MEMS-based 3C accelerometers for land seismic acquisition: Is it time?
|
|
- Reynold Watkins
- 6 years ago
- Views:
Transcription
1 MEMS-based 3C accelerometers for land seismic acquisition: Is it time? DENIS MOUGENOT, Sercel, Carquefou Cedex, France NIGEL THORBURN, Sercel, Houston, Texas, U.S. Recent advances have allowed development of micro electro mechanical system (MEMS) sensors with the sensitivity, low noise, and dynamic range needed in seismic acquisition. This is a possible breakthrough because MEMS accelerometers have the potential to provide broader bandwidth, more accurate amplitude, and less sensitivity to planting tilt than the coil-based geophones that have long been used in the industry. Several papers have presented the advantages of threecomponent acquisition with single digital sensors based on MEMS, and the advent of these sensors has been promoted as the next big advance in land seismic acquisition much like the shift to 24-bits recording systems 10 years ago. So, this is a good time to ask an obvious question: Has this technology really advanced to the point that it can, or should, be used for general-purpose land seismic acquisition? This paper will attempt to answer that question by addressing the advantages and disadvantages for the general application of single 3C digital sensors. Why accelerometers for digital sensors? Ground motion can be measured as displacement, velocity, or acceleration. A mass/spring assembly is used for all these measurements. With a soft spring, the mass (the coil in the geophone) does not move and represents the reference for displacement or velocity measurements. With a stiff spring, the mass moves with the case, but with a small residual displacement related to the acceleration. This acceleration can be measured either by the strain on the spring (e.g., low cost, low power, high distortion air bags) or by a feedback force applied to the mass to cancel the displacement (e.g., high performance digital sensors requiring power supply). In this last implementation the sensor based on MEMS is still analog, while the control loop and the output provided by an application specific integrated chip (ASIC) are digital. Such a digital sensor is much smaller than the current standard. A MEMS accelerometer is a tiny silicon chip with a length of ~1 cm and weighing less than 1 g. A coil-based sensor is a cartridge with a length of 3 cm and weight of 76 g. Within the chip, the residual displacement between the inertial mass and the frame is on the order of a few nanometers, while the motion of a geophone coil may reach 2 mm. However, manufacturing such a digital sensor is expensive due to the cost of MEMS + ASIC. Therefore, actual recording in the field will use a single-sensor configuration (i.e., only one sensor per active channel). Comparison of MEMS-based sensors and coiled geophones. From the specification point of view, the essential benefit of MEMS accelerometers is a broadband linear amplitude and phase response that may extend from 0 (dc) to 800 Hz within 1% in amplitude and 20 ms in time (Figure 1). MEMS resonant frequency is far above the seismic band pass (1 khz). This makes it possible to record frequencies below 10 Hz without attenuation, including the direct current (dc) related to the gravity acceleration. The gravity vector provides a useful reference for sensitivity calibration and tilt measurement of Figure 1. Linear phase and amplitude response of a digital sensor unit (DSU) with MEMS compared with that of a 10-Hz geophone. The response is in the velocity domain for the geophone and in the acceleration domain for the DSU. 3C MEMS-based sensors that has no equivalent for geophones. Because acceleration increases with frequency (at constant velocity), MEMS accelerometers also are excellent for highfrequency measurements. In this domain (> 50 Hz) the floor/electric noise of the MEMS is lower than that of the equivalent geophone/station electronics. These broadband capabilities offer possible dramatic improvement in the vertical resolution of seismic data, which depends on the ratio between the maximum and minimum frequencies of the signal (Fmax/Fmin = 2 n, n being the number of octaves). A MEMS accelerometer is particularly suited for recording low frequency signals (< 5 Hz) like reflections at the main boundaries between lithological formations (or even earthquakes). In this frequency range, the limitation is more on the source side because such LF signals cannot be emitted with a sufficient S/N ratio. Recording of high frequencies is limited by their strong attenuation during propagation. However, MEMS sensors should be able, if close enough, to listen to microseismic events (~500 Hz) as fluids move in the reservoir during oil and gas production. The total dynamic range of a 24-bit recording system using MEMS can be up to 120 db (ratio between the floor noise at 4 ms sampling rate 4.5 µm/s 2 and the maximum signal 4.5 m/s 2 that can be recorded with less than -90 db distortion). It is lower than the total dynamic range of the same system using single geophones that should be up to 140 db (this is also the total dynamic range of the latest 24 bits recording systems). In practical situations (including the distortion generated by a strong signal or noise), the instantaneous dynamic range of a MEMS accelerometer (95 db) is much better than the one of a single geophone (no more than 70 db, but this may be improved by using groups of geophones). These differences in total and instantaneous dynamic ranges explain why a MEMS-based sensor is more suited to record a weak signal in presence of strong noise (near offsets) while a geophone (and even more a string of geophones) is more effective in recording a weak/deep reflection in presence of low noise (far offsets). 246 THE LEADING EDGE MARCH 2004 MARCH 2004 THE LEADING EDGE 0000
2 accelerometers. The advantages for the full digital transmission have already been checked. During field tests, records by bunched geophones were compared to MEMS sensors at the same location (Figure 3). 50 Hz (picked up below a high voltage line) is obvious on the shotpoint recorded by bunched phones. On the corresponding f-k diagram, the electromagnetic noise interferes strongly with signal. This noise does not occur on any of the three components of the MEMS sensors due to the full digital transmission. Figure 2. In the first digital recording system (top), all transmissions between geophone groups and central unit, including the A/D converter, were analog. About 30 years later (center), only transmission between geophone groups and the field digitizing unit (FDU) was analog. Today (bottom), the digital sensor unit (DSU) makes possible full digital transmission. Figure 3. Shotpoint comparison between the vertical component of a digital sensor unit (DSU3) and bunched phones planted at the same location (photo). Strong pick up of a high voltage line is due to analog transmission up to the station electronics. The f-k diagram shows this 50- Hz noise interfere with signal. DSU data are not contaminated. (Data courtesy of BatchNeftGeofisika) Amplitude calibration of a MEMS sensor and its stability over aging and temperature variations are better than that of traditional geophones. Overall, the performance of a digital sensor, in which MEMS are integrated with the station electronics in a single housing, is better than conventional station electronics that is connected during the same survey to different strings of geophones of variable characteristics. The full digital transmission. In the early 1970s, the A/D converter of the first digital recording system was implemented in the central unit. One analog pair of wires for each channel was used for transmission between strings of geophones and the recording truck (Figure 2). Noise from electromagnetic interference, signal cross-talk, and sensitivity to leakage were common. About 30 years later, the electronics distributed in the seismic network provided digitization close to the geophone groups. Only two pairs of wires are necessary for telemetric transmission of or more channels in real time. Sensitivity to leakage is reduced and the digital data are controlled by each node of the seismic network (and, thus, may be retransmitted if necessary). However, noise pick may still contaminate the analog signals transmitted through the strings of geophones. This should disappear with the integration of the sensor with the station electronics as it is done with the MEMS Digital sensors to replace arrays of geophones? Arrays of geophones may tremendously improve the dynamic range of a receiver point by reducing ambient and coherent noise. Compared to a single geophone, an array of N geophones, whether connected in series or in parallel, improves the dynamic range by 10 logn db, as the ambient noise is reduced by the square root of N. For attenuation of coherent noise, geophones are laid out in a spatial pattern that provides array filtering. The size of the array and the number of wired geophones should be large enough to properly sample the maximum wavelength of the ground roll. Despite these advantages, field geophysicists would like to get rid of arrays because they are large and heavy and, as a result, slow crew productivity and require expensive logistics. At first glance, the use of single digital sensors would have many operational and geophysical advantages over geophone arrays. Layout and positioning are easier than with geophone strings, and this is even more relevant for 3C receiver points. Recording is isotropic (no azimuth-dependent array filtering), and the high frequency content of the signal is not attenuated by intra-array statics (particularly in S-wave recording). However, these benefits are only true in an ideal world where reflected signal is not contaminated by noise i.e., in a situation where a single coiled geophone would have been sufficient. In the field, the spacing of single sensors should decrease with respect to the length of a geophone array. This shorter spacing will not attenuate noise while recording, but it will provide enough multiplicity (fold coverage) to decrease the ambient noise while stacking data. Denser spatial sampling also prevents the coherent noise from aliasing. Therefore, we cannot expect to get better looking shotpoint displays while recording with single digital sensors. The benefits (larger frequency content, more accurate amplitude) will only show up with the final sections, after data processing. New requirements for acquisition geometry. In practice, how many MEMS sensors would be necessary to replace a string of N geophones? It is unlikely that anyone will record as many single digital sensors as hard-wired geophones, and it is probably not necessary, even though that would provide excellent noise attenuation. Let us consider ground roll (GR), often the strongest noise. In this case, the digital sensor spacing D should be 0000 THE LEADING EDGE MARCH 2004 MARCH 2004 THE LEADING EDGE 247
3 Figure 7. Real time display of three-component digital sensor shot points (Z and X components) in the doghouse after velocity conversion and lowcut (10 Hz) filtering. (Data courtesy of Veritas DGC and Devon) Figure 4. Shotpoint (GR = ground roll, BS = backscattering) with 10-m spacing between single digital sensors. On the f-k diagram, GR is aliased and interferes with signal. (Data courtesy of CGG) Figure 8. Comparison of PP and PS final sections corresponding to the previous SPs. The PS section is squeezed to PP time by assuming constant V P /V S = 3. The frequency content of the PP section is above 200 Hz; in the PS section, frequencies above 70 Hz have been attenuated. The reflectivity of the two sections recorded in sand/shale formations is quite different. (Data courtesy of Veritas DGC and Devon) Figure 5. Shotpoint with 3.3 m spacing between single digital sensors. On the f-k diagram, GR is still aliased but does not interfere with signal. (Data courtesy of CGG) Figure 6. 2D acquisition design that uses a corridor of 1C single digital sensor units connected along parallel telemetric cables. At a given receiver point (RP) different types of digital groups (DG1, DG2) may be considered to reduce ambient noise and filter the ground roll. such that the GR wavelength L = Va/Fa (Va = apparent velocity, Fa = apparent frequency) will be sampled at least two times (i.e., D = Va/2Fa). This often provides values in the range of 3 to 30 m. Figures 4 and 5 compare f-k diagrams of two SPs recorded at the same location with different spatial sampling. At 10-m spacing, the very low velocity ground roll (330 m/s which is as low as the air blast) is aliased and interferes with signal. At 3.33-m spacing, GR is still aliased but it vanishes at high frequencies (70 Hz) before intersecting the signal. Considering this maximum frequency limitation of the noise it is possible to adequately sample with a spacing a little more than half of the GR wavelet, as suggested by Baeten et al. (2000). Up to now, we have considered only 2D propagation. With 3D acquisition or complex near-surface-generated backscattered noise, it would be necessary to sample the noise properly both in the inline and crossline directions. Such areal sampling would require a corridor of single digital sensors equivalent to the patches of hard-wired geophones. Since digital sensors are directly connected to a telemetry cable, deployment of such receiver line would require several parallel cables (Figure 6) instead of only one telemetry cable for all geophones. A quick calculation of the channel requirement for a 3D swath of 4 4 km 2 with 100 m between receiver lines (each having five individual cables with single digital sensors at 10-m spacing) produces a figure of active channels. This amount is still beyond the realtime capability of all recording systems at 2 ms sampling. Today, this type of single sensor arrangement is only compatible with a 2D acquisition. Due to the continuous spatial sampling, this corridor of single sensors provides a sort of 2D universal acquisition design. Different single sensor combinations, often referred as digital group forming, may be used to attenuate noise after recording by all single digital sensors. Since groups overlap from point-to-point, each single sensor may be used in different digital groups. At a given receiver point, this group forming may even involve time-dependent digital arrays since S/N ratio decreases as traveltime increases. A new era for 3C recording. Connecting strings of threecomponent geophones (triphones) to a telemetry cable involves heavy equipment, lots of wire, and many connectors. With standard equipment, planting, leveling, and properly orienting these triphones is painful but 248 THE LEADING EDGE MARCH 2004 MARCH 2004 THE LEADING EDGE 0000
4 Figure 10. Real time QC of a shotpoint (Z component) coming from digital sensor units and conventional geophone strings (FDU) laid out at the same location and recorded by the same central unit. For visual comparison it is possible in real time to integrate acceleration data into the velocity domain, and to apply low cut filtering to mimic geophone data. Figure 9. Back-to-back comparison of a 408UL station electronics (FDU) that should be connected to a string of geophones with a 408UL 3C digital sensor unit (DSU3) that includes three sensors with the corresponding electronics. Base assembly to the telemetry line is the same to switch easily from analog to digital sensors. mandatory. The final output is the electric sum of all triphones connected to the same station electronics and any correction is impossible at a later stage. Having sensors and station electronics integrated in the same housing will reduce overall weight and wiring errors, and should make all multicomponent surveys faster, better, and cheaper. Of course, planting a 3C digital sensor would need some attention to get the proper coupling, but ensuring its exact verticality is not mandatory. This is because of a unique feature of the MEMS-based 3C digital sensor its ability to measure the continuous effect of the gravity vector. This vector is used as a reference to automatically compute with high accuracy (±0.5 ) the tilt of each horizontal sensor. These tilt values are stored in the trace header extensions, and data may be even corrected for tilt in real time by the central unit. Sensor orientation may be corrected, if necessary, during processing by assuming a radial propagation between the source and the single sensor (3D surveys only). Tilt measurement is only one aspect of the advantages provided, in terms of vector fidelity, by the MEMS-based 3C digital sensors. Their broadband capabilities (0-800 Hz linear response), the very precise orthogonality of the sensors (±0.25 accuracy) and the accurate and stable amplitude calibration (±0.25% accuracy) will improve overall quality of 3C seismic data. Many surveys have already field proven this 3C digital sensor technology. Data in Figures 7 and 8, from a 2D acquisition recorded with explosives in North America, demonstrate the broadband capabilities of the MEMS 3C digital sensor. High frequency preservation while stacking has required careful static definition and efficient deconvolution after noise attenuation. On the final PP section, the frequency spectrum of the signal in a s window is above 200 Hz, and signal beyond 300 Hz is evident down to 0.2 s. Crew productivity with single 3C digital sensors. Seismic data acquisition with high-density single digital sensors will require recording a large number of channels. Short receiver point spacing to get adequate noise sampling may double (or more) the number of channels. Three components instead of one will triple the number of channels. For 3D surveys, this may mean tens of thousands of channels. To maintain productivity with a such high channel count, the ground equipment must be light, and the acquisition system low power. Transmission redundancy should be available thanks to multipath telemetry, and real-time quality control of the spread and of the seismic data should be available for quick quality control. As implemented in the 408UL recording system (Figure 9), the 580 g of a 3C digital sensor unit (including the base assembly with the telemetry cable, all station electronics for the three channels and the three MEMS sensors) compares favorably with the 450 g of the 1C field digitizing unit (including the same base assembly and the electronics for only one channel to be connected to a string of geophones). This comparison illustrates the high level of sensor/electronics integration that MEMS accelerometers makes it possible. Considering costs associated with manpower and health/safety/environmental issues related to the use of vehicles, a seismic crew should use the smallest number of batteries and use each to its maximum duration (i.e., the recording system must be low power). Even the fact that MEMS require some power while the geophone does not is not a disadvantage for digital sensor recording. At least with the 408UL recording system, the overall consumption of a three-component digital sensor (400 mw) is less than the equivalent consumption of three field digitizing units connected to triphones (420 mw). Distributed electronics with computing and buffering capabilities as implemented in the most advanced telemetry cable systems makes it possible to secure data transmission. In case of a cable failure, the use of multiple transverses between the receiver lines and the central units will permit the seismic network to reroute data through a different path. As the number of channels increases up to and beyond, manual or visual checking of the entire system and data quality becomes impossible. This explains the importance of automated real-time quality control as already implemented for single digital sensor recording. For example, the tilt measured from the residual dc on the horizontal components can be checked continuously. The result is stored numerically and also displayed graphically with a warning color if tilt is above a predefined threshold. In addition each MEMS sensor includes a built-in reference accelerometer that provides a continuous tracking of such factors as distortion, gain, phase, and cross-talk. During the recording, the data may be visualized component by component (Figure 7); several attributes (e.g., signal, noise, frequency content, faulty trace) are available on a trace-by-trace or shot-by-shot basis which allows continuous monitoring of the acquisition process. Since MEMS sensors record acceleration and not velocity, real time integration from one domain to the other has been made available. To provide a one-to-one comparison 0000 THE LEADING EDGE MARCH 2004 MARCH 2004 THE LEADING EDGE 249
5 between analog and digital sensors, MEMS broadband seismic data may be filtered to resemble geophone data (10 Hz low cut filtering and damping, Figure 10). Conclusion. Is it time to use digital sensors? MEMS-based single digital sensors offer new capabilities compared with conventional arrays of geophones. The sensor itself (MEMS + ASIC) should provide better vector fidelity thanks to its accurate and stable calibration (amplitude and orthogonality), and its broadband linear response (from dc to 800 Hz). Tight integration of the sensor with the station electronics allows size/weight reduction and lower power consumption. Such a sensor will provide, for the first time, complete digital transmission, from the sensor to the central unit, which is less sensitive to electromagnetic pick-up, cross-talk, and leakage. Overall MEMS technology offers the potential to reduce costs while improving data quality. However, there are two limitations to the use of MEMS sensors: one is geophysical (digital sensors are recorded as single sensors) and the other is economic (manufacturing costs of MEMS compared to coiled geophones). If single-sensor recording provides obvious advantages for deployment and signal preservation, these benefits are strongly balanced by the inability of single sensors to attenuate any ambient or shot-related noise. Records by single digital sensors will be dominated by noise, and this domination will be even worse if point receivers are used in conjunction with point source (i.e., without any source array filtering). In noisy areas with strong, dispersive, and backscattered ground roll and with high ambient noise this may prevent recording any usable signal. To be able to recover signal, all this noise should be attenuated during processing. For ambient noise reduction, the fold coverage should increase. This is possible by decreasing the spacing and increasing the number of single digital sensors. For coherent noise attenuation, the point receiver spacing should also decrease, perhaps not down to the geophone spacing, but at least down to the Nyquist distance necessary to keep the corresponding ground-roll unaliased. For both ambient and coherent noise, this implies increasing the number of point receivers and channel capabilities (which will increase the cost of acquiring data). Thus a question arises: Does it make sense to invest and operate single digital sensors instead of conventional geophone arrays? both good PP-wave data as well as good PS-wave data. In some surveys, crews are deploying lines of 3C MEMSbased sensors strategically within a 3D layout of analog phones (1C) recorded on the same system at the same time. In this way P-wave sampling and S-wave sampling can be different on the same survey, moving closer to optimum spacing for specific wavefields. This is only one example of the creativity of system manufacturers, their customers, and their customer s clients when new technology offers new solutions to pressing exploration and production problems. So, is it time for MEMS-based sensors? Why not! In this industry we have always had exploration or production problems that we couldn t solve with existing technology. So we look for the next technology with which we can push the envelope. Successful and efficient use of MEMS-based sensors is a reality. TLE Acknowledgments: We thank CGG, Veritas DGC, Devon, and BatchNeftGeofisika for having acquired and processed the digital sensor data shown in this article. We thank Sercel s R&D department for useful information, and Sercel s engineers who supervised the field tests. Final review by Bob Albers and George Wood was very helpful. Corresponding author: denis.mougenot@sercel.fr Is it time? In all realms of seismic recording, single sensor acquisition, done properly, has the potential to increase data resolution to the levels required for the definition of subtle targets and detection of small changes. When 120 db recording became a reality there was a lot of talk about the geophysical benefits of this new range of seismic data. There is also a lot of discussion that up to now we have really not ever used this breakthrough in the actual processing and interpretation of the data. In the single sensor world, we will now require dynamic ranges every bit as wide as these new systems allow. We have discussed sampling for single sensor acquisition and know that better sampling with higher channel counts will be required. When we consider the different wavelengths associated with P-wave data and S-wave data, the sampling requirements of the recording layout become more complicated than when we strictly consider a P-wave survey. At this time there are crews in the field using single sensor MEMS-based systems to record 3D-3C with improved but still practical spatial sampling. These crews are recording 250 THE LEADING EDGE MARCH 2004 MARCH 2004 THE LEADING EDGE 0000
DSU3-428 DIGITAL SENSOR UNITS
DSU3-428 DIGITAL SENSOR UNITS DSU3-428 The 428XL offers all new hardware and software which is specifi cally designed to address the growing demands of the geophysical industry for even larger channel
More informationMEMS-based accelerometers: expectations and practical achievements
first break volume 29, February 2011 MEMS-based accelerometers: expectations and practical achievements Denis Mougenot, 1* Anatoly Cherepovskiy 1 and Liu JunJie 1 trace the development of MEMS sensors
More informationSouth Africa CO2 Seismic Program
1 South Africa CO2 Seismic Program ANNEXURE B Bob A. Hardage October 2016 There have been great advances in seismic technology in the decades following the acquisition of legacy, limited-quality, 2D seismic
More informationThe case for longer sweeps in vibrator acquisition Malcolm Lansley, Sercel, John Gibson, Forest Lin, Alexandre Egreteau and Julien Meunier, CGGVeritas
The case for longer sweeps in vibrator acquisition Malcolm Lansley, Sercel, John Gibson, Forest Lin, Alexandre Egreteau and Julien Meunier, CGGVeritas There is growing interest in the oil and gas industry
More informationImprovement of signal to noise ratio by Group Array Stack of single sensor data
P-113 Improvement of signal to noise ratio by Artatran Ojha *, K. Ramakrishna, G. Sarvesam Geophysical Services, ONGC, Chennai Summary Shot generated noise and the cultural noise is a major problem in
More informationTh ELI1 08 Efficient Land Seismic Acquisition Sampling Using Rotational Data
Th ELI1 8 Efficient Land Seismic Acquisition Sampling Using Rotational Data P. Edme* (Schlumberger Gould Research), E. Muyzert (Sclumberger Gould Research) & E. Kragh (Schlumberger Gould Research) SUMMARY
More informationThere is growing interest in the oil and gas industry to
Coordinated by JEFF DEERE JOHN GIBSON, FOREST LIN, ALEXANDRE EGRETEAU, and JULIEN MEUNIER, CGGVeritas MALCOLM LANSLEY, Sercel There is growing interest in the oil and gas industry to improve the quality
More informationAnthony Chu. Basic Accelerometer types There are two classes of accelerometer in general: AC-response DC-response
Engineer s Circle Choosing the Right Type of Accelerometers Anthony Chu As with most engineering activities, choosing the right tool may have serious implications on the measurement results. The information
More informationThis presentation was prepared as part of Sensor Geophysical Ltd. s 2010 Technology Forum presented at the Telus Convention Center on April 15, 2010.
This presentation was prepared as part of Sensor Geophysical Ltd. s 2010 Technology Forum presented at the Telus Convention Center on April 15, 2010. The information herein remains the property of Mustagh
More informationSummary. Theory. Introduction
round motion through geophones and MEMS accelerometers: sensor comparison in theory modeling and field data Michael Hons* Robert Stewart Don Lawton and Malcolm Bertram CREWES ProjectUniversity of Calgary
More informationUsing long sweep in land vibroseis acquisition
Using long sweep in land vibroseis acquisition Authors: Alexandre Egreteau, John Gibson, Forest Lin and Julien Meunier (CGGVeritas) Main objectives: Promote the use of long sweeps to compensate for the
More informationCHOOSING THE RIGHT TYPE OF ACCELEROMETER
As with most engineering activities, choosing the right tool may have serious implications on the measurement results. The information below may help the readers make the proper accelerometer selection.
More informationTh-P08-11 Deblending of Single Source Vibroseis Land Data in Egypt with V1 Noise Attenuation Algorithm
Th-P08-11 Deblending of Single Source Vibroseis Land Data in Egypt with V1 Noise Attenuation Algorithm N. Gulunay* (CGG), E. Shaker (CGG), A. Karagul (CGG), A. Ramadan (CGG), T. Bianchi (CGG), J. Ross
More informationLow wavenumber reflectors
Low wavenumber reflectors Low wavenumber reflectors John C. Bancroft ABSTRACT A numerical modelling environment was created to accurately evaluate reflections from a D interface that has a smooth transition
More informationComparisons between data recorded by several 3-component coil geophones and a MEMS sensor at the Violet Grove monitor seismic survey
Geophone and sensor comparisons Comparisons between data recorded by several 3-component coil geophones and a MEMS sensor at the Violet Grove monitor seismic survey Don C. Lawton, Malcolm B. Bertram, Gary
More informationSeaRay 428. Specifications. Shipboard Equipment GLOBAL ARCHITECTURE RECORDING (BASIC CONFIGURATION)
SeaRay 428 Specifications GLOBAL ARCHITECTURE Lightweight, flexible cable and electronic modules that operate to a depth of: SeaRay 300: 300 m use down to 500 m with restrictions SeaRay 100: 100 m (smaller
More informationPolarization Filter by Eigenimages and Adaptive Subtraction to Attenuate Surface-Wave Noise
Polarization Filter by Eigenimages and Adaptive Subtraction to Attenuate Surface-Wave Noise Stephen Chiu* ConocoPhillips, Houston, TX, United States stephen.k.chiu@conocophillips.com and Norman Whitmore
More informationEvaluation of 3C sensor coupling using ambient noise measurements Summary
Evaluation of 3C sensor coupling using ambient noise measurements Howard Watt, John Gibson, Bruce Mattocks, Mark Cartwright, Roy Burnett, and Shuki Ronen Veritas Geophysical Corporation Summary Good vector
More informationSIGMA-DELTA CONVERTER
SIGMA-DELTA CONVERTER (1995: Pacífico R. Concetti Western A. Geophysical-Argentina) The Sigma-Delta A/D Converter is not new in electronic engineering since it has been previously used as part of many
More informationTitleApplication of MEMS accelerometer t. AIZAWA, Takao; KIMURA, Toshinori; M Toshifumi; TAKEDA, Tetsuya; ASANO,
TitleApplication of MEMS accelerometer t Author(s) AIZAWA, Takao; KIMURA, Toshinori; M Toshifumi; TAKEDA, Tetsuya; ASANO, Citation International Journal of the JCRM ( Issue Date 2008-12 URL http://hdl.handle.net/2433/85166
More informationAVO processing of walkaway VSP data at Ross Lake heavy oilfield, Saskatchewan
AVO processing of walkaway VSP data at Ross Lake heavy oilfield, Saskatchewan Zimin Zhang, Robert R. Stewart, and Don C. Lawton ABSTRACT The AVO processing and analysis of walkaway VSP data at Ross Lake
More informationGeophones // A COMPLETE PRODUCT LINE. Sercel has a long history in being at the forefront of developing
Geophones SG-5 // A COMPLETE PRODUCT LINE Sercel has a long history in being at the forefront of developing new cutting-edge technology. Setting new standards for sensors is no exception. Our advanced
More informationDevelopments in vibrator control
Geophysical Prospecting, 2010, 58, 33 40 doi: 10.1111/j.1365-2478.2009.00848.x Developments in vibrator control D. Boucard and G. Ollivrin Sercel France, PO Box 439, 44474 Carquefou Cedex, France Received
More informationMulticomponent seismic polarization analysis
Saul E. Guevara and Robert R. Stewart ABSTRACT In the 3-C seismic method, the plant orientation and polarity of geophones should be previously known to provide correct amplitude information. In principle
More informationProcessing the Blackfoot broad-band 3-C seismic data
Processing the Blackfoot broad-band 3-C seismic data Processing the Blackfoot broad-band 3-C seismic data Stan J. Gorek, Robert R. Stewart, and Mark P. Harrison ABSTRACT During early July, 1995, a large
More informationSurvey results obtained in a complex geological environment with Midwater Stationary Cable Luc Haumonté*, Kietta; Weizhong Wang, Geotomo
Survey results obtained in a complex geological environment with Midwater Stationary Cable Luc Haumonté*, Kietta; Weizhong Wang, Geotomo Summary A survey with a novel acquisition technique was acquired
More informationAir-noise reduction on geophone data using microphone records
Air-noise reduction on geophone data using microphone records Air-noise reduction on geophone data using microphone records Robert R. Stewart ABSTRACT This paper proposes using microphone recordings of
More informationw w w. s e i s m i c i n s t r u m e n t s. c o m Page 1
w w w. s e i s m i c i n s t r u m e n t s. c o m Page 1 Seismic Instruments offers three different configurations of data acquisition system (Cabled, Cable-Free and Mixed) in a wide range of options,
More informationSmartSenseCom Introduces Next Generation Seismic Sensor Systems
SmartSenseCom Introduces Next Generation Seismic Sensor Systems Summary: SmartSenseCom, Inc. (SSC) has introduced the next generation in seismic sensing technology. SSC s systems use a unique optical sensing
More informationProcessing the Teal South 4C-4D seismic survey
Processing the Teal South 4C-4D seismic survey Carlos Rodriguez-Suarez, Robert R. Stewart and Han-Xing Lu Processing the Teal South 4C-4D ABSTRACT Repeated 4C-3D seismic surveys have been acquired over
More informationTu N Higher Vibrator Hydraulic Force for Improved High Frequency Generation
Tu N105 06 Higher Vibrator Hydraulic Force for Improved High Frequency Generation N. Tellier* (Sercel), G. Ollivrin (Sercel) & G. Caradec (Sercel) SUMMARY For conventional deep seismic with heavy vibrators,
More informationSeismic Reflection Method
1 of 25 4/16/2009 11:41 AM Seismic Reflection Method Top: Monument unveiled in 1971 at Belle Isle (Oklahoma City) on 50th anniversary of first seismic reflection survey by J. C. Karcher. Middle: Two early
More informationEfficient Acquisition of Quality Borehole Seismic
Efficient Acquisition of Quality Borehole Seismic The Versatile Seismic Imager Applications Integrated processing for interpretation of boreholeand surface-seismic data Images for reservoir definition
More informationAdaptive f-xy Hankel matrix rank reduction filter to attenuate coherent noise Nirupama (Pam) Nagarajappa*, CGGVeritas
Adaptive f-xy Hankel matrix rank reduction filter to attenuate coherent noise Nirupama (Pam) Nagarajappa*, CGGVeritas Summary The reliability of seismic attribute estimation depends on reliable signal.
More informationTu A D Broadband Towed-Streamer Assessment, West Africa Deep Water Case Study
Tu A15 09 4D Broadband Towed-Streamer Assessment, West Africa Deep Water Case Study D. Lecerf* (PGS), D. Raistrick (PGS), B. Caselitz (PGS), M. Wingham (BP), J. Bradley (BP), B. Moseley (formaly BP) Summary
More informationGeophysical Applications Seismic Reflection Surveying
Seismic sources and receivers Basic requirements for a seismic source Typical sources on land and on water Basic impact assessment environmental and social concerns EPS435-Potential-08-01 Basic requirements
More informationA robust x-t domain deghosting method for various source/receiver configurations Yilmaz, O., and Baysal, E., Paradigm Geophysical
A robust x-t domain deghosting method for various source/receiver configurations Yilmaz, O., and Baysal, E., Paradigm Geophysical Summary Here we present a method of robust seismic data deghosting for
More informationAuto-levelling geophone development and testing
Auto-levelling geophone development Auto-levelling geophone development and testing Malcolm B. Bertram, Eric V. Gallant and Robert R. Stewart ABSTRACT An auto-levelling, motion sensor (multi-component
More information2012 SEG SEG Las Vegas 2012 Annual Meeting Page 1
Full-wavefield, towed-marine seismic acquisition and applications David Halliday, Schlumberger Cambridge Research, Johan O. A. Robertsson, ETH Zürich, Ivan Vasconcelos, Schlumberger Cambridge Research,
More informationOPTIMIZING HIGH FREQUENCY VIBROSEIS DATA. Abstract
OPTIMIZING HIGH FREQUENCY VIBROSEIS DATA Theresa R. Rademacker, Kansas Geological Survey, Lawrence, KS Richard D. Miller, Kansas Geological Survey, Lawrence, KS Shelby L. Walters, Kansas Geological Survey,
More informationNoise Reduction in VibroSeis Source Kaëlig Castor*, Thomas Bianchi, Olivier Winter, Thierry Klein, CGG
Downloaded //6 to 9..7.. Redistribution subject to SEG license or copyright; see Terms of Use at http://library.seg.org/ Noise Reduction in VibroSeis Source Kaëlig Castor*, Thomas Bianchi, Olivier Winter,
More informationT17 Reliable Decon Operators for Noisy Land Data
T17 Reliable Decon Operators for Noisy Land Data N. Gulunay* (CGGVeritas), N. Benjamin (CGGVeritas) & A. Khalil (CGGVeritas) SUMMARY Interbed multiples for noisy land data that survives the stacking process
More informationSummary. Time only. Distance only. Simultaneous Methods. Distance and Time. Slip-Sweeps Dynamic Slip-Sweeps Unconstrained simultaneous sources
Over 40,000 VPs per day with real-time quality control: Opportunities and Challenges Peter I. Pecholcs, Stephen K. Lafon, Hafiz Al-Shammery and Panos G. Kelamis (Saudi Aramco) Olivier Winter, Jean-Baptiste
More informationAbstract. Key words: digital geophone, Jizhong depression, tight marl oil exploration, phase consistency, frequency. Introduction
Bai Xuming, Yuan Shenghu, Wang Zedan, Chen Jingguo, Wang Xiaodong and Hu Qing, BGP, CNPC Abstract Geophone is one of the key equipment for seismic data acquisition and the quality of seismic data for prospecting
More informationRadial Gain and its Advantages in Seismic Data Acquisition
P-162 Radial Gain and its Advantages in Seismic Data Acquisition M. Polaiah*, ONGC Ltd. Summary This paper explains the theory behind the radial gain and fixing of the parameters for applying radial gain
More informationModal Excitation. D. L. Brown University of Cincinnati Structural Dynamics Research Laboratory. M. A. Peres The Modal Shop, Inc Cincinnati, OH
Modal Excitation D. L. Brown University of Cincinnati Structural Dynamics Research Laboratory M. A. Peres The Modal Shop, Inc Cincinnati, OH IMAC-XXVI, Modal Excitation, #356, Feb 04, 2008, Intoduction
More informationSeismic reflection method
Seismic reflection method Seismic reflection method is based on the reflections of seismic waves occurring at the contacts of subsurface structures. We apply some seismic source at different points of
More information25823 Mind the Gap Broadband Seismic Helps To Fill the Low Frequency Deficiency
25823 Mind the Gap Broadband Seismic Helps To Fill the Low Frequency Deficiency E. Zabihi Naeini* (Ikon Science), N. Huntbatch (Ikon Science), A. Kielius (Dolphin Geophysical), B. Hannam (Dolphin Geophysical)
More informationField Tests of 3-Component geophones Don C. Lawton and Malcolm B. Bertram
Field Tests of 3-Component geophones Don C. Lawton and Malcolm B. Bertram ABSTRACT Field tests of Litton, Geosource and Oyo 3-component geophones showed similar performance characteristics for all three
More informationRadial trace filtering revisited: current practice and enhancements
Radial trace filtering revisited: current practice and enhancements David C. Henley Radial traces revisited ABSTRACT Filtering seismic data in the radial trace (R-T) domain is an effective technique for
More informationCapacitive Versus Thermal MEMS for High-Vibration Applications James Fennelly
Capacitive Versus Thermal MEMS for High-Vibration Applications James Fennelly Design engineers involved in the development of heavy equipment that operate in high shock and vibration environments need
More informationMEAS Silicon MEMS Piezoresistive Accelerometer and its Benefits
MEAS Silicon MEMS Piezoresistive Accelerometer and its Benefits Piezoresistive Accelerometers 1. Bonded Strain Gage type (Gages bonded to metal seismic mass using epoxy) Undamped circa 1950 s Fluid (oil)
More informationAttenuation of high energy marine towed-streamer noise Nick Moldoveanu, WesternGeco
Nick Moldoveanu, WesternGeco Summary Marine seismic data have been traditionally contaminated by bulge waves propagating along the streamers that were generated by tugging and strumming from the vessel,
More informationCOMPACT MOLECULAR-ELECTRONIC SEISMIC SENSORS
COMPACT MOLECULAR-ELECTRONIC SEISMIC SENSORS Molecular-electronic seismic accelerometers and velocimeters are designed for measuring seismic vibrations of the ground surface, buildings and engineering
More informationThis tutorial describes the principles of 24-bit recording systems and clarifies some common mis-conceptions regarding these systems.
This tutorial describes the principles of 24-bit recording systems and clarifies some common mis-conceptions regarding these systems. This is a general treatment of the subject and applies to I/O System
More informationFINAL REPORT EL# RS. C. A. Hurich & MUN Seismic Team Earth Sciences Dept. Memorial University Sept. 2009
FINAL REPORT EL# 09-101-01-RS MUNSIST Seismic Source Test - Five Mile Road C. A. Hurich & MUN Seismic Team Earth Sciences Dept. Memorial University Sept. 2009 1 EL# 09-101-01-RS Five-Mile Road Memorial
More informationHunting reflections in Papua New Guinea: early processing results
Hunting reflections in Papua New Guinea: early processing results David C. Henley and Han-Xing Lu PNG processing ABSTRACT Papua New Guinea is among the most notoriously difficult areas in the world in
More informationVibration and air pressure monitoring of seismic sources
Vibration monitoring of seismic sources Vibration and air pressure monitoring of seismic sources Alejandro D. Alcudia, Robert R. Stewart, Nanna Eliuk* and Rick Espersen** ABSTRACT Vibration monitoring
More informationMethods for reducing unwanted noise (and increasing signal) in passive seismic surveys
Methods for reducing unwanted noise (and increasing signal) in passive seismic surveys Tim Dean* Aidan Shem Mus ab Al Hasani Curtin University Curtin University Curtin University Bentley, West Australia
More informationProgress in DAS Seismic Methods
Progress in DAS Seismic Methods A. Mateeva, J. Mestayer, Z. Yang, J. Lopez, P. Wills 1, H. Wu, W. Wong, Barbara Cox (Shell International Exploration and Production, Inc.), J. Roy, T. Bown ( OptaSense )
More informationEvaluation of a broadband marine source
Evaluation of a broadband marine source Rob Telling 1*, Stuart Denny 1, Sergio Grion 1 and R. Gareth Williams 1 evaluate far-field signatures and compare processing results for a 2D test-line acquired
More informationP E R F O R M A N C E D E P E N D A B I L I T Y A V A I L A B I L I T Y
PeakVelocity in Octave Bandwidth (db wrt 1m 2 /s 2 ) 0-25 -50-75 -100-125 -150-175 -200-225 -250 The Earthquake Spectrum Local events ~10 km Several seconds to 30 Hz Regional ~100 km 30 seconds to 10 Hz
More informationWS15-B02 4D Surface Wave Tomography Using Ambient Seismic Noise
WS1-B02 4D Surface Wave Tomography Using Ambient Seismic Noise F. Duret* (CGG) & E. Forgues (CGG) SUMMARY In 4D land seismic and especially for Permanent Reservoir Monitoring (PRM), changes of the near-surface
More informationGlobal Seismic Network Design Goals Update 2002
Global Seismic Network Design Goals Update 2002 August 26, 2002 GSN ad hoc Design Goals Subcommittee Thorne Lay, Chair Jon Berger Ray Buland Rhett Butler Goran Ekstrom Bob Hutt Barbara Romanowicz 1 Introduction
More informationVibration studies of a superconducting accelerating
Vibration studies of a superconducting accelerating module at room temperature and at 4.5 K Ramila Amirikas, Alessandro Bertolini, Wilhelm Bialowons Vibration studies on a Type III cryomodule at room temperature
More informationISSN Volume 28 Issue 6 June A New Spring for Geoscience. Special Topic
ISSN 0263-5046 Volume 28 Issue 6 June 2010 Special Topic Technical Articles Multi-azimuth processing and its applications to wide-azimuth OBC seismic data offshore Abu Dhabi Borehole image logs for turbidite
More informationI017 Digital Noise Attenuation of Particle Motion Data in a Multicomponent 4C Towed Streamer
I017 Digital Noise Attenuation of Particle Motion Data in a Multicomponent 4C Towed Streamer A.K. Ozdemir* (WesternGeco), B.A. Kjellesvig (WesternGeco), A. Ozbek (Schlumberger) & J.E. Martin (Schlumberger)
More informationBorehole Seismic Processing Summary Checkshot Vertical Seismic Profile
Borehole Seismic Processing Summary Checkshot Vertical Seismic Profile COMPANY: Gaz de France WELL: G 14-5 RIG: Noble G.S. FIELD: G 14 LOGGING DATE: COUNTRY: Ref. no: 10-MAR-2005 The Netherlands, Off shore
More informationDownloaded 09/04/18 to Redistribution subject to SEG license or copyright; see Terms of Use at
Processing of data with continuous source and receiver side wavefields - Real data examples Tilman Klüver* (PGS), Stian Hegna (PGS), and Jostein Lima (PGS) Summary In this paper, we describe the processing
More informationDesinging of 3D Seismic Survey And Data Processing of Abu Amood Oil Field Southern of Iraq
Desinging of 3D Seismic Survey And Data Processing of Abu Amood Oil Field Southern of Iraq Salman Z. Khorshid, Ahmed I. Khaleel Dept.Geology, College of Science, Univercity of Baghdad Abstract 3D seismic
More informationEENG473 Mobile Communications Module 3 : Week # (12) Mobile Radio Propagation: Small-Scale Path Loss
EENG473 Mobile Communications Module 3 : Week # (12) Mobile Radio Propagation: Small-Scale Path Loss Introduction Small-scale fading is used to describe the rapid fluctuation of the amplitude of a radio
More informationSummary. Page SEG SEG Denver 2014 Annual Meeting
Seismo-acoustic characterization of a seismic vibrator Claudio Bagaini*, Martin Laycock and Colin Readman, WesternGeco; Emmanuel Coste, Schlumberger; Colin Anderson, Siemens PLM Software Summary A seismic
More informationInterferometric Approach to Complete Refraction Statics Solution
Interferometric Approach to Complete Refraction Statics Solution Valentina Khatchatrian, WesternGeco, Calgary, Alberta, Canada VKhatchatrian@slb.com and Mike Galbraith, WesternGeco, Calgary, Alberta, Canada
More informationApplication of Coherent Noise Attenuation to 4-C Ocean Bottom Cable Seismic Data from the Niger Delta.
Australian Journal of Basic and Applied Sciences, 4(10): 4985-4994, 2010 ISSN 1991-8178 Application of Coherent Noise Attenuation to 4-C Ocean Bottom Cable Seismic Data from the Niger Delta. 1 D.O. Ogagarue,
More informationAntenna Measurements using Modulated Signals
Antenna Measurements using Modulated Signals Roger Dygert MI Technologies, 1125 Satellite Boulevard, Suite 100 Suwanee, GA 30024-4629 Abstract Antenna test engineers are faced with testing increasingly
More informationSeismic acquisition projects 2010
Acquisition 2010 Seismic acquisition projects 2010 Malcolm B. Bertram, Kevin L. Bertram, Kevin W. Hall, Eric V. Gallant ABSTRACT Acquisition projects since the CREWES meeting in November 2009 include:
More informationERTH3021 Note: Terminology of Seismic Records
ERTH3021 Note: Terminology of Seismic Records This note is intended to assist in understanding of terminology used in practical exercises on 2D and 3D seismic acquisition geometries. A fundamental distinction
More informationHigh Performance Seismic Sensor Requirements for Military and Security Applications
High Performance Seismic Sensor Requirements for Military and Security Applications A. Pakhomov, D. Pisano, A. Sicignano, and T. Goldburt * General Sensing Systems, LLC, 440 Saw Mill River Road, Ardsley,
More informationTexas Components - Data Sheet. The TX53G1 is an extremely rugged, low distortion, wide dynamic range sensor. suspending Fluid.
Texas Components - Data Sheet AN004 REV A 08/30/99 DESCRIPTION and CHARACTERISTICS of the TX53G1 HIGH PERFORMANCE GEOPHONE The TX53G1 is an extremely rugged, low distortion, wide dynamic range sensor.
More informationIntroduction. Field Test Description
GEO21 Seismic Repeatability - Is There a Limit? E. Schissele (CGGVeritas), E. Forgues (CGGVeritas), J. J.Postel* (CGGVeritas), J. Meunier (CGGVeritas), O. de Pellegars (Total) & C. Hubans (Total) SUMMARY
More informationA Dissertation Presented for the Doctor of Philosophy Degree. The University of Memphis
A NEW PROCEDURE FOR ESTIMATION OF SHEAR WAVE VELOCITY PROFILES USING MULTI STATION SPECTRAL ANALYSIS OF SURFACE WAVES, REGRESSION LINE SLOPE, AND GENETIC ALGORITHM METHODS A Dissertation Presented for
More informationAn analysis of passive seismic recording performance
Passive seismic recording performance An analysis of passive seismic recording performance Henry C. Bland ABSTRACT Passive seismic recording has many uses in oil and gas industry. It is used for fracture
More informationRepeatability Measure for Broadband 4D Seismic
Repeatability Measure for Broadband 4D Seismic J. Burren (Petroleum Geo-Services) & D. Lecerf* (Petroleum Geo-Services) SUMMARY Future time-lapse broadband surveys should provide better reservoir monitoring
More informationTechnology of Adaptive Vibroseis for Wide Spectrum Prospecting
Technology of Adaptive Vibroseis for Wide Spectrum Prospecting Xianzheng Zhao, Xishuang Wang, A.P. Zhukov, Ruifeng Zhang, Chuanzhang Tang Abstract: Seismic data from conventional vibroseis prospecting
More informationCDP noise attenuation using local linear models
CDP noise attenuation CDP noise attenuation using local linear models Todor I. Todorov and Gary F. Margrave ABSTRACT Seismic noise attenuation plays an important part in a seismic processing flow. Spatial
More informationControl Servo Design for Inverted Pendulum
JGW-T1402132-v2 Jan. 14, 2014 Control Servo Design for Inverted Pendulum Takanori Sekiguchi 1. Introduction In order to acquire and keep the lock of the interferometer, RMS displacement or velocity of
More informationISSCC 2006 / SESSION 16 / MEMS AND SENSORS / 16.1
16.1 A 4.5mW Closed-Loop Σ Micro-Gravity CMOS-SOI Accelerometer Babak Vakili Amini, Reza Abdolvand, Farrokh Ayazi Georgia Institute of Technology, Atlanta, GA Recently, there has been an increasing demand
More informationInvestigating the low frequency content of seismic data with impedance Inversion
Investigating the low frequency content of seismic data with impedance Inversion Heather J.E. Lloyd*, CREWES / University of Calgary, Calgary, Alberta hjelloyd@ucalgary.ca and Gary F. Margrave, CREWES
More informationPresented on. Mehul Supawala Marine Energy Sources Product Champion, WesternGeco
Presented on Marine seismic acquisition and its potential impact on marine life has been a widely discussed topic and of interest to many. As scientific knowledge improves and operational criteria evolve,
More informationDesign of an Optimal High Pass Filter in Frequency Wave Number (F-K) Space for Suppressing Dispersive Ground Roll Noise from Onshore Seismic Data
Universal Journal of Physics and Application 11(5): 144-149, 2017 DOI: 10.13189/ujpa.2017.110502 http://www.hrpub.org Design of an Optimal High Pass Filter in Frequency Wave Number (F-K) Space for Suppressing
More informationData and Computer Communications. Chapter 3 Data Transmission
Data and Computer Communications Chapter 3 Data Transmission Data Transmission quality of the signal being transmitted The successful transmission of data depends on two factors: characteristics of the
More informationǤ CONFERENCE ABSTRACTS 161
CONFERENCE ABSTRACTS 161 162 EXPANDED ABSTRACT SEG 2010 163 Qualitative seismic sensor array estimation and seafloor coupling by using incoherent ambient signals for reservoir-monitoring-systems Marcus
More informationFrequency-Modulated Continuous-Wave Radar (FM-CW Radar)
Frequency-Modulated Continuous-Wave Radar (FM-CW Radar) FM-CW radar (Frequency-Modulated Continuous Wave radar = FMCW radar) is a special type of radar sensor which radiates continuous transmission power
More informationANALYSIS OF 3RD OCTAVE BAND GROUND MOTIONS TRANSMISSION IN SYNCHROTRON RADIATION FACILITY SOLARIS Daniel Ziemianski, Marek Kozien
ANALYSIS OF 3RD OCTAVE BAND GROUND MOTIONS TRANSMISSION IN SYNCHROTRON RADIATION FACILITY SOLARIS Daniel Ziemianski, Marek Kozien Cracow University of Technology, Institute of Applied Mechanics, al. Jana
More informationOPTICAL BACKSCATTER REFLECTOMETER TM (Model OBR 5T-50)
OPTICAL BACKSCATTER REFLECTOMETER TM (Model OBR 5T-50) The Luna OBR 5T-50 delivers fast, accurate return loss, insertion loss, and length measurements with 20 micron spatial resolution. PERFORMANCE HIGHLIGHTS
More informationResponse spectrum Time history Power Spectral Density, PSD
A description is given of one way to implement an earthquake test where the test severities are specified by time histories. The test is done by using a biaxial computer aided servohydraulic test rig.
More informationModule 2 WAVE PROPAGATION (Lectures 7 to 9)
Module 2 WAVE PROPAGATION (Lectures 7 to 9) Lecture 9 Topics 2.4 WAVES IN A LAYERED BODY 2.4.1 One-dimensional case: material boundary in an infinite rod 2.4.2 Three dimensional case: inclined waves 2.5
More informationKeywords: Transition zone, 3D-2C, air gun and explosive, dual sensors, geophones & marshy geophones, quality of seismic data, backwater, OBC.
3D-2C Transition Zone Seismic Survey in Palk Bay, Cauvery Basin-A Case Study Manoj Kumar Bhartee, Rupjit Acharjya, Anil Sharma & Chaman Singh Email id: bhartee_mk@ongc.co.in SUMMARY To explore for hydrocarbons
More informationField comparison of 3-C geophones and microphones to highprecision
Geophones, microphones and blasting sensors Field comparison of 3-C geophones and microphones to highprecision blasting sensors Alejandro D. Alcudia, Robert R. Stewart, Kevin W. Hall and Eric V. Gallant
More informationChapter 17 Waves in Two and Three Dimensions
Chapter 17 Waves in Two and Three Dimensions Slide 17-1 Chapter 17: Waves in Two and Three Dimensions Concepts Slide 17-2 Section 17.1: Wavefronts The figure shows cutaway views of a periodic surface wave
More information