52 5 N. Instructions & Parts List. From the library of: Superior Sewing Machine & Supply LLC
|
|
|
- Heather Harper
- 5 years ago
- Views:
Transcription
1 52 5 N Instructions & Parts List
2 z L.f) N L!) _J w 0 0 ~
3 INSTRUCTION BOOK FOR MODEL N 1. Starting. Attach the operation handle (No.54) to the machine and after confirming that the switch (No.56) is at the "off" position, connect the electric cord (No.72) to the machine terminal end, and also connect the other end of the electric cord to the electric source. Taking away any foreign items, if any, from the machine bed (No.30), put the operation switch on to start the machine. WARNING : In case that the motor is three phases, direction of the rotation of the knife must be as indicated by arrow on the knife cover. If it rotates in the opposite direction, please reset the lead wires one another, excepting the green colored one, in the electric source plug. 2. Cutting operation. Hold the operation handle and lift the knife guard (No.25). Put the materials in adequate thickness onto the machine bed. Then, start the cutting operation, pushing the machine forward to cut the material off. 3. Knife sharpening. Keeping the motor running, lower the grinding lever (No.39) so the grinding stone (No.78) touches the knife (No.67) and keep it grinding for a few seconds. If the knife is so worn out, it needs more sharpening. Please repeat sharpening of it in the same way as often as it is necessary. 4. Knife replacement. First, please be sure that the motor is not working. Then, make an adjustment of the knife and the position of the throat plate (No.32). If the knife is worn out, its cutting edge does not fit to the knife groove, and it has to be replaced. To remove the knife, insert the knife handle (No.65), which is one of the accessories, to the knife presser (No.14), and tum it counterclockwise. In case that the knife presser is connected too tightly, lock the small holes of the knife and the stand with a pin of about 4mm in diameter to stop the knife moving idle. To employ a new knife, align the knife to the key groove, facing its back side on to the stand. The knife has a front and back side. All other order to fit the knife is just the reverse sequence. 5. Sharpener adjustment and replacement. After assuring that the motor is not working: 1) Loosen the grinder screws (No.16-f) so the grinder adjusting pipe screw (No.17-d) can move. Turn the grinder adjusting pipe screw by hand until the grinding stone almost touches the knife. Make the same adjustment to the other grinding stone, and tighten all the grinder screws. In the adjustment, the clearance between the right and left grinding stones should be maintained at about 1 mm. 2) Remove the grinder screws (No.16-f), and take off the grinder setting studs. The grinding stones can be replaced with the new ones in the order that is a reverse sequence to their removing. The adjustment is to be made by referring to the above order, 5-1). It is advised to fit each group of parts separately to avoid erroneous fitting. 6. Maintenance and inspection. 1 ) Provide new grease to the grease cup once about a month. Please make it custom to use the special grease that is supplied with the machine. To provide the new grease, first fill the grease cup with the grease and supply a little grease to its lid. As the lid puts into the cup, the grease gradually permiates. 2) Take put the knife time by time to clean off the cut ends inside the knife back and the stand (No.28). DETAILS A~D SPECIFICATIO:\S SCBJECT TO CHA~GE WITliCUT :;OTICE.
4 Parts List for Model N Parts No B B 17 * 17-a 17-b 17-c 17-d 17-e 17-f B 25-(5) 25-(6) 25-B 25-B B Unit Parts Name Description O'ty Motor Front Housing... 1 pee. Ball Bearing Lock Nut 1 pee. Ball Bearing (6202)... 1 pee. Motor Rear Housing pee. Ball Bearing Lock Nut pee. Bail bearing (6202) pee. Set Screw for Pinion Gear pee. Pinion Soiral Bevel Gear (smal!)... 1 pee. Spiral Bevel Gear (large) pee. Washer for the above pee. Ball Bearing (B CG9)... 1 pee. Ball Bearing Lock Nut... 1 pee. Knife Retaining Nut pee. Gear Lock Screw pee. Grinder Bracket set Bracket joint pee. Stud, Washer, & Screw Emery Stone 2 sets Screw pes. Washer pes. Stud... 2 pes. Pipe Screw pes. Washer pes. Screw pes. Shaft Sack... 1 pee. Set Screw & Washer for the above2 sets Pressure Shaft (5' type) pee. Pressure Shaft (6" type)... 1 pee. Rubber Washer for the above... 1 pee. Set Screw for the above... 1 pee. Acrylite Plate pes. Set Screw for the above pes. 27 Adjustable Screw for Pressure Shaft 1 pee. 28-(5) Stand (Foot) (5" type) pee. 28-(6) Stand (Foot) (6' type) pee. 28-B-(5) Knife Slide (5" type) pee. 28-B-(6) Knife Slide (6" type) pee. 28-B-1 Set Screw for the above pes. 28-C-(5) Knife Cover (5" type) pee. 28-C-(6) Knife Cover (6' type) pee. 28-C-1 Set Screw for the above pee. 28-E Semicircular Plate pee. 29 Grease Cup pee. 29-B Collar fo the above pee. 30-(5) * Base Plate IBed) complete (5" type)... 1 pee. 30-(6) * Base Plate (Bed) complete (6" type) 1 pee. 30-a-(5) Base Plate only (5" type) pee. 30 "!-(6) Base Plate only (6" type)... 1 pee. 30-b Plate Wing only pee. 31 ~": Screw for Stand to Base Plate.. 3 pee. Parts No * 34-a 34-b 34-c B B 46 Unit Parts Name Description O'ty Throat Plate pee. Set Screw & Washer for the above... 2 sets Roller complete set sets Stud (Pin) only pes. Roller only pes. Washer only pes. Set Screw for the above pes. Stay Piece for Grinder Lever... 1 pee. Set Screw & Washer for the above 1 set Grinder Lever... 1 pee. Joint... 1 pee. Lever Spring... 1 pee. Set Screw & Washer for the above 1 set Motor Field (Slayter) With Housing (53-1)... 1 pee Rotor with Shaft pee (5) Joint Shaft for the above (5" type)... 1 pee (6) Joint Shaft for the above (6" type) pee Set Screw for the above... 2 pes. 49 Stayter Base (contact Flange)... 1 pee. 49-B Set Screw for the above... 2 pes. 50 Rotor Base (Governor) pee. 51 Governor Nut pee. 52 Governor Box (cover) pee. 52-B Set Screw for the above pes. (53-1 Motor Field (Staytor) Housing... 1 pee.) 53-2 Set Screw for the above pes. 54 Operating Handle pee. 55 Switch Box (cover) pee. 55-B Set screw for the above... 2 pes. 56 Switch for Motor pee. 56-B Cap for the above... 1 pee. 58 Set Screw for the Terminal Block pes. 60 Set Screw & Washer tor Stand to Frcnt Housing 3 pes. 63 Terminal Block... 1 pee. 57 Carrying Handle pee. 57-b Fixed Screw & Washer for the above 4 pes. 65 Knife Blade fastening Key (wrench)... 1 pee. 67-(5) Circular Knife Blade 5' diameter pee. 67-(6) Circular Knife Blade 6" diameter pee. 68 Mortar fixed Cap Screw pes. 69 Base Plate Wing Pin pee. 70 Base Plate Wing Spring... 1 pee. 70-B Set Screw & Washer for the above Spring.. 1 set 71 Set Screw for Base Plate Wing Pin... 2 pes. 72 Electric Cord with Plug pee Rubber Tube for Cord C1 pee Terminal Connector Plug... 1 pee. 78 Emery Wheel (Sharpening Stone) 2 pes.
5 Parts List(.. 525N3)
From the library of: Superior Sewing Machine & Supply LLC
I TER 1 1 Yamajin Bldg., 18, 1-chome, Hon-machi, Higashi-ku, Osaka 541, Japan P.O.Box: Osaka Higashi No. 509 Telephone: Osaka 261-3291 N3297 (7 Lines) Cable Address: "CONSEWMACH" Osaka Telex: J64459 CONSEW
WX8800 WX8700 LX5801 WX8842 WX MC30
WX8800 WX8700 LX5801 WX8842 WX8842-1 MC30 First published : August 1991 Third edition : August 2004 No. 040037 INTRODUCTION Thank you for your purchasing Kansai Special's WX Series. Read and study this
Daily Maintenance. 2. Insert bobbin cases in to rotary hooks. Make sure bobbin thread is not over 2 inches long. Close bobbin case covers.
Rotary hook 1. Open bobbin case covers and remove bobbin cases. Use brush to remove lint build up in and around rotary hooks. Compressed air may also be used. Daily Maintenance Cle aning Oiling Rotary
JARVIS. Model BR-3 Blade Reconditioner ... EQUIPMENT TABLE OF
- Model BR-3 Blade Reconditioner EQUIPMENT SELECTION.......... Ordering No. TABLE OF CONTENTS............................ Page Model BR-3 (100 mm Blade) 115V/60Hz............ 4011003 220V/50Hz............
SECTION 9: PARTS. Table Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION
SECTION 9: PARTS Table Breakdown 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 23 25 17 26 27 8 1 P0675001 CAP SCREW M8-1.25 X 30 15 P0675015 SUPPORT BLOCK 2 P0675002 TABLE SUPPORT BLOCK
Tapping Screw (W/Flange) 46 Cord Armor 47 Tube (D) 48 Cord. 45 Cord Clip. Tapping Screw (W/Flange) 10 Gear Cover Ass'y. 12 Socket (B) Ass'y
W8VB The exploded assembly drawing should be used only for authoized service center. W8VB Item No. Part time 1 Magnetic Hex. Socket 2 Sub Stopper 3 O-Ring (S-16) 4 Locator (A) 5 Lock Sleeve (A) 6 O-Ring
OPERATION-LUBRICATION-CARE
OPERATION-LUBRICATION-CARE KR-A CUTTER 1 ~--B E FO R E--U S E...... i A. Remove the bolt fixing Switch Link (R-66) temporanly and f1t Operating Handle (R-67). B. Insert Attachment Plug (R-19) into Terminal
RYOBI 10 IN (254 MM) TABLE SAW MODEL NO. BT REPAIR SHEET
RYOBI 0 IN (2 MM) TABLE SAW MODEL NO. BT00- REPAIR SHEET 2 RYOBI 0 in. (2 mm) TABLE SAW - MODEL NO. BT00- FOR MITER TABLE ASSEMBLY, REFER TO FIGURE B FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE E FOR RIP
SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" SLIDING COMPOUND MITER SAW
PAGE 1 OF 6 BASE ASSEMBLY 00 0 CATALOG NO. EXAMPLE: SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 6955-20 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510 M5 x 12mm Flat Head T-20 Screw (5) 3 05-81-0135
RYOBI 10 in. (254 mm) TABLE SAW MODEL NO. BT3100 REPAIR SHEET
RYOBI 0 in. (4 mm) TABLE SAW MODEL NO. BT00 REPAIR SHEET FOR MITER TABLE ASSEMBLY, REFER TO FIGURE B FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE E FOR RIP FENCE ASSEMBLY, REFER TO FIGURE C FOR MOTOR ASSEMBLY,
VARIABLE SPEED WOOD LATHE
MODEL MC1100B VARIABLE SPEED WOOD LATHE INSTRUCTION MANUAL Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Version: 2015.02.02
FBX1104P FBX1104 FBX1106P FBX1106
FBX1104P FBX1104 FBX1106P FBX1106 Second edition : September 2004 No. 040037 INTRODUCTION Thank you for your purchasing Kansai Special's FBX Series. Read and study this instruction manual carefully before
GENERAL OPERATIONAL PRECAUTIONS PRECAUTIONS ON USING CUT-OFF MACHINE
GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
OPERATOR S MANUAL FOR MODEL BLADE GRINDER
OPERATOR S MANUAL FOR MODEL 88-021 BLADE GRINDER Table of Contents Page Blade Grinder Safety and User Instructions 2 Unpacking the Grinder 5 Assembling the grinder 6 Adjusting the grinding angle 8 Adjusting
SINGER 531B-8BL. From the library of: Superior Sewing Machine & Supply LLC
SINGER 53B-8BL PERSPECTIVE THREAD TENSION, GUIDE, NEEDLE PLATE i SINGER 4 THREAD TENSION, GUIDE, NEEDLE PLATE 3 Fig. No. Parts No. Quantity Name of Parts Fig. No. Parts No. Quantity Name of Parts 0698
REPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer
Cat. No. 9-0 SDS Max Demolition Hammer Cat. No. -0 SDS Max Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 8-9-0 d 000 8-9-0 d Special Tools Require Forcing
SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27B
PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS = Part number change from previous service
Coolant Tank Screen Leg Idle End Lockwasher 64 B-015B Leg Drive End Machine Screw 1/4-20 x 3/4 Round Head
Always give model number, serial number and part number when ordering repair parts. BED, COOLANT & DASH POT PARTS LIST (Cont'd.) REF NO. PART NUMBER DESCRIPTION 19 B-077 Vise Slide Block 20 B-045 Vise
OPERATIONS MANUAL. Port-O-Slitter
Tapco Products Company The World Leader in Specialty Tools for the Professional Port-O-Slitter OPERATIONS MANUAL General instructions, set up, accessories and guide to using your portable precision slitting,
Click Here to Go Back
Click Here to Go Back Fig. -94 Fig. -97 CC42D 10. Remove the cap screw securing the gear shift stopper plate pin retainer; then remove the retainer. Fig. -95 CC45D 12. Remove the link arm and account for
Angle Grinder MODEL 9553B MODEL 9555B
ENGLISH Angle Grinder MODEL 9553B MODEL 9555B 006649 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR
RYOBI 10 in. TABLE SAW - MODEL NO. BT3000
FOR MITER TABLE ASSEMBLY, REFER TO FIGURE 0 RYOBI 0 in. TABLE SAW - MODEL NO. BT000 FIGURE 5: 0 in. TABLE SAW FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE FOR RIP FENCE ASSEMBLY, REFER TO FIGURE FOR MOTOR
Parts List for Type 1
1 422190430001 FENCE BODY 1 2 901010600677 CAP SCREW 2 3 904010331451 WASHER 3 4 901010600605 CAP SCREW 2 5 904010101604S STEEL WASHER 2 6 422040105002 REAR SLIDE BLOCK 1 7 905040714459 STEEL PIN 1 8 928010414118
GENERAL OPERATIONAL PRECAUTIONS PRECAUTIONS ON USING DISC GRINDER
GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
CONTENTS PRECAUTIONS BEFORE STARTING OPERATION PREPARATION FOR OPERATION CAUTIONS ON USE OPERATION
CONTENTS PRECAUTIONS BEFORE STARTING OPERATION ------------------------------------- 1 PREPARATION FOR OPERATION 1. Adjustment of needle bar stop position ---------------------------------------------------------
SERVICE MANUAL AND PARTSLIST
SERVICE MANUAL AND PARTSLIST Next 20 CONTENTS WHAT TO DO WHEN... 1~3 SERVICE ACCESS FACE COVER... 4 TOP COVER... 4 BASE COVER... 5 REAR COVER... 6 FRONT COVER... 7 MECHANICAL ADJUSTMENT NEEDLE THREAD TENSION...
TECHNICAL INFORMATION
TECHNICAL INFORMATION P 1 / 11 Model No. Description CONCEPT AND MAIN APPLICATIONS Specification Standard equipment TCT saw blade... 1 Rear table set (exclusively Europe, Turkey, South Africa..1 2704 This
HOLE CUTTER SHARPENER ASSEMBLY & SERVICE MANUAL
HOLE CUTTER SHARPENER ASSEMBLY & SERVICE MANUAL WARNING You must thoroughly read and understand this manual before operating the equipment, paying particular attention to the Warning & Safety instructions.
ITEM NO. PART NO DESCRIPTION QTY.
PUMP MAINTENANCE ITEM NO. PART NO DESCRIPTION QTY. 1 52002 Center Case 1 2 52052 Back End Plate 1 3 52051 Front End Plate 1 4 55090 Octagonal Nut 1 5 53001 Idler Gear 1 6 53002 Drive Gear 1 7 28062 Bushing
400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
VARIABLE SPEED WOOD LATHE. Model DB900 INSTRUCTION MANUAL
VARIABLE SPEED WOOD LATHE Model DB900 INSTRUCTION MANUAL 1007 TABLE OF CONTENTS SECTION...PAGE Technical data.. 1 General safety rules....1-3 Specific safety rules for wood lathe.....3 Electrical information.4
INSTRUCTION BX1425P,PSM,PTV BX1433P,PSM,PTV BX1025P,PSM BX1033P,PSM. No First published : November 1997
INSTRUCTION Industrial Sewing Machines BX1425P,PSM,PTV BX1433P,PSM,PTV BX1025P,PSM BX1033P,PSM First published : November 1997 No. 970112 INTRODUCTION Thank you for your purchasing Kansai Special's BX
HYDRAULIC CONTROL DETAILS PARTS LIST
Always give model number, serial number and part number when ordering repair parts. HYDRAULIC CONTROL DETAILS PARTS LIST REF NO. PART NUMBER DESCRIPTION 1 101939 Hydraulic Tank 2 101940 Hydraulic Tank
HANDHOLE SEAT GRINDER
1041-1601 HANDHOLE SEAT GRINDER OPERATING INSTRUCTIONS & SERVICE MANUAL Rev: A, 9/17/2007 TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE USER MUST READ AND UNDERSTAND OPERATOR S MANUAL. Thomas C. Wilson,
PFAFF. rom the library of: Superior Sewing Machine & Supply LLC. Service Manual Justieranl. engi. 7.92
PFAFF 5642 Service Manual 296-12-13925 Justieranl. engi. 7.92 Notes on safety The machine must only be commissioned in full knowledge of the instruction book and operated by persons with appropriate training.
Thomas Scientific Swedesboro, NJ U.S.A.
Thomas Scientific Swedesboro, NJ 08085-0099 U.S.A. Wiley Mini Mill 3383-L10 (115 V, 60 HZ) USE AND CARE OF CATALOG NUMBER: 3383-L10 Wiley Mini Mill (115 V, 60 HZ) PRELIMINARY 1. Mill has been properly
ELECTRIC TOOL CORPORATION
Cat. No. -0 / Hex Demolition Hammer Cat. No. 0-0 Spline Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 -9-00 d 000 -9-00 d SpecialTools Require Forcing discs
OPERATIONS MANUAL. Port-O-Slitter
OPERATIONS MANUAL Port-O-Slitter General instructions, set up, accessories and guide to using your portable precision slitting, rib forming and perforating system Saves hours on large siding jobs! Featuring:
MODEL RA-2500N RADIAL ARM SAW
1 6130089 HEX. NUT (L.H.T.) W5/8"-18UNF 2.18 2 6900549 WASHER 1.78 3 6080529 ARBOR COLLAR 31.02 4 6760117 OILLESS METAL 1.57 5 9270612 CLAMP SCREW M6 X 12 0.19 6 9220625 HEX. SOCKET HEAD BOLT M6 X 25 0.22
SPARE PARTS LIST MODEL NO PAGE 1 ITEM PART NO. DESCRIPTION QTY NOTE
PAGE 1 001 342186-7 SWITCH PROTECTOR 1 002 911118-1 PAN HEAD SCREW M4X12 6 003 155512-9 SWITCH PLATE 1 004 651757-2 SWITCH ABK266 1 006 685712-2 SPONGE SHEET 60X60 1 007 911118-1 PAN HEAD SCREW M4X12 1
12mm (Max) 6mm (Max) 82mm (Max) 12mm (Max) 6mm (Max)
1 1 2 2 3 3 82mm (Max) 12mm (Max) 12mm (Max) 6mm (Max) 4 4 5 6 8 6mm (Max) 0.5 0mm 1 5 6 7 7 8 9 9 A = B 10 11 12 D B 1 13 14 15 0 C A D E 16 17 18 F G D B N H J G I K 19 A 20 G L 21 C K 1mm L M 1mm 22
488 PARTS LIST 1 3 SCREWS FOR NO. 2 2 FLYWHEEL CAP 3 FLYWHEEL 4 END NUT FOR NO. 10 5 BALL BEARING FOR NO. 3 (1 st ) 6 BALLBEARING FOR NO. 3 (2nd) 7A CLUTCH RACE KEY 7B CLUTCH RACE 7C CLUTCH SPRING 7D 7
MODEL T28173/T28174 ROLLER TABLES INSTRUCTIONS
MODEL T28173/T28174 ROLLER TABLES INSTRUCTIONS FOR MODELS MFD. SINCE 10/17 For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Rails Rollers Reversible
Code Product Qty 1 Top Vertex 3 2 Hot End Housing 1 3 Bottom Vertex 3 4 Print Platform Lock 3 5 End Stop Holder 3 6 Filament Feeder Motor Bracket 1 7
List of Parts Code Product Qty 1 680mm Extrusion 3 2 Power Supply 1 3 240mm Extrusion 9 4 42mm Nema 17 Stepper Motor 3 5 Slider-Hotend Connecting Rod 6 6 48mm Nema 17 Stepper Motor 1 7 Linear Rail with
MACHINE PARTS CHART SINGER*
Form U3174 (Rev. 983) Part No. 643197 002 (Rev. 1) MACHINE PARTS CHART for SINGER* 220 220 U2 U3 * A Trademark of THE SINGER COMPANY Copyright 1980 THE SINGER COMPANY All Rights Reserved Throughout the
SPARE PARTS LIST MODEL NO. LB1200F PAGE 1 ITEM PART NO. DESCRIPTION QTY NOTE
PAGE 1 001 JM21000018 HEX.SOCKET HEAD SCREW M5X12 4 002 JM21000019 SPRING WASHER 5 4 003 JM21000020 FLAT WASHER 5 4 004 JM21000021 UP COVER COMPLETE 1 005 JM21000025 MICRO SWITCH FIX PANEL A 1 006 JM21000026
GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
General Four-Way Operation, Maintenance & Service Manual
General Four-Way Operation, Maintenance & Service Manual SCOPE Included in the following pages you will find assembly drawings, exploded views, parts lists, assembly tips, operational descriptions and
Replacing the Reciprocator on an SWF Multi-head.
Replacing the Reciprocator on an SWF Multi-head. Follow the instructions below to replace the reciprocator in the SWF multi-head machines. The tools required are found in the tool kit that came with the
From the library of: Superior Sewing Machine & Supply LLC
ROUND KNIFE CUTTING MACHINE LIGHTNING MODELS 334, 354, 355 and 356 WASHINGTON STREET, BUFFALO 3, N. Y LUBRICATION AND CARE TO ADJUST EMERY WHEELS i m When Emery Stones wear away so that they are too far
INSTRUCTION BOOK AND PARTS LIST
Rag Cutter MODEL WE WARNING This machine is equipped with a very sharp knife. Keep hands, arms, and hair away from the knife area at all times. Misuse of this machine or failure to follow all safety instructions
ADJUSTMENT MANUAL. This adjustment manual applies to machines from the following serial numbers onwards: #
45 46 ADJUSTMENT MANUAL This adjustment manual applies to machines from the following serial numbers onwards: # 6 500 4 96--9 00/00 Justieranleitung engl. 0. The reprinting, copying or translation of PFAFF
DRILL GRINDING ATTACHMENT
DRILL GRINDING ATTACHMENT To suit TM6025Q TOOL AND CUTTER GRINDER OPERATION S MANUAL 1 0º 270º 90º 180º INTRODUCTION Before grinding any cutters, you must set up the attachment to suit the type of cutter
TP1300 OWNERS MANUAL 13 INCH THICKNESS PLANER WITH LEGSET. For Your Safety: Read all instructions carefully Save this manual for future referenece
TP00 OWNERS MANUAL INCH THICKNESS PLANER WITH LEGSET For Your Safety: Read all instructions carefully Save this manual for future referenece SP Printed in Taiwan Parts List for " Thickness Planer Model
J-3-D PART NO DATE:
37-380 & 37-877 8 PROFESSIONAL JOINTER J-3-D PART NO. 909563 DATE: 05-12-04 Page1/ J-3-D /DEB REPLACEMENT PARTS * 1345487 CUTTERHEAD ASSY, INCL: 1 1340196 KNIFE SCREW 2 1345488 BAR 3 37-355 KNIVES (SET
GENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Fifth Wheel Adapter Titan 999T5 W4198 KIT CONTENTS: Item Qty. Part Description Service Part Number A 1 Fifth Wheel Adapter
EMS-2025scl 230v. Sliding Compound Mitre Saw Fig.1. Revision Date 26/01/2006
Fig.1 Fig.2 701 inc 2,702,703,704 1 Base 93 089100102700 Space washer Base Assembly Parts (A) 30.23 94 Screw, for base, 45 152 Miter scale label, 2 089100102002 Rubber feet 0.10 702 Pivot Shaft & Screw
Due to possible damage in shipping, the vertical stop assembly has been removed from this machine.
Due to possible damage in shipping, the vertical stop assembly has been removed from this machine. To assemble, insert the threaded rod through the shroud opening in the top of the machine. Start the four
INSTRUCTION BOOK AND PARTS LIST
RUBBER SLITTER MODEL RS2 WARNING Safety glasses must be worn at all times when operating or servicing this equipment. Please read completely before attempting to operate your RS2 Cutting machine. WARNING
SERVICE MANUAL FOR DT4-B281 FOUR NEEDLE DOUBLE CHAIN STITCHER WITH PULLER. From the library of: Superior Sewing Machine & Supply LLC
SERVICE MANUAL FOR DT4-B281 FOUR NEEDLE DOUBLE CHAIN STITCHER WITH PULLER Table of Contents [A] Model Plate Display... 1 [B] Specifications... 2 [C] Description of Mechanism... 3 [) Needle bar mechanism...
Model LS1018 Parts List A = Standard Equipment 〇 = Circuit Diagram
LS1018 7-14 103 104 105 106 97 99 100 110 109 63 85 96 200 107 90 2 199 108 37 89 91 92 93 94 31 74 75 73 140 70 121 15 254 255 113 215 236 116 114 115 196 258 195 118 197 119 259 117 203 253 67 95 112
INSTRUCTION MANUAL AND PARTS LIST MODEL 14-10
VERTICAL BAND SAWS INSTRUCTION MANUAL AND PARTS LIST MODEL 1-10 DAKE/PARMA WHEN ORDERING PARTS GIVE COMPLETE SERIAL NUMBER OF MACHINE GIVE PART NUMBER AND NAME GIVE AMOUNT REQUIRED Unless the above data
EllisSaw.com. EllisSaw.com P.O. Box Verona, WI
P.O. Box 9019 Verona, WI 9-019 GENERAL OPERATING & SAFETY INSTRUCTIONS * READ INSTRUCTIONS BEFORE USE * CAUTION: Disconnect power supply cord from power source when doing repair work or changing belt.
FBX-PA-2AC. Third edition : April No
FBX-PA-2AC Third edition : April 2006 No. 060058 INTRODUCTION Thank you very much for purchasing Kansai Special FBX series. Read and study this Instruction Manual carefully before you start any of the
LU6X-130 Instructions and Parts List (including LU6X Basic) Operating Instructions
LORTONE LU6X-130 Item # 061-092 LU6X Basic Item # 061-090 LU6X-130 Instructions and Parts List (including LU6X Basic) Operating Instructions Introduction The LU6X is one the most versatile pieces of equipment
1822-I. Spindle Assembly. Pipe and Bolt Threading Machine. Ridge Tool Company/Elyria, Ohio, U.S.A. 2* 3 4 5* * *
-I Pipe and Bolt Threading Machine Spindle Assembly * * * 0 * * * 0 * * 0* * * Rear Cover * Screw () * Washer () Top Cover w/clips (Includes,, ) * J Clip () Front Cover * Screw () Pivot Rod Support ()
RYOBI. 10 in. (254 mm) TABLE SAW MODEL NO. BTS15 REPAIR SHEET
RYOBI 0 in. ( mm) TABLE SAW MODEL NO. BTS REPAIR SHEET FIGURE A 0 0 0 0 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding
Legacy Woodworking Machinery a division of Phantom Engineering. The Legacy CNC. Assembly Manual
Legacy Woodworking Machinery a division of Phantom Engineering The Legacy CNC Assembly Manual New Orientation of the Legacy Step one: Re-orientation of the machine Remove the X-axis screw and supports.
Inspection. Assembly Install the springs. 1. Discard the 0-rings. 2. Clean all parts in cleaning solvent.
6010-34 Inspection 3. Install the springs. 1. Discard the 0-rings. 2. Clean all parts in cleaning solvent. 3. If spring test equipment is available, check the tension of each spring according to the specifications
" PLUG AERATOR. Model No. Safety Assembly Operation Maintenance Parts. CAUTION: Read Rules for Safe Operation and Instructions Carefully
owner s manual Model No. 45-0383 48" PLUG AERATOR CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts the fastest way to purchase parts www.speedepart.com
MS25 OPERATION MANUAL
SAFETY INSTRUCTIONS SPECIFICATIONS OPERATING INSTRUCTIONS MAINTENANCE ADJUSTMENTS REPLACEMENT OF PARTS MS25 DIAGRAM MS25 PARTS LIST MS25 OPERATION MANUAL SAFETY INSTRUCTIONS Please read these instructions
Quick Set Dovetail Jig
Quick Set Dovetail Jig FOR HELP OR ADVISE ON THIS PRODUCT PLEASE CALL OUR CUSTOMER SERVICE HELP LINE : 01509 500359 THE MANUFACTURER RESERVES THE RIGHT TO ALTER THE DESIGN OR SPECIFICATION TO THIS PRODUCT
ELECTRIC SLIP ROLL MACHINE. Model: ESR-1300X2.5/ESR-1300X4.5 ESR-1550X3.5/ESR-1580X2.0
ELECTRIC SLIP ROLL MACHINE Model: ESR-1300X2.5/ESR-1300X4.5 ESR-1550X3.5/ESR-1580X2.0 Operation Manual Table of contents I MAIN SPECIFICATION...2 II SAFETY INSTRUCTIONS.. 2 III OPERATION INSTRUCTIONS..4
Before use please read & understand this manual, paying particular attention to the safety instructions.
OPERATOR S MANUAL AND PARTS LIST 12 HAND PUSH ROLLER MOWER - THHMR Sales & Helpline 01793 333220 www.thehandy.co.uk Before use please read & understand this manual, paying particular attention to the safety
OPERATIONAL MANUAL V1.0. Removing/Replacing Blades
OPERATIONAL MANUAL V1.0 BLUEROCK WS-212 Wire Stripper Removing/Replacing Blades CAUTION!! IMPORTANT!! DANGER!! WARNING!! DISCONNECT MACHINE FROM POWER BEFORE PROCEEDING!! Estimated Completion Time: 90
Assembly Instructions
P/N 8650/8655 Assembly Instructions NOTE: Your Sherline CNC Cam Grinder is double boxed and secured to a wooden shipping frame. Upon delivery, check the outer box for damage. If the box is damaged, take
INSTRUCTION. Industrial Sewing Machines V7100/D,DE,F,ML W8100/D,DE,F,C W8042 W V7002-1S W8103-1S. No Third edition : March 2001
INSTRUCTION Industrial Sewing Machines V7100/D,DE,F,ML W8100/D,DE,F,C W8042 W8042-1 V7002-1S W8103-1S Third edition : March 2001 No. 010012 INTRODUCTION Thank you for your purchasing Kansai Special's V.W
25-200H. 12 Planer / Jointer. with Helical Cutterhead. Parts List.
25-200H 12 Planer / Jointer with Helical Cutterhead 4001824 Parts List www.rikontools.com CABINET ASSEMBLY PARTS EXPLOSION & PARTS LIST KEY NO. DESCRIPTION KEY NO. DESCRIPTION 1 Pan Head Screw M6x12 P25-200H-1
Number Wheeler P/N Description Set Rex P/N Notes Base 1 J Support, Right 1 J Support, Left 1 J Nut (M8)
1 603500 Base 1 J001 2 603501 Support, Right 1 J002 3 603502 Support, Left 1 J003 4 600328 Nut (M8) 4 5 600130 Spring Washer (8mm) 4 6 600344 Roll Pin (M6x30) 4 7 600129 Socket Hd Cap Screw (M8x25) 4 8
SERVICE MANUAL For UHR and VR series
SM-H0004_E Rev.1 SERVICE MANUAL For UHR and VR series Straight Handpiece Parts List No. UHR35: D-079 UHR50T: D-061 UHR50C: D-062 VR: D-036 VR-E: D-082-1- Notice This manual applies to both UHR series and
-- Gym Glide -- (Recreational Game Standard) Installation Instructions
-- Gym Glide -- (Recreational Game Standard) Installation Instructions Call Jaypro Sports Equipment at 1-800-243-0533 during regular business hours for technical support. www.jaypro.com Rev- Page 1 of
Operating Instructions
Operating Instructions Holding the material against the angle gauge slide it into the forming head. Be sure that the material remains against the gauge until work is finished. NOTE: This machine will handle
STARTING SERIAL NUMBER PARTS LIST FOR. Wellsaw MODEL 600 METAL CUTTING BAND SAW
STARTING SERIAL NUMBER 11075 PARTS LIST FOR Wellsaw MODEL 600 METAL CUTTING BAND SAW Wellsaw 2829 N. Burdick, Kalamazoo, MI 49004 Phone: 269-345-1132 Fax: 269-345-0095 Rev 171005 INSTALLATION, OPERATION
Model MFC-2 Split Frame Clamshell Operation and Parts Manual
Model MFC- Split Frame Clamshell Operation and Parts Manual Corporate H&S Tool, Inc. Mail: P.O. box Wadsworth, OH Shipping: Weber Dr. Wadsworth, OH U.S.A. Tel: +-0--0 Fax: +-0-- www.hstool.com e-mail:
Giraud Tool Company, Inc.
Motor Upgrade for Gracey Trimmer This package is intended to allow the user to upgrade their Gracey trimmer with a higher rpm motor and convenience features not found in the production offering. This upgrade
LISTA DE REFACCION MODELO LS1018L PAGINA 1. Pos. NUMERO DESCRIPCION Cant. NOTA
PAGINA 1 001 JM23100006 CROSS HEAD SCREW M5X20 2 002 JM23100007 FLAT WASHER 5 2 003 JM23100008 PAD 4 004 JM23100009 LOCKNUT M10 1 005 JM23100010 FLAT WASHER 10 2 006 JM23100300 BASE COMPLETE 1 INC. 7 007
Assembly Instructions
Assembly Instructions 10 CONTRACTOR TABLE SAW Model No. 351.218330 Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A. www.sears.com/craftsman 31624.00 Draft (10/08/09) UNPACKING The
Bead Roller Operating, Servicing, and Safety Instruction Manual
Bead Roller Operating, Servicing, and Safety Instruction Manual CAUTION: Read and Understand These Operating, Servicing, and Safety Instructions, Before Using This Machine. 1-800-67-26 10 Cooperative Way
Geology, Prospectors, Mining, Metallurgy, Assaying, Environmental, Geotechnical
LEGEND INC. Geology, Prospectors, Mining, Metallurgy, Assaying, Environmental, Geotechnical 988 Packer Way Sparks, NV 89431 Tel: (786) 786-3003 Fax: (775) 786-3613 Email: info@lmine.com Web: www.lmine.com
Thorvie Instructions Always wear eye protection and do not wear loose clothing when operating machinery. FOR AV- 41 ICE AUGER MACHINE
FOR AV- 41 ICE AUGER MACHINE 1. Please study video and all instructions before proceeding to grind. For Mora, Jeffy and Eskimo blades use the 6 brown resin bond wheel. Mount with washer and left-hand nut
Contents. I'DANGER - To reduce the risk of "SAVE THESE INSTRUCTIONS" This knitting machine is for home use. IIIMPORTANT SAFETY INSTRUCTIONS"
Contents Names of Parts 1 How to Assemble the Motor Driving Unit 3 Function of Each Part 12 1. Name of Part 12 2. Explanation of Each Part 12 Operation Step 18 Warn ing 19 When you use Double bed colour
Basic steps to time the Gammill quilting machine s rotary sewing hook
Basic steps to time the Gammill quilting machine s rotary sewing hook 1.) Turn the machine off and unplug it. 2.) With the needle bar in the raised position, remove the bobbin and bobbin case. 3.) Remove
How to program the digital speed display (This is factory set and will only need to be programmed if the unit is replaced)
How to program the digital speed display (This is factory set and will only need to be programmed if the unit is replaced) 1. Press and hold the set button (top left corner) until the display shows Fun
PLATE JOINER 4 INCH. ASSEMBLY and OPERATING INSTRUCTIONS. Distributed Exclusively by Harbor Freight Tools
PLATE JOINER 4 INCH 38437 ASSEMBLY and OPERATING INSTRUCTIONS Distributed Exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd., Camarillo, CA 93011 Copyright 1998 by Harbor Freight Tools. All rights
SERVICE MANUAL. Sewing Machine. Copyright 1976 The Singer Company Aii Rights Reserved Throughout the World *A Trademark of THE SiNGER COMPANY
1 SERVICE MANUAL SINGER Sewing Machine 121D200A Copyright 1976 The Singer Company Aii Rights Reserved Throughout the World *A Trademark of THE SiNGER COMPANY Form 21624 (876) Printed In U.S.A. LUBRICATION
RYOBI 10 in. TABLE SAW MODEL NO. BTS16 REPAIR SHEET
RYOBI 0 in. TABLE SAW MODEL NO. BTS REPAIR SHEET FIGURE A FIGURE E FIGURE H FIGURE C FIGURE D 0 0 FIGURE B 0 0 NOTE A WARNING: Improper electrical repair of the table saw can result in damage to the drive
N. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Dump Body tarping system. With tarping systems
MODEL RA-200N RADIAL ARM SAW
ITEM NO PART NO DESCRIPTION PRICE 1 6130089 HEX. NUT (L.H.T.) W5/8"-18UNF 2.18 2 6900079 CONICAL SPRING 16.3 X 31.5 X 1.2 0.78 3 6940444 OUTER FLANGE 4.49 4 6940443 INNER FLANGE 4.91 5 6100509 PARALLEL
Agricultural Mechanics and Technology Power Tool Safety Rules
Agricultural Mechanics and Technology Power Tool Safety Rules Name: BAND SAW Use: Cutting curves, circles and irregular shapes. 1. Use clean SHARP blades. 2. The teeth should always point DOWN. 3. Adjust
WSG 8-115; 8-125; P; WSG ; WSG P; WSG PS; WSG P; WSG 15-70Inox
Repair instructions Page of 47 Contents. Models described 2. Technical data 3. Notes and requirements 4. Tools required 5. Lubricants and auxiliary substances required 6. Disassembly 7. Assembly 8. Connection