# Reducing Springback using post-stretching with stake beads By Tanmay Gupta, Ali Fallahiarezoodar, and Dr. Taylan Altan
|
|
- Caroline Shelton
- 5 years ago
- Views:
Transcription
1 Reducing Springback using post-stretching with stake beads By Tanmay Gupta, Ali Fallahiarezoodar, and Dr. Taylan Altan #688-4 Reducing springback, especially in forming of Advanced High Strength Steels (AHSS), is a major issue in sheet metal forming. An article, published in March/April 2018 issue of Stamping Journal was devoted to this subject. In this article, the use of servo hydraulic cushion and a variable Blank Holder Force (BHF) for applying post stretching and reducing of springback was discussed. Figure 1 illustrates a simple hat bending operation. In this case, the draw-in of the sheet material is controlled by blank holder force. In this forming operation, the sheet material undergoes both bending and unbending deformation. Thus, as result of elastic recovery of the strains, the material has a natural tendency to unbend itself in the side wall as well as in the bending corners of the hat shaped part. This causes the side wall to curl that affect the dimensional accuracy and final shape of the formed part. Springback is the result of non-uniform redistribution of stresses in sheet thickness. Thus, additional stretch/tension force on the part can reduce the unbending moment and consequently the springback. Post-stretching is a well-known method for reduction of springback at parts made by drawing operation. In this method, additional blank holder force is applied toward the end of deformation which cause additional stretch on the side wall and reduce the heterogeneous stress distributions. Figure 2 illustrates how the post stretching method can drastically modify the stress distributions in the wall from tensile-compression to tensile only. As a result, appropriate post stretching can reduce the springback in the part. Post stretching can be achieved using a variable BHF, as discussed earlier. However, many North American stampers do not use servo hydraulic cushion to generate variable BHF. Another method to reduce springback by post-stretching is to use the so-called lock bead or stake bead. An example of forming a hat shaped part with stake beads is seen in Figure 3. Figure 3a shows the tool setup at the start of deformation. In Figure 3b, the upper die moved down and formed the material up to the stroke where the beads start touching the blank. After this stage the blank is formed into the beads area and stretch force is applying on the side wall during the last few millimeters of the upper die stroke. Post-stretching with stake beads is used in the industry. Usually, the die design is such that a) the stake bead would not break or wear out easily, b) the stretching of the material in the bead itself does not cause any local fracture or cracks, and c) it provides adequate stretch at the side wall to reduce springback. As the blank is formed, when the beads start touching the sheet material, higher blank holder force is required to avoid any opening between the die and the blank holder. As a result, the total load on the die and press ram increases dramatically, as seen in the example shown in Figure 4. The load versus displacement curve shown in Figure 4 is the reaction force applied on the blank holder during the deformation. The reaction force is calculated from simulation with a constant gap between the die and the blank holder. However, in reality, when nitrogen cylinders or air cushion is used the blank holder force cannot be controlled or increased toward the end stroke as it can be done with a servo hydraulic cushion. Therefore, a high blank holder force should be applied at the beginning of the deformation stroke. This is one of the limitations of using stake bead for post stretching. 1
2 To minimize the increase of the force in forming with stake bead, for a given part geometry and blank material/thickness, the design of a die with stake bead requires the selection, or optimization, of a) stake bead radius and height (for a round bead). This selection must eliminate the possibility of fracture of the formed part in a) the part wall and b) the bead region. It is also desired to achieve this design objective with minimum force on the die, the max force F max, seen in Figure 4, should be as small as possible. A study of forming a hat shape part from 1.2 mm Al5182-O using a servo hydraulic cushion was performed at the Center for Precision Forming (CPF) in cooperation with Hyson Metalforming Solutions. Results showed that using a variable blank holder force can significantly reduce springback and side wall curl. Figure 5 shows the profile of the experimental result compared to numerical simulations. Simulations showed with both variable blank holder force (with appropriate selection of BHF) and servo hydraulic cushion and constant blank holder force and stake bead (with appropriate selection of the bed geometry), the side wall curl can be reduced. A study for developing a method for optimization the stake bead design is being conducted at the CPF at the Ohio State University. Tanmay Gupta (gupta.854@osu.edu) and Ali Fallahiarezoodar (fallahiarezoodar.1@ osu.edu) are graduate research associates and Dr. Taylan Altan (altan.1@osu.edu) is professor emeritus and director at the Center for Precision Forming (CPF) at The Ohio State University, 1971 Neil Ave., Room 339 Baker Systems Engineering Building, Columbus, OH 43210, , and Figure 1: Schematic of hat-shape bending using a variable BHF (no stake bead) 2
3 Figure 2: (a) Stress distribution before post-stretching; (b) Stress distribution after post-stretching 3
4 Figure 3: Stake Bead for Post-Stretching in hat bending; (a) die touches the blank, (b) hat shape drawing,(c) stake bead engaging before BDC and increase stretching in the wall 4
5 Figure 4: Example of the load versus stroke data in forming a hat shape part with stake bead Figure 5: Experiment and simulation result of hat shape bending with and without stake bead 5
Module 3 Selection of Manufacturing Processes
Module 3 Selection of Manufacturing Processes Lecture 4 Design for Sheet Metal Forming Processes Instructional objectives By the end of this lecture, the student will learn the principles of several sheet
More informationDesign and Manufacturing of U-Bending Tool to Overcome Spring Back Effect by Ironing Impact
Design and Manufacturing of U-Bending Tool to Overcome Spring Back Effect by Ironing Impact Manjunathan.R 1*, Mohanraj.R 1, Moshay.M 1, Natchimuthu.N 1, Suresh.S 2 1 Final year UG student, Department of
More informationBending. the bend radius is measured to the inner surface of the bent part
Bending the bend radius is measured to the inner surface of the bent part there is a plane which separates the tension and compression zones. This plane is called neutral axis. The position of neutral
More informationInfluence of Lubrication and Draw Bead in Hemispherical Cup Forming
INSTITUTE OF TECHNOLOGY, NIRMA UNIVERSITY, AHMEDABAD 382 481, 08-10 DECEMBER, 2011 1 Influence of Lubrication and Draw Bead in Hemispherical Cup Forming G. M. Bramhakshatriya *12, S. K. Sharma #1, B. C.
More informationDrawing of Hexagonal Shapes from Cylindrical Cups
Dr. Waleed Khalid Jawed Metallurgy & Production Engineering Department, University of Technology /Baghdad Email: Drwaleed555@yahoo.com Sabih Salman Dawood Metallurgy & Production Engineering Department,
More informationCorso di Studi di Fabbricazione
Corso di Studi di Fabbricazione 3a Richiami dei processi tecnologici di trasformazione FUNDAMENTAL OF METAL FORMING 1 METAL FORMING Large group of manufacturing processes in which plastic deformation is
More informationManufacturing Processes (1)
Manufacturing Processes (1) Chapter Twenty: Sheet Metalworking Dr. Eng. Yazan Al-Zain Department of Industrial Engineering 1 Introduction Sheet Metalworking includes cutting and forming operations performed
More informationTALAT Lecture Deep Drawing. 15 pages, 16 figures. Advanced Level
TALAT Lecture 3704 Deep Drawing 15 pages, 16 figures Advanced Level prepared by K. Siegert and S. Wagner, Institut für Umformtechnik, Universität Stuttgart Objectives: Definition and explanation of terms
More informationMANUFACTURING TECHNOLOGY
MANUFACTURING TECHNOLOGY UNIT II SHEET METAL FORMING PROCESSES Sheet Metal Introduction Sheet metal is a metal formed into thin and flat pieces. It is one of the fundamental forms used in metalworking,
More informationMetal Stamping Glossary
Metal Stamping Glossary Alloy - A substance that has metallic properties and is composed of two or more chemical elements of which at least one is an elemental metal. Annealing - A process involving the
More informationHail University College of Engineering Department of Mechanical Engineering. Sheet-Metal Forming Processes and Equipment. Ch 16
Hail University College of Engineering Department of Mechanical Engineering Sheet-Metal Forming Processes and Equipment Ch 16 Sheet-Metal Forming Products made of sheet metals are all around us. They include
More informationMetal Working Processes
Metal Working Processes Bachelor of Industrial Technology Management with Honours Semester I Session 2013/2014 CLASSIFICATION OF MANUFACTURING PROCESSES TOPIC OUTLINE What is Sheet Metal? Sheet Metalworking
More informationDesign and Analysis of Progressive Die for Chain Link Plate
Design and Analysis of Progressive Die for Chain Link Plate Md Inaithul Rehaman #1, P Satish Reddy #2, Matta Manoj #3, N.Guru Murthy #4 ME Department, Prasiddha College of Engg and Technology, Anathavaram
More informationSheet Metal Forming. Part 1
Sheet Metal Forming Part 1 Sheet Metal Forming For products with versatile shapes and lightweight Dates to 5000 B.C. Products include metal desks, file cabinets, appliances, car bodies, beverage cans Common
More informationDesign and Analysis of Draw Bead Profile in Sheet Metal Forming Of Reinf-Rr End Upr-Lh/Rh for Safe Thinning
International Journal of Engineering Science Invention (IJESI) ISSN (Online): 2319 6734, ISSN (Print): 2319 6726 Volume 7 Issue 7 Ver IV July 2018 PP 01-10 Design and Analysis of Draw Bead Profile in Sheet
More informationUnit IV Drawing of rods, wires and tubes
Introduction Unit IV Drawing of rods, wires and tubes Drawing is a process in which the material is pulled through a die by means of a tensile force. Usually the constant cross section is circular (bar,
More informationThe Fine-Art of Sheet Metal Bending
The Fine-Art of Sheet Metal Bending Introduction...... 1 Bend allowances........2 Reverse engineering the k-factor........ 4 Principle types of bending........ 5 Tips and tricks....... 7 Other common types
More informationMANUFACTURING PROCESSES
1 MANUFACTURING PROCESSES - AMEM 201 Lecture 9: Sheet Metal Cutting & Forming Processes DR. SOTIRIS L. OMIROU Sheet Metal Cutting & Forming Processes - Application field- Sheet metal processing is an important
More informationTHE INFLUENCE OF BLANKHOLDER GAP ON DEEP DRAWING PROCESS USING FINITE ELEMENT METHOD
International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 13, December 2018, pp. 1510 1518, Article ID: IJMET_09_13_152 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=13
More informationSheet-Forming Processes
Sheet-Forming Processes Chapter 17 17.1 Introduction Sheet metal processes involve plane stress loadings and lower forces than bulk forming Almost all sheet metal forming is considered to be secondary
More informationTool School - Rotary Draw Bending Tooling. An Engineer s Guide to Bending Tubes
Tool School - Rotary Draw Bending Tooling An Engineer s Guide to Bending Tubes Tube Form Solutions Tool School Rotary Draw Bending Tooling Tool School Agenda: Introduction To Rotary Draw Bending Engineering
More informationAdvance in Sheet Metal Forming - One-step Solution, Multi-Beads, Gravity Prebending, Auto Nets, and Local Compensation
12 th International LS-DYNA Users Conference Metal Forming(2) Advance in Sheet Metal Forming - One-step Solution, Multi-Beads, Gravity Prebending, Auto Nets, and Local Compensation Xinhai Zhu & Li Zhang
More informationDESIGN PARAMETER ANALYSIS OF SINGLE STAGE DRAWING OF CYLINDRICAL CUP USING ALTAIR HYPERWORKS
DESIGN PARAMETER ANALYSIS OF SINGLE STAGE DRAWING OF CYLINDRICAL CUP USING ALTAIR HYPERWORKS Pravinkumar Moon Phd. Scholar,Shri. Jagdishprasd Jhabarmal Tibrewala University Vidhyanagri, Jhunjhunu-Churu
More informationDesign and Analysis of Press Tool Assembly
Design and Analysis of Press Tool Assembly Raveendra M.Tech Student ABSTRACT Press working may be defined as a chip less manufacturing process by which various components are made from sheet metal. This
More informationTALAT Lecture Stretch Forming. 13 pages, 10 figures. Basic Level
TALAT Lecture 3703 Stretch Forming 13 pages, 10 figures Basic Level prepared by K. Siegert and S. Wagner, Institut für Umformtechnik, Universität Stuttgart Objectives: to define important terms of the
More informationTUTORIAL 4: Combined Axial and Bending Problem Sketch Path Sweep Initial Project Space Setup Static Structural ANSYS
TUTORIAL 4: Combined Axial and Bending Problem In this tutorial you will learn how to draw a bar that has bends along its length and therefore will have both axial and bending stresses acting on cross-sections
More informationImproving Edge Quality in Film Applications with Tangent Shear Slitting
Improving Edge Quality in Film Applications with Tangent Shear Slitting Presented by: Sean Craig General Manager, Maxcess-Tidland Date: October 17, 2017 What is Fracture Mechanics? The study of how things
More informationMANUFACTURING TECHNOLOGY
MANUFACTURING TECHNOLOGY UNIT II SHEET METAL FORMING PROCESSES Sheet metal Process in detail Cutting (Shearing) Operations Manufacturing Technology In this operation, the work piece is stressed beyond
More informationDESIGN OF DRAW DIE FOR CYLINDRICAL CUP FORMATION
DESIGN OF DRAW DIE FOR CYLINDRICAL CUP FORMATION Mr.Bhushan Sanjay Paysheti, Dr. Shekhar Yadgiri Gajjal Abstract For production of sheet metal parts we need various dies (press tools) which will convert
More informationStretch Forming Analysis for Skin of Aircraft, Model. B Abstract
Stretch Forming Analysis for Skin of Aircraft, Model. B717-200 Paper Reference Number: 2001-89 Myung-Hyun. Jung Aerospace Div. Korean Air co, Korea. Tel: 82-01-051-970-5639 E-mail: jumyhy@dreamx.net Abstract
More informationPrinciples of Rotary Bending Technology & Use of Rotary Bending Technology for Processing of Advanced, High-Strength Steels (AHSS)
Principles of Rotary Bending Technology & Use of Rotary Bending Technology for Processing of Advanced, High-Strength Steels (AHSS) L. Ray Osborne rosborne@anchordanly.com Mechanical Engineer / Business
More informationLS-DYNA USED TO ANALYZE THE MANUFACTURING OF THIN WALLED CANS AUTHOR: CORRESPONDENCE: ABSTRACT
LS-DYNA USED TO ANALYZE THE MANUFACTURING OF THIN WALLED CANS AUTHOR: Joachim Danckert Department of Production Aalborg University CORRESPONDENCE: Joachim Danckert Department of Production Fibigerstraede
More informationComputer Simulated and Experimental Verification of Tooling for Progressive Deep Drawing.
8 th International LS-DYNA Users Conference Metal Forming (1) Computer Simulated and Experimental Verification of Tooling for Progressive Deep Drawing. Peter Kostka, Peter Cekan Slovak University of Technology
More informationCost- and Quality-prioritized Methodology Towards Robust Stamping Process Solutions
Cost- and Quality-prioritized Methodology Towards Robust Stamping Process Solutions Yu-Wei Wang, AK Steel Evangelos Liasi, Ford Motor Company Kidambi Kannan, AutoForm Engineering USA Troubleshooting Production
More informationSection 10s PRESS BRAKE TOOLING. Product of USA SOURCE CATALOG FOR AMERICAN STYLE
www.ceooling.com Section 0s PRESS BRAKE OOLING SOURCE CAALOG FOR AMERICAN SYLE Product of USA 90 Forming Punches and Dies 90 Forming Punches and Dies hese punches and dies are the most widely used to form
More informationHEMMING THIN GAUGE ADVANCED HIGH STRENGTH STEEL
HEMMING THIN GAUGE ADVANCED HIGH STRENGTH STEEL AUTO/STEEL PARTNERSHIP PROJECT #AS-8004 Mark Hineline - AutoForm Engineering May 11, 2016 Auto/Steel Partnership Participants Project Outline Introduction
More information1/2/2016. Lecture Slides. Screws, Fasteners, and the Design of Nonpermanent Joints. Reasons for Non-permanent Fasteners
Lecture Slides Screws, Fasteners, and the Design of Nonpermanent Joints Reasons for Non-permanent Fasteners Field assembly Disassembly Maintenance Adjustment 1 Introduction There are two distinct uses
More informationBending of Sheet Metal (st37) Using 90 Degree to Estimate Blank Dimensions
23 THE INTERNATIONAL JOURNAL OF ENGINEERING AND INFORMATION TECHNOLOGY (IJEIT), VOL. 2, NO. 1, 2015 Bending of Sheet Metal (st37) Using 90 Degree to Estimate Blank Dimensions M. EM. Abid Tripoli University/Marine
More informationSIMULATION AND EXPERIMENTAL WORK OF SINGLE LAP BOLTED JOINT TESTED IN BENDING
SIMULATION AND EXPERIMENTAL WORK OF SINGLE LAP BOLTED JOINT TESTED IN BENDING Aidy Ali *, Ting Wei Yao, Nuraini Abdul Aziz, Muhammad Yunin Hassan and Barkawi Sahari Received: Jun 13, 2007; Revised: Nov
More informationDesign Guide: Sheet Metal Fabrication VERSION 2.1
Design Guide: Sheet Metal Fabrication VERSION 2.1 SHEET METAL GUIDE V2.1 Table of Contents Overview...3 Tolerances...4 General Tolerances...4 Wall Thickness...5 Bends...5 Curls...6 Countersinks...6 Hems...7
More informationSheet metal tutorial. To set the bend radius Right click on the first sheet metal icon in the command manager and specify a bend radius or 1mm.
Sheet metal tutorial In the following tutorial you will cover the basic features of the Solid Works sheet metal tool by modelling the component shown opposite. Activating Sheet metal mode Sheet metal components
More informationThe Formability of Perforated Metals, Part II: Stainless Steel and Aluminum
The Formability of Perforated Metals, Part II: Stainless Steel and Aluminum A follow-up study sponsored by The Industrial Perforators Association and conducted by Robert H. Wagoner, Department of Materials
More informationUniversal Sheet Metal Testing Machines. for Research, Development and In-process Testing
Universal Sheet Metal Testing Machines for Research, Development and In-process Testing Application - Example: Automotive Industry Models - Technical Data - Additional Control Functions and Test Methods
More informationMaterials. Density, Hooke's law, Young modulus. 174 minutes. 174 marks. Page 1 of 29
Materials Density, Hooke's law, Young modulus 174 minutes 174 marks Page 1 of 29 Q1. A uniform wooden beam of mass 35.0 kg and length 5.52 m is supported by two identical vertical steel cables A and B
More informationDesign of Punch and Die for Trimming Operation of Differential Bearing Cap
International Journal of Current Engineering and Technology E-ISSN 2277 4106, P-ISSN 2347 5161 2017 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Research Article Design
More informationPress Operations & Types of Dies
Press Operations & Types of Dies Press Working Use of mechanical and hydraulic presses for forging and extrusion has been mentioned earlier. Knuckle type mechanical presses are used widely for sheet metal
More information(1) Brass, an alloy of copper and zinc, consists of 70% by volume of copper and 30% by volume of zinc.
PhysicsAndMathsTutor.com 1 Q1. (a) Define the density of a material....... (1) Brass, an alloy of copper and zinc, consists of 70% by volume of copper and 30% by volume of zinc. density of copper = 8.9
More informationProviding Tools To Form Your Success
If it's important to you, it's important to us. Find out how our attention to details forms the basis for your success. Providing ools o able of Contents For more than 30 years, leading sheet metal fabricators
More informationCopyright 1997 Society of Manufacturing Engineers FUNDAMENTAL MANUFACTURING PROCESSES SHEET METAL SHEARING AND BENDING
FUNDAMENTAL MANUFACTURING PROCESSES SHEET METAL SHEARING AND BENDING SCENE 1. CG: FBI warning SCENE 2. CG: disclaimer Always read the operating manual and safety information provided by the manufacturer
More informationEVALUATION OF DRAW BEADS INFLUENCE ON INTRICATE SHAPE STAMPING DRAWING PROCESS
TECHNOLOGICAL ENGINEERING volume XI, number 1/2014 DOI: 10.2478/teen-2014-0001 EVALUATION OF DRAW BEADS INFLUENCE ON INTRICATE SHAPE STAMPING DRAWING PROCESS Article history: Received 10 september 2014
More informationINTRODUCTION TO PRESS BRAKES. A Vital Piece of Shop Equipment
INTRODUCTION TO PRESS BRAKES A Vital Piece of Shop Equipment Introduction to Press Brakes Press Brakes are utilized in the forming lengths of sheet metal components. A press brake is a vital necessity
More informationExperimental Investigation on Locally Increasing the Thickness of Sheet Metal by Beading and Compression Technique
Mindanao Journal of Science and Technology Vol. () 5- Experimental Investigation on Locally Increasing the Thickness of Sheet Metal by Beading and Compression Technique Consorcio S. Namoco, Jr. *, Takashi
More informationIn 1950, plastic film was relatively
TECHNICAL REPORT BY REINHOLD SCHABLE, APPLICATIONS TECHNOLOGY MANAGER, TIDLAND CORP. Slitting Technology for Film Substrates In 1950, plastic film was relatively uncommon, today it is everywhere. Back
More informationExperimental and numerical investigation of tube sinking of rectangular tubes from round section
International Journal of Engineering and Technology sciences (IJETS) ISSN 2289-4152 Academic Research Online Publisher Research Article Experimental and numerical investigation of tube sinking of rectangular
More informationInternational Journal of Engineering Trends and Technology (IJETT) Volume 38 Number 4- August 2016
Design and Development of Mounting Bracket Y. V. Thokale 1, P. G. Karajagi 2 1 PG student, Mechanical Department, Siddhant College of Engineering, Pune, India. 2 Asst. Professor and Department Academic
More informationXXL-Center. Cutting. Bending. Forming. R E I N H A R D T MASCHINENBAU D SINDELFINGEN D SINDELFINGEN RICHARD-WAGNER-STR.
Cutting. Bending. Forming. XXL-Center D-71045 SINDELFINGEN P O S T F A C H 3 6 9 T E L E F O N 0 7 0 3 1-8 6 3-0 D-71065 SINDELFINGEN RICHARD-WAGNER-STR. 4 10 T E L E F A X 0 70 31-863-185 R E I N H A
More informationCreasing and Folding are critical steps in the box forming process. Dipl. Ing. Lukas Pescoller
Creasing and Folding are critical steps in the box forming process Dipl. Ing. Lukas Pescoller Paperboard is A thick, single or multiply paper based material. composed of several layers of pulp fibers with
More informationFUNDAMENTAL MANUFACTURING PROCESSES. Sheet Metal Stamping Dies & Processes-SD
FUNDAMENTAL MANUFACTURING PROCESSES Sheet Metal Stamping Dies & Processes-SD SCENE 1. SD20A, CGS: Dies & Die Functions white text, centered on background FMP BKG, motion background SCENE 2. SD20A, SME4311,
More informationHINGE TOOL SET-UP, ADJUSTMENT AND TROUBLESHOOTING GUIDE
HINGE TOOL SET-UP, ADJUSTMENT AND TROUBLESHOOTING GUIDE HINGE TOOL FORMING SET-UP High Level Process (For detailed information, reference Detailed Instructions): 1. Inspect and assemble tool (if required).
More informationDEVELOPMENT OF A NOVEL TOOL FOR SHEET METAL SPINNING OPERATION
DEVELOPMENT OF A NOVEL TOOL FOR SHEET METAL SPINNING OPERATION Amit Patidar 1, B.A. Modi 2 Mechanical Engineering Department, Institute of Technology, Nirma University, Ahmedabad, India Abstract-- The
More informationForming Box-Shaped Ends in Circular Tubes
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING Vol. 16, No. 9, pp. 1975-1981 AUGUST 2015 / 1975 DOI: 10.1007/s12541-015-0257-0 ISSN 2234-7593 (Print) / ISSN 2005-4602 (Online) Forming
More informationStandard Test Methods for Bend Testing of Material for Ductility 1
Designation: E290 14 Standard Test Methods for Bend Testing of Material for Ductility 1 This standard is issued under the fixed designation E290; the number immediately following the designation indicates
More informationModule 10 : Improvement of rock mass responses. Content
IMPROVEMENT OF ROCK MASS RESPONSES Content 10.1 INTRODUCTION 10.2 ROCK REINFORCEMENT Rock bolts, dowels and anchors 10.3 ROCK BOLTING MECHANICS Suspension theory Beam building theory Keying theory 10.4
More informationEXPERIMENTAL INVESTIGATION OF FATIGUE BEHAVIOUR IN COMPOSITE BOLTED JOINTS
EXPERIMENTAL INVESTIGATION OF FATIGUE BEHAVIOUR IN COMPOSITE BOLTED JOINTS Roman Starikov 1 and Joakim Schön 2 1 Department of Aeronautics, Royal Institute of Technology SE-1 44 Stockholm, Sweden 2 Structures
More informationWire and tube Drawing
Wire and tube Drawing Drawing is an operation in which the cross-section of solid rod, wire or tubing is reduced or changed in shape by pulling it through a die. The principle of this procedure consist
More informationCyclic tests of engineered shear walls with different bottom plate and anchor bolt washer sizes (Phase II)
Cyclic tests of engineered shear walls with different bottom plate and anchor bolt washer sizes (Phase II) Prepared by Rakesh Gupta, Associate Professor Heather Redler, Graduate Research Assistant Milo
More informationExperimental investigation of crack in aluminum cantilever beam using vibration monitoring technique
International Journal of Computational Engineering Research Vol, 04 Issue, 4 Experimental investigation of crack in aluminum cantilever beam using vibration monitoring technique 1, Akhilesh Kumar, & 2,
More informationINTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY
INTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY A PATH FOR HORIZING YOUR INNOVATIVE WORK DESIGN, MANUFACTURING AND ANALYSIS OF SIMPLE PRESS TOOL MR. G. C. MEKALKE 1, MR.
More informationAnalytical model for predicting the surface profile of a work piece in round-to-2 R and square-to-2 R oval groove rolling
Journal of Mechanical Science and Technology 4 (11) () 89~95 www.springerlink.com/content/1738-494x DOI.7/s16--91-7 Analytical model for predicting the surface profile of a work piece in round-to- R and
More informationTrade of Sheet Metalwork. Module 7: Introduction to CNC Sheet Metal Manufacturing Unit 2: CNC Machines Phase 2
Trade of Sheet Metalwork Module 7: Introduction to CNC Sheet Metal Manufacturing Unit 2: CNC Machines Phase 2 Table of Contents List of Figures... 4 List of Tables... 5 Document Release History... 6 Module
More informationLaser Marking of Circular Grid Pattern for Plotting Strain Variation of Deep Drawing of Cylindrical Component
Laser Marking of Circular Grid Pattern for Plotting Strain Variation of Deep Drawing of Cylindrical Component Yalagandala Akshay Kumar M.Tech Student, Department of MECH (Machine Design), CVSR College
More informationA NEW MOTION COMPENSATION TECHNIQUE FOR INFRARED STRESS MEASUREMENT USING DIGITAL IMAGE CORRELATION
A NEW MOTION COMPENSATION TECHNIQUE FOR INFRARED STRESS MEASUREMENT USING DIGITAL IMAGE CORRELATION T. Sakagami, N. Yamaguchi, S. Kubo Department of Mechanical Engineering, Graduate School of Engineering,
More informationStudy on micro extra deep drawing process with ultrahigh fluid pressure and press motion controls
MATEC Web of Conferences 21, 09016 (2015) DOI: 10.1051/matecconf/20152109016 C Owned by the authors, published by EDP Sciences, 2015 Study on micro extra deep drawing process with ultrahigh fluid pressure
More informationDESIGN AND FABRICATION OF BENDING WITH TWISTING & CUTTING MACHINE
DESIGN AND FABRICATION OF BENDING WITH TWISTING & CUTTING MACHINE Swapnil Ghinmine 1, Shubham Thamke 2, Shubham Pawar 3, Shubham Khedkar 4, Shubham Wakde 5, Sumedh Patil 6, Suraj Sawarkar 7, Bhushan Fating
More informationTrade of Metal Fabrication. Module 3: Plate Fabrication Unit 1: Plate Forming Brake Press Phase 2
Trade of Metal Fabrication Module 3: Plate Fabrication Unit 1: Plate Forming Brake Press Phase 2 Table of Contents Table of Contents... 3 List of Figures... 5 List of Tables... 6 Document Release History...
More informationTHIN-WALLED HOLLOW BOLTS
THIN-WALLED HOLLOW BOLTS Experimental and numerical study Teixeira, C. D. S. Department of Mechanical Engineering, Instituto Superior Técnico, Av. Rovisco Pais, 1049-001, Lisbon, Portugal, 2010 Abstract
More informationTOOL DESIGN - MANUFACTURING DESIGN SPECIFICATIONS FOR TOOLING AND EQUIPMENT SECTION H - DIE DESIGN TABLE OF CONTENTS. H.1 General...
TABLE OF CONTENTS H.1 General...Page 2 H.2 General Die Layout...Page 2 H.3 General Die Features...Page 2 H.4 Specific Die Type Features...Page 5 H.5 Special Punches and Die Bushings...Page 6 H.6 Wire E.D.M...Page
More informationIMPROVEMENT OF CORRECTION ACCURACY IN FLANGE ROLLER LEVELER PROCESS FOR H-BEAM RYUMA TANIGUCHI *
IMPROVEMENT OF CORRECTION ACCURACY IN FLANGE ROLLER LEVELER PROCESS FOR H-BEAM BY RYUMA TANIGUCHI * SYNOPSIS Flange squareness of H-beam is corrected by Flange roller leveler in JFE Steel West Japan Works
More informationRB&W. GLOBAL LIGHTWEIGHT MATERIAL PRESENTATION April 14, SPAC Applications 1
RB&W GLOBAL LIGHTWEIGHT MATERIAL PRESENTATION April 14, 2015 SPAC Applications 1 Global Market Trend CO2 Emission Fuel Efficiency Vehicle Weight Reduction INCREASED USAGE High Strength Steels Aluminum
More informationComparative Evaluation of Resistance Made Simple Shear Connection with Bolts and With Welding
International Journal of Engineering Inventions e-issn: 78-7461, p-issn: 319-6491 Volume 3, Issue 7 (February 014) PP: 1-5 Comparative Evaluation of Resistance Made Simple Shear Connection with Bolts and
More informationSheet Metal Testing Machine Model 134
ERICHSEN Cupping Test Deep Drawing Cup Test Sheet Metal Testing Machine Model 134 Square Deep Drawing Cup Test Bore Expanding Test testing equipment for quality management Technical Description Data logger
More informationAMADA ASTRO 100 NT. Bending cell. The last service will be performed by AMADA in October 2018, before the dismantling - free of charge
AMADA ASTRO 100 NT Bending cell The last service will be performed by AMADA in October 2018, before the dismantling - free of charge Manufacturer Model AMADA ASTRO 100 NT Year of manufacture 2005 Control
More informationWire Drawing 7.1 Introduction: stock size
Wire Drawing 7.1 Introduction: In drawing, the cross section of a long rod or wire is reduced or changed by pulling (hence the term drawing) it through a die called a draw die (Fig. 7.1). Thus, the difference
More information# in 1 Metal Worker Auxiliary Operating Instructions
340 Snyder Avenue, Berkeley Heights, NJ 07922 www.micromark.com MMTechService@micromark.com Tech Support: 908-464-1094, weekdays, 1pm to 5 pm ET #86556 3 in 1 Metal Worker Auxiliary Operating Instructions
More informationJoining Metals with Stamping Dies
733563AA Joining Metals with Stamping Dies A Die Builder s Guide to BTM s sheet metal clinch joining systems. A supplement for BTM s Tog-L-Loc and Lance-N-Loc Tooling Catalogs to assist in the proper application
More informationINFLUENCE OF PILES ON LOAD- SETTLEMENT BEHAVIOUR OF RAFT FOUNDATION
INFLUENCE OF PILES ON LOAD- SETTLEMENT BEHAVIOUR OF RAFT FOUNDATION BALESHWAR SINGH Department of Civil Engineering Indian Institute of Technology Guwahati Guwahati 78139, India NINGOMBAM THOIBA SINGH
More informationLABORATORY EVALUATION OF CONCRETE-FILLED GFRP DOWELS IN JOINTED CONCRETE PAVEMENTS
LABORATORY EVALUATION OF CONCRETE-FILLED GFRP DOWELS IN JOINTED CONCRETE PAVEMENTS Scott Murison, EIT, KGS Group, Winnipeg, Manitoba Ahmed Shalaby, Associate Professor of Civil Engineering, University
More informationJoining Metals with Stamping Dies
733563 Joining Metals with Stamping Dies A Die Builder s Guide to BTM Corporation s sheet metal clinch joining systems. A supplement for BTM Corporation s Tog-L-Loc and Lance-N-Loc Tooling Catalogs to
More informationPrecision Folding Technology
Precision Folding Technology Industrial Origami, Inc. Summary Nearly every manufacturing process has experienced dramatic improvements in accuracy and productivity as well as declining cost over the last
More informationTechnical Datasheet #0051. Extrusion cutter blade design Eight pointers to a better cut finish
Technical Datasheet #0051 Blade shape & position, thickness, width, length, and bevelling & sharpening - here s a look at the critical aspects of an area too often overlooked or else taken for granted.
More informationForming - Blanking. Manufacturing Technology II Lecture 6. Prof. Dr.-Ing. Dr.-Ing. E.h. F. Klocke
Forming - Blanking Manufacturing Technology II Lecture 6 Laboratory for Machine Tools and Production Engineering Chair of Manufacturing Technology Prof. Dr.-Ing. Dr.-Ing. E.h. F. Klocke Seite 1 Content
More informationCompression vs. Fusion: The Source of Strength in Fused Sight Glasses for Chemical and Pharmaceutical Processes
Compression vs. Fusion: The Source of Strength in Fused Sight lasses for Chemical and Pharmaceutical Processes Manufacturers of sight glasses use different combinations of metal and glass to achieve a
More informationCopyright Notice. HCL Technologies Ltd. All rights reserved. A DEFINITIVE GUIDE TO DESIGN FOR MANUFACTURING SUCCESS
Copyright Notice HCL Technologies Ltd. All rights reserved. No part of this document (whether in hardcopy or electronic form) may be reproduced, stored in a retrieval system, or transmitted, in any form
More informationFolding Center XL-Center
RAS Reinhardt Maschinenbau GmbH : Compact innovation! The is a folding innovation for light gauge sheet metal profiles used mainly in the roofing and architectural industry. With 3200 mm (126") of folding
More informationThe influence of gouge defects on failure pressure of steel pipes
IOP Conference Series: Materials Science and Engineering OPEN ACCESS The influence of gouge defects on failure pressure of steel pipes To cite this article: N A Alang et al 2013 IOP Conf. Ser.: Mater.
More informationANALYSIS OF LATERAL STIFFNESS FOR INFILLED FRAME WITH OPENING
ANALYSIS OF LATERAL STIFFNESS FOR INFILLED FRAME WITH OPENING A.S. KASNALE 1 & SANJAY JAMKAR 2 Professor in Civil Engineering Department, M.S. Bidve Engineering College, Latur, India Professor in Civil
More informationPrying of a Large Span Base Plate Undergoing a Moment Load Applied by a Round Pier
Prying of a Large Span Base Plate Undergoing a Moment Load Applied by a Round Pier by Anastasia Wickeler A thesis submitted in conformity with the requirements for the degree of Masters of Applied Science
More informationdesign and trading company Manufacturer of metal forming machinery POLAND presses rolling mills punch presses
design and trading company Manufacturer of metal forming machinery POLAND presses rolling mills punch presses UPH 28 Horizontal hydraulic press - Built-in memory makes it possible to save up to 4 bending
More informationAbrasive Flow Machining ( AFM ) Semih Sancar Selçuk Ünal Yunus Kocabozdoğan
Abrasive Flow Machining ( AFM ) Semih Sancar 20622852 Selçuk Ünal 20622976 Yunus Kocabozdoğan 20519809 Goals Getting basic knowledge about AFM Clasification of AFM One-way AFM Two-way AFM Orbital AFM Application
More informationCHAPTER 2 ELECTROMAGNETIC FORCE AND DEFORMATION
18 CHAPTER 2 ELECTROMAGNETIC FORCE AND DEFORMATION 2.1 INTRODUCTION Transformers are subjected to a variety of electrical, mechanical and thermal stresses during normal life time and they fail when these
More information