Udstyr og systemer til maritim navigation og radiokommunikation Skibsradar Ydeevnekrav, prøvningsmetoder og krævede prøvningsresultater

Transcription

1 Dansk standard DS/EN udgave Udstyr og systemer til maritim navigation og radiokommunikation Skibsradar Ydeevnekrav, prøvningsmetoder og krævede prøvningsresultater Maritime navigation and radiocommunication equipment and systems Shipborne radar Performance requirements, methods of testing and required test results

2 DS/EN København DS projekt: M ICS: ; Første del af denne publikations betegnelse er: DS/EN, hvilket betyder, at det er en europæisk standard, der har status som dansk standard. Denne publikations overensstemmelse er: IDT med: IEC ED 2.0:2013. IDT med: EN 62388:2013. DS-publikationen er på engelsk. Denne publikation erstatter: DS/EN 62388:2008. DS-publikationstyper Dansk Standard udgiver forskellige publikationstyper. Typen på denne publikation fremgår af forsiden. Der kan være tale om: Dansk standard standard, der er udarbejdet på nationalt niveau, eller som er baseret på et andet lands nationale standard, eller standard, der er udarbejdet på internationalt og/eller europæisk niveau, og som har fået status som dansk standard DS-information publikation, der er udarbejdet på nationalt niveau, og som ikke har opnået status som standard, eller publikation, der er udarbejdet på internationalt og/eller europæisk niveau, og som ikke har fået status som standard, fx en teknisk rapport, eller europæisk præstandard DS-håndbog samling af standarder, eventuelt suppleret med informativt materiale DS-hæfte publikation med informativt materiale Til disse publikationstyper kan endvidere udgives tillæg og rettelsesblade DS-publikationsform Publikationstyperne udgives i forskellig form som henholdsvis fuldtekstpublikation (publikationen er trykt i sin helhed) godkendelsesblad (publikationen leveres i kopi med et trykt DS-omslag) elektronisk (publikationen leveres på et elektronisk medie) DS-betegnelse Alle DS-publikationers betegnelse begynder med DS efterfulgt af et eller flere præfikser og et nr., fx DS 383, DS/EN 5414 osv. Hvis der efter nr. er angivet et A eller Cor, betyder det, enten at det er et tillæg eller et rettelsesblad til hovedstandarden, eller at det er indført i hovedstandarden. DS-betegnelse angives på forsiden. Overensstemmelse med anden publikation: Overensstemmelse kan enten være IDT, EQV, NEQ eller MOD IDT: Når publikationen er identisk med en given publikation. EQV: Når publikationen teknisk er i overensstemmelse med en given publikation, men præsentationen er ændret. NEQ: Når publikationen teknisk eller præsentationsmæssigt ikke er i overensstemmelse med en given standard, men udarbejdet på baggrund af denne. MOD: Når publikationen er modificeret i forhold til en given publikation.

3 EUROPEAN STANDARD EN NORME EUROPÉENNE EUROPÄISCHE NORM October 2013 ICS ; Supersedes EN 62388:2008 English version Maritime navigation and radiocommunication equipment and systems - Shipborne radar - Performance requirements, methods of testing and required test results (IEC 62388:2013) Matériels et systèmes de navigation et de radiocommunication maritimes - Radars de bord - Exigences de performance, méthodes d essai et résultats exigés (CEI 62388:2013) Navigations- und Funkkommunikationsgeräte und -systeme für die Seeschifffahrt - Radar für Schiffe - Leistungsanforderungen, Prüfverfahren und geforderte Prüfergebnisse (IEC 62388:2013) This European Standard was approved by CENELEC on CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B Brussels 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 62388:2013 E

4 EN 62388: Foreword The text of document 80/696/FDIS, future edition 2 of IEC 62388, prepared by IEC TC 80 Maritime navigation and radiocommunication equipment and systems was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62388:2013. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement latest date by which the national standards conflicting with the document have to be withdrawn (dop) (dow) This document supersedes EN 62388:2008. EN 62388:2013 includes the following significant technical changes with respect to EN 62388:2008: In 6.2 (Transmission and interference) reference is now made to a revised Annex B (Unwanted emissions) where the mask has been tightened from 20 db/decade to 30 db/decade in line with ITU requirements and a new informative Annex J has been added concerning interference from emissions in adjacent frequency bands; Clause 7 (Display presentation) has been simplified (and the previous Annexes J and K deleted) with reference made instead to EN with associated changes throughout the standard; In (PI lines and positioning) the requirements for parallel index lines have been revised; In (Display orientation) a new mode of display orientation head-up stabilised has been added; In 11.5 (Automatic Identification System) new requirements and tests have been added for types of AIS targets, AIS repeater stations and filtering of AIS targets; In Clause 12 (Chart radar) a new subclause 12.3 has been added for ECDIS backup requirements; In Clause 13 (Ergonomic criteria) a new subclause 13.5 has been added giving requirements for default control settings; 14.3 (Output interfacing) has been revised together with the associated Annex H to update the requirements particularly with regard to interfaces to the VDR; Clause 16 (Alerts and failures) has been revised to update the requirements to align with bridge alert management and new requirements added for an alert management interface with associated changes throughout the standard; In Clause 18 (Equipment familiarisation and documentation) a new subclause 18.3 has been added for maintenance information and equipment update. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.

5 - 3 - EN 62388:2013 Endorsement notice The text of the International Standard IEC 62388:2013 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC NOTE Harmonised as EN ISO 9000 NOTE Harmonised as EN ISO ISO NOTE Harmonised as EN ISO ISO NOTE Harmonised as EN ISO

6 EN 62388: Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC Maritime navigation and radiocommunication equipment and systems - General requirements - Methods of testing and required test results IEC series Maritime navigation and radiocommunication equipment and systems - Digital interfaces IEC Maritime navigation and radiocommunication equipment and systems - Electronic chart display and information system (ECDIS) - Operational and performance requirements, methods of testing and required test results IEC Maritime navigation and radiocommunication equipment and systems - Integrated navigation systems - Part 2: Modular structure for INS - Operational and performance requirements, methods of testing and required test results IEC Maritime navigation and radiocommunication equipment and systems - Shipborne voyage data recorder (VDR) - Part 1: Performance requirements, methods of testing and required test results IEC Maritime navigation and radiocommunication equipment and systems - Presentation of navigationrelated information on shipborne navigational displays - General requirements, methods of testing and required test results ITU-R Recommendation M.628 ITU-R Recommendation M Technical characteristics for search and rescue radar transponders - Technical parameters of radar beacons (racons) EN EN EN series EN EN EN

7 - 5 - EN 62388:2013 Publication Year Title EN/HD Year ITU-R Recommendation M Technical parameters of radar target enhancers IHO S-52 - Specifications for chart content and display aspects of ECDIS IHO S-52, Appendix 2, Annex A IMO Resolution A.424(IX) IMO Resolution A.694(17) IMO Resolution A.821(19) IMO Resolution MSC.96(72) IMO Resolution MSC.116(73) IMO Resolution MSC.191(79) IMO Resolution MSC.192(79) IMO Resolution MSC.232(82) IMO Resolution MSC.302(87) IMO MSC.1/Circ IHO ECDIS Presentation Library - Performance standards for gyrocompasses - General requirements for shipborne radio equipment forming part of the global maritime distress and safety system (GMDSS) and for electronic navigational aids - Performance standards for gyrocompasses for high-speed craft - Amendments to performance standards for devices to indicate speed and distance (resolution A.824(19)) - Performance standards for marine transmitting heading devices (THDs) - Performance standards for the presentation of navigation-related information on shipborne navigational displays - Adoption of the revised performance standards for radar equipment - Revised performance standards for electronic chart display and information systems (ECDIS) - Adoption of performance standards for Bridge Alert Management - Guidance on procedures for updating shipborne navigation and communication equipment VESA Industry Standards and Guidelines for Computer Display Monitor Timing (DMT) Standard DDWG DVI 1999 Digital Visual Interface (DVI) Revision 1.0, Digital Display Working Group (DDWG)

8

9 COPYRIGHT Danish Standards Foundation. Not for commercial use or reproduction. DS/EN 62388:2013 IEC Edition INTERNATIONAL STANDARD colour inside IEC 62388:2013(E) Maritime navigation and radiocommunication equipment and systems Shipborne radar Performance requirements, methods of testing and required test results

10 IEC:2013(E) CONTENTS FOREWORD Scope Normative references Terms and definitions General Overview Purpose Application of these standards Equipment categories Establishing equipment type and status Conditions of measurement and related definitions Quality requirements Tests Test sites and simulation Environmental and RF testing Over-sea radar performance tests Test targets and target simulation for performance tests Test terminology and format General Test requirement terminology Testing method terminology Radar performance General Transmission and interference Transmission frequency Interference Performance optimisation and monitoring General Optimum performance Gain and anti-clutter functions General Gain function Manual and automatic sea anti-clutter Rain anti-clutter Signal processing General Target enhancement Radar signal correlation Signal processing and radar image latency Second-time-around echoes Transmission format Picture update Additional processing Signal processing description Operation with SARTs, target enhancers (RTEs) and beacons General... 38

11 62388 IEC:2013(E) Radar beacons, SARTs and enhancers Minimum range and range compensation General Range compensation Minimum range Range and bearing discrimination General Measurement conditions Range discrimination Bearing discrimination Fundamental radar accuracy Target detection performance assessment General Range of first detection in minimal clutter Assessment of target detection with clutter Radar performance documentation Radar antenna (including pitch and roll) General Vertical radiation pattern/pitch and roll Antenna horizontal pattern Antenna side lobes Radar availability Standby and transmit Requirements Methods of test and required results Display presentation General Requirements Methods of test and required results Linearity and index delay Requirements Methods of test and required results Use and discrimination of colour Requirements Methods of test and required results CCRP and own ship Consistent common reference point (CCRP) CCRP CCRP position Measurements Antenna offset Own ship General Own ship s outline and minimised symbol Heading line Stern line Navigation tools General Units of measurement Requirements... 56

12 IEC:2013(E) Methods of test and required results Presentation Requirements Methods of test and required results Display range scales Mandatory range scales Variable range marker (VRM) General VRM measurements Electronic bearing line (EBL) General EBL measurements EBL origin position Cursor General Cursor measurement Selection by cursor Offset measurement of range and bearing General Electronic range and bearing line (ERBL) Parallel index lines (PI) General PI lines and positioning Bearing scale General Bearing scale presentation Range rings General Range ring presentation and measurement Radar maps General Map functions and display simple user-defined maps Map memory and transfer Map presentation properties Navigation routes General Route display and monitoring Orientation, motion and stabilisation General Azimuth orientation Accuracy of alignment Heading readout and reference Azimuth stabilisation update Motion and orientation modes General True and relative motion Off-centring General Manual and automatic off-centring... 70

13 62388 IEC:2013(E) Automatic reset Display orientation Ground and sea stabilisation Mode and source Ground stabilisation Sea stabilisation Aids for collision avoidance General Target trails and past positions General Time and plot requirements Trails/past position availability Target tracking (TT) General Presentation of targets Tracking calculations Target tracking availability Classification and tracked target capacity Manual acquisition Automatic acquisition Motion trend Visibility of 50 % Tracking algorithm Target swap Cease tracking Target tracking scenarios Target motion and tracking accuracy Tracker range and bearing accuracy Reference target Tracking limitations Tracking warnings Documentation Requirements Methods of test and required results Automatic identification system General AIS targets and data report capacity AIS target filtering Activation and deactivation of AIS targets AIS functionality and presentation Radar and AIS target data Requirements Methods of test and required results Bow crossing range and time (BCR/BCT) Operational target alerts CPA and TCPA New target warning Lost tracked radar target Lost AIS target criteria... 98

14 IEC:2013(E) 11.8 Target association General Association and priority Trial manoeuvre General Trial functions Chart radar (optional classification) General requirements General Chart operation and source Chart elements and availability Chart reference Primary chart information set Chart stabilisation and chart redraw Chart position and latency Matching and adjustment Chart symbols, colours, and size Chart display size Chart alerts and indications Chart malfunction Chart radar malfunction Additional requirements for standalone radar with chart facilities General Provision and updating of chart information Content and structure of chart data Additional requirements for ECDIS back-up (optional) General Requirements Test Methods and required results Ergonomic criteria (control functions and display) General Operational controls Requirements Methods of test and required results Primary controls Requirements Methods of test and required results Control properties Requirements Methods of test and required results Default control setting and saved user control settings Requirements Test methods and required results Interfacing General Input interfacing Input data Input quality, integrity and latency Output interfacing

15 62388 IEC:2013(E) Output format Output target data VDR interface Design, servicing and installation General Fault diagnosis and servicing Requirements Methods of test and required results Display design Requirements Methods of test and required results Transceiver design General Sector blanking Antenna design Requirements Methods of test and required results Inter-switched and multiple radars General System safeguards Combining radar Multiple radar system status Multiple operational displays Additional information and conformity Requirements Methods of test and required results Safety antenna and radiation General Antenna radiation and rotation Microwave radiation levels Alerts and failures General Priority of alerts Alerts and indications Alarm contact outputs Alert management interface Unacknowledged warnings Unacknowledged alarms Remote acknowledgement and silencing of alerts Picture freeze Sensor failure alert Backup and fallback arrangements Requirements Failure of heading information (azimuth stabilisation) Failure of speed through the water information Failure of course and speed over ground information Failure of position input information Failure of radar video input information Failure of AIS input information

16 IEC:2013(E) Failure of an integrated or networked system Environmental testing General Testing to IEC Requirements Methods of test and required results Additional environmental tests General Antenna shock test Equipment familiarisation and documentation Familiarisation simulator General Requirements Methods of test and required results Instructions and documentation General Documentation Operating instructions Radar system installation Requirements Methods of test and required results Maintenance information for equipment update Requirements Methods of test and required results Annex A (informative) Guidelines for radar functionality on navigation displays Annex B (normative) Unwanted emissions of radar systems Annex C (informative) Radar target size (RCS) and detection range calculations Annex D (informative) Factors that influence target detection Annex E (normative) Sensor errors Annex F (informative) Target scenario simulator/reported target simulator Annex G (informative) Tracked and reported target states Annex H (normative) IEC sentence formats Annex I (normative) Radar control function/indication grouping Annex J (informative) Interference to shipborne radar from emissions in adjacent frequency bands Bibliography Figure 1 Reduction of range to first detection due to rain at S-band Figure 2 Reduction of range to first detection due to rain at X-band Figure 3 TT scenario Figure 4 TT scenario Figure 5 TT scenario Figure 6 TT scenario Figure 7 TT scenario Figure B.1 B 40 falls within the allocated band Figure B.2 B 40 falls outside the allocated band

17 62388 IEC:2013(E) 9 Figure C.1 Enhancement by reflection (db) over free-space (9,41 GHz) Figure C.2 Enhancement by reflection (db) over free-space (3,05 GHz) Figure D.1 Effect of sea spikes on target detection Figure D.2 Multi-path plots for S-band Figure D.3 Multi-path plot for X-band Figure G.1 Tracked target states Figure G.2 AIS target state Table 1 Performance requirements for categories of ship/craft for SOLAS V Table 2 Range of first detection in clutter-free conditions Table 3 X-band pass/fail assessment criteria Table 4 S-band pass/fail assessment criteria Table 5 Pass/fail assessment Table 6 Douglas sea state parameters Table 7 Main horizontal beam pattern Table 8 Effective side-lobes Table 9 Features and colours to be used for radar maps Table 10 Tracked target capacity (subset of Table 1) Table 11 Typical tracked target accuracy (95 % probability figures) Table 12 TT scenario 1, with sensor errors applied Table 13 TT scenario 1, times of measurement task Table 14 TT scenario 1, accuracies after 1 min and 3 min (all ± values) Table 15 TT scenario 2, own ship turning through ± Table 16 TT scenario 3, initial target data Table 17 TT scenario 4, initial target data for fast targets (standard speed ships) Table 18 TT scenario 4, initial target data for fast targets (HSC) Table 19 TT scenario 5: initial target data for standard craft Table 20 TT scenario 5: initial target data for collision scenario for HSC Table 21 Measurement points and results at 3 min and 6 min for HSC Table 22 Measurement points and results at 11 min and 14 min for HSC Table 23 Measurement points and results at 3 min and 6 min for standard craft Table 24 Measurement points and results at 11 min and 14 min for standard craft Table 25 Measurement of tracked target accuracy Table 26 AIS display capacity (subset of Table 1) Table 27 AIS reporting rates Table 28 Association scenario 1, initial TT and AIS target position and data Table 29 Association scenario 1, AIS target data for diverging and converging tracks Table 30 Association scenario 2, initial TT and AIS target position and data Table 31 Association scenario 2, AIS target data for changing speed Table 32 Association scenario 3, TT and AIS target start position and data Table 33 Association scenario 4, initial TT and AIS target position and data Table 34 Association scenario 4, TT and AIS target with the same course and speed Table 35 Control settings configured in response to Default selection

18 IEC:2013(E) Table 36 Antenna shock test severity (half sine pulse) Table B.1 Measurement frequency ranges Table D.1 Spread of RCS values for typical ships Table D.2 S-band performance predictions for ranges of 0,2, 0,4, 0,7 NM Table D.3 X-band performance predictions for ranges of 0,2, 0,7 NM Table D.4 Parameters for attenuation in uniform rain conditions Table D.5 Typical values for attenuation and backscatter in uniform rain conditions Table D.6 Additional radar system parameters (X/S-band) Table D.7 Target size, height and RCS values Table D.8 S-band radar parameters (LP) Table D.9 X-band radar parameters (LP) Table H.1 Mandatory IEC sentences Table H.2 Optional IEC messges Table H.3 Description of terms Table H.4 Header format (1 of 2) Table H.5 Package data format Table I.1 Top-level grouping of data and control functions for radar applications Table I.2 Icons for common function controls (1 of 2)

19 62388 IEC:2013(E) 11 INTERNATIONAL ELECTROTECHNICAL COMMISSION MARITIME NAVIGATION AND RADIOCOMMUNICATION EQUIPMENT AND SYSTEMS Shipborne radar Performance requirements, methods of testing and required test results FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as IEC Publication(s) ). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and nongovernmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC has been prepared by IEC technical committee 80: Maritime navigation and radiocommunication equipment and systems. This second edition cancels and replaces the first edition published in This edition constitutes a technical revision.

20 IEC:2013(E) The main changes with respect to the previous edition are: in 6.2 (Transmission and interference) reference is now made to a revised Annex B (Unwanted emmisions) where the mask has been tightened from 20 db/decade to 30 db/decade in line with ITU requirements and a new informative Annex J has been added concerning interference from emissions in adjacent frequency bands; Clause 7 (Display presentation) has been simplified (and the previous Annexes J and K deleted) with reference made instead to IEC with associated changes throughout the standard; in (PI lines and positioning) the requirements for parallel index lines have been revised; in (Display orientation) a new mode of display orientation head-up stabilised has been added; in 11.5 (Automatic identification system) new requirements and tests have been added for types of AIS targets, AIS repeater stations and filtering of AIS targets; in Clause 12 (Chart radar) a new subclause 12.3 has been added for ECDIS backup requirements; in Clause 13 (Ergonomic criteria) a new subclause 13.5 has been added giving requirements for default control settings; 14.3 (Output interfacing) has been revised together with the associated Annex H to update the requirements particularly with regard to interfaces to the VDR; Clause 16 (Alerts and failures) has been revised to update the requirements to align with bridge alert management and new requirements added for an alert management interface with associated changes throughout the standard; in Clause 18 (Equipment familiarisation and documentation) a new subclause 18.3 has been added for maintenance information and equipment update. The text of this standard is based on the following documents: FDIS 80/696/FDIS Report on voting 80/705/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. All the text in this standard with wording identical to that in IMO resolutions is printed in italics. Reference to MSC.192(79) is by the relevant requirement clause as indicated in brackets, for example (MSC.192/4.2.3). Some clauses from Resolution MSC.192(79) may be split and the requirements in this case are addressed separately. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

21 62388 IEC:2013(E) 13 The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under " in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IMPORTANT The 'colour inside' logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer.

22 IEC:2013(E) MARITIME NAVIGATION AND RADIOCOMMUNICATION EQUIPMENT AND SYSTEMS Shipborne radar Performance requirements, methods of testing and required test results 1 Scope This International Standard specifies the minimum operational and performance requirements, methods of testing and required test results conforming to performance standards not inferior to those adopted by the IMO in Resolution MSC.192(79). (MSC.192/2) The radar installation, in addition to meeting the general requirements as set out in resolution A.694(17) and the related standard IEC 60945, should comply with the performance standards of MSC.192(79). When a requirement of this standard is different from IEC 60945, the requirement in this standard takes precedence. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60945, Maritime navigation and radiocommunication equipment and systems General requirements Methods of testing and required test results IEC (all parts), Maritime navigation and radiocommunication equipment and systems Digital interfaces IEC 61174, Maritime navigation and radiocommunication equipment and systems Electronic chart display and information systems (ECDIS) Operational and performance requirements, methods of testing and required test results IEC :2012, Maritime navigation and radiocommunication equipment and systems Part 2 Modular Structure for INS - Operational and performance requirements, methods of testing and required test results IEC :2012, Maritime navigation and radiocommunication equipment and systems Shipborne voyage data recorder (VDR) Part 1: Voyage data recorder (VDR) - Performance requirements Methods of testing and required test results IEC 62288, Maritime navigation and radiocommunication equipment and systems Presentation of navigation-related information on shipborne navigational displays General requirements, methods of testing and required results ITU-R Recommendation M.628, Technical characteristics for search and rescue radar transponders ITU-R Recomendation M.824, Technical parameters of radar beacons (racons) ITU-R Recommendation M.1176, Technical parameters of radar target enhancers

23 62388 IEC:2013(E) 15 IHO S-52, Specifications for chart content and display aspects of ECDIS IHO S-52 Annex A, IHO ECDIS Presentation Library IMO Resolution A.424(XI), Performance standards for Gyro-compasses IMO Resolution A.694(17), General requirements for shipborne radio equipment forming part of the global maritime distress and safety system (GMDSS) and for electronic navigational aids IMO Resolution A.821(19), Performance standards for Gyro-compasses for High-Speed Craft IMO Resolution MSC.96(72), Amendments to IMO Resolution A.824(19), Performance standards for devices to indicate speed and distance IMO Resolution MSC.116(73), Performance standards for marine transmitting heading devices (THDs) IMO Resolution MSC.191(79), Performance standards for the presentation of navigationrelated information on shipborne navigational displays IMO Resolution MSC.192(79), Revised performance standards for radar equipment IMO Resolution MSC.232(82), Revised performance standards for electronic chart display and information systems (ECDIS) IMO Resolution MSC.302(87), Performance standards for bridge alert management IMO MSC.1/Circ.1389, Guidance on procedures for updating shipborne navigation and communication equipment VESA :2007, Industry standards and guidelines for computer display monitor timing (DMT) DDWG DVI:1999, Digital Visual Interface (DVI) Revision 1.0, Digital Display Working Group (DDWG) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 activated AIS target target representing the automatic or manual activation of a sleeping target for the display of additional graphically presented information Note 1 to entry: The target is displayed by an activated target symbol including a vector; the heading; and the ROT or direction of turn indication (if available) to indicate initiated course changes. [SOURCE: IMO Resolution MSC.192(79):2004, Appendix 2, modified added Note 1 to entry] 3.2 acquisition of a radar target process of acquiring a target and initiating its tracking [SOURCE: IMO Resolution MSC.192(79):2004, Appendix 2]