T5XR M Side-view Flat-view E-T5YR M E-T5ZR M E-D5XR M Side-view Flat-view E-D5YR M E-D5ZR M Sleeve s direction High-power Beam s Giga distance (mm) Standard E-TC00BR M Reflective E-DC00BR M Type direction Aperture angle s ls with integrated lens Giga distance (mm) Standard Side-view 0 E-T4 M

14 ENX-FA I/O Circuit Diagrams NPN Operation Light- ENX-FA ENX-FA6 ENX-FA-5 ENX-FAH ENX-FAH6 Timing chart (Between brown and Dark- (Between brown and Light- ch/ ch (Between brown and black leads) ENX-FA Dark- ch/ ch (Between brown and black leads) Light- (Between brown and ENX-FA7 ENX-FA4 Dark- Light- ENX-FA7TW (Between brown and ch/ ch (Between brown and black leads) Dark- ch/ ch (Between brown and black leads) Light- (Between brown and ENX-FAAN Dark- (Between brown and L/D indicator L lit. circuit Display OUT indicator Brown Black Control output Photoelectric sensor main circuit Blue D lit. L lit. Display OUT indicator OUT indicator Brown Black Control output Orange ch Control output ch Pink Photoelectric sensor main circuit Display OUT indicator L lit. 4 Photoelectric sensor main circuit M8 Connector Pin Arrangement L lit. Display OUT indicator OUT indicator Photoelectric sensor main circuit Brown Black Control output Orange External input Blue 4 Brown Black Control output Orange ch Control output ch Display OUT indicator 0 to 0 VDC Brown Black Photoelectric sensor main circuit D lit. 0 to 0 VDC Blue D lit. L lit. 0 to 0 VDC External input Blue D lit. D lit. 0 to 0 VDC Control output Orange Analog output 0kΩ min. 0 to 0 VDC Blue 4

15 ENX-FA PNP Operation Light- ENX-FA4 ENX-FA8 ENX-FAH4 ENX-FAH8 Dark- Light- Timing chart L/D indicator L lit. Dark- Display OUT indicator (Between blue and Brown Control Black output Photoelectric sensor main circuit 0 to 0 VDC Blue D lit. (Between blue and ch/ ch L lit. ch/ ch s OUT indicator Display OUT indicator (Between blue and black leads) ENX-FA5 circuit Brown External Pink input Control output Black ch Control output Orange ch Photoelectric sensor main circuit Blue 0 to 0 VDC D lit. (Between blue and black leads) Light- ENX-FA9 ENX-FA54 Dark- Light- Display OUT indicator L lit. Photoelectric sensor main circuit (Between blue and Dark- 4 D lit. External Orange input Control Black output 0 to 0 VDC M8 Connector Pin Arrangement Blue 4 (Between blue and ch/ ch ch/ ch s OUT indicator Display L lit. (Between blue and black leads) ENX-FA9TW ENX-FA54TW Brown OUT indicator Control output Black ch Control output Orange ch Photoelectric sensor main circuit 4 D lit. Brown M8 Connector Pin Arrangement Blue 0 to 0 VDC 4 (Between blue and black leads) Light- ENX-FA4AN Dark- L lit. 表示部 OUT表示灯 橙 Brown Orange Analog output (Between blue and Photoelectric sensor main circuit Black Control output Blue 0 to 0 VDC 0kΩ min. D lit. (Between blue and 5

16 Plug (Sensor I/O Connector) 4 Terminal number 4 XSF-M4-40-A XSF-M4-405-A XSF-M4-40-A XSF-M4-405-A Wire color Brown White Blue Black Wire color Connection pin Application Brown Power supply (+V) White External input / Blue Power supply (0 V) Black 4 Nomenclature ENX-FA/FA4/FA6/FA8/FA7/FA9/FA4/FA54/ FA-5/FAH/FAH4/FAH6/FAH8/FAAN/FA4AN [L/D Indicator] Indicates the setting status: Light- (L) or Dark- (D). [OUT Indicator] Turns when the output is. [DPC Indicator] Turns when Dynamic Power Control is effective. [ST Indicator] Turns when Smart Tuning is in progress. [ L/D Button] Use to switch between Light- (L) and Dark- (D). [ Tune Button] Threshold Level Green digital display Executes Smart Tuning. Incident Level White digital display [ MODE Button] Use to switch between Detection Mode and Setting Mode. [+ UP/DOWN Button] Used to fine-tune the threshold or change set values. ENX-FA/FA5/FA7TW/FA9TW/FA54TW/FA0/FAH0 [L/D Indicator] Indicates the setting status: Light- (L) or Dark- (D). [OUT Indicator/OUT Indicator] Turns when OUT or OUT is. [DPC Indicator] Turns when Dynamic Power Control is effective. [ST Indicator] Turns when Smart Tuning is in progress. [ L/D Button] Use to switch between Light- (L) and Dark- (D). [ Tune Button] Executes Smart Tuning. Threshold Level Green digital display [OUT Selection Indicator/OUT Selection Indicator] The indicator for the selected output channel is lit. Incident Level White digital display [ MODE Button] Use to switch between Detection Mode and Setting Mode, and use to switch between OUT and OUT. [+ UP/DOWN Button] Used to fine-tune the threshold or change set values. 6

17 Safety Precautions Be sure to read the precautions for all ls in the website at: Warning Indications WARNING Precautions for Safe Use Precautions for Correct Use Warning level Indicates a potentially hazardous situation which, if not avoided, will result in minor or rate injury, or may result in serious injury or death. Additionally, there may be significant property damage. Supplementary comments on what to do or avoid doing, to use the product safely. Supplementary comments on what to do or avoid doing, to prevent failure to operate, malfunction or undesirable effect on product performance. Meaning of Product Safety Symbols General prohibition Indicates the instructions of unspecified prohibited action. Caution, explosion Indicates the possibility of explosion under specific conditions. Caution, fire Indicates the possibility of fire under specific conditions. WARNING This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. Do not use the product with voltage in excess of the rated voltage. Excess voltage may result in malfunction or fire. Never use the product with an AC power supply. Otherwise, explosion may result. Precautions for Safe Use ENX-FA The following precautions must be observed to ensure safe operation of the Amplifier Unit. Doing so may cause damage or fire.. Do not install the product in the following locations. Locations subject to direct sunlight Locations subject to condensation due to high humidity Locations subject to corrosive gas Locations subject to vibration or mechanical shocks exceeding the rated values Locations subject to exposure to water, oil, chemicals Locations subject to stream Locations subjected to strong magnetic field or electric field. Do not use the product in environments subject to flammable or explosive gases.. Do not use the product in any atmosphere or environment that exceeds the ratings. 4. To secure the safety of operation and maintenance, do not install the product close to high-voltage devices and power devices. 5. High-voltage lines and power lines must be wired separately from the product. Wiring them together or placing them in the same duct may cause induction, resulting in malfunction or damage. 6. Do not apply any load exceeding the ratings. Otherwise, damage or fire may result. 7. Do not short the load. Otherwise, damage or fire may result. 8. Connect the load correctly. 9. Do not miswire such as the polarity of the power supply. 0.Do not use the product if the case is damaged..burn injury may occur. The product surface temperature rises depending on application conditions, such as the ambient temperature and the power supply voltage. Attention must be paid during operation or cleaning..when setting the sensor, be sure to check safety such as by stopping the equipment..be sure to turn off the power supply before connecting or disconnecting wires. 4.Do not attempt to disassemble, repair, or modify the product in any way. 5.When disposing of the product, treat it as industrial waste. 6.Do not use the Sensor in water, rainfall, or outdoors. 7.Use the product in the IP54 enclosure. 8.UL Standard Certification (Applicable s: ENX-FA//4/5 Only) Only the sensors with Enhanced UL Certification Mark are certified by UL. They are intended to be supplied by a "Class circuit". When used in United States and Canada, Please use the same Class source for input and output.the overcurrent protection current rating is A max. They were evaluated as Open type and shall be installed within a enclosure. 7

18 Precautions for Correct Use. Be sure to mount the unit to the DIN track until it clicks.. When using the Amplifier Units with Wire-saving Connectors, attach the protective stickers (provided with EX-CN-series Connectors) on the unused power pins to prevent electrical shock and short circuiting. When using the Amplifier Units with Connectors for Communications Units, attach the protective caps (provided with ENW-series Sensor Communications Unit). Amplifier Unit with Wiresaving Connector Amplifier Unit with Connector for Communications Unit Protective sticker Power supply connecting terminals Protective cap. The length for the cable extension must be 0 m or less (or less than 0 m for S-mark certified ls). Be sure to use a cable of at least 0. mm for extension. The power voltage must be 4 to 0 V when connecting amplifier units with extension cable and wire-saving connector. 4. Do not apply the forces on the cord exceeding the following limits: Pull: 40N; torque: 0.N m; pressure: 0N; bending: 9.4N 5. Do not apply excessive force such as tension, compression or torsion to the Amplifier Unit with the Fiber Unit fixed to the Amplifier Unit. 6. Always keep the protective cover in place when using the Amplifier Unit. Not doing so may cause malfunction. 7. It may take time until the received light intensity and measured value become stable immediately after the power is turned on depending on use environment. 8. The product is ready to operate 00 ms after the power supply is turned. 9. The Mobile Console EX-MC, EX-MC-SV and EX-MC- S cannot be connected. 0.The mutual interference prevention function does not work when in combination with EC/EC/EX..If the unit receives excessive sensor light, the mutual interference prevention function may not work properly, resulting in malfunction of the unit. In such case, increase the threshold..standard ls and Advanced ls The Sensor Communication Unit EX-DRT-S, EX-CRT, EX- ECT and ENW cannot be connected. for Sensor Communication Unit (ENX-FA0) The Sensor Communication Unit ENW can be connected. EX-DRT-S, EX-CRT, EX-ECT cannot be connected..if you notice an abnormal condition such as a strange odor, extreme heating of the unit, or smoke immediately stop using the product, turn off the power, and consult your dealer. 4.Do not use thinner, benzene, acetone, and lamp oil for cleaning. 8

19 Dimensions Fiber Amplifier Units ENX-FA (Unit: mm) Tolerance class IT6 applies to dimensions in this data sheet unless otherwise specified. Pre-wired Amplifier Units ENX-FA(-5)/FA4/ L/D indicator DPC indicator ST indicator.7 7. OUT selection indicator OUT indicator OUT indicator ENX-FA/FA5 7.8 L/D indicator DPC indicator ST indicator *Cable Specifications ENX-FA4 ENX-FA ENX-FA5 Outer diameter No. of conductors 4.0 dia. 4.0 dia. 5 Others Conductor cross-section: 0. mm Insulator dia.: 0.9 mm Standard cable length: m Minimum bending radius: mm 0 OUT indicator 5. Threshold level (green, digital) Incident level (white, digital) Mounted to DIN Track OUT selection indicator Threshold level (green, digital) 47. (max. value with cover open) 70 (max. value with cover open) Incident level (white, digital) 5. With Mounting Bracket Attached (max. value with cover open) 4.5 Two,.4-dia..5.5 fiber unit holes (6.5) (7) (6.5) (7) * * Fiber Attachment (E9-F9) attached 0.5 (7.9) 7.8 (0.) Optical communications Two,. dia. (mounting holes) 0.5 (9.4) 6 4. Optical communications E9-L4 Mounting Bracket (sold separately, SUS04) PFP-@N DIN Track (sold separately) Mounting Holes Two, M holes 6 (9.9) 6 Amplifier Units with Wire-saving Connectors ENX-FA6 ENX-FA7(TW) ENX-FA6/FA7(TW)/FA8 ENX-FA8 /FA9(TW)/FAH6/FAH8 ENX-FA9(TW) DPC indicator ENX-FAH6 ENX-FAH8 L/D indicator.7 7. OUT indicator Threshold level (green, digital) ST indicator Incident level (white, digital) OUT selection indicator OUT indicator OUT indicator OUT selection indicator Threshold level (green, digital) ENX-FA7TW/FA9TW 7.8 L/D indicator DPC indicator ST indicator Incident level (white, digital) *Cable Specifications Outer diameter No. of conductors EX-CN.6 dia. EX-CN EX-CN 4.0 dia. EX-CN 4 0 Mounted to DIN Track With Mounting Bracket Attached (max. value with cover open) 70 (max. value with cover open) 5. (75.) 04.8 (max. value with cover open) 4.5 Two,.4-dia..5 fiber unit holes (6.5) (7).4 * ().5 (6.5) (7).4 * () 5.7 With Fiber Attachment (E9-F9) attached 0.5 (7.9) (.8) (75.) PFP-@N DIN Track (sold separately) Optical communications Wire-saving Connector (sold separately) Two,. dia. (mounting holes) 0.5 (9.4) Wire-saving Connector (sold separately) Optical communications E9-L4 Mounting Bracket (sold separately, SUS04) Mounting Holes Two, M holes (9.9) 6 6 9

20 Amplifier Units with M8 Connectors ENX-FA4 ENX-FA54 ENX-FA54TW ENX-FA4/FA54 L/D indicator DPC indicator ST indicator OUT selection indicator OUT indicator ENX-FA54TW 7.8 L/D indicator DPC indicator ST indicator Connector pin arrangement OUT indicator OUT indicator Threshold level (green, digital) 5. Incident level (white, digital) OUT selection indicator Threshold level (green, digital) Incident level (white, digital) 0 5. Mounted to DIN Track 47. (max. value with cover open) 70 (max. value with cover open) With Mounting Bracket Attached (max. value with cover open) 4.5 Two,.4-dia. fiber unit holes.5 (6.5) (5.7) PFP-@N DIN Track (sold separately) 0. Optical communications M8 Connector (9.4) Two,. dia. 7.9 (mounting holes) E9-L4 Mounting Bracket (sold separately, SUS04) Mounting Holes Two, M holes Amplifier Unit with Connector for Sensor Communications Unit ENX-FA0/FAH0 OUT selection indicator L/D indicator DPC indicator OUT indicator 7.8 ST indicator OUT indicator OUT selection indicator Threshold level (green, digital) 5. Incident level (white, digital) Mounted to DIN Track 40 (max. value with cover open) 5 (max. value with cover open) 04.8 (max. value with cover open) 4.5 Two,.4-dia. fiber unit holes.5 (6.5) (7).4 6 (9.9) 5.7 With Fiber Attachment (E9-F9) attached 0.5 (7.9) PFP-@N DIN Track (sold separately) 90.8 (9.) Optical communications 0

21 Accessories (Sold Separately) Wire-saving Connectors Master Connector EX-CN EX-CN Edge of Amplifier Unit (7), * * EX-CN: 4-dia. cable with conductors, Standard cable length: m (Conductor cross-section: 0. mm (AWG4), Insulator diameter:. mm) EX-CN: 4-dia. cable with 4 conductors, Standard cable length: m (Conductor cross-section: 0. mm (AWG4), Insulator diameter:. mm) Slave Connector EX-CN EX-CN Edge of Amplifier Unit (7), * * EX-CN:.6-dia. cable with conductor, Standard cable length: m (Conductor cross-section: 0. mm (AWG4), Insulator diameter:. mm) EX-CN: 4-dia. cable with conductors, Standard cable length: m (Conductor cross-section: 0. mm (AWG4), Insulator diameter:. mm) Sensor I/O Connectors Straight XSF-M4-40@-A L-shaped XSF-M4-40@-A

22 Mounting Bracket E9-L4 (0.) Mounting Holes Two, M holes dia. holes 7 6±0. 6 Four, Radius: max. 7.4 Material: Stainless steel (SUS04).4 DIN Track PFP-00N ±0.5 5±0. 7± (5)* 0 0,000 (500)* *Dimensions in parentheses are for the PFP-50N. Material: Aluminum PFP-00N ± ,000 Material: Aluminum End Plate PFP-M.5 50 M4 8 panhead screw 0 M4 spring washer Materials: Iron, zinc plating

23 OMR AUTOMATI AMERICAS HEADQUARTERS Chicago, IL USA OMR CANADA, INC. HEAD ICE Toronto,, Canada OMR ELECTRICS DE MEXICO HEAD ICE México DF OMR ELECTRICS DE MEXICO SALES ICE Apodaca, N.L OMR ARGENTINA SALES ICE Cono Sur OMR CHILE SALES ICE Santiago OTHER OMR LATIN AMERICA SALES OMR ELETRÔNICA DO BRASIL LTDA HEAD ICE São Paulo, SP, Brasil OMR EUROPE B.V. Wegalaan 67-69, NL- JD, Hoofddorp, The Netherlands. + (0) Authorized Distributor: Controllers & I/O Machine Automation Controllers (MAC) Motion Controllers Programmable Logic Controllers (PLC) Temperature Controllers Remote I/O Robotics Industrial Robots Mobile Robots Operator Interfaces Human Machine Interface (HMI) Motion & Drives Machine Automation Controllers (MAC) Motion Controllers Servo Systems Frequency Inverters Vision, Measurement & Identification Vision Sensors & Systems Measurement Sensors Auto Identification Systems Photoelectric Sensors Fiber-Optic Sensors Proximity Sensors Rotary Encoders Ultrasonic Sensors Safety Safety Light Curtains Safety Laser Scanners Programmable Safety Systems Safety Mats and Edges Safety Door Switches Emergency Stop Devices Safety Switches & Operator Controls Safety Monitoring/Force-guided Relays Control Components Power Supplies Timers Counters Programmable Relays Digital Panel Meters Monitoring Products Switches & Relays Limit Switches Pushbutton Switches Electromechanical Relays Solid State Relays Software Programming & Configuration Runtime E9I-E-0 Note: Specifications are subject to change. 08 Omron. All Rights Reserved. Printed in U.S.A. Printed on recycled paper.