SECTION WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS

Size: px
Start display at page:

Download "SECTION WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS"

Transcription

1 SECTION WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Architectural wood cabinets (kitchenette and pantry) 2. Laminate Countertops. 3. Cabinet hardware. 4. Wood furring, blocking, shims, and hanging strips for installing architectural wood cabinets unless concealed within other construction before cabinet installation. 5. Shop finishing of architectural wood cabinets. 6. Metal access panel to be installed in upper cabinet. 1.3 PREINSTALLATION MEETINGS A. Pre-installation Conference: Conduct conference at Project site. 1. Review methods and procedures related to wood architectural cabinets including, but not limited to, the following: a. Review delivery, storage, and handling procedures. b. Review ambient condition and ventilation procedures. c. Review Phasing Schedule for installation. 1.4 ACTION SUBMITTALS A. Product Data: For each type of product. B. Product Data for metal access panel to be installed in upper cabinet. Refer to the plumbing drawings. C. Shop Drawings: Show location of each item, dimensioned plans and elevations, large-scale details, attachment devices, and other components. 1. Show details full size. 2. Show locations and sizes of furring, blocking, and hanging strips, including concealed blocking and reinforcement specified in other Sections. 3. Show locations and sizes of cutouts and holes for electrical switches and outlets installed in architectural wood cabinets. 4. Show locations and sizes of cutouts required for access panel in upper cabinet. WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS

2 5. Show full details of counters, including locations and sizes of cutouts and holes for plumbing fixtures, faucets and other items to be installed in the plastic-laminate countertop. D. Samples for Verification: 1. Submit full sized raised panel door, illustrating final cabinet finish. 2. Submit two 5 by 8 inch size samples, illustrating countertop material. a. PL 1 - Kitchenette b. PL2- Office 213 Counter 3. Submit two samples of drawer and door pulls and hinges illustrating hardware finish. 4. Submit Two 6 inch long samples, illustrating upper cabinets crown molding. 1.5 INFORMATIONAL SUBMITTAL A. Qualification Data for custom cabinet manufacturer. 1.6 QUALITY ASSURANCE A. Fabricator Qualifications: Shop that employs skilled workers who custom fabricate products similar to those required for this Project and whose products have a record of successful inservice performance. B. Installer Qualifications: Fabricator must have 10 years of experience and a certified participant in AWl's Quality Certification Program. 1.7 DELIVERY, STORAGE, AND HANDLING A. Do not deliver cabinets until painting and similar operations that could damage woodwork have been completed in installation areas. If cabinets must be stored in a location other than installation areas, store only in areas where environmental conditions comply with requirements specified in "Field Conditions" Article. 1.8 FIELD CONDITIONS A. Environmental Limitations: Do not deliver or install cabinets until buildings or storage location is maintaining temperature between 60 and 90 deg F (16 and 32 deg C) and relative humidity between 25 to 55 percent during the remainder of the construction period. B. Field Measurements: Where cabinets are indicated to fit to other construction, verify dimensions of other construction by field measurements before fabrication, and indicate measurements on Shop Drawings. Coordinate fabrication schedule with construction progress to avoid delaying the Work. 1. Locate concealed framing, blocking, and reinforcements that support cabinets by field measurements before being enclosed, and indicate measurements on Shop Drawings. WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS

3 C. Established Dimensions: Where cabinets are indicated to fit to other construction, establish dimensions for areas where cabinets are to fit. Provide allowance for trimming at site, and coordinate construction to ensure that actual dimensions correspond to established dimensions. 1.9 COORDINATION A. Coordinate sizes and locations of framing, blocking, furring, reinforcements, and other related units of Work specified in other Sections to ensure that solid wood architectural cabinets with solid wood raised panel doors can be supported and installed as indicated. PART 2 PRODUCTS 2.1 ARCHITECTURAL CABINET FABRICATORS A. Source Limitations: Engage a qualified woodworking firm to assume undivided responsibility for production of architectural wood cabinets with sequence-matched wood side paneling. B. Quality Standard: Unless otherwise indicated, comply with the "Architectural Woodwork Standards" for grades of architectural wood cabinets indicated for construction, finishes, installation, and other requirements. 1. Provide certificate from AWl certification program indicating that woodwork complies with requirements of grades specified. 2. Provide cabinets that comply with KCMA A WOOD CABINETS FOR OPAQUE FINISH A. B. c. D. E. F. G. H. Grade: Premium. Type of Construction: Face Frame. Face Style: Reveal Overlay; Door and Drawer Faces Partially Cover Cabinet Fronts. Door and Drawer Fronts: Solid-wood stiles and rails, 3/4" thick, with 3/4" thick solid-wood center panels. Reveal Dimension: ~ inch. Face Frames: 3/4" by 1 5/8" solid wood with glued mortise and tenon or doweled joints. Exposed Cabinet End Finish: Decorative end panels to match the raised panel doors. Back, top and bottom rails: 3/4" by 2 %" solid wood, interlocking with end panels and rabbeted to receive top and bottom panels. Back rails secured under pressure with blue and mechanical fasteners. I. Wall Hung Back Panels: 3/16" thick plywood fastened to rear edge of end panels and to top and bottom rails. WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS

4 J. Base Unit Back Panels: 3/16" thick plywood fastened to rear edge of end panels and to top and bottom rails. K. Front Frame Drawer Rails: 3/4" by 1 1/4" solid wood mortised and fastened into face frame. L. Panel Product for Exposed Surfaces: Solid wood. M. Semi-exposed Surfaces: Provide surface materials indicated below: 1. Surfaces Other Than Drawer Bodies: Match materials indicated for exposed surfaces. 2. Edges of Medium-density fiberboard finished with thermally fused, melamineimpregnated Shelves: PVC or polyester edge banding. 3. Drawer Sides and Backs: Solid-hardwood lumber. 4. Drawer Bottoms: Medium-density fiberboard finished with thermally fused, melamineimpregnated. N. Drawer Construction: Fabricate with exposed fronts fastened to subfront with mounting screws from interior of body. 1. Join sub-fronts, backs, and sides with glued dovetail joints. 0. Shop Finishing: Finish cabinets in shop. Defer only final touchup until after installation. P. Color: Paint cabinets same white color as surrounding historic trim. 2.3 WOOD MATERIALS A. Wood Products: Provide materials that comply with requirements of referenced quality standard for each type of woodwork and quality grade specified unless otherwise indicated. 1. Do not use plain-sawn softwood lumber with exposed, flat surfaces. 2. Hardwood Moisture Content: kiln dried to 7 percent moisture content. 3. Do not use products that contain urea formaldehyde. B. Composite Wood and Agrifiber Products: Provide materials that comply with requirements of referenced quality standard for each type of woodwork and quality grade specified unless otherwise indicated. 1. Medium-Density Fiberboard: ANSI A208.2, Grade 130, made with binder containing no urea formaldehyde. 2. Medium-density fiberboard finished with thermally fused, melamine-impregnated paper and complying with requirements of NEMA LD 3, Grade VGL, for test methods 3.3, 3.4, 3.6, 3.8, and C. Exposed Wood Species: Maple, Alder, Birch or equal standard, paint grade hardwood. 1. Select materials for compatible color and grain. Do not use two adjacent exposed surfaces that are noticeably dissimilar in color, grain, figure, or natural character markings. D. Solid Wood: Clear hardwood lumber of species indicated, free of defects. WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS

5 E. Wood Crown Molding: Provide same solid wood material of cabinets. 2.4 CABINET HARDWARE AND ACCESSORIES A. B. C. D. E. F. General: Provide cabinet hardware and accessory materials associated with architectural cabinets. Frameless Concealed Hinges (European Type): BHMAA156.9, B01602, 100 degrees of opening, self-closing. Back-Mounted Pulls: BHMA A 156.9, B Adjustable Shelf Standards and Supports: BHMA A 156.9, B04071; with shelf rests, B Shelf Rests: BHMA A 156.9, B04013; two-pin type with shelf hold-down clip. Drawer Slides: BHMA A Grade 1 and Grade 2: Side mounted and extending under bottom edge of drawer; fullextension type; zinc-plated steel with polymer rollers. 2. For drawers not more than 3 inches high and not more than 24 inches wide, provide Grade For drawers more than 3 inches high but not more than 6 inches high and not more than 24 inches wide, provide Grade 1. G. Door and Drawer Silencers: BHMA A , L H. Exposed Hardware and Finishes: For exposed hardware, provide finish that complies with BHMA A for BHMA finish number indicated. 1. Dark, Satin Bronze,: BHMA 613 for brass base; BHMA 640 for steel base: 2. Basis of Design, as manufactured by Amerock, or Equal. a. Knob: SKU# BP24234RB b. Pull: SKU# BP55422RB I. For concealed hardware, provide manufacturer's standard finish that complies with product class requirements in BHMA A PLASTIC LAMINATE A. Plastic Laminate: Solid colored, textured, high pressure decorative laminate (HPDL), general purpose grade: NEMA LD 3, Grade HGS. 1. Subject to compliance with requirements, provide products by the following: a. Abet Laminati, Inc. b. Formica Corporation c. Wilsonart International d. Or Equal WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS

6 B. Colors: Provide materials and products that result in colors and textures of exposed laminate surfaces complying with the following requirements: 1. As selected by Architect from manufacturer's full range in the following categories: a. Solid Colors, matte finish. b. Patterns, matte finish c. Solid Colors with core same color as surface, matte finish. 2. Edge Treatment: Same as laminate cladding on horizontal sufraces. 3. Core Material: Particleboard or medium-density fiberboard. 4. Core Material at Sinks: Particleboard made with exterior glue. 5. Core Thickness: 3/4" a. Build up countertop thickness to 1 %" thick at front, back and ends with additional layers of core material laminated top. 6. Adhesive Bonding Plastic Laminate: Unpigmented contact cement, contact cement or Resorcinol. C. Fabrication 1. Fabricate countertops to dimensions, profiles, and details indicated. Provide front and end overland of 1 inch over base cabinets. 2. Complete fabrication, including assembly, to maximum extent possible before shipment. Disassemble components only as necessary for shipment and installation. Where necessary for fitting at site, provide ample allowance for scribing, trimming and fitting. 3. Trial fit assemblies at fabrication shop that cannot be shipped completely assembled. Install dowels, screws, bolted connectors, and other fastening devices that can be removed after trial fitting. Verify that various parts fit as intended and check measurements of assemblies against field measurements before disassembling for shipment. 2.6 MISCELLANEOUS MATERIALS A. Furring, Blocking, Shims, and Hanging Strips: Hardwood lumber, kiln dried to less than 15 percent moisture content. B. Anchors: Select material, type, size, and finish required for each substrate for secure anchorage. Provide metal expansion sleeves or expansion bolts for post-installed anchors. Use nonferrous-metal or hot-dip galvanized anchors and inserts at inside face of exterior walls and at floors. 2.7 FABRICATION A. Fabricate woodwork to dimensions, profiles, and details indicated. Ease edges to radius indicated for the following: 1. Corners of Cabinets: 1/16 inch unless otherwise indicated. B. Complete fabrication, including assembly, finishing, and hardware application, to maximum extent possible before shipment to Project site. Disassemble components only as necessary for shipment and installation. Where necessary for fitting at site, provide ample allowance for scribing, trimming, and fitting. WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS

7 1. Trial fit assemblies at fabrication shop that cannot be shipped completely assembled. Install dowels, screws, bolted connectors, and other fastening devices that can be removed after trial fitting. Verify that various parts fit as intended and check measurements of assemblies against field measurements before disassembling for shipment. C. Shop-cut openings to maximum extent possible to receive hardware, appliances, electrical work, and similar items. Locate openings accurately and use templates or roughing-in diagrams to produce accurately sized and shaped openings. Sand edges of cutouts to remove splinters and burrs. 2.8 SHOP FINISHING A. General: Finish architectural wood cabinets at fabrication shop as specified in this Section. Defer only final touchup, cleaning, and polishing until after installation. B. General: Drawings indicate items that are required to be shop finished. Finish such items at fabrication shop as specified in this Section. C. Finish Materials: Use finish materials that meet the testing and product requirements of the California Department of Health Services' "Standard Practice for the Testing of Volatile Organic Emissions from Various Sources Using Small-Scale Environmental Chambers." D. Shop Priming: Shop apply the prime coat including back priming, if any, for items specified to be field finished. E. Preparation for Finishing: Comply with referenced quality standard for sanding, filling countersunk fasteners, sealing concealed surfaces, and similar preparations for finishing architectural wood cabinets, as applicable to each unit of work. 1. Back priming: Apply one coat of sealer or primer, compatible with finish coats, to concealed surfaces of cabinets. F. Opaque Finish: 1. Grade: Premium. 2. Finish: System- 4, water-based latex acrylic. 3. Color: As selected by Architect from manufacturer's full range. 4. Sheen: Satin, gloss units measured on 60-degree gloss meter per ASTM D 523. PART 3 EXECUTION 3.1 PREPARATION A. Before installation, condition cabinets to average prevailing humidity conditions in installation areas. B. Before installing cabinets, examine shop-fabricated work for completion and complete work as required, including removal of packing and back priming. WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS

8 3.2 INSTALLATION A. B. c. D. E. Grade: Install cabinets to comply with same grade as item to be installed. Assemble cabinets and complete fabrication at Project site to the extent that it was not completed in the shop. Install cabinets level, plumb, true, and straight. Shim as required with concealed shims. Install level and plumb to a tolerance of 1/8 inch in 96 inches. Scribe and cut cabinets to fit adjoining work, refinish cut surfaces, and repair damaged finish at cuts. Anchor cabinets to anchors or blocking built in or directly attached to substrates. Secure with countersunk, concealed fasteners and blind nailing. Use fine finishing nails for exposed fastening, countersunk and filled flush with woodwork. 1. For shop finished items use filler matching finish of items being installed. F. Cabinets: Install without distortion so doors and drawers fit openings properly and are accurately aligned. Adjust hardware to center doors and drawers in openings and to provide unencumbered operation. Complete installation of hardware and accessory items as indicated. 1. Install cabinets with no more than 1/8 inch in 96-inch sag, bow, or other variation from a straight line. G. Touch up finishing work specified in this Section after installation of woodwork. Fill nail holes with matching filler where exposed. 1. Apply specified finish coats, including stains and paste fillers if any, to exposed surfaces where only sealer/prime coats are applied in shop. H. Counters: 1. Field Jointing is not permitted. 2. Install countertops level, plumb, true and straight. Shim as required with concealed shims. Install level and plumb to a tolerance of 1/8 inch in 96 inches. 3. Scribe and cut countertops to fit adjoining work, refinish cut surfaces, and repair damaged finish at cuts. 4. Anchor securely by screwing through corner blocks of base cabinets or other supports into underside of countertop. 5. Install with no sag, bow or other variation from a straight line. 6. Secure backsplashes to walls with adhesive 7. Seal junctures of tops, splashes, and walls with mildew-resistant silicone sealant or another permanently elastic sealing compound recommended by countertop material manufacturer. 3.3 ADJUSTING AND CLEANING A. Repair damaged and defective cabinets, where possible, to eliminate functional and visual defects; where not possible to repair, replace woodwork. Adjust joinery for uniform appearance. B. Clean, lubricate, and adjust hardware. WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS

9 C. Clean cabinets and countertops on exposed and semi-exposed surfaces. Touch up shopapplied finishes to restore damaged or soiled areas. END OF SECTION WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS

10

SECTION WOOD ARCHITECTURAL CABINETS AND QUARTZ COUNTERTOPS

SECTION WOOD ARCHITECTURAL CABINETS AND QUARTZ COUNTERTOPS SECTION 064113- WOOD ARCHITECTURAL CABINETS AND QUARTZ COUNTERTOPS PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions

More information

ADDENDUM TO THE CONTRACT. for the GLACIER FIRE STATION KITCHEN AND CLASSROOM RENOVATION. Contract No. E16-181

ADDENDUM TO THE CONTRACT. for the GLACIER FIRE STATION KITCHEN AND CLASSROOM RENOVATION. Contract No. E16-181 ADDENDUM TO THE CONTRACT for the ENGINEERING DEPARTMENT GLACIER FIRE STATION KITCHEN AND CLASSROOM RENOVATION Contract No. E6-8 ADDENDUM NO.: ONE CURRENT DEADLINE FOR BIDS: May 9, 206 PREVIOUS ADDENDA:

More information

DIVISON 6 WOODS AND PLASTICS SECTION PLASTIC LAMINATE FACED ARCHITECTUAL CABINETS

DIVISON 6 WOODS AND PLASTICS SECTION PLASTIC LAMINATE FACED ARCHITECTUAL CABINETS DIVISON 6 WOODS AND PLASTICS PART 1 - GENERAL 1:1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

D. Product Certificates: Signed by manufacturers of casework certifying that products furnished comply with requirements.

D. Product Certificates: Signed by manufacturers of casework certifying that products furnished comply with requirements. SECTION 12356 - CASEWORK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,

More information

A. Product Data: For each type of product indicated cabinet hardware and accessories, and finishing materials and processes.

A. Product Data: For each type of product indicated cabinet hardware and accessories, and finishing materials and processes. SECTION 06402 - INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1

More information

SECTION PLASTIC-LAMINATE-FACED ARCHITECTURAL CABINETS

SECTION PLASTIC-LAMINATE-FACED ARCHITECTURAL CABINETS SECTION 064116 - PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Plastic-laminate-faced architectural cabinets. 2. Wood furring, blocking, shims, and hanging strips for installing plastic-laminatefaced

More information

SECTION PLASTIC-LAMINATE-FACED ARCHITECTURAL CABINETS AND COUNTERTOPS

SECTION PLASTIC-LAMINATE-FACED ARCHITECTURAL CABINETS AND COUNTERTOPS SECTION 06 41 16 - CABINETS AND COUNTERTOPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

1. Division 6 Section "Rough Carpentry" for furring, blocking, and other carpentry work that is not exposed to view.

1. Division 6 Section Rough Carpentry for furring, blocking, and other carpentry work that is not exposed to view. SECTION 06402 INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification

More information

SECTION ARCHITECTURAL WOOD CASEWORK

SECTION ARCHITECTURAL WOOD CASEWORK SECTION 06410 - ARCHITECTURAL WOOD CASEWORK PART 1 GENERAL 1.01 SECTION INCLUDES A. Wood cabinets for opaque finish. B. Flush wood paneling for transparent finish. C. Factory finishing. 1.02 RELATED REQUIREMENTS

More information

SECTION ARCHITECTURAL WOODWORK

SECTION ARCHITECTURAL WOODWORK SECTION 06400 ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Custom Cabinet Units a. Plastic Laminate b. Sound Barrier for Casework 2. Cabinet Hardware B. Related Sections:

More information

ADDENDUM TO BID DOCUMENTS ADDENDUM #03 SCCD RFP: # Project: Solano Community College District Vacaville Classroom Building (Annex) Renovation

ADDENDUM TO BID DOCUMENTS ADDENDUM #03 SCCD RFP: # Project: Solano Community College District Vacaville Classroom Building (Annex) Renovation Vacaville Classroom Annex Renovation Documents #18-005 ADDENDUM TO BID DOCUMENTS ADDENDUM #03 SCCD RFP: #18 005 Project: Vacaville Classroom Building (Annex) Renovation Date: 11/22/2017 Addendum # 03 The

More information

Student Services & Classroom Addition

Student Services & Classroom Addition SECTION 105116 - WOOD LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,

More information

SECTION INTERIOR ARCHITECTURAL WOODWORK

SECTION INTERIOR ARCHITECTURAL WOODWORK SECTION 064023 INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Plastic-laminate cabinets. 2. Plastic-laminate countertops. 3. Plastic-laminate window sills. 4. Cabinet

More information

B. Shop Drawings: For residential casework. Include plans. elevations, details, and attachments to other work.

B. Shop Drawings: For residential casework. Include plans. elevations, details, and attachments to other work. HVAC 1Sunporch 1Fire Alarm Renovation SECTION 123530 RESIDENTIAL CASEWORK PART 1 - GENERAL 1.1 SUMMARY A. Section includes laundry room cabinets. 1.2 ACTION SUBMITTALS A. Product Data: For each type of

More information

Lindenwold Boro Hall Lindenwold, NJ. Bishop & Smith Architects Laurel Springs, NJ. August 2, 2012 PART 1 - GENERAL 1.1 SUMMARY. A.

Lindenwold Boro Hall Lindenwold, NJ. Bishop & Smith Architects Laurel Springs, NJ. August 2, 2012 PART 1 - GENERAL 1.1 SUMMARY. A. SECTION 061000 - ROUGH CARPENTRY PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Wood blocking and nailers. 2. Wood furring and grounds. 3. Plywood backing panels. 1.2 ACTION SUBMITTALS A. Product

More information

WHITE W/OAK TRIM NATURAL MEDIUM NORTHPORT OAK

WHITE W/OAK TRIM NATURAL MEDIUM NORTHPORT OAK WHITE W/OAK TRIM NATURAL MEDIUM NORTHPORT OAK Accessories. We believe that functionality is at the heart of any great kitchen. Above are a few of the accessories available with Merillat Essentials. The

More information

SECTION INTERIOR ARCHITECTURAL WOODWORK

SECTION INTERIOR ARCHITECTURAL WOODWORK SECTION 06402 - INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1

More information

A. Dimension Lumber: Lumber of 2 inches nominal or greater but less than 5 inches nominal in least dimension.

A. Dimension Lumber: Lumber of 2 inches nominal or greater but less than 5 inches nominal in least dimension. SECTION 06 10 53 - MISCELLANEOUS ROUGH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

SECTION MANUFACTURED CASEWORK

SECTION MANUFACTURED CASEWORK 1 GENERAL 1.1 SECTION INCLUDES SECTION 12300 MANUFACTURED CASEWORK A. Work required to complete the manufactured casework indicated by the Contract Documents, and the items necessary for its proper installation.

More information

SECTION INTERIOR ARCHITECTURAL WOODWORK

SECTION INTERIOR ARCHITECTURAL WOODWORK SECTION 06 40 23 INTERIOR ARCHITECTURAL WOODWORK PART 1 GENERAL 1.01 SECTION INCLUDES A. Laminate clad cabinets and custom components. B. Laminate clad countertops. C. Cabinet hardware including countertop

More information

SECTION MISCELLANEOUS ROUGH CARPENTRY

SECTION MISCELLANEOUS ROUGH CARPENTRY SECTION 06 1053 - MISCELLANEOUS ROUGH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

SECTION FINISH CARPENTRY PART 1 GENERAL. 1.1 SECTION INCLUDES A. Interior Finish Carpentry Work: 1. Refer to schedule at end of Section.

SECTION FINISH CARPENTRY PART 1 GENERAL. 1.1 SECTION INCLUDES A. Interior Finish Carpentry Work: 1. Refer to schedule at end of Section. SECTION 06200 - FINISH CARPENTRY PART 1 GENERAL 1.1 SECTION INCLUDES A. Interior Finish Carpentry Work: 1. Refer to schedule at end of Section. 1.2 RELATED SECTIONS A. Section 06100 - Rough Carpentry:

More information

OCCE Courtroom Built-in SSA Jacksonville, NC

OCCE Courtroom Built-in SSA Jacksonville, NC OCCE Courtroom Built-in SSA 2015014.00 Jacksonville, NC ADDENDUM 2 ADDENDUM DATE: November 13, 2017 PROJECT: OWNER: ARCHITECT: BIDS DUE: Courthouse Courtroom Built-in 109 Old Bridge Street Jacksonville,

More information

SECTION ARCHITECTURAL WOODWORK. B. Related Sections: 1. Section Paints and Coatings: Field applied painted finishes.

SECTION ARCHITECTURAL WOODWORK. B. Related Sections: 1. Section Paints and Coatings: Field applied painted finishes. PART 1 - GENERAL 1.1 SUMMARY SECTION 06 40 00 A. Provide architectural woodwork as shown and specified. Work includes: 1. Providing plastic laminate finished casework. 2. Providing plastic laminate clad

More information

SECTION INTERIOR FINISH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS

SECTION INTERIOR FINISH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS SECTION 062023 - INTERIOR FINISH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION CUSTOM CABINETS

SECTION CUSTOM CABINETS PART 1 GENERAL 1.01 SECTION INCLUDES A. Specially fabricated cabinet units. B. Countertops. C. Cabinet hardware. D. Preparation for installing utilities. 1.02 RELATED REQUIREMENTS SECTION 06410 - A. Section

More information

SECTION INTERIOR ARCHITECTURAL WOODWORK. A. Section includes interior woodwork items indicated not specified elsewhere and as specified.

SECTION INTERIOR ARCHITECTURAL WOODWORK. A. Section includes interior woodwork items indicated not specified elsewhere and as specified. SECTION 06 40 23 INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. Section includes interior woodwork items indicated not specified elsewhere and as specified. B. Options: 1. Where casework

More information

SECTION INTERIOR ARCHITECTURAL WOODWORK

SECTION INTERIOR ARCHITECTURAL WOODWORK SECTION 064023 PART 1 - GENERAL 1.1 SUMMARY This Section includes the following: 1. Architectural wood casework: a. Plastic-laminate-faced cabinets. b. Wood-veneer-faced cabinets. 2. Countertops: a. Solid-surfacing

More information

MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 06 WOOD, PLASTICS AND COMPOSITES

MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 06 WOOD, PLASTICS AND COMPOSITES SECTION 064023 - INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Interior standing and running trim. 2. Interior frames and jambs. 3. Stairwork and

More information

SECTION FINISH CARPENTRY

SECTION FINISH CARPENTRY SECTION 06200 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to

More information

Chevy Chase Club June 30, 2008 Bowie Gridley Architects

Chevy Chase Club June 30, 2008 Bowie Gridley Architects SECTION 081433 - STILE AND RAIL WOOD DOORS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION INTERIOR FINISH CARPENTRY

SECTION INTERIOR FINISH CARPENTRY SECTION 06 20 23 PART 1 - GENERAL 1.01 SUMMARY A. Section includes the following items for field-applied paint finish: 1. Interior standing and running trim. 2. Interior plywood paneling. B. Related Sections

More information

SECTION PRE-MANUFACTURED CABINETS

SECTION PRE-MANUFACTURED CABINETS SECTION 12390 PRE-MANUFACTURED PART 1 GENERAL 1.1 DESCRIPTION OF WORK A. The work includes furnishing all labor, materials and equipment required to complete the Pre-Manufactured Cabinet work as shown

More information

A. This Section includes interior architectural woodwork items indicated on Drawings and specified in this Section.

A. This Section includes interior architectural woodwork items indicated on Drawings and specified in this Section. SECTION 064023 - INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. This Section includes interior architectural woodwork items indicated on Drawings and specified in this Section. 1.2 DEFINITIONS

More information

MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 08 - OPENINGS

MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 08 - OPENINGS SECTION 081433 - STILE AND RAIL WOOD DOORS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Exterior stile and rail wood doors and sidelites. 2. Interior stile and rail wood doors. 3. Interior fire-rated,

More information

ROWAN COUNTY AIRPORT APRIL 2017 TERMINAL EXPANSION

ROWAN COUNTY AIRPORT APRIL 2017 TERMINAL EXPANSION SECTION 12300 - MANUFACTURED CASEWORK PART 1 - GENERAL RELATED DOCUMENTS: Drawings, General Conditions and Supplementary General Conditions and other Division-1 Specification Sections, apply to this Section.

More information

Music Area Casework General 1.01 Summary Related Sections Definitions Qualifications and Quality Assurance

Music Area Casework General 1.01 Summary Related Sections Definitions Qualifications and Quality Assurance 1.00 General 1.01 Summary Music Area Casework A. This section includes the following Scope of Work as referred to in the plans: 1. Thermally Fused Laminate manufactured casework, for use in music areas,

More information

Tender No Section St. James - Assiniboia Centennial Pool Fitness Facility Addition Page 1

Tender No Section St. James - Assiniboia Centennial Pool Fitness Facility Addition Page 1 Fitness Facility Addition Page 1 PART 1 GENERAL 1.1 SECTION INCLUDES.1 Finish carpentry items including shop prefabricated casework and countertops..2 Hardware and attachment accessories..3 Wood Benches..4

More information

SECTION ROUGH CARPENTRY

SECTION ROUGH CARPENTRY SECTION 06 10 00 ROUGH CARPENTRY PART 1 - GENERAL 1.01 SUMMARY A. Section includes: 1. Framing with dimension lumber. 2. Wood blocking and nailers. 3. Plywood backing panels. 1.02 ACTION SUBMITTALS A.

More information

E.M. Crouthamel Elementary School SECTION ROUGH CARPENTRY

E.M. Crouthamel Elementary School SECTION ROUGH CARPENTRY SECTION 061000 ROUGH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

Ash Brook Golf Course Scotch Plains, New Jersey

Ash Brook Golf Course Scotch Plains, New Jersey SECTION 062013 - EXTERIOR FINISH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

DIVISION 6 WOOD, PLASTICS AND COMPOSITES

DIVISION 6 WOOD, PLASTICS AND COMPOSITES DIVISION 6 WOOD, PLASTICS AND COMPOSITES PART 1 GENERAL 1.01 SECTION INCLUDES SECTION 06 1000 ROUGH CARPENTRY A. Rough opening framing for doors, windows, and roof openings. B. Roofing nailers. C. Preservative

More information

SECTION ARCHITECTURAL WOOD CASEWORK

SECTION ARCHITECTURAL WOOD CASEWORK PART 1 GENERAL 1.01 SECTION INCLUDES A. Specially fabricated cabinet units. B. Countertops. C. Cabinet hardware. D. Factory finishing. E. Preparation for installing utilities. 1.02 SUBMITTALS SECTION 06

More information

CaseworkUSA. specifications. 1.1 General 1.2 Summary. 1.3 Related Sections. 1.4 Definitions. 1.5 Qualifications and Quality Assurance

CaseworkUSA. specifications. 1.1 General 1.2 Summary. 1.3 Related Sections. 1.4 Definitions. 1.5 Qualifications and Quality Assurance 1.1 General 1.2 Summary A. This section includes the following Scope of Work as referred to in the plans: 1. Plastic laminate manufactured casework 2. Plastic laminate countertops 1.3 Related Sections

More information

B. Section Rough Carpentry: Support framing, grounds, and concealed blocking.

B. Section Rough Carpentry: Support framing, grounds, and concealed blocking. SECTION 06 41 00 - ARCHITECTURAL WOOD CASEWORK PART 1: GENERAL 1.1 SECTION INCLUDES A. Specially fabricated cabinet units. B. Cabinet hardware. C. Factory finishing. 1.2 RELATED REQUIREMENTS A. Division

More information

B. Shop Drawings: For horizontal louver blinds, include fabrication and installation details.

B. Shop Drawings: For horizontal louver blinds, include fabrication and installation details. HIGGINSVILLE HABILITATION CENTER MISC. BUILDING RENOVATIONS STATE OF MISSOURI HIGGINSVILLE, MISSOURI SECTION 122113- HORIZONTAL LOUVER BLINDS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general

More information

SECTION CUSTOM CASEWORK

SECTION CUSTOM CASEWORK PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 06 41 00 CUSTOM CASEWORK A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification sections,

More information

A. All trim that has been damages, broken, or missing shall be repaired or replaced with material of the same size, shape, and type.

A. All trim that has been damages, broken, or missing shall be repaired or replaced with material of the same size, shape, and type. SECTION 062000 - FINISH CARPENTRY PART 1 - GENERAL 1.1 SECTION REQUIREMENTS A. All trim that has been damages, broken, or missing shall be repaired or replaced with material of the same size, shape, and

More information

A. Boards or Strips: Lumber of less than 2 inches nominal size in least dimension.

A. Boards or Strips: Lumber of less than 2 inches nominal size in least dimension. HIGGINSVILLE HABILITATION CENTER MISC. BUILDING RENOVATIONS STATE OF MISSOURI HIGGINSVILLE, MISSOURI SECTION 061000 - ROUGH CARPENTRY PART 1 -GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions

More information

A. Provide all finish carpentry needed for a complete and proper installation.

A. Provide all finish carpentry needed for a complete and proper installation. SECTION 06200 - PART ONE GENERAL 1.1 SECTION INCLUDES A. Provide all finish carpentry needed for a complete and proper installation. B. Provide all wood, nails, bolts, screws, and all other items needed

More information

Copyright 2017 AIA MasterSpec Premium 05/17 PRODUCT MASTERSPEC LICENSED BY ARCOM TO WEREVER PRODUCTS, INC.

Copyright 2017 AIA MasterSpec Premium 05/17 PRODUCT MASTERSPEC LICENSED BY ARCOM TO WEREVER PRODUCTS, INC. This Product MasterSpec Section is licensed by ARCOM to Werever Products, Inc. ("Licensee"). This proprietary Product MasterSpec Section uses modified original MasterSpec text. Revisions made to the original

More information

SECTION CUSTOM MILLWORK

SECTION CUSTOM MILLWORK PRT 1 GENERL 1.01 SECTION INCLUDES SECTION 06 41 00 Shop-fabricated plastic laminate-clad cabinet units. B. Countertops. C. Cabinet hardware. 1.02 SUBMITTLS See Section 01 30 00 -dministrative Requirements,

More information

NATURAL TOFFEE SABLE SEDONA KONA SENECA RIDGE MAPLE

NATURAL TOFFEE SABLE SEDONA KONA SENECA RIDGE MAPLE NATURAL TOFFEE SABLE SEDONA KONA SENECA RIDGE MAPLE Framed Door Styles Traditional Overlay Raised Panel Wood veneered raised panel doors feature concealed nickel-finished self-closing hinges. Drawer fronts

More information

WELLNESS CENTER REMODEL UNIVERSITY OF CALIFORNIA, MERCED MERCED, CALIFORNIA PROJECT NO.: 907432 C. Solid Surfacing Material: 1. Manufacturers: D. Wood: a. First Floor; Wilsonart International, Solid Surfaces,

More information

B. Related Requirements: 1. Section "Interior Painting" for priming and backpriming of interior finish carpentry.

B. Related Requirements: 1. Section Interior Painting for priming and backpriming of interior finish carpentry. 1 ~GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY

More information

SECTION INTERIOR FINISH CARPENTRY. A. Lumber grading agencies, and the abbreviations used to reference them, include the following:

SECTION INTERIOR FINISH CARPENTRY. A. Lumber grading agencies, and the abbreviations used to reference them, include the following: SECTION 06 2023 PART 1 GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Interior standing and running trim. 2. Interior stairs. 1.2 DEFINITIONS A. Lumber grading agencies, and the abbreviations

More information

DIVISION 6 WOODS AND PLASTICS SECTION FINISH CARPENTRY

DIVISION 6 WOODS AND PLASTICS SECTION FINISH CARPENTRY DIVISION 6 WOODS AND PLASTICS SECTION 06 20 23 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

B. American Society for Testing and Materials (ASTM):

B. American Society for Testing and Materials (ASTM): SECTION 06400 ARCHITECTURAL WOODWORK PART 1 GENERAL 1.01 SUMMARY A. Provide necessary services, tools, equipment, material, and labor required to furnish and install millwork and cabinet work. Install

More information

Coordinate installation of rough carpentry members specified in other sections.

Coordinate installation of rough carpentry members specified in other sections. 1 1.03 Preservative treated wood materials. Concealed wood blocking, nailers, and C. Miscellaneous wood nailers, furring, and grounds. PART2 2.01 See Section 01 30 00 =Administrative Requirements, for

More information

Bovard Studios Inc. Section April 6, 2004 Page 1

Bovard Studios Inc. Section April 6, 2004 Page 1 April 6, 2004 Page 1 This section includes solid flush and surface articulated wood doors, may have veneer facing, solid or glazed (stained glass) design, factory pre-fit, may be factory finished or site

More information

***************************************************************************************************************

*************************************************************************************************************** 06400 ARCHITECTURAL WOODWORK SPECIFIER: CSI MasterFormat 2004 number 06 40 00 PART 1 GENERAL 1.1 SUMMARY A. Provide necessary services, tools, equipment, material, and labor required to furnish and install

More information

TENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018

TENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018 SECTION 055000 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply

More information

SECTION LAMINATE CLAD CASEWORK - COMMERCIAL

SECTION LAMINATE CLAD CASEWORK - COMMERCIAL SECTION 123400 LAMINATE CLAD CASEWORK - COMMERCIAL PART 1 GENERAL 1.01 SECTION INCLUDES A. Fixed modular laminate clad casework and components. B. Flexible rail mounted laminate clad casework and components.

More information

Alexandra Secondary College Refurbishment Project No: 1507 SECTION MANUFACTURED CASEWORK - SHOP BUILT 12300/1

Alexandra Secondary College Refurbishment Project No: 1507 SECTION MANUFACTURED CASEWORK - SHOP BUILT 12300/1 SECTION 12300 MANUFACTURED CASEWORK - SHOP BUILT 12300/1 PART I GENERAL 101 Scope The work of this Section covers the supply and installation of manufactured casework items. It includes but is not limited

More information

A. Dimension Lumber: Lumber of 2 inches nominal or greater but less than 5 inches nominal in least dimension.

A. Dimension Lumber: Lumber of 2 inches nominal or greater but less than 5 inches nominal in least dimension. SECTION 061000- ROUGH CARPENTRY PART 1- GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 0 I Specification Sections,

More information

WOOD WOOD

WOOD WOOD 12655 - WOOD 12655-1 Part One - General WOOD 1.0 All materials used in the finishing shall be of the highest grade of their respective kinds. Materials shall be evenly and smoothly applied by skilled mechanics.

More information

Request for Quotation. 1. The fabrication and installation of millwork as per attached specifications and drawings issued for construction.

Request for Quotation. 1. The fabrication and installation of millwork as per attached specifications and drawings issued for construction. Seven Oaks School Division MAINTENANCE/TRANSPORTATION/CUSTODIAL SERVICE CENTRE 2536 McPhillips Street Winnipeg, MB R2V4J8 Telephone: 204-338-7991 or 204-338-7051 Fax: 204-334-6889 June 29, 2018 Request

More information

Architectural Woodwork Standards. casework. s e c t i o n

Architectural Woodwork Standards. casework. s e c t i o n Architectural Woodwork Standards casework s e c t i o n SECTION Introductory INFORMATION Guide Specifications...284 Introduction...285 Categories...285 Wood...285 Decorative Laminate...285 Solid Phenolic...285

More information

SECTION WOOD DOORS

SECTION WOOD DOORS SECTION 08211 WOOD DOORS Notice to Vendors: CANV prefers to purchase products that contain tropical wood only if they are certified according to the guidelines of the Forest Stewardship Council (FSC).

More information

ADDENDUM NO. 1 THOROUGHBRED ROOM RENOVATION PHASE II DINING AREA MURRAY STATE UNIVERSITY, MURRAY, KY PROJECT #

ADDENDUM NO. 1 THOROUGHBRED ROOM RENOVATION PHASE II DINING AREA MURRAY STATE UNIVERSITY, MURRAY, KY PROJECT # ADDENDUM NO. 1 THOROUGHBRED ROOM RENOVATION PHASE II DINING AREA MURRAY STATE UNIVERSITY, MURRAY, KY PROJECT #13-046 10-23-2013 Bidders shall acknowledge receipt of this Addendum on the Bid Form, in the

More information

Section Rough Carpentry

Section Rough Carpentry Section 06 10 00 Rough Carpentry 06 10 00-1 PART 1 - GENERAL 1.01 SECTION INCLUDES A. Blocking in wall and roof openings; wood furring and grounds; electrical panel back boards, concealed wood blocking.

More information

Section "Rough Carpentry" for wood blocking for anchoring laboratory casework.

Section Rough Carpentry for wood blocking for anchoring laboratory casework. SECTION 1235519 - PART 1 - GENERAL 1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this

More information

A. Work of this Section, as shown or specified, shall be in accordance with the requirements of the Contract Documents.

A. Work of this Section, as shown or specified, shall be in accordance with the requirements of the Contract Documents. Section 06400 Page 1 Section 06400 ARCHITECTURAL WOODWORK PART 1 GENERAL 1.1 GENERAL REQUIREMENTS A. Work of this Section, as shown or specified, shall be in accordance with the requirements of the Contract

More information

SECTION ROUGH CARPENTRY

SECTION ROUGH CARPENTRY SECTION 06100 ROUGH CARPENTRY PART 1- GENERAL 1.1 SCOPE A. Work included under this section shall include all materials and labor necessary to fully complete all rough carpentry, including, but not necessarily

More information

SECTION FINISH CARPENTRY

SECTION FINISH CARPENTRY PART 1 - GENERAL 1.1 DESCRIPTION SECTION 06 20 00 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable

More information

Product Guide Specification

Product Guide Specification Shield Casework February 2014 3421 Merriam Lane Overland Park, Kansas 66203 Phone 913-744-2183 Fax 913-384-3477 Website www.shieldcasework.com E-mail info@shieldcasework.com Product Guide Specification

More information

Project Specifications Section SECTION ROUGH CARPENTRY Issued Final:

Project Specifications Section SECTION ROUGH CARPENTRY Issued Final: Project Specifications Section 061000 ROUGH CARPENTRY SECTION 061000 - ROUGH CARPENTRY Issued Final: 02-01-17 PART 1 - GENERAL 1.1 SUMMARY A. Scope: 1. Provide rough carpentry items where shown on the

More information

Multi-Institutional Academic Health Science & Research Center Evansville, IN

Multi-Institutional Academic Health Science & Research Center Evansville, IN SECTION 06 2023 - INTERIOR FINISH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.

.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Rough

More information

RIVERSIDE MEDICAL CENTER 5/09

RIVERSIDE MEDICAL CENTER 5/09 SECTION 06200 - FINISH CARPENTRY PART 1 - GENERAL 1.01 DESCRIPTION: A. Work of this section is subject to requirements of the Contract Documents including the General Conditions and Supplementary Conditions

More information

SECTION FINISH CARPENTRY. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.

SECTION FINISH CARPENTRY. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. SECTION 062000 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting

More information

B. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.

B. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details. SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.

More information

AMPCO PRODUCTS, INC. TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS

AMPCO PRODUCTS, INC. TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS A. Drawings and General Provisions of Contract, including General and Supplementary Conditions and

More information

Addendum. McKee and Associates Architecture and Interior Design. No. ONE Date: Project:

Addendum. McKee and Associates Architecture and Interior Design. No. ONE Date: Project: McKee and Associates Architecture and Interior Design Addendum No. ONE Date: 10.8.18 Project: A New Office for Gaston Elementary School for The Etowah County Board of Education Gadsden, Alabama A1.1 GENERAL

More information

C. Installation shall be by experienced carpenters. Coordinate with plumbing and electrical contractors.

C. Installation shall be by experienced carpenters. Coordinate with plumbing and electrical contractors. 12300 - MANUFACTURED CASEWORK PART 1 - GENERAL 1.01 STIPULATIONS A. The specifications sections General Conditions, Special Requirements, and General Requirements form a part of this section by this reference

More information

TOWN OF CULPEPER POLICE STATION

TOWN OF CULPEPER POLICE STATION SECTION 05520 - HANDRAIL AND RAILINGS PART 1 GENERAL 1.01 SECTION INCLUDES A. Guardrails. 1.02 REFERENCE STANDARDS A. ASTM A 53/A 53M - Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated,

More information

SECTION (06400) - MANUFACTURED WOOD-VENEER-FACED CASEWORK

SECTION (06400) - MANUFACTURED WOOD-VENEER-FACED CASEWORK SECTION 12 32 13 (06400) - MANUFACTURED WOOD-VENEER-FACED CASEWORK PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Custom Cabinet Units a. Wood, Transparent Finish, Custom Cabinet Units 2. Cabinet

More information

SECTION WOOD ACCORDION FOLDING DOORS

SECTION WOOD ACCORDION FOLDING DOORS SECTION 08 3513 WOOD ACCORDION FOLDING DOORS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Wood accordion folding doors. B. Related Sections: 1. Division 01: Administrative, procedural, and temporary

More information

SECTION Display Case Door Series 1301-CM

SECTION Display Case Door Series 1301-CM 1 SECTION 12 3559 Display Case Door Series 1301-CM PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Display Case Glass Doors. 2. Sidelites. B. Related work in other sections: 1. 08 8000- Glazing

More information

C. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors available.

C. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors available. SECTION 105113 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

Product Guide Specification

Product Guide Specification RYNONE March 2, 2011 North Thomas Avenue, PO Box 128, Sayre, Pennsylvania 18840 P: (570) 888-5272 F: (570) 888-1175 W: www.rynone.com Product Guide Specification Specifier Note: This product guide specification

More information

ROANOKE ISLAND AQUARIUM TURTLE REHABILITATION CENTER SECTION ROUGH CARPENTRY PART 1 - GENERAL

ROANOKE ISLAND AQUARIUM TURTLE REHABILITATION CENTER SECTION ROUGH CARPENTRY PART 1 - GENERAL SECTION 061000 - ROUGH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SCI-FAB Product Specifications. Casework Section 1. Part 1 General

SCI-FAB Product Specifications. Casework Section 1. Part 1 General SCI-FAB Product Specifications Casework Section 1 Part 1 General 1.1 SCOPE OF WORK Includes all factory fabricated stainless steel casework as required by the project drawings. 1.2 TYPICAL INCLUSIONS A.

More information

SECTION BULLET- RESISTANT DOORS

SECTION BULLET- RESISTANT DOORS 1 SECTION 08 3950 BULLET- RESISTANT DOORS PART 1- GENERAL 1.01 SUMMARY A. This Section Includes: 1. Bullet- resistant steel door and frame systems. 2. Door hardware for bullet- resistant steel door and

More information

SECTION INTERIOR ARCHITECTURAL WOODWORK

SECTION INTERIOR ARCHITECTURAL WOODWORK LSE ARCHITECTS, INC. LSE: 14.1001.01 SEWARD MONTESSORI SCHOOL ADDITION & REMODELING SECTION 06 40 23 PART 1 - GENERAL 1.01 SUMMARY A. Section Includes 1. Plastic-laminate clad cabinets and countertops.

More information

Product Guide Specification

Product Guide Specification VT Industries, Inc. 1000 Industrial Park PO Box 490 Holstein, Iowa 51025 Toll Free (800) 827-1615 Phone (712) 368-4381 Fax (712) 368-4111 Website www.vtindustries.com E-mail info@vtindustries.com Product

More information

SECTION PLASTIC LAMINATED CASEWORK

SECTION PLASTIC LAMINATED CASEWORK Specifications SECTION 123400 PLASTIC LAMINATED CASEWORK PART 1 GENERAL 1.01 SECTION INCLUDES This section provides the guidelines and standards for the manufacturing of plastic laminated casework and

More information

DIVISION 6 WOOD AND PLASTICS

DIVISION 6 WOOD AND PLASTICS DIVISION 6 WOOD AND PLASTICS PART 1 - GENERAL 1.01 SUMMARY A. This Section includes the following: 1. Wood framing. 2. Wood supports. 3. Wood blocking. 4. Wood cants. 5. Wood nailers. 6. Wood furring.

More information

The City of Winnipeg Section St. Vital Park Pavilion Page 1 of 1

The City of Winnipeg Section St. Vital Park Pavilion Page 1 of 1 The City of Winnipeg Section 06 10 13 WOOD BLOCKING AND CURBING St. Vital Park Pavilion Page 1 of 1 Part 1 General 1.1 SECTION INCLUDES.1 Roof curbs..2 Blocking in wall and roof openings..3 Wood furring

More information

SECTION HOLLOW METAL DOORS AND FRAMES

SECTION HOLLOW METAL DOORS AND FRAMES SECTION 081113 HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: Include construction details, material

More information