5'x10'x6' Enclosure-Dog Run Assembly Instruction

Size: px

Start display at page:

Download "5'x10'x6' Enclosure-Dog Run Assembly Instruction"

Geoffrey Foster
5 years ago
Views:

1 5'x10'x6' Enclosure-Dog Run Assembly Instruction Part One: Components for Dog Run 1. Door Panel: 1 pcs 2. Side Panels : 5 pcs 3. Gate Latch: 1 pcs 4. Clamp : 12 pcs Optional Parts List 5. A- Frame Roof set : 1 set 6. Top Roof Cover : 1 pcs 7. Base Foot : 6 pcs 8. 75mm expandable bolts:12pcs 9. 45mm bolt:12 pcs 10. Ropes for roof 11. Side Cover : 1 3 SETS 12. Feeder/ Waterer Door Panel Side Panel A-Frame Clamp Gate Latch Base Foot

Part Two : Assembly Instructions Step 1. Start at a back corner. Left or Right. Which ever is easiest for your assembly. Erect 2 side panels at right angles to make your corner shape.

2 Part Two : Assembly Instructions Step 1. Start at a back corner. Left or Right. Which ever is easiest for your assembly. Erect 2 side panels at right angles to make your corner shape.(refer to Picture One). You will now need 3 base feet. Place one on the ground in the corner. Insert one side panel pipe over the base foot tube. Then insert the other side panel over the second tube of the same base foot. (Refer to Picture Two). Then place the 2 nd and 3 rd base foot at the ends of each side panel. It is much easier to place the base foot components under your side panels as you go. Then secure your corner with two clamps. One at the top and one at the bottom. Make your clamps firm but tighten at the very end. NOTE: You may find you do not need to use the bottom clamp if you use the base foot on a slightly uneven surface such as grass. If you set your run up without the base feet you will need the second clamp at the bottom. Picture one: Corner

Picture Two: Base Foot and clamp at Corner Base Foot on Straight

Add one side panel with 2 pcs of clamps and 1 pcs of base foot to

Make clamps firm but tighten at end. Picture Three Step 3.

3 Picture Two: Base Foot and clamp at Corner Base Foot on Straight Line Direction Step 2. Add one side panel with 2 pcs of clamps and 1 pcs of base foot to make your next corner. (Refer to Picture Three). Make clamps firm but tighten at end. Picture Three Step 3. Add another 2 pcs of side panels with 4 pcs of clamps and 2 pcs of base foot. (refer to picture four). Once again make clamps firm but tighten at end.

4 Picture Four Step 4. Erect the door panel with 4 pcs of clamps. Place on top of base foot at the same time. (Refer to Picture Five). You can install the gate where ever it suits your needs. Picture Five

Please tighten the entire run. Step 6. Assemble A-Frame of Roof as Below.

5 Step 5. Assemble the gate latch to the gate panel at a height that is convenient to yourself. Using the U-shaped bolt. Make sure you attach the latch to the main frame of the gate and NOT the gate itself. If you have bought the Model without the roof, you are now complete. Please tighten the entire run. Step 6. Assemble A-Frame of Roof as Below. Insert all 3 Gable sections of the roof on top of your dog run first. They slide into the pipe section at the top of each side panel. (Pic 8 ). Insert the straight rods between the gables of your roof, connecting your 3 gables together. (Pic 9) Picture 8 Picture 9

Then around the top pipe again and though the next eyelet and so on.

6 Step 7. Place your top roof cover over the A-Frame. Use rope to fix the roof cover onto the pipe of your side panels. Affix one end to the top pipe of a side panel and then thread through the eyelet on the roof cover. Then around the top pipe again and though the next eyelet and so on. (Refer to picture 11) Take your time and once it is all in position, go around again and pull the roof nice and firm Picture 11 Now tighten the entire run. Step 8: Now that you run is complete. You can affix to the ground with the expandable bolts. Also now use the 45 mm bolts and connect your panels to your base feet.

Place Optional Side Covers on any side panel to suit your conditions.

7 Step 9. If you have purchased optional side covers you can now connect the side cover together with the top roof cover via the Velcro. And fix the side cover on the side panel via the plastic rope. Place Optional Side Covers on any side panel to suit your conditions. You will notice that you have a his and her pair. You can separate and use as a single panel or keep together as a pair and prevent any caps between the two.

Step 10. If you have purchased the feeder/waterer.

bracket and place that on the outside of the run and connect with the

You can keep the bowls secure by leaving the black tab screwed over

8 Step 10. If you have purchased the feeder/waterer. You can connect this to any spot that is convenient to you and your setup. Place the main frame on the inside of the run, then take a flat bracket and place that on the outside of the run and connect with the bolts provided. You can keep the bowls secure by leaving the black tab screwed over the bowls in place. If you want to have the bowls free for easy removal, then remove the black tab by simply undoing and removing the screw and tab. The choice is yours.!! Thank you for choosing a Pets Outerspace Enclosure.

15'x10'x6' Enclosure - Dog Run Assembly Instruction

15'x10'x6' Enclosure - Dog Run Assembly Instruction Part One: Components for Dog Run 1. Door Panel: 1 pcs 2. Side Panels : 9 pcs 3. Gate Latch: 1 pcs 4. Clamp : 20pcs Optional Parts List 5. A- Frame Roof