Grain Elevator Safety
|
|
- Julianna Norman
- 5 years ago
- Views:
Transcription
1 Grain Elevator Safety Brad Freeman, CIH, CSP Gary Hulbert, CHMM, CSP Grain Elevator Overview Types and components of grain elevators OSHA standards Hazards associated with grain handling facilities: Engulfment Explosions/combustible dust Electrical hazards Entanglements 1
2 Grain Elevator Grain elevators typically consist of: Dump pit Leg Distributor Down spouts Bins Conveying system Parts of a grain elevator 2
3 Dumping grain into the dump pit Grain Leg with Down Spouts 3
4 Grain Leg -Bucket elevator Statistics Purdue s Agriculture Confined Space Incident Data Base Entrapment represents 80% of all cases 45% of entrapments had corn as the medium 20% are under the age of 21 4
5 Statistics 1,640 documented grain bin incidents 1,201 involved entrapment or engulfment with free flowing grain % of entrapment leads to death % entrapments lead to death Statistics 300,000 exempt grain handling facilities 70% of incidents occur on exempt facilities Falls from heights are on the increase since the 1990s Equipment entanglements are third leading incident 5
6 Agriculture Confined Space Injuries-2013 Purdue annual summary of grain related entrapment and engulfments 33 grain entrapment cases, 14 falls, and 12 equipment entanglements (including augers) Entrapments account for 49% of documented cases 4 Asphyxiation/poisoning OSHA Standard OSHA issued grain handling standard in 1987 Standard addresses walking on or underneath grain The hazards include: engulfment and entrapment 6
7 OSHA standards OSHA Standards Walking/working surfaces Guarding floor and wall openings and holes Storage of anhydrous ammonia Grain handling facilities Electrical Air contaminants OSHA Standard Standard covers: Hot work Entering bins Inside bucket elevator legs Preventative maintenance Housekeeping Emergencies and training 7
8 Grain Handling Engulfment More than 600 people have been engulfed and suffocated over past 40 years Purdue research indicates that 80% of cases resulted in fatalities Geographic Distribution of Grain Entrapments for
9 Engulfment in grain bin from: Standing on moving grain Bridging conditions Loosening grain on side of bins 9
10 Worker Entry into Grain Storage Bins Flowing Grain Buries Worker 2-3 seconds to react with auger running 4-5 seconds worker is trapped 22 seconds worker is covered Worker Entry into Grain Storage Bins Bridging Condition Bridging from unloading auger is off Auger starts grain falls Worker completely covered 10
11 Worker Entry into Grain Storage Bins Accumulation on Side of Bin Pile of grain on side Grain falls Worker suffocates Worker Entry into Grain Storage Bins Rescue During Bridging Person outside secured to bin Person on ground can go for help or assist in rescue 11
12 Pressure at each stage of engulfment Amount of time it takes to be engulfed in grain Rescue Equipment Available Grain rescue tube surrounds worker 12
13 Case Study - Engulfment Facility manager and worker enter bin when grain stops flowing Auger is left on After 5 minutes, manager exits bin leaving worker alone Worker becomes completely engulfed No one is aware that worker is still in bin 13
14 14
15 Hazard Prevention When workers enter storage bins: Turn off and lock out all powered equipment Prohibit walking down grain Provide all employees a body harness with a lifeline or a boatswains chair Hazard Prevention Provide an observer stationed outside the bin or issue entry permit Test the air within a bin or silo prior to entry If detected by testing, vent hazardous atmospheres 15
16 Combustible Dust - Hazard Prevention Written housekeeping program Identify "priority" housekeeping areas in within 35 feet of inside bucket elevators Dust accumulations in these priority housekeeping areas shall not exceed 1/8th inch Grain Dust Explosions 16
17 Westwego Louisiana Grain Elevator 17
18 Atchison Kansas-6 employees killed 2011 Combustible Dust To prevent dust explosions: Implement a PM program Minimize ignition sources through controlling hot work Install wiring and electrical equipment suitable for hazardous locations Design and properly locate dust collection systems to minimize explosion hazards Install an effective means of removing ferrous material from grain streams 18
19 Combustible Dust OSHA's grain handling standard requires that belts for bucket elevators purchased after March 30, 1988 are conductive and have a surface electrical resistance not exceeding 300 megohms Bucket elevators must have an opening to the head pulley section and boot section to allow for inspection, maintenance, and cleaning Combustible Dust Bearings must be mounted externally to the leg casing or the employer must provide vibration, temperature, or other monitoring of the conditions of the bearings if the bearings are mounted inside or partially inside the leg casing Bucket elevators must be equipped with a motion detection device which will shut-down the elevator when the belt speed is reduced by no more than 20% of the normal operating speed 19
20 Case Study Combustible Dust Explosion Tail pulley may have come off shaft Pulley struck concrete wall, creating sparks Mineral oil used to wet grain was not in use on day of explosion No alignment monitor for belt Insert photo 20
21 Grain Explosion Grain Explosion 21
22 Grain Explosion Electrical 22
23 Insert photo Floor Opening 23
24 Screw conveyors Machine Guarding Sweep augers Rotating parts of motors Belts and pulleys Screw Conveyor 24
25 Case Study Caught in Auger Top of auger approximately 3 feet above ground Cover had been removed from top of auger Worker attempted to step over auger Leg wrapped up in auger EMS can t remove worker 25
26 26
27 Sweep Auger A horizontal auger used to push grain remaining at the bottom of a storage bin Sweeps grain toward the bin's discharge sump opening The sweep rotates around the discharge opening to "sweep" the grain toward that opening The screw portion of an auger is often at least partially covered by some type of guard It is accurate to describe a sweep auger as an "unguarded... Auger Sweep Auger 27
28 Sweep Auger Sweep Auger Policy Follow permit requirements De-energized & LO/TO sweep and sub-floor augers before setting-up/digging-out Install and secure grates over sub-floor auger Sweep auger must be guarded as designed by manufacturer No walking on grain at depths presenting an engulfment hazard Rescue trained 28
29 Sweep Auger Policy Use engineering controls to prevent contact with auger (use of administrative controls alone is insufficient) Use speed control mechanism or bin stop device to prevent uncontrolled rotation of the sweep auger No hands, legs, or other similar means to manipulate an operating auger To adjust auger, it must be unplugged (w/ plug controlled by adjuster) or locked out Grain Vacuum 29
30 Grain Vacuum Grain Vacuum Hazards Dropping or releasing the nozzle on the grain surface can quickly pull the nozzle down into the grain and become buried In response, the operator may try to locate and lift the nozzle while the vacuum is running causing the grain to be sucked out from under them, burying him or her in seconds resulting in a fatality 30
31 Grain Vacuum Hazards Used on partially spoiled grain Vacuum operators are at risk of being engulfed due to bridging and grain collapse Grain vacuums should have emergency stopping device Operators need to follow manufacturer operating guidelines Conclusion Grain Bin Overview Statistics Standards that apply to commercial operations Hazard prevention Combustible dust Machine guarding Resources 31
32 Questions? Gary Hulbert, CHMM, CSP Phone number: Brad Freeman, CIH, CSP
Welcome to the Inaugural Grain Handling Safety Stand Down Engulfment Education and Prevention Seminar
Welcome to the Inaugural Grain Handling Safety Stand Down Engulfment Education and Prevention Seminar THANK YOU SPONSORS!! 2 Topics for Discussion Grain Engulfment History/Background. Types of engulfment
More informationHazardous Equipment Posters
Hazardous Equipment Posters Grain Augers and Hazards A grain auger is used to put grain into a grain bin or transport grain out of the bin to a truck or grain wagon to take to market. This grain auger
More informationCore EZ. Operating Manual. Toll Free B East Broadway Avenue Tampa, FL 33619
Operating Manual 3702 West Central Avenue Santa Ana, CA 92704 Toll Free 1-866-987-7297 11 High Street Suffield, CT 06078 www.ussaws.com 8004B East Broadway Avenue Tampa, FL 33619 Introduction This manual
More informationTools Hand and Power. OSHA Office of Training and Education 1
Tools Hand and Power 1 Hazards Workers using hand and power tools may be exposed to these hazards: objects that fall, fly, are abrasive, or splash harmful dusts, fumes, mists, vapors, and gases frayed
More informationCollege of Forestry 610: Power Tools
College of Forestry 610: Power Tools Safety Policy & Procedure Manual Section 600: Workshops and Shop Tools Effective: 01 January 2007 Revised: August 2014 PURPOSE The purpose of this section is to provide
More informationHAND AND POWER TOOLS
HAND AND POWER TOOLS Steingass Mechanical Contracting, Inc. 754 Progress Drive Medina, Ohio 44256 (330) 725-6090 HAND AND POWER TOOLS General All power tools whether furnished by Steingass Mechanical Contracting,
More informationTABLE OF CONTENTS DESCRIPTION. Safety Instructions Assembly Operation... 7
TABLE OF CONTENTS DESCRIPTION PAGE Warranty... 1 Safety Instructions... 2 Assembly... 3 Operation... 7 #360 Grain Cleaner Drawings... 8 #360 Grain Cleaner Parts List... 10 Utility Auger Option Drawing...
More informationVARIABLE SPEED WOOD LATHE
MODEL MC1100B VARIABLE SPEED WOOD LATHE INSTRUCTION MANUAL Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Version: 2015.02.02
More informationULTRA CUTTER MINI SAW
ULTRA CUTTER MINI SAW OPERATORS INSTRUCTION MANUAL Per OSHA 1926.503 it is the machine owner s responsibility to ensure that all workers using this Ultra Cutter Mini Saw are thoroughly trained in its use
More informationULTRA CUTTER PRO OPERATORS INSTRUCTION MANUAL. This manual covers all models 9, 11 and 13 HP
ULTRA CUTTER PRO OPERATORS INSTRUCTION MANUAL This manual covers all models 9, 11 and 13 HP Per OSHA 1926.503 it is the machine owner s responsibility to ensure that all workers using this Ultra Cutter
More informationSupport Stands & Conveyor Mountings. Parts, Assembly & Maintenance Manual. Steel Support Stand. Aluminum Support Stand Rev.
Support Stands & Conveyor Mountings Parts, Assembly & Maintenance Manual Aluminum Support Stand Steel Support Stand -00 Rev. B Table of Contents Safe Practices............................... Foreword....................................
More information3200 Series Modular Belt Straight Conveyors
00 Series Modular Belt Straight Conveyors Installation, Maintenance and Parts Manual Flat Modular Belt Conveyor Modular Belt Z-Frame Conveyor Available with: DORNER MFG. CORP. INSIDE THE USA OUTSIDE THE
More informationCONTENTS PRECAUTIONS BEFORE STARTING OPERATION PREPARATION FOR OPERATION CAUTIONS ON USE OPERATION
CONTENTS PRECAUTIONS BEFORE STARTING OPERATION ------------------------------------- 1 PREPARATION FOR OPERATION 1. Adjustment of needle bar stop position ---------------------------------------------------------
More informationIMCGS-2S series VIBRATING HOPPER INCLINED SCREW CONVEYOR OPERATING INSTRUCTION
IMCGS-2S series VIBRATING HOPPER INCLINED SCREW CONVEYOR OPERATING INSTRUCTION 1 1. Brief description IMCGS-2S series is an economical and convenient conveyor with rectangle, vibrating hopper. The characteristics
More informationC a r r i a g e A s s e m b l y R e p l a c e m e n t
E1 TF-CR C a r r i a g e A s s e m b l y R e p l a c e m e n t October 2007 Software Version 5.0 and higher IMPORTANT! TigerStop must be enabled with a code that must be obtained from TigerStop Customer
More informationMetric Support Stands & Conveyor Mountings. Parts, Assembly & Maintenance Manual. Aluminum Support Stand. Steel Support Stand
Metric Support Stands & Conveyor Mountings Parts, Assembly & Maintenance Manual 0 Aluminum Support Stand 0 Steel Support Stand 0 Fully Adjustable Aluminum Stand - Catalog DORSTM--ENG-.0 Table of Contents
More informationMODEL C-71-5 TWO-MAN EARTH DRILL
DO NOT THROW AWAY IMPORTANT MANUAL MODEL TWO-MAN EARTH DRILL Operator s Manual P.O.BOX 290 San Bernardino, CA. 92402 Phone (909) 478-5700 Fax (909) 478-5710 (800) 922-4680 E-mail: sales@groundhoginc.com
More informationEnvironmental Health and Safety Office Hazardous Dust Control Guide
Created February 2012 Table of Contents A. Purpose and Policy... Page 2 B. Introduction to Wood Dust...Page 2 C. Introduction to Combustible Dust.Page 3 D. House Keeping..Page 3 E. Other Hazards...Page
More informationSAFETY MANUAL All Models: On-Car Brake Lathes
SAFETY MANUAL All Models: On-Car Brake Lathes On-Car Brake Lathe SAFETY MANUAL phone: 800.543.6618 fax: 603.298.8404 email: info@procutusa.com web: www.procutusa.com INTRODUCTION Thank you for purchasing
More informationTABLE OF CONTENTS DESCRIPTION. Safety Instructions Assembly Operation... 7
TABLE OF CONTENTS DESCRIPTION PAGE Warranty... 1 Safety Instructions... 2 Assembly... 3 Operation... 7 #360 Grain Cleaner Drawings... 8 #360 Grain Cleaner Parts List... 10 Utility Auger Option Drawing...
More informationModel: SCD430 SCD640. Installation & Operation Guide P/N SCD640-95
Model: SCD430 SCD640 Installation & Operation Guide P/N SCD640-95 Model SCD430 and SCD640 Kurt has two Self-Centering vises, a four-inch jaw width (SCD430) and a six-inch jaw width (SCD640). Jaw opening
More informationMulti Tier Stands. Installation, Maintenance & Parts Manual
Installation, Maintenance & Parts Manual DORNER MFG. CORP. INSIDE THE USA OUTSIDE THE USA P.O. Box 0 975 Cottonwood Ave. TEL: -800-97-8664 TEL: 6-67-7600 Hartland, WI 509-000 USA FAX: -800-69-440 FAX:
More informationSAFETY DIRECTIVE 2.0 DEPARTMENTS AFFECTED. This Administrative Directive shall apply to all Town of Marana departments and employees.
SAFETY DIRECTIVE Title: Hand and Power Tools Issuing Department: Town Manager s Safety Office Effective Date: July 1, 2014 Approved: Gilbert Davidson, Town Manager Type of Action: New 1.0 PURPOSE This
More informationPortable Hand and Power Tools Self-Inspection Checklist
Optional Information Name of School: Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: Portable Hand and Power Tools Self-Inspection Checklist Guidelines: This checklist covers
More informationPORTABLE HALOGEN WORK LIGHT OWNER S MANUAL
PORTABLE HALOGEN WORK LIGHT OWNER S MANUAL L-9001 (29278) L-9002 (29276) WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules
More informationCircular Saw MODEL MT581. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH Circular Saw MODEL MT58 005337 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
More informationMotorized Tower Raising System Manual
Motorized Tower Raising System Manual Introduction and Safety Guidelines Important! Read through the manual in its entirety prior to assembly and installation of the motorized tower raising system. WARNING:
More informationUser Manual. Flooring Removal Machine (Patent Pending) Maintenance and Operating Instructions
User Manual Flooring Removal Machine (Patent Pending) Maintenance and Operating Instructions Copyright 2012 by Carpet Concepts LLC. All Rights Reserved. For technical questions or replacement parts please
More informationNorth Dakota State University Power Tool Operations and Maintenance
North Dakota State University Power Tool Operations and Maintenance I. Introduction This NDSU procedure provides guidelines for the use of power tools. The intent is to establish proper safety procedures
More informationInstallation information. METTLER TOLEDO MultiRange Floor/Pit scales DN-Line SPIDER-Line
Installation information METTLER TOLEDO MultiRange DN-Line SPIDER-Line DN / SPIDER Contents Page 1. Installation... 3 1.1 Preparatory work... 3 1.2 Equipotential bonding... 3 1.3 Floor installation...
More informationMAKER LAB Safety Instructions Power Tool Training
MAKER LAB Safety Instructions Power Tool Training Note: All the instructions from Basic Training apply to Power Tool Training. If you have not completed Basic Training, do so before you complete Power
More informationModel 20: Home & Garden Cart
Model 20: Home & Garden Cart Parts List Step 1: A: Install two ¾ Bolts (C) through the rear trim piece on the Bottom Panel (S) and attach to Lock Nuts. (Lock nuts on bottom side) B: Place left Side Panel
More information3-1/4 HP VARIABLE SPEED PLUNGE ROUTER
IMPORTANT INFORMATION 2-YEAR LIMITED WARRANTY FOR THIS PLUNGE ROUTER KING CANADA TOOLS OFFERS A 2-YEAR LIMITED WARANTY FOR NON-COMMERCIAL USE. 3-1/4 HP VARIABLE SPEED PLUNGE ROUTER PROOF OF PURCHASE Please
More informationGuild of Oregon Woodworkers Shop Safety Test
Guild of Oregon Woodworkers Shop Safety Test You must pass the Test with an 80% or better and self-correct it to 100% Make sure you put the answers under the correct portion of the answer sheet for the
More informationVictory Step OEM INSTALLATION MANUAL
Victory Step OEM INSTLLTION MNUL TLE OF CONTENTS Introduction 2 Safety 2 Resources Required 2 Installation 3 Step Deployment 4 Handrail Installation 5 djustment 6 Removal 6 Storage (If Installed) 7 Installation
More informationCan an Interlocked Guard take the Place of LockOut/TagOut?
Can an Interlocked Guard take the Place of LockOut/TagOut? Yes, if the Requirements of the Minor Servicing Exception are Met Jeffery H. Warren, PhD, PE, CSP A forge operator s right hand and arm had to
More informationEND MILL RE-SHARPENER EMG-413
END MILL RE-SHARPENER EMG-413 OPERATING INSTRUCTIONS -TABLE OF CONTENTS- A.SAFETY INSTRUCTIONS -------- 1 B.NAMES OF COMPONENTS ----- 2 C.OPERATIONS ------------------------ 3 D.REPLACING THE WHEEL --------
More informationEZ-SKIRT. Conveyor Skirting System. Installation and Users Manual. Manufactured by
EZ-SKIRT Conveyor Skirting System Installation and Users Manual Manufactured by Nelson Williams Linings, Inc. 8330 Jasmine Street PO Box 476 Mountain Iron, MN 55768 218-741-1080 May 2011 INTRODUCTION The
More informationGENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
More informationSAVE THIS FOR FUTURE REFERENCE THIS PRODUCT IS FOR PROFESSIONAL LABORATORY USE ONLY USER'S MANUAL
DENTAL, INC. TECHNICAL BULLETIN G801-022510 5860 FLYNN CREEK ROAD READ ALL INSTRUCTIONS P.O. BOX 106 BEFORE PROCEEDING COMPTCHE, CALIFORNIA, U.S.A. 95427-0106 SAVE THIS FOR FUTURE REFERENCE www.wellsdental.com
More informationMechatronics-Level 1
Measuring What Matters in Job Ready Assessment Blueprint Mechatronics-Level 1 Test Code: 2040 / Version: 01 Copyright 2012 General Assessment Information General Assessment Information Written Assessment
More informationSafety Instructions, Installation & Operator's Manual For. # CLAMSHELL GRASS CA TCHER KIT For 28" & 33" REAR ENGINE RIDING MOWERS
Safety Instructions, Installation & Operator's Manual For #6-3125 CLAMSHELL GRASS CA TCHER KIT For 28" & 33" REAR ENGINE RIDING MOWERS 28" REAR ENGINE RIDER WITH CLAMSHELL BAGGER KIT SHOWN SNAPPER, McDonough,
More informationPolicy Sponsor: Assistant Vice President Facilities Management. Responsible Unit: Trade Services
Safe Work Instructions for Powered Mitre Cut Hack Saw (Mitercut Model 220M) Policy Sponsor: Assistant Vice President Facilities Management Responsible Unit: Trade Services Approval Date: November 2016
More informationSeries 7 - Adjustable Height Tables
Page 1 of 22 Series 7 - Adjustable Height Tables Installation Instructions Tools required: #2 Phillips Bit with Extension #2 Square Drive Bit 4mm Hex Drive Bit Series 7 - Adjustable Height Tables Installation
More informationATBG280/6 Bench Grinder Bench Grinder ATBG280/6 230V-50Hz 280 Watt 150mm x 25mm Wheel size
Bench Grinder ATBG280/6 230V-50Hz 280 Watt 150mm x 25mm Wheel size SPECIFICATIONS Model Number : ATBG280/6 Nominal Voltage Power Consumption No load speed Wheel size Weight 230Volt 50Hz 280 Watts 2880
More informationAK30 Melter Operation Manual
AK30 Melter Operation Manual This article will help you show the importance of knowing how to operate the AK30 melter. Let s start by making your safety a priority. It is recommended that you wear eye
More informationRemoving and Replacing the Y-truck
Service Documentation Removing and Replacing the Y-truck To remove and replace the Y-truck you will need the following tools: 4mm Allen wrench 12mm stamped flat wrench #2 Phillips screwdriver (magnetic
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationMachine Guarding. OSHA Office of Training and Education 1
Machine Guarding OSHA Office of Training and Education 1 Introduction Crushed hands and arms, severed fingers, blindness - the list of possible machinery-related injuries is as long as it is horrifying.
More informationSeries 7 AdjusTable Height Tables
Series 7 AdjusTable Height Tables Tools required: #2 Phillips Bit with Extension #2 Square Drive Bit 4mm Hex Drive Bit #3 Phillips Bit If you have a problem, question, or request, call your local dealer,
More informationKeep this Operations manual with the Zip Rail at all times. New users are required to read it before installing and using the Zip Rail system.
TM Keep this Operations manual with the Zip Rail at all times. New users are required to read it before installing and using the Zip Rail system. It is the Zip Rail owner's duty to arrange that all workers
More informationElectric Skein Winder
Electric Skein Winder Assembly and Use Package Contents 1 - Triangular Body (w/ motor) 1 - Cross Arm 1 - Left Foot (w/ yarn guide) 1 - Right Foot 1 - Adjustable Finger (w/ yarn clip) 3 - Adjustable Fingers
More informationMODEL NO OWNER S MANUAL ASSEMBLY & OPERATING INSTRUCTIONS
COMPACT POST HOLE DIGGER MODEL NO. 24045000 OWNER S MANUAL ASSEMBLY & OPERATING INSTRUCTIONS THIS SAFETY ALERT SYMBOL IDENTIFIES IMPORTANT SAFETY MESSAGES IN THIS MANUAL. FAILURE TO FOLLOW THIS IMPORTANT
More informationaccidents which arise due to nonobservance and the safety information herein. SPECIFICATIONS
7 TON ELECTRIC LOG SPLITTER Model: 05620 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.
More informationVARIABLE SPEED WOOD LATHE. Model DB900 INSTRUCTION MANUAL
VARIABLE SPEED WOOD LATHE Model DB900 INSTRUCTION MANUAL 1007 TABLE OF CONTENTS SECTION...PAGE Technical data.. 1 General safety rules....1-3 Specific safety rules for wood lathe.....3 Electrical information.4
More informationBritish Columbia Institute of Technology WOOD DUST EXPOSURE CONTROL PLAN (JOINERY)
WOOD DUST EXPOSURE CONTROL PLAN (JOINERY) Contents 1. Purpose... 3 2. Roles & Responsibilities... 3 2.1 School... 3 2.2 Supervisor/Instructor... 3 2.3 Facilities Maintenance... 4 2.4 Housekeeping... 4
More informationOperating Manual 6 Industrial Bench Grinder ATBG280/
Operating Manual 6 Industrial Bench Grinder ATBG280/6 804531 40 Year Australian Heritage The reputable name in bench grinders for 40 years Protect yourself and others by observing all safety information,
More informationEXTRA TALL WALK-THROUGH GATE
OWNER S MANUAL MODEL: 0941, 0942 EXTRA TALL WALK-THROUGH GATE WITH SMALL PET DOOR! READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE. KEEP INSTRUCTIONS FOR FUTURE USE. www.carlsonpetproducts.com Carlson
More informationWestern Illinois University Department of Art Woodshop Orientation
Western Illinois University Department of Art Woodshop Orientation SAFETY is the first priority woodworking tools are inherently dangerous. Machines turn sharp saw blades and cutters at high speeds. Accidents
More informationOPERATOR S MANUAL WARNING. Read and become familiar with this manual BEFORE operating unit.
OPERATOR S MANUAL For Models 350 & 210 Model 350 Model 210 WARNING Read and become familiar with this manual BEFORE operating unit. Before operating this equipment, thoroughly read this set of instructions,
More informationABM International, Inc. Navigator Assembly Manual
ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor
More informationUltraFeed Feeder Operator s Manual
UltraFeed Feeder Operator s Manual Version 1.1 Table of Contents Topic Page Safety Statement and Recommendations 3 General Operation and Set-Up 5 Control Panel Operation 6 Set Up and Operation 7 Set Up
More informationGrain Tank Cross Auger Trough Liner for John Deere 9400 / 9500 Combine
www.polyskid.com P. O. Drawer 349, Monticello, GA. 31064 Phone: 800-542-7659, Fax: 706-468-2881 E-Mail: polytech@polyskid.com Grain Tank Cross Auger Trough Liner for John Deere 9400 / 9500 Combine FOR
More informationBritish Columbia Institute of Technology WOOD DUST EXPOSURE CONTROL PLAN (CARPENTRY)
WOOD DUST EXPOSURE CONTROL PLAN (CARPENTRY) Contents 1. Purpose... 3 2. Roles & Responsibilities... 3 2.1 Supervisor/Instructor... 3 2.2 Chief Instructor... 3 2.3 Facilities Maintenance... 4 2.4 Housekeeping...
More informationIN-BED FRAME MOUNT INSTALLATION INSTRUCTIONS
Lit. No. 13666, Rev. 05 December 5, 2005 IN-BED FRAME MOUNT INSTALLATION INSTRUCTIONS FOR SINGLE-STAGE AND TWO-STAGE TAILGATE SPREADERS Read Owner's Manual before operating or servicing spreader. Empty
More informationRemoving the Z-Axis lead screw
Page 1 of 8 TITLE: Sabre Z-Axis Lead Screw Replacement Procedure Gerber FastFact #: 5048 Supplied by: Gerber Hardware Support Last Modified: June 14, 2007 Summary: Tools used: The following procedure explains
More informationFitWork Walkstation Series 7 AdjusTables
FitWork Walkstation Tools Required: #2 Phillips Bit with Extension Page 1 of 20 A7TG660606H A7TR663232H FitWork Walkstation 4mm Hex Head Bit A7TG660632H A7TR383030H www.details-worktools.com A7TG663206H
More informationFSS020-ADVANCED DIPLOMA IN FIRE & INDUSTRIAL SAFETY MANAGEMENT ONE YEAR EXAMINATION NOVEMBER TIME: 3 Hours Marks: 100
1 BHARAT SEVAK SAMAJ NATIONAL DEVELOPMENT AGENCY, PROMOTED BY GOVERNMENT OF INDIA CENTRAL BOARD OF EXAMINATIONS BSS NATIONAL VOCATIONAL EDUCATION MISSION FSS020-ADVANCED DIPLOMA IN FIRE & INDUSTRIAL SAFETY
More informationSCREW JACKS Operating Instructions
INS114EN.5 SCREW JACKS Operating Instructions Sweden Int +46 372 265 00 info@swedrive.se Vat.no SE556145631901 138-4551 1 Table of Contents 1. Health and Safety... 3 1.1. Notice about safety... 3 1.2.
More informationAuto Feed Screwdriver
ENGLISH Auto Feed Screwdriver MODEL 6833 MODEL 6834 MODEL 6836 002607 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE
More informationWESTERN ILLINOIS UNIVERSITY DEPARTMENT OF ART
WESTERN ILLINOIS UNIVERSITY DEPARTMENT OF ART WOODSHOP ORIENTATION SAFETY is the first priority woodworking tools are inherently dangerous. Machines turn sharp saw blades and cutters at high speeds. Accidents
More informationService Manual for XLE/XLT Series Laser Engravers
Service Manual for XLE/XLT Series Laser Engravers Table of Contents Maintenance...1 Beam alignment...3 Auto focus alignment...8 Bridge alignment...10 Electronics panel replacement...11 X motor change...12
More informationFirst published : May 1997 Fourth edition : January No
First published : May 1997 Fourth edition : January 2006 No. 050153 INTRODUCTION Thank you for your purchasing Kansai Special's FX Series. Read and study this instruction manual carefully before beginning
More informationSeries Adjustable Height Tables
Series 7.2 - Adjustable Height Tables Tools required: Power Drill #2 SQUARE DRIVE BIT If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522)
More informationUsage and Assembly Instructions
Instructions #1037447 Product #795234 Revision D Usage and Assembly Instructions Rear Fork (Buttstock) Rear Fork Lock Knob Rail Lock Knob Front Fork (Forend) Rails Tilt Friction Knob Rail Extension Locks
More informationCEILING-MOUNTED MONORAIL ANCHOR TRACK SYSTEM Assembly and Operation Instruction Manual
CEILING-MOUNTED MONORAIL ANCHOR TRACK SYSTEM Assembly and Operation Instruction Manual This manual is for various mounting types and plain and trussed track profiles. ISO 9001:2008 Registered Manual 103-0075
More informationOPERATOR S MANUAL Model 58B Prefeed / Dereeler
110 Fairgrounds Drive P.O. Box 188 Manlius, NY 13104-0188 USA 315.682.9176 FAX: 315.682.9160 OPERATOR S MANUAL Model 58B Prefeed / Dereeler PRODUCTION WIRE PROCESSING EQUIPMENT Website: www.carpentermfg.com
More informationQuality Screw Conveyor Systems and Components CATALOG NUMBER 991A
Quality Screw Conveyor Systems and Components CATALOG NUMBER 991A Quality Screw Conveyor Systems and Components Are E C A B E H F D H G Please refer to Screw Conveyor Corporation Engineering Manual and
More informationOPERATION & MAINTENANCE MANUAL
OPERATION & MAINTENANCE MANUAL AUTOMATIC PECAN CRACKER Food Processing Equipment and Machinery Specializing in the Pecan Industry Mailing: PO Box 817, Mansfield, Louisiana 71052 Located: 280 Independence
More informationSubpart O - Machine Guarding
Subpart O - Machine Guarding We Will Cover: Machine Guarding Principles Subpart O - Highlights Mock Plant Walk-Through Why are machines not guarded? No one would stick their arm, hand, finger, head, etc.
More informationCopyright 2007 ES Manufacturing, Inc th Street North St. Petersburg, FL 33713
e-mail sales@esmfg.com US/Canada 800-55ES-MFG Documentation & Warranty Packet MB110 ( 600 rpm s) Thank you for purchasing the MB110 If properly operated and maintained, this Heavy Duty Fiber Cutter will
More information2015 NFPA 70E. SESHA 2015 ARIZONA MINI CONFERENCE December 10, 2015 Intel Corporation
2015 NFPA 70E SESHA 2015 ARIZONA MINI CONFERENCE December 10, 2015 Intel Corporation Introduction Jeffrey A. Pugh, P.E. Pugh Engineering LLC Bachelor of Science Degrees in Electrical Engineering and Computer
More informationAssembly Instructions. Important!
Play Action Spiral Tube Slide Assembly Instructions Important! Intended for residential use by children ages 2 to 10, only on properly installed PlayStar playsets. Before use refer to complete safety guidelines
More informationFLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Trailer system.
More informationINSTRUCTION. Industrial Sewing Machines V7100/D,DE,F,ML W8100/D,DE,F,C W8042 W V7002-1S W8103-1S. No Third edition : March 2001
INSTRUCTION Industrial Sewing Machines V7100/D,DE,F,ML W8100/D,DE,F,C W8042 W8042-1 V7002-1S W8103-1S Third edition : March 2001 No. 010012 INTRODUCTION Thank you for your purchasing Kansai Special's V.W
More informationHydraulic Clamp Carrier. Installation & Operation Manual
Hydraulic Clamp Carrier Installation & Operation Manual Hydraulic Clamp Carrier Installation & Operation Manual Quick Machinery Company 8272 Peninsula Drive Kelseyville, CA 95451 phone: (707) 272-6719
More informationWoodworking Machinery- Other than Saws Self-Inspection Checklist
Optional Information Name of School: Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: Woodworking Machinery- Other than Saws Self-Inspection Checklist Guidelines: This checklist
More informationJEWEL, SAPPHIRE, STAR and NOVA Turntables
sotaturntables@kwom.com - www.sotaturntables.com JEWEL, SAPPHIRE, STAR and NOVA Turntables PLEASE READ THE INSTRUCTIONS COMPLETELY BEFORE BEGINNING SET UP AND OPERATION! UNPACKING The SOTA turntable comes
More information12mm (Max) 6mm (Max) 82mm (Max) 12mm (Max) 6mm (Max)
1 1 2 2 3 3 82mm (Max) 12mm (Max) 12mm (Max) 6mm (Max) 4 4 5 6 8 6mm (Max) 0.5 0mm 1 5 6 7 7 8 9 9 A = B 10 11 12 D B 1 13 14 15 0 C A D E 16 17 18 F G D B N H J G I K 19 A 20 G L 21 C K 1mm L M 1mm 22
More informationSection Nine Rig/Platform Environment. Oil & Gas Training. Oil & Gas Training. Oil & Gas Training. Rig/Platform Environment
Section Nine /Platform Environment /Platform Environment The rig site are broken into basic work areas. These are: Substructure /Platform Environment The rig site are broken into basic work areas. These
More informationMODEL 83 Pail Handler
MORSE MFG. CO., INC. 727 West Manlius Street P.O. Box 518 East Syracuse, NY 13057-0518 Phone: 315-437-8475 Fax: 315-437-1029 Email: service@morsemfgco.com Website: www.morsemfgco.com COPYRIGHT 2005 MORSE
More informationN. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Dump Body tarping system. With tarping systems
More informationENGLISH (Original instructions) INSTRUCTION MANUAL. Drill DS4012 DOUBLE INSULATION. IMPORTANT: Read Before Using.
ENGLISH (Original instructions) INSTRUCTION MANUAL Drill DS402 05402 DOUBLE INSULATION IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model DS402 Capacities Steel 3 mm Wood
More informationAngle Grinder MODEL 9553B MODEL 9555B
ENGLISH Angle Grinder MODEL 9553B MODEL 9555B 006649 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR
More informationSAFETY AND OPERATING MANUAL
SAFETY AND OPERATING MANUAL 2 General Power Tool Safety Warnings WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire
More informationNibbler MODEL JN1601. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH Nibbler MODEL JN60 00477 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. SPECIFICATIONS
More information6 BLADE CUTTER MODEL # PCC-6 OPERATION MANUAL
4511 WAYNE AVENUE PHILADELPHIA PA 19144 TEL: 888-800-2663 FAX: 800-582-9643 6 BLADE CUTTER MODEL # PCC-6 OPERATION MANUAL CONTENTS I. INTRODUCTION TO BOND PCC-6 / MACHINE SPECIFICATIONS II. SAFETY PRECAUTIONS
More informationMI MI OPERATING MANUAL
MODEL NO.: MI-76100 MI-76150 OPERATING MANUAL RULES for SAFE OPERATION MAGNUM INDUSTRIAL MI-76100 and MI 76150 DRILL PRESSES To help ensure safe operation, please take a moment to learn the how to operate
More informationLumber Smith. Assembly Manual. If you are having problems assembling the saw and need assistance, please contact us at:
Lumber Smith Assembly Manual If you are having problems assembling the saw and need assistance, please contact us at: 804-577-7398 info@lumbersmith.com 1 Step 1 Safety Carefully read the Owners Manual.
More informationDrill INSTRUCTION MANUAL. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE 1 REFERENCE.
ENGLISH (Original instructions) INSTRUCTION MANUAL Drill 6411 6412 6413 007894 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE
More information