Electronic Circuits. Power Amplifiers. Manar Mohaisen Office: F208 Department of EECE
|
|
- Beverly Chandler
- 5 years ago
- Views:
Transcription
1 Electronic Circuits Power Amplifiers Manar Mohaisen Office: F208 Department of EECE
2 Review of the Precedent Lecture Explain the Amplifier Operation Explain the BJT AC Models Introduce the Common-emitter Amplifier Introduce the Common-Collector Amplifier Introduce the Common-Base Amplifier Introduce Multistage Amplifiers
3 Class Objectives Explain the Operation Class A Power Amplifier Explain the Operation of Class B and AB Amplifiers Explain the Operation of Class C Amplifier
4 The Class A Power Amplifier Operation Biased amplifier is always operating in the linear region. Power amplifier provides power rather than voltage to a load. The output signal is an amplified replica of the input signal. Categories Small-signal Amplifier The ac signal moves over a small percentage of the total ac load line. Large-signal Amplifier The output ac signal approaches the limits of the ac load line.
5 The Class A Power Amplifier contd. Heat Dissipation Power devices must dissipate a large amount of internally generated heart. The collector terminal is the critical junction. Therefore, heat sink is usually connected to the collector.
6 The Class A Power Amplifier contd. Centered Q-Point AC and DC load lines intersect at the Q-point. When the Q-point is at the center of the ac load line A maximum class A signal can be obtained.
7 The Class A Power Amplifier contd. Non-centered Q-point Q-point closer to cutoff Q-point closer to saturation
8 The Class A Power Amplifier contd. Power Gain The ratio of the input power to the (load) output power. A p P = P P L is the power delivered to the load. P in is the input power delivered to the amplifier. L in Other formulas of the power gain P L Therefore, V = R A p 2 L L P in V = R V R R = = V 2 in in 2 L in A2 in 2 v R R in L L
9 DC Quiescent Power The power dissipation with no input signal. Output Power The Class A Power Amplifier contd. The maximum ac unclipped signal occurs for centered Q-point. Therefore, (the peak for Common-Emitter Amplifier) The maximum peak current swing is [peak value] Then, P = I V DQ CQ CEQ V = I R c(max) CQ c V Ic(max) = R CEQ P = I V out(max) crms ( ) crms ( ) c = (0.707 I )(0.707 V ) = 0.5I V c c CQ CEQ
10 Example 7-1 The Class A Power Amplifier contd. V I B R = 10 12V = 1.82 V 2 V R R CC V 0.7 = B = E R + R E1 E2 1.78mA R = R R β ( R + r ) ' in( tot)1 1 2 ac( Q1) E1 e( Q1) A = 56k Ω 10k Ω 200(68Ω+ 14 Ω ) = 8.4 kω = A A = ( 27.9)(1) = 27.9 vtot ( ) v1 v2 r' eq ( 1) A = 25 mv = 14 Ω I E R R R R = = = 27.9 c1 C 3 4 v1 r' + R r' + R eq ( 1) E1 eq ( 1) E1 A p R = A = ( 27.9) = 817,330 2 in( tot) k Ω vtot ( ) R L 8Ω
11 Efficiency The Class A Power Amplifier contd. The ratio of the output signal power supplied to a load to the total power from the DC supply. Average power supply current, I CC, equals I CQ. The supply voltage is at least 2V CEQ. Therefore, the total DC power is The maximum efficiency In Practice, P = I V = 2I V DC CC CC CQ CEQ P 0.5I V out CQ CEQ η max = = = 0.25 P 2I V DC CQ CEQ The efficiency of Class A Amplifiers is less than 10% (low efficiency). Therefore, their use is limited for small power applications (less than 1 W)
12 Operation of Class B Power Amplifier It is biased at cutoff. It operates in the linear region for 180 o. The Class B and Class AB Amplifiers Operation of Class AB Power Amplifier It operates slightly more than 180 o.
13 The Class B and Class AB Amplifiers contd. Advantages of Class B and Class AB over Class A They are more efficient than a class A amplifier. You can obtain more output power for a given input power. Disadvantage of Class B and Class AB It is difficult to implement the linear circuit.
14 Class B Operation The Q-point is at cutoff. The Class B and Class AB Amplifiers contd. I CQ = 0 and V CEQ = V CE(cutoff). It is brought into the linear region of operation When the input signal drives the transistor into operation.
15 The Class B and Class AB Amplifiers contd. Class B Push-Pull Operation Two class B amplifiers are used to amplify the entire cycle. There are two approaches to for using push-pull amplifiers Transformer coupling Two complementary symmetry transistors (npn/pnp BJTs)
16 Transformer Coupling Q1 conducts on the positive half cycle Q2 will be then in cutoff. Q2 conducts on the negative half cycle Q1 will be then in cutoff. The Class B and Class AB Amplifiers contd.
17 Complementary Symmetry Transistors The DC base voltage = 0 The input signal biases the transistors. Q1 conducts during the positive half cycle Q2 conducts during the negative half cycle. The Class B and Class AB Amplifiers contd.
18 Crossover Distortion Transistors are off for the range ]-V BE, V BE [ The Class B and Class AB Amplifiers contd.
19 The Class B and Class AB Amplifiers contd. Biasing the Push-Pull Amplifier for Class AB Operation The transistors are conducting even without the input signal. The collector current is given by I CQ V = CC 0.7 R 1
20 AC Operation Q1: AC cutoff at VCC with V 0.7 I = CC CQ R The AC saturation current V I = CC csat ( ) R The Class B and Class AB Amplifiers contd. 1 L
21 The Class B and Class AB Amplifiers contd. AC Load Line for Q1.
22 The Class B and Class AB Amplifiers contd. Efficiency When there is no signal, transistors have a very small current. The power dissipation is small. Therefore, the efficiency is higher than that of class A amplifiers. Example 7-3 The ideal maximum out voltage V out(peak) = V CC = 20 V The maximum peak current I 20 I CC = = out( peak) c( sat) RL 150 V 133mA
23 Single Supply Push-Pull Amplifier The Class B and Class AB Amplifiers contd. V V V CC out( peak) CEQ 2 I VCEQ V = I = = R 2R out( peak) c( sat) L CC L
24 Maximum Output Power The Class B and Class AB Amplifiers contd. P = I V out out( rms) out( rms) I = 0.707I = 0.707I out( rms) out( peak) c( sat) P = 0.5I V out csat ( ) CC VCEQ = VCC /2 V = V = V out( rms) out( peak) CEQ P = I V DC CC CC Each transistor working on half cycle, then: I P CC DC = = I I csat ( ) π V π csat ( ) CC η max P 0.25I V out csat ( ) CC = = = 0.25π = 0.79 P I V / π DC csat ( ) CC
25 Input Resistance The Class B and Class AB Amplifiers contd. R = β r + R R R in ' ac( e ) E 1 2
26 Darlington Class AB Amplifier When the load is relatively small, Darlington pair is used The input resistance is increased The Class B and Class AB Amplifiers contd. R = β r + R R R in ' ac( e ) L 1 2 = β β ( r + R ) R R ' ac1 ac2 e L 1 2
27 The Class C Amplifier Operation Conduction occurs for much less than 180 o. More efficient than either class A and class B/AB It is biased below cutoff with a negative V BB supply.
28 The Class C Amplifier contd.
29 The Class C Amplifier contd. Operation more The input peak exceeds V BB + V BE for conduction. For entire ac load line operation I c is ideally I c(sat) and V ce is V ce(sat).
30 The Class C Amplifier contd. Power Dissipation Maximum Power dissipation (during the on period) P = I V D( on) c( sat) ce( sat) The average power dissipation over the period T P = t T P on D( avg) D( on)
31 The Class C Amplifier contd. Tuned Operation The output is not a replica of the output, Therefore, a resistive load is of no value in liner applications. A parallel resonant circuit is thus used. The resonant frequency f r = 1 2π LC
32 The Class C Amplifier contd. Operation Transistor on Capacitor charges Transistor off Capacitor discharges Inductor charges Capacitor charges in opposite direction. Capacitor discharges. Inductor charges Capacitor charges. Transistor on Due to input pulse.
33 The Class C Amplifier contd. Operation If The transistor remains off However, due to the input signal, I c turns on and off i.e., transistor is on periodically. As a result, the output voltage does decay to zero. The Class C Amplifier As a Frequency Multiplier f r = 1 = 2 f 2π LC in
34 The Class C Amplifier contd. Efficiency The output voltage has a peak of approximately (2V CC ), therefore 2 (0.707 V ) 2 P Vrms CC out = = R R Rc is the equivalent parallel resistance of the collector tank circuit. Has a low value. The (Total) Input Power Therefore, the efficiency is T c P = P + P out η = out = T out D( avg) P P P P + P Therefore, efficiency is close to 1 (100 %) for P out >> P D(avg)! out c D( avg) P = I V P D( on) c( sat) ce( sat) = t T P on D( avg) D( on)
35 The Class C Amplifier contd. Example 7-8 V CC = 24 V, Rc = 100 Ω, P D(avg) = 4 mw P out = (0.707 V ) 2 V R = R = 2 rms c CC c 2.88 W Pout P η = = out = 2.88W 1 P P + P 2.88W + 4 mw T out D( avg)
36 The Class C Amplifier contd. Clamper Bias Conduction happens for a short time.
37 The Class C Amplifier contd. Example 7-9 V = (1.414)(1V) = 1.4 V s( p) The base is clamped at ( 0.7) = 0.7 V dc V s ( p ) The signal at the base has A negative peak of V s ( 0.7) V ( p + = = ) A positive peak of +0.7 V Output Voltage V 2 1 pp = V = V fr = = 411kHz CC 2π LC
38 Discussion & Notes K K A K A A A A K K K K A K A K K A K A K A
Electronic Devices. Floyd. Chapter 7. Ninth Edition. Electronic Devices, 9th edition Thomas L. Floyd
Electronic Devices Ninth Edition Floyd Chapter 7 Power Amplifiers A power amplifier is a large signal amplifier that produces a replica of the input signal on its output. In the case shown here, the output
More informationLecture (10) Power Amplifiers (2)
Lecture (10) Power Amplifiers (2) By: Dr. Ahmed ElShafee ١ Class B/AB Power the ideal maximum peak output current for both dual supply and single supply push pull amplifiers is approximately Ic(sat), and
More informationChapter 12 Power Amplifier
Chapter 12 Power Amplifier Definitions In small-signal amplifiers the main factors are: Amplification Linearity Gain Since large-signal, or power, amplifiers handle relatively large voltage signals and
More informationLecture 8 Power Amplifier (Class A)
Lecture 8 Power Amplifier (Class A) nduction of Power Amplifier Power and Efficiency Amplifier Classification Basic Class A Amplifier Transformer Coupled Class A Amplifier Ref:08037HKN EE3110 Power Amplifier
More informationCrystal Oscillator. Circuit symbol
Crystal Oscillator Crystal Oscillator Piezoelectric crystal (quartz) Operates as a resonant circuit Shows great stability in oscillation frequency Piezoelectric effect : When mechanical stress is applied
More informationSIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR (AUTONOMOUS) Siddharth Nagar, Narayanavanam Road QUESTION BANK
SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR (AUTONOMOUS) Siddharth Nagar, Narayanavanam Road 517583 QUESTION BANK Subject with Code : Electronic Circuit Analysis (16EC407) Year & Sem: II-B.Tech & II-Sem
More informationLABORATORY MODULE. Analog Electronics. Semester 2 (2005/2006)
LABORATORY MODULE ENT 162 Analog Electronics Semester 2 (2005/2006) EXPERIMENT 5 : The Class A Common-Emitter Power Amplifier Name Matrix No. : : PUSAT PENGAJIAN KEJURUTERAAN MEKATRONIK KOLEJ UNIVERSITI
More informationChapter 6: Power Amplifiers
Chapter 6: Power Amplifiers Contents Class A Class B Class C Power Amplifiers Class A, B and C amplifiers are used in transmitters Tuned with a band width wide enough to pass all information sidebands
More informationChapter 6. BJT Amplifiers
Basic Electronic Devices and Circuits EE 111 Electrical Engineering Majmaah University 2 nd Semester 1432/1433 H Chapter 6 BJT Amplifiers 1 Introduction The things you learned about biasing a transistor
More informationCommunication Circuit Lab Manual
German Jordanian University School of Electrical Engineering and IT Department of Electrical and Communication Engineering Communication Circuit Lab Manual Experiment 2 Tuned Amplifier Eng. Anas Alashqar
More informationCode No: R Set No. 1
Code No: R059210404 Set No. 1 II B.Tech I Semester Supplimentary Examinations, February 2008 ELECTRONIC CIRCUIT ANALYSIS ( Common to Electronics & Communication Engineering and Electronics & Telematics)
More informationLecture #9 Tuned Amplifiers
December 2014 Ahmad El-Banna Integrated Technical Education Cluster At AlAmeeria J-601-1448 Electronic Principals Lecture #9 Tuned Amplifiers Instructor: Dr. Ahmad El-Banna Agenda Class C vs. Tuned Amplifier
More informationSmall signal Amplifier stages. Figure 5.2 Classification of power amplifiers
5.1 Introduction When the power requirement to drive the load is in terms of several Watts rather than mili-watts the power amplifiers are used. Power amplifiers form the last stage of multistage amplifiers.
More informationDC Bias. Graphical Analysis. Script
Course: B.Sc. Applied Physical Science (Computer Science) Year & Sem.: Ist Year, Sem - IInd Subject: Electronics Paper No.: V Paper Title: Analog Circuits Lecture No.: 3 Lecture Title: Analog Circuits
More informationCode: 9A Answer any FIVE questions All questions carry equal marks *****
II B. Tech II Semester (R09) Regular & Supplementary Examinations, April/May 2012 ELECTRONIC CIRCUIT ANALYSIS (Common to EIE, E. Con. E & ECE) Time: 3 hours Max Marks: 70 Answer any FIVE questions All
More informationDiode and Bipolar Transistor Circuits
Diode and Bipolar Transistor Circuits 2 2.1 A Brief Review of Semiconductors Semiconductors are crystalline structures in which each atom shares its valance electrons with the neighboring atoms. The simple
More informationElectronic Devices. Floyd. Chapter 6. Ninth Edition. Electronic Devices, 9th edition Thomas L. Floyd
Electronic Devices Ninth Edition Floyd Chapter 6 Agenda BJT AC Analysis Linear Amplifier AC Load Line Transistor AC Model Common Emitter Amplifier Common Collector Amplifier Common Base Amplifier Special
More informationMicroelectronics Circuit Analysis and Design. Interdigitated BJT: Top and Cross-Sectional Views. Power Amps 10/11/2013. In this chapter, we will:
Microelectronics Circuit Analysis and Design Donald A. Neamen Chapter 8 Output Stages and Power Amplifiers In this chapter, we will: Describe the characteristics of BJT and MOSFET power transistors Define
More informationINSTITUTE OF AERONAUTICAL ENGINEERING (AUTONOMUS) Dundigal, Hyderabad
INSTITUTE OF AERONAUTICAL ENGINEERING (AUTONOMUS) Dundigal, Hyderabad - 00 0 ELECTRONICS AND COMMUNICATION ENGINEERING ASSIGNMENT Name : ELECTRONIC CIRCUIT ANALYSIS Code : A0 Class : II - B. Tech nd semester
More informationWhen you have completed this exercise, you will be able to determine the ac operating characteristics of
When you have completed this exercise, you will be able to determine the ac operating characteristics of multimeter and an oscilloscope. A sine wave generator connected between the transistor and ground
More informationSo far we have dealt with only small-signal ampliers. In small-signal ampliers the main factors were amplication linearity gain
Contents Power Amplier Types Class A Operation Class B Operation Class AB Operation Class C Operation Class D Operation Amplier Eciency Series-Fed Class A Amplier AC-DC Load Lines Maximum Eciency Figure
More informationOutput Stage and Power Amplifiers
Microelectronic Circuits Output Stage and ower Amplifiers Slide 1 ntroduction Most of the challenging requirement in the design of the output stage is ower delivery to the load. ower consumption at the
More informationITT Technical Institute. ET215 Devices 1. Unit 6 Chapter 3, Sections
ITT Technical Institute ET215 Devices 1 Unit 6 Chapter 3, Sections 3.7-3.9 Chapter 3 Section 3.7 The Bipolar Transistor as a Switch Objectives: Explain how a transistor can be used as a switch 1. Compute
More informationPower Amplifiers. Class B Class AB
ower Amplifiers Class B Class AB Class B he circuit each transistor conducts for a half of every signal period complementary pair push-pull arrangement peration vi ( 0.6; 0.6) (off), (off) v 0 vi v 0.6
More informationOutput Stages and Power Amplifiers
CHAPTER 11 Output Stages and Power Amplifiers Introduction 11.7 Power BJTs 911 11.1 Classification of Output Stages 11. Class A Output Stage 913 11.3 Class B Output Stage 918 11.4 Class AB Output Stage
More informationUNIT 1 MULTI STAGE AMPLIFIES
UNIT 1 MULTI STAGE AMPLIFIES 1. a) Derive the equation for the overall voltage gain of a multistage amplifier in terms of the individual voltage gains. b) what are the multi-stage amplifiers? 2. Describe
More informationLinear electronic. Lecture No. 1
1 Lecture No. 1 2 3 4 5 Lecture No. 2 6 7 8 9 10 11 Lecture No. 3 12 13 14 Lecture No. 4 Example: find Frequency response analysis for the circuit shown in figure below. Where R S =4kR B1 =8kR B2 =4k R
More information2. SINGLE STAGE BIPOLAR JUNCTION TRANSISTOR (BJT) AMPLIFIERS
2. SINGLE STAGE BIPOLAR JUNCTION TRANSISTOR (BJT) AMPLIFIERS I. Objectives and Contents The goal of this experiment is to become familiar with BJT as an amplifier and to evaluate the basic configurations
More informationTutorial 2 BJTs, Transistor Bias Circuits, BJT Amplifiers FETs and FETs Amplifiers. Part 1: BJTs, Transistor Bias Circuits and BJT Amplifiers
Tutorial 2 BJTs, Transistor Bias Circuits, BJT Amplifiers FETs and FETs Amplifiers Part 1: BJTs, Transistor Bias Circuits and BJT Amplifiers 1. Explain the purpose of a thin, lightly doped base region.
More informationBJT Amplifier Power Amp Overview(H.21)
BJT Amplifier Power Amp Overview(H.21) 20170616-2 Copyright (c) 2016-2017 Young W. Lim. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation
More informationLecture (01) Transistor operating point & DC Load line
Lecture (01) Transistor operating point & DC Load line By: Dr. Ahmed ElShafee ١ BJT Characteristic Collector Characteristic Curves B C E ٢ BJT modes of operation Conditions in Cutoff Conditions in Saturation
More informationChapter 11 Output Stages
1 Chapter 11 Output Stages Learning Objectives 2 1) The classification of amplifier output stages 2) Analysis and design of a variety of output-stage types 3) Overview of power amplifiers Introduction
More informationPartIIILectures. Multistage Amplifiers
University of missan Electronic II, Second year 2015-2016 PartIIILectures Assistant Lecture: 1 Multistage and Compound Amplifiers Basic Definitions: 1- Gain of Multistage Amplifier: Fig.(1-1) A general
More informationBJT Circuits (MCQs of Moderate Complexity)
BJT Circuits (MCQs of Moderate Complexity) 1. The current ib through base of a silicon npn transistor is 1+0.1 cos (1000πt) ma. At 300K, the rπ in the small signal model of the transistor is i b B C r
More informationExercise 2: AC Voltage and Power Gains
Exercise 2: AC Voltage and Power Gains an oscilloscope. Signals of equal magnitude but opposite polarity are needed for each transistor (Q1 and Q2). Center-tapped input transformer T1 is used as a phase
More informationExercise 2: AC Voltage and Power Gains
Exercise 2: AC Voltage and Power Gains When you have completed this exercise, you will be able to determine voltage and power gains by using oscilloscope. The ac operation schematic for the COMPLEMENTARY
More informationBipolar Junction Transistors
Bipolar Junction Transistors Invented in 1948 at Bell Telephone laboratories Bipolar junction transistor (BJT) - one of the major three terminal devices Three terminal devices more useful than two terminal
More information55:041 Electronic Circuits
55:041 Electronic Circuits Output Stages and Power Amplifiers Sections of Chapter 8 A. Kruger Power + Output Stages1 Power Amplifiers, Power FETS & BJTs Audio (stereo) MP3 Players Motor controllers Servo
More informationBIPOLAR JUNCTION TRANSISTORS (BJTs) Dr Derek Molloy, DCU
IPOLAR JUNCTION TRANSISTORS (JTs) Dr Derek Molloy, DCU What are JTs? Two PN junctions joined together is a JT Simply known as a transistor! ipolar? Current carried by electrons and holes Will see FETs
More informationET215 Devices I Unit 4A
ITT Technical Institute ET215 Devices I Unit 4A Chapter 3, Section 3.1-3.2 This unit is divided into two parts; Unit 4A and Unit 4B Chapter 3 Section 3.1 Structure of Bipolar Junction Transistors The basic
More informationThe shape of the waveform will be the same, but its level is shifted either upward or downward. The values of the resistor R and capacitor C affect
Diode as Clamper A clamping circuit is used to place either the positive or negative peak of a signal at a desired level. The dc component is simply added or subtracted to/from the input signal. The clamper
More informationECE 334: Electronic Circuits Lecture 2: BJT Large Signal Model
Faculty of Engineering ECE 334: Electronic Circuits Lecture 2: BJT Large Signal Model Agenda I & V Notations BJT Devices & Symbols BJT Large Signal Model 2 I, V Notations (1) It is critical to understand
More information55:041 Electronic Circuits
55:041 Electronic Circuits Output Stages and Power Amplifiers Sections of Chapter 8 A. Kruger Power + Output Stages1 Power Amplifiers, Power FETS & BJTs Audio (stereo) MP3 Players Motor controllers Servo
More informationRadio Frequency Electronics
Radio Frequency Electronics Tuned Amplifiers John Battiscombe Gunn Born in 1928 in Egypt (father was a famous Egyptologist), and was Educated in England Worked at IBM s Thomas J. Watson Research Center
More informationElectronic Troubleshooting
Electronic Troubleshooting Chapter 3 Bipolar Transistors Most devices still require some individual (discrete) transistors Used to customize operations Interface to external devices Understanding their
More informationIFB270 Advanced Electronic Circuits
IFB270 Advanced Electronic Circuits Chapter 11: Thyristors Prof. Manar Mohaisen Department of EEC Engineering Review of the Precedent Lecture To introduce several concepts on capacitance in amplifiers
More informationI C I E =I B = I C 1 V BE 0.7 V
Guide to NPN Amplifier Analysis Jason Woytowich 1. Transistor characteristics A BJT has three operating modes cutoff, active, and saturation. For applications, like amplifiers, where linear characteristics
More informationTransistors and Applications
Chapter 17 Transistors and Applications DC Operation of Bipolar Junction Transistors (BJTs) The bipolar junction transistor (BJT) is constructed with three doped semiconductor regions separated by two
More informationHomework Assignment 12
Homework Assignment 12 Question 1 Shown the is Bode plot of the magnitude of the gain transfer function of a constant GBP amplifier. By how much will the amplifier delay a sine wave with the following
More informationSubject Code: Model Answer Page No: / N
Important Instructions to examiners: 1) The answers should be examined by key words and not as word-to-word as given in the model answer scheme. 2) The model answer and the answer written by candidate
More informationPHYS225 Lecture 6. Electronic Circuits
PHYS225 Lecture 6 Electronic Circuits Transistors History Basic physics of operation Ebers-Moll model Small signal equivalent Last lecture Introduction to Transistors A transistor is a device with three
More informationElectronic Circuits EE359A
Electronic Circuits EE359A Bruce McNair B206 bmcnair@stevens.edu 201-216-5549 Lecture 18 488 Class C operation 4 2 h( t) 0 2 4 0 0.2 0.4 0.6 0.8 t 0 ( ) 20 log A j 20 40 60 0 10 20 30 Cconduction_angle
More informationChapter 3: Bipolar Junction Transistors
Chapter 3: Bipolar Junction Transistors Transistor Construction There are two types of transistors: pnp npn pnp The terminals are labeled: E - Emitter B - Base C - Collector npn 2 Transistor Operation
More informationEE105 Fall 2015 Microelectronic Devices and Circuits
EE105 Fall 2015 Microelectronic Devices and Circuits Prof. Ming C. Wu wu@eecs.berkeley.edu 511 Sutardja Dai Hall (SDH) 11-1 Transistor Operating Mode in Amplifiers Transistors are biased in flat part of
More informationExperiment #8: Designing and Measuring a Common-Collector Amplifier
SCHOOL OF ENGINEERING AND APPLIED SCIENCE DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING ECE 2115: ENGINEERING ELECTRONICS LABORATORY Experiment #8: Designing and Measuring a Common-Collector Amplifier
More informationLab 4. Transistor as an amplifier, part 2
Lab 4 Transistor as an amplifier, part 2 INTRODUCTION We continue the bi-polar transistor experiments begun in the preceding experiment. In the common emitter amplifier experiment, you will learn techniques
More informationHomework Assignment 10
Homework Assignment 10 Question 1 (Short Takes) Two points each unless otherwise indicated. 1. What is the 3-dB bandwidth of the amplifier shown below if r π = 2.5K, r o = 100K, g m = 40 ms, and C L =
More informationTHE HONG KONG POLYTECHNIC UNIVERSITY EN107/1 Department of Electronic and Information Engineering. EN107: OCL Class AB Power Amplifier Objective
THE HONG KONG POLYTECHNIC UNIVERSITY EN107/1 EN107: OCL Class AB Power Amplifier Objective 1. To study the circuit performance of an OCL amplifier. 2. To study the effects of biasing on cross-over distortion
More informationDesigning an Audio Amplifier Using a Class B Push-Pull Output Stage
Designing an Audio Amplifier Using a Class B Push-Pull Output Stage Angel Zhang Electrical Engineering The Cooper Union for the Advancement of Science and Art Manhattan, NY Jeffrey Shih Electrical Engineering
More informationII/IV B. TECH. DEGREE EXAMINATIONS, NOVEMBER Second Semester EC/EE ELECTRONIC CIRCUIT ANALYSIS. Time : Three Hours Max.
Total No. of Questions : 9] [Total No. of Pages : 02 B.Tech. II/ IV YEAR DEGREE EXAMINATION, APRIL/MAY - 2014 (Second Semester) EC/EE/EI Electronic Circuit Analysis Time : 03 Hours Maximum Marks : 70 Q1)
More informationEC1203: ELECTRONICS CIRCUITS-I UNIT-I TRANSISTOR BIASING PART-A
SHRI ANGALAMMAN COLLEGE OF ENGG & TECH., TRICHY 621105 (Approved by AICTE, New Delhi and Affiliated to Anna University Chennai/Trichy) ( ISO 9001:2008 Certified Institution) DEPARTMENT OF ELECTRONICS &
More informationPage 1 of 7. Power_AmpFal17 11/7/ :14
ECE 3274 Power Amplifier Project (Push Pull) Richard Cooper 1. Objective This project will introduce two common power amplifier topologies, and also illustrate the difference between a Class-B and a Class-AB
More informationWeek 12: Output Stages, Frequency Response
ELE 2110A Electronic Circuits Week 12: Output Stages, Frequency esponse (2 hours only) Lecture 12-1 Output Stages Topics to cover Amplifier Frequency esponse eading Assignment: Chap 15.3, 16.1 of Jaeger
More informationChapter.8: Oscillators
Chapter.8: Oscillators Objectives: To understand The basic operation of an Oscillator the working of low frequency oscillators RC phase shift oscillator Wien bridge Oscillator the working of tuned oscillator
More informationModule 4 Unit 4 Feedback in Amplifiers
Module 4 Unit 4 Feedback in mplifiers eview Questions:. What are the drawbacks in a electronic circuit not using proper feedback? 2. What is positive feedback? Positive feedback is avoided in amplifier
More informationFeedback and Oscillator Circuits
Chapter 14 Chapter 14 Feedback and Oscillator Circuits Feedback Concepts The effects of negative feedback on an amplifier: Disadvantage Lower gain Advantages Higher input impedance More stable gain Improved
More informationECE:3410 Electronic Circuits
ECE:3410 Electronic Circuits Output Stages and Power Amplifiers Sections of Chapter 8 A. Kruger Power + Output Stages1 Power Amplifiers, Power FETS & BJTs Audio (stereo) MP3 Players Motor controllers Servo
More informationPower Amplifiers. Class A Amplifier
Power Amplifiers The Power amplifiers amplify the power level of the signal. This amplification is done in the last stage in audio applications. The applications related to radio frequencies employ radio
More informationIFB270 Advanced Electronic Circuits
IFB270 Advanced Electronic Circuits Chapter 9: FET amplifiers and switching circuits Prof. Manar Mohaisen Department of EEC Engineering Review of the Precedent Lecture Review of basic electronic devices
More informationChapter 5 Transistor Bias Circuits
Chapter 5 Transistor Bias Circuits Objectives Discuss the concept of dc biasing of a transistor for linear operation Analyze voltage-divider bias, base bias, and collector-feedback bias circuits. Basic
More informationLecture #3 ( 2 weeks) Transistors
Spring 2015 Benha University Faculty of Engineering at Shoubra ECE-291 Electronic Engineering Lecture #3 ( 2 weeks) Transistors Instructor: Dr. Ahmad El-Banna 1 Agenda BJT Structure Basic Operation Transistor
More informationElectronic Circuits EE359A
Electronic Circuits EE359A Bruce McNair B206 bmcnair@stevens.edu 201-216-5549 Lecture 20 496 Power BJTs Collector currents in the multi-ampere range Multi-watt power dissipation Achieved by: High temperature
More informationR a) Draw and explain VI characteristics of Si & Ge diode. (8M) b) Explain the operation of SCR & its characteristics (8M)
SET - 1 1. a) Define i) transient capacitance ii) Diffusion capacitance (4M) b) Explain Fermi level in intrinsic and extrinsic semiconductor (4M) c) Derive the expression for ripple factor of Half wave
More informationPhysics 116A Fall 2000: Final Exam
Physics 6A Fall 2000: Final Exam 2//2000 (rev. 2/0) Closed book and notes except for three 8.5 in 2 sheets of paper. Show reasoning for full credit. There are 6 problems and 200 points. Note: complex quantities
More information10. SINGLE-SUPPLY PUSH-PULL AMPLIFIER
0. SNGE-SUY USH-U AMFE The push-pull amplifier circuit as discussed in section-9 requires a dual power supply. t can be tailored to operate on a single supply as illustrated in Figure 0.. n this case the
More informationPhysics 116A Notes Fall 2004
Physics 116A Notes Fall 2004 David E. Pellett Draft v.0.9 beta Notes Copyright 2004 David E. Pellett unless stated otherwise. References: Text for course: Fundamentals of Electrical Engineering, second
More informationDocument Name: Electronic Circuits Lab. Facebook: Twitter:
Document Name: Electronic Circuits Lab www.vidyathiplus.in Facebook: www.facebook.com/vidyarthiplus Twitter: www.twitter.com/vidyarthiplus Copyright 2011-2015 Vidyarthiplus.in (VP Group) Page 1 CIRCUIT
More informationEXPERIMENT 10: SINGLE-TRANSISTOR AMPLIFIERS 11/11/10
EXPERIMENT 10: SINGLE-TRANSISTOR AMPLIFIERS 11/11/10 In this experiment we will measure the characteristics of the standard common emitter amplifier. We will use the 2N3904 npn transistor. If you have
More informationLinear IC s and applications
Questions and Solutions PART-A Unit-1 INTRODUCTION TO OP-AMPS 1. Explain data acquisition system Jan13 DATA ACQUISITION SYSYTEM BLOCK DIAGRAM: Input stage Intermediate stage Level shifting stage Output
More information(a) BJT-OPERATING MODES & CONFIGURATIONS
(a) BJT-OPERATING MODES & CONFIGURATIONS 1. The leakage current I CBO flows in (a) The emitter, base and collector leads (b) The emitter and base leads. (c) The emitter and collector leads. (d) The base
More informationOscillators. An oscillator may be described as a source of alternating voltage. It is different than amplifier.
Oscillators An oscillator may be described as a source of alternating voltage. It is different than amplifier. An amplifier delivers an output signal whose waveform corresponds to the input signal but
More informationDEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING III SEMESTER EC 6304 ELECTRONIC CIRCUITS I. (Regulations 2013)
DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING III SEMESTER EC 6304 ELECTRONIC CIRCUITS I (Regulations 2013 UNIT-1 Part A 1. What is a Q-point? [N/D 16] The operating point also known as quiescent
More informationEC202- ELECTRONIC CIRCUITS II Unit- I -FEEEDBACK AMPLIFIER
EC202- ELECTRONIC CIRCUITS II Unit- I -FEEEDBACK AMPLIFIER 1. What is feedback? What are the types of feedback? 2. Define positive feedback. What are its merits and demerits? 3. Define negative feedback.
More informationThe collector terminal is common to the input and output signals and is connected to the dc power supply. Common Collector Circuit
Common Collector Circuit When you have completed this exercise, you will be able to determine the dc operating conditions of a common collector (CC) transistor circuit by using a typical CC circuit. You
More informationIFB270 Advanced Electronic Circuits
IFB270 Advanced Electronic Circuits Chapter 14: Special-purpose op-amp circuits Prof. Manar Mohaisen Department of EEC Engineering eview of the Precedent Lecture Introduce the level detection op-amp circuits
More informationBy: Dr. Ahmed ElShafee
Lecture (02) Transistor operating point & DC Load line (2), Transistor Bias Circuit 1 By: Dr. Ahmed ElShafee ١ DC Load Line The dc operation can be described graphically using a dc load line. This is a
More informationElectronics EECE2412 Spring 2017 Exam #2
Electronics EECE2412 Spring 2017 Exam #2 Prof. Charles A. DiMarzio Department of Electrical and Computer Engineering Northeastern University 30 March 2017 File:12198/exams/exam2 Name: : General Rules:
More informationCode No: Y0221/R07 Set No. 1 I B.Tech Supplementary Examinations, Apr/May 2013 BASIC ELECTRONIC DEVICES AND CIRCUITS (Electrical & Electronics Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions
More information... Second Semester
كنا نظنك اي عيل تركتنا... لكن طيفك مل يزل يغشانا مثل الندى يسقي النبات بقطره... قد ابت ليال يف ادلىج عطشاان ما زلت أذكر حني أدخل معمال... متسك هجازا للقياس تحاكه... فأ راك جتلس هادئا حيرانا تكتب وترمس
More informationMC34063A 1.5 A, Step-Up/Down/Inverting Switching Regulators
- + MC34063A MC34063A 1.5 A, Step-Up/Down/Inverting Switching Regulators DESCRIPTION The MC34063A Series is a monolithic control circuit containing the primary functions required for DC to DC converters.
More informationConcepts to be Covered
Introductory Medical Device Prototyping Analog Circuits Part 2 Semiconductors, http://saliterman.umn.edu/ Department of Biomedical Engineering, University of Minnesota Concepts to be Covered Semiconductors
More informationTransistor Configuration
Transistor Configuration 1 Objectives To review BJT biasing circuit. To study BJT amplifier circuit To understand the BJT configuration. To analyse single-stage BJT amplifier circuits. To study the differential
More informationELECTRONIC CIRCUITS LAB
ELECTRONIC CIRCUITS LAB 1 2 STATE INSTITUTE OF TECHNICAL TEACHERS TRAINING AND RESEARCH GENERAL INSTRUCTIONS Rough record and Fair record are needed to record the experiments conducted in the laboratory.
More informationExperiment 8&9 BJT AMPLIFIER
Experiment 8&9 BJT AMPLIFIER 1 BJT AS AMPLIFIER 1. Objectiv e: 1- To demonstrate the operation and characteristics of small signals common emitter amplifiers. 2- What do we mean by a linear amplifier and
More informationMicroelectronics Circuit Analysis and Design
Neamen Microelectronics Chapter 6-1 Microelectronics Circuit Analysis and Design Donald A. Neamen Chapter 6 Basic BJT Amplifiers Neamen Microelectronics Chapter 6-2 In this chapter, we will: Understand
More informationTUNED AMPLIFIERS 5.1 Introduction: Coil Losses:
TUNED AMPLIFIERS 5.1 Introduction: To amplify the selective range of frequencies, the resistive load R C is replaced by a tuned circuit. The tuned circuit is capable of amplifying a signal over a narrow
More informationImproving Amplifier Voltage Gain
15.1 Multistage ac-coupled Amplifiers 1077 TABLE 15.3 Three-Stage Amplifier Summary HAND ANALYSIS SPICE RESULTS Voltage gain 998 1010 Input signal range 92.7 V Input resistance 1 M 1M Output resistance
More informationLARGE SIGNAL AMPLIFIERS
LARGE SIGNAL AMPLIFIERS One method used to distinguish the electrical characteristics of different types of amplifiers is by class, and as such amplifiers are classified according to their circuit configuration
More informationChapter 13 Output Stages and Power Amplifiers
Chapter 13 Output Stages and Power Amplifiers 13.1 General Considerations 13.2 Emitter Follower as Power Amplifier 13.3 Push-Pull Stage 13.4 Improved Push-Pull Stage 13.5 Large-Signal Considerations 13.6
More information5.25Chapter V Problem Set
5.25Chapter V Problem Set P5.1 Analyze the circuits in Fig. P5.1 and determine the base, collector, and emitter currents of the BJTs as well as the voltages at the base, collector, and emitter terminals.
More information