Crystal Oscillator of the C500 and C166 Microcontroller Families
|
|
- Irene Gilbert
- 6 years ago
- Views:
Transcription
1 Microcontrollers ApNote AP Crystal Oscillator of the C500 and C166 Microcontroller Families The microcontrollers of the C500/C166 Family include the active part of the oscillator. This document explains the quartz crystal oscillator functionality and gives recommendations how to get the right composition on external circuits. Author : Peter Mariutti / HL DC AT Munich Semiconductor Group 04.98, Rel. 03
2 Contents Page 1 Introduction Oscillator-Inverter Oscillator Inverter Type_A, Type_B and Type_C Oscillator Inverter Type_R Oscillator Inverter Type_LP1 and Type_LP Fundamental Mode and 3rd Overtone Oscillator Start-up Time Definition of the Oscillator Start-up Time tst_up Definition of the Oscillator Off Time toff Drive Level Measurement Method of Drive Current Drive Level Calculation for Fundamental Mode Drive Level Calculation for 3rd Overtone Mode Start-up- and Oscillation Reliability Measurement Method of Start-up- and Oscillation Reliability Safety Factor Trouble Shooting Pull down Resistor RX Feedback Resistor Rf Qualification of the Results Oscillator Circuitry Layout Recommendations Avoidance of Capacitive Coupling Ground Connection of the Crystal Package Avoidance of Parallel Tracks of High Frequency Signals Ground Supply Correct Module Placement Layout Recommendation Recommendations of the Crystal Manufacturer Tele Quarz Group Used Short Cuts General Information using the Appendix Appendix C500 Family C500 Family: Relation between Oscillator-Inverter Type and Device Type C500 Family: Type_A Oscillator-Inverter C500 Family: Type_B Oscillator-Inverter C500 Family: Type_C Oscillator-Inverter Semiconductor Group 2 of 38 AP
3 12 Appendix C166 Family C166 Family: Relation between Oscillator-Inverter Type and Device Type C166 Family: Type_R Oscillator-Inverter C166 Family: Type_R Oscillator-Inverter Fundamental Mode C166 Family: Type_R Oscillator-Inverter 3rd Overtone Mode C166 Family: Type_LP1 Oscillator-Inverter C166 Family: Type_LP2 Oscillator-Inverter C166 Family: Type_RTC1 Oscillator-Inverter Quartz Crystals for the C500 and C166 Family Fundamental Mode Quartz Crystal for Standard Temperature Range Fundamental Mode Quartz Crystal for Advanced Temperature Range rd Overtone Mode Quartz Crystal for Standard Temperature Range rd Overtone Mode Quartz Crystal for Advanced Temperature Range Real Time Clock Quartz Crystal TELE QUARZ GROUP Sales Offices Semiconductor Group 3 of 38 AP
4 AP ApNote - Revision History Actual Revision : Previous Revision : Page of actual Rev. Page of prev.rel. Subjects (changes since last release) 5 4 New oscillator types added Chapter trouble shooting added Note added New short cuts added Extended appendix is a trademark of TELE QUARZ GROUP Semiconductor Group 4 of 38 AP
5 1 Introduction This Application Note provides recommendations concerning the selection of quartz crystals and circuit composition for each oscillator. The cooperation between the IC oscillator and the quartz crystal is not always working properly because of a wrong composition on external circuits. Therefore Siemens (HL DC AT) and Tele Quarz Group built up a cooperation to support our customers with the appropriate knowledge to guarantee a problem-free operation of the oscillator. 2 Oscillator-Inverter The microcontrollers of the C500/C166 Family include the active part of the oscillator (also called oscillator-inverter). Based on the history and evolution of the microcontrollers there are different oscillator-inverters implemented at the C500/C166 Family members. Due to the same reason, the meaning of XTAL1 and XTAL2 pins is different. In this Application Note and at the C166 family, XTAL1 is the oscillator-inverter input while XTAL2 is the output. At the C500 family it is recommended to have a closer look at the Data Sheet of each device. The on-chip oscillator-inverter can either run with an external crystal and appropriate external oscillator circuitry (also called oscillator circuitry or passive part of the oscillator), or it can be driven by an external oscillator. The external oscillator directly connected to XTAL1, leaving XTAL2 open, feeds the external clock signal to the internal clock circuitry. The oscillator input XTAL1 and output XTAL2 connect the internal CMOS Pierce oscillator to the external crystal. The oscillator provides an inverter and a feedback element. The resistance of the feedback element is in the range of 0.5 to 1 MΩ. Depending on the type of oscillator-inverter the gain can be different between reset active and reset inactive. The recommendations in the appendix are seperated to the different oscillator-inverter types of the C500 and C166 family. 2.1 Oscillator Inverter Type_A, Type_B and Type_C These types of inverters are implemented in C500 family derivatives. The gain of these types of oscillator-inverters is the same during reset active and reset inactive. These oscillators are optimized for operating frequencies in the range of 2.0 (3.5) to 20 MHz. For details reffer to appendix. 2.2 Oscillator Inverter Type_R This type of inverter is implemented in most of the current C166 family derivatives. The gain of the Type_R oscillator-inverter is high during reset is active and is Reduced by one-third when reset is inactive. This feature provides an excellent start-up behaviour and a reduced supply current for the oscillator during normal operation mode. The Type_R oscillator-inverter is optimized for an operating frequency range of 3.5 to 40 MHz. Semiconductor Group 5 of 38 AP
6 2.3 Oscillator Inverter Type_LP1 and Type_LP2 This type of inverter is a Low Power oscillator, version 1 and version 2. Inverter Type_LP2 is the actual version and will be implemented in new derivatives of the C16x family. The Type_LP oscillator-inverter is a high sophisticated module with a high gain but low power consumption. The gain of the Type_LP oscillator-inverter is the same during reset active and reset inactive. This oscillator is optimized for an operating frequency range of 3.5 to 16 MHz. For input frequencies above MHz provided by an external oscillator the oscillator s output should be terminated with a 15 pf capacitance and a 3 kω resistor in series to XTAL2. 3 Fundamental Mode and 3rd Overtone Depending on the system demands there are two different kind of oscillator modes available. The external quartz crystal can be prepared for fundamental mode or 3rd overtone mode. The standard external oscillator circuitry for fundamental mode (see figure 1) includes the crystal, two low end capacitors and a series resistor R X2 to limit the current through the crystal. The series resistor R X2 is not often used in C500 family devices. A test resistor R Q may be temporarily inserted to measure the oscillation allowance of the oscillator circuitry. How to check the start-up reliability will be explained in detail in Chapter 6. For the 3rd overtone mode an additional inductance/capacitance combination (L X /C X2 ) is required to suppress oscillation in the fundamental mode and bias voltage (C X ) at the XTAL2 output. Fundamental mode is suppressed via phase shift and filter characteristics of the L X /C X2 network. The formula f LXCX2 in chapter 5.3 calculates the frequency at which the inductive behaviour of the L X /C X2 network changes to capacitive. The oscillation condition in 3rd overtone mode needs a capacitive behaviour for f 3rd and an inductive one for f fund. 3rd overtone mode is often used in applications where the crystal has to be resistant against strong mechanical vibrations because 3rd overtone crystals have a higher mechanical stability than fundamental mode crystals with the same frequency. In general, there are different possibilities to connect the L X /C X network for 3rd overtone to the oscillator circuit. The L X /C X network theoretically can be connected to C X1 or C X2. This Application Note recommends the connection to C X2 (see figure 1) because a little variation of L X caused by production deviation has more influence concerning the oscillator start-up behaviour at the XTAL1 input than at the XTAL2 output. Furthermore, the additional hardware for 3rd overtone mode receives additional electrical noise from the system. In a C X1 /L X /C X combination the noise will be amplified via the oscillator inverter. In a C X2 /L X /C X combination the noise will be damped by the quartz crystal. Depending on the quality of the Printed Circuit Board design, a C X1 /L X /C X combination can have a bad influence on the start-up behaviour of the oscillator. Note: There is no need of changing existing working designs which use the C X1 /L X /C X combination when the safety factor SF is within the desired range. Semiconductor Group 6 of 38 AP
7 Fundamental Mode: ( MHz) 3rd Overtone Mode: ( MHz) to internal clock circuitry to internal clock circuitry XTAL1 XTAL2 (XTAL2) (XTAL1) XTAL1 XTAL2 (XTAL2) (XTAL1) Q R Q R X2 Q R Q R X2 L X C X1 C X2 C X1 C X2 C X GND GND Figure 1 Oscillator Modes Note: The operating frequency of the oscillator depends on the type of oscillator-inverter and the oscillation mode. For detailed information refer to appendix. Semiconductor Group 7 of 38 AP
8 4 Oscillator Start-up Time Based on small electrical system noise or thermic noise caused by resistors, the oscillation starts with a very small amplitude. Due to the amplification of the oscillator-inverter, the oscillation amplitude increases and reaches its maximum after a certain time period t st_up (start-up time). Typical values of the start-up time are within the range of 0.1 msec t st_up 5 msec. Theoretically the oscillator-inverter performs a phase shift of 180, and the external circuitry performs a phase shift of 180 to fulfill the oscillation condition of an oscillator. A total phase shift of 360 is necessary. In reality, the real phase shift of the oscillator-inverter depends on the oscillator frequency and is approximately in the range of 100 to 210. It is necessary to compose the external components in a way that a total phase shift of 360 is performed. This can be achieved by a variation of C x1 and C x2. Note: The external hardware reset signal has to be active for a longer time period than the oscillator start-up time in order to prevent undefined effects. Note: Because of the different gain of the Type_R oscillator-inverter during reset active and reset inactive it is recommended to consider the oscillation in both phases of the reset signal. 4.1 Definition of the Oscillator Start-up Time t st_up The definition of the oscillator start-up time is not a well defined value in literature. Generally it depends on the power supply rise time dvcc/dt at power on, on the electrical system noise and on the oscillation amplitude. For this application the oscillator start-up time t st_up is defined from Vcc/2 to 0.9*V OSC_max of the stable oscillation, see figure 2. Supply Voltage at XTAL2 Output V CC V CC /2 0.9*V OSC_max Signal at XTAL2 Output V OSC_max t t st_up Figure 2 Oscillator Start-up Time Semiconductor Group 8 of 38 AP
9 4.2 Definition of the Oscillator Off Time t off Measurement of the oscillator start-up time is normally done periodically. After switching off power supply, the oscillation continues until the whole reactive power oscillating between inductance and capacitance is consumed. Therefore the time between switching off and on (t off ) the power supply must not be too short in order to get reproduceable results. t off depends on the composition of the oscillator components. It is recommended to use a oscillation off time t off 0.5 sec, see figure 3. V CC t t off t off Figure 3 Oscillator Off Time Semiconductor Group 9 of 38 AP
10 5 Drive Level 5.1 Measurement Method of Drive Current The amplitude of mechanical vibration of the quartz crystal increases proportionally to the amplitude of the applied current. The power dissipated in the load resonance resistance R L (in other technical descriptions also called effective resistance or transformed series resistance ) is given by the drive level P W. The peak to peak drive current I pp is measured in the original application with a current probe directly at the crystal lead, see figure 4. The drive level is calculated with the formulas shown in chapters 5.2 and 5.3. The drive level is mainly controlled via R X2 and C X1, but C X2 also has an influence. XTAL1 XTAL2 (XTAL2) (XTAL1) I pp Current Probe R X2 Q R Q (3rd Overtone) C X1 C X2 L X C X GND Figure 4 Measurement Method of Drive Current with a Current Probe Semiconductor Group 10 of 38 AP
11 5.2 Drive Level Calculation for Fundamental Mode The maximum and minimum allowed drive level depends on the used crystal and should be within the typical range of 50 µw P W 800 µw. For detailed information, the quartz crystal data sheet has to be regarded. The load resonance resistance R Ltyp is calculated with the typical values of the quartz crystal and of the system. The formula is shown below. The typical values of R 1 (R 1typ ) and C 0 (C 0typ ) are supplied by the crystal manufacturer. The stray capacitance C S consists of the capacitance of the board layout, the input capacitance of the on-chip oscillator-inverter and other parasitic effects in the oscillator circuit. A typical value of the input pin capacitance of the inverter is 2 pf. The maximum value is 10 pf. Drive level: 2 P W = I Q R Ltyp Drive Current: I Q = Ipp (for sine wave) Load Resonance Resistance: C0typ R Ltyp = R1typ C L 2 Load Capacitance: C CX1 L = ( CX1 + CX2) C S Note: The drive level calculation in systems with a Type_R oscillator-inverter should be done with the drive current (I Q ) measured during reset is inactive. Using an optimized external circuitry the difference of I Q during reset active and reset inactive is very small. Semiconductor Group 11 of 38 AP
12 5.3 Drive Level Calculation for 3rd Overtone Mode The calculation of the drive level in 3rd overtone mode is equal to fundamental mode besides the calculation of the load capacitance. The formulas below show the relations between load capacitance, circuit components and frequencies in 3rd overtone. Load Capacitance: C CX1 CX2rest L = C CX1 + C S X2rest C X2 rest Capacitance: CX2rest = 1 CX ( 2πf3rd) 2 LX Resonance Frequency of C X2 and L X (Thomson Formula): 1 f LXCX2 = π LX CX2 Relation between f fund and f 3rd : f f fund + f 3rd LXCX = 2 f 2 fund Semiconductor Group 12 of 38 AP
13 6 Start-up- and Oscillation Reliability Most problems concerning the oscillator in a microcontroller system occur during the oscillation start-up time. During start-up time the drive level of the oscillation is very small and is increased up to the maximum. During that time the resistance of the crystal can reach very high values because crystals show resistance dips depending on the drive level. This effect is called drive level dependence (DLD). The DLD of a quartz crystal depends on the quality and can alter during production and during the life time of the crystal. If the resistance dips of the crystal increase in a range where the amplification of the oscillator is lower than one, than the oscillation cannot start. Therefore it is strongly recommended to check the start-up and oscillation reliability. 6.1 Measurement Method of Start-up- and Oscillation Reliability As already mentioned before, the resistance of a crystal depends on the drive level. A simple method to check the start-up and oscillation reliability of the oscillator is to insert a test resistor R Q in series into the quartz crystal, see figure 4. The basic timing of Vcc during testing is equal to the described timing for testing the oscillation startup time (see chapter oscillation start-up time ). The value of R Q is increased until the oscillation does not start any more. From the state of no oscillation R Q is then decreased until oscillation starts again. Using a Type_R oscillator-inverter this procedure has to be considered during reset active and reset inactive. This final value of R Qmax is used for further calculations of the safety factor SF. Note: The series resistor R Q should be an SMD device or a potentiometer which is suitable for RF (Radio Frequency). Depending on the RF behaviour of the potentiometer, the results between using an SMD resistor or a potentiometer can be different. The result of the potentiometer is sometimes worse than the one of the SMD resistor. It is therefore recommended to use the potentiometer in order to find the final value R Qmax and to perform a verification of R Qmax with a SMD resistor. Note: The start-up and oscillation reliability can be also influenced by using a socket for the microcontroller during measurement. The influence is caused by the additional inductance and capacitance of the socket. Depending on the demands to the final system which is used for mass production the consideration of start-up and oscillation reliability has to be done with or without a socket. The recommendations in the appendix are verified without socket. Note: Depending on the system demands the verification of the start-up and oscillation reliability should be also done for variation of supply voltage and temperature. Semiconductor Group 13 of 38 AP
14 Table 1 Element Range for Test Element Range C X1 = C X pf R X kω 3rd Overtone: L X 1-15µH 3rd Overtone: C X 1-10nF The described measurement procedure for R Qmax has to be performed for different values of R X2, C X1 and C X2. During the test, the values of the different elements have to be changed one after another, and the results are noted in a table. A proposal for a protocol table is shown in table 2. For the first test it is recommended to use C X1 = C X2. A suggestion for the range is given in table 1. The range of the elements depends on the used quartz crystal and on the characteristics of the printed circuit board. After the test the measured values should be displayed in a diagram, see figure 6. The measurement method of start-up and oscillation reliability for 3rd overtone mode needs more efforts than for fundamental mode. The relation between the values of L X and C X2 is given via the formulas in chapter 5.3. When C X lies within the recommended range it has theoretically no effect on the start-up behaviour of the oscillator, but in a system the parasitic inductive part of C X can have a little influence. C X is only needed in order to suppress bias voltage at XTAL2 output. Recommended values are shown in table 1. Table 2 Proposal for a Protocol Table R X2 =... Ohm C X1 = C X2 I Q or P w R Qmax Comment 2.7 pf pf pf M e a s u r e m e n t R e s u l t s Semiconductor Group 14 of 38 AP
15 6.2 Safety Factor The safety factor SF is the relation between maximum test resistance R Qmax, which can be added in series to the quartz crystal but it is still oscillating, and the maximum load resonance resistance R Lmax. It gives a feeling of how much the resistance of the passive part of the oscillator circuitry can be increased (caused by the drive level dependence of the crystal) until the oscillation does not start any more. Depending on production quality and long time behaviour of all parts of the oscillator circuitry, the safety factor needs a certain minimum value to grant a problem-free operation of the oscillator for mass production and during life time. The qualification of the safety factor shown in table 3 is based on the experience of the Tele Quarz Group. Safety Factor: SF = RQmax RLmax Load Resonance Resistance: C0typ RLmax = R1max C L 2 Table 3 Qualification of the Safety Factor Safety Factor Qualification SF < 1.5 unsuitable 1.5 SF < 2 risky 2 SF < 3 suitable 3 SF < 5 safe SF 5 very safe Note: For oscillation frequencies higher than 24MHz it is strongly recommended to check whether the safety factor which can be achieved is sufficient for the system. In case the safety factor is not sufficient in fundamental mode, it is possible to use 3rd overtone mode (see appendix). Semiconductor Group 15 of 38 AP
16 6.3 Trouble Shooting For standard applications, the already described method to determine the safety factor by changing the load capacitors is sufficient and successful finding a appropriate safety factor. If the application system shows still problems, despite all information given in this application note was regarded then the following hints can solve the problem Pull down Resistor R X1 An additional resistor R X1, within the value 5 MΩ to 12 MΩ, in parallel to C X1 can also increase the safety factor, since the internal feedback resistor of the oscillator-inverter and the additional external resistor form a voltage divider at the input of the inverter, see figure 5. This combination decreases damping in the active part of the inverter. Therefore the start-up behaviour of the oscillation is improved, and the safety factor is increased. The additional resistor R X1 should only be used when the oscillation circuit is already optimized but the safety factor is not sufficient for the application Feedback Resistor R f An additional external feedback resistor with a value R f ~ 100kΩ stabilizes the operating point (DC point) of the oscillator inverter input, see figure 5. This combination improves the start-up behaviour in an application system with much noise caused by adjacent components or in systems with disturbance on the supply voltage. This problem can be seen in a start-up time which is to long or in a start-up time which is not stable. The additional external resistor R f should only be used when the oscillation circuit is already optimized but the safety factor or start-up behaviour is not sufficient for the application. Semiconductor Group 16 of 38 AP
17 Pull down Resistor R X1 Feedback Resistor R f to internal clock circuitry to internal clock circuitry XTAL1 XTAL2 (XTAL2) (XTAL1) XTAL1 XTAL2 (XTAL2) (XTAL1) R f Q R X2 Q R X2 R X1 C X1 C X2 C X1 C X2 GND GND Figure 5 Pull down Resistor R X1 and Feedback Resistor R f for Trouble shooting Semiconductor Group 17 of 38 AP
18 6.4 Qualification of the Results The basis for the evaluation of the measured results are the protocol tables. The results are displayed in evaluation diagrams shown in figure 6. For each protocol table with a fixed R X2 one evaluation diagram should be used. The evaluation diagram includes the characteristic curve for the safety factor SF and the drive level P W. It is also possible to display the resistance of the test resistor R Q and the crystal current I Q. In the evaluation diagram the specified minimum and maximum values of P W (I Q ) of the used crystal can be marked. From it results a fixed range for the allowed capacitance of C X1 and C X2. Depending on the circuit composition, the characteristic curve of SF (R Qmax ) includes very often a maximum for capacitance values in the C X1 / C X2 range of 0 pf to 3 pf. The recommended range for SF (R Qmax ) should be in the falling area of the characteristic curve as marked in the diagram. Depending on the selected area for SF (R Qmax ) a specific range for C X1 and C X2 is given. Now two areas for C X1 and C X2 are given, one by P W (I Q ) and the other by SF (R Qmax ). The capacitive values which are available in both areas are allowed for the oscillator circuit (see marked area in the diagram). This analysis has to be done for every R X2 value. The final selection of the components should be done under consideration of the necessary safety level, frequency, quality of the start-up behaviour of the oscillator, start-up time of the oscillation and the specified load capacitance C L of the crystal. Note: It is not recommended to include the maximum of SF (R Qmax ) because in many cases the gradient of the characteristic curve between 0 pf and 3 pf is very high. If C X1 and C X2 were chosen in that area, small parameter variations of the used components during production could reduce the safety level very fast. The consequence could be that the oscillator does not work in this case. SF (Safety Factor) R X2 =... Ohm P W (Drive Level) recomm. range max. allowed range min. 0 Range for C X1 / C X2 C X1 / C X2 [pf] Figure 6 Evaluation Diagram for C X1 and C X2 Semiconductor Group 18 of 38 AP
19 7 Oscillator Circuitry Layout Recommendations The layout of the oscillator circuit is important for the RF and EMC behaviour of the design. The use of this recommendation can help to reduce problems caused by the layout. This design recommendation is optimized on EMC aspects. For an optimal layout the following items have to be noted: 7.1 Avoidance of Capacitive Coupling The crosstalk between oscillator signals and others has to be minimized. Sensitive inputs have to be separated from outputs with a high amplitude. Note: The crosstalk between different layers also has to be analyzed. 7.2 Ground Connection of the Crystal Package The connection of the crystal package to the ground plane directly underneath the crystal and to the ground layer via an interlayer connection has the following advantages: The crystal metal package reduces the electromagnetic emission. The mechanical stability of the crystal can be increased. The ground layer and the additional ground plane underneath the crystal shield the oscillator. This shielding decouples all signals on the other PCB side. 7.3 Avoidance of Parallel Tracks of High Frequency Signals In order to reduce the crosstalk caused by capacitive or inductive coupling, tracks of high frequency signals should not be routed in parallel (also not on different layers!). 7.4 Ground Supply The ground supply must be realized on the base of a low impedance. The impedance can be made smaller by using thick and wide ground tracks. Ground loops have to be avoided, because they are working like antennas. Note: The connection to the ground should be done with a top-pin-clip because the heat of soldering can damage the quartz crystal. 7.5 Correct Module Placement Other RF modules should not be placed near the oscillator circuitry in order to prevent them from influencing the crystal functionality. Semiconductor Group 19 of 38 AP
20 7.6 Layout Recommendation Microcontroller Decoupling capacitance C B on the back side of the PCB V CC C B V SS Connection to Ground layer XTAL1 (XTAL2) GND C X1 R X2 XTAL2 (XTAL1) GND C Connection to X2 Ground layer Quartz Crystal Quartz Crystal package has to be grounded Figure 7 Layout Recommendation GND Connection to Ground layer 8 Recommendations of the Crystal Manufacturer Tele Quarz Group The preceding chapters have shown a possibility of how to find the appropriate values for the circuit components of a crystal oscillator circuitry which ensure a problem-free operation. Similar tests were done in a cooperation between Siemens (HL DC AT) and Tele Quarz Group. This work is already performed for different Siemens microcontrollers. The specialists of Tele Quarz Group have done the analyses with the aid of the microcontroller development group of Siemens HL DC AT. The results of this cooperation are presented in the appendix of this Application Note. The cooperation will be continued and the results will be added to this Application Note step by step. Note: The appendix shows recommendations for the appropriate circuit composition of the oscillator which run in most of all applications but they do not release the system designer from a verification in the original system. It is mandatory to perform own investigations concerning the safety factor to get a problem-free operation of the oscillator. This is necessary because every design has a specific influence on the oscillator (noise, layout etc.). Semiconductor Group 20 of 38 AP
21 9 Used Short Cuts C 0 : Shunt capacitance of the quartz crystal (static capacitance) C 0typ : Typical value of the shunt capacitance of the quartz crystal C 1 : Motional capacitance of the quartz crystal (dynamic capacitance). Mechanical equivalent is the elasticity of the quartz crystal hardware blank C 1typ : Typical value of the motional capacitance of the quartz crystal C L : Load capacitance of the system resp. quartz crystal C S : Stray capacitance of the system C X1, C X2 : Load capacitors C X : Capacitance to suppress bias voltage at XTAL2 output. C X2rest : Capacitance of C X2 in combination with L X in 3rd overtone mode C B : Decoupling capacitance for V CC and V SS on the Printed Circuit Board (PCB). Depending on the EMC behaviour the value should be in the range: 22nF to 100nF f LXCX2 f 3rd f fund I pp I Q L 1 L X P W Q : Parallel resonance frequency of L X and C X2 : Frequency of the 3rd overtone : Frequency of the fundamental mode : Peak to peak value of the quartz crystal current : Drive current : Motional inductance of the quartz crystal (dynamic inductance). Mechanical equivalent is the oscillating mass of the quartz crystal hardware blank. : Inductance for 3rd overtone mode : Drive level : Quartz Crystal R 1, R r : Series resistance of the quartz crystal (resonance resistance) in other technical descriptions also called: equivalent series resistance, ESR or transformed series resistance ). Mechanical equivalent is the moleculare friction, the damping by mechanical mounting system and accustical damping by the gasfilled housing. R 1typ : Typical value of the series resistance at room temperature R 1max : Maximum value of the series resistance at room temperature R 1max (TK) : Maximum value of the series resistance at the specified temperatur range. This value ist the base for calculation of the SF in this application note. R Ltyp, R Lmax : Typical and maximum load resonance resistor (in other technical descriptions also called: effective resistance ) R Q : Test resistor for calculation of safety level R Qmax : Maximum value of the test resistor which does not stop the oscillation R X1 : Pull down resistor to increase gain (trouble shooting) R X2 : Resistor which controls the drive level (damping resistor) : Additional external feedback resistor to stabilize DC point (trouble shooting) R f SF t st_up t off : Safety Factor : Start-up time of the oscillator : Oscillator off time for measurement of start-up behaviour Semiconductor Group 21 of 38 AP
22 L 1 C 1 R 1 Q C 0 Figure 8 Equivalent Circuit of a Quartz Crystal 10 General Information using the Appendix The Appendix includes recommendations for the right composition on external circuits for the C500 and C166 family. Each recommendation for the external circuits is only one of more different possibilities. The decision which composition is the right one, is not digital (go or not go) but has to be done in a analog way which offers more different results which fits to the system. The system designer has to decide which criterion of the application system concerning the oscillator has to be considered: safety factor, start-up behaviour, drive level, quartz crystal specification, frequency, EMC, layout demands etc. These facts are the base for the trade-off which external circuits fit best to the individual application system. The most important topic of the oscillator is the safety factor which gives the system designer a feeling about the start-up quality of the oscillator. The recommendations in the appendix show one possibility for the external circuits which is optimized to the start-up behaviour respectively the safety factor and the used type of quartz crystal. For microcontroller and quartz crystals which are not included in the tables please determine the safety factor in the target system as described in this Application Note. Semiconductor Group 22 of 38 AP
23 11 Appendix C500 Family All derivatives, steps and oscillator-inverter types of the C500 family shown in the table below are included in the recommendations of the following pages. For each type of oscillator-inverter there is given a proposal for the right composition on external circuits refered to different frequencies C500 Family: Relation between Oscillator-Inverter Type and Device Type Table 4 C500 Family Derivatives and Oscillator-Inverter Type Device Step Inverter SAx-C505A-4E AA Type_A SAx-C505C-2E AA Type_A SAx-C505CA-4E AA Type_A SAx-C513A-L / -R / -2R BB Type_A SAx-C515C-L / -8R AA Type_B SAx-80C517 DB Type_B SAx-80C537 SAx-C509L DA, DB Type_C Semiconductor Group 23 of 38 AP
24 11.2 C500 Family: Type_A Oscillator-Inverter The table below contains the recommendations for the external circuitry using a Type_A oscillatorinverter in fundamental mode. The quartz crystal data are included which are necessary for the calculation of the drive level (P W ) and safety factor (SF). The quartz crystal data are related to the quartz crystals of appendix Quartz Crystals. The measured values of R Qmax and the calculated values of P W and SF are based on these quartz crystals and the formulas presented in this ApNote. Table 5 C166 Family Derivatives including a Type_A Oscillator-Inverter Device Step Oscillator Frequency XTAL1 XTAL2 SAx-C505A-4E AA 2-20 MHz Input Output SAx-C505C-2E AA 2-20 MHz Input Output SAx-C505CA-4E AA 2-20 MHz Input Output SAx-C513A-L / -R / -2R BB 3,5-12 MHz Input Output Table 6 Recommendations for external circuitry used with a Type_A Oscillator-Inverter in Fundamental Mode Fundamental Mode: Type_A Oscillator-Inverter External Circuits Quartz Crystal Data Frequency [MHz] R X2 [Ω] C X1 [pf] (Input) C X2 [pf] (Output) C L [pf] C 0typ [pf] R 1typ [Ω] R 1max [Ω] R 1max (TK) [Ω] P W [µw] (@ 25 C, R 1typ ) R Qmax [Ω] Safety Factor SF , , , , , , , , , , , , ,89 Semiconductor Group 24 of 38 AP
25 11.3 C500 Family: Type_B Oscillator-Inverter The table below contains the recommendations for the external circuitry using a Type_B oscillatorinverter in fundamental mode. The quartz crystal data are included which are necessary for the calculation of the drive level (P W ) and safety factor (SF). The quartz crystal data are related to the quartz crystals of appendix Quartz Crystals. The measured values of R Qmax and the calculated values of P W and SF are based on these quartz crystals and the formulas presented in this ApNote. Table 7 C166 Family Derivatives including a Type_B Oscillator-Inverter Device Step Oscillator Frequency XTAL1 XTAL2 SAx-C515C-L / -8R AA 2-10 MHz Output (C X2 ) Input (C X1 ) SAx-80C517 SAx-80C537 DB 3,5-16 MHz Input (C X1 ) Output (C X2 ) Table 8 Recommendations for external circuitry used with a Type_B Oscillator-Inverter in Fundamental Mode Fundamental Mode: Type_B Oscillator-Inverter External Circuits Quartz Crystal Data Frequency [MHz] R X2 [Ω] C X1 [pf] (Input) C X2 [pf] (Output) C L [pf] C 0typ [pf] R 1typ [Ω] R 1max [Ω] R 1max (TK) [Ω] P W [µw] (@ 25 C, R 1typ ) R Qmax [Ω] Safety Factor SF , , , , , , , ,08 Semiconductor Group 25 of 38 AP
26 11.4 C500 Family: Type_C Oscillator-Inverter The table below contains the recommendations for the external circuitry using a Type_C oscillatorinverter in fundamental mode. The quartz crystal data are included which are necessary for the calculation of the drive level (P W ) and safety factor (SF). The quartz crystal data are related to the quartz crystals of appendix Quartz Crystals. The measured values of R Qmax and the calculated values of P W and SF are based on these quartz crystals and the formulas presented in this ApNote. Table 9 C166 Family Derivatives including a Type_C Oscillator-Inverter Device Step Oscillator Frequency XTAL1 XTAL2 SAx-C509L DA, DB 3,5-16 MHz Output (C X2 ) Input (C X1 ) Table 10 Recommendations for external circuitry used with a Type_C Oscillator-Inverter in Fundamental Mode Fundamental Mode: Type_C Oscillator-Inverter External Circuits Quartz Crystal Data Frequency [MHz] R X2 [Ω] C X1 [pf] (Input) C X2 [pf] (Output) C L [pf] C 0typ [pf] R 1typ [Ω] R 1max [Ω] R 1max (TK) [Ω] P W [µw] (@ 25 C, R 1typ ) R Qmax [Ω] Safety Factor SF , , , , , , , , ,64 Semiconductor Group 26 of 38 AP
27 12 Appendix C166 Family All derivatives, steps and oscillator-inverter types of the C166 family shown in the table below are included in the recommendations of the following pages. For each type of oscillator inverter there is given a proposal for the right composition on external circuits refered to different frequencies C166 Family: Relation between Oscillator-Inverter Type and Device Type Table 11 C166 Family Derivatives and Oscillator-Inverter Type Device Step Inverter SAx-C163-LF AB Type_R SAx-C165-LF CA Type_R SAx-C165-LM CA Type_R SAB-80C166(W)-M-Tx CB, DA, DB, DC Type_R SAB-83C166(W)-M-Tx CB, DA, DB, DC Type_R SAx-C167-LM BA, BB, BC Type_R SAx-C167S-4RM AA, AE, BA, BB, DA, DB Type_R SAx-C167SR-LM AB, BA, CB, DA, DB Type_R SAx-C167CR-LM AB, BA, BB, CA, CB, BE, DA, DB Type_R SAx-C167CR-4RM AA, AB, AC, DA, DB Type_R SAx-C167CR-16RM AA Type_R SAx C161RI AA Type_LP1 SAx C161CI AA Type_LP2 Type_RTC1 SAx C161RI BA Type_LP2 SAx C164CI BA Type_LP2 Semiconductor Group 27 of 38 AP
28 12.2 C166 Family: Type_R Oscillator-Inverter The table below shows the derivatives including a Type_R oscillator-inverter. The tables on the next two pages include the recommendations for fundamental mode and 3rd overtone mode. Table 12 C166 Family Derivatives including a Type_R Oscillator-Inverter Device Step Oscillator Frequency SAx-C163-LF AB 3,5-24 (40) MHz SAx-C165-LF CA 3,5-24 (40) MHz SAx-C165-LM CA 3,5-24 (40) MHz SAB-80C166(W)-M-Tx CB, DA, DB, DC 3,5-24 (40) MHz SAB-83C166(W)-M-Tx CB, DA, DB, DC 3,5-24 (40) MHz SAx-C167-LM BA, BB, BC 3,5-24 (40) MHz SAx-C167S-4RM AA, AE, BA, BB, DA, DB 3,5-24 (40) MHz SAx-C167SR-LM AB, BA, CB, DA, DB 3,5-24 (40) MHz SAx-C167CR-LM AB, BA, BB, CA, CB, BE, DA, DB 3,5-24 (40) MHz SAx-C167CR-4RM AA, AB, AC, DA, DB 3,5-24 (40) MHz SAx-C167CR-16RM AA 3,5-24 (40) MHz Semiconductor Group 28 of 38 AP
29 C166 Family: Type_R Oscillator-Inverter Fundamental Mode The table below contains the recommendations for the external circuitry using a Type_R oscillatorinverter in fundamental mode. The quartz crystal data are included which are necessary for the calculation of the drive level (P W ) and safety factor (SF). The quartz crystal data are related to the quartz crystals of appendix Quartz Crystals. The measured values of R Qmax and the calculated values of P W and SF are based on these quartz crystals and the formulas presented in this ApNote. Table 13 Recommendations for external circuitry used with a Type_R Oscillator-Inverter in Fundamental Mode Fundamental Mode: Type_R Oscillator-Inverter External Circuits Quartz Crystal Data Frequency [MHz] R X2 [Ω] C X1 [pf] (Input) C X2 [pf] (Output) C L [pf] C 0typ [pf] R 1typ [Ω] R 1max [Ω] R 1max (TK) [Ω] P W [µw] (@ 25 C, R 1typ ) R Qmax [Ω] Safety Factor SF , , , , , , , , , , , , ,08 Semiconductor Group 29 of 38 AP
30 C166 Family: Type_R Oscillator-Inverter 3rd Overtone Mode The table below contains the recommendations for the external circuitry using a Type_R oscillatorinverter in 3rd overtone mode. The quartz crystal data are included which are necessary for the calculation of the drive level (P W ) and safety factor (SF). The quartz crystal data are related to the quartz crystals of appendix Quartz Crystals. The measured value of R Qmax and the calculated values of P W and SF are based on these quartz crystals and the formulas presented in this ApNote. Table 14 Recommendations for external circuitry used with a Type_R Oscillator-Inverter in 3rd Overtone Mode 3rd Overtone Mode: External Circuits Type_R Oscillator-Inverter Quartz Crystal Data Frequency [MHz] R X2 [Ω] C X1 [pf] (Input) C X2 [pf] (Output) C X [nf] L X [µh] C L [pf] C 0typ [pf] R 1typ [Ω] R 1max [Ω] R 1max (TK) [Ω] P W [µw] (@ 25 C, R 1typ ) R Qmax [Ω] Safety Factor SF , , ,76 Semiconductor Group 30 of 38 AP
31 12.3 C166 Family: Type_LP1 Oscillator-Inverter The table below contains the recommendations for the external circuitry using a Type_LP1 oscillator-inverter in fundamental mode. The quartz crystal data are included which are necessary for the calculation of the drive level (P W ) and safety factor (SF). The quartz crystal data are related to the quartz crystals of appendix Quartz Crystals. The measured values of R Qmax and the calculated values of P W and SF are based on these quartz crystals and the formulas presented in this ApNote. Table 15 C166 Family Derivatives including a Type_LP1 Oscillator-Inverter Device Step Oscillator Frequency SAx C161RI AA 3,5-16 MHz Table 16 Recommendations for external circuitry used with a Type_LP1 Oscillator-Inverter in Fundamental Mode Fundamental Mode: Type_LP1 Oscillator-Inverter External Circuits Quartz Crystal Data Frequency [MHz] R X2 [Ω] C X1 [pf] (Input) C X2 [pf] (Output) C L [pf] C 0typ [pf] R 1typ [Ω] R 1max [Ω] R 1max (TK) [Ω] P W [µw] (@ 25 C, R 1typ ) R Qmax [Ω] Safety Factor SF ,7 4, > ,2 8, > > > > > > > > > > > > 40 Semiconductor Group 31 of 38 AP
32 12.4 C166 Family: Type_LP2 Oscillator-Inverter The table below contains the recommendations for the external circuitry using a Type_LP2 oscillator-inverter in fundamental mode. The quartz crystal data are included which are necessary for the calculation of the drive level (P W ) and safety factor (SF). The quartz crystal data are related to the quartz crystals of appendix Quartz Crystals. The measured values of R Qmax and the calculated values of P W and SF are based on these quartz crystals and the formulas presented in this ApNote. Table 17 C166 Family Derivatives including a Type_LP2 Oscillator-Inverter Device Step Oscillator Frequency SAx C161CI AA 3,5-16 MHz SAx C161RI BA 3,5-16 MHz SAx C164CI BA 3,5-16 MHz Table 18 Recommendations for external circuitry used with a Type_LP2 Oscillator-Inverter in Fundamental Mode Fundamental Mode: Type_LP2 Oscillator-Inverter External Circuits Quartz Crystal Data Frequency [MHz] R X2 [Ω] C X1 [pf] (Input) C X2 [pf] (Output) C L [pf] C 0typ [pf] R 1typ [Ω] R 1max [Ω] R 1max (TK) [Ω] P W [µw] (@ 25 C, R 1typ ) R Qmax [Ω] Safety Factor SF ,7 2, , ,3 4, , ,7 8, , , , , , , ,01 Semiconductor Group 32 of 38 AP
33 12.5 C166 Family: Type_RTC1 Oscillator-Inverter The table below contains the recommendations for the external circuitry using a Type_RTC1 oscillator-inverter in fundamental mode. The quartz crystal data are included which are necessary for the calculation of the safety factor (SF). The quartz crystal data are related to the quartz crystals of appendix Quartz Crystals. The measured value of R Qmax and the calculated value of SF are based on these quartz crystals and the formulas presented in this ApNote. Table 19 C166 Family Derivatives including a Type_RTC1 Oscillator-Inverter Device Step Oscillator Frequency XTAL3 XTAL4 SAx C161CI AA 32,768 khz Input (C X1 ) Output (C X2 ) Table 20 Recommendations for external circuitry used with a RTC1 Oscillator-Inverter in Fundamental Mode Fundamental Mode: Type_RTC1 Oscillator-Inverter External Circuits Quartz Crystal Data Frequency [khz] R X2 [Ω] C X1 [pf] (Input) C X2 [pf] (Output) C L [pf] C 0typ [pf] R 1typ [Ω] R 1max [Ω] R 1max (TK) [Ω] R Qmax [Ω] Safety Factor SF 32, , , ,08 Semiconductor Group 33 of 38 AP
34 13 Quartz Crystals for the C500 and C166 Family 13.1 Fundamental Mode Quartz Crystal for Standard Temperature Range Table 21 Quartz Crystals for all Oscillator-Inverter used in Fundamental Mode Standard Temperature Range from - 20 C to 70 C Quartz Crystal Specification for Fundamental Mode: Frequency [MHz] Can hight 6.6mm low profile SH66 HC49 Can hight 13.5mm SMD-Mounting with Clip CS20 Can hight 8.8mm Standard- Enclosure HC52 Can hight 8.8mm SMD-Mounting with Clip CS10 40 C167CR40 C167CR40S C167CR40A C167CR40AS 32 C167CR32 C167CR32S C167CR32A C167CR32AS 24 C167CR24 C167CR24S C167CR24A C167CR24AS 20 C167CR20 C167CR20S C167CR20A C167CR20AS 18 C167CR18 C167CR18S C167CR18A C167CR18AS 16 C167CR16 C167CR16S C167CR16A C167CR16AS 12 C167CR12 C167CR12S C167CR12A C167CR12AS 10 C167CR10 C167CR10S C167CR10A C167CR10AS 8 C167CR08 C167CR08S C167CR08A C167CR08AS 6 C167CR06 C167CR06S C167CR06A C167CR06AS 5 C167CR05 C167CR05S C167CR05A C167CR05AS C167CR04S The specifications C167CRxxxx are for the use in standard temperature range from - 20 C to 70 C. For further information please contact your local Tele Quarz Group sales office. Semiconductor Group 34 of 38 AP
35 13.2 Fundamental Mode Quartz Crystal for Advanced Temperature Range Table 22 Quartz Crystals for all Oscillator-Inverter used in Fundamental Mode Advanced Temperature Range from - 40 C to 125 C for Automotive Applications Quartz Crystal Specification for Fundamental Mode: Frequency [MHz] Can hight 6.6mm low profile SH66 HC49 Can hight 13.5mm SMD-Mounting with Clip CS20 Can hight 8.8mm Standard- Enclosure HC52 Can hight 8.8mm SMD-Mounting with Clip CS10 20 KFZ0010 KFZ0010S KFZ0010A KFZ0010AS 18 KFZ0011 KFZ0011S KFZ0011A KFZ0011AS 16 KFZ0012 KFZ0012S KFZ0012A KFZ0012AS 12 KFZ0013 KFZ0013S KFZ0013A KFZ0013AS 10 KFZ0014 KFZ0014S KFZ0014A KFZ0014AS 8 KFZ0015 KFZ0015S KFZ0015A KFZ0015AS 6 KFZ0016 KFZ0016S KFZ0016A KFZ0016AS 5 KFZ0017 KFZ0017S KFZ0017A KFZ0017AS KFZ0018S The specifications KFZ00xxxx are for the use in advanced temperature range from - 40 C to 125 C for automotive applications. For further information please contact your local Tele Quarz Group sales office. Semiconductor Group 35 of 38 AP
36 13.3 3rd Overtone Mode Quartz Crystal for Standard Temperature Range Table 23 Quartz Crystals for all Oscillator-Inverter used in 3rd Overtone Mode Standard Temperature Range from - 20 C to 70 C Quartz Crystal Specification for 3rd Overtone Mode: Frequency [MHz] Can hight 6.6mm low profile SH66 HC49 Can hight 13.5mm SMD-Mounting with Clip CS20 Can hight 8.8mm Standard- Enclosure HC52 Can hight 8.8mm SMD-Mounting with Clip CS C167CR403S C167CR403A C167CR403AS The specifications C167CR403xx are for the use in standard temperature range from - 20 C to 70 C. For further information please contact your local Tele Quarz Group sales office rd Overtone Mode Quartz Crystal for Advanced Temperature Range Table 24 Quartz Crystals for all Oscillator-Inverter used in 3rd Overtone Mode Advanced Temperature Range from - 40 C to 125 C for Automotive Applications Quartz Crystal Specification for 3rd Overtone Mode: Frequency [MHz] Can hight 6.6mm low profile SH66 HC49 Can hight 13.5mm SMD-Mounting with Clip CS20 Can hight 8.8mm Standard- Enclosure HC52 Can hight 8.8mm SMD-Mounting with Clip CS KFZ0009S KFZ0009A KFZ0009AS The specifications KFZ0009xx are for the use in advanced temperature range from - 40 C to 125 C for automotive applications. For further information please contact your local Tele Quarz Group sales office. Semiconductor Group 36 of 38 AP
Crystal Oscillator of the C500 and C166 Microcontroller Families
Microcontrollers ApNote AP242002 Crystal Oscillator of the C500 and C166 Microcontroller Families The microcontrollers of the C500/C166 Family include the active part of the oscillator. This document explains
Crystal or oscillator which one and how to apply?
Crystal or oscillator which one and how to apply? When designing a new electronic circuit, design engineers often need to consider if a crystal or an oscillator is the suitable choice: How many space is
Characteristics of Crystal. Piezoelectric effect of Quartz Crystal
Characteristics of Crystal Piezoelectric effect of Quartz Crystal The quartz crystal has a character when the pressure is applied to the direction of the crystal axis, the electric change generates on
Crystal Oscillator/Resonator Guidelines for ez80 and ez80acclaim! Devices
Technical Note Crystal Oscillator/Resonator Guidelines for TN001305-0307 General Overview ZiLOG s ez80 MPU and ez80acclaim! Flash microcontrollers feature on-chip oscillators for use with external crystals
UART CRYSTAL OSCILLATOR DESIGN GUIDE. 1. Frequently Asked Questions associated with UART Crystal Oscillators
UART CRYSTAL OSCILLATOR DESIGN GUIDE March 2000 Author: Reinhardt Wagner 1. Frequently Asked Questions associated with UART Crystal Oscillators How does a crystal oscillator work? What crystal should I
HT32 Series Crystal Oscillator, ADC Design Note and PCB Layout Guide
HT32 Series rystal Oscillator, AD Design Note and PB Layout Guide HT32 Series rystal Oscillator, AD Design Note and PB Layout Guide D/N:AN0301E Introduction This application note provides some hardware
CMT2300AW Schematic and PCB Layout Design Guideline
AN141 CMT2300AW Schematic and PCB Layout Design Guideline Introduction This document is the CMT2300AW Application Development Guideline. It will explain how to design and use the CMT2300AW schematic and
Edition Published by Infineon Technologies AG Munich, Germany 2010 Infineon Technologies AG All Rights Reserved.
XC800 Family AP08110 Application Note V1.0, 2010-06 Microcontrollers Edition 2010-06 Published by Infineon Technologies AG 81726 Munich, Germany 2010 Infineon Technologies AG All Rights Reserved. LEGAL
AN2441 Application note
Application note Low cost effective oscillator for STR71x MCUs Introduction The STR71x 32-bit MCU family from STMicroelectronics runs with an external oscillator which is connected to the CK pin. A straightforward
AN2867 Application note
Application note Oscillator design guide for ST microcontrollers Introduction Most designers are familiar with oscillators (Pierce-Gate topology), but few really understand how they operate, let alone
Clocking the Data ABSTRACT INTRODUCTION KEY WORDS
Clocking the Data By Jerry Shirar N9XR 6847 Edgebrook Lane Hanover Park, IL 60133 radio.n9xr@gmail.com ABSTRACT Many oscillators attached to the microprocessors and microcontrollers today are simply inverter
AN2867 Application note
Application note Oscillator design guide for STM8S, STM8A and STM32 microcontrollers Introduction Most designers are familiar with oscillators (Pierce-Gate topology), but few really understand how they
AN2867 Application note
Application note Oscillator design guide for ST microcontrollers Introduction Most designers are familiar with oscillators (Pierce-Gate topology), but few really understand how they operate, let alone
Application Note SAW-Components
Application Note SAW-Components Comparison between negative impedance oscillator (Colpitz oscillator) and feedback oscillator (Pierce structure) App.: Note #13 Author: Alexander Glas EPCOS AG Updated:
PART MAX2605EUT-T MAX2606EUT-T MAX2607EUT-T MAX2608EUT-T MAX2609EUT-T TOP VIEW IND GND. Maxim Integrated Products 1
19-1673; Rev 0a; 4/02 EVALUATION KIT MANUAL AVAILABLE 45MHz to 650MHz, Integrated IF General Description The are compact, high-performance intermediate-frequency (IF) voltage-controlled oscillators (VCOs)
AN4819 Application note
Application note PCB design guidelines for the BlueNRG-1 device Introduction The BlueNRG1 is a very low power Bluetooth low energy (BLE) single-mode system-on-chip compliant with Bluetooth specification
Application Note SAW-Components
Application Note SAW-Components Fundamentals of a SAWR stabilised Pierce oscillator. Schematic and PCB layout for a SAWR stabilised oscillator working at 915MHz and at 868.3MHz. App. Note #21 Author: Alexander
AN2867 Application note
Application note Oscillator design guide for STM8S, STM8A and STM32 microcontrollers Introduction Most designers are familiar with oscillators (Pierce-Gate topology), but few really understand how they
GX434 Monolithic 4x1 Video Multiplexer
Monolithic x Video Multiplexer DATA SHEET FEATURES low differential gain: 0.0% typ. at. MHz low differential phase: 0.0 deg. typ. at. MHz low insertion loss: 0.0 db max at 00 khz low disabled power consumption:.
2A, 23V, 380KHz Step-Down Converter
2A, 23V, 380KHz Step-Down Converter General Description The is a buck regulator with a built-in internal power MOSFET. It achieves 2A continuous output current over a wide input supply range with excellent
HA7210, HA kHz to 10MHz, Low Power Crystal Oscillator. Description. Features. Ordering Information. Applications. Typical Application Circuits
SEMICONDUCTOR HA, HA November 99 khz to MHz, Low Power Crystal Oscillator Features Description Single Supply Operation at khz.......... V to V Operating Frequency Range........ khz to MHz Supply Current
Design note for YIC Quartz Crystal Unit
Design note for YIC Quartz Crystal Unit CRYSTAL EQUIVALENT CIRCUIT The equivalent circuit of a quartz crystal is shown to explain the basic elements governing the crystal characteristics and performance.
LM2412 Monolithic Triple 2.8 ns CRT Driver
Monolithic Triple 2.8 ns CRT Driver General Description The is an integrated high voltage CRT driver circuit designed for use in high resolution color monitor applications. The IC contains three high input
ICS LOW EMI CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET
DATASHEET ICS180-51 Description The ICS180-51 generates a low EMI output clock from a clock or crystal input. The device uses IDT s proprietary mix of analog and digital Phase-Locked Loop (PLL) technology
Class-D Audio Power Amplifiers: PCB Layout For Audio Quality, EMC & Thermal Success (Home Entertainment Devices)
Class-D Audio Power Amplifiers: PCB Layout For Audio Quality, EMC & Thermal Success (Home Entertainment Devices) Stephen Crump http://e2e.ti.com Audio Power Amplifier Applications Audio and Imaging Products
EVB /433MHz Transmitter Evaluation Board Description
Features! Fully integrated, PLL-stabilized VCO! Frequency range from 310 MHz to 440 MHz! FSK through crystal pulling allows modulation from DC to 40 kbit/s! High FSK deviation possible for wideband data
ICS722 LOW COST 27 MHZ 3.3 VOLT VCXO. Description. Features. Block Diagram DATASHEET
DATASHEET ICS722 Description The ICS722 is a low cost, low-jitter, high-performance 3.3 volt designed to replace expensive discrete s modules. The on-chip Voltage Controlled Crystal Oscillator accepts
EVB /915MHz Transmitter Evaluation Board Description
General Description The TH708 antenna board is designed to optimally match the differential power amplifier output to a loop antenna. The TH708 can be populated either for FSK, ASK or FM transmission.
F²MC-8L/8FX/16LX/FR FAMILY
Fujitsu Microelectronics Europe Application Note MCU-AN-300007-E-V13 F²MC-8L/8FX/16LX/FR FAMILY 8/16/32-BIT MICROCONTROLLER ALL SERIES OSCILLATOR CIRCUIT CONFIGURATION APPLICATION NOTE Revision History
Short Tutorial on Quartz Crystals and Oscillators
Short Tutorial on Quartz Crystals and Oscillators Contents 1. Quartz Crystals...2 1.1 Equivalent circuit of a quartz crystal...2 1.2. Quartz crystal in 'series resonance'...5 1.2.1. Influence of the shunt
433MHz Single Chip RF Transmitter
433MHz Single Chip RF Transmitter nrf402 FEATURES True single chip FSK transmitter Few external components required On chip UHF synthesiser No set up or configuration 20kbit/s data rate 2 channels Very
MP1496S High-Efficiency, 2A, 16V, 500kHz Synchronous, Step-Down Converter
MP1496S High-Efficiency, 2A, 16, 500kHz Synchronous, Step-Down Converter DESCRIPTION The MP1496S is a high-frequency, synchronous, rectified, step-down, switch-mode converter with built-in power MOSFETs.
MK LOW PHASE NOISE T1/E1 CLOCK GENERATOR. Features. Description. Block Diagram DATASHEET. Pullable Crystal
DATASHEET LOW PHASE NOISE T1/E1 CLOCK ENERATOR MK1581-01 Description The MK1581-01 provides synchronization and timing control for T1 and E1 based network access or multitrunk telecommunication systems.
PCB Design Guidelines for GPS chipset designs. Section 1. Section 2. Section 3. Section 4. Section 5
PCB Design Guidelines for GPS chipset designs The main sections of this white paper are laid out follows: Section 1 Introduction Section 2 RF Design Issues Section 3 Sirf Receiver layout guidelines Section
Application Note Receivers MLX71120/21 With LNA1-SAW-LNA2 configuration
Designing with MLX71120 and MLX71121 receivers using a SAW filter between LNA1 and LNA2 Scope Many receiver applications, especially those for automotive keyless entry systems require good sensitivity
10MHz to 500MHz VCO Buffer Amplifiers with Differential Outputs
19-4797; Rev 0; 2/99 EVALUATION KIT MANUAL FOLLOWS DATA SHEET 10MHz to 500MHz VCO Buffer Amplifiers General Description The / are flexible, low-cost, highreverse-isolation buffer amplifiers for applications
Application Note 58 Crystal Considerations with Dallas Real Time Clocks
Application Note 58 Crystal Considerations with Dallas Real Time Clocks Dallas Semiconductor offers a variety of real time clocks (RTCs). The majority of these are available either as integrated circuits
2. Design Recommendations when Using EZRadioPRO RF ICs
EZRADIOPRO LAYOUT DESIGN GUIDE 1. Introduction The purpose of this application note is to help users design EZRadioPRO PCBs using design practices that allow for good RF performance. This application note
MP1496 High-Efficiency, 2A, 16V, 500kHz Synchronous, Step-Down Converter
The Future of Analog IC Technology DESCRIPTION The MP1496 is a high-frequency, synchronous, rectified, step-down, switch-mode converter with built-in power MOSFETs. It offers a very compact solution to
LM2462 Monolithic Triple 3 ns CRT Driver
LM2462 Monolithic Triple 3 ns CRT Driver General Description The LM2462 is an integrated high voltage CRT driver circuit designed for use in color monitor applications. The IC contains three high input
250 MHz, General Purpose Voltage Feedback Op Amps AD8047/AD8048
5 MHz, General Purpose Voltage Feedback Op Amps AD8/AD88 FEATURES Wide Bandwidth AD8, G = + AD88, G = + Small Signal 5 MHz 6 MHz Large Signal ( V p-p) MHz 6 MHz 5.8 ma Typical Supply Current Low Distortion,
BA Features. General Description. Applications. Marking Information. 3W Mono Filterless Class D Audio Power Amplifier
3W Mono Filterless Class D Audio Power Amplifier General Description The BA16853 is a cost-effective mono Class D audio power amplifier that assembles in Dual Flat No-Lead Plastic Package (DFN-8). Only
Application Note, Rev.1.0, November 2010 TLE8366. The Demoboard. Automotive Power
Application Note, Rev.1.0, November 2010 TLE8366 Automotive Power Table of Contents 1 Abstract...3 2 Introduction...3 3 The Demo board...4 3.1 Quick start...4 3.2 The Schematic...5 3.3 Bill of Material...6
Chapter 16 PCB Layout and Stackup
Chapter 16 PCB Layout and Stackup Electromagnetic Compatibility Engineering by Henry W. Ott Foreword The PCB represents the physical implementation of the schematic. The proper design and layout of a printed
MP2313 High Efficiency 1A, 24V, 2MHz Synchronous Step Down Converter
The Future of Analog IC Technology MP2313 High Efficiency 1A, 24V, 2MHz Synchronous Step Down Converter DESCRIPTION The MP2313 is a high frequency synchronous rectified step-down switch mode converter
ICS CLOCK SYNTHESIZER FOR PORTABLE SYSTEMS. Description. Features. Block Diagram PRELIMINARY DATASHEET
PRELIMINARY DATASHEET ICS1493-17 Description The ICS1493-17 is a low-power, low-jitter clock synthesizer designed to replace multiple crystals and oscillators in portable audio/video systems. The device
AN4630. PCB design guidelines for the BlueNRG and BlueNRG-MS devices. Application note. Introduction
Application note PCB design guidelines for the BlueNRG and BlueNRG-MS devices Introduction The BlueNRG and BlueNRG-MS are very low power Bluetooth low energy (BLE) single-mode network processor devices,
High Speed Clock Distribution Design Techniques for CDC 509/516/2509/2510/2516
High Speed Clock Distribution Design Techniques for CDC 509/516/2509/2510/2516 APPLICATION REPORT: SLMA003A Boyd Barrie Bus Solutions Mixed Signals DSP Solutions September 1998 IMPORTANT NOTICE Texas Instruments
AN1995 Evaluating the SA605 SO and SSOP demo-board
RF COMMUNICATIONS PRODUCTS Evaluating the SA605 SO and SSOP demo-board Alvin K. Wong 997 Oct 9 Philips Semiconductors Author: Alvin K. Wong INTRODUCTION With the increasing demand for smaller and lighter
GX4201 Wideband, Monolithic 1x1 Video Crosspoint Switch
GX21 Wideband, Monolithic 1x1 Video Crosspoint Switch DATA SHEET FEATURES - db bandwidth, MHz with C L = pf off isolation at 1 MHz, db differential phase and gain at. MHz,.1 &.2% µw disabled power consumption
Communication Circuit Lab Manual
German Jordanian University School of Electrical Engineering and IT Department of Electrical and Communication Engineering Communication Circuit Lab Manual Experiment 3 Crystal Oscillator Eng. Anas Alashqar
MP1495 High Efficiency 3A, 16V, 500kHz Synchronous Step Down Converter
The Future of Analog IC Technology DESCRIPTION The MP1495 is a high-frequency, synchronous, rectified, step-down, switch-mode converter with built-in power MOSFETs. It offers a very compact solution to
LM4752 Stereo 11W Audio Power Amplifier
LM4752 Stereo 11W Audio Power Amplifier General Description The LM4752 is a stereo audio amplifier capable of delivering 11W per channel of continuous average output power to a 4Ω load, or 7W per channel
Exclusive Technology Feature. Integrated Driver Shrinks Class D Audio Amplifiers. Audio Driver Features. ISSUE: November 2009
ISSUE: November 2009 Integrated Driver Shrinks Class D Audio Amplifiers By Jun Honda, International Rectifier, El Segundo, Calif. From automotive entertainment to home theater systems, consumers are demanding
Crystal Units Surface Mount Type CX2520SB (CX-2520SB) mm for Audio & Visual, Office Equipment
Surface Mount Type CX2520SB (CX-2520SB) 2.5 2.0mm for Audio & Visual, Office Equipment Pb Free Crystal unit for audio-visual, office equipment Ultra-miniature and low profile (2.5x2.0x0.45mm) Ceramic package
ICS LOW EMI CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET
DATASHEET ICS180-01 Description The ICS180-01 generates a low EMI output clock from a clock or crystal input. The device uses IDT s proprietary mix of analog and digital Phase Locked Loop (PLL) technology
SHRINKING THE QUARTZ CRYSTAL RESONATOR
SHRINKING THE QUARTZ CRYSTAL RESONATOR Chris Watts, Chief Engineer, Golledge Electronics Introduction As with the rest of electronics there has been a move from leaded packages to surface mount and ever
Reference Oscillator Crystal Requirements for MKW40 and MKW30 Device Series
Freescale Semiconductor, Inc. Application Note Document Number: AN5177 Rev. 0, 08/2015 Reference Oscillator Crystal Requirements for MKW40 and MKW30 Device Series 1 Introduction This document describes
Course Introduction. Content: 19 pages 3 questions. Learning Time: 30 minutes
Course Introduction Purpose: This course discusses techniques that can be applied to reduce problems in embedded control systems caused by electromagnetic noise Objectives: Gain a basic knowledge about
LM2405 Monolithic Triple 7 ns CRT Driver
LM2405 Monolithic Triple 7 ns CRT Driver General Description The LM2405 is an integrated high voltage CRT driver circuit designed for use in color monitor applications The IC contains three high input
CURRENT MODE PWM CONTROLLER LM3842A/3A/4A/5A
CURRENT MODE PWM CONTROLLER LMA/A/A/5A FEATURES SOP/ DIP PIN Configulation Automatic feed forward compensation Optimized for offline converter Double pulse suppression Current mode operation to 500 KHz
PART 20 IF_IN LO_V CC 10 TANK 11 TANK 13 LO_GND I_IN 5 Q_IN 6 Q_IN 7 Q_IN 18 V CC
19-0455; Rev 1; 9/98 EALUATION KIT AAILABLE 3, Ultra-Low-Power Quadrature General Description The combines a quadrature modulator and quadrature demodulator with a supporting oscillator and divide-by-8
ICS HIGH PERFORMANCE VCXO. Features. Description. Block Diagram DATASHEET
DATASHEET ICS3726-02 Description The ICS3726-02 is a low cost, low-jitter, high-performance designed to replace expensive discrete s modules. The ICS3726-02 offers a wid operating frequency range and high
EVALUATION KIT AVAILABLE 300MHz to 450MHz High-Efficiency, Crystal-Based +13dBm ASK Transmitter 3.0V. 100nF DATA INPUT
19-31; Rev 4; /11 EVALUATION KIT AVAILABLE 300MHz to 450MHz High-Efficiency, General Description The crystal-referenced phase-locked-loop (PLL) VHF/UHF transmitter is designed to transmit OOK/ASK data
TS3022. Rail-to-rail 1.8 V high-speed dual comparator. Applications. Description. Features
TS22 Rail-to-rail 1.8 V high-speed dual comparator Datasheet - production data Applications Telecom Instrumentation Signal conditioning High-speed sampling systems Portable communication systems Automotive
300MHz to 450MHz High-Efficiency, Crystal-Based +13dBm ASK Transmitter
EVALUATION KIT AVAILABLE MAX044 General Description The MAX044 crystal-referenced phase-locked-loop (PLL) VHF/UHF transmitter is designed to transmit OOK/ASK data in the 300MHz to 450MHz frequency range.
Data Sheet, V 1.1, July 2006 TDK5110F. 434 MHz ASK/FSK Transmitter in 10-pin Package Version 1.1. Wireless Control Components. Never stop thinking.
Data Sheet, V 1.1, July 2006 TDK5110F 434 MHz ASK/FSK Transmitter in 10-pin Package Version 1.1 Wireless Control Components Never stop thinking. Edition 2006-07-10 Published by Infineon Technologies AG,
LM V Monolithic Triple Channel 15 MHz CRT DTV Driver
220V Monolithic Triple Channel 15 MHz CRT DTV Driver General Description The is a triple channel high voltage CRT driver circuit designed for use in DTV applications. The IC contains three high input impedance,
MK SPREAD SPECTRUM MULTIPLIER CLOCK. Description. Features. Block Diagram DATASHEET
DATASHEET MK1714-01 Description The MK1714-01 is a low cost, high performance clock synthesizer with selectable multipliers and percentages of spread spectrum designed to generate high frequency clocks
ICS7151A-50 SPREAD SPECTRUM CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET
DATASHEET ICS7151A-50 Description The ICS7151A-50 is a clock generator for EMI (Electromagnetic Interference) reduction. Spectral peaks are attenuated by modulating the system clock frequency. Down or
MK SPREAD SPECTRUM MULTIPLIER CLOCK. Description. Features. Block Diagram DATASHEET
DATASHEET MK1714-02 Description The MK1714-02 is a low cost, high performance clock synthesizer with selectable multipliers and percentages of spread designed to generate high frequency clocks with low
Features. Applications SOT-23-5
135MHz, Low-Power SOT-23-5 Op Amp General Description The is a high-speed, unity-gain stable operational amplifier. It provides a gain-bandwidth product of 135MHz with a very low, 2.4mA supply current,
EVALUATION KIT AVAILABLE 10MHz to 1050MHz Integrated RF Oscillator with Buffered Outputs. Typical Operating Circuit. 10nH 1000pF MAX2620 BIAS SUPPLY
19-1248; Rev 1; 5/98 EVALUATION KIT AVAILABLE 10MHz to 1050MHz Integrated General Description The combines a low-noise oscillator with two output buffers in a low-cost, plastic surface-mount, ultra-small
QPLL Manual. Quartz Crystal Based Phase-Locked Loop for Jitter Filtering Application in LHC. Paulo Moreira. CERN - EP/MIC, Geneva Switzerland
QPLL Manual Quartz Crystal Based Phase-Locked Loop for Jitter Filtering Application in LHC Paulo Moreira CERN - EP/MIC, Geneva Switzerland 2004-01-26 Version 1.0 Technical inquires: Paulo.Moreira@cern.ch
Analogue circuit design for RF immunity
Analogue circuit design for RF immunity By EurIng Keith Armstrong, C.Eng, FIET, SMIEEE, www.cherryclough.com First published in The EMC Journal, Issue 84, September 2009, pp 28-32, www.theemcjournal.com
MK VCXO-BASED FRAME CLOCK FREQUENCY TRANSLATOR. Features. Description. Block Diagram DATASHEET. Pullable Crystal
DATASHEET MK2059-01 Description The MK2059-01 is a VCXO (Voltage Controlled Crystal Oscillator) based clock generator that produces common telecommunications reference frequencies. The output clock is
ICS276 TRIPLE PLL FIELD PROGRAMMABLE VCXO CLOCK SYNTHESIZER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS276 Description The ICS276 field programmable VCXO clock synthesizer generates up to three high-quality, high-frequency clock outputs including multiple reference clocks from a low-frequency
CW Modulator Using Pin Diodes
Wolfgang Schneider, DJ8ES CW Modulator Using Pin Diodes This article describes a CW modulator for radio applications which is simple and uncomplicated from the rf technology point of view. The call sign
14 MHz Single Side Band Receiver
EPFL - LEG Laboratoires à options 8 ème semestre MHz Single Side Band Receiver. Objectives. The objective of this work is to calculate and adjust the key elements of an Upper Side Band Receiver in the
AN2158. Designing with the MC68HC908JL/JK Microcontroller Family. Introduction. Semiconductor Products Sector Application Note
Order this document by /D Semiconductor Products Sector Designing with the MC68HC908JL/JK Microcontroller Family By Yan-Tai Ng Applications Engineering Microcontroller Division Hong Kong Introduction This
ICS LOW EMI CLOCK GENERATOR. Features. Description. Block Diagram DATASHEET
DATASHEET ICS10-52 Description The ICS10-52 generates a low EMI output clock from a clock or crystal input. The device uses ICS proprietary mix of analog and digital Phase-Locked Loop (PLL) technology
AN2867 Application note
Application note Oscillator design guide for STM8S, STM8A and STM32 microcontrollers Introduction Most designers are familiar with oscillators (Pierce-Gate topology), but few really understand how they
Supply Voltage Supervisor TL77xx Series. Author: Eilhard Haseloff
Supply Voltage Supervisor TL77xx Series Author: Eilhard Haseloff Literature Number: SLVAE04 March 1997 i IMPORTANT NOTICE Texas Instruments (TI) reserves the right to make changes to its products or to
SYN113 Datasheet. ( MHz ASK Transmitter) Version 1.0
Datasheet (300 450MHz ASK Transmitter) Version 1.0 Contents 1. General Description... 1 2. Features... 1 3. Applications... 1 4. Typical Application... 2 5. Pin Configuration... 2 6. Pin Description...
CMT211xA Schematic and PCB Layout Design Guideline
AN101 CMT211xA Schematic and PCB Layout Design Guideline 1. Introduction The purpose of this document is to provide the guidelines to design a low-power CMT211xA transmitter with the maximized output power,
APPLICATION NOTE. ATA5279 Application Hints ATAN0003. Features. Description
APPLICATION NOTE ATA5279 Application Hints ATAN0003 Features General information Boost converter calculation and practical hints Antenna current regulation Oscillator aspects Description Most applications
TFT-LCD DC/DC Converter with Integrated Backlight LED Driver
TFT-LCD DC/DC Converter with Integrated Backlight LED Driver Description The is a step-up current mode PWM DC/DC converter (Ch-1) built in an internal 1.6A, 0.25Ω power N-channel MOSFET and integrated
THE SEQUEL COMMON SENSE OSCILLATOR TECHNIQUES, INTRODUCTION. changing the sometimes less than optimum oscillator design.
COMMON SENSE OSCILLATOR TECHNIQUES, THE SEQUEL INTRODUCTION Oscillator cells in ASICS have had a devastating effect on the sales of clock oscillators. Users have had the cost of clocking reduced at least
AN-1106 Custom Instrumentation Amplifier Design Author: Craig Cary Date: January 16, 2017
AN-1106 Custom Instrumentation Author: Craig Cary Date: January 16, 2017 Abstract This application note describes some of the fine points of designing an instrumentation amplifier with op-amps. We will
MP A, 55V, 100kHz Step-Down Converter with Programmable Output OVP Threshold
The Future of Analog IC Technology MP24943 3A, 55V, 100kHz Step-Down Converter with Programmable Output OVP Threshold DESCRIPTION The MP24943 is a monolithic, step-down, switch-mode converter. It supplies
Low-Jitter, Precision Clock Generator with Two Outputs
19-2456; Rev 0; 11/07 E V A L U A T I O N K I T A V A I L A B L E Low-Jitter, Precision Clock Generator Ethernet Networking Equipment General Description The is a low-jitter precision clock generator optimized
Features. Future Electronics (
/ ASB Embedding the wireless future.. Low-Cost SAW-stabilized surface mount OOK RF transmitter Typical Applications Remote Keyless Entry (RKE) Remote Lighting Controls On-Site Paging Asset Tracking Wireless
MK3727D LOW COST 24 TO 36 MHZ 3.3 VOLT VCXO. Description. Features. Block Diagram DATASHEET
DATASHEET MK3727D Description The MK3727D combines the functions of a VCXO (Voltage Controlled Crystal Oscillator) and PLL (Phase Locked Loop) frequency doubler onto a single chip. Used in conjunction
TA8435H/HQ TA8435H/HQ PWM CHOPPER-TYPE BIPOLAR STEPPING MOTOR DRIVER. FEATURES TOSHIBA BIPOLAR LINEAR INTEGRATED CIRCUIT SILICON MONOLITHIC
TOSHIBA BIPOLAR LINEAR INTEGRATED CIRCUIT SILICON MONOLITHIC TA8435H/HQ TA8435H/HQ PWM CHOPPER-TYPE BIPOLAR STEPPING MOTOR DRIVER. The TA8435H/HQ is a PWM chopper-type sinusoidal micro-step bipolar stepping
PCI-EXPRESS CLOCK SOURCE. Features
DATASHEET ICS557-01 Description The ICS557-01 is a clock chip designed for use in PCI-Express Cards as a clock source. It provides a pair of differential outputs at 100 MHz in a small 8-pin SOIC package.
Features. Haltronics Ltd (http://www.haltronicsltd.com/)
Embedding the wireless future.. Low-Cost SAW-stabilized surface mount OOK RF transmitter Typical Applications Remote Keyless Entry (RKE) Remote Lighting Controls On-Site Paging Asset Tracking Wireless
TLE4976-1K / TLE4976L
February 2009 / High Precision Hall Effect Switch with Current Interface Data Sheet Rev. 2.0 Sense & Control Edition 2009-02-12 Published by Infineon Technologies AG 81726 Munich, Germany 2009 Infineon
Features. Applications
105MHz Low-Power SOT23-5 Op Amp General Description The is a high-speed operational amplifier which is unity gain stable regardless of resistive and capacitive load. It provides a gain-bandwidth product
Understanding, measuring, and reducing output noise in DC/DC switching regulators
Understanding, measuring, and reducing output noise in DC/DC switching regulators Practical tips for output noise reduction Katelyn Wiggenhorn, Applications Engineer, Buck Switching Regulators Robert Blattner,
The CYF115 transmitter solution is ideal for industrial and consumer applications where simplicity and form factor are important.
CYF115 Datasheet 300M-450MHz RF Transmitter General Description The CYF115 is a high performance, easy to use, single chip ASK Transmitter IC for remote wireless applications in the 300 to 450MHz frequency