KuraStone TM Installation Guide
|
|
- Virginia Wilson
- 5 years ago
- Views:
Transcription
1 Installation Guide Read these installation guidelines completely and thoroughly before beginning installation. Construction Requirements KuraStone pieces can be installed on braced wood or steel stud (18 GA or heavier) construction spaced at 16 o.c.. It is required that plywood sheathing or APA rated 7/16 or thicker OSB (oriented strand board) be used to ensure fastener holding power. Product Inspection Inspect all products thoroughly prior to installation. Do not install any product which may have been damaged in shipment or displays damage to the primer or finish coat. Contact your local dealer or Nichiha Customer Service toll-free at immediately, should you have a question about your order. WRB is required when installing KuraStone. Use a dark or black fluidapplied WRB over sheathing or use a code-approved WRB covered with a layer of 15-lb. black felt as defined by the 2012 IRC. Refer to local building codes. Nichiha is not liable for water infiltration. All openings must have appropriate flashing (such as water-proofing tape) to prevent moisture penetration. Follow manufacturer s guidelines and all local building codes. Please consult with your local dealer or Nichiha directly when using KuraStone on large projects, such as buildings taller than 45 or greater than three (3) stories. Special reinforcements may be required. Plywood/OSB Sheathing Starter Corner Pieces 1
2 Storage and Handling, Minimum Clearances and Cutting, Fastening, Finishing and Maintenance Storage and Handling KuraStone MUST be stored flat, and off the ground prior to installation. Storing siding on pallets is recommended. KuraStone MUST be kept dry, and stored in a covered area or covered with wrap before installation. Carry products on edge. Do not carry or lift KuraStone flat. Improper handling may cause damage or cracking. Nichiha is not liable for damage caused by improper storage or handling. Minimum Clearances Always maintain a minimum 2 clearance between KuraStone and steps, driveways and decking products. When installing KuraStone pieces leave a minimum of 6 from soil grade or 2 from hard surface to the bottom of the starter track and pieces. At roof and wall junctures and in accordance to roofing manufacturer s instructions, flashing and counterflashing is required. KuraStone pieces must be installed with a minimum 1 clearance from roofing. Cutting Always cut KuraStone pieces outside or in a well-ventilated area. Do not cut KuraStone in an enclosed area. Always cut pieces from the front to minimize chips on face. Always wear safety glasses and NIOSH/OSHA-approved respirator whenever cutting, drilling, sawing, sanding, or abrading pieces. Refer to the safety information in these instructions for more details. Use a miter saw with a diamond-tipped fiber cement or masonry blade when cutting KuraStone. Fastening Corrosion resistant screws such as stainless steel or hot-dipped galvanized wood screws, that are appropriate to local building codes and practices, must be used to fasten clips to sheathing. Nichiha is not liable for the corrosion resistance of fasteners. Do not use fuel-cell, pneumatic, powderactuated, aluminum, staples, nails or fasteners that are not rated or designed for intended use. Use a minimum 1-1/2, fully-threaded, #8 or greater wood screw. DO NOT USE NAILS FOR FASTENING KuraStone pieces. Finishing and Maintenance Use exterior-grade, high-quality sealant that complies with ASTM C-920 for all gaps that require filling with sealant. Follow manufacturer s written instructions for use. All field cut edges must be covered with sealant or paint. Any dents, chips, scratches, etc. on KuraStone shall be filled with exteriorgrade cementitious filler or patching. Follow manufacturer s instructions for use. 2
3 KuraStone Storage Piece Options and Handling Accessories KuraStone Piece Options KuraStone pieces are available in three (3) colors Mountain, Desert and Canyon. All piece options are available in all colors. Pieces are designed with no dedicated top or bottom, so that you can flip pieces to ensure a random pattern. (Refer to table on page for dimensions) KuraStone Wall Pieces KuraStone wall pieces are not ship-lapped, nor are they sealed on top and right edges as Nichiha fiber cement panel products. KuraStone pieces feature grooves on four sides, so that clips and starter track can be inserted into any side. Wall pieces are 6 in height and come in three(3) lengths, 10-1/4, 15-3/8 and 25-5/8. When installing pieces randomly use the different lengths in order to stagger piece seams on the wall. One pack contains 3 long, 2 short and 2 medium pieces. KuraStone Pre-Manufactured Outside Corner Pieces Available in all colors, each KuraStone Outside Corner is manufactured with a short and a long side. Flip corners on each course so that a long side always aligns with a short side, and continue the length of the corner. Wall Pieces KuraStone Accessories KuraStone clips, starter track and spacer can be used with all KuraStone pieces KuraStone Starter Track / FA100B KuraStone Starter Track is steel with pre-drilled fastener holes spaced approximately 1 o.c. FA100B Starter Track features weep holes spaced approx. 6 o.c. The 10- foot long, 2-3/8 high track comes 10 to a package. KuraStone pieces should sit flush with the starter track. Pre-Mitered Outside Corner Pieces KuraStone / JE602/JE720CA The KuraStone clip can be used either horizontally or vertically on all KuraStone pieces. The clip measures approximately 3.5 by 2 (nominal), and come 50 to a box. 3/16 (FS1005) & 3/8 (FS1010) Spacer (5mm and 10mm actual, respectively) The 3/16 and 3/8 green plastic spacer is used to maintain a consistent sealant gap and for use behind pieces to ensure correct distance and ensure panel stability. Spacer is 48 in length. Starter Track Spacer KuraStone - JE602 KuraStone - JE720CA 3
4 Layout Planning Storage and and Installing Handling Starter Track Layout Planning Layout piece placement on paper or set pieces on flat surface prior to installation. Create a stair-step-like stagger with large and small pieces in each course. Define a pattern going up the wall so that the 4th or 5th course is the same as the first. Avoid having seams line up within two rows of one another. Installing Starter Track The Nichiha Starter Track (FA100B) must be level and attached at a minimum of 6 above finished soil grade or per local building codes (use a level to verify). When installing over a hard surface such as driveways or sidewalks, a 2 clearance is acceptable. Fasten starter track 8 o.c. into sheathing and over WRB. Install flashing tape overlapping the starter track to control moisture penetration, or per WRB manufacturers instructions. Fasten starter track with corrosion resistant #8 or greater fully-threaded Plywood/OSB Sheathing Starter Installing Starter Track 4
5 Storage Install Panel and Handling Courses Install First Panel Course KuraStone wall pieces do not have a dedicated top or bottom. Flip pieces as needed to ensure that stone pattern appears random and courses do not repeat within 4, or less, courses. Place the first course of pieces into the starter track. A rubber mallet or block of wood may be used to seat the pieces firmly in place and tighten. Do not hammer directly anywhere on the KuraStone pieces, as direct contact may cause cracks, gouges or chipping. Installing Panel Courses Place a clip at the top of each vertical joint, and place a clip at the center of the bottom of every piece (see illustration below). Attach using appropriate screws Fit the bottom groove of the piece tightly into the clip below it and continue installing course in accordance with these instructions. Fit pieces tightly together on both horizontal and vertical joints ensuring that piece edges are properly butted together. Set KuraStone by tapping the edge with a block of wood until piece fits tightly. Attach KuraStone at the top of all vertical joints with (JE602/ JE720CA). Use the claw end of a hammer to set clip tightly in place. Ensure first course is level. Plywood/OSB Sheathing Water Proofing Barrier (Black) Additional Vertical Joint Detail An additional clip is required at the center of the bottom of each piece Horizontal Joint Detail must be at the center of the joint 5
6 Storage Outside and Corners Handling Outside Corners Do not install the KuraStone outside corner pieces first. Install them at the same time as the same-coursed pieces. Install the pre-mitered outside corner and butt adjacent to KuraStone wall piece tightly to it. Attach a clip at top of the vertical joints on either side of corner, as well as a clip 2-3 from outside corner on the long length side. Long Returns When cutting pieces is necessary, cut the adjacent KuraStone wall piece, not the corner piece. Short Returns Flip corners on each course so that a long side always aligns with a short side, and continue along the length of the corner. Plywood/OSB Sheathing Water Proofing Outside Corner Piece 6
7 Installing Storage and Last Handling Course Installing Last Course Install KuraStone pieces in moderate contact with any soffit or ceiling (soffits or ceilings should be installed first). Cut pieces to fit top row height. Situation 1 Cut pieces are taller than the clip length (greater than 90mm/3.5 inches). Attach clips vertically (on the side grooves of the pieces at all the joints). Situation 2 Top row cut pieces are shorter than the length of the clip, but greater than the height of the starter. 2.4 inches < Cut Pieces < 3.5 inches Cut the starter track into 4-inch-wide strips. Attach these strips to the sheathing, using two (2) screws, at each vertical joint. Fit KuraStone pieces into the starter strip where they join. Situation 3 Cut piece is shorter than starter track. Cut Pieces Cut piece < 50 mm/2 a cut piece of Nichiha green shim (FS1005) behind each piece vertical joint, apply construction adhesive. Face fastening of piece may be required. Pre-drill holes when face fastening KuraStone pieces. 4 -wide Starter Pieces Situation 1 Cut Piece 4 -wide Starter Piece Situation 2 7
8 Door Storage & Window and Openings Handling& Trim Door & Window Openings & Trim Appropriate flashing and waterproofing tape should be used to prevent moisture penetration on all door and window openings. Refer to local building codes for best practices. Double-sided butyl tape is highly recommended at door and window flanges or around trim, prior to installing the WRB. Opening Top Install starter track over windows and install as specified in first panel course guidelines. Option: when starter track cannot be used, i.e. when piece above opening is cut, install an L- or J- channel with a 1/8 gap from the door or window trim to support pieces. Make sure channel is level before installing pieces. Opening Sides & Trim Install pieces to butt up to trim in moderate contact. Opening Bottom Install pieces to butt up to trim in moderate contact and follow the steps as described in Installing Last Course. Opening Top L-shaped Angle Shim (when installing) Window OSB Tape (Double-Sided) Window OSB Water Proofing Tape (Double-Sided) Opening Sides Window Tape (Double-Sided) OSB Opening Bottom Nichiha USA, Inc Peachtree Industrial Blvd. Suite AA, Norcross, GA Toll Free: 1.86 NICHIHA 1, (866) P. (770) F. (770) nichiha.com KURASTONE is a trademark of Nichiha USA, Inc Nichiha USA, Inc. All rights reserved. Printed in the USA KSI Silica Dust Warning: NICHIHA products may contain some amounts of crystalline silica [a.k.a. sand, silicon dioxide], which is a naturally occurring mineral. The amount will vary from product to product. Inhalation of crystalline silica into the lungs and repeated exposure to silica can cause health disorders, such as silicosis, lung cancer, or death depending upon various factors. To be conservative, Nichiha recommends that whenever cutting, sawing, sanding, sniping or abrading the product, users observe the Safety Instructions above. For further information or questions, please consult the MSDS, your employer, or visit html and The MSDS for Nichiha products are available at at your local Nichiha dealer or through Nichiha directly at FAILURE TO ADHERE TO OUR WARNINGS, MSDS, AND OTHER INSTRUCTION MAY LEAD TO SERIOUS PERSONAL INJURY OR DEATH. 8
ARCHITECTURAL WALL PANELS AUGUST KuraStone Installation Guide 1
ARCHITECTURAL WALL PANELS AUGUST 2018 KuraStone Installation Guide 1 NICHIHA ARCHITECTURAL WALL PANELS INSTALLATION GUIDE KURASTONE TM TABLE OF CONTENTS Basics 3 Kurastone Wall Pieces 3 Outside Corner
More informationINSTALLATION INSTRUCTIONS
CERBER FIBER CEMENT SIDING - SIERRA PREMIUM SHAKE Construction Requirements Sierra Premium Shake boards must be installed over vertical wood framing spaced no greater than 16 oc. with an APA rated 7/16
More informationNichiProducts Installation Guidelines
NichiProducts Installation Guidelines General Instructions for All NichiProducts Construction Requirements NichiProducts can be installed directly on braced wood or steel stud (20GA or heavier) construction
More informationINSTALLATION GUIDE SAVANNAH SMOOTH & SIERRA PREMIUM SHAKE
INSTALLATION GUIDE SAVANNAH SMOOTH & 1 NICHIHA INSTALLATION GUIDE FOR SAVANNAH SMOOTH & GENERAL INSTRUCTIONS FOR SAVANNAH SMOOTH & CONSTRUCTION REQUIREMENTS Savannah Smooth and Sierra Premium Shake boards
More informationCOMPOSITE SIDING INSTALLATION GUIDE
CENTURY HOME LIVING COMPOSITE SIDING INSTALLATION GUIDE Read all instructions prior to installing any siding product. Failure to install and finish this product in accordance with all local building codes,
More informationINSTALLATION GUIDE NICHIPRODUCTS & NICHIFRONTIER
INSTALLATION GUIDE NICHIPRODUCTS & NICHIFRONTIER 1 NICHIHA INSTALLATION GUIDE FOR NICHIPRODUCTS & NICHIFRONTIER INSTALLATION GUIDE NICHIPRODUCTS & NICHIFRONTIER 2 GENERAL INSTRUCTIONS FOR ALL NICHIPRODUCTS
More informationShapes Siding. Perfection Shingles. Chalk Line
Snap a Chalk Line Shapes Siding Perfection Shingles Chalk Line To establish a straight reference line to guide the positioning of the starter strip and the first course of siding, snap a chalk line. starter
More informationINSTALLATION GUIDE NICHIPRODUCTS
INSTALLATION GUIDE NICHIPRODUCTS 1 NICHIHA INSTALLATION GUIDE FOR NICHIPRODUCTS INSTALLATION GUIDE NICHIPRODUCTS TABLE OF CONTENTS General Instructions 3 Product Inspection 3 Storage & Handling 4 Minimum
More informationResysta 6 and 4 Flat Board Siding System Assembly Installation Guidelines
Resysta 6 and 4 Flat Board Siding System Assembly Installation Guidelines NOTE: Proper planning of the siding layout is essential for ease of installation of siding boards and siding components. Thoroughly
More informationInstallation Manual for Thermo Panel
Installation Manual for Thermo Panel 1 About Thermo Panel is a building wrap, insulation, air and water barrier, mold inhibitor and cold bridge eliminator all-in-one. Delivering an R-value of up to 5 on
More informationMAXISHINGLE LAP SIDING INSTALLATION GUIDE
MAXISHINGLE LAP SIDING INSTALLATION GUIDE Read all instructions prior to installing any siding product. Failure to install and finish this product in accordance with all local building codes, regulations
More informationMULTISHAKE LAP SIDING INSTALLATION GUIDE STORAGE AND HANDLING: PACKAGING:
MULTISHAKE LAP SIDING INSTALLATION GUIDE Read all instructions prior to installing any siding product. Failure to install and finish this product in accordance with all local building codes, regulations
More informationInstallation Guide - Evolution Series Wood Siding
Installation Guide - Evolution Series Wood Siding The following instructions pertain to the installation of Fraser Wood Siding Evolution Series on a typical wood frame construction allowing for nail penetration
More informationPRIMED STRAND REVERSIBLE SHAKE
PRIMED STRAND REVERSIBLE SHAKE PRIOR TO INSTALLATION Inspect product for any issues before installing (breakage, surface defects, foreign objects). Do not install questionable product. Report any problems
More informationRead guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
Installation Guide for E-Series/Eagle High-Performance Mullion Windows with LVL Reinforcement and Installed Using Type B Clips Thank you for choosing Andersen. Instructions are for typical, new wood-framed
More informationTruGrain 6 and 4 Flat Board Siding System Assembly Installation Guidelines
TruGrain 6 and 4 Flat Board Siding System Assembly Installation Guidelines NOTE: Proper planning of the siding layout is essential for ease of installation of siding boards and siding components. Thoroughly
More informationHardieTrim NT3 TM board is a decorative non-load bearing trim product. Figure 3. Fasten HardieTrim Flat Tab to minimum 7/16" OSB.
4/4 & 5/4 Boards with Back Grooves EFFECTIVE JULY 2011 INSTALLATION REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS Visit www.jameshardie.com for the most recent version. IMPORTANT: FAILURE TO INSTALL AND FINISH
More informationLAP SIDING INSTALLATION GUIDE
MaxiPLANK TM LAP SIDING INSTALLATION GUIDE and MAXITILE We suggest that you read these instructions at least twice. MaxiPLANK TM designs: Classic, Colonial and Provenzal. MaxiPLANK TM is 12 in length with
More informationlap siding Visit for the most recent version.
INSTALLATION REQUIREMENTS lap siding Visit www.artisanluxury.com for the most recent version. EFFECTIVE JAN 2011 IMPORTANT: FAILURE TO INSTALL AND FINISH THIS PRODUCT IN ACCORDANCE WITH APPLICABLE BUILDING
More information4/4, 5/4 Boards EFFECTIVE JULY 2011 INSTALLATION REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS
4/4, 5/4 Boards EFFECTIVE JULY 2011 INSTALLATION REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS STORAGE & HANDLING: Store flat and keep dry and covered prior to installation. Installing wet or saturated may
More informationInstallation Guide. for E-Series/Eagle Clad Hinged Inswing French Door
Installation Guide for E-Series/Eagle Clad Hinged Inswing French Door Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place.
More informationHow To Install Windows: Nail-Fin Application
How To Install Windows: Nail-Fin Application Required Tools & Materials: Materials: 1 3/4" galvanized roofing nails. Nails must penetrate at least 1" into framing For mulled and/or DP50 or above units:
More informationAdorn Mortarless Stone Veneer Installation Natural Concrete Products
Adorn Mortarless Stone Veneer Installation Adorn Mortarless Stone Veneer can be used on new or existing construction. Adorn is nailed or screwed onto the wall; therefore no brick ledge is required. Adorn
More informationNT3. Figure 3. Fasten HardieTrim Flat Tab to minimum 7/16" OSB with min 2, 6d
4/4 & 5/4 Boards with Back Grooves INSTALLATION REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS INSTALLATION OUTDOORS 1. Position cutting station so that wind will blow dust away from user and others in working
More informationInstallation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit.
Installation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit. Installer: Read these instructions completely before starting any installation.
More informationBoards. British Columbia
4/4 & 5/4 INSTALLATION REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS These instructions are to be used for HardieTrim HZ Boards ONLY and are ONLY valid in British Columbia. HardieTrim board is a decorative
More informationLAP SIDING INSTALLATION GUIDE
MAXIPANEL LAP SIDING INSTALLATION GUIDE Read all instructions prior to installing any siding product. Failure to install and finish this product in accordance with all local building codes, regulations
More informationHarvest (8094) Mystic (8078) Niagara (8095) Shenandoah (8057) 2 DURATA MORTARLESS STONE DURATA FLAT KIT PROFILE #:
INSTALLATION GUIDE DURATA FLAT KIT PROFILE #: 75524510 PACKAGE CONTENTS: 3 flat panels 6 transitions 3 bracket kits (6 brackets, 12 screws) COVERAGE PER KIT: 7.08 sq ft. DURATA CORNER KIT PROFILE #: 75526011
More informationINSTALLATION, STORAGE AND WALL CONSTRUCTION DETAILS
www.capecodsiding.com INSTALLATION, STORAGE AND WALL CONSTRUCTION DETAILS IMPORTANT READ THE FOLLOWING INSTRUCTIONS CAREFULLY BEFORE INSTALLING YOUR WOOD SIDING. FAILURE TO STRICTLY FOLLOW THESE INSTALLATION,
More informationSTACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS
STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions
More informationEffective February, 2015
Effective February, 2015 Table of Contents Ensuring System Performance 1 Components 2 Frequently Asked Questions 3 List of Tools 3 Before you Begin Preparation 3 Quality Tips 4 Cold Weather Tips 4 Cleaning
More informationLAP SIDING INSTALLATION GUIDE
MultiSHAKE TM LAP SIDING INSTALLATION GUIDE and MAXITILE We suggest that you read these instructions at least twice. MultiSHAKE TM spread and zero smoke generation. MultiSHAKE TM is available in Staggered
More informationBoards CUTTING INSTRUCTIONS STORAGE & HANDLING:
Boards EFFECTIVE APRIL 2018 These instructions are to be used for HZ Boards ONLY and are ONLY VALID in the following states: WA, OR, CA, NV, UT, ID, CO, WY, MT, AZ, NM. IMPORTANT: FAILURE TO FOLLOW JAMES
More informationInstallation Instructions Split Shake, Staggered Shake, Shingle, Perfection Shingle, and Shapes
Installation Instructions Split Shake, Staggered Shake, Shingle, Perfection Shingle, and Shapes General Guidelines These instructions show one type of installation and are intended for the professional
More informationAluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement
Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement 1 Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement The following instructions are a supplement
More informationFlashing Materials. Rough Opening Preparation
Installation Instructions for CertainTeed New Construction Windows Handling vinyl windows CAUTION: Always store vinyl windows and doors in an upright position on a slight angle. Never lay them flat or
More informationEagle clad double-hung window installation instructions
Eagle clad double-hung window installation instructions These instructions are for typical installation in new typical wood frame wall construction. These instructions and methods are not intended for
More informationInspire Aledora Slate Application Guidelines
July 2014 Inspire Aledora Slate Application Guidelines Only Basic Roofing Tools Required Hand fastened or fastened with a pneumatic nail gun Utility knife or a standard circular saw Tape measure, pry bar,
More informationROOFING APPLICATION STANDARD (RAS) No. 130 INSTALLATION CRITERIA FOR WOOD SHINGLES AND SHAKES APPLICATION
ROOFING APPLICATION STANDARD (RAS) No. 130 INSTALLATION CRITERIA FOR WOOD SHINGLES AND SHAKES APPLICATION 1. 2. 3. Scope 1.1 This application standard provides the minimum installation criteria for wood
More informationNEW HOME WARRANTY A REFERENCE GUIDE FOR TYPICAL WALL AND WINDOW DETAILS (RAINSCREEN SYSTEM) SHOWN AS FIBRE CEMENT CLADDING
NEW HOME WARRANTY A REFERENCE GUIDE FOR TYPICAL WALL AND WINDOW DETAILS (RAINSCREEN SYSTEM) SHOWN AS Reference Guide 0.1 GENERAL 0.1 Reference Guide 0.2 Index 0.3 Disclaimer & Limitations 0.4 General Notes
More informationTools required by installer: Materials required by installer:
Installation Guidelines For Quaker Window Products Vinyl product line (Single Hung, Double Hung, Sliding Window, Fixed Window, Casement, Awning, and Hopper) Installer: Read these instructions completely
More informationVinyl Windows Manufactured by VPI Quality Windows
Vinyl Windows Manufactured by VPI Quality Windows Part Number: 531&591 Installation 531 & 591 SERIES SLIDING AND HUNG WINDOW INSTALLATION INSTRUCTIONS Installation Instructions for Typical Construction.
More informationLP SmartSide Soffit ON SITE STORAGE PREPARATION. Application Instructions Vented and Non-Vented Smooth Finish or Cedar Texture. General Information
Application Instructions Vented and Non-Vented Smooth Finish or Cedar Texture A B A - Open / Closed (Page 5) B - Vented (Page 6) ON SITE STORAGE Store off the ground well supported, on a flat well-drained
More informationEffective April 1, 2013
Effective April 1, 2013 Table of Contents Ensuring System Performance 1 Components 2 Frequently Asked Questions 3 List of Tools 3 Before you Begin Preparation 3 Quality Tips 4 Cold Weather Tips 4 Cleaning
More informationInstallation Guide for E-Series/Eagle Clad Mechanically Fastened Windows
Guide for E-Series/Eagle Clad Mechanically Fastened Windows Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place. Instructions
More informationTECHNICAL GUIDE BEONSTONE PANELIZED STONE SIDING
TECHNICAL GUIDE BEONSTONE PANELIZED STONE SIDING TABLE OF CONTENTS This installation guide provides detailed step-by-step instructions for do-it-yourself projects. We invite you to read it carefully and
More informationInstallation Instructions for Standard Lap and Self-Aligning Lap Siding
Installation Instructions for Standard Lap and Self-Aligning Lap Siding 7/16 in. Standard Laps Include: All Old Mill Widths, Cedar Shake Lap and Smooth Lap 1/2 in. Self-Aligning Include: 8 in. and 12 in.
More informationChapter 17 - Porch Trim
Chapter 17 - Porch Trim Contents Chapter 17 - Porch Trim... 17-1 Timing & Prerequisites... 17-2 Trim on Porch Beams (Volunteer)... 17-4 Smart Trim on the Bottom of the Beam... 17-4 Smart Trim on the Inside
More informationapplication instructions
application instructions architectural collection cedar shake 76 series lap siding General At the time of manufacture, siding meets or exceeds the performance standards set forth in Composite Panel Association
More informationInstallation Guidelines. Next Dimension. Single Hung / Single Hung Fixed / Double Hung / Sliding Window / Fixed Window
Installation Guidelines Next Dimension Single Hung / Single Hung Fixed / Double Hung / Sliding Window / Fixed Window Windsor Windows & Doors Windsor Windows & Doors 900 S. 19 th St. 2210 Stafford St. Extn
More informationInstallation Instructions for Old Mill Shingle and Designer Shake Lap Siding
Installation Instructions for Old Mill Shingle and Designer Shake Lap Siding Includes: Cove, Craftsmen Staggered, Diamond, Fish Scale, Octagon, Round and Old Mill Shingle Lap Important: Read and understand
More informationfor Andersen 400 Series Woodwright Transom over 400 Series Woodwright Double-Hung or 400 Series Woodwright Picture Window
for Andersen 400 Series Woodwright Transom over 400 Series Woodwright Double-Hung or 400 Series Woodwright Picture Window Congratulations! You have just purchased one of the many fine Andersen products.
More informationSTRAIGHT EDGE, STAGGERED EDGE, HALF-ROUND PANELS AND INDIVIDUAL SHINGLES INSTALLATION REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS
Siding STRAIGHT EDGE, STAGGERED EDGE, HALF-ROUND PANELS AND INDIVIDUAL SHINGLES REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS EFFECTIVE APRIL 2009 Visit www.jameshardie.com for the most recent version. IMPORTANT:
More informationeco-shake INSTALLATION INSTRUCTION
1 eco-shake INSTALLATION INSTRUCTION NOTE: Shuffling the eco-shakes during installation may be necessary to obtain a uniform color throughout the roof. Due to the natural wood content in the ecoshakes,
More informationBest Barns USA. the Brookhaven 10' x 16' Assembly Book. revised March 23, 2016
Best Barns USA Assembly Book revised March 23, 2016 the Brookhaven 10' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationSECTION LAP SIDING. A. Fiber cement lap siding, panels, single, trim, fascia, moulding and accessories.
SECTION 07460 LAP SIDING PART 1 GENERAL 1.1 SECTION INCLUDES A. Fiber cement lap siding, panels, single, trim, fascia, moulding and accessories. B. Factory-finished fiber cement lap siding, panels, single,
More informationHardieShingle Siding Product Description
HardieShingle Siding Product Description HardieShingle siding is fiber-cement shingle siding for sidewall applications. HardieShingle siding is available as straight-edge panels or staggered-edge panels
More informationTurada Hardwood Shingles and Shakes Installation instructions
1. General 1.1 Maximum Exposure: Maximum exposure for wood shingles and shakes shall comply with Table 1 herein, unless specifically specified in the roof assemblies Product Approval. 1.2 Solid and Spaced
More informationCERACLAD.
CERACLAD 4. Horizontal Application (Wood Structure) Instructions and Details Siding Panel Installation Accessories Installation Overview Starter Bar Installation Install s Installation
More informationSiding STRAIGHT EDGE, STAGGERED EDGE, HALF-ROUND PANELS & INDIVIDUAL SHINGLES INSTALLATION REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS
Siding STRAIGHT EDGE, STAGGERED EDGE, HALF-ROUND PANELS & INDIVIDUAL SHINGLES INSTALLATION REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS EFFECTIVE SEPTEMBER 1 Visit www.jameshardie.com for the most recent
More informationInspire Slate Starter Piece Hip and Ridge. 13 1/2" Height: 13 ½" Width: 12" Squares/ Pallet. Bundles/ Square
December 2017 Classic Slate Application Guidelines Only Basic Roofing Tools Required Hand fastened or fastened with a pneumatic nail gun Utility knife or a standard circular saw Tape measure, pry bar,
More informationInstall Windsor Corners
Install Windsor Corners Tools and Supplies You'll Need 1. Exterior Grade Screws use screws that are long enough to go through the FauxPanel and firmly attach to the wall behind the FauxPanel. We recommend
More informationTYPAR WEATHER PROTECTION SYSTEM TABLE OF CONTENTS. SPECIAL INSTALLATION CONSIDERATIONS Stucco** Brick** Stone Veneer** Wood Siding**
TYPAR WEATHER PROTECTION SYSTEM INSTALLATION GUIDE TABLE OF CONTENTS Table of Contents...01 Special Installation Considerations...01 Code Requirements...02 Approvals and Reports...02 Recommended Materials...02
More informationInstallation Instructions
Installation Instructions SLICKER CLASSIC RAINSCREEN Page List of Approved Compatible Products 2 Nail Selection Guide 3 General Installation 4 Insulation Board Installation 5 EIFS Installation 6 Top of
More informationINSTALLATION INSTRUCTIONS for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) ImpOrTaNT INFOrmaTION & GlOssary.
for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) Thank you for selecting JELD -WEN products. Attached are JELD-WEN s recommended installation instructions for metal clad wood windows
More informationINSTALLATION INSTRUCTIONS for Wood Bay or Bow Windows with Nailing Fin or Exterior Trim (JII032)
for Wood Bay or Bow Windows with Nailing Fin or Exterior Trim (JII0) Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for wood and clad wood bay
More informationSiding STRAIGHT EDGE, STAGGERED EDGE, HALF ROUNDS & INDIVIDUAL SHINGLES INSTALLATION REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS
Siding STRAIGHT EDGE, STAGGERED EDGE, HALF ROUNDS & INDIVIDUAL SHINGLES INSTALLATION REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS EFFECTIVE SEPTEMBER 201 Visit www.jameshardie.com for the most recent version.
More informationSiding STRAIGHT EDGE, STAGGERED EDGE, HALF-ROUND PANELS & INDIVIDUAL SHINGLES INSTALLATION REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS
NEW Siding STRAIGHT EDGE, STAGGERED EDGE, HALF-ROUND PANELS & INDIVIDUAL SHINGLES INSTALLATION REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS EFFECTIVE JANUARY 2011 Visit www.jameshardie.com for the most recent
More informationInstallation Guide Classic Series Wood Siding
Installation Guide Classic Series Wood Siding Please read the following instructions prior to beginning your installation. The following installation guidelines have been produced in accordance with the
More informationROOFING APPLICATION STANDARD (RAS) No. 130
ROOFING APPLICATION STANDARD (RAS) No. 130 1. Scope 1.1 This application Standard provides the minimum installation criteria for wood shingles and shakes. 2. Definitions 2.1 For definitions of terms used
More informationInstallation Guide. Shingles. Classical. Shingles. Warning. Storage. Cutting Shingles. Touch-Up. Eastern White Cedar
Installation Guide Before you begin, take the time to read this entire guide to clearly understand the requirements and steps to follow for proper installation. The Fastening Make shingle fastening simpler
More informationVinyl Windows and Doors Manufactured by VPI Quality Windows
Vinyl Windows and Doors Manufactured by VPI Quality Windows Part Number: 511_Installation ENDURANCE CASEMENT\AWNING\PW INSTALLATION INSTRUCTIONS Installation Instructions for Typical Construction These
More informationIntegrity Polygon and Round Top Installation and Finishing Instructions
Integrity Polygon and Round Top Installation and Finishing Instructions 08/20/2004 70852 BEFORE YOU BEGIN IMPORTANT: Read these instructions thoroughly before beginning to install your Integrity Polygon
More information4. Metal roof jacks at penetrations and attachments
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - SECTION 07 61 00 METAL SHINGLE ROOFING - - - - - - - - - - -
More informationHardieTrim Boards Products Description
Product Information Boards Products Description boards come finished with either the PrimePlus factory primer and sealer or with ColorPlus Technology. The ColorPlus coating is a factory-applied, oven-baked
More informationSiding. HardieShingle CUTTING INSTRUCTIONS STORAGE & HANDLING:
HardieShingle Siding SINGLE FAMILY INSTALLATION REQUIREMENTS EFFECTIVE APRIL 18 IMPORTANT: FAILURE TO FOLLOW JAMES HARDIE WRITTEN INSTALLATION INSTRUCTIONS AND COMPLY WITH APPLICABLE BUILDING CODES MAY
More informationHardieTrim Boards Products Description
Working Safely Tools for Cutting and Fastening Installation Finishing and Maintenance Boards Products Description boards come finished with either the PrimePlus factory primer and sealer or with ColorPlus
More informationC e r t a i nte e d. FiberCement Siding
C e r t a i nte e d FiberCement Siding Installation Manual TABLE OF CONTENTS Section 1: Before you begin...1 Section 2: Safety...2 Section 3: Storage and Handling...3 Section 4: Tools and Accessory Items...4
More information(773) INSTALLATION INSTRUCTIONS for Vinyl Windows with Integral Nailing Fin (JII001) IMPORTANT INFORMATION & GL OSSARY ROUGH OPENINGS
Thank you for selecting C l i m a t e G u a r d products. Attached are our recommended installation instructions for Vinyl windows with an integral (2400-02) will not affect application of the ClimateGuard
More informationTape Measure Metal Clippers Screw Bit Set With Extensions
IMPORTANT: Read through instructions thoroughly before beginning to replace any damaged material. Minor damage can be fixed with a fiberglass repair kit and color matched paint. Tools Required Tape Measure
More informationINSTALLATION INSTRUCTIONS for Vinyl Projecting Windows with Integral Nailing Fin (JII023)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for vinyl bay, bow and garden windows which incorporate an integral nailing fin. While the use of
More informationFold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE
Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE This instruction guide provides the minimum recommended procedures to correctly prepare the rough opening, install a fold-a-way patio door unit and apply
More informationFlorida Product Approval HardiePlank Lap Siding
Florida Product Approval HardiePlank Lap Siding For use inside HVHZ: o HardiePlank Lap Siding fastener types, fastening schedule, and installation shall be in accordance with the Miami-Dade County Florida
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised September 12, 2017 the Denver 12' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted. Under the
More informationSteel Reinforced Joining Thank you for choosing Andersen. Please leave this guide with building owner.
Steel Reinforced Joining (Horizontal/Vertical) for Andersen 400 Series Woodwright & Tilt-Wash Double-Hung, Picture, and Transom Windows and 400 Series Double-Hung Half Circle and Flexiframe Specialty Windows
More informationHardieShingle Siding Product Description
Working Safely Tools for Cutting and Fastening HardieShingle Siding Product Description HardieShingle siding is fiber-cement shingle siding for sidewall applications. HardieShingle siding is available
More informationINSTALLATION INSTRUCTIONS for Wood Bay or Bow Windows with Nailing Fin or Exterior Trim (JII032) IMPORTANT INFORMATION AND GLOSSARY ROUGH OPENINGS
for Wood Bay or Bow Windows with Nailing Fin or Exterior Trim (JII0) Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for wood and clad wood bay
More informationInstallation Guidelines
Installation Guidelines Tando Building Products provides these instructions as general guidelines only. Tando Building Products neither installs exterior cladding nor has any control over any installation.
More informationINSTALLATION INSTRUCTIONS for Vinyl Windows with Integral Nailing Fin (JII001) IMPORTANT INFORMATION & GLOSSARY ROUGH OPENINGS
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for Vinyl windows with an integral nailing fin. While the use of these installation instructions
More informationBest Materials LLC distributes backer rod, caulking and sealants for all types of EIFS joints and penetration sealing applications.
Best Materials LLC distributes backer rod, caulking and sealants for all types of EIFS joints and penetration sealing applications. EXTERIOR INSULATION & FINISH SYSTEM CONSTRUCTION Data Published Courtesy
More informationDura-Lock Roof System
DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.
More informationSteel Reinforced Joining Guide (Horizontal / Vertical)
(Horizontal / Vertical) for Andersen Patio Door and/or Elliptical Top Window Combinations Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation
More informationHardieTrim Boards Products Description
Working Safely Tools for Cutting and Fastening Installation Product Information Finishing and Maintenance HardieWrap Weather Barrier Boards Products Description HARDIETRIM 5/4 BOARDS 5/4 boards is a decorative
More informationBest Barns USA. Assembly Book. 12'x 16' the Millcreek. Revised September 19, 2017
Assembly Book Best Barns USA Revised September 19, 2017 the Millcreek 12'x 16' Manufactured by Reynolds Building Systems, Inc 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted Under the
More informationHardieTrim Boards Products Description
Working Safely Tools for Cutting and Fastening Installation Finishing and Maintenance HardieWrap Weather Barrier Product Information Boards Products Description HARDIETRIM 5/4 BOARDS 5/4 boards is a decorative
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised September 19, 2017 the Millcreek 12'x 20' Manufactured by Reynolds Building Systems, Inc 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted Under the
More informationSun Windows General Information New Construction Hinged Door Installation Instructions
A G H F H H A. Apply Weather Resistive Barrier B. Apply Bottom Flashing Tape C. Install Sill Pan End Caps & Pan D. Caulk Sides & Top Nailing Surface, Set Door, Fasten E. Apply Side Flashing Tape F. Apply
More informationROOFING APPLICATION STANDARD (RAS) No. 115 STANDARD PROCEDURES FOR ASPHALTIC SHINGLE INSTALLATION
ROOFING APPLICATION STANDARD (RAS) No. 115 STANDARD PROCEDURES FOR ASPHALTIC SHINGLE INSTALLATION 1. Scope 4. Underlayment 2. 1.1 This roofing application standard has been developed to provide a responsive
More informationSTRAIGHT EDGE, STAGGERED EDGE NOTCHED, HALF-ROUND PANELS & INDIVIDUAL SHINGLES INSTALLATION REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS
Siding STRAIGHT EDGE, STAGGERED EDGE NOTCHED, HALF-ROUND PANELS & INDIVIDUAL SHINGLES INSTALLATION REQUIREMENTS - PRIMED & COLORPLUS PRODUCTS EFFECTIVE APRIL 2009 Visit www.jameshardie.com for the most
More informationROOFING APPLICATION STANDARD (RAS) No. 115 STANDARD PROCEDURES FOR ASPHALTIC SHINGLE INSTALLATION
ROOFING APPLICATION STANDARD (RAS) No. 115 STANDARD PROCEDURES FOR ASPHALTIC SHINGLE INSTALLATION 1. Scope 4. Underlayment 2. 1.1 This roofing application standard has been developed to provide a responsive
More information